Sherwood R-507 Operating Instructions Manual

R-607/R-507

AUDIO/VIDEO RECEIVER

RÉCEPTEUR AUDIO/VIDÉO

RECEPTOR DE AUDIO/VÍDEO

AUDIO/VIDEO RECEIVER

АУДИО-/ВИДЕОРЕСИВЕР

OPERATING INSTRUCTIONS

GUIDE D’UTILISATION

INSTRUCCIONES DE FUNCIONAMIENTO

BEDIENUNGSANLEITUNG

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

2

Safety Information

READ THIS BEFORE OPERATING YOUR UNIT

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE FRONT OR BACK COVER. NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates the presence of uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufcient magnitude to constitute a risk of electric shock.

This symbol indicates important operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

Caution regarding installation

Note

Wall

Do not block ventilation openings or stack other equipment on the top.

Note:

For heat dispersal, do not install this unit in a conned space such as a bookcase or similar enclosure.

CAUTION

•

Leave space around the unit for sufcient ventilation.

•

Avoid installation in extremely hot or cold locations, or in an

area that is exposed to direct sunlight or heating equipment.

•

Keep the unit free from moisture, water, and dust.

•

Do not let foreign objects in the unit.

•

Keep the ventilation openings clear of items, such as

newspapers, linens, or curtains.

•

Keep open ame from candles or other sources away from the

unit.

•

Observe the local regulations regarding disposal of packaging

materials, exhausted batteries and old equipment.

•

Do not expose the unit to dripping or splashing, or place objects

lled with liquids such as vases.

•

Do not let insecticides, benzene, or thinner come in contact

with the unit.

•

Never disassemble or modify the unit in any way.

Notes on the AC power cord and the wall outlet

•

The unit remains connected to AC power as long as it is

plugged into the wall outlet, even if the unit has been turned off.

•

To completely disconnect this product from AC power,

disconnect the plug from the wall socket outlet.

•

When setting up this product, make sure that the AC outlet you

are using is easily accessible.

•

Disconnect the plug from the wall outlet when not using the unit

for long periods of time.

Manufactured under license under U.S.

Patent Nos: 5,956,674; 5,974,380;

6,226,616; 6,487,535; 7,212,872;

7,333,929; 7,392,195; 7,272,567 &

other U.S. and worldwide patents issued & pending. DTS-HD,

the Symbol, & DTS-HD and the Symbol together are registered

trademarks & DTS-HD Master Audio is a trademark of DTS, Inc.

Manufactured under license from

Dolby Laboratories. Dolby, Pro

Logic, and the double-D symbol are

trademarks of Dolby Laboratories.

HDMI, the HDMI Logo, and High-

Denition Multimedia Interface are

trademarks or registered trademarks

of HDMI Licensing LLC in the United States and other contries.

* DTS-HD Master Audio and Dolby TrueHD is applicable only for

R-607.

3

English

Table of Contents

2 SAFETY INFORMATION

4 GETTING STARTED

4 Front Panel

4 Rear Panel

5 Remote Control

6 Placement

7 CONNECTIONS

7 Connect Your Speakers

7 Connect Your Subwoofer

8 Connect Your TV or Video Display

9 Connect Your Audio and Video Source Devices

13 Connect the Tuner Antennas

13 Connect to AC Power

13 Install the Batteries in the Remote Control

14 SETUP

14 Turn On the AVR

14 Congure the AVR for Your Speakers

16 OPERATION

16 Operating Your AVR

16 Listening to FM and AM Radio

17 Listening to Media on a USB Device

17 Selecting a Surround Mode

18 Advanced Functions

20 TROUBLESHOOTING

21 SPECIFICATIONS

4

Getting Started

Front Panel

8 9 10 11 14 15

1 2 3 4 5 6 7

12 13

1

Main Power Switch

2

Standby Indicator

3

On/Standby Switch

4

IR Sensor

5

Display

6

Surround Select Buttons

7

Master Volume Control

8

Input Selector

9

Headphone Connector

10

F.AUX Input Connector

11

Band Select Button

12

Tuning Up/Down Buttons

13

Preset Select Buttons

14

Stereo Mode Button

15

USB Port

Rear Panel

3 4 5 6 7 8

1 2

1

Digital Audio Connectors

2

HDMI Connectors

3

Tuner Antenna Connectors

4

Analog Audio Connectors

5

Subwoofer Connector

6

Composite Video Connectors

7

Speaker Connectors

8

AC Input Connector

Getting Started

5

English

Remote Control

1

Power On Button

2

Source Select Buttons

3

Surround Select Buttons

(The GAME and NETWORK buttons are

not available.)

4

Top Menu Button

5

▲/▼/◄/► Select Buttons

ENTER/MEMO Enter/Memory Button

SEARCH.M RDS Search Button

(* The SEARCH.M button is available only

in models that are distributed in Europe.)

6

Display/Mode Button

7

Stop Button

8

Repeat Button

9

Tuning Up/Down Buttons

Rewind/Fast forward Buttons

10

Preset Station Up/Down Buttons

Previous/Next Buttons

11

Random Button

12

Play/Pause Button

13

Return Button

14

Volume Up/Down Buttons

15

Setup Menu Button

16

Mute Button

17

Stereo Mode Button

18

Audio Assign Button

19

Channel Level Button

20

Test Tone Sequence Button

21

Tone Control Button

22

Standby Button

1

4

6

5

8

9

7

2

3

17

15

22

16

11

21

20

19

18

14

10

13

12

R-607/R-507AUDIO/VIDEORECEIVER

6

Placement

Place Your Speakers

Determine the locations for your system’s speakers

according to their manufacturer’s directions and the

layout of your listening room. Use the illustration below

as a guide for 5.1-channel systems.

To create the most realistic surround-sound environment

possible, you should place your speakers in a circle

with the listening position at its center. You should angle

each speaker so it directly faces the listening position.

Use the diagram below as a guide.

Placing the Left, Center and Right

Speakers

Place the center speaker either on top of, below or

mounted on the wall above or below the TV or video-

display screen. Place the front left and right speakers

along the circle, about 30 degrees from the center

speaker and angled toward the listener.

Place the front left, front right and center speakers at

the same height, preferably at about the same height

as the listener’s ears. The center speaker should be

no more than 2 feet (0.6m) above or below the left/

right speakers. If you’re using only two speakers with

your AVR, place them in the front left and front right

positions.

Placing the Surround Speakers

You should place the left and right surround speakers

approximately 110 degrees from the center speaker,

slightly behind and angled toward the listener.

Alternatively, you can place them behind the listener,

with each surround speaker facing the opposite-side

front speaker. You should place the surround speakers

2 feet – 6 feet (0.6m – 1.8m) higher than the listener’s

ears.

Placing the Subwoofer

Because a room’s shape and volume can have a

dramatic effect on a subwoofer’s performance, it is best

to experiment with placement so that you will nd the

location that produces the best results in your particular

listening room. With that in mind, these rules will help

you get started:

•

Placing the subwoofer next to a wall generally will

increase the amount of bass in the room.

•

Placing the subwoofer in a corner generally will

maximize the amount of bass in the room.

•

In many rooms, placing the subwoofer along the

same plane as the left and right speakers can

produce the best integration between the sound of

the subwoofer and that of the left and right speakers.

•

In some rooms, the best performance could even

result from placing the subwoofer behind the

listening position. A good way to determine the best

location for the subwoofer is by temporarily placing it

in the listening position and playing music with strong

bass content. Move around to various locations in

the room while the system is playing (putting your

ears where the subwoofer would be placed), and

listen until you nd the location where the bass

performance is best. Place the subwoofer in that

location.

7

English

Connections

•

Before making any connections to the audio/

video receiver, ensure that the AVR’s AC cord

is unplugged from the AVR and the AC outlet.

Making connections with the AVR plugged in and

turned on could damage the speakers.

Caution

Connect Your Speakers

HowtousetheAVR’sspeakerterminals

1

Unscrew Cap

2

Insert Bare Wire

3

Tighten Cap

Always connect the colored (+) terminal on the AVR to

the (+) terminal on the speaker (usually red), and the

black (–) terminal on the AVR to the (–) terminal on the

speaker (usually black).

•

Make sure the (+) and (–) bare wires do not touch

each other or the other terminal. Touching wires

can cause a short circuit that can damage your

AVR.

Caution

Connect the speakers as shown in the illustration.

Connect Your Subwoofer

Use a single RCA audio cable to connect the AVR’s

Subwoofer Pre-Out connector to your subwoofer.

Consult your subwoofer’s user manual for specic

information about making connections to it.

Subwoofer

Rear Panel

8

R-607/R-507AUDIO/VIDEORECEIVER

Connect Your TV or Video

Display

HDMI Monitor Out Connector

If your TV has an HDMI connector and you have HDMI

video source devices, use an HDMI cable (not supplied)

to connect your TV to the AVR’s HDMI Monitor Out

connector.

It will provide the best possible picture quality.

Rear Panel

CompositeVideoMonitorOutConnector

If your TV does not have an HDMI connector, or if

your TV does have an HDMI connector

but you are

connecting some source devices with only composite

video connectors

, use a composite video cable (not

included) to connect the AVR's Composite Monitor Out

connector to your TV’s composite video connector.

Composite

VIDEO IN

Rear Panel

Composite Video Cable

(not supplied)

TV

•

The AVR’s on-screen display (OSD) only appears

through the Composite Monitor Out connector. If

you want to use the AVR’s OSD menus you need

to connect its Composite Monitor Out connector

to your TV even if you are not connecting any

composite video source devices to the AVR.

Note

9

Connections

English

Connect Your Audio and

Video Source Devices

Source devices are components where a playback

signal originates, e.g., a Blu-ray Disc™ or DVD player;

a cable, satellite or HDTV tuner; etc. Your AVR has

several different types of input connectors for your

audio and video source devices: HDMI, composite

video, optical digital audio, coaxial digital audio and

analog audio.

Each of your AVR’s source buttons is assigned to an

analog audio input connector.

The digital inputs are not assigned to any specic sets

of analog inputs. Once you select a source device you

can use the remote control’s DIGITAL button to select

the specic audio input connection (HDMI, coaxial

digital, optical digital, analog) that you want to listen to.

(Note: You cannot select an audio input connection for

the FM/AM or USB source buttons.)

As you connect your various source components, ll out

the “Source Device Connected” and “Digital Audio Input

Connector Used” columns in the following table. it will

make it easy to keep track of which devices you have

connected to which connectors.

HDMI Devices

If any of your source devices have HDMI connectors,

using those connectors will provide the best possible

video and audio performance quality. Since the HDMI

cable carries both digital video and digital audio

signals, you do not have to make any additional audio

connections for devices you connect via HDMI cables.

If you have a TV equipped with the HDMI Audio Return

Channel function, its sound is fed to the AVR via the

HDMI Monitor Out connection’s Audio Return Channel,

and it will not require additional audio connections to

the AVR.

HDMI Cable

(not supplied)

HDMI-Equipped Source Device

Rear Panel

10

R-607/R-507AUDIO/VIDEORECEIVER

CompositeVideoDevices

You will need to make composite video connections

from your source devices that do not have HDMI video

connections. You will also need to make an audio

connection from the device to the AVR.

Composite

VIDEO OUT

Rear Panel

Composite Video Cable

(not supplied)

Composite Video-Equipped

Source Device

Optical Digital Audio Devices

If your source devices have optical digital outputs,

connect them to the AVR’s optical digital audio

connectors.

OPTICAL

OUT

Rear Panel

TV, DVD Player, etc.

11

Connections

English

Coaxial Digital Audio Devices

If your source devices have coaxial digital outputs,

connect them to the AVR’s coaxial digital audio

connectors.

OUT

Rear Panel

TV, DVD Player, etc.

OUT

Analog Audio Devices

Make analog audio connections from your source

devices that do not have HDMI or digital audio

connections. If you’re connecting video sources to the

AVR’s Video 1 or Video 2 audio inputs, you must also

connect the source device’s composite video output to

the corresponding composite video connector.

RL

TV, DVD Player, etc.

Rear Panel

12

R-607/R-507AUDIO/VIDEORECEIVER

Audio Recorder

Connect an analog audio recorder’s inputs to the AVR’s

analog audio Tape Out connectors.

You can record any analog audio input signal (except

Tape In).

RL

Rear Panel

Analog Audio Recording Device

VideoRecorders

Connect an analog video recorder’s video input

connector to the AVR’s Video 1 Out composite video

connector and its audio input connectors to the AVR’s

Video 1 Out analog audio connectors. You can record

the Video 2 composite video input signal.

Rear Panel

R L

AUDIO IN (COMPOSITE)

VIDEO

Analog Video Recording Device

IN

13

Connections

English

Connect the Tuner Antennas

•

Connect the supplied FM antenna to the AVR’s FM

75Ω antenna connector. For the best reception,

extend the FM antenna as far as possible.

•

Bend and fold the base of the supplied AM antenna

as shown and connect the antenna wires to the

AVR’s AM and Gnd connectors. Rotate the antenna

as necessary to minimize background noise.

Rear Panel

AM Loop Antenna

Connect to AC Power

Connect the AC power cord to the AVR’s AC Input

connector and then to a working AC power outlet.

AC power cord

To the wall outlet

Rear Panel

•

Before connecting the AC power cord, make

sure that the AC voltage listed on the AVR’s

back panel matches the AC voltage used in your

country.

Note

Install the Batteries in the

Remote Control

Remove the remote control’s battery cover, insert the

two supplied AAA batteries as shown in the illustration,

and replace the battery cover.

•

Remove the protective plastic from the AVR’s

front panel to keep it from reducing the remote

control’s effectiveness.

Note

14

Setup

Turn On the AVR

1

Set the AVR’s Main Power switch to “On”.

(The Standby indicator will glow red.)

2

Press the front-panel On/Standby button.

Main Power Switch Standby Indicator

On/Standby Button

On the remote control, you can only turn on or off the

AVR to standby mode by following the steps below.

When the power button is pressed on the main unit,

you cannot turn on the main unit even by pressing the

power button on the remote control.

Standby

Button

POWER

ON

Button

1

Press POWER ON on the standby mode.

2

Press STANDBY to turn on the standby mode.

Congure the AVR for Your

Speakers

You will be using the following remote control buttons to

congure your AVR:

Setup

Menu

Button

Enter

Button

Return

Button

Left/

Right/

Up/

Down

Buttons

1

Turn on your TV and select the TV input where

you connected the AVR’s Composite Monitor

Out connector in

Connect Your Audio and Video

Source Devices

, on page 9.

•

Although you can congure the AVR using only

its front-panel message display, it is much easier

to use the On-Screen Display (OSD) menu

system.

Note

2

Press the remote control’s SETUP button. The

AVR’s OSD System Setup menu will appear on

the TV.

System Setup

1. Speaker Setup

2. HDMI Setup

3. Audio Setting’s

4. Auto Power Control

5. Speakers On/Off

3

Use the remote’s arrow and ENTER buttons

to select “Speaker Setup”. The Speaker Setup

menu will appear.

a. Speaker Setting’s

1. Speaker Setup

b. Crossover

c. Channel Level

d. Speaker Distance

15

Setup

English

4

Select “Speaker Settings”. The Speaker Settings

menu will appear.

SpeaKer Setting’s1a.

Front

Center

Surrround L/R

Subwoofer

< LARGE >

[ LARGE ]

[ YES ]

5

Use the remote’s left and right arrow buttons

to select NO, SMALL or LARGE for the Front,

Center and Surround speaker positions,

depending on the speakers you have connected

to the receiver.

NO:

Select this setting if you have not connected

a speaker in that position (not available for the

Front speakers).

SMALL:

Select this setting if the speaker is not

capable of producing clean, deep bass energy

at output levels that match those produced by

a powered subwoofer. All bass in that channel

is removed from that speaker and is sent to the

subwoofer (or to the Front speakers if Subwoofer

is set to NO). Most speakers (unless they are

large and powerful) should be considered

SMALL.

LARGE:

Select this setting if the speaker is

capable of producing clean, deep bass energy

at output levels that match those produced by a

powered subwoofer. All bass in that channel is

sent to that speaker.

When you’re nished, press the remote control’s

RETURN button to return to the Speaker Setting

menu.

•

If your system has a subwoofer and you set the

Front speakers to LARGE, the subwoofer may

not output audio except for Dolby Digital and

DTS encoded program material that contains

LFE channel information. If you set your

Front speakers to LARGE and you want your

subwoofer to reproduce bass from all program

material, set the Subwoofer to PLUS (see below).

•

For Subwoofer, select YES (if your system has

a subwoofer), NO (if your system does not

have a subwoofer), or PLUS (if your system

has a subwoofer, you set your Front speakers

to LARGE and you want your subwoofer to

reproduce bass from all program material).

Note

6

For now you can skip the “Crossover” setting.

7

Select “Speaker Distance”. The Speaker

Distance menu will appear.

SpeaKer Distance1d.

Units [ FEET ]

Front L

Center

Front R

Surrround R

Surrround L

Subwoofer

< 10.0ft >

[ 10.0ft ]

•

The unit display may differ depending on the

distributed models.

Note

8

Measure the distance from each speaker in your

system to the listening position. Write down the

distances.

9

Use the remote’s left and right arrow buttons to

change the distance setting for each speaker so

it matches the distance you wrote down in step 8.

When you’re nished, press the remote control’s

RETURN button to return to the Speaker Setting

menu.

10

Select “Channel Level”. The Channel Level

menu will appear. Use the remote’s left and

right arrow buttons to set Test Tone to “Manual”

and press the remote’s ENTER button. After the

on-screen countdown you will hear test noise

through the front left speaker.

Channel Level1c.

Test Tone < Manual >

11

Sit in the main listening position and adjust

the AVR’s volume control so the test noise

is moderately loud. Note the volume of the

test noise through the rst speaker. Press the

remote’s down arrow button to advance the

test noise to each of your system’s speakers

and note the volume level of the noise in each

speaker.

12

As you advance the test noise through the

speakers, use the remote’s left and right arrow

buttons to adjust the volumes of the channels

until all of them play at the same volume.

When you’re nished, press the remote’s SETUP

button to turn of the on-screen menus.

16

Operation

Operating Your AVR

Now that you have installed your components and

completed a basic conguration, you are ready to begin

enjoying your home theater system.

ControllingtheVolume

Adjust the volume either by turning the front-panel

Volume knob (clockwise to increase volume or

counterclockwise to decrease volume) or by pressing

the Volume Up/Down buttons on the remote.

Muting the Sound

To mute all speakers and the headphones, press the

Mute button on the remote. Any recording in progress

will not be affected. The MUTE message will appear

in the front-panel display as a reminder. To restore

the sound, press the Mute button again, or adjust the

volume.

Listening Through Headphones

Plug the 1/4-inch stereo plug on a pair of headphones

into the front-panel Phones jack for private listening.

•

For information about turning off the speakers

during headphone listening, see page 14.

Note

Selecting a Source

There are two different ways to select a source:

•

Rotate the front-panel INPUT SELECTOR.

•

Directly select any source by pressing its Source

Selector button on the remote.

The AVR selects the analog audio and video inputs

assigned to the source and any other settings you made

during setup.

The digital audio inputs are not assigned to any specic

sets of analog inputs. Once you select a source device

you can use the remote control’s Audio Input Select

(DIGITAL) button to select the specic audio input

connection (HDMI, coaxial digital, optical digital, analog)

that you want to listen to. (Note: You cannot select an

audio input connection for the FM/AM or USB source

buttons.)

The source name, the selected audio input and the

surround mode will appear on the front panel.

VideoTroubleshootingTips

If there is no picture:

•

Check the source selection.

•

Check all connections for a loose or incorrect

connection.

•

Check the video-input selection on the TV/display

device.

Additional Tips for Troubleshooting HDMI

Connections

•

Turn off all devices (including the TV, the AVR and

any source components).

•

Unplug the HDMI cables, starting with the cable

between the AVR and the TV, and continuing with the

cables between the AVR and each source device.

•

Carefully reconnect the cables from the source

devices to the AVR. Connect the cable from the AVR

to the TV last.

•

Turn on the devices in this order: TV, AVR, source

devices.

•

Depending upon the particular components

involved, the complexity of the required

communication between HDMI components may

cause delays of up to a minute in the completion

of some actions, such as input switching or

switching between SD and HD channels.

Note

Listening to FM and AM Radio

Select the AM/FM source. Use the Tuning Up/Down

buttons to tune a station, which will be shown on the

front-panel display.

For automatic tuning, press and hold the Tuning Up/

Down buttons to scan stations until a station with

acceptable signal strength is found. For manual tuning,

press each Tuning button until the desired station is

found. Using the FM Mono mode may improve the

reception of weaker stations.

Preset Stations

A total of 30 stations (AM and FM combined) may be

stored as presets. When the desired station has been

tuned in, press the Memory button and the preset

number will ash on the front-panel Message display.

Use the remote’s Number buttons to enter the desired

preset number.

To tune a preset station, press the Preset Up/Down

buttons or enter the preset number using the remote’s

Number buttons.

RDS

RDS(Radio Data System) is a method for sending

information signals together with the transmitter signals.

These codes contain Program Service name (PS), A list

of Program Types (PTY), Radio Text (RT).

17

Operation

English

•

RDS is available only in models that are

distributed in Europe.

•

RDS is only possible in the FM band.

•

RDS searches for the preset stations only. If no

stations have been stored in the memory, or if

the program type could not be found among the

preset stations, “NO PTY” is displayed.

Note

Listening to Media on a USB

Device

Your AVR is compatible with USB 2.0 or USB 1.1 media

in the FAT 16 or FAT 32 le format and is compatible

with the following MP3 and WMA media:

•

MP3:

Bit rates between 96 – 320kbps. Fixed bit-

rates at 44.1kHz sampling is recommended. Variable

bit-rates (VBR) are playable, but playing time may be

displayed incorrectly. Files must have a “.mp3” le

extension.

•

WMA:

Bit rates of 64kbps or higher. NOTE: Bit rates

of 80kbps and 256kbps are not compatible. Files

must have a “.wma” le extension.

A maximum number of 65,536 folders and les can be

supported.

PlayinglesonaUSBdevice

1

Insert the USB drive into the AVR’s front-panel

USB port.

•

Do not connect a personal computer or peripheral

to the USB port. USB hubs are not supported.

Caution

2

Select USB as the source device. “USB” will

appear on the front-panel display, and after the

AVR loads the contents of the current folder the

USB playback screen will appear on the OSD.

File

Type

Playback

Mode

Repeat

Mode

Artist Name

Album Title

Data

Rate

Elapsed

Time

Song Title

Use the remote’s Transport Control buttons to control

playback.

To browse the contents of the current folder, press the

remote’s RETURN button. The USB folder screen will

appear on the OSD for 20 seconds.

Use the remote’s UP/Down and ENTER buttons to

highlight and select tracks.

•

To prevent damage or malfunction, press the

remote’s Stop (■) Transport Control button before

removing the USB device from the AVR’s USB

port.

Caution

Selecting a Surround Mode

Selecting a surround mode can be as simple or

sophisticated as your individual system and tastes. Feel

free to experiment, and you may nd a few favorites

for certain sources or program types. You can nd

more detailed information on surround modes in Audio

Processing and Surround Sound, below.

To select a surround mode, press the Surround Mode

Select buttons. Each press advances to the next

available surround mode.

Digital surround-sound modes, such as Dolby Digital

and DTS systems, are available only with specially

encoded programs, such as those available via HDTV,

DVD and Blu-ray Disc media and digital cable or

satellite television. Other surround modes such as

Dolby Pro Logic II may be used with digital or analog

signals to create a different surround presentation or to

use a different number of speakers.

Surround mode selection depends upon the number

of speakers in your system, the programs you are

watching or listening to, and your personal tastes.

18

R-607/R-507AUDIO/VIDEORECEIVER

Advanced Functions

Much of the adjusting and conguration your AVR

requires is handled automatically, with little intervention

required on your part. You can also customize your AVR

to suit your system and your tastes. In this section, we

will describe some of the more advanced adjustments

available to you.

Audio Processing and Surround Sound

Audio signals can be encoded in a variety of formats

that affect not only the quality of the sound but also the

number of speaker channels and the surround mode.

You may also manually select a different surround

mode, when available.

Analog Audio Signals

Analog audio signals usually consist of two channels –

left and right. Your AVR offers several options for analog

playback:

•

Stereo:

When you want conventional 2-channel

playback, press the STEREO button. Sound will be

output from the front left and right speakers.

•

5-ChStereo:

When you want to hear stereo sound

through all of the system’s speakers (such as during

a party), select 5CH STEREO via the Surround Mode

Select buttons. This plays the left-channel signal

through the front left and surround left speakers,

the right-channel signal through the front right and

surround right speakers, and a summed mono signal

through the center speaker.

•

Analog Surround Modes:

Your AVR is able to

process 2-channel audio signals to produce multi-

channel surround sound, even when no surround

sound has been encoded in the recording. Among

the available modes are Dolby Pro Logic II, Dolby

Pro Logic, DTS Neo: 6, Theater, Hall, Stadium, Club

and Arena modes. Use the Surround Mode Select

buttons to select one of these modes.

Digital Audio Signals

Digital audio signals offer greater exibility and capacity

than analog signals and allow the encoding of up to 5.1

channels of discrete channel information directly into

the signal. The result is improved sound quality and

startling directionality, since each channel’s information

is transmitted independently of the other channels.

High-resolution recordings sound extraordinarily

distortion-free, especially in the high frequencies.

Digital surround-sound formats include Dolby Digital 2.0

(two channels only), Dolby Digital 5.1, Dolby Digital

EX, Dolby Digital Plus, Dolby TrueHD, DTS-HD High-

Resolution Audio, DTS-HD, DTS 5.1, DTS 96/24,

2-channel PCM modes in 44.1kHz, 48kHz, 88.1kHz,

96kHz or 176.4kHz, and 5.1 or 7.1 multichannel PCM.

(Your AVR will downmix the discrete surround back-

channel information in 6.1-channel and 7.1-channel

recordings into your system’s surround left and

surround right channels.)

Surround Mode Selection

Surround-mode selection depends upon the format

of the incoming audio signal as well as your personal

taste. Although there is never a time when all of the

AVR’s surround modes are available, the table below

indicates which surround modes are available for a

given input.

Input Signal

Format

Available Surround Modes

Dolby TrueHD

(Only for

R- 607),

Dolby Digital

Plus (Only

for R- 607),

Dolby Digital

(7.1-channel/

5.1-channel)

Corresponding Dolby TrueHD

(Only for R-607) or Dolby Digital

mode (Theater, Hall, Stadium,

Club, Arena and 5-Ch Stereo are

also available for 5.1-channel

programs)

Dolby Digital

(2.0-channel)

Dolby Pro Logic II Movie, Dolby

Pro Logic II Music, Dolby Pro

Logic II Game, Dolby Pro Logic

DTS-HD (Only

for R- 607),

DTS, DTS 96/24

Corresponding DTS Mode

(Theater, Hall, Stadium, Club,

Arena and 5-Ch Stereo are

also available for 5.1-channel

programs)

PCM

(2-channel),

Analog

(2-channel)

Dolby Pro Logic II Movie, Dolby

Pro Logic II Music, Dolby Pro

Logic II Game, Dolby Pro Logic,

DTS Neo:6 Cinema, DTS Neo:6

Music, Theater, Hall, Stadium,

Club, Arena, 5-Ch Stereo

MP3/WMA

Dolby Pro Logic II Movie, Dolby

Pro Logic II Music, Dolby Pro

Logic II Game, Dolby Pro Logic,

DTS Neo:6 Cinema, DTS Neo:6

Music, Theater, Hall, Stadium,

Club, Arena, 5-Ch Stereo

When in doubt, check the broadcast or the jacket

of your disc for more information on which surround

modes are available. Usually, nonessential sections of a

disc, such as trailers, extra materials or the disc menu,

are available only in Dolby Digital 2.0 (2-channel) or

PCM 2-channel mode. Look for an audio setup section

in the disc’s menu.

Also, make sure your disc player’s audio output is set to

the original bitstream rather than 2-channel PCM. Stop

play and check the player’s output setting.

19

Operation

English

AdjustingtheChannelVolumes

In addition to using the AVR’s built-in test noise to

congure the AVR for your speakers as explained

in

Congure the AVR for Your Speakers

, you can

also adjust the volume of any channel at any time to

compensate for individual program sources or your

personal taste.

1

Press the remote’s Channel Level button. The

Message Display will show the left channel

volume level.

2

Use the remote’s up and down arrow buttons to

display the channel you want to adjust.

3

Use the remote’s left and right arrow buttons to

adjust the channel’s volume.

Press the RETURN button when you’re nished.

Recording

Two-channel analog audio signals, as well as composite

video signals, are normally available at the appropriate

recording output connectors. To make a recording,

connect your audio or video recorder to the appropriate

AVR output connectors as described in the

Making

Connections

section, insert blank media in the recorder

and make sure the recorder is turned on and recording

while the source is playing. Refer to the recording

device’s instructions for complete information about

making recordings.

•

The AVR does not convert digital signals to

analog. Only devices connected to the analog

audio and composite video input connections can

be recorded.

•

HDMI video sources are not available for

recording.

•

Please make certain that you are aware of any

copyright restrictions on any material you record.

Unauthorized duplication of copyrighted materials

is prohibited by law.

Note

SleepTimer

The sleep timer sets the AVR to play for up to

90 minutes and then turn off automatically.

Press the Sleep button on the remote, and the time until

turn-off will be displayed on the front-panel Message

display The available settings are 30 min., 60 min.,

90 min. and OFF.

When the sleep timer has been set, a small crescent-

moon icon will appear on the front-panel display.

If you press the SLEEP button after the timer has been

set, the remaining play time will be displayed. Press the

SLEEP button again to change the play time.

Processor Reset

If the AVR behaves erratically after a power surge, rst

turn off the front-panel Main Power switch and unplug

the AC power cord for at least 3 minutes. Plug the cord

back in and turn the AVR on. If this procedure doesn’t

help, reset the AVR’s processor as described below.

•

Resetting the processor will erase all user

congurations, including speaker and level

settings, and tuner presets. After a reset, reenter

all of these settings from your notes in the

Appendix worksheets.

Note

ToresettheAVR’sprocessor:

1

Press the front-panel Standby/On switch to

place the unit in the Standby mode (the Standby

Indicator LED will turn red).

2

Press and hold the SURROUND down button on

the remote control as pressing and holding the

front-panel Standby/On switch simultaneously.

3

When the RESET message “RESET?” appears

on the front-panel Message display, press

BAND.

4

When the RESET message “OK?” appears on

the front-panel Message display, press BAND.

Memory

If the AVR is unplugged or experiences a power outage,

it will retain your user settings for up to two weeks.

20

Troubleshooting

If you experience any of the following difculties while using the system, use this troubleshooting guide to help

remedy the problem before requesting servicing. Should any problem persist, consult your nearest authorized dealer

or authorized independent company.

If the unit does not operate normally due to external inuence such as static electricity, disconnect the power plug

from the outlet and insert again to return to normal operating conditions.

Symptom Cause Solution

Unit does not function when

Main Power switch is turned

on.

•

No AC power.

•

Ensure that the power cord is plugged into

a live AC power outlet.

Front-panel Message display

lights, but there's no sound

or picture.

•

Intermittent input connection.

•

Mute is on.

•

Volume control is turned down.

•

Secure all input and speaker connections

•

Press Mute button.

•

Turn up Volume control.

No sound from any speaker.

•

Speakers set to “Off” in System

Setup menu.

•

Set speakers to “On” in System Setup

menu. See page 14, for more information.

No sound from any speaker;

PROTECT message appears

on Message display.

•

Amplier is in protection mode

due to possible short circuit.

•

Amplier is in protection mode

due to internal problems.

•

Check all speaker wires at speaker and

AVR connections for crossed wires.

•

Contact your local service center.

No sound from center or

surround speakers.

•

Incorrect surround mode.

•

Program material is

monophonic.

•

Incorrect speaker conguration.

•

Program material is stereo.

•

Select a surround mode other than stereo.

•

Mono programs contain no surround

information.

•

Check the speaker conguration in the

setup menu.

•

The surround decoder may not create

center- or surround-channel information

from non-encoded stereo programs.

Unit does not respond to

remote control commands.

•

Weak batteries in remote.

•

AVR not selected.

•

Remote sensor is obscured.

•

Change batteries in remote.

•

Press the Setup/AVR button.

•

Ensure that the AVR’s front-panel remote

sensor is in the line of sight of the remote.

Intermittent buzzing in tuner.

•

Local interference.

•

Move the AVR or antenna away from

computers, uorescent lights, motors or

other electrical appliances.

La page charge ...

Sherwood R-507 Operating Instructions Manual

Ce manuel convient également à

Sherwood R-507 Operating Instructions Manual

dans d''autres langues

Documents connexes

Autres documents