DeWalt DCN21PLB Manuel utilisateur

Marque: DeWalt

Modèle: DCN21PLB

Catégorie: Cloueuse

Taper: Manuel utilisateur

Ce manuel convient également à

DCN21PLM1

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DCN21PL

20V Max* Cordless 21º Plastic Collated Framing Nailer

Cloueuse de charpente à bande en plastique 21º sans fil

20V max*

Pistola de Clavos para Enmarcado en Plástico 21º Inalámbrica

20V Máx*

final page size: 8.5 x 5.5 in

ENGLISH

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 19

Español (traducido de las instrucciones originales) 39

ENGLISH

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

If you have any questions or comments about this or

any

DeWALT

tool, call us toll free at:

1-800-4-

DeWALT

(1-800-433-9258).

Trigger

Trigger lock-off

Depth adjustment wheel

Jam/stall indicator light

Stall release lever

Contact trip

Magazine

Pusher latch

Bump/sequential

selector switch

Rotating rafter hook

On-board hex wrench

Battery Pack

Dual speed switch

Handle

Fig. A

ENGLISH

GENERAL POWER TOOL SAFETY WARNINGS



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the

switch is in the off position before connecting to

power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your

finger on the switch or energizing power tools that

have the switch on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or

long hair can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-relatedhazards.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power

toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are

caused by poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

ENGLISH

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardoussituation.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

orburns.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool ismaintained.

Nailer Safety Warnings

• Always assume that the tool contains fasteners.

Careless handling of the nailer can result in unexpected

firing of fasteners and personalinjury.

• Do not point the tool towards yourself or anyone

nearby. Unexpected triggering will discharge a fastener

causing aninjury.

• Do not actuate the tool unless the tool is placed

firmly against the workpiece. If the tool is not in

contact with the workpiece, the fastener may be deflected

away from yourtarget.

• Disconnect the tool from the power source when the

fastener jams in the tool. While removing a jammed

fastener, the nailer may be accidentally activated if it is

pluggedin.

• Do not use this nailer for fastening electrical cables.

It is not designed for electric cable installation and may

damage the insulation of electric cables thereby causing

electric shock or firehazards.

Additional Nailer Safety Warnings



WARNING: When using any nailer, all safety

precautions, as outlined below, should be followed

to avoid the risk of death or serious injury. Read and

understand all instructions before operating thetool.



WARNING: NEVER spray or in any other way apply

lubricants or cleaning solvents inside the tool. This can

seriously affect the life and performance of thetool.



WARNING: If the tool has been dropped or you

suspect tool damage perform tool operation check as

defined in the mode selection section of the manual. If

it doesn’t perform according to the manual, stop using

the tool and have it serviced at an authorized

DeWALT

servicecenter.

• Keep hands and body parts away from the discharge

area of the tool. While in use NEVER grasp the tool by the

magazine or canister, a mis-driven nail can exit the nose

causing injury.

• Hold tool by insulated gripping surfaces when

performing an operation where the fastener may

contact hidden wiring. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock

theoperator.

• Actuating tool may result in flying debris, collation

material, or dust which could harm operator’s

eyes. Operator and others in work area MUST wear

safety glasses with side shields. These safety glasses

must conform to ANSI Z87.1 requirements (approved

glasses have “Z87” printed or stamped on them. It is

the employer’s responsibility to enforce the use of eye

protection equipment by the tool operator and other

people in the workarea.

• Always wear appropriate personal hearing and

other protection during use. Under some conditions

and duration of use, noise from this product may

contribute to hearingloss.

• Disconnect battery pack from the tool when not in

use. Always remove battery pack and remove fasteners

from magazine before leaving the area or passing the

tool to another operator. Do not carry tool to another

work area in which changing location involves the use

of scaffoldings, stairs, ladders, and the like, with battery

pack connected. Do not make adjustments, perform

maintenance or clear jammed fasteners while battery is

inplace.

• Do not remove, tamper with, or otherwise cause the

tool, trigger or trigger lock-off, to become inoperable.

Do not tape or tie trigger in the on position. Do not remove

spring from contact trip. Make daily inspections for free

movement of trigger. Uncontrolled discharge couldresult.

• Inspect tool before use. Do not operate a tool if any

portion of the tool, trigger, or trigger lock-off is

inoperable, disconnected, altered, or not working

properly. Damaged parts or missing parts should be

repaired or replaced before use. Refer toRepairs.

• Do not alter or modify the tool in anyway.

• Always assume that the tool containsfasteners.

• Do not point the tool at co-workers or yourself at

any time. No horseplay! Work safe! Respect the tool as a

workingimplement.

• Keep bystanders, children, and visitors away while

operating a power tool. Distractions can cause you to

ENGLISH

lose control. When tool is not in use, it should be locked in

a safe place, out of the reach ofchildren.

• Always use trigger lock-off when tool is not in

immediate use. Using the trigger lock-off will prevent

accidentaldischarge.

• Do not overreach. Maintain proper footing and balance

at all times. Loss of balance may cause personalinjury.

• Use the tool only for its intended use. Do not

discharge fasteners into open air, concrete, stone,

extremely hard woods, knots or any material

too hard for the fastener to penetrate. Do not

use the body of the tool or top cap as a hammer.

Discharged fastener may follow unexpected path

and causeinjury.

• Always keep fingers clear of contact trip to prevent

injury from inadvertent release of thepusher.

• Refer to the Maintenance and Repairs sections for

detailed information on the proper maintenance of

thetool.

• Always operate the tool in a clean, lighted area.

Be sure the work surface is clear of any debris and be

careful not to lose footing when working in elevated

environments such asrooftops.

• Do not drive fastener near edge of material. The

workpiece may split causing the nail to ricochet, injuring

you or a co-worker. Be aware that the fastener may follow

the grain of the wood (shiner), causing it to protrude

unexpectedly from the side of the work material. Drive the

chisel point of the fastener perpendicular to the grain to

reduce risk ofinjury.

• Do not drive nails onto the heads of other fasteners

or with the tool at too steep an angle. Personal injury

from strong recoil jammed nails, or ricocheted nails

mayresult.

• Keep hands and body parts clear of immediate work

area. Hold workpiece with clamps when necessary to

keep hands and body out of potential harm. Be sure the

workpiece is properly secured before pressing the nailer

against the material. The contact trip may cause the work

material to shiftunexpectedly.

• Do not use tool in the presence of flammable dust,

gases or fumes. The tool may produce a spark that could

ignite gases causing a fire. Driving a nail into another nail

may also cause aspark.

• Keep face and body parts away from back of the tool

cap when working in restricted areas. Sudden recoil

can result in impact to the body, especially when nailing

into hard or densematerial.

• Grip tool firmly to maintain control while allowing

tool to recoil away from work surface as fastener

is driven. In Bump mode if contact trip is allowed to

recontact work surface before trigger is released an

unwanted fastener will befired.

• Choice of triggering method is important. Check the

manual for triggeringoptions.

• Always select an actuation system that is

appropriate to the fastener application and the

training of theoperator.

• Use caution when handling, loading or unloading

fasteners. Fasteners have sharp points which could

causeinjury.

• Only wear gloves that provide adequate feel and

safe control of the trigger and any adjustingdevices.

Bump/Sequential Selector Switch

Sequential Action

• When using the tool in sequential action, do not

actuate the tool unless the tool is placed firmly

against theworkpiece.

Bump Action

• When using the tool in bump action, be careful of

unin tentional double fires resulting from tool recoil.

Unwanted fasteners may be driven if the contact trip is

allowed to accidentally re-contact the worksurface.

• To Avoid Double Fires:

ʵ Do not engage the tool against the work surface with

a strongforce.

ʵ Allow the tool to recoil fully after eachactuation.

ʵ Use sequential actionmode.

• When bump actuating the framing nailer, always

keep tool in control. Inaccurate placement of tool can

result in misdirected discharge of anail.

• Be aware of material thickness when using nailer. A

protruding nail may causeinjury.

• Depth adjustment: To reduce risk of serious injury

from accidental actuation when attempting to

adjust depth, ALWAYS;

ʵ Remove batterypack.

ʵ Engage trigger lock-off.

ʵ Avoid contact with trigger during adjustments

• Do not drive nails blindly into walls, floors or other

work areas. Fasteners driven into live electrical wires,

plumbing, or other types of obstructions can result in

injury and or propertydamage.

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use tool while tired or under the influence of drugs,

alcohol, or medication. A moment of inattention

while operating power tools may result in serious

personalinjury.

Additional Safety Information



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

ENGLISH

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.



WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.



CAUTION: When not in use, place tool on its side

on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be

caught in movingparts.

The label on your tool may include the following symbols.

The symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

.......................no load speed

n .........................rated speed

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... read all

documentation

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

Your tool uses a

DeWALT

charger. Be sure to read all safety

instructions before using your charger. Consult the chart

at the end of this manual for compatibility of chargers and

batterypacks.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into

a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult

the chart at the end of this manual for compatibility of

batteries andchargers.

• Charge the battery packs only in designated

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and

materials are created when lithium ion battery packs

areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of

a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.

ENGLISH



WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark orflame.



WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case

is cracked or damaged, do not insert into the charger.

Do not crush, drop or damage the battery pack. Do

not use a battery pack or charger that has received a

sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be

returned to the service center forrecycling.

Transportation



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do

not place the battery pack in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries

can possibly cause fires if the battery terminals

inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes in

carry-on baggage UNLESS they are properly protected

from short circuits. So when transporting individual

battery packs, make sure that the battery terminals

are protected and well insulated from materials that

could contact them and cause a shortcircuit.

Shipping the

DeWALT

FLEXVOLT™ Battery

The D

WALT FLEXVOLT™ battery has two modes: Use and

Shipping.

Use Mode: When the FLEXVOLT™ battery stands alone or is

in a D

WALT 20V Max* product, it will operate as a 20V Max*

battery. When the FLEXVOLT™ battery is in a 60V Max* or a

120V Max* (two 60V Max* batteries) product, it will operate

as a 60V Max* battery.

Shipping Mode: When

the cap is attached to the

FLEXVOLT™ battery, the

battery is in Shipping Mode.

Strings of cells are electrically

disconnected within the pack resulting in three batteries

with a lower Watt hour (Wh) rating as compared to one

battery with a higher Watt hour rating. This increased

quantity of three batteries with the lower Watt hour rating

can exempt the pack from certain shipping regulations that

are imposed upon the higher Watt hourbatteries.

The battery label indicates two Watt hour ratings (see

example). Depending on how the battery is shipped, the

appropriate Watt hour rating must be used to determine

the applicable shipping requirements. If utilizing the

shipping cap, the pack will be considered 3 batteries at

the Watt hour rating indicated for “Shipping”. If shipping

without the cap or in a tool, the pack will be considered one

battery at the Watt hour rating indicated next to “Use”.

USE: 120 Wh Shipping: 3 x 40 Wh

Example of Use and Shipping Label Marking

For example, Shipping Wh rating might indicate 3 x 40 Wh,

meaning 3 batteries of 40 Watt hours each. The Use Wh

rating might indicate 120 Wh (1 batteryimplied).

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of

charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge

button. A combination of the three green LED lights will

illuminate designating the level of charge left. When the

level of charge in the battery is below the usable limit, the

fuel gauge will not illuminate and the battery will need to

berecharged.

Fig. B

NOTE: The fuel gauge is only an indication of the charge left

on the battery pack. It does not indicate tool functionality

and is subject to variation based on product components,

temperature and end-userapplication.

For more information regarding fuel gauge battery packs,

please contact call 1-800-4-

DeWALT

(1-800-433-9258) or

visit our website www.dewalt.com.

The RBRC® Seal

The RBRC® (Rechargeable Battery

Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-

ion batteries (or battery packs) indicates

that the costs to recycle these batteries

(or battery packs) at the end of their useful life have already

been paid by

DeWALT

. In some areas, it is illegal to place

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and

the Call2Recycle® program provides an environmentally

consciousalternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other

battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel

cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by

returning the spent nickel cadmium, nickel metal hydride

or lithium-ion batteries to an authorized

DeWALT

service

center or to your local retailer for recycling. You may also

contact your local recycling center for information on

ENGLISH

where to drop off the spent battery. RBRC® is a registered

trademark of Call 2 Recycle,Inc.

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• DO NOT attempt to charge the battery pack with

any chargers other than the ones in this manual.

The charger and battery pack are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging

DeWALT

rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the greater the capacity

of the cable, that is, 16 gauge has more capacity than 18

gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using

more than one extension to make up the total length,

be sure each individual extension contains at least the

minimum wire size. The following table shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or

place the charger on a soft surface that might block

the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top

and the bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.



WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock mayresult.



WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the

battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service

center forrecycling.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable battery packs.

Other types of batteries may overheat and burst

resulting in personal injury and propertydamage.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting toclean.

Charging a Battery (Fig. C)

1. Plug the charger into an appropriate outlet before

inserting batterypack.

ENGLISH

Fig. C

2. Insert the battery pack

12

into the charger, making sure

the battery pack is fully seated in the charger. The red

(charging) light will blink continuously indicating that

the charging process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is

fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger,

push the battery release button

25

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-

ion battery packs, charge the battery pack fully before

firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

Charging

Fully Charged

Hot/Cold Pack Delay**

** DCB107, DCB112, DCB113, DCB115, DCB118,

DCB132: The red light will continue to blink, but a yellow

indicator light will be illuminated during this operation.

Once the battery pack has reached an appropriate

temperature, the yellow light will turn off and the charger

will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery

pack. The charger will indicate faulty battery pack by

refusing tolight.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and

battery pack to be tested at an authorized servicecenter.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan

designed to cool the battery pack. The fan will turn on

automatically when the battery pack needs to becooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of thecharger.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against

overloading, overheating or deepdischarge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the lithium-

ion battery pack on the charger until it is fullycharged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

These chargers are designed to be wall mountable or to

sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet,

and away from a corner or other obstructions which may

impede air flow. Use the back of the charger as a template

for the location of the mounting screws on the wall. Mount

the charger securely using drywall screws (purchased

separately) at least 1" (25.4 mm) long, with a screw head

diameter of 0.28–0.35" (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32" (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non-metallic brush. Do not use water or

any cleaningsolutions.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18° – 24°C). DO NOT charge

the battery pack below +40°F (+4.5°C), or above

+104°F (+40°C). This is important and will prevent

serious damage to the batterypack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

ENGLISH

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out the

lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

4. The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may

also charge a partially used pack whenever you desire

with no adverse effect on the batterypack.

5. Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Always

unplug the charger from the power supply when there

is no battery pack in the cavity. Unplug the charger

before attempting toclean.

6. Do not freeze or immerse the charger in water or any

otherliquid.

Storage Recommendations

1. The best storage place is one that is cool and dry, away

from direct sunlight and excess heat orcold.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool dry place out of the

charger for optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be

recharged beforeuse.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (FIG. A)



WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

Refer to Figure A at the beginning of this manual for a

complete list ofcomponents.

Intended Use

The DCN21PL cordless framing nailer has been designed for

driving nails into woodenworkpieces.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

This cordless framing nailer is a professional power tool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

NOTICE: NEVER spray or in any other way apply

lubricants or cleaning solvents inside the tool. This

can seriously affect the life and performance of

thetool.

TOOL SPECIFICATIONS

Firing mode Selective: Bump or Sequential

Voltage 20

Height 16.5" (419 mm)

Width 4" (104 mm)

Length 13.25" (335 mm)

Weight 8.5 lbs (3.85 kg)

Magazine angle 21°

Loading capacity Up to 49 nails

NAIL SPECIFICATIONS

Full Round Head

Nail lengths 2" – 3-1/4" (50 mm – 83 mm)

Shank diameters 0.113" – 0.148" (2.8 mm – 3.3 mm)

Nail stick angles 21°

Shank types Smooth and Ring

OPERATION



WARNING: Always wear safety glasses to protect

your eyes from flying construction debris. An optional

debris cover is available as an accesory to help reduce

contruction debris and collation material.



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Installing and Removing the Battery Pack

(Fig. D)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack

12

into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide

it into the handle until the battery pack is firmly seated in

the tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button

25

and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

ENGLISH

Fig. D

Proper Hand Position (Fig. E)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the handle

Fig. E

Mode Selection (Fig. F, G)



WARNING: Always wear proper eye [ANSI Z87.1

(CAN/CSA Z94.3)] and ANSI S12.6 (S3.19) hearing

protection when operatingtool.

The

DeWALT

cordless nailers are assembled in accordance

with the ANSI Standard SNT-101-2002.

The framing nailer is capable of firing nails using bump

actuation or sequential actuation. If you would like to

have the bump actuation mode disabled, have the tool

serviced by an authorized

DeWALT

service center. Before

operating this tool, look at the selector switch to determine

the actuation mode. Read all instructions before selecting

actuationmode.



WARNING: Keep fingers AWAY from trigger when

not driving nails to avoid accidental firing. NEVER

carry tool with finger on trigger. In bump mode tool

will fire a nail if contact trip is bumped while trigger

isdepressed.

Sequential Action

Use sequential action for intermittent nailing where

very careful and accurate placement and depth control

is desired. The sequential actuation mode provides the

maximum delivery of power for driving the longestnails.

To Operate the Nailer in Sequential Action Mode

1. Slide the selector switch

to the left, as shown in

FigureF.

2. Fully depress nosepiece against the work surface (motor

willstart).

3. Pull trigger (nail will drive into worksurface).

4. Releasetrigger.

5. Lift nosepiece off worksurface.

6. Repeat steps 2 through 4 for nextapplication.

NOTICE: The contact trip needs to be depressed

followed by a trigger pull for each nail followed by

a release of both the contact trip and trigger after

eachnail.

Fig. F

Bump Action

Bump action is intended for rapid nailing on flat, stationary

surfaces and typically most effective for applications that

require driving shorternails.

When using bump action, two methods are available: place

actuation and bumpactuation.

Slide the selector switch

to the right, as shown in

FigureG.

Fig. G

To Operate the Tool Using the Place Actuation Method



WARNING: A nail will fire each time the

trigger is depressed as long as the contact trip

remainsdepressed.

1. Depress the contact trip against the worksurface.

ENGLISH

2. Depress thetrigger.

To Operate the Tool Using the Bump Actuation Method

1. Depress thetrigger.

2. Push the contact trip against the work surface. As long

as the trigger is depressed, the tool will fire a nail every

time the contact trip is depressed. This allows the user

to drive multiple nails insequence.



WARNING: Do not keep trigger depressed when tool

is not in use. Keep the trigger lock-off in the locked

position when the tool is not inuse.



WARNING: When the tool’s motor is running, the

next actuation, pulling the trigger or depressing the

contact trip, will cause a nail tofire.

Speed Selection (Fig. A, H)

This nailer is equipped with a dual speed selection

switch

13

located on thefoot.

• For shorter nails, select speed 1 by setting the switch to

the left mostposition.

• For longer nails and more rigorous applications, select

speed 2 by setting the switch to the right mostposition.

In the event that nails are not driving to depth in speed

setting 1, you may have to switch to speed setting 2 for

additional drivingpower.

Fig. H

Suggested Speed Settings

Application Typical Nail Length Speed Setting

Framing & Decking 3-1/4" (83 mm) 2

General Framing 3" (77 mm) 2

Sheathing 2-3/8" (60 mm) 2

Fencing 2" (50 mm) 1

Preparing the Tool

NOTICE: NEVER spray or in any other way apply

lubricants or cleaning solvents inside the tool. This

can seriously affect the life and performance of

thetool.

NOTE: The battery pack is not fully charged out of the

carton. Follow instructions outlined (refer to Charging

aBattery).

1. Read the Nailer Safety Warnings section of

thismanual.

2. Wear eye and earprotection.

3. Remove battery fromtool.

4. Ensure magazine is empty of allfastners.

5. Check for smooth and proper operation of contact

trip and pusher assemblies. Do not use tool if either

assembly is not functioning properly. NEVER use

a tool that has the contact trip restrained in the

actuatedposition.

6. Keep tool pointed away from yourself andothers.

7. Insert fully charged batterypack.

Using the Trigger Lock-Off (Fig. I)



WARNING: To reduce the risk of serious personal

injury, do not keep trigger depressed when tool is not

in use. Keep the trigger lock-off switch LOCKED (Fig.I)

when the tool is not inuse.



WARNING: To reduce the risk of serious personal

injury, lock off trigger, disconnect battery pack

from tool and remove nails from magazine before

makingadjustments.

Each

DeWALT

nailer is equipped with a trigger lock-off

2

which when pushed to the right as shown in FigureI,

prevents the tool from firing a nail by locking the trigger and

bypassing power to themotor.

Fig. I

When the trigger lock-off is pressed to the left, the tool will

be fully operational. The trigger lock-off should always be

locked off (Fig.I) whenever any adjustments are made or

when tool is not in immediateuse.

NOTICE: Do not store tool with battery pack installed.

To prevent damage to the pack and to ensure best

battery life, store battery packs out of the tool or

charger in a cool, drylocation.

Loading the Tool (Fig. J)



WARNING: Keep the tool pointed away from yourself

andothers.



WARNING: Never load nails with the contact trip or

triggeractivated.



WARNING: Always remove battery pack before

loading or unloadingnails.



CAUTION: Keep fingers clear of pusher latch track to

preventinjury.



WARNING: The trigger lock-off should always be

engaged whenever any adjustments are made or

when tool is not inuse.

1. Turn the nailer upsidedown.

ENGLISH

2. Slide the spring-loaded pusher latch

8

to the base of

the magazine to lock it intoplace.

3. Drop nail strips into the loading slot of the magazine,

making sure the nail heads align correctly with the slot

opening. (Refer to Nail Specifications to determine

compatible size.)

Fig. J

4. Keeping fingers clear of the track, close the magazine by

releasing the pusher latch. Carefully allow the latch to

slide forward and engage the nailstrip.

Unloading the Tool



WARNING: The trigger lock-off should always be

locked off whenever any adjustments are made or

when tool is not inuse.

1. Slide the spring-loaded pusher latch to the base of the

magazine to lock it intoplace.

2. Tip the tool up until the fastener strip slides freely out of

themagazine.

3. With battery removed, check the nosepiece to verify

there are no nailsremaining.

Dry Fire Lock Out

The nailer is equipped with a dry fire lockout which prevents

the tool from actuating when the magazine in nearly empty.

When approximately 4 nails remain in the magazine, the

tool ceases to operate. Refer to Loading the Tool to reload a

stick of collatednails.

Adjusting Depth (Fig. K)

The depth that the nail is driven can be adjusted using the

depth adjustment wheel

3

on the nose of thetool.



WARNING: To reduce risk of serious injury from

accidental actuation when attempting to adjust

depth, ALWAYS:

• Remove batterypack.

• Engage trigger lock-off.

• Always point the nose of the nailer away

fromyou.

• Avoid contact with trigger duringadjustments.

1. To drive the nail shallower, rotate the depth adjustment

wheel

3

to the left, toward the shallow nailicon.

2. To drive a nail deeper, rotate the depth adjustment

wheel

3

to the right, toward the deeper nailicon.

Fig. K

Non-Mar Tip (Fig. L)

When using this tool on softer materials that you do not

want to mark, such as wood cladding, use the plastic non-

mar tip

15

over the contact trip

6

Fig. L

Jam/Stall Indicator Light (Fig. A)

There is a jam/stall indicator light

4

located on the foot of

thetool.

JAM/STALL CONDITION

Rotate the stall release

lever to release. Refer to

StallRelease.

Stall Release (Fig. M)

If the nailer is used in harder wood where all available

energy in the motor is used to drive a fastener, the tool

may stall. The driver blade will not complete the drive cycle

and the jam/stall indicator will flash. Rotate the stall release

lever

5

on the tool and the mechanism willrelease.

NOTE: The tool will disable itself and not reset until the

battery pack has been removed and reinserted. If the driver

blade does not automatically return to the home position,

proceed to Clearing a Jammed Nail. If the unit continues

to stall please review the material and fastener length to be

sure that it is not too rigorous anapplication.

ENGLISH

Fig. M

Clearing a Jammed Nail (Fig. A, N)



WARNING: To reduce the risk of serious personal

injury, disconnect battery pack from tool before

making any adjustments, changing accessories,

servicing, or moving the tool. Such preventative

safety measures reduce the risk of starting the

toolaccidentally.

If a nail becomes jammed in the nosepiece, keep the tool

pointed away from you and follow these instructions

toclear:

1. Remove battery pack from tool and engage trigger

lock-off.

2. Slide the spring-loaded pusher latch to the base of the

magazine to lock it into place and unload nailstrip.

3. Using the hex tool

11

provided, loosen the two hex

bolts

16

at the top of themagazine.

Fig. N

4. Rotate the magazine

7

forward.

5. Remove jammed/bent nail, using pliers ifnecessary.

6. If the driver blade is in the down position, rotate the stall

release lever on the top of thenailer.

NOTE: If the driver blade will not reset after rotating the

stall release lever, manually resetting the blade with a

long screw driver may benecessary.

7. Rotate the magazine back into position under the nose

of the tool and tighten hexbolts.

8. Reinsert batterypack.

NOTE: The tool will disable itself and not reset until the

battery pack has been removed andreinserted.

9. Reinsert nails into magazine (refer to Loading theTool).

10. Release the pusherlatch.

11. Disengage the trigger lock-off when ready to

continuenailing.

NOTE: Should nails jam frequently or the driver blade

continually fail to reset, have tool serviced by an authorized

DeWALT

servicecenter.

Cold Weather Operation

When operating tools at temperatures below freezing:

• Keep tool as warm as possible prior touse.

• Actuate the tool 10 or 15 times into scrap lumber

beforeusing.

Hot Weather Operation

Tool should operate normally. However, keep tool out of

direct sunlight as excessive heat can deteriorate bumpers

and other rubber parts resulting in increasedmaintenance.

Rotating Rafter Hook (Fig. O)



WARNING: Never use hook to hang tool from belt or

other clothing unless tool is in sequntial actionmode.



WARNING: Remove nails from magazine before

making any adjustments or servicing this tool. Failure

to do so may result in seriousinjury.



CAUTION: When not in use, place tool on its side

on a stable surface where it will not cause a

tripping or fallinghazard.



CAUTION: Some tools with large battery packs

will stand upright on the battery pack but may

be easily knockedover.

The

DeWALT

cordless nailer includes a rotating rafter

hook

10

and can be easily positioned to the left or right of

the tool to accommodate left- or right-handedusers.

If use of the hook is not desired at all, it can be rotated to

the front or back of the handlebase.

Fig. O

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

ENGLISH

DAILY MAINTENANCE CHART

ACTION Clean magazine, pusher, and contact

tripmechanism.

WHY Permits smooth operation of magazine,

reduces wear, and preventsjams.

HOW Blowing off the tool with compressed air is the

most effective way to clean the tool. The use

of oils, lubricants periodically or solvents is not

recommended as they tend to attract debris

and/or damage the plastic parts of thetool.

ACTION Before each use, check to ensure all screws

and fasteners are tight andundamaged.

WHY Prevents jams and premature failure of

toolparts.

HOW Tighten loose screws using the appropriate

hex wrench orscrewdriver.

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthis.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

Accessories



WARNING: Since accessories, other than those

offered by

DeWALT

, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories should be used with

thisproduct.

Recommended accessories for use with your tool

are available at extra cost from your local dealer or

authorized service center. If you need assistance in

locating any accessory, please contact

DeWALT

Industrial

Tool Co., 701East Joppa Road, Towson, MD 21286, call

1-800-4-

DeWALT

(1-800-433-9258) or visit our website:

www.dewalt.com.

Replacing the Return Springs and Profile



WARNING: For your own safety, read the tool

instruction manual before using any accessory.

Failure to heed these warnings may result in serious

personal injury and damage to the tool and the

accessory. When servicing this tool, use only identical

replacementparts.



CAUTION: If you don't feel comfortable servicing your

tool, take it to a

DeWALT

authorized service center.

The user should only attempt to service the springs

and profile. All other service should be completed by

an authorized

DeWALT

servicecenter.



CAUTION: Do not lubricate any of the replacement

parts. Lubrication can damage the parts and seriously

affect the life and performance of thetool.

NOTICE: All the mechanical parts of the spring

replacement kit are shown for convenience and

verification of inclusion. The kit also contains a packet

of Loctite adhesive for use in Step9. Refer to Fig.U.

DCN6901 Return Spring Replacement

Kit (Fig. P–U)

To Change Broken or Worn Return Springs

NOTE: Springs should be replaced as a pair, using only the

correct

DeWALT

accessory spring replacementkit.

1. Using the hex wrench

11

provided, loosen the two

screws

17

on either side of the unit. Refer to FigureP.

2. Remove the return system

18

from the unit. Refer to

FigureQ.

Fig. P

Fig. Q

3. Slide the spring rail clip

19

off of the spring rail

20

Refer to FigureR.

4. Twist and remove the spring bumper

21

and remove

the washer

22

and return spring

23

. Refer to FigureS.

ENGLISH

Fig. R

Fig. S

5. Mount the new return spring and washer on to the

spring rail

20

. While compressing the spring with the

washer near the opposite end of the rail, twist on the

new spring bumper until it is past the groove for the

spring railclip.

6. Mount the new spring rail clip securely and position the

bumper against theclip.

7. Repeat steps 3–6 to replace the secondspring..

NOTE: Check the return of the profile by sliding the

profile up the spring rail and letting it go. It should

return due to the force from thesprings.

8. Slide the return system

18

back into the unit. Tighten

the two screws

on either side of the unit. Check

proper installation by connecting a battery and pushing

then releasing the nose of the unit against a bench or

hard surface. This will start the motorspinning.

NOTE: When the profile and the flywheel are correctly

aligned, you will hear the motor coast back down

from full speed. If the profile and the flywheel are not

correctly aligned, the motor may not start up or may

slow down much faster than normal along with a loud

grinding noise from the unit. If this happens remove

battery, then remove and reseat the returnsystem.

Fig. T

9. Once the return system is correctly seated, open the

provided sachet of Loctite®*** and apply a small

amount on the thread of the two screws

17

and

remount the two screws using the hex wrench and

tightensecurely.

Fig. U



WARNING: Always test the unit by firing short nails

in to soft wood, to ensure that the tool is working

properly. If tool does not operate properly, contact a

recognized

DeWALT

service centerimmediately.



WARNING: LOCTITE® SACHET CONTENTS MAY

IRRITATE EYES, SKIN, AND RESPIRATORY SYSTEM. USE

ENTIRE CONTENTS ON OPENING. Do not breath fumes.

Do not get in eyes or on skin or clothing. Use only in a

well ventilated area. Keep out of reach ofchildren.

FIRST AID TREATMENT: Contains polyglycol

dimethacrylate, polyglycol oleate, propylene glycol,

titanium dioxide, and cumene hydroperoxide. If

swallowed, call a Poison Control Center or doctor

immediately. Do not induce vomitting. If breathed in

move person to fresh air. If in eyes, rinse with water for

15 minutes. Obtain medical attention. If on skin, rinse

well with water. If on clothes, removeclothes.

***Loctite® is a registered trademark of HenkelCorp.

Replacing the Profile (Fig. V)

To Change a Broken or Worn Profile

1. Refer to DCN6901 Return Spring Replacement Kit

Steps 1–4 to remove the return system from the unit

and to remove thesprings.

2. Take note of the orientation of the profile

. Slide the

profile off therails

Fig. V

ENGLISH

3. In the same orientation as the old profile, slide the new

profile onto therails.

4. Refer to DCN6901 Return Spring Replacement Kit

Steps 5–9 to complete theservice.

Repairs

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement, when

applicable) should be performed by a

DeWALT

factory

service center or a

DeWALT

authorized service center.

Always use identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to

faulty materials or workmanship for three years from

the date of purchase. This warranty does not cover part

failure due to normal wear or tool abuse. For further detail

of warranty coverage and warranty repair information,

visit www.dewalt.com or call 1-800-4-

DeWALT

(1-800-

433-9258). This warranty does not apply to accessories

or damage caused where repairs have been made

or attempted by others. THIS LIMITED WARRANTY IS

GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states do not allow

limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential

damages, so these limitations may not apply to you. This

warranty gives you specific legal rights and you may have

other rights which vary in certain states orprovinces.

In addition to the warranty,

DeWALT

tools are covered

byour:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,

DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204, DCB204BT, DCB205, DCB205BT, DCB206,

DCB606, DCB609

NOTE: Battery warranty voided if the battery pack is

tampered with in any way.

DeWALT

is not responsible

for any injury caused by tampering and may prosecute

warranty fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your

DeWALT

Power Tool, Laser, or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

(1-800-433-9258) for a freereplacement.

ENGLISH

TROUBLESHOOTING GUIDE

MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT

PROBLEMS, CONTACT A

DeWALT

SERVICE CENTER OR CALL 1-(800)-4-

DeWALT



WARNING: To reduce the risk of serious personal injury, ALWAYS disconnect battery pack from tool before

allrepairs.

SYMPTOM CAUSE FIX

Motor does not run with

trigger depressed

Trigger lock in locked position. Unlock trigger lock.

Tool is stalled, locking the motor from rotating. Rotate the stall release lever on the tool and the mechanism

will release. If driver blade does not return, remove battery and

manually push driver blade back to home position.

Tool is in the sequential actuation mode. Depress contact trip first before firing or switch to bump mode.

Tool internal electronics need to be reset. Remove battery, wait 3 seconds and reinsert.

Motor stops running after 5 seconds. Normal operation, release trigger and redepress.

Terminals are dirty or damaged. See authorized service center.

Damaged internal electronics. See authorized service center.

Damaged trigger. See authorized service center.

Motor does not run with contact

trip depressed

Trigger lock in locked position. Unlock trigger lock.

Dryfire lock out engaged, blocking contact trip

from traveling fully.

Load more nails into magazine.

Tool is stalled, locking the motor from rotating. Rotate the stall release lever on the tool and the mechanism

will release. If driver blade does not return, remove battery and

manually push driver blade back to home position.

Bent contact trip. See authorized service center.

Motor stops running after 5 seconds. Normal operation, release contact trip and redepress.

Terminals are dirty or damaged. See authorized service center.

Damaged internal electronics. See authorized service center.

Damaged trigger. See authorized service center.

Tool does not actuate (motor runs

but will not fire)

Dryfire lock out engaged, blocking contact trip

from traveling fully.

Load nails into magazine.

Low battery charge or damaged battery. Check charge level if pack shows state-of-charge. Charge or

replace battery pack if necessary.

Jammed nail/drive blade not returned to

home position.

Remove battery, clear jammed nail, cycle stall release

lever, (push driver blade up manually if necessary) reinsert

battery pack.

Damaged or worn return springs. Replace springs. Refer to DCN6901 Return Spring

Replacement Kit or see authorized service center.

Damaged or worn profile. Replace profile. Refer to Replacing the Profile or see

authorized service center.

Jammed internal mechanism. See authorized service center.

Damaged internal electronics. See authorized service center.

Motor starts up but generates a

lot of noise

Jammed nail and driver blade is stuck in

down position.

Use stall release lever, clear and jammed nails, and return

driver blade manually if necessary.

Damaged or worn return springs. Replace springs. Refer to DCN6901 Return Spring

Replacement Kit or see authorized service center.

Damaged or worn profile. Replace profile. Refer to Replacing the Profile or see

authorized service center.

ENGLISH

SYMPTOM CAUSE FIX

Drive blade continues to get stuck in

down position

Jammed nail and driver blade is stuck in

down position.

Use stall release lever, clear any jammed nails, and return

driver blade manually if necessary.

Damaged or worn return springs. Replace springs. Refer to DCN6901 Return Spring

Replacement Kit or see authorized service center.

Damaged or worn profile. Replace profile. Refer to Replacing the Profile or see

authorized service center.

Debris in nosepiece. Clean nose area and watch closely for small pieces of broken

nails stuck in the track.

Tool operates but does not drive

fasteners fully

Depth adjust set too shallow. Rotate depth adjust to a deeper setting.

Tool not firmly applied to workpiece. Apply adequate force to tool securing it tightly to workpiece

See instruction manual.

Material and fastener length. If the unit continues to stall (forcing the need to rotate the stall

release lever) choose the appropriate material and fastener

length that is not too rigorous of an application.

Damaged or worn profile. Replace profile. Refer to Replacing the Profile or see

authorized service center.

Damaged actuation mechanism. See authorized service center.

Tool operates, but no fastener

is driven

No nails in magazine. Load nails in magazine.

Wrong size or angle nails. Use only the recommended nails Refer to Nail Specifications.

Debris in nosepiece. Clean nose area and watch closely for small pieces of broken

nails stuck in the track.

Debris in magazine. Clean magazine.

Worn magazine. Replace magazine. See authorized service center.

Damaged or worn return springs. Replace springs. Refer to DCN6901 Return Spring

Replacement Kit or see authorized service center.

Damaged or worn profile. Replace profile. Refer to Replacing the Profile or see

authorized service center.

Jammed nail Wrong size or angle nails. Use only the recommended nails. Refer to Nail Specifications.

Magazine screws not secured after previous jam

clear/inspection.

Make sure to tighten magazine hex bolts with hex

wrench provided.

Material and fastener length. If the unit continues to stall (forcing the need to rotate the stall

release lever) choose the appropriate material and fastener

length that is not too rigorous an application.

Debris in nosepiece. Clean nose area and watch closely for small pieces of broken

nails stuck in the track.

Worn magazine. Replace magazine. See authorized service center.

Damaged or worn return springs. Replace springs. Refer to DCN6901 Return Spring

Replacement Kit or see authorized service center.

Damaged or worn profile. Replace profile. Refer to Replacing the Profile or see

authorized service center.

La page charge ...

DeWalt DCN21PLB Manuel utilisateur

Marque: DeWalt

Modèle: DCN21PLB

Catégorie: Cloueuse

Taper: Manuel utilisateur

Ce manuel convient également à

DCN21PLM1

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCN21PLB User manual
español: DeWalt DCN21PLB Manual de usuario

Documents connexes

Autres documents

Crafstman CMCN621PLB Le manuel du propriétaire