Greenlee LRF 75, 88 Long Reach Chain Saws (foam-filled) Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur
52020553 REV 11 © 2018 Greenlee, Inc. 7/18
Long-Reach Chain Saws
Foam-filled
LRF 75 and 88
INSTRUCTION MANUAL
Español ............................... 23
Français .............................. 45
Deutsch ............................... 67
Italiano ................................ 89
Service .............................. 111
Read and understand all of the instructions and
safety information in this manual before operating
or servicing this tool.
Register this product at www.greenlee.com
Serial Codes AMT, AMS, GLZ, GLY, HAD, and HAE
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
2
Table of Contents
Description ..................................................................... 2
Safety ............................................................................. 2
Purpose .......................................................................... 2
Other Publications .......................................................... 2
Important Safety Information ......................................3-6
Identication ................................................................... 7
Specications ..............................................................8-9
Chain Saw Basics ...................................................10-12
Setting the Super Spool ............................................... 13
Hoses and Fittings ....................................................... 13
Hose Connections ........................................................ 13
Typical Setup ................................................................ 13
Operation .................................................................14-15
Maintenance ............................................................ 16-20
Troubleshooting ....................................................... 21-22
Español ......................................................................... 23
Français ........................................................................ 45
Deutsch ........................................................................ 67
Italiano .......................................................................... 89
Service
Disassembly .......................................................... 111
Assembly ........................................................112-113
Illustrations ..........................................................114-120
Parts List .............................................................121-123
Description
Long-reach chain saws are hydraulically powered cutting
tools intended for general tree trimming from the ground
or from an aerial device.
Greenlee Utility’s patented Super Spool™ design allows
the tool to be used with either open-center or closed-
center hydraulic systems. The dielectric properties of the
berglass pole reduce the chance of electric shock when
the saw is used near energized electrical lines. Other
features include an anti-kickback chain, a fully covered
sprocket guard, a hand-stop safety collar, a trigger inter-
lock and a trigger guard.
Super Spool is protected by U.S. Patent No. 4,548,229.
KEEP THIS MANUAL
Safety
Safety is essential in the use and maintenance of
Greenlee Utility tools and equipment. This instruction
manual and any markings on the tool provide informa-
tion for avoiding hazards and unsafe practices related to
the use of this tool. Observe all of the safety information
provided.
Purpose
This manual is intended to familiarize all personnel
with the safe operation, specications and parts, and
maintenance procedures for the following Greenlee
Utility hydraulic tools:
52020556 LRF 75 Serial Codes
AMT, GLZ, and HAE
52020558 LRF 88 Serial Codes
AMS, GLY, and HAD
Keep this manual available to all personnel.
Replacement manuals are available upon request
at no charge.
Other Publications
Tool Owners/Users
SAE Standard J1273 (Hose and Hose Assemblies):
Publication 99930323
All specications are nominal and may change as design
improvements occur. Greenlee, Inc. shall not be liable for damages
resulting from misapplication or misuse of its products.
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
3
IMPORTANT SAFETY INFORMATION
SAFETY
ALERT
SYMBOL
This symbol is used to call your attention to hazards
or unsafe practices which could result in an injury or
property damage. The signal word, dened below,
indicates the severity of the hazard. The message
after the signal word provides information for
preventing or avoiding the hazard.
Immediate hazards which, if not avoided, WILL result
in severe injury or death.
Hazards which, if not avoided, COULD result in
severe injury or death.
Hazards or unsafe practices which, if not avoided,
MAY result in injury or property damage.
Read and understand all of the
instructions and safety information
in this manual before operating or
servicing this tool.
Failure to observe this warning could
result in severe injury or death.
Electric shock hazard:
This tool was tested to meet
OSHA 1910.269 (dry test) when
manufactured. It must be properly
cleaned and maintained to ensure
continued non-conductive prop-
erties. When using this unit near
energized electrical lines, use only
certied non-conductive hoses
and proper personal protective
equipment.
Keep berglass extension clean
and dry when working around
energized electrical lines.
Accumulated oil or dirt reduces the
insulating properties of the tool.
When using this tool near ener-
gized electrical lines, observe the
instructions provided in DIN EN
50110-1. The signicant sections
of this standard are provided in the
Operation section of this manual.
Failure to observe these warnings
could result in severe injury or death.
Skin injection hazard:
Do not use hands to check for leaks.
Do not hold hose or couplers while
the hydraulic system is pressurized.
Depressurize the hydraulic system
before servicing.
Oil under pressure easily punctures
skin causing serious injury, gangrene
or death. If you are injured by
escaping oil, seek medical attention
immediately.
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
4
IMPORTANT SAFETY INFORMATION
Before operating the saw, read and
understand the following explana-
tions in this manual:
• Pull-In
Pull-in can occur when the blade
at the bottom of the bar contacts
a foreign object, such as a nail, or
when the blade is pinched in the
cut.
The saw will be suddenly and
forcefully pulled away from the
operator.
• Push-back
Push-back can occur when
the blade at the top of the bar
contacts a foreign object, such
as a nail, or when the blade is
pinched in the cut.
The saw will be suddenly and
forcefully pushed back toward the
operator.
• Kickback
Kickback can occur when the
chain at the guide bar tip contacts
anything. The bar of the saw will
travel upward and back, toward
the operator.
Failure to observe this warning could
result in severe injury or death.
Wear a hard hat when using this tool.
Failure to observe this warning could
result in severe injury or death.
Wear eye protection when operating
or servicing this tool.
Failure to wear eye protection could
result in serious eye injury from ying
debris or hydraulic oil.
Wear hearing protection when using
this tool.
Long-term exposure to high noise
levels could result in hearing loss.
Wear foot protection when using this
tool.
Failure to observe this warning could
result in serious injury.
Some types of timber can produce
hazardous dust when cut. Wear
a dust mask to prevent breathing
hazardous dust.
Failure to observe this warning could
result in temporary breathing dif-
culty or serious injury.
Wear protective gloves when using
this tool.
Failure to observe this warning could
result in serious injury.
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
5
IMPORTANT SAFETY INFORMATION
Do not disconnect tool, hoses or ttings while the
power source is running or if the hydraulic uid is
hot. Hot hydraulic uid could cause serious burns.
Do not reverse hydraulic ow. Operation with
hydraulic ow reversed could cause tool malfunc-
tion. Connect the pressure hose and tank hose to the
proper ports.
Use this tool for trimming or pruning trees only.
Any other use may result in injury or property
damage.
Inspect tool before use. Replace any worn,
damaged or missing parts. A damaged or improp-
erly assembled tool can malfunction, injuring
nearby personnel.
Inspect hydraulic hoses and couplings every
operating day. Repair or replace if leakage, crack-
ing, wear or damage is evident. Damaged hoses
or coupling could fail resulting in injury or property
damage.
Ensure that all bystanders and unnecessary
personnel are clear of the work area when operat-
ing the tool. Nearby personnel may be injured by
falling debris.
Failure to observe these precautions may result in
injury or property damage.
Do not change accessories, inspect, adjust or
clean the tool or sharpen the chain when it is
connected to a power source. Accidental startup
could result in serious injury.
Keep the handles clean, dry and free of hydraulic
uid.
Maintain a rm grip on tool, using both hands with
thumbs and ngers encircling the handles at all
times. Serious injury could result if an operator
does not control the tool.
Do not lock the trigger in the Power-ON position.
Operator cannot stop tool when trigger is locked.
Do not remove or modify the tool’s safety trigger.
Accidental startup could result in serious injury.
Wear protective gloves when handling or adjusting
the chain. The chain can cut even when stationary.
Failure to observe these warnings could result in
severe injury or death.
Saw body, bar, blade and other
components will be hot during and
after use. Use care when handling
the saw. Hot surfaces can cause
serious burns.
Failure to observe this warning could
result in severe injury or death.
To transport the chain saw:
Allow the chain to stop rotating.
Wait for the chain to cool.
Use an appropriate guide bar sheath or scabbard.
Carry the saw with the guide bar toward the rear.
Failure to observe these warnings could result in
severe injury or death.
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
6
IMPORTANT SAFETY INFORMATION
Check the operation of the automatic oiler
frequently. See Checking and Setting the
Automatic Chain Oiler in this manual.
Check the chain frequently for proper tension and
sharpness. Tension and sharpen as necessary.
See the instructions under Saw Chain and Bar
Maintenance.
Check the uid level of the power source reservoir
frequently. The automatic oiler uses hydraulic uid
to lubricate the bar and chain, and will cause the
uid level to drop.
Procedure for disconnecting hydraulic hoses, ttings
or components:
1. Move the ow lever on the hydraulic power
source to the OFF position.
2. Stop the power source.
3. Follow the sequence under Disconnecting Hoses
to prevent pressure buildup. In case some
pressure has built up, loosen hoses, ttings or
components slowly.
Emergency stop procedure:
1. Release the trigger.
2. Shut off the hydraulic power source.
Note: Keep decals clean and legible. Replace decals
when necessary.
Hydraulic oil can cause skin irritation.
Handle the tool and hoses with care to prevent
skin contact with hydraulic oil.
In case of accidental skin contact with hydraulic
oil, wash the affected area immediately to remove
the oil.
Failure to observe these precautions may result in
injury.
Vibration hazard:
Apply just enough pressure to do the work. Applying
excess pressure to the tool can cause operator
discomfort or temporary numbness.
Failure to observe this precaution may result in injury.
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
7
Identification
Long-Reach Chain Saws
1. Saw Chain
2. Automatic Oiler
3. Hydraulic Gear Motor
4. Serial Number
5. Handle
6. Return Port
7. Pressure Port
8. Trigger
9. Trigger Interlock Latch
10. Trigger Guard or Trigger Strap
11. Tube Assembly, Foam-lled
12. Hand Stop
13. Saw Head
14. Guide Bar
1
14
13
12
11
2
3
889 mm (35")
4
5
6
7
8
9
10
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
8
Specifications
Long-Reach Chain Saw
Type of Hydraulic System .............................Open-center
or closed-center
Hydraulic Ports
Pressure ...............................9/16–18 SAE O-ring Boss
Return.....................................3/4–16 SAE O-ring Boss
Cutting Capacity ......................................... 330 mm (13")
Chain Speed @ 30 l/min (8 gpm) ................... 1280 m/min
(4200 ft/min)
Sound Power Level ............................................ 106 Lwa
Vibration ............................................................4.88 m/s
2
Mass/Weight
52020556 ............................................ 4.06 kg (9.03 lb)
52020558 ............................................ 4.21 kg (9.36 lb)
Length
52020556 ........................................... 1890 mm (74.5")
52020558 ........................................... 2200 mm (86.5")
Width (at motor) ....................................... 108 mm (4.25")
Depth of Body (at handle) ............................ 152 mm (6")
Saw Chain
When replacement is necessary, select a saw chain that:
meets applicable industrial safety code specications
is rated for 1280 m/min (4200 ft/min)
Failure to observe this warning could result in severe
injury or death.
Pitch ..................................................... 8.26 mm (0.325")
Gauge ................................................... 1.47 mm (0.058")
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
9
Specifications (cont’d)
Hydraulic Power Source
Do not exceed the following hydraulic power source
maximums:
Hydraulic ow: 30.3 l/min (8 gpm)
Pressure relief setting: 138 bar (2000 psi)
Back pressure: 13.8 bar (200 psi)
Failure to observe this warning could result in severe
injury or death.
Type of Hydraulic System .....Open-center or closed-center
Flow
Minimum ..........................................18.9 l/min (5 gpm)
Recommended .................................22.7 l/min (6 gpm)
Maximum .........................................30.3 l/min (8 gpm)
Filtration ............................................ 10 micron (nominal)
Pressure Relief Setting ........................138 bar (2000 psi)
Back Pressure (maximum)* ..................13.8 bar (200 psi)
*
13.8 bar (200 psi) is the maximum agreed standard
back
pressure for the HTMA (Hydraulic Tool Manufacturers
Association). Greenlee Utility tool will operate satisfac-
torily at this standard.
1. Maximum hydraulic uid temperature must not
exceed 60 °C (140 °F). A sufcient oil cooling
capacity is needed to limit the hydraulic uid
temperature.
2. Hydraulic ow must not exceed 30.3 l/min (8 gpm).
Install a ow meter in the return line to measure the
rate of hydraulic ow before using the tool.
3. Pressure relief valve setting must not exceed 138
bar (2000 psi) at your tool’s maximum ow. Locate
the pressure relief valve in the supply circuit to limit
excessive hydraulic pressure to the tool.
Hydraulic Schematic
FILTER
(10 micron)
COOLER
RELIEF
VALVE
138 bar
(2000 psi)
CONTROL
VALVE
FLOW METER
T
P
TOOL
RESERVOIR
PUMP
POWER SOURCE
Recommended Hydraulic Fluids
Use any non-detergent, petroleum-based hydraulic
uid which meets the following specications or HTMA
specications.
S.U.S. @:
38 °C (100 °F) ...............................................140 to 225
99 °C (210 °F) ............................................40 minimum
Flash Point ................................170 °C (340 °F) minimum
Pour Point ..................................-34 °C (-30 °F) minimum
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
10
Kickback
Kickback is much more hazardous than pull-in or push-
back. When kickback happens, the entire saw may
rotate suddenly and forcefully. The bar of the saw may
quickly travel upward and back, toward the operator.
Kickback can occur when the blade at the guide bar
tip contacts anything while the chain is rotating. Some
causes for kickback are:
using the guide bar tip for cutting.
contacting a nail or other metal object when cutting.
accidental contact when cutting more than one
branch at a time.
Using Guide Bar Tip for Cutting
Contact with Metal Objects
Metal
Objects
Cutting More Than One Branch at a Time
Chain Saw Basics
This section introduces some basic principles of chain
saw use: Hazard Prevention, Compression and Tension.
HAZARD PREVENTION
The cutting action of this chain saw is performed by a
chain-type blade driven at high speed by a powerful
hydraulic motor. When used carefully and properly, the
chain saw is a highly effective cutting tool.
When used improperly, or when anything interferes with
the normal rotation of the blade, the operator could
very suddenly and very quickly lose control of the saw.
Such loss of control can result in harm to the operator.
The three terms that describe loss of control are pull-in,
push-back, and kickback.
Pull-In
Pull-in can occur when the blade at the bottom of the
bar is doing the cutting. If the blade is suddenly pinched
in the cut, or if it contacts a foreign object such as a
nail, the saw may be suddenly and forcefully pulled
away from the operator.
Pull-In
PULL
Push-Back
Push-back can occur when the blade at the top of the
bar is doing the cutting. If the blade is suddenly pinched
in the cut, or if it contacts a foreign object such as a
nail, the saw will be suddenly and forcefully pushed
back toward the operator.
Push-Back
PUSH
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
11
Cutting Procedure:
Hold the chain saw securely with both hands and
maintain a rm, secure grip.
Bring the chain saw to full rpm before starting the cut.
Maintain full rpm until the cut is completely nished.
Apply a moderate amount of downward force to the
saw.
Cut straight through. Do not twist the saw during
the cut.
Be alert for the limb to shift, which may pinch the saw
in the cut.
Be alert for a limb or branch under tension to spring
back when the cut is complete and the tension is
released.
Cutting Procedure
Chain Saw Basics (cont’d)
Preventing Pull-In, Push-Back and Kickback
The chain/bar combination and shroud are intended to
prevent or reduce the likelihood and severity of kick-
back. Verify that these items are in good working order
(chain is sharp and properly tensioned, shroud is not
damaged, etc.) to get the maximum benet from these
features. If worn or damaged, replace these items with
Greenlee Utility replacement parts.
General Tips:
Maintain the saw properly. Verify that the blade is
sharp and has been properly tensioned.
Do not allow the guide bar tip to contact anything.
Do not over-reach.
Do not use the saw above shoulder height.
Cut only one limb, branch, or log at a time.
Be aware that small-diameter limbs or branches are
more likely to catch the blade, causing pull-in or
kickback.
Verify that the chain is sharp
and properly tensioned.
Do not allow the
guide bar tip to
contact anything.
Apply a moderate
amount of
downward force.
Bring chain to full rpm.
Maintain full rpm until
the cut is finished.
Hold saw securely
with both hands.
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
12
Chain Saw Basics (cont’d)
Site Preparation Tips
Prepare the cutting area by clearing away brush,
branches, vines, etc.
Remove any unnecessary tools and coil up excess
hydraulic hose.
Survey the limb or branch to predict the direction or
path of fall. Ensure that no personnel are in that area.
If working in a municipal area, plan the direction of
fall so that a limb doesn’t fall into a roadway, strike a
nearby building, contact nearby power lines, etc.
If the tree is on an incline, work uphill from the fall
path. A branch might tend to bounce or roll downhill.
COMPRESSION AND TENSION
Any branch or log will have two forces acting on it—
compression and tension. As the branch or log is cut,
compression tends to push the two halves toward each
other. Tension tends to pull the two halves apart.
See the illustrations. A log or limb supported at both
ends has the compression on the top. A log or limb
supported at one end has the compression on the
bottom.
Make the rst cut on the compression side. Cut through
approximately 1/3 of the log’s diameter. Make the
second cut on the tension side. This will decrease the
likelihood that the saw will become pinched in the cut.
Compression on Top
Side View
1
2
Compression
Tension
Compression on Bottom
Side View
1
2
Compression
Tension
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
13
Setting the Super Spool™
The Super Spool allows the tool to be used with either
open-center or closed-center hydraulic systems.
1. Insert a screwdriver into the spool recess.
2. If using:
Open-center hydraulic system, turn the
Super Spool counterclockwise until it stops.
Closed-center hydraulic system, turn the
Super Spool clockwise until it stops.
OC CC
Hoses and Fittings
Installation and Maintenance
See publication 99930323, SAE J1273
(Hose and Hose Assemblies).
Replacement
See a Greenlee Utility catalog or Greenlee Utility
publication 99910322, Low Pressure Quick Couplers,
Adapters and Hoses.
Hose Connections
Connecting Hoses
1. Move the ow lever on the hydraulic power source
to the OFF position.
2. Stop the hydraulic power source.
3. Connect the tank hose to the tank (or return) port
on the power source, and then to the tank port on
the tool.
4. Connect the pressure hose to the pressure port or
hose coupler on the tool, and then to the pressure
port on the power source.
Disconnecting Hoses
1. Move the ow lever on the hydraulic power source
to the OFF position.
2. Stop the hydraulic power source.
3. Disconnect the pressure hose from the power
source, and then from the tool.
4. Disconnect the tank hose from the tool, and then
from the power source.
5. Install dust caps over the ports to prevent
contamination.
Typical Setup
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
14
Operation
Electric shock hazard:
This tool was tested to meet OSHA
1910.269 (dry test) when manufac-
tured. It must be properly cleaned
and maintained to ensure contin-
ued non-conductive properties.
When using this unit near energized
electrical lines, use only certied
non-conductive hoses and proper
personal protective equipment.
Keep berglass extension clean
and dry when working around
energized electrical lines.
Accumulated oil or dirt reduces the
insulating properties of the tool.
Failure to observe these warnings
could result in severe injury or death.
Skin injection hazard:
Do not use hands to check for leaks.
Do not hold hose or couplers while
the hydraulic system is pressurized.
Depressurize the hydraulic system
before servicing.
Oil under pressure easily punctures
skin causing serious injury, gangrene
or death. If you are injured by escap-
ing oil, seek medical attention
immediately.
Saw body, bar, blade and other
components will be hot during and
after use. Use care when handling the
saw. Hot surfaces can cause serious
burns.
Failure to observe this warning could
result in severe injury or death.
Wear a hard hat when using this tool.
Failure to observe this warning could
result in severe injury or death.
Before operating the saw, read and
understand the following explanations
in this manual:
• Pull-In
Pull-in can occur when the blade
at the bottom of the bar contacts
a foreign object, such as a nail, or
when the blade is pinched in the
cut.
The saw will be suddenly and force-
fully pulled away from the operator.
• Push-back
Push-back can occur when the
blade at the top of the bar contacts
a foreign object, such as a nail, or
when the blade is pinched in the cut.
The saw will be suddenly and
forcefully pushed back toward the
operator.
• Kickback
Kickback can occur when the
chain at the guide bar tip contacts
anything. The bar of the saw will
travel upward and back, toward the
operator.
Failure to observe this warning could
result in severe injury or death.
Wear eye protection when operating
or servicing this tool.
Failure to wear eye protection could
result in serious eye injury from ying
debris or hydraulic oil.
Wear hearing protection when using
this tool.
Long-term exposure to high noise
levels could result in hearing loss.
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
15
Operation (cont’d)
Wear foot protection when using this
tool.
Failure to observe this warning could
result in serious injury.
Do not disconnect tool, hoses or ttings while the
power source is running or if the hydraulic uid is hot.
Hot hydraulic uid could cause serious burns.
Vibration hazard:
Apply just enough pressure to do the work. Applying
excess pressure to the tool can cause operator
discomfort or temporary numbness.
Failure to observe this precaution may result in injury.
Check the operation of the automatic oiler
frequently. See Checking and Setting the Automatic
Chain Oiler in this manual.
Check the chain frequently for proper tension and
sharpness. Tension and sharpen as necessary.
See the instructions under Saw Chain and Bar
Maintenance.
Check the uid level of the power source reservoir
frequently. The automatic oiler uses hydraulic uid
to lubricate the bar and chain, and will cause the
uid level to drop.
Emergency stop procedure:
1. Release the trigger.
2. Shut off the hydraulic power source.
These additional instruc-
tions are derived from EN
50110-1:
To avoid electrical
danger and prevent
injury or electrocution:
a) the operator must
have the necessary
technical knowledge
or experience
or
b) the operator must
work under the
direct supervision of
another person who
has the necessary technical
knowledge or experience.
This tool must not be used under adverse environ-
mental conditions. These include a lightning storm,
any sign of an approaching lightning storm (such as
thunder), and poor visibility.
If any electrical lines or other electrical components
carry voltages greater than 50 VAC or 120 VDC,
ensure that:
a) live parts cannot be touched — use screens,
barriers, an enclosure, or insulating covering
or
b) the “live working zone” cannot be reached
with
either parts of the body, the tool, or any
accessories.
The live working zone is the distance from any
electrically live part, based on the voltage carried
by the live part. Refer to EN 50110-1, Annex A for
this information.
Note: Maintain proper footing and balance while using
the tool. Do not over-reach. Unsuitable footing and
balance may not allow counteracting normal or unex-
pected movement of the power tool.
1. Grasp the front handle with one hand and the trigger
handle with the other hand.
2. Move the trigger interlock latch forward and pull the
trigger until the saw reaches full rpm.
3.
Feed the rotating saw chain using a steady, constant
pressure.
Note: Cut straight through the wood — do not twist
the saw in the cut.
4. To stop the saw, release the trigger.
5. When the tool is not in use, stop the power source
to reduce heat and wear.
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
16
Maintenance
Wear eye protection when operating
or servicing this tool.
Failure to wear eye protection could
result in serious eye injury from ying
debris or hydraulic oil.
Do not change accessories, inspect, adjust or
clean tool when it is connected to a power source.
Accidental startup can result in serious injury.
Failure to observe these warnings could result in
severe injury or death.
SCHEDULE
Use this schedule to maximize the tool’s service life.
Notes:
Keep all decals clean and legible. Replace decals when
necessary.
When disposing of any components (hydraulic hoses,
hydraulic fluid, worn parts, etc.), do so in accordance
with federal, state and local laws or ordinances.
Daily
1. Wipe all tool surfaces clean.
2. Inspect the entire chain before use. Tension and
sharpen the chain as instructed under Saw Chain
and Bar Maintenance. An improperly sharpened,
dull, worn or damaged chain increases the risk of
kickback.
3. Check the operation of the automatic oiler before
use as instructed under Checking and Setting the
Automatic Chain Oiler. An improperly set oiler can
accelerate the wear of the chain and bar.
4. Inspect the hydraulic hoses and ttings for signs
of leaks, cracks, wear or damage. Replace if
necessary.
5. Install dust caps over the hydraulic ports when the
tool is disconnected.
Monthly
1. Perform a thorough inspection of the hydraulic
hoses and ttings as described in publication
99930323, SAE J1273 (Hose and Hose Assemblies).
2. Perform the Bar Service procedure as described
under Saw Chain and Bar Maintenance.
3. Run the saw at full RPM and release the trigger.
Make a note of the time it takes the chain to stop
completely (stop time). Compare to the stop times
recorded during previous months.
An increasing stop time indicates that the trigger
valve components are dirty or worn. Have the
tool cleaned or repaired by an Greenlee Utility
Authorized Service Center.
Annually
If required by your organization, have the tool inspected
by an Greenlee Utility Authorized Service Center.
CHECKING AND SETTING
THE AUTOMATIC CHAIN OILER
The automatic chain oiler provides a constant supply of
oil to lubricate the bar and chain whenever the saw is
operating. An adjustment screw controls the amount of
oil supplied.
Before adjusting the automatic oiler, clean the oil
passage in the base of the guide bar rst. Oil dripping
off the saw head, sprocket cover or bar indicates that
the oil passage is plugged.
1. Run the saw at full rpm.
2. If the tip of the saw gives off a ne spray of oil, the
automatic oiler is working properly. If the saw does
not give off a spray of oil, adjust the oiler.
Note: For better results, hold saw so that the tip of
the saw blade is pointing toward a clean sheet of
paper or cardboard and run the saw at full rpm. If
the automatic oiler is working properly, the paper or
cardboard should soon show small droplets of oil.
3. Stop the hydraulic power source.
4. Fully tighten the oiler screw until it is seated.
Loosen1/4 turn counterclockwise.
Automatic Oiler Adjustment Screw
Automatic Oiler
Adjustment Screw
5. Start the hydraulic power source.
6. Continue to loosen the oiler screw 1/4 turn at a time
until the oiler output is adjusted correctly.
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
17
Maintenance (cont’d)
SAW CHAIN AND BAR MAINTENANCE
New Chain Break-In
1. Run the saw at low chain speed without cutting
wood for 2 to 3 minutes. Check the output from the
automatic oiler.
2. Stop the hydraulic power source. Disconnect the
hoses. Allow the bar and chain to cool. Check the
tension and adjust if necessary.
3. Connect the hoses. Start the power source. Make a
few easy cuts at moderate chain speed.
4. Stop the hydraulic power source. Disconnect the
hoses. Allow the bar and chain to cool. Check the
tension and adjust if necessary.
5. Connect the hoses. Start the power source. Use the
saw for moderate cuts during the next 30 minutes of
use.
Checking Chain Tension
1. Stop the hydraulic power source. Disconnect the
hoses. Allow the bar and chain to cool.
2. Pull the saw chain around the bar. The chain should
rotate around the bar easily. If it does not, see Chain
is Difcult to Rotate Manually in the Troubleshooting
table.
3. Check the tension as follows:
Pull the saw chain away from the bar (see the
illustration) using approximately 4.4 Newtons (2
lb) of force. The clearance between the chain and
bar should be approximately 3.2 mm (1/8"). If there
is too much or too little clearance, proceed to
Adjusting Chain Tension.
Proper Chain Tension
Approx.
4.4 Newtons
(2 lb.)
Approx.
3.2 mm
(1/8")
Adjusting Chain Tension
1. Loosen the two guide bar mounting screws.
2. Turn the saw chain tension adjusting screw until the
proper tension is achieved, as follows:
Pull the saw chain away from the bar (see the
illustration) using approximately 4.4 Newtons (2 lb)
of force. The clearance between the chain and bar
should be approximately 3.2 mm (1/8").
3. Hold the bar nose up and tighten the two bar ange
nuts. Torque to 16.9 Newton-meters (150 in-lb).
4. Check the chain tension again.
5.
Rotate the chain around the bar manually. If you hear
a clicking noise, the chain drive links are hitting the
bar. Repeat the Adjusting Chain Tension procedure.
Bar Service
1. Mark the top side of the bar with a grease pencil or
marker.
2. Remove the chain and bar. Use a small cleaning
brush to remove all residue from the bar groove.
3. Clean the oil passage at the base of the guide bar.
Use any instrument small enough to thoroughly
clean the passage.
4. Check the bar rails for wear by placing a straight
edge against the side of the bar and one cutter.
Clearance between the bar and straight edge
indicates that the bar rails are not worn.
If the chain leans and there is little or no clearance
between the bar and straightedge, the bar rails
are worn and the bar should be replaced.
Checking Rails for Wear
CHAIN IS STRAIGHT
Rails are
not worn.
Clearance
STRAIGHTEDGE
Rails are worn.
Replace bar.
CHAIN LEANS
No
Clearance
STRAIGHTEDGE
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
18
Maintenance (cont’d)
5. Inspect the rim sprocket and sprocket adapter.
Replace if worn or damaged.
Rim Sprocket and Sprocket Adapter
Direction of Chain Travel
Cutting Edge
Top View
Side View
6. Use the mark made in Step 1 to install the bar
upside down, so that the bar will wear evenly.
7. Install the chain as shown. Adjust the tension of the
chain as described under Adjusting Chain Tension.
Rim Sprocket
Sprocket Adapter
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
19
Maintenance (cont’d)
SHARPENING THE SAW CHAIN
The saw chain must be sharpened to the manufacturer’s
specications. If the saw chain is not properly sharp-
ened, the risk of kickback increases.
Saw Chain Pitch
See Figure A. Pitch refers to the saw chain measure-
ment.
A chain’s pitch is the distance between any three
consecutive rivets divided by two. Example: .65 divided
by two equals .325 pitch.
Figure C
Side Plate Angle
Figure D
Top Plate Cutting Angle
Figure E
Top Plate Filing Angle
Figure F
Depth Gauge Setting
File Guide Angle
Figure A
Pitch
Figure B
Gauge
This distance divided
by two equals Pitch “A”.
Thickness of bottom section
of drive link equals Gauge “B”.
Figure A
Pitch
.325"
Figure B
Gauge
.058"
Figure C
Side
Plate
Angle
85°
Figure D
Top Plate
Cutting
Angle
60°
Figure E
Top Plate
Filing
Angle
30°
File
Guide
Angle
10°
Figure F
Depth
Gauge
Setting
.025"
Round
File
Size
3/16"
See Illustration:
If using a ling guide or hand-held grinder, refer to the
manufacturer’s instructions provided with the unit.
All Long-Reach Chain Saws are equipped with the
following chain:
Saw Chain Gauge
See Figure B. Gauge refers to the thickness of that
portion of the drive link which ts into the guide bar
groove. The guide bar and saw chain gauge must
match. Industry standards are .050, .058 and .063.
“C”
“D”
“E”
“F”
10°
Long-Reach Chain Saws (Foam-filled)
Greenlee 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
20
Maintenance (cont’d)
Filing Depth Gauges
1. If the cutters are sharpened with a le holder, check
and lower the depth gauges before sharpening the
cutters.
2. Check the depth gauges every third sharpening.
3. Place the depth gauge tool on the cutter. If the
depth gauge projects, le it level with the top of the
tool. Always le from the inside of the saw chain
toward an outside cutter.
Lowering Depth Gauges
4. Round off the front corner to maintain the original
shape of the depth gauge after using the depth
gauge tool. Always follow the recommended depth
gauge setting of the chain manufacturer. This is
important for maximum performance throughout
the saw chain’s life as well as for protection against
kickback.
Rounding Off Depth Gauges
Filing Cutters — General
1. Support the le holder on the cutter top plate and
depth gauge as shown.
File Holder
File
2. Guide the le at a 10° angle to the cutters.
10°
3. File the cutters on one side of the saw chain from
the inside out. File on the forward stroke only.
4. Keep the line on the le holder parallel to the center
of the saw chain. Reverse the procedure for the
other side.
File Holder Line
5. Keep all cutters the same length.
6. File enough to remove any damage to the cutting
edges (side plate and top plate) of the cutter.
Side Plate Top Plate
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124

Greenlee LRF 75, 88 Long Reach Chain Saws (foam-filled) Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur