Bradley TDB3108 Manuel utilisateur

Installation

Instalación

TDB3108

Terreon

®

54" Circular Deep Bowl Washfountain with

Infrared Control

Terreon

®

Lavabo fontaine 1372 mm (54") à cuvette

profonde circulaire avec commande à infrarouge

Fuente de lavado circular con palangana profunda

Terreon

®

de 1372 mm (54") con control infrarrojo

WF3208

Terreon

®

Extra Height 54" Circular Classic

Washfountain with 9" Deep Bowl and Infrared Control

Terreon

®

Lavabo fontaine 1372 mm (54") à hauteur

supplémentaire classique circulaire à cuvette

profonde de 229 mm (9") et commande à infrarouge

Fuente de lavado clásica circular Terreon

®

de altura

adicional de 1372 m (54") con palangana profunda de

229 mm (9") y control infrarrojo

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 1-800-BRADLEY Fax: (262) 251-5817

http:\\www.bradleycorp.com

215-1187 Rev N; EN 06-915B

Page 1 of 85 4/6/2007

IMPORTANT!

Read this entire installation manual to ensure

proper installation. When finished with the

installation, file this manual with the owner

or maintenance department.

Separate parts from packaging and make

sure all parts are accounted for before

discarding any packaging material. If any

parts are missing, do not begin installation

until you obtain the missing parts.

Make sure that all water supply lines have

been flushed and then completely turned off

before beginning installation. Debris in

supply lines can cause valves to

malfunction.

Hardware supplied by installer must be

appropriate for wall construction. Wall

anchors used must have a minimum pull-out

rating of 1,000 lbs.

The Adaptive® Infrared control must be

connected with a 24 VAC Class II

transformer. Connections to 110 VAC can

cause personal injury and will result in

damage to the electronics.

Product warranties may be found under

“Product Information” on our web site at

www.bradleycorp.com.

IMPORTANT !

Lire ce manuel d’installation dans son

intégralité pour garantir une installation

appropriée. Une fois celle-ci terminée,

classer ce manuel auprès du service à la

clientèle ou d’entretien.

Séparer les pièces de l’emballage et veiller à

bien avoir toutes les pièces avant de jeter le

matériau d’emballage. Le cas échéant, ne

pas commencer l’installation avant d’avoir

obtenu les pièces manquantes.

Veiller à bien vidanger et fermer toutes les

conduites d’eau avant de commencer

l’installation. Tout débris dans les conduites

d’alimentation risque de provoquer un

mauvais fonctionnement des soupapes.

La quincaillerie fournie par l’installateur doit

être appropriée pour la construction des

murs. Les dispositifs d’ancrage muraux

doivent avoir un indice d’arrachement

minimum de 454 kg (1 000 lbs.).

La commande à infrarouge Adaptive® doit

être connectée avec un transformateur

24 V c.a. Classe II. Des connexions à du

110 V c.a. peuvent provoquer des blessures

personnelles et endommager les

composants électroniques.

Les garanties du produit figurent sous la

rubrique « Informations techniques » sur

notre site Internet à www.bradleycorp.com.

¡IMPORTANTE!

Lea todo este manual para garantizar su

instalación adecuada. Cuando haya

terminado la instalación, preséntelo al dueño

o al Departamento de Mantenimiento.

Separe las piezas del empaque y asegúrese

de que no falte ninguna antes de desechar el

material del empaque. Si falta alguna pieza,

no comience con la instalación hasta que

obtenga las faltantes.

Asegúrese de que todas las tuberías de

suministro de agua hayan sido lavadas y

cerradas completamente antes de comenzar

la instalación. Los desechos en las tuberías

de suministro pueden causar averías en las

válvulas.

Las piezas metálicas proporcionadas por el

instalador deben ser adecuadas para la

construcción en la pared. Las sujeciones de

pared usadas deben tener una capacidad

mínima de extracción de 454 kg (1.000

libras).

El control infrarrojo Adaptive® debe

conectarse con un transformador clase II de

24 V CA. Las conexiones a 110 V CA pueden

causar lesiones personales y producirán

daños a los componentes electrónicos.

Se pueden encontrar garantías de los

productos en Product Information

(Información sobre productos) en nuestro

sitio Web en www.bradleycorp.com.

A

D

A

C

O

M

P

L

I

A

N

T

TDB3108

with Infrared Control

TDB3108

avec commande à infrarouge

Modelo TDB3108

con control infrarrojo

TDB3108 Juvenile

with Infrared Control

TDB3108 Enfant

avec commande à infrarouge

Modelo infantil TDB3108

con control infrarrojo

WF3208

with Infrared Control

WF3208

avec commande à infrarouge

Modelo WF3208

con control infrarrojo

TDB3108 TAS Height

with Infrared Control

TDB3108 Hauteur TAS

avec commande à infrarouge

Altura TAS del modelo TDB3108

con control infrarrojo

TDB3108, WF3208 Terreon

®

54" Circular Installation

2 4/6/2007 Bradley Corporation • 215-1187 Rev. N; EN 06-915B

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Model TDB3108 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Model WF3208 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Washfountain Rough-Ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-19

Terreon® Cleaning/Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Gel-Coated Fiberglass Cleaning/Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Stainless Steel Cleaning/Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Soap Dispensing Valve Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-23

Soap Recommendations and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Sprayhead Troubleshooting/Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Manual Mixing Valve (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Volume Control Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Vernatherm™ Thermostatic Mixing Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28-29

Supplies Required by Installer

• (4) 1/2" lag bolts, screws or other fasteners to anchor washfountain pedestal

• 1" hot and cold water supply lines and fittings (refer to rough-ins on pages 7-8)

• Reducing fittings and 1/2" nom. copper tubing supply lines for types with supplies from above

• Standard P-trap (refer to rough-ins on pages 7-8) (vented trap supplied by Bradley when required)

• 2" drain lines and fittings (refer to rough-ins on pages 7-8)

• 1-1/2" vent or tie pipe on fixtures vented through washfountain column (see page 9 for lengths required)

• Teflon tape or pipe dope

• 110 VAC GFI power source for 110/24 VAC UL Class II transformer supplied

• OPTIONAL: Bradley recommends installing an electrical cut-off switch to the unit. This feature

allows no accidental water delivery during regular maintenance and service.

Pre-Installation Information

Terreon

®

Material

The Washfountain is constructed of Terreon

®

, a densified solid surface material composed of polyester

resin. Terreon

®

is resistant to chemicals, stains, burns and impact. Surface damage can be easily

repaired with everyday cleaners or fine-grit abrasives. Terreon

®

is NAHB certified to meet ANSI

Z124.3, Z124.6 and ANSI/ICPA SS-1-2001.

Adaptive Infrared

The sprayhead is controlled by a solenoid valve, allowing the user to activate a flow of water. The

Infrared sensor will take a few minutes to adapt to its environment when the unit is powered up.

Installation TDB3108, WF3208 Terreon

®

54" Circular

3Bradley Corporation • 215-1187 Rev. N; EN 06-915B 4/6/2007

A

D

A

•

C

O

M

P

L

I

A

N

T

54"

(1372)

19-1/2"

(495)

36"

(914)

23-1/2"

(597)

10"

(254)

34"

(864)

43-3/4"

(1111)

47-1/4"

(1200)

Model TDB3108 is ADA compliant.

Optional equipment may not comply with

all ADA dimensional guidelines

Model TDB3108 - 54" Circular

with optional accessories

Figure 1a

63-5/8"

(1616)

WITH

SOAP

55-1/8"

(1400)

WITHOUT

SOAP

54"

(1372)

36"

(914)

19-1/2"

(495)

55-3/4"

(1416)

47-1/4"

(1200)

43-3/4"

(1111)

34"

(864)

23-1/2"

(597)

10"

(254)

6" (152)

Adjust to towel dispenser

mounting holes

Figure 1b

TDB3108, WF3208 Terreon

®

54" Circular Installation

4 4/6/2007 Bradley Corporation • 215-1187 Rev. N; EN 06-915B

Circular Washfountain Dimensions (TAS intermediate)

61"

(1549)

WITH

SOAP

52-1/2"

(1334)

WITHOUT

SOAP

54"

(1372)

35-1/2"

(902)

19-1/2"

(495)

53-1/4"

(1353)

44-5/8"

(1143)

41-1/8"

(1045)

32"

(813)

25-1/2"

(648)

12"

(305)

6" (152)

Adjust to towel dispenser

mounting holes

TAS

54"

(1372)

19-1/2"

(495)

35-1/2"

(902)

25-1/2"

(648)

12"

(305)

32"

(813)

41-1/8"

(1045)

44-5/8"

(1133)

Model TDB3108

54" Circular - TAS Height

Model TDB3108

54" Circular - TAS Height with

optional accessories

Figure 1c

Figure 1d

Optional equipment may not comply with

all TAS dimensional guidelines

Installation TDB3108, WF3208 Terreon

®

54" Circular

5Bradley Corporation • 215-1187 Rev. N; EN 06-915B 4/6/2007

Circular Washfountain Dimensions (juvenile height)

59-1/8"

(1502)

WITH

SOAP

50-5/8"

(1286)

WITHOUT

SOAP

54"

(1372)

35-1/2"

(902)

19-1/2"

(495)

51-1/4"

(1303)

42-5/8"

(1033)

39-1/8"

(994)

30"

(762)

23-1/2"

(597)

10"

(254)

6" (152)

Adjust to towel dispenser

mounting holes

A

D

A

•

C

O

M

P

L

I

A

N

T

Optional equipment may not

comply with all ADA

dimensional guidelines

A

D

A

•

C

O

M

P

L

I

A

N

T

54"

(1372)

19-1/2"

(495)

35-1/2"

(902)

23-1/2"

(597)

10"

(254)

30"

(762)

39-1/8"

(994)

42-5/8"

(1083)

Model TDB3108

54" Circular - Juvenile Height

Model TDB3108

54" Circular - Juvenile Height

with optional accessories

Figure 1e

Figure 1f

Optional equipment may not comply with

all ADA or TAS dimensional guidelines

TDB3108, WF3208 Terreon

®

54" Circular Installation

6 4/6/2007 Bradley Corporation • 215-1187 Rev. N; EN 06-915B

Circular Washfountain Dimensions

63-5/8"

(1616)

WITH

SOAP

55-1/8"

(1400)

WITHOUT

SOAP

54"

(1372)

37-1/2"

(953)

19-1/2"

(495)

55-3/4"

(1416)

47-1/4"

(1200)

43-3/4"

(1111)

34"

(864)

23-1/2"

(597)

10"

(254)

6" (152)

Adjust to towel dispenser

mounting holes

54"

(1372)

19-1/2"

(495)

37-1/2"

(953)

23-1/2"

(597)

10"

(254)

34"

(864)

43-3/4"

(1111)

47-1/4"

(1200)

Model WF3208 is not ADA compliant.

Model WF3208 - 54" Circular

with optional accessories

Figure 1g

Figure 1h

Installation TDB3108, WF3208 Terreon

®

54" Circular

7Bradley Corporation • 215-1187 Rev. N; EN 06-915B 4/6/2007

Rough-In Specifications

NOTE: Supply lines for one to two

washfountains should be 1"; for

three washfountains, 1-1/4". For

more than three washfountains,

pipe sizes should be increased

proportionately.

NOTE: Supply lines for one to two

washfountains should be 1"; for

three washfountains, 1-1/4". For

more than three washfountains,

pipe sizes should be increased

proportionately.

Figure 2a

Figure 2b

TDB3108, WF3208 Terreon

®

54" Circular Installation

8 4/6/2007 Bradley Corporation • 215-1187 Rev. N; EN 06-915B

Rough-In Specifications continued . . .

NOTE: Supply lines for one to two

washfountains should be 1"; for

three washfountains, 1-1/4". For

more than three washfountains,

pipe sizes should be increased

proportionately.

NOTE: Supply lines for one to two

washfountains should be 1"; for

three washfountains, 1-1/4". For

more than three washfountains,

pipe sizes should be increased

proportionately.

Figure 2c

Figure 2d

Installation TDB3108, WF3208 Terreon

®

54" Circular

9Bradley Corporation • 215-1187 Rev. N; EN 06-915B 4/6/2007

1

Installing the drain

NOTE:

All piping shown in dotted lines

to be supplied by installer.

ROUGH IN SUPPLY AND DRAIN PIPING AS REQUIRED FOR YOUR INSTALLATION (SEE

PAGES 7-8 FOR ROUGH-INS OF OPTIONAL INSTALLATIONS)

A

ASSEMBLE THE DRAIN TO THE DIMENSION SHOWN IN FIGURE 3 FOR THE BOWL

YOU ARE INSTALLING.

B

Centerline of

Washfountain

Centerline of

Washfountain

Centerline of

Washfountain

See rough-ins

on Pages 7-8

for dimensions

not shown

Types B, H

Types A, O

With Tie Pipe

Bracket Option

Types A, O

2" NPT Coupling if Tie

Pipe is not required

(Supplied by Installer)

Vent

or

Tie Pipe

(Supplied by Installer)

Vent

or

Tie Pipe

(Supplied by Installer)

Vented Trap

(111-024)

Optional

Tie Pipe Bracke

t

(S70-082)

4"

(102)

4"

(102)

B – See Table 1

4"

(102)

Figure 3

Dim Standard Height Juvenile Height TAS

B 23-3/8" (594mm) 22-1/2" (572mm) 24-1/2" (622mm)

Table 1 — “B” Trap Dimensions

TDB3108, WF3208 Terreon

®

54" Circular Installation

10 4/6/2007 Bradley Corporation • 215-1187 Rev. N; EN 06-915B

2

Bowl/pedestal mounting and assembly

CAUTION:

Bowl surface is very smooth. Approximate

weight of bowl is 190 pounds. Handle with Care!

POSITION THE PEDESTAL AT DESIRED LOCATION AND MARK THE POSITION OF THE (4) MOUNTING LOCATIONS (SEE FIGURE 4A).

PLACE TAS SPACER ON FLOOR OVER THE MOUNTING HOLES. PLACE PEDESTAL ON TOP OF THE SPACER.

A

SECURE PEDESTAL TO FLOOR WITH SUITABLE FASTENERS, 1/2" ANCHORS AND BOLTS (SUPPLIED BY INSTALLER). DO NOT OVERTIGHTEN.

B

USING THREE OR FOUR PEOPLE, CAREFULLY LIFT BOWL (SEE FIGURE 4B) ON TO PEDESTAL MAKING SURE DRAIN

HOLES LINE UP WITH FLOOR DRAIN AND MATE THREAD RODS WITH SLOTTED HOLES IN PEDESTAL USING

LOCATOR RIBS.

C

TAS OPTION:

USING 1/4" WING NUTS AND WASHERS, SECURE THE BOWL TO THE

PEDESTAL IN FOUR PLACES.

D

DRAIN

TOP VIEW

FRONT VIEW

TDB 3108 BOWL - 190 LBS.

THREADED RODS

(4) PLACES

LOCATOR RIBS

(4) PLACES

1/4" WASHERS

AND WING NUTS

(4) PLACES

THREADED RODS

(4) PLACES

FLOOR MOUNTING

(4) PLACES

DRAIN

PLACE HANDS

HERE WHEN

LIFTING BOWL

PLACE HANDS

HERE WHEN

LIFTING BOWL

Figure 4a

Figure 4b

Installation TDB3108, WF3208 Terreon

®

54" Circular

11Bradley Corporation • 215-1187 Rev. N; EN 06-915B 4/6/2007

3

Installing drain spud in bowl

NOTE!

Seal between drain spud and drain hole with

plumber’s putty (supplied by installer).

LOOSELY ATTACH THE DRAIN SPUD TO THE BOWL WITH THE

LOCKNUT AND WASHER AS SHOWN IN FIGURE 5.

A

TIGHTEN THE SPUD AND LOCK NUT AGAINST THE BOWL.

B

SECURE THE STRAINER TO DRAIN SPUD WITH THE SCREWS PROVIDED.

C

CONNECT SPUD (OR B TRAP OR TIE PIPE BRACKET) TO DRAIN.

D

ATTACH B TRAP TO DRAIN SPUD.

B TRAP OPTION:

ATTACH TIE PIPE BRACKET TO

DRAIN SPUD.

TIE PIPE OPTION:

STRAINER

S45-067

SPUD

112-015

BOWL

WASHER

142-068

LOCKNUT

161-021

DRAIN PRE-PACK

S45-273

Figure 5

TDB3108, WF3208 Terreon

®

54" Circular Installation

12 4/6/2007 Bradley Corporation • 215-1187 Rev. N; EN 06-915B

Adaptive infrared assembly for A drain and O drain units

without Tie Pipe option

4a

SUPPORT TUBE

GASKET

125-011

SUPPORT TUBE

(STD) S57-005

(JUV) S57-006

TIE ROD PRE-PACK

S45-1336

1/2" SUPPLY TUBE

PRE-PACK

S45-1466

PRE-PACK

S45-055

TIE BAR

PEDESTAL ASSY.

S17-242

COVER

107-099 (A)

107-179 (O)

I.R. MODULE ASSY.

S50-344

SPRAYHEAD

S05-054

TIE ROD

176-008A

DRAIN

S45-273

VALVE ASSY.

S50-369

ACCESS PANEL

186-1456

TERREON® DEEP BOWL

(ADA bowl shown, classic

bowl is optional)

Part No. varies with color of bowl.

Contact your local Bradley Rep.

for assistance

NUT

A/O

(A shown)

COVER

TIE ROD

PRE-PACK

TIE

ROD

COUPLING

NUT

SECTION VIEW OF

A/O UNIT ASSEMBLY

SPRAYHEAD

ACTUATOR

MODULE

ASSY.

TIE

BAR

SUPPLY TUBE

Figure 6

INSTALL HEMMED END (NOT SHARP END) OF SUPPORT TUBE WITH GASKET ONTO BOWL (SEE FIGURE 6).

A

CONNECT 1/2" SUPPLY TUBING TO SPRAYHEAD WITH 3/8" NPT TO 1/2" TUBE CONNECTOR AND PLACE SPRAYHEAD ONTO

SUPPORT TUBE. RUN THE TUBING DOWN THROUGH THE SUPPORT TUBE AND CONNECT TO VALVE TUBE CONNECTOR.

B

PLACE THE UPPER TIE BAR (NOTCHED AT BOTH CORNERS OF EACH END) ON TOP OF SPRAYHEAD. CONNECT THE LONGER TIE

ROD TO THE 4-1/4" TIE ROD USING THE COUPLING NUT WITH HEX HEAD SET SCREWS. RUN THE TIE ROD ASSEMBLY DOWN

THROUGH UPPER TIE BAR (SEE FIGURE 6 INSET) AND SECURE FROM UNDERNEATH THE BOWL USING LOWER TIE BAR (NO

NOTCHES) AND HEX NUT WITH SOCKET HEAD SET SCREW.

C

Installation TDB3108, WF3208 Terreon

®

54" Circular

13Bradley Corporation • 215-1187 Rev. N; EN 06-915B 4/6/2007

Installation Instructions continued . . .

TOP COVER

Figure 7

I.R. MODULE

ASSEMBLY

S50-344

SPRAYHEAD

S05-054

SUPPORT TUBE

(STD.) S57-005

(JUV.) S57-006

COUPLING

NUT

SPACER

SOAP

DISPENSER

TIE ROD

(STD.) 21-5/8"

(JUV.) 18-1/8"

UNIT WITH “A” DRAIN AND I.R. MODULE

SHOWN, ALSO AVAILABLE WITH “O” DRAIN

COUPLING

NUT

4-1/4"

TIE ROD

8-5/8"

TIE ROD

MODULE

COVER

TIE BAR

PLACE THE INFRARED MODULE ASSEMBLY ON TOP OF SPRAYHEAD. ROTATE UNTIL INFRARED MODULE LOCKS IN WITH TIE BAR.

DROP TWO INFRARED MODULE WIRES DOWN TO VALVE ASSEMBLY.

D

SECURE INFRARED MODULE COVER AND TOP COVER WITH ACORN NUT AND SET SCREW.

E

FOR O UNIT: INSTALL 1/2" NOMINAL COPPER TUBING SUPPLY LINES (PASS THEM THROUGH HOLES IN COVER DOWN

THROUGH SUPPORT COLUMN) AND CONNECT TO STOPS USING SUITABLE FITTINGS.

F

FOR UNITS WITH SOAP OPTION, INSTALL THE SPACER, SOAP DISPENSER AND COVER USING THE THIRD TIE ROD (8-5/8" LONG)

AND SECOND COUPLING NUT AS SHOWN (SEE FIGURE 7). SECURE WITH ACORN NUT AND SET SCREW.

•

NOTE! Skip to step E for units without soap.

TDB3108, WF3208 Terreon

®

54" Circular Installation

14 4/6/2007 Bradley Corporation • 215-1187 Rev. N; EN 06-915B

Adaptive infrared assembly for B drain and H drain units

with Tie Pipe option

4b

SUPPORT TUBE

GASKET

125-011

SUPPORT TUBE

(STD) S57-005

(JUV) S57-006

PRE-PACK

S45-1466

VENTED TRAP

111-024

TIE BAR

PRE-PACK

S45-056

PEDESTAL ASSY.

S17-242

COVER

107-185 (B)

107-048 (H)

I.R. MODULE ASSY.

S50-344

1/2" SUPPLY TUBE

SPRAYHEAD

S05-054

DRAIN

S45-273

VALVE ASSY.

S50-369

ACCESS PANEL

186-1456

TERREON® DEEP BOWL

(ADA bowl shown, classic bowl

is optional) Part No. varies with color

of bowl. Contact your Bradley Rep.

for assistance.

B/H

(B shown)

COVER

SECTION VIEW OF

B/H UNIT ASSEMBLY

SPRAYHEAD

ACTUATOR

MODULE

ASSY.

TIE

BAR

SUPPLY

TUBE

Figure 8

INSTALL HEMMED END (NOT SHARP END) OF SUPPORT TUBE WITH GASKET ONTO BOWL (SEE FIGURE 8).

A

CONNECT 1/2" SUPPLY TUBING TO SPRAYHEAD WITH 3/8" NPT TO 1/2" TUBE CONNECTOR AND PLACE SPRAYHEAD ONTO

SUPPORT TUBE. RUN THE TUBING DOWN THROUGH THE SUPPORT TUBE AND CONNECT TO VALVE TUBE CONNECTOR.

B

INSERT THE 1-1/2" VENT PIPE (SUPPLIED BY INSTALLER) DOWN THROUGH THE SUPPORT TUBE AND THREAD INTO VENTED TRAP.

C

Installation TDB3108, WF3208 Terreon

®

54" Circular

15Bradley Corporation • 215-1187 Rev. N; EN 06-915B 4/6/2007

Installation Instructions continued . . .

Figure 9

INFRARED

MODULE

ASSEMBLY

S50-344

SPRAYHEAD

S05-054

SUPPORT TUBE

(STD.) S57-005

(JUV.) S57-006

SPACER

SOAP

DISPENSER

TIE BAR

UNIT WITH “B” DRAIN AND I.R. MODULE

SHOWN, ALSO AVAILABLE WITH “H” DRAIN

TOP COVER

PLACE THE INFRARED MODULE ASSEMBLY ON TOP OF SPRAYHEAD. ROTATE UNTIL INFRARED MODULE LOCKS IN WITH TIE BAR.

DROP TWO INFRARED MODULE WIRES DOWN TO VALVE ASSEMBLY.

D

POSITION THE UPPER TIE BAR SLIGHTLY BELOW THE MODULE (SEE FIGURE 8 INSET ON PREVIOUS PAGE) OR SOAP DISPENSER

(SEE FIGURE 9) AND FASTEN SECURELY TO VENT PIPE WITH SET SCREWS PROVIDED. SECURE TOP COVER TO TIE BAR WITH TWO

CAP SCREWS PROVIDED.

E

FOR B UNIT: INSTALL 1/2" NOMINAL COPPER TUBING SUPPLY LINES (PASS THEM THROUGH HOLES IN COVER DOWN

THROUGH SUPPORT COLUMN) AND CONNECT SUPPLY LINES TO STOPS USING SUITABLE FITTINGS.

F

FOR UNITS WITH SOAP OPTION, SLIDE THE SPACER AND SOAP DISPENSER OVER THE 1-1/2" PIPE.

•

NOTE! Skip to step E for units without soap.

TDB3108, WF3208 Terreon

®

54" Circular Installation

16 4/6/2007 Bradley Corporation • 215-1187 Rev. N; EN 06-915B

5

Valve and tubing connections

TEE

269-764

VOLUME CONTROL

S02-045

THERMOSTATIC

MIXING VALVE

ASSEMBLY

S67-597

STOP/CHECK

VALVE

1/2" DIA. TUBE

FROM SPRAYHEAD

1/2" DIA. TUBE

R68-600012

SOLENOID

ASSY.

S08-055

FLEXIBLE

HOSE

FILTER WASHER

Figure 10a

Figure 10b

NUT

MALE TUBE

CONNECTOR

TUBING

VALVE ASSEMBLY S50-369

NOTE: Flush supply lines before making connections.

Do not apply pipe sealant to compression fittings.

CONNECT 1/2" DIA. TUBING TO TEE AND SOLENOID ASSEMBLY, TWO PLACES. THE MALE CONNECTOR

(FIGURE 10B) FOR THE VALVE ASSEMBLY WILL REMAIN TIGHT AND LEAKPROOF WHEN TUBING IS CUT AND INSTALLED PROPERLY.

FOLLOW THE PROCEDURES BELOW WHEN INSTALLING TUBING TO ENSURE THAT YOU ACHIEVE A LEAKPROOF SEAL.

A

USING A SHARP RAZOR, CUT TUBING SQUARELY AND REMOVE ANY BURRS. DO NOT PINCH OR CRUSH END OF TUBING.

•

LOOSEN NUT ON FITTING. MOISTEN END OF TUBE AND PUSH INTO FITTING UNTIL IT IS FIRMLY SEATED. TIGHTEN NUT TO SECURE

TUBE TO FITTING (MAKE SURE NUT IS SECURELY TIGHTENED).

•

IF CONNECTOR LEAKS, RESEAT TUBING ACCORDING TO ABOVE PROCEDURE. IF LEAKING PERSISTS, REPLACE MALE

CONNECTOR, OR CALL YOUR BRADLEY REPRESENTATIVE FOR ASSISTANCE.

•

HANG VALVE ASSEMBLY ON PEDESTAL BRACKET (SEE FIGURE 11 ON PAGE 17). USE WIRE TIE TO SECURE VALVES.

B

CONNECT THE 1/2" NPT FEMALE END OF THE STOP/CHECK VALVES TO THE ROUGH-INS.

C

ATTACH FLEXIBLE HOSING TO THERMOSTATIC MIXING VALVE, TWO PLACES.

D

INSERT THE FILTER WASHERS (PROVIDED) INTO THE SWIVEL NUT AT THE END OF THE SUPPLY HOSES AND CONNECT TO THE

STOP/CHECK VALVES.

E

NOTE! For “O” and “B” units (overhead supplies) Skip steps C through E

Installation TDB3108, WF3208 Terreon

®

54" Circular

17Bradley Corporation • 215-1187 Rev. N; EN 06-915B 4/6/2007

Installation Instructions continued . . .

VALVE AND TUBING CONNECTIONS - ADAPTIVE INFRARED OPTION

NOTE: FLUSH SUPPLY LINES BEFORE MAKING CONNECTIONS.

1/2" TUBE FROM

SPRAYHEAD

VOLUME

CONTROL

CHECK/STOP

VALVE

BRACKET

PEDESTAL

FILTER

WASHER

COLD

SUPPLY

HOT

SUPPLY

Figure 11

TDB3108, WF3208 Terreon

®

54" Circular Installation

18 4/6/2007 Bradley Corporation • 215-1187 Rev. N; EN 06-915B

6

Electrical connections for Adaptive Infrared

START-UP NOTE: Do not use for two minutes after making power connection. The sensors will take up

to eight minutes (without being used) to adapt to the bowl if another object is detected during the

two-minute start-up period.

I.R. MODULE

S50-344

TOP VIEW MODULE

ASSEMBLY

CONNECT WIRES

AS SHOWN

VALVE ASSY.

S50-369

110/24 VAC

TRANSFORMER

S83-134

F = FEMALE CONNECT

M = MALE CONNECT

WIRE

ADAPTER

269-620

S53-261

(S53-261A) C

RED

(S53-261A) A

RED

(S53-272) B

BLACK

WINDOW

269-1351

Figure 12

CONNECT THE THREE WIRES FROM THE INFRARED MODULE ASSEMBLY TO THE VALVE ASSEMBLY. ATTACH TWO OF THE FEMALE

CONNECT WIRES TO THE SOLENOIDS AS SHOWN IN FIGURE 12. ATTACH THE MALE CONNECT WIRE TO ONE OF THE 24 VAC

TRANSFORMER LEADS. ATTACH THE REMAINING TRANSFORMER LEAD TO THE SOLENOID WIRE ADAPTER (SEE FIGURE 12).

A

CONNECT 24 VAC TRANSFORMER PROVIDED TO POWER SOURCE.

B

TURN SUPPLIES ON. OPEN CHECK/STOP VALVES COMPLETELY.

C

OPEN VOLUME CONTROL VALVE COMPLETELY AND CHECK PIPING INSTALLATION FOR LEAKS.

D

PASS YOUR HAND IN FRONT OF EACH SENSOR UNTIL AIR IS PURGED FROM THE LINES.

E

Installation TDB3108, WF3208 Terreon

®

54" Circular

19Bradley Corporation • 215-1187 Rev. N; EN 06-915B 4/6/2007

Vernatherm Ajustment Instructions

NOTE: The Vernatherm TMA valve is NOT factory preset. Upon installation, the temperature

of this valve must be checked and adjusted to ensure delivery of a safe water temperature.

Water in excess of 110°F (43°C) may cause scalding.

TEMPERATURE

ADJUSTMENT

STEM

TEMPERATURE

LOCKING

NUT

Figure 13

CHECK THE TEMPERATURE AND ADJUST IF NECESSARY (THE RANGE OF THE VALVE IS 95°F–115°F (35°C–43°C). TO ADJUST THE

TEMPERATURE, FOLLOW THE PROCEDURE BELOW:

F

CLEAN SPRAYHEAD IF NECESSARY. SEE PAGE 25 FOR SPRAYHEAD MAINTENANCE AND REPAIR PARTS. ADJUST THE VOLUME

CONTROL VALVE, IF NECESSARY, TO CONTROL THE FLOW OF WATER.

G

ATTACH PEDESTAL ACCESS PANEL WITH HARDWARE PROVIDED.

H

ATTACH KICK PLATE TO PEDESTAL BASE WITH HARDWARE PROVIDED.

I

LOOSEN TEMPERATURE LOCKING NUT WITH WRENCH.

•

ONCE DESIRED TEMPERATURE IS REACHED, TIGHTEN NUT TO PREVENT TEMPERATURE CHANGE.

•

USING A BLADE SCREWDRIVER, TURN THE ADJUSTMENT STEM COUNTERCLOCKWISE TO INCREASE THE TEMPERATURE OR

CLOCKWISE TO DECREASE THE TEMPERATURE (FIGURE 13).

•

TDB3108, WF3208 Terreon

®

54" Circular Installation

20 4/6/2007 Bradley Corporation • 215-1187 Rev. N; EN 06-915B

Cleaning/Maintenance Instructions for Terreon®

Material Description: Terreon

®

is a NAHB Certified densified solid surface material composed of polyester

resin and is resistant to chemicals, stains, burns and impact. Surface damage can be easily repaired with

everyday cleansers or fine grit abrasives.

Routine Cleaning: Clean daily or as often as conditions require using a standard commercial or household

cleaner such as Formula 409

®

or Windex

®

.

Stubborn Stains: Remove tough stains with Ajax

®

, Comet

®

, or Soft-Scrub

®

and a green Scotch-Brite

®

pad or

lightly sand in a circular motion with 240 grit wet/dry sandpaper. The finish can be renewed with a maroon

Scotch-Brite pad.

Special Situations for Material

Scratches: Remove scratches with a green Scotch-Brite

®

pad. The finish can then be renewed with a maroon

Scotch-Brite

®

pad.

Hard Water Deposits: Remove hard water deposits with a mild solution of vinegar and water. Always rinse

the unit thoroughly after cleaning.

Restoring the Surface: Use Hope’s

®

Solid Surface cleaner and polish to refresh and protect the Terreon

Solid Surface material. Bradley recommends additional care and maintenance for the darker colored Terreon,

for complete instructions on this additional maintenance see Bradley document #1505.

IMPORTANT:

DO NOT USE STRONG ACID OR ALKALINE CHEMICALS AND CLEANSERS TO

CLEAN TERREON. IF THESES CHEMICALS COME IN CONTACT WITH THE TERREON

SURFACE WIPE THEM OFF IMMEDIATELY AND RINSE WITH SOAPY WATER. AVOID CONTACT

WITH HARSH CHEMICALS SUCH AS PAINT REMOVER, BLEACH, ACETONE, ETC. AVOID

CONTACT WITH HOT PANS AND OBJECTS.

Repair Kits: Terreon

®

repair kits are available. Contact your Bradley representative or distributor for part

numbers and pricing.

NOTE: Repair kits are made to order and have a shelf life of 30 days.

Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an

endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products named

are regional in distribution, and can be found in local supermarkets, department and hardware stores, or

through your cleaning service. It is emphasized that all products should be used in strict accordance with

package instructions.

Cleaning/Maintenance Instructions for Gel-coated Fiberglass

Material Description: The Terreon

®

Washfountains referenced in this installation manual use a gel-coated

fiberglass pedestal.

Routine Cleaning: The gel-coated pedestal should be cleaned daily or as often as needed with a mild solution

of detergent and water. Always use a soft cloth to avoid damage to the finish.

Repair Kits: There are no repair kits available for fiberglass materials. However, replacement parts are

available, contact your Bradley representative for pricing and part numbers.

IMPORTANT: DO NOT EXPOSE GEL-COATED FIBERGLASS TO SOLVENTS AS THEY

WILL DAMAGE THE MATERIAL AND MAY CREATE HARMFUL FUMES.

Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an

endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products named are

regional in distribution, and can be found in local supermarkets, department and hardware stores, or through your

cleaning service. It is emphasized that all products should be used in strict accordance with package instructions.

La page charge ...

Bradley TDB3108 Manuel utilisateur

Ce manuel convient également à

Bradley TDB3108 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents