Denon AVR-1804 Le manuel du propriétaire

AV SURROUND RECEIVER

RÉCEPTEUR AUDIO-VIDÉO

AVR-1804/884

OPERATING INSTRUCTIONS

MODE D’EMPLOI

2 We greatly appreciate your purchase of the AVR-1804/884.

2 To be sure you take maximum advantage of all the features the AVR-1804/884 has to offer, read these instructions

carefully and use the set properly. Be sure to keep this manual for future reference should any questions or

problems arise.

2 Nous vous remercions de l’achat de l’AVR-1804/884.

2 Pour être sûr de profiter au maximum de toutes les caractéristiques qu’a à offrir l’AVR-1804/884, lire avec soin ces

instructions et bien utiliser l’appareil. Toujours conserver ce mode d’emploi pour s’y référer ultérieurement en cas

de question ou de problème.

FOR ENGLISH READERS PAGE 02 ~ PAGE 065, 128 ~ 132

POUR LES LECTEURS FRANCAIS PAGE 2, 66 ~ PAGE 132

ENGLISH

2

2 SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG

TO WIDE SLOT, FULLY INSERT.

ATTENTION

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU

FOND.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du

Règlement sur le matériel brouilleur du Canada.

“SERIAL NO.

PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE

CABINET FOR FUTURE REFERENCE”

“NO. DE SERIE

PRIERE DE NOTER LE NUMERO DE SERIE DE L’APPAREIL INSCRIT A L’ARRIERE

DU COFFRET DE FAÇON A POUVOIR LE CONSULTER EN CAS DE PROBLEME.”

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

•

FOR CANADA MODEL ONLY

•

POUR LES MODELE CANADIEN UNIQUEMENT

FRANCAIS

2 NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION

• Avoid high temperatures.

Allow for sufficient heat dispersion when

installed on a rack.

• Eviter des températures élevées

Tenir compte d’une dispersion de chaleur

suffisante lors de l’installation sur une étagère.

• Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Manipuler le cordon d’alimentation avec

précaution.

Tenir la prise lors du débranchement du cordon.

• Keep the set free from moisture, water, and

dust.

• Protéger l’appareil contre l’humidité, l’eau et

lapoussière.

• Unplug the power cord when not using the set

for long periods of time.

• Débrancher le cordon d’alimentation lorsque

l’appareil n’est pas utilisé pendant de longues

périodes.

* (For sets with ventilation holes)

• Do not obstruct the ventilation holes.

• Ne pas obstruer les trous d’aération.

• Do not let foreign objects in the set.

• Ne pas laisser des objets étrangers dans

l’appareil.

• Do not let insecticides, benzene, and thinner

come in contact with the set.

• Ne pas mettre en contact des insecticides, du

benzène et un diluant avec l’appareil.

• Never disassemble or modify the set in any

way.

• Ne jamais démonter ou modifier l’appareil

d’une manière ou d’une autre.

3

SAFETY INSTRUCTIONS

1. Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2. Retain Instructions – The safety and operating instructions

should be retained for future reference.

3. Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions should

be followed.

5. Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

6. Attachments – Do not use attachments not recommended by

the product manufacturer as they may cause hazards.

7. Water and Moisture – Do not use this product near water – for

example, near a bath tub, wash bowl, kitchen sink, or laundry

tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall, causing

serious injury to a child or adult, and serious damage to the

product. Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the product.

Any mounting of the product should follow the manufacturer’s

instructions, and should use a

mounting accessory

recommended by the

manufacturer.

9. A product and cart

combination should be

moved with care. Quick

stops, excessive force,

and uneven surfaces may

cause the product and cart

combination to overturn.

10. Ventilation – Slots and openings in the cabinet are provided for

ventilation and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not be

blocked or covered. The openings should never be blocked by

placing the product on a bed, sofa, rug, or other similar surface.

This product should not be placed in a built-in installation such

as a bookcase or rack unless proper ventilation is provided or

the manufacturer’s instructions have been adhered to.

11. Power Sources – This product should be operated only from the

type of power source indicated on the marking label. If you are

not sure of the type of power supply to your home, consult your

product dealer or local power company. For products intended

to operate from battery power, or other sources, refer to the

operating instructions.

12. Grounding or Polarization – This product may be equipped with

a polarized alternating-current line plug (a plug having one blade

wider than the other). This plug will fit into the power outlet

only one way. This is a safety feature. If you are unable to

insert the plug fully into the outlet, try reversing the plug. If the

plug should still fail to fit, contact your electrician to replace your

obsolete outlet. Do not defeat the safety purpose of the

polarized plug.

13. Power-Cord Protection – Power-supply cords should be routed

so that they are not likely to be walked on or pinched by items

placed upon or against them, paying particular attention to

cords at plugs, convenience receptacles, and the point where

they exit from the product.

15. Outdoor Antenna Grounding – If an outside antenna or cable

system is connected to the product, be sure the antenna or

cable system is grounded so as to provide some protection

against voltage surges and built-up static charges. Article 810

of the National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast and

supporting structure, grounding of the lead-in wire to an

antenna discharge unit, size of grounding conductors, location

of antenna-discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode. See Figure A.

16. Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line surges.

17. Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such power lines

or circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such

power lines or circuits as contact with them might be fatal.

18. Overloading – Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result in a risk of

fire or electric shock.

19. Object and Liquid Entry – Never push objects of any kind into

this product through openings as they may touch dangerous

voltage points or short-out parts that could result in a fire or

electric shock. Never spill liquid of any kind on the product.

20.

Servicing – Do not attempt to service this product yourself as

opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

21.

Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service

personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the

product,

c) If the product has been exposed to rain or water,

d) If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation,

e) If the product has been dropped or damaged in any way, and

f) When the product exhibits a distinct change in performance

– this indicates a need for service.

22. Replacement Parts – When replacement parts are required, be

sure the service technician has used replacement parts

specified by the manufacturer or have the same characteristics

as the original part. Unauthorized substitutions may result in

fire, electric shock, or other hazards.

23. Safety Check – Upon completion of any service or repairs to this

product, ask the service technician to perform safety checks to

determine that the product is in proper operating condition.

24. Wall or Ceiling Mounting – The product should be mounted to a

wall or ceiling only as recommended by the manufacturer.

25. Heat – The product should be situated away from heat sources

such as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL

ELECTRICAL CODE

ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

ENGLISH

4

2

INTRODUCTION

2

ACCESSORIES

Thank you for choosing the DENON AVR-1804/884 Digital Surround A/V receiver. This remarkable component has been engineered to provide

superb surround sound listening with AV theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite

music sources.

As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the

contents of this manual before proceeding.

TABLE OF CONTENTS

z Before Using ...............................................................................................5

x Cautions on Installation...............................................................................5

c Cautions on Handling ..................................................................................5

v Features ......................................................................................................6

b Part Names and Functions......................................................................7, 8

n Read this first..............................................................................................9

m Setting up the Speaker Systems ................................................................9

, Connections........................................................................................10~18

. Using the Remote Control Unit ................................................................19

⁄0 Setting up the System........................................................................20~29

⁄1 Remote Control Unit...........................................................................30~34

⁄2 Operation ............................................................................................35~40

⁄3 Multi Zone...........................................................................................41, 42

⁄4 Surround .............................................................................................43~49

⁄5 DSP Surround Simulation ...................................................................50~53

⁄6 Listening to the Radio.........................................................................54~57

⁄7 Last Function Memory..............................................................................57

⁄8 Initialization of the Microprocessor ...........................................................57

⁄9 Additional Information.........................................................................58~63

¤0 Troubleshooting.........................................................................................64

¤1 Specifications ............................................................................................65

List of Preset Codes ..............................................................................128~132

Check that the following parts are included in addition to the main unit:

q Operating instructions .................................................................1

w Warranty......................................................................................1

e Service station list .......................................................................1

r Remote control unit (RC-939)......................................................1

rt y u

t R6P/AA batteries .........................................................................2

y AM loop antenna.........................................................................1

u FM indoor antenna ......................................................................1

ENGLISH

5

2

CAUTIONS ON INSTALLATION

Noise or disturbance of the picture may be generated if this unit or

any other electronic equipment using microprocessors is used near a

tuner or TV.

If this happens, take the following steps:

• Install this unit as far as possible from the tuner or TV.

• Set the antenna wires from the tuner or TV away from this unit’s

power cord and input/output connection cords.

• Noise or disturbance tends to occur particularly when using indoor

antennas or 300 Ω/ohms feeder wires. We recommend using

outdoor antennas and 75 Ω/ohms coaxial cables.

For heat dispersal, leave at least 10 cm of space between the top,

back and sides of this unit and the wall or other components.

4 inch/10 cm or more

Wall

1

BEFORE USING

Pay attention to the following before using this unit:

• Moving the set

To prevent short circuits or damaged wires in the connection cords,

always unplug the power cord and disconnect the connection cords

between all other audio components when moving the set.

• Before turning the power switch on

Check once again that all connections are proper and that there are

not problems with the connection cords. Always set the power

switch to the standby position before connecting and disconnecting

connection cords.

• Store this instructions in a safe place.

After reading, store this instructions along with the warranty in a

safe place.

• Note that the illustrations in this instructions may differ from

the actual set for explanation purposes.

• V. AUX jacks

The AVR-1804/884’s front

panel is equipped with a V.

AUX jacks. Remove the cap

covering the jacks when you

want to use it.

3

CAUTIONS ON HANDLING

• Switching the input function when input jacks are not

connected

A clicking noise may be produced if the input function is switched

when nothing is connected to the input jacks. If this happens, either

turn down the MASTER VOLUME control or connect components

to the input jacks.

• Muting of PRE OUT jacks, HEADPHONE jack and SPEAKER

terminals

The PRE OUT jacks, HEADPHONE jack and SPEAKER terminals

include a muting circuit. Because of this, the output signals are

greatly reduced for several seconds after the power switch is

turned on or input function, surround mode or any other-set-up is

changed. If the volume is turned up during this time, the output will

be very high after the muting circuit stops functioning. Always wait

until the muting circuit turns off before adjusting the volume.

• Whenever the power switch is in the STANDBY state, the

apparatus is still connected on AC line voltage.

Please be sure to unplug the cord when you leave home for,

say, a vacation.

ENGLISH

6

4

FEATURES

1. Dolby Digital EX decoder system

Dolby Digital EX is a 6.1-channel surround format proposed by

Dolby Laboratories that allows users to enjoy in their homes the

“DOLBY DIGITAL SURROUND EX” audio format jointly developed

by Dolby Laboratories and Lucas Films and first used for the movie

“Star Wars Episode 1 – Phantom Menace”.

The 6.1 channels of sound, including surround back channels,

provide improved sound positioning and expression of space.

2. DTS-ES Extended Surround and DTS Neo:6

The AVR-1804/884 is compatible with DTS-ES Extended Surround, a

new multi-channel format developed by Digital Theater Systems Inc.

The AVR-1804/884 is also compatible with DTS Neo:6, a surround

mode allowing 6.1-channel playback of regular stereo sources.

3. Dolby Pro Logic

II decoder

Dolby Pro Logic II is a new format for playing multichannel audio

signals that offers improvements over conventional Dolby Pro

Logic. It can be used to decode not only sources recorded in Dolby

Surround but also regular stereo sources into five channels (front

left/right, center and surround left/right). In addition, various

parameters can be set according to the type of source and the

contents, so you can adjust the sound field with greater precision.

4. Multi Zone Music Entertainment System

Multi Source Function:

This unit’s Multi Source function lets you select different audio

sources for listening Different sources can thus be enjoyed in the

main room (MAIN) and the subroom (ZONE 2) simultaneously.

5. On Screen Diaplay

Troublesome operations such as adjusting the delay time and other

parameters according to the listening environment are greatly

simplified. The various parameters can be set simply by selecting

the graphic displayed on the monitor screen according to the

listening room’s system environment.

6. Video Conversion Function

The AVR-1804/884 is equipped with a function for converting the

signals input to the video input connector and S-Video input

connector. With this function, the AVR-1804/884’s monitor out

connector and the monitor (TV) can be connected with video pin-

plug cords or an S-Video connection cord.

7. Dolby Digital

Using advanced digital processing algorithms, Dolby Digital

provides up to 5.1 channels of wide-range, high fidelity surround

sound. Dolby Digital is the default digital audio delivery system for

North American DVD and DTV.

8. DTS (Digital Theater Systems)

DTS provides up to 5.1 channels of wide-range, high fidelity

surround sound, from sources such as laser disc, DVD and

specially-encoded music discs.

9. Component Video Switching

In addition to composite video and “S” video switching, the AVR-

1804/884 provides 2 sets of component video (Y, P

B/CB, PR/CR)

inputs assignable, and one set of component video outputs to the

television, for superior picture quality.

10.Auto Surround Mode

This function stores the surround mode last used for an input

signal in the memory and automatically sets that surround mode

the next time that signal is input.

7

5

PART NAMES AND FUNCTIONS

Front Panel

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

#4 #3

#2 #0#1

@9 @7@8 @6 @5 @4 @0 !9@2 @1@3

r y i !0 !2 !3 !5 !6 !7 !8q w

te u o !1 !4

q

Power ON/STANDBY switch .......................................(21, 35, 54)

w

Headphones jack (PHONES) ....................................................(39)

e

ZONE2/REC button..........................................................(40 ~ 42)

r

SPEAKER A button.............................................................(35, 57)

t

SPEAKER B button.............................................................(35, 57)

y

SURROUND BACK button .................................................(41, 48)

u

ANALOG button .................................................................(36, 38)

i

EXT. IN button ....................................................................(36, 38)

o

DOLBY/DTS SURROUND button.................................(43, 45, 48)

!0

5CH/6CH STEREO button ........................................................(50)

!1

DIRECT/STEREO button ....................................................(38, 50)

!2

TUNING UP/DOWN buttons ....................................................(55)

!3

V. AUX input jacks................................................................(5, 15)

!4

SURROUND MODE button .........................................(37, 48, 52)

!5

SURROUND PARAMETER button .....................................(45, 51)

!6

SELECT knob ...............................................................(37, 45, 52)

!7

TONE DEFEAT button ..............................................................(39)

!8

TONE CONTROL button ..........................................................(39)

!9

MASTER VOLUME control ......................................................(37)

@0

VIDEO SELECT button .............................................................(39)

@1

STATUS button .........................................................................(40)

@2

DIMMER button.......................................................................(40)

@3

MASTER VOLUME indicator....................................................(37)

@4

Display

@5

PRESET STATION select buttons.......................................(54, 56)

@6

BAND button............................................................................(55)

@7

OUTPUT indicator.....................................................................(41)

@8

SIGNAL indicator......................................................................(37)

@9

INPUT MODE indicator ............................................................(37)

#0

INPUT MODE button ...................................................(36, 38, 48)

#1

Remote control sensor (REMOTE SENSOR) ...........................(19)

#2

Power operation indicator ........................................................(35)

#3

FUNCTION knob ................................................................(36, 40)

#4

MAIN button.............................................................................(36)

ENGLISH

8

Remote control unit

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

SURROUND buttons .............(37, 43, 51)

Cursor buttons.................(20, 32, 44, 51)

Test tone button.................................(43)

Remote control signal

transmitter .........................................(19)

Master volume control

buttons.........................................(36, 42)

POWER buttons ..............(21, 31~33, 35)

MUTING button .................................(39)

Mode selector switches

............................(20, 30~32, 34, 35, 42)

Tuner system/

System buttons ...............(30, 33, 42, 55)

SYSTEM SET UP/

SETUP button ........................(20, 29, 32)

INPUT MODE selector

buttons.........................................(36, 38)

Input source selector buttons

.........................................(31~34, 36, 45)

SURROUND PARAMETER/SYSTEM

button...........................................(32, 45)

CH SELECT (channel select)/ ENTER

button ..............................(20, 32, 44, 46)

SURROUND BACK/RETURN

button ....................................(32, 41, 48)

DIMMER button.................................(40)VIDEO SELECT button.......................(39)

System buttons .....................(30, 32, 33)

LED (indicator) .............................(31, 34)

MULTI ZONE buttons ............(34, 41, 42) MAIN ZONE buttons....................(34, 42)

ON SCREEN/DISPLAY button

.....................................................(32, 40)

ENGLISH

SPEAKER button................................(35)

9

6

READ THIS FIRST

This AV Surround Receiver must be setup before use. Following these steps.

2 Speaker system layout

Basic system layout

• The following is an example of the basic layout for a system consisting of 7 speaker systems and a television monitor:

7

SETTING UP THE SPEAKER SYSTEMS

Step 3 (page 20 to 29)

Finally, setting up the system.

Step 2 (page 19)

Next, insert the batteries into the remote control unit.

Step 1

(page 9 to 18)

Choose the best location to setup the Speakers and connecting the components.

Subwoofer Center speaker system

Surround speaker systems

Surround back speaker system

Front speaker systems

Set these at the sides of the TV or screen with

their front surfaces as flush with the front of the

screen as possible.

ENGLISH

10

R

L

R

L

R

INPUT OUTPUT

LRL

R

OUTPUT

L

R

L

INPUT

OPTICALCOAXIAL

OUTPUT

OPTICAL

L

R

L

R

L

R

L

R

OUTPUT

DIGITAL AUDIODIGITAL AUDIO

B

8

CONNECTIONS

• Do not plug in the AC cord until all connections have been

completed.

• Be sure to connect the left and right channels properly (left with

left, right with right).

• Insert the plugs securely. Incomplete connections will result in the

generation of noise.

• Use the AC OUTLETS for audio equipment only. Do not use

them for hair driers, etc.

• Note that binding pin plug cords together with AC cords or placing

them near a power transformer will result in generating hum or

other noise.

• Noise or humming may be generated if a connected audio

equipment is used independently without turning the power of this

unit on. If this happens, turn on the power of the this unit.

Connecting the audio components

• When making connections, also refer to the operating instructions of the other components.

The power to these outlets is turned on and off when the power is switched between on and standby from the remote control unit or power

switch.

CD player

Connecting a CD player

Connect the CD player’s analog output jacks

(ANALOG OUTPUT) to this unit’s CD jacks using

pin plug cords.

Connecting a turntable

Connect the turntable’s output cord to the AVR-1804/884’s PHONO

jacks, the L (left) plug to the L jack, the R (right) plug to the right jack.

NOTES:

• This unit cannot be used with MC cartridges directly. Use a

separate head amplifier or step-up transformer.

• If humming or other noise is generated when the ground wire

is connected, disconnect the ground wire.

Turntable

(MM cartridge)

Ground wire

Connect the internal amplifier’s subwoofer to the

subwoofer terminal. (Refer to page 17.)

AC OUTLETS

• SWITCHED

(total capacity – 120 W (1 A.))

The power to these outlets is turned on and off in conjunction with the

POWER operation switch on the main unit, and when the power is switched

between on and standby from the remote control unit.

No power is supplied from these outlets when this unit’s power is at standby.

Never connect equipment whose total capacity is above 120 W (1 A.).

NOTE:

Only use the AC OUTLETS for audio equipment. Never use them for hair

driers, TVs or other electrical appliances.

Connecting the AC OUTLETS

AC CORD

AC 120 V, 60 Hz

Connecting a tape deck

Connections for recording:

Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s tape

recording (CDR/TAPE OUT) jacks using pin plug cords.

Connections for playback:

Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s tape

playback (CDR/TAPE IN) jacks using pin plug cords.

CD recorder or Tape deck

Route the connection cords, etc., in such a way

that they do not obstruct the ventilation holes.

MD recorder, CD recorder or other component

equipped with digital input/output jack

CD player or other

component equipped

with digital output jacks

Connecting the DIGITAL jacks

Use these for connections to audio (video) equipment with digital output. Refer to page 26

for instructions on setting this terminal.

NOTES:

• Use 75 Ω/ohms cable pin cords for coaxial connections.

• Use optical cables for optical connections, removing the cap before connecting.

• The main unit’s power must be turned on when recording via the AVR-1804/884.

NOTE:

If humming noise is generated by a

tape deck, etc., move the tape deck

away.

Subwoofer jack

ENGLISH

11

IN

VIDEO

R OUT IN

AUDIO

VIDEO

OUT IN

LRL

R

L

R

L

R OUT IN

AUDIO

VIDEO

OUT IN

LRL

R

L

R

L

R OUT

VIDEO

OUT

L

AUDIO

L

R

R OUT

VIDEO

OUT

L

AUDIO

L

R

L

R

L

R

L

R

L

R

L

RL

B

Connecting video components

• To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can result in a drop in video quality.

• When making connections, also refer to the operating instructions of the other components.

• The AVR-1804/884 is equipped with a function for up-converting video signals.

• The signal connected to the video signal terminal is output to the S-Video monitor out terminals.

• The REC OUT terminals have no conversion function, so when recording only connect the video terminals.

TV or DBS tuner

Connecting a TV/DBS tuner

TV/DBS

• Connect the TV’s or DBS tuner’s video output jack (VIDEO OUTPUT) to the

(yellow) TV/DBS IN jack using a 75 Ω/ohms video coaxial pin plug

cord.

• Connect the TV’s or DBS tuner’s audio output jacks (AUDIO OUTPUT) to

the TV/DBS IN jacks using pin plug cords.

AUDIO

VIDEO

DVD player or video disc player (VDP), etc.

Connecting a DVD player or a video disc player (VDP)

DVD

• Connect the video disc player’s video output jack (VIDEO OUTPUT) to the (yellow)

DVD/VDP IN jack using a 75 Ω/ohms video coaxial pin plug cord.

• Connect the video disc player’s analog audio output jacks (ANALOG AUDIO OUTPUT) to the

DVD/VDP IN jacks using pin plug cords.

• It is also possible to connect a video disc player, DVD player, video game, etc., to the VCR-2

jacks.

AUDIO

VIDEO

Monitor TV

MONITOR OUT

• Connect the TV’s video input jack (VIDEO INPUT) to the

MONITOR OUT jack using a 75 Ω/ohms video

coaxial pin plug cord.

VIDEO

Note on connecting the digital input jacks

• Only audio signals are input to the digital input jacks.

For details, see pages 10, 26.

Video deck 2

Video deck 1

Connecting a video decks

• There are two sets of video deck (VCR) jacks, so two video decks can be connected for simultaneous recording or video copying.

Video input/output connections:

• Connect the video deck’s video output jack (VIDEO OUT) to the (yellow) VCR-1 IN jack, and the video deck’s video input jack (VIDEO IN) to the

(yellow) VCR-1 OUT jack using 75 Ω/ohms video coaxial pin plug cords.

Connecting the audio output jacks

• Connect the video deck’s audio output jacks (AUDIO OUT) to the VCR-1 IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the VCR-1

OUT jacks using pin plug cords.

Connect the second video deck to the VCR-2 jacks in the same way.

AUDIOAUDIO

VIDEOVIDEO

Connecting a Monitor TV

ENGLISH

12

IN

S-VIDEO

OUT

S-VIDEO

OUT

S-VIDEO

IN OUT

S-VIDEO

IN OUT

S-VIDEO

B

Connecting a video component equipped with S-Video jacks

• When making connections, also refer to the operating instructions of the other components.

• A note on the S input jacks

The input selectors for the S inputs and pin jack inputs work in conjunction with each other.

• The AVR-1804/884 is equipped with a function for converting video signals.

• The signal connected to the S-Video signal terminal is output to the composite video monitor out terminals.

• The REC OUT terminals have no conversion function, so when recording only connect the S-Video terminals.

DVD player or video disc player (VDP)

Connecting a DVD player or a video disc player (VDP)

DVD

• Connect the DVD/VDP player’s S-Video output jack to the S-VIDEO

DVD/VDP IN jack using an S-Video connection cord.

• It is also possible to connect a video disc player, DVD/VDP player,

video camcorder, game machine, etc., to the VCR-2 jacks.

Connecting a monitor TV

MONITOR OUT

• Connect the TV’s S video input (S-VIDEO INPUT) to the

MONITOR OUT jack using a S jack connection

cord.

S-VIDEO

Monitor TV

Connecting a TV/DBS tuner

• Connect the TV’s or DBS tuner’s S video output jack (S-VIDEO

OUTPUT) to the TV/DBS IN jack using an S jack

connection cord.

S-VIDEO

TV or satellite broadcast tuner

Video deck 2

Connecting the video decks

• Connect the video deck’s S output jack (S-OUT) to the

VCR-1 IN jack and the video deck’s S input jack (S-IN) to the

VCR-1 OUT jack using S jack connection cords.

• Connect the video deck’s S output jack (S-OUT) to the

VCR-2 IN jack and the video deck’s S input jack (S-IN) to the

VCR-2 OUT jack using S jack connection cords.

S-VIDEO

Video deck 1

Connect the components’ audio inputs and outputs as described on page 11.

ENGLISH

13

VIDEO OUT

Y

CRCB

COMPONENT

B

VIDEO IN

Y

CRCB

COMPONENT

• When making connections, also refer to the operating instructions of the other components.

• The signals input to the color difference (component) video jacks are not output from the VIDEO output jack (yellow) or the S-Video output jack.

In addition, the video signals input to the VIDEO input (yellow) and S-Video input jacks are not output to the color difference (component) video

jacks.

• Some video sources with component video outputs are labeled Y, CB, CR, or Y, Pb, Pr, or Y, R-Y, B-Y. These terms all refer to component video

color difference output.

• At SYSTEM SETUP, the component video input terminal can be assigned for the input sources to which you want to connect AV devices. (For

details, see page 26.)

DVD player

Connecting a DVD player

DVD IN jacks

• Connect the DVD player’s color difference (component) video output jacks

(COMPONENT VIDEO OUTPUT) to the COMPONENT DVD IN jack using 75 Ω/ohms

coaxial video pin-plug cords.

• In the same way, another video source with component video outputs such as a

TV/DBS tuner, etc., can be connected to the TV/DBS color difference (component)

video jacks.

Monitor TV

Connecting a monitor TV

MONITOR OUT jack

• Connect the TV’s color difference (component) video input jacks

(COMPONENT VIDEO INPUT) to the COMPONENT MONITOR OUT jack

using 75 Ω/ohms coaxial video pin-plug cords.

• The color difference input jacks may be indicated differently on

some TVs, monitors or video components (“C

R, CB and Y”, “R-

Y, B-Y and Y”, “Pr, Pb and Y”, etc.). For details, carefully read the

operating instructions included with the TV or other component.

Connecting a Video Component Equipped with Color Difference (Component - Y, PR/CR, PB/CB)

Video Jacks (DVD Player)

• Video Conversion signals

ENGLISH

Signal input to the AVR-1804/884

Video signal output to VIDEO

MONITOR OUT jack (yellow)

Video signal output to S-Video

MONITOR OUT jack

Video signal output to color

difference (component) Video

MONITOR OUT jack

Monitor Output jacks

Video signal input jack

C

(Up-conversion)

E

S-Video signal input jack

C

(Down-conversion)

CE

Color difference (component)

Video signal input jack

EEC

(C : Video signal output, E : Video signal not output)

14

Connecting the antenna terminals

DIRECTION OF

BROADCASTING

STATION

75 Ω/ohms

COAXIAL

CABLE

FM ANTENNA

FM INDOOR

ANTENNA

(Supplied)

AM LOOP

ANTENNA

(Supplied)

AM OUTDOOR

ANTENNA

GROUND

FM ANTENNA

ADAPTER

FEEDER

CABLE

1

4

2

3

AM loop antenna assembly

Connect to the AM

antenna terminals.

Bend in the reverse

direction.

Remove the vinyl tie

and take out the

connection line.

a. With the antenna

on top any stable

surface.

b. With the antenna

attached to a

wall.

Mount

Installation hole Mount on wall, etc.

Connection of AM antennas

1. Push the

lever.

2. Insert the

conductor.

3. Return the

lever.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC which provides guidelines

for proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the

building, as close to the point of cable entry as practical.

Notes:

• Do not connect two FM antennas simultaneously.

• Even if an external AM antenna is used, do not disconnect the

AM loop antenna.

• Make sure AM loop antenna lead terminals do not touch metal

parts of the panel.

ENGLISH

15

L

R

L

R

Connecting the external input (EXT. IN) jacks

• These jacks are for inputting multi-channel audio signals from an outboard decoder, or a component with a different type of multi-channel

decoder, such as a DVD Audio player, or a multi-channel SACD player, or other future multi-channel sound format decoder.

• When making connections, also refer to the operating instructions of the other components.

Decoder with 6-

channel analog output

Front

Surround

Subwoofer

Center

For instructions on playback using the external input (EXT. IN) jacks, see page 38.

Connecting the video component equipped with a V. AUX jacks

To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can result in a drop in sound quality.

R VIDEO OUT S-VIDEO OUTOPTICALL

R VIDEO OUTL

OUTPUT

LINE OUT

DIGITAL OUT

VIDEO OUT

S-VIDEO OUT

VIDEO OUT

LINE OUT

S-VIDEO OUT

L

R

L

R

L

R

Connecting a Video game component

• Connect the Video game component’s output jacks to

this unit’s V. AUX INPUT jacks.

Video game

Video camera

Connecting a video camera component

• Connect the video camera component’s output jacks to

this unit’s V. AUX INPUT jacks.

The V. AUX jacks is covered with a cap. Remove this cap in order to use the terminal. (See page 5 for instructions on removing the cap.)

ENGLISH

16

Connecting the ZONE2 jacks

• If another pre-main (integrated) amplifier is connected, the ZONE2 jacks can be used to play a different program source in ZONE2 at the same

time.

L

R

++

OUTPUT

INPUT

AUX OUT

B

ZONE2

RC-616

INFRARED RETRANSMITTER

Integrated pre-main amplifier

RC-617

INFRARED SENSOR

Extension jacks for future use.

Speaker system connections

• Connect the speaker terminals with the speakers making sure that

like polarities are matched (≈ with ≈ , √ with √). Mismatching of

polarities will result in weak central sound, unclear orientation of

the various instruments, and the sense of direction of the stereo

being impaired.

• When making connections, take care that none of the individual

conductors of the speaker cord come in contact with adjacent

terminals, with other speaker cord conductors, or with the rear

panel.

NOTE:

NEVER touch the speaker terminals when the power is on.

Doing so could result in electric shocks.

Speaker Impedance

• When speaker systems A (

I) and B (II) are use separately, speakers

with an impedance of 6 to 16 Ω/ohms can be connected for use as

front and surround back/ZONE2 speakers.

• Be careful when using two pairs of front and Surround Back/ZONE2

speakers (A + B) and (I + II) at the same time, since use of

speakers with an impedance of 12 to 16 Ω/ohms.

• Speakers with an impedance of 6 to 16 Ω/ohms can be connected

for use as center and surround speakers.

• The protector circuit may be activated if the set is played for long

periods of time at high volumes when speakers with an impedance

lower than the specified impedance are connected.

Connecting the speaker cords

1. Loosen by turning

counterclockwise.

2. Insert the cord. 3. Tighten by turning

clockwise.

Connecting banana plugs

Turn clockwise to tighten, then insert the

banana plug.

Banana plug

1. Push the lever. 2. Insert the cord. 3. Return the lever.

ENGLISH

17

(

I

) (

II

)

(

L

) (

R

) (

L

) (

R

)

(

L

) (

R

)

Connections

• When making connections, also refer to the operating instructions of the other components.

Connection jack for subwoofer with

built-in amplifier (super woofer), etc.

CENTER SPEAKER

SYSTEM

SURROUND BACK/MULTI ZONE SPEAKER SYSTEMS

SURROUND SPEAKER

SYSTEMS

• Precautions when connecting speakers

If a speaker is placed near a TV or video monitor, the colors on the screen may be disturbed by the speaker’s magnetism. If this should

happen, move the speaker away to a position where it does not have this effect.

NOTES:

• To use Surround back with one speaker,

connect the speaker to SURR. BACK (I).

• The settings must be changed to use this

speaker for ZONE2. (See page 28)

• The same signal is output simultaneously

to the SURR.BACK/ZONE2 I and II

terminals.

FRONT SPEAKER

(B) SYSTEMS

FRONT SPEAKER

(A) SYSTEMS

ENGLISH

18

• This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under

circumstances such as when the output of the power amplifier is inadvertently short-circuited and a large current flows, when

the temperature surrounding the unit becomes unusually high, or when the unit is used at high output over a long period

which results in an extreme temperature rise.

When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED flashes. Should

this occur, please follow these steps: be sure to switch off the power of this unit, check whether there are any faults with

the wiring of the speaker cables or input cables, and wait for the unit to cool down if it is very hot. Improve the ventilation

condition around the unit and switch the power back on.

If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the

unit, switch off the power and contact a DENON service center.

Protector circuit

• The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with an

impedance lower than the specified impedance (for example speakers with an impedance of lower than 4 Ω/ohms) are

connected. If the protector circuit is activated, the speaker output is cut off. Turn off the set’s power, wait for the set to cool

down, improve the ventilation around the set, then turn the power back on.

Note on speaker impedance

ENGLISH

19

9

USING THE REMOTE CONTROL UNIT

Following the procedure outlined below, insert the batteries before using the remote control unit.

Range of operation of the remote control unit

Inserting the batteries

Point the remote control unit at the remote control sensor as shown

on the diagram at the left.

NOTES:

• The remote control unit can be used from a straight distance of

approximately 23 feet/7 meters, but this distance will shorten or

operation will become difficult if there are obstacles between the

remote control unit and the remote control sensor, if the remote

control sensor is exposed to direct sunlight or other strong light, or

if operated from an angle.

• Neon signs or other devices emitting pulse-type noise nearby may

result in malfunction, so keep the set as far away from such

devices as possible.

Approx. 23 feet/7 m

30°

w Insert the R6P/AA batteries properly, as

shown on the diagram.

q Press as shown by the arrow and slide

off.

e Close the lid.

NOTES:

• Use only R6P/AA batteries for replacement.

• Be sure the polarities are correct. (See the illustration inside the battery compartment.)

• Remove the batteries if the remote control transmitter will not be used for an extended period of time.

• If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the

battery compartment thoroughly before installing new batteries.

• Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the time comes.

• Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is

operated nearby the set. (The included battery is only for verifying operation. Replace it with a new battery as soon as possible.)

ENGLISH

20

10

SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 10 to 18), make the

various settings described below on the display.

These settings are required to set up the listening room’s AV system centered around the this unit.

• Use the following buttons to set up the system:

SYSTEM SETUP button

Press this to display the system setup on the display.

CURSOR buttons (•, ª, 0, 1)

Press this change what appears on the display.

ENTER button

Press this to switch the display.

Also use this button to complete the setting.

1

Set the slide switch to “AUDIO”.

2

Use the following buttons to set up the system:

• System setup items and default values (set upon shipment from the factory)

System setup Default settings

Speaker

Configuration

Subwoofer mode

Digital In

Assignment

Auto Surround

Mode

Input the combination of speakers in your system and their

corresponding sizes (SMALL for regular speakers, LARGE for full-

size, full-range) to automatically set the composition of the signals

output from the speakers and the frequency response.

This selects the subwoofer speaker for playing deep bass signals.

This assigns the digital input jacks for the different

input sources.

Auto surround mode function setting.

Input source

Digital

Inputs

Front Sp.

Large

Center Sp. SubwooferSurround Sp.

Small YesSmall

LFE (Normal)

Front L Center Surround Back

12 ft 12 ft 10 ft

CD DVD/VDP TV/DBS

VCR-1

VCR-2 CDR/TAPE

COAXIAL OPTICAL 1 OPTICAL 2 OFF OFF OPTICAL 3

Auto Surround Mode = ON

Surround Back Sp.

Small

Delay Time

This parameter is for optimizing the timing with which the audio

signals are produced from the speakers and subwoofer according

to the listening position.

Subwoofer

12 ft

Crossover

Frequency

Set the frequency (Hz) below which the bass sound of the various

speakers is to be output from the subwoofer.

80 Hz

Video In

Assignment

This assigns the component video input jacks for

the different video input sources.

Input source

Component

Inputs

DVD/VDP TV/DBS

VCR-1

VCR-2 V. AUX —

VIDEO 1 VIDEO 2 OFF OFF OFF —

Ext. In SW Level Set the Ext. In Subwoofer channel playback level. Ext. In SW Level = +15 dB

Power AMP

Assignment

Set this to switch the surround back channel’s power amplifier for

use for Zone 2.

Surround Back

On Screen

Display

This sets whether or not to display the on-screen display that

appears on the monitor screen when the controls on the remote

control unit or main unit are operated.

ON

Auto Tuner

Presets

FM stations are received automatically and stored in the memory.

A1 ~ A8

B1 ~ B8

C1 ~ C8

D1 ~ D8

E1 ~ E8

87.5/89.1/98.1/107.9/90.1/90.1/90.1/90.1 MHz

520/600/1000/1400/1500/1710 kHz, 90.1/90.1 MHz

90.1 MHz

ENGLISH

Front L Front R Center

0 dB 0 dB 0 dB

Test Tone

This adjusts the volume of the signals output from the speakers

and subwoofer for the different channels in order to obtain

optimum effects.

Surround L

0 dB

Surround R

0 dB

Surround Back

0 dB

Subwoofer

0 dB

Front R

12 ft

Surround L

10 ft

Surround R

10 ft

La page charge ...

Denon AVR-1804 Le manuel du propriétaire

Ce manuel convient également à

Denon AVR-1804 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents