Greenlee 38568 - 43177 - 43178 Long Reach Chain Saws Manuel utilisateur

INSTRUCTION MANUAL

Español............................23

Français ..........................45

Read and understand all of the instructions and

safety information in this manual before operating

or servicing this tool.

Register this product at www.greenlee.com

38568, 43177, and 43178

Long-Reach Chain Saws

Serial Codes AMM, AMN, AMP, FRM, FRP, FRR, HAA, HAB, and HAC

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

2

Purpose

This manual is intended to familiarize all personnel with

the safe operation and maintenance procedures for the

following Greenlee hydraulic tools:

38568 Serial Codes AMM, FRM, and HAB

43177 Serial Codes AMN, FRP, and HAC

43178 Serial Codes AMP, FRR, and HAA

Keep this manual available to all personnel.

Replacement manuals are available upon request

at no charge at www.greenlee.com.

Other Publications

Tool Owners/Users

SAE Standard J1273 (Hose and Hose Assemblies):

Publication 99930323

Greenlee Authorized Service Centers

Repair Manual: Publication 99912864

All specications are nominal and may change as design

improvements occur. Greenlee Tools, Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

KEEP THIS MANUAL

Table of Contents

Description .................................................................... 2

Safety ............................................................................ 2

Purpose ......................................................................... 2

Other Publications ......................................................... 2

Important Safety Information .....................................3–6

Identication .................................................................. 7

Specications ................................................................ 8

Chain Saw Basics ....................................................9–11

Setting the Super Spool .............................................. 12

Hoses and Fittings ...................................................... 12

Hose Connections ....................................................... 12

Typical Setup ............................................................... 12

Operation ................................................................ 13–14

Maintenance ...........................................................15–19

Troubleshooting ......................................................20–21

Illustrations and Parts Lists ....................................67–76

Description

Long-reach chain saws are hydraulically powered

cutting tools intended for general tree trimming from the

ground or from an aerial device.

Greenlee ’s patented Super Spool™ design allows the

tool to be used with either open-center or closed-center

hydraulic systems. The dielectric properties of the ber-

glass pole reduce the chance of electric shock when

the saw is used near energized electrical lines. Other

features include an anti-kickback chain, a fully covered

sprocket guard, a hand-stop safety collar, a trigger inter-

lock and a trigger guard.

Super Spool is protected by U.S. Patent No. 4,548,229.

Safety

Safety is essential in the use and maintenance of

Greenlee tools and equipment. This instruction manual

and any markings on the tool provide information for

avoiding hazards and unsafe practices related to the

use of this tool. Observe all of the safety information

provided.

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

3

IMPORTANT SAFETY INFORMATION

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards

or unsafe practices which could result in an injury or

property damage. The signal word, dened below,

indicates the severity of the hazard. The message

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result

in severe injury or death.

Hazards which, if not avoided, COULD result in

severe injury or death.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

Read and understand all of the

instructions and safety information

in this manual before operating or

servicing this tool.

Failure to observe this warning could

result in severe injury or death.

Electric shock hazard:

• This tool was tested to meet

OSHA 1910.269 (dry test) when

manufactured. It must be properly

cleaned and maintained to ensure

continued non-conductive prop-

erties. When using this unit near

energized electrical lines, use only

certied non-conductive hoses

and proper personal protective

equipment.

• Keep berglass extension clean

and dry when working around

energized electrical lines.

Accumulated oil or dirt reduces the

insulating properties of the tool.

• When using this tool near ener-

gized electrical lines, observe the

instructions provided in DIN EN

50110-1. The signicant sections

of this standard are provided in the

Operation section of this manual.

Failure to observe these warnings

could result in severe injury or death.

Skin injection hazard:

Oil under pressure easily punctures

skin causing serious injury, gan-

grene or death. If you are injured by

escaping oil, seek medical attention

immediately.

• Do not use hands to check for

leaks.

• Do not hold hose or couplers while

the hydraulic system is pressurized.

• Depressurize the hydraulic system

before servicing.

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

4

Before operating the saw, read and

understand the following explana-

tions in this manual:

• Pull-In

Pull-in can occur when the blade

at the bottom of the bar contacts

a foreign object, such as a nail,

or when the blade is pinched

in the cut.

The saw will be suddenly and

forcefully pulled away from the

operator.

• Push-back

Push-back can occur when the

blade at the top of the bar contacts

a foreign object, such as a nail, or

when the blade is pinched in the

cut.

The saw will be suddenly and

forcefully pushed back toward the

operator.

• Kickback

Kickback can occur when the

chain at the guide bar tip contacts

anything. The bar of the saw will

travel upward and back, toward the

operator.

Failure to observe this warning could

result in severe injury or death.

Wear a hard hat when using this tool.

Failure to observe this warning could

result in severe injury or death.

IMPORTANT SAFETY INFORMATION

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from ying

debris or hydraulic oil.

Wear hearing protection when using

this tool.

Long-term exposure to high noise

levels could result in hearing loss.

Wear foot protection when using this

tool.

Failure to observe this warning could

result in serious injury.

Some types of timber can produce

hazardous dust when cut. Wear a

dust mask to prevent breathing

hazardous dust.

Failure to observe this warning could

result in temporary breathing difculty

or serious injury.

Wear protective gloves when using

this tool.

Failure to observe this warning could

result in serious injury.

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

5

• Do not change accessories, inspect, adjust or

clean the tool or sharpen the chain when it is

connected to a power source. Accidental startup

can result in serious injury.

• Keep the handles clean, dry and free of hydraulic

uid.

• Maintain a rm grip on tool, using both hands with

thumbs and ngers encircling the handles at all

times. Serious injury can result if an operator does

not control the tool.

• Do not lock the trigger in the Power-ON position.

Operator cannot stop tool when trigger is locked.

• Do not remove or modify the tool’s safety trigger.

Accidental startup can result in serious injury.

• Wear protective gloves when handling or adjusting

the chain. The chain can cut even when stationary.

Failure to observe these warnings could result in

severe injury or death.

Saw body, bar, blade and other

components will be hot during and

after use. Use care when handling the

saw. Hot surfaces can cause serious

burns.

Failure to observe this warning could

result in severe injury or death.

To transport the chain saw:

• Allow the chain to stop rotating.

• Wait for the chain to cool.

• Use an appropriate guide bar sheath or scabbard.

• Carry the saw with the guide bar toward the rear.

Failure to observe these warnings could result in

severe injury or death.

IMPORTANT SAFETY INFORMATION

Do not disconnect tool, hoses or ttings while the

power source is running or if the hydraulic uid is hot.

Hot hydraulic uid could cause serious burns.

Do not reverse hydraulic ow. Operation with hydrau-

lic ow reversed could cause tool malfunction.

Connect the pressure hose and tank hose to the

proper ports.

• Use this tool for trimming or pruning trees only.

Any other use can result in injury or property

damage.

• Inspect tool before use. Replace any worn,

damaged or missing parts. A damaged or improp-

erly assembled tool can malfunction, injuring nearby

personnel.

• Inspect hydraulic hoses and couplings every

operating day. Repair or replace if leakage, crack-

ing, wear or damage is evident. Damaged hoses

or couplings can fail resulting in injury or property

damage.

• Ensure that all bystanders and unnecessary

personnel are clear of the work area when operating

the tool. Nearby personnel can be injured by falling

debris.

Failure to observe these precautions may result in

injury or property damage.

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

6

IMPORTANT SAFETY INFORMATION

Hydraulic oil could cause skin irritation.

• Handle the tool and hoses with care to prevent

skin contact with hydraulic oil.

• In case of accidental skin contact with hydraulic

oil, wash the affected area immediately to remove

the oil.

Failure to observe these precautions may result in

injury.

Vibration hazard:

Apply just enough pressure to do the work. Applying

excess pressure to the tool can cause operator dis-

comfort or temporary numbness.

Failure to observe this precaution may result in injury.

• Check the operation of the automatic oiler

frequently. See Checking and Setting the Automatic

Chain Oiler in this manual.

• Check the chain frequently for proper tension and

sharpness. Tension and sharpen as necessary.

See the instructions under Saw Chain and Bar

Maintenance.

• Check the uid level of the power source reservoir

frequently. The automatic oiler uses hydraulic uid

to lubricate the bar and chain, and will cause the

uid level to drop.

Procedure for disconnecting hydraulic hoses, ttings

or components:

1. Move the ow lever on the hydraulic power

source to the OFF position.

2. Stop the power source.

3. Follow the sequence under Disconnecting Hoses

to prevent pressure buildup. In case some pres-

sure has built up, loosen hoses, ttings or com-

ponents slowly.

Emergency stop procedure:

1. Release the trigger.

2. Shut off the hydraulic power source.

Note: Keep decals clean and legible. Replace decals

when necessary.

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

7

Identiﬁcation

1

14

13

12

11

2

3

889 mm (35")

4

5

6

7

8

9

10

Long-Reach Chain Saws

1. Saw Chain 8. Trigger

2. Automatic Oiler 9. Trigger Interlock Latch

3. Hydraulic Gear Motor 10. Trigger Guard or Trigger Strap

4. Serial Number 11. Extension

5. Handle 12. Hand Stop

6. Return Port 13. Saw Head

7. Pressure Port 14. Guide Bar

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

8

Speciﬁcations

Long-Reach Chain Saw

Type of Hydraulic System .............................Open-center

or closed-center

Hydraulic Ports

Pressure ...............................9/16–18 SAE O-ring Boss

Return.....................................3/4–16 SAE O-ring Boss

Cutting Capacity ......................................... 330 mm (13")

Chain Speed @ 30 l/min (8 gpm) ...................1280 m/min

(4200 ft/min)

Sound Power Level .............................................106 Lwa

Vibration ............................................................4.88 m/s

2

Mass/Weight

38568 .................................................. 3.94 kg (8.75 lb)

43177 .................................................. 4.05 kg (9.00 lb)

43178 .................................................. 3.71 kg (8.25 lb)

Length

38568 ................................................. 1890 mm (74.5")

43177 ................................................. 2200 mm (86.5")

43178 ................................................. 1590 mm (62.5")

Width (at motor) ....................................... 108 mm (4.25")

Depth of Body (at handle) ............................ 152 mm (6")

Saw Chain

When replacement is necessary, select a saw chain

that:

• meets applicable industrial safety code

specications

• is rated for 1280 m/min (4200 ft/min)

Failure to observe this warning could result in severe

injury or death.

Pitch ..................................................... 8.26 mm (0.325")

Gauge ................................................... 1.47 mm (0.058")

Hydraulic Power Source

Do not exceed the following hydraulic power source

maximums:

• Hydraulic ow: 30.3 l/min (8 gpm)

• Pressure relief setting: 138 bar (2000 psi)

• Back pressure: 13.8 bar (200 psi)

Failure to observe this warning could result in severe

injury or death.

Type of Hydraulic System .............................Open-center

or closed-center

Flow

Minimum ..........................................18.9 l/min (5 gpm)

Recommended .................................22.7 l/min (6 gpm)

Maximum .........................................30.3 l/min (8 gpm)

Filtration ............................................ 10 micron (nominal)

Pressure Relief Setting ........................138 bar (2000 psi)

Back Pressure (maximum)* ..................13.8 bar (200 psi)

* 13.8 bar (200 psi) is the maximum agreed standard back pressure

for the HTMA (Hydraulic Tool Manufacturers Association).

Greenlee tool will operate satisfactorily at this standard.

1. Maximum hydraulic uid temperature must not

exceed 60 °C (140 °F).

A sufcient oil cooling capac-

ity is needed to limit the hydraulic uid temperature.

2. Hydraulic ow must not exceed 30.3 l/min (8 gpm).

Install a ow meter in the return line to measure the

rate of hydraulic ow before using the tool.

3. Pressure relief valve setting must not exceed

138bar (2000 psi) at your tool’s maximum ow.

Locate the pressure relief valve in the supply circuit

to limit excessive hydraulic pressure to the tool.

Hydraulic Schematic

FILTER

(10 MICRON)

COOLER

RELIEF

VALVE

138 bar

(2000 psi)

CONTROL

VALVE

FLOW METER

T

P

TOOL

RESERVOIR

PUMP

POWER SOURCE

Recommended Hydraulic Fluids

Use any non-detergent, petroleum-based hydraulic

uid which meets the following specications or HTMA

specications.

S.U.S. @:

38 °C (100 °F) ...............................................140 to 225

99 °C (210 °F) ............................................ 40 minimum

Flash Point ................................170 °C (340 °F) minimum

Pour Point ..................................-34 °C (-30 °F) minimum

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

9

Chain Saw Basics

This section introduces some basic principles of chain

saw use: Hazard Prevention, Compression and

Tension.

HAZARD PREVENTION

The cutting action of this chain saw is performed by a

chain-type blade driven at high speed by a powerful

hydraulic motor. When used carefully and properly, the

chain saw is a highly effective cutting tool.

When used improperly, or when anything interferes with

the normal rotation of the blade, the operator could

very suddenly and very quickly lose control of the saw.

Such loss of control can result in harm to the operator.

The three terms that describe loss of control are pull-in,

push-back, and kickback.

Pull-In

Pull-in can occur when the blade at the bottom of the

bar is doing the cutting. If the blade is suddenly pinched

in the cut, or if it contacts a foreign object such as a

nail, the saw may be suddenly and forcefully pulled

away from the operator.

Pull-In

PULL

Push-Back

Push-back can occur when the blade at the top of the

bar is doing the cutting. If the blade is suddenly pinched

in the cut, or if it contacts a foreign object such as a

nail, the saw will be suddenly and forcefully pushed

back toward the operator.

Push-Back

PUSH

Kickback

Kickback is much more hazardous than pull-in or push-

back. When kickback happens, the entire saw may

rotate suddenly and forcefully. The bar of the saw may

quickly travel upward and back, toward the operator.

Kickback can occur when the blade at the guide bar

tip contacts anything while the chain is rotating. Some

causes for kickback are:

• using the guide bar tip for cutting.

• contacting a nail or other metal object when

cutting.

• accidental contact when cutting more than one

branch at a time.

Using Guide Bar Tip for Cutting

Contact with Metal Objects

Metal

Objects

Cutting More Than One Branch at a Time

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

10

Chain Saw Basics (cont’d)

Preventing Pull-In, Push-Back and Kickback

The chain/bar combination and shroud are intended to

prevent or reduce the likelihood and severity of kick-

back. Verify that these items are in good working order

(chain is sharp and properly tensioned, shroud is not

damaged, etc.) to get the maximum benet from these

features. If worn or damaged, replace these items with

Greenlee replacement parts.

General Tips:

• Maintain the saw properly. Verify that the blade is

sharp and has been properly tensioned.

• Do not allow the guide bar tip to contact anything.

• Do not over-reach.

• Do not use the saw above shoulder height.

• Cut only one limb, branch, or log at a time.

• Be aware that small-diameter limbs or branches are

more likely to catch the blade, causing pull-in or

kickback.

Verify that the chain is sharp

and properly tensioned.

Do not allow the

guide bar tip to

contact anything.

Cutting Procedure:

• Hold the chain saw securely with both hands and

maintain a rm, secure grip.

• Bring the chain saw to full rpm before starting the cut.

Maintain full rpm until the cut is completely nished.

• Apply a moderate amount of downward force to the

saw.

• Cut straight through. Do not twist the saw during the

cut.

• Be alert for the limb to shift, which may pinch the saw

in the cut.

• Be alert for a limb or branch under tension to spring

back when the cut is complete and the tension is

released.

Cutting Procedure

Apply a moderate

amount of

downward force.

Bring chain to full rpm.

Maintain full rpm until

the cut is ﬁnished.

Hold saw securely

with both hands.

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

11

Chain Saw Basics (cont’d)

Site Preparation Tips

• Prepare the cutting area by clearing away brush,

branches, vines, etc.

• Remove any unnecessary tools and coil up excess

hydraulic hose.

• Survey the limb or branch to predict the direction or

path of fall. Ensure that no personnel are in that area.

• If working in a municipal area, plan the direction of

fall so that a limb doesn’t fall into a roadway, strike a

nearby building, contact nearby power lines, etc.

• If the tree is on an incline, work uphill from the fall

path. A branch might tend to bounce or roll downhill.

COMPRESSION AND TENSION

Any branch or log will have two forces acting on it

— compression and tension. As the branch or log is cut,

compression tends to push the two halves toward each

other. Tension tends to pull the two halves apart.

See the illustrations. A log or limb supported at both

ends has the compression on the top. A log or limb

supported at one end has the compression on the

bottom.

Make the rst cut on the compression side. Cut through

approximately 1/3 of the log’s diameter. Make the

second cut on the tension side. This will decrease the

likelihood that the saw will become pinched in the cut.

Compression on Top

Side View

1

2

Compression

Tension

Compression on Bottom

Side View

1

2

Compression

Tension

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

12

Setting the Super Spool™

The Super Spool allows the tool to be used with either

open-center or closed-center hydraulic systems.

1. Insert a screwdriver into the spool recess.

2. If using:

• Open-center hydraulic system, turn the

Super Spool counterclockwise until it stops.

• Closed-center hydraulic system, turn the

Super Spool clockwise until it stops.

OC CC

Hoses and Fittings

Installation and Maintenance

See publication 99930323, SAE J1273

(Hose and Hose Assemblies).

Replacement

See a Greenlee catalog or Greenlee publication

99910322, Low Pressure Quick Couplers, Adapters and

Hoses.

Hose Connections

Connecting Hoses

1. Move the ow lever on the hydraulic power source

to the OFF position.

2. Stop the hydraulic power source.

3. Connect the tank hose to the tank (or return) port on

the power source, and then to the tank port on the

tool.

4. Connect the pressure hose to the pressure port or

hose coupler on the tool, and then to the pressure

port on the power source.

Disconnecting Hoses

1. Move the ow lever on the hydraulic power source

to the OFF position.

2. Stop the hydraulic power source.

3. Disconnect the pressure hose from the power

source, and then from the tool.

4. Disconnect the tank hose from the tool, and then

from the power source.

5. Install dust caps over the ports to prevent

contamination.

Typical Setup

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

13

Operation

Electric shock hazard:

• This tool was tested to meet

OSHA 1910.269 (dry test) when

manufactured. It must be properly

cleaned and maintained to ensure

continued non-conductive prop-

erties. When using this unit near

energized electrical lines, use only

certied non-conductive hoses

and proper personal protective

equipment.

• Keep berglass extension clean

and dry when working around

energized electrical lines.

Accumulated oil or dirt reduces the

insulating properties of the tool.

Failure to observe these warnings

could result in severe injury or death.

Skin injection hazard:

Oil under pressure easily punctures

skin causing serious injury, gan-

grene or death. If you are injured by

escaping oil, seek medical attention

immediately.

• Do not use hands to check for

leaks.

• Do not hold hose or couplers while

the hydraulic system is pressurized.

• Depressurize the hydraulic system

before servicing.

Saw body, bar, blade and other

components will be hot during and

after use. Use care when handling the

saw. Hot surfaces can cause serious

burns.

Failure to observe this warning could

result in severe injury or death.

Wear a hard hat when using this tool.

Failure to observe this warning could

result in severe injury or death.

Before operating the saw, read and

understand the following explana-

tions in this manual:

• Pull-In

Pull-in can occur when the blade

at the bottom of the bar contacts

a foreign object, such as a nail,

or when the blade is pinched

in the cut.

The saw will be suddenly and

forcefully pulled away from the

operator.

• Push-back

Push-back can occur when the

blade at the top of the bar con-

tacts a foreign object, such as a

nail, or when the blade is pinched

in the cut.

The saw will be suddenly and

forcefully pushed back toward the

operator.

• Kickback

Kickback can occur when the

chain at the guide bar tip contacts

anything. The bar of the saw will

travel upward and back, toward

the operator.

Failure to observe this warning could

result in severe injury or death.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from ying

debris or hydraulic oil.

Wear hearing protection when using

this tool.

Long-term exposure to high noise

levels could result in hearing loss.

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

14

Wear foot protection when using this

tool.

Failure to observe this warning could

result in serious injury.

Do not disconnect tool, hoses or ttings while the

power source is running or if the hydraulic uid is hot.

Hot hydraulic uid could cause serious burns.

Vibration hazard:

Apply just enough pressure to do the work. Applying

excess pressure to the tool can cause operator dis-

comfort or temporary numbness.

Failure to observe this precaution may result in injury.

• Check the operation of the automatic oiler fre-

quently. See Checking and Setting the Automatic

Chain Oiler in this manual.

• Check the chain frequently for proper tension and

sharpness. Tension and sharpen as necessary.

See the instructions under Saw Chain and Bar

Maintenance.

• Check the uid level of the power source reservoir

frequently. The automatic oiler uses hydraulic uid

to lubricate the bar and chain, and will cause the

uid level to drop.

Emergency stop procedure:

1. Release the trigger.

2. Shut off the hydraulic power source.

Operation (cont’d)

These additional instructions

are derived from

EN 50110-1:

• To avoid electrical danger

and prevent injury or

electrocution:

a) the operator must

have the necessary

technical knowledge

or experience

or

b) the operator must

work under the direct

supervision of another person who has the

necessary technical knowledge or experience.

• This tool must not be used under adverse environ-

mental conditions. These include a lightning storm,

any sign of an approaching lightning storm (such as

thunder), and poor visibility.

• If any electrical lines or other electrical components

carry voltages greater than 50 VAC or 120 VDC,

ensure that:

a) live parts cannot be touched — use screens,

barriers, an enclosure, or insulating covering

or

b) the “live working zone” cannot be reached

with either parts of the body, the tool, or any

accessories.

The live working zone is the distance from any

electrically live part, based on the voltage carried

by the live part. Refer to EN 50110-1, Annex A for

this information.

Note: Maintain proper footing and balance while using

the tool. Do not over-reach. Unsuitable footing and

balance may not allow counteracting normal or unex-

pected movement of the power tool.

1. Grasp the front handle with one hand and the trigger

handle with the other hand.

2. Move the trigger interlock latch forward and pull the

trigger until the saw reaches full rpm.

3.

Feed the rotating saw chain using a steady, constant

pressure.

Note: Cut straight through the wood — do not twist

the saw in the cut.

4. To stop the saw, release the trigger.

5. When the tool is not in use, stop the power source

to reduce heat and wear.

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

15

Maintenance

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from ying

debris or hydraulic oil.

Do not change accessories, inspect, adjust or

clean tool when it is connected to a power source.

Accidental startup can result in serious injury.

Failure to observe this warning could result in severe

injury or death.

SCHEDULE

Use this schedule to maximize the tool’s service life.

Notes:

Keep all decals clean and legible. Replace decals when

necessary.

When disposing of any components (hydraulic hoses,

hydraulic ﬂuid, worn parts, etc.), do so in accordance

with federal, state and local laws or ordinances.

Daily

1. Wipe all tool surfaces clean.

2. Inspect the entire chain before use. Tension and

sharpen the chain as instructed under Saw Chain

and Bar Maintenance. An improperly sharpened,

dull, worn or damaged chain increases the risk of

kickback.

3. Check the operation of the automatic oiler before

use as instructed under Checking and Setting the

Automatic Chain Oiler. An improperly set oiler can

accelerate the wear of the chain and bar.

4. Inspect the hydraulic hoses and ttings for signs

of leaks, cracks, wear or damage. Replace if

necessary.

5. Install dust caps over the hydraulic ports when the

tool is disconnected.

Monthly

1. Perform a thorough inspection of the hydraulic

hoses and ttings as described in publication

99930323, SAE J1273 (Hose and Hose Assemblies).

2. Perform the Bar Service procedure as described

under Saw Chain and Bar Maintenance.

3. Run the saw at full RPM and release the trigger.

Make a note of the time it takes the chain to stop

completely (stop time). Compare to the stop times

recorded during previous months.

An increasing stop time indicates that the trigger

valve components are dirty or worn. Have the tool

cleaned or repaired by an Greenlee Authorized

Service Center.

Annually

If required by your organization, have the tool inspected

by an Greenlee Authorized Service Center.

CHECKING AND SETTING

THE AUTOMATIC CHAIN OILER

The automatic chain oiler provides a constant supply of

oil to lubricate the bar and chain whenever the saw is

operating. An adjustment screw controls the amount of

oil supplied.

Before adjusting the automatic oiler, clean the oil

passage in the base of the guide bar rst. Oil dripping

off the saw head, sprocket cover or bar indicates that

the oil passage is plugged.

1. Run the saw at full rpm.

2. If the tip of the saw gives off a ne spray of oil, the

automatic oiler is working properly. If the saw does

not give off a spray of oil, adjust the oiler.

Note: For better results, hold saw so that the tip of

the saw blade is pointing toward a clean sheet of

paper or cardboard and run the saw at full rpm.

If the automatic oiler is working properly, the paper

or cardboard should soon show small droplets of oil.

3. Stop the hydraulic power source.

4. Fully tighten the oiler screw until it is seated.

Loosen1/4 turn counterclockwise.

Automatic Oiler Adjustment Screw

Automatic Oiler

Adjustment Screw

5. Start the hydraulic power source.

6. Continue to loosen the oiler screw 1/4 turn at a time

until the oiler output is adjusted correctly.

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

16

Maintenance (cont’d)

SAW CHAIN AND BAR MAINTENANCE

New Chain Break-In

1. Run the saw at low chain speed without cutting

wood for 2 to 3 minutes. Check the output from the

automatic oiler.

2. Stop the hydraulic power source. Disconnect the

hoses. Allow the bar and chain to cool. Check the

tension and adjust if necessary.

3. Connect the hoses. Start the power source. Make a

few easy cuts at moderate chain speed.

4. Stop the hydraulic power source. Disconnect the

hoses. Allow the bar and chain to cool. Check the

tension and adjust if necessary.

5. Connect the hoses. Start the power source. Use the

saw for moderate cuts during the next 30 minutes of

use.

Checking Chain Tension

1. Stop the hydraulic power source. Disconnect the

hoses. Allow the bar and chain to cool.

2. Pull the saw chain around the bar. The chain should

rotate around the bar easily. If it does not, see Chain

is Difcult to Rotate Manually in the Troubleshooting

table.

3. Check the tension as follows:

Pull the saw chain away from the bar (see the

illustration) using approximately 4.4 Newtons

(2 lb) of force. The clearance between the chain

and bar should be approximately 3.2 mm (1/8").

If there is too much or too little clearance, proceed

to Adjusting Chain Tension.

Proper Chain Tension

Approx.

4.4 Newtons

(2 lb.)

Approx.

3.2 mm

(1/8")

Adjusting Chain Tension

1. Loosen the two guide bar mounting screws.

2. Turn the saw chain tension adjusting screw until the

proper tension is achieved, as follows:

Pull the saw chain away from the bar (see the

illustration) using approximately 4.4 Newtons (2 lb)

of force. The clearance between the chain and bar

should be approximately 3.2 mm (1/8").

3. Hold the bar nose up and tighten the two bar ange

nuts. Torque to 16.9 Newton-meters (150 in-lb).

4. Check the chain tension again.

5.

Rotate the chain around the bar manually. If you hear

a clicking noise, the chain drive links are hitting the

bar. Repeat the Adjusting Chain Tension procedure.

Bar Service

1. Mark the top side of the bar with a grease pencil or

marker.

2. Remove the chain and bar. Use a small cleaning

brush to remove all residue from the bar groove.

3. Clean the oil passage at the base of the guide bar.

Use any instrument small enough to thoroughly

clean the passage.

4. Check the bar rails for wear by placing a straight

edge against the side of the bar and one cutter.

• Clearance between the bar and straight edge

indicates that the bar rails are not worn.

• If the chain leans and there is little or no clearance

between the bar and straightedge, the bar rails

are worn and the bar should be replaced.

Checking Rails for Wear

CHAIN IS STRAIGHT

Rails are

not worn.

Clearance

STRAIGHTEDGE

Rails are worn.

Replace bar.

CHAIN LEANS

No

Clearance

STRAIGHTEDGE

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

17

Maintenance (cont’d)

5. Inspect the rim sprocket and sprocket adapter.

Replace if worn or damaged.

Rim Sprocket and Sprocket Adapter

Rim Sprocket

Sprocket Adapter

6. Use the mark made in Step 1 to install the bar

upside down, so that the bar will wear evenly.

7. Install the chain as shown. Adjust the tension of the

chain as described under Adjusting Chain Tension.

Direction of Chain Travel

Cutting Edge

Top View

Side View

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

18

Maintenance (cont’d)

SHARPENING THE SAW CHAIN

The saw chain must be sharpened to the manufacturer’s

specications. If the saw chain is not properly sharpened,

the risk of kickback increases.

If using a ling guide or hand-held grinder, refer to the

manufacturer’s instructions provided with the unit.

All Long-Reach Chain Saws are equipped with the

following chain:

See Illustration: Figure A Figure B Figure C Figure D Figure E — Figure F —

Pitch

Gauge

Side

Plate

Angle

Top Plate

Cutting

Angle

Top Plate

Filing

Angle

File

Guide

Angle

Depth

Gauge

Setting

Round

File

Size

.325" .058" 85° 60° 30° 10° .025" 3/16"

Saw Chain Pitch

See Figure A. Pitch refers to the saw chain measure-

ment.

A chain’s pitch is the distance between any three

consecutive rivets divided by two. Example: .65 divided

by two equals .325 pitch.

Figure C

Side Plate Angle

Figure D

Top Plate Cutting Angle

Figure E

Top Plate Filing Angle

Figure F

Depth Gauge Setting

File Guide Angle

Figure A

Pitch

Figure B

Gauge

This distance divided

by two equals Pitch “A”.

Thickness of bottom section

of drive link equals Gauge “B”.

Saw Chain Gauge

See Figure B. Gauge refers to the thickness of that

portion of the drive link which ts into the guide bar

groove. The guide bar and saw chain gauge must

match. Industry standards are .050, .058 and .063.

“C”

“D”

“E”

“F”

10°

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

19

Maintenance (cont’d)

Filing Depth Gauges

1. If the cutters are sharpened with a le holder, check

and lower the depth gauges before sharpening the

cutters.

2. Check the depth gauges every third sharpening.

3. Place the depth gauge tool on the cutter. If the

depth gauge projects, le it level with the top of the

tool. Always le from the inside of the saw chain

toward an outside cutter.

Lowering Depth Gauges

4. Round off the front corner to maintain the original

shape of the depth gauge after using the depth

gauge tool. Always follow the recommended depth

gauge setting of the chain manufacturer. This is

important for maximum performance throughout

the saw chain’s life as well as for protection against

kickback.

Rounding Off Depth Gauges

Filing Cutters — General

1. Support the le holder on the cutter top plate and

depth gauge as shown.

File Holder

File

2. Guide the le at a 10° angle to the cutters.

10°

3. File the cutters on one side of the saw chain from

the inside out. File on the forward stroke only.

4. Keep the line on the le holder parallel to the center

of the saw chain. Reverse the procedure for the

other side.

File Holder Line

5. Keep all cutters the same length.

6. File enough to remove any damage to the cutting

edges (side plate and top plate) of the cutter.

Side Plate Top Plate

Long-Reach Chain Saws

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

20

Troubleshooting

Before troubleshooting, determine whether the problem is in the tool, the hoses, or the power source. Substitute a

tool, hoses, or power source known to be in good working order to eliminate the item that is not operating.

If the problem is in the tool, see the troubleshooting table in this manual. If the problem is in the power source, see

the troubleshooting section of the power source instruction manual.

Problem Probable Cause Probable Remedy

Tool does not operate. Improper power source. Verify that the power source

meets the specications. See the

Specications section.

Hydraulic uid level low. Check the uid level. Check system

for leaks.

Incorrect hydraulic uid viscosity. Use hydraulic uid with the correct

viscosity. See the Specications

section.

Tool operates slowly or erratically. Hydraulic uid cold. Allow uid to warm to the operat-

ing temperature. Actuate the tool

intermittently to reduce the warming

time.

Power source not adjusted correctly. Refer to the power source operator’s

manual. Set the ow and pressure to

correspond with the tool.

Hydraulic uid level low. Check the uid level. Check system

for leaks.

Air in the hydraulic system. See power source manufacturer’s

instructions for removing air from the

system.

Incorrect hydraulic uid viscosity. Use hydraulic uid with the correct

viscosity. See the Specications

section.

Trigger difcult to operate;

trigger sticks when released.

Dirt or gummy deposits on trigger

or spool.

Clean and lubricate trigger and

trigger spool.

Chain runs in wrong direction. Hose connections at tool are

reversed.

Depressurize hydraulic system.

Switch the hose connections.

La page charge ...

Greenlee 38568 - 43177 - 43178 Long Reach Chain Saws Manuel utilisateur

Ce manuel convient également à

Greenlee 38568 - 43177 - 43178 Long Reach Chain Saws Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents