Denon AVR-1804 Le manuel du propriétaire

Catégorie
Récepteurs AV
Taper
Le manuel du propriétaire

Ce manuel convient également à

AV SURROUND RECEIVER
RÉCEPTEUR AUDIO-VIDÉO
AVR-1804/884
OPERATING INSTRUCTIONS
MODE D’EMPLOI
2 We greatly appreciate your purchase of the AVR-1804/884.
2 To be sure you take maximum advantage of all the features the AVR-1804/884 has to offer, read these instructions
carefully and use the set properly. Be sure to keep this manual for future reference should any questions or
problems arise.
2 Nous vous remercions de l’achat de l’AVR-1804/884.
2 Pour être sûr de profiter au maximum de toutes les caractéristiques qu’a à offrir l’AVR-1804/884, lire avec soin ces
instructions et bien utiliser l’appareil. Toujours conserver ce mode d’emploi pour s’y référer ultérieurement en cas
de question ou de problème.
FOR ENGLISH READERS PAGE 02 ~ PAGE 065, 128 ~ 132
POUR LES LECTEURS FRANCAIS PAGE 2, 66 ~ PAGE 132
ENGLISH
2
2 SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.
ATTENTION
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU
FOND.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
SERIAL NO.
PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE
CABINET FOR FUTURE REFERENCE
NO. DE SERIE
PRIERE DE NOTER LE NUMERO DE SERIE DE LAPPAREIL INSCRIT A LARRIERE
DU COFFRET DE FAÇON A POUVOIR LE CONSULTER EN CAS DE PROBLEME.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
FOR CANADA MODEL ONLY
POUR LES MODELE CANADIEN UNIQUEMENT
FRANCAIS
2 NOTE ON USE / OBSERVATIONS RELATIVES A LUTILISATION
Avoid high temperatures.
Allow for sufficient heat dispersion when
installed on a rack.
Eviter des températures élevées
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une étagère.
Handle the power cord carefully.
Hold the plug when unplugging the cord.
Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du cordon.
Keep the set free from moisture, water, and
dust.
Protéger l’appareil contre l’humidité, l’eau et
lapoussière.
Unplug the power cord when not using the set
for long periods of time.
Débrancher le cordon d’alimentation lorsque
l’appareil n’est pas utilisé pendant de longues
périodes.
* (For sets with ventilation holes)
Do not obstruct the ventilation holes.
Ne pas obstruer les trous d’aération.
Do not let foreign objects in the set.
Ne pas laisser des objets étrangers dans
l’appareil.
Do not let insecticides, benzene, and thinner
come in contact with the set.
Ne pas mettre en contact des insecticides, du
benzène et un diluant avec l’appareil.
Never disassemble or modify the set in any
way.
Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.
3
SAFETY INSTRUCTIONS
1. Read Instructions – All the safety and operating instructions
should be read before the product is operated.
2. Retain Instructions – The safety and operating instructions
should be retained for future reference.
3. Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions – All operating and use instructions should
be followed.
5. Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
6. Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7. Water and Moisture – Do not use this product near water – for
example, near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to the
product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product.
Any mounting of the product should follow the manufacturer’s
instructions, and should use a
mounting accessory
recommended by the
manufacturer.
9. A product and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the product and cart
combination to overturn.
10. Ventilation – Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
11. Power Sources – This product should be operated only from the
type of power source indicated on the marking label. If you are
not sure of the type of power supply to your home, consult your
product dealer or local power company. For products intended
to operate from battery power, or other sources, refer to the
operating instructions.
12. Grounding or Polarization – This product may be equipped with
a polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
13. Power-Cord Protection – Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where
they exit from the product.
15. Outdoor Antenna Grounding – If an outside antenna or cable
system is connected to the product, be sure the antenna or
cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article 810
of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See Figure A.
16. Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
17. Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
18. Overloading – Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of
fire or electric shock.
19. Object and Liquid Entry – Never push objects of any kind into
this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
20.
Servicing – Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
21.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service
personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance
– this indicates a need for service.
22. Replacement Parts – When replacement parts are required, be
sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics
as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
23. Safety Check – Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
24. Wall or Ceiling Mounting – The product should be mounted to a
wall or ceiling only as recommended by the manufacturer.
25. Heat – The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL
ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
ENGLISH
4
2
INTRODUCTION
2
ACCESSORIES
Thank you for choosing the DENON AVR-1804/884 Digital Surround A/V receiver. This remarkable component has been engineered to provide
superb surround sound listening with AV theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite
music sources.
As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the
contents of this manual before proceeding.
TABLE OF CONTENTS
z Before Using ...............................................................................................5
x Cautions on Installation...............................................................................5
c Cautions on Handling ..................................................................................5
v Features ......................................................................................................6
b Part Names and Functions......................................................................7, 8
n Read this first..............................................................................................9
m Setting up the Speaker Systems ................................................................9
, Connections........................................................................................10~18
. Using the Remote Control Unit ................................................................19
⁄0 Setting up the System........................................................................20~29
⁄1 Remote Control Unit...........................................................................30~34
⁄2 Operation ............................................................................................35~40
⁄3 Multi Zone...........................................................................................41, 42
⁄4 Surround .............................................................................................43~49
⁄5 DSP Surround Simulation ...................................................................50~53
⁄6 Listening to the Radio.........................................................................54~57
⁄7 Last Function Memory..............................................................................57
⁄8 Initialization of the Microprocessor ...........................................................57
⁄9 Additional Information.........................................................................58~63
¤0 Troubleshooting.........................................................................................64
¤1 Specifications ............................................................................................65
List of Preset Codes ..............................................................................128~132
Check that the following parts are included in addition to the main unit:
q Operating instructions .................................................................1
w Warranty......................................................................................1
e Service station list .......................................................................1
r Remote control unit (RC-939)......................................................1
rt y u
t R6P/AA batteries .........................................................................2
y AM loop antenna.........................................................................1
u FM indoor antenna ......................................................................1
ENGLISH
5
2
CAUTIONS ON INSTALLATION
Noise or disturbance of the picture may be generated if this unit or
any other electronic equipment using microprocessors is used near a
tuner or TV.
If this happens, take the following steps:
Install this unit as far as possible from the tuner or TV.
Set the antenna wires from the tuner or TV away from this unit’s
power cord and input/output connection cords.
Noise or disturbance tends to occur particularly when using indoor
antennas or 300 /ohms feeder wires. We recommend using
outdoor antennas and 75 /ohms coaxial cables.
For heat dispersal, leave at least 10 cm of space between the top,
back and sides of this unit and the wall or other components.
4 inch/10 cm or more
4 inch/10 cm or more
Wall
1
BEFORE USING
Pay attention to the following before using this unit:
Moving the set
To prevent short circuits or damaged wires in the connection cords,
always unplug the power cord and disconnect the connection cords
between all other audio components when moving the set.
Before turning the power switch on
Check once again that all connections are proper and that there are
not problems with the connection cords. Always set the power
switch to the standby position before connecting and disconnecting
connection cords.
Store this instructions in a safe place.
After reading, store this instructions along with the warranty in a
safe place.
Note that the illustrations in this instructions may differ from
the actual set for explanation purposes.
V. AUX jacks
The AVR-1804/884’s front
panel is equipped with a V.
AUX jacks. Remove the cap
covering the jacks when you
want to use it.
3
CAUTIONS ON HANDLING
Switching the input function when input jacks are not
connected
A clicking noise may be produced if the input function is switched
when nothing is connected to the input jacks. If this happens, either
turn down the MASTER VOLUME control or connect components
to the input jacks.
Muting of PRE OUT jacks, HEADPHONE jack and SPEAKER
terminals
The PRE OUT jacks, HEADPHONE jack and SPEAKER terminals
include a muting circuit. Because of this, the output signals are
greatly reduced for several seconds after the power switch is
turned on or input function, surround mode or any other-set-up is
changed. If the volume is turned up during this time, the output will
be very high after the muting circuit stops functioning. Always wait
until the muting circuit turns off before adjusting the volume.
Whenever the power switch is in the STANDBY state, the
apparatus is still connected on AC line voltage.
Please be sure to unplug the cord when you leave home for,
say, a vacation.
ENGLISH
6
4
FEATURES
1. Dolby Digital EX decoder system
Dolby Digital EX is a 6.1-channel surround format proposed by
Dolby Laboratories that allows users to enjoy in their homes the
“DOLBY DIGITAL SURROUND EX” audio format jointly developed
by Dolby Laboratories and Lucas Films and first used for the movie
“Star Wars Episode 1 – Phantom Menace”.
The 6.1 channels of sound, including surround back channels,
provide improved sound positioning and expression of space.
2. DTS-ES Extended Surround and DTS Neo:6
The AVR-1804/884 is compatible with DTS-ES Extended Surround, a
new multi-channel format developed by Digital Theater Systems Inc.
The AVR-1804/884 is also compatible with DTS Neo:6, a surround
mode allowing 6.1-channel playback of regular stereo sources.
3. Dolby Pro Logic
II decoder
Dolby Pro Logic II is a new format for playing multichannel audio
signals that offers improvements over conventional Dolby Pro
Logic. It can be used to decode not only sources recorded in Dolby
Surround but also regular stereo sources into five channels (front
left/right, center and surround left/right). In addition, various
parameters can be set according to the type of source and the
contents, so you can adjust the sound field with greater precision.
4. Multi Zone Music Entertainment System
Multi Source Function:
This unit’s Multi Source function lets you select different audio
sources for listening Different sources can thus be enjoyed in the
main room (MAIN) and the subroom (ZONE 2) simultaneously.
5. On Screen Diaplay
Troublesome operations such as adjusting the delay time and other
parameters according to the listening environment are greatly
simplified. The various parameters can be set simply by selecting
the graphic displayed on the monitor screen according to the
listening room’s system environment.
6. Video Conversion Function
The AVR-1804/884 is equipped with a function for converting the
signals input to the video input connector and S-Video input
connector. With this function, the AVR-1804/884’s monitor out
connector and the monitor (TV) can be connected with video pin-
plug cords or an S-Video connection cord.
7. Dolby Digital
Using advanced digital processing algorithms, Dolby Digital
provides up to 5.1 channels of wide-range, high fidelity surround
sound. Dolby Digital is the default digital audio delivery system for
North American DVD and DTV.
8. DTS (Digital Theater Systems)
DTS provides up to 5.1 channels of wide-range, high fidelity
surround sound, from sources such as laser disc, DVD and
specially-encoded music discs.
9. Component Video Switching
In addition to composite video and “S” video switching, the AVR-
1804/884 provides 2 sets of component video (Y, P
B/CB, PR/CR)
inputs assignable, and one set of component video outputs to the
television, for superior picture quality.
10.Auto Surround Mode
This function stores the surround mode last used for an input
signal in the memory and automatically sets that surround mode
the next time that signal is input.
7
5
PART NAMES AND FUNCTIONS
Front Panel
For details on the functions of these parts, refer to the pages given in parentheses ( ).
#4 #3
#2 #0#1
@9 @7@8 @6 @5 @4 @0 !9@2 @1@3
r y i !0 !2 !3 !5 !6 !7 !8q w
te u o !1 !4
q
Power ON/STANDBY switch .......................................(21, 35, 54)
w
Headphones jack (PHONES) ....................................................(39)
e
ZONE2/REC button..........................................................(40 ~ 42)
r
SPEAKER A button.............................................................(35, 57)
t
SPEAKER B button.............................................................(35, 57)
y
SURROUND BACK button .................................................(41, 48)
u
ANALOG button .................................................................(36, 38)
i
EXT. IN button ....................................................................(36, 38)
o
DOLBY/DTS SURROUND button.................................(43, 45, 48)
!0
5CH/6CH STEREO button ........................................................(50)
!1
DIRECT/STEREO button ....................................................(38, 50)
!2
TUNING UP/DOWN buttons ....................................................(55)
!3
V. AUX input jacks................................................................(5, 15)
!4
SURROUND MODE button .........................................(37, 48, 52)
!5
SURROUND PARAMETER button .....................................(45, 51)
!6
SELECT knob ...............................................................(37, 45, 52)
!7
TONE DEFEAT button ..............................................................(39)
!8
TONE CONTROL button ..........................................................(39)
!9
MASTER VOLUME control ......................................................(37)
@0
VIDEO SELECT button .............................................................(39)
@1
STATUS button .........................................................................(40)
@2
DIMMER button.......................................................................(40)
@3
MASTER VOLUME indicator....................................................(37)
@4
Display
@5
PRESET STATION select buttons.......................................(54, 56)
@6
BAND button............................................................................(55)
@7
OUTPUT indicator.....................................................................(41)
@8
SIGNAL indicator......................................................................(37)
@9
INPUT MODE indicator ............................................................(37)
#0
INPUT MODE button ...................................................(36, 38, 48)
#1
Remote control sensor (REMOTE SENSOR) ...........................(19)
#2
Power operation indicator ........................................................(35)
#3
FUNCTION knob ................................................................(36, 40)
#4
MAIN button.............................................................................(36)
ENGLISH
8
Remote control unit
For details on the functions of these parts, refer to the pages given in parentheses ( ).
SURROUND buttons .............(37, 43, 51)
Cursor buttons.................(20, 32, 44, 51)
Test tone button.................................(43)
Remote control signal
transmitter .........................................(19)
Master volume control
buttons.........................................(36, 42)
POWER buttons ..............(21, 31~33, 35)
MUTING button .................................(39)
Mode selector switches
............................(20, 30~32, 34, 35, 42)
Tuner system/
System buttons ...............(30, 33, 42, 55)
SYSTEM SET UP/
SETUP button ........................(20, 29, 32)
INPUT MODE selector
buttons.........................................(36, 38)
Input source selector buttons
.........................................(31~34, 36, 45)
SURROUND PARAMETER/SYSTEM
button...........................................(32, 45)
CH SELECT (channel select)/ ENTER
button ..............................(20, 32, 44, 46)
SURROUND BACK/RETURN
button ....................................(32, 41, 48)
DIMMER button.................................(40)VIDEO SELECT button.......................(39)
System buttons .....................(30, 32, 33)
LED (indicator) .............................(31, 34)
MULTI ZONE buttons ............(34, 41, 42) MAIN ZONE buttons....................(34, 42)
ON SCREEN/DISPLAY button
.....................................................(32, 40)
ENGLISH
SPEAKER button................................(35)
9
6
READ THIS FIRST
This AV Surround Receiver must be setup before use. Following these steps.
2 Speaker system layout
Basic system layout
The following is an example of the basic layout for a system consisting of 7 speaker systems and a television monitor:
7
SETTING UP THE SPEAKER SYSTEMS
Step 3 (page 20 to 29)
Finally, setting up the system.
Step 2 (page 19)
Next, insert the batteries into the remote control unit.
Step 1
(page 9 to 18)
Choose the best location to setup the Speakers and connecting the components.
Subwoofer Center speaker system
Surround speaker systems
Surround back speaker system
Front speaker systems
Set these at the sides of the TV or screen with
their front surfaces as flush with the front of the
screen as possible.
ENGLISH
10
R
L
R
L
R
INPUT OUTPUT
LRL
R
OUTPUT
L
R
L
INPUT
OPTICALCOAXIAL
OUTPUT
OPTICAL
L
R
L
R
L
R
L
R
OUTPUT
DIGITAL AUDIODIGITAL AUDIO
DIGITAL AUDIODIGITAL AUDIO
B
B
8
CONNECTIONS
Do not plug in the AC cord until all connections have been
completed.
Be sure to connect the left and right channels properly (left with
left, right with right).
Insert the plugs securely. Incomplete connections will result in the
generation of noise.
Use the AC OUTLETS for audio equipment only. Do not use
them for hair driers, etc.
Note that binding pin plug cords together with AC cords or placing
them near a power transformer will result in generating hum or
other noise.
Noise or humming may be generated if a connected audio
equipment is used independently without turning the power of this
unit on. If this happens, turn on the power of the this unit.
Connecting the audio components
When making connections, also refer to the operating instructions of the other components.
The power to these outlets is turned on and off when the power is switched between on and standby from the remote control unit or power
switch.
CD player
Connecting a CD player
Connect the CD player’s analog output jacks
(ANALOG OUTPUT) to this unit’s CD jacks using
pin plug cords.
Connecting a turntable
Connect the turntable’s output cord to the AVR-1804/884’s PHONO
jacks, the L (left) plug to the L jack, the R (right) plug to the right jack.
NOTES:
• This unit cannot be used with MC cartridges directly. Use a
separate head amplifier or step-up transformer.
If humming or other noise is generated when the ground wire
is connected, disconnect the ground wire.
Turntable
(MM cartridge)
Ground wire
Connect the internal amplifier’s subwoofer to the
subwoofer terminal. (Refer to page 17.)
AC OUTLETS
SWITCHED
(total capacity – 120 W (1 A.))
The power to these outlets is turned on and off in conjunction with the
POWER operation switch on the main unit, and when the power is switched
between on and standby from the remote control unit.
No power is supplied from these outlets when this unit’s power is at standby.
Never connect equipment whose total capacity is above 120 W (1 A.).
NOTE:
Only use the AC OUTLETS for audio equipment. Never use them for hair
driers, TVs or other electrical appliances.
Connecting the AC OUTLETS
AC CORD
AC 120 V, 60 Hz
Connecting a tape deck
Connections for recording:
Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s tape
recording (CDR/TAPE OUT) jacks using pin plug cords.
Connections for playback:
Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s tape
playback (CDR/TAPE IN) jacks using pin plug cords.
CD recorder or Tape deck
Route the connection cords, etc., in such a way
that they do not obstruct the ventilation holes.
MD recorder, CD recorder or other component
equipped with digital input/output jack
CD player or other
component equipped
with digital output jacks
Connecting the DIGITAL jacks
Use these for connections to audio (video) equipment with digital output. Refer to page 26
for instructions on setting this terminal.
NOTES:
Use 75 /ohms cable pin cords for coaxial connections.
Use optical cables for optical connections, removing the cap before connecting.
The main unit’s power must be turned on when recording via the AVR-1804/884.
NOTE:
If humming noise is generated by a
tape deck, etc., move the tape deck
away.
Subwoofer jack
ENGLISH
11
IN
VIDEO
R OUT IN
AUDIO
VIDEO
OUT IN
LRL
R
L
R
L
R OUT IN
AUDIO
VIDEO
OUT IN
LRL
R
L
R
L
R OUT
VIDEO
OUT
L
AUDIO
L
R
R OUT
VIDEO
OUT
L
AUDIO
L
R
R
L
R
L
R
L
R
L
R
L
RL
B
B
Connecting video components
To connect the video signal, connect using a 75 /ohms video signal cable cord. Using an improper cable can result in a drop in video quality.
When making connections, also refer to the operating instructions of the other components.
The AVR-1804/884 is equipped with a function for up-converting video signals.
The signal connected to the video signal terminal is output to the S-Video monitor out terminals.
The REC OUT terminals have no conversion function, so when recording only connect the video terminals.
TV or DBS tuner
Connecting a TV/DBS tuner
TV/DBS
• Connect the TV’s or DBS tuner’s video output jack (VIDEO OUTPUT) to the
(yellow) TV/DBS IN jack using a 75 /ohms video coaxial pin plug
cord.
Connect the TV’s or DBS tuner’s audio output jacks (AUDIO OUTPUT) to
the TV/DBS IN jacks using pin plug cords.
AUDIO
VIDEO
DVD player or video disc player (VDP), etc.
Connecting a DVD player or a video disc player (VDP)
DVD
Connect the video disc player’s video output jack (VIDEO OUTPUT) to the (yellow)
DVD/VDP IN jack using a 75 /ohms video coaxial pin plug cord.
• Connect the video disc player’s analog audio output jacks (ANALOG AUDIO OUTPUT) to the
DVD/VDP IN jacks using pin plug cords.
• It is also possible to connect a video disc player, DVD player, video game, etc., to the VCR-2
jacks.
AUDIO
VIDEO
Monitor TV
MONITOR OUT
• Connect the TV’s video input jack (VIDEO INPUT) to the
MONITOR OUT jack using a 75 /ohms video
coaxial pin plug cord.
VIDEO
Note on connecting the digital input jacks
Only audio signals are input to the digital input jacks.
For details, see pages 10, 26.
Video deck 2
Video deck 1
Connecting a video decks
• There are two sets of video deck (VCR) jacks, so two video decks can be connected for simultaneous recording or video copying.
Video input/output connections:
Connect the video deck’s video output jack (VIDEO OUT) to the (yellow) VCR-1 IN jack, and the video deck’s video input jack (VIDEO IN) to the
(yellow) VCR-1 OUT jack using 75 /ohms video coaxial pin plug cords.
Connecting the audio output jacks
• Connect the video deck’s audio output jacks (AUDIO OUT) to the VCR-1 IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the VCR-1
OUT jacks using pin plug cords.
Connect the second video deck to the VCR-2 jacks in the same way.
AUDIOAUDIO
VIDEOVIDEO
Connecting a Monitor TV
ENGLISH
12
IN
S-VIDEO
OUT
S-VIDEO
OUT
S-VIDEO
IN OUT
S-VIDEO
IN OUT
S-VIDEO
B
B
Connecting a video component equipped with S-Video jacks
When making connections, also refer to the operating instructions of the other components.
A note on the S input jacks
The input selectors for the S inputs and pin jack inputs work in conjunction with each other.
The AVR-1804/884 is equipped with a function for converting video signals.
The signal connected to the S-Video signal terminal is output to the composite video monitor out terminals.
The REC OUT terminals have no conversion function, so when recording only connect the S-Video terminals.
DVD player or video disc player (VDP)
Connecting a DVD player or a video disc player (VDP)
DVD
Connect the DVD/VDP player’s S-Video output jack to the S-VIDEO
DVD/VDP IN jack using an S-Video connection cord.
It is also possible to connect a video disc player, DVD/VDP player,
video camcorder, game machine, etc., to the VCR-2 jacks.
Connecting a monitor TV
MONITOR OUT
• Connect the TV’s S video input (S-VIDEO INPUT) to the
MONITOR OUT jack using a S jack connection
cord.
S-VIDEO
Monitor TV
Connecting a TV/DBS tuner
• Connect the TV’s or DBS tuner’s S video output jack (S-VIDEO
OUTPUT) to the TV/DBS IN jack using an S jack
connection cord.
S-VIDEO
TV or satellite broadcast tuner
Video deck 2
Connecting the video decks
• Connect the video deck’s S output jack (S-OUT) to the
VCR-1 IN jack and the video deck’s S input jack (S-IN) to the
VCR-1 OUT jack using S jack connection cords.
• Connect the video deck’s S output jack (S-OUT) to the
VCR-2 IN jack and the video deck’s S input jack (S-IN) to the
VCR-2 OUT jack using S jack connection cords.
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
Video deck 1
Connect the components’ audio inputs and outputs as described on page 11.
ENGLISH
13
VIDEO OUT
Y
CRCB
COMPONENT
B
VIDEO IN
Y
CRCB
COMPONENT
When making connections, also refer to the operating instructions of the other components.
The signals input to the color difference (component) video jacks are not output from the VIDEO output jack (yellow) or the S-Video output jack.
In addition, the video signals input to the VIDEO input (yellow) and S-Video input jacks are not output to the color difference (component) video
jacks.
Some video sources with component video outputs are labeled Y, CB, CR, or Y, Pb, Pr, or Y, R-Y, B-Y. These terms all refer to component video
color difference output.
At SYSTEM SETUP, the component video input terminal can be assigned for the input sources to which you want to connect AV devices. (For
details, see page 26.)
DVD player
Connecting a DVD player
DVD IN jacks
Connect the DVD player’s color difference (component) video output jacks
(COMPONENT VIDEO OUTPUT) to the COMPONENT DVD IN jack using 75 /ohms
coaxial video pin-plug cords.
In the same way, another video source with component video outputs such as a
TV/DBS tuner, etc., can be connected to the TV/DBS color difference (component)
video jacks.
Monitor TV
Connecting a monitor TV
MONITOR OUT jack
Connect the TV’s color difference (component) video input jacks
(COMPONENT VIDEO INPUT) to the COMPONENT MONITOR OUT jack
using 75 /ohms coaxial video pin-plug cords.
The color difference input jacks may be indicated differently on
some TVs, monitors or video components (“C
R, CB and Y”, “R-
Y, B-Y and Y”, “Pr, Pb and Y”, etc.). For details, carefully read the
operating instructions included with the TV or other component.
Connecting a Video Component Equipped with Color Difference (Component - Y, PR/CR, PB/CB)
Video Jacks (DVD Player)
Video Conversion signals
ENGLISH
Signal input to the AVR-1804/884
Video signal output to VIDEO
MONITOR OUT jack (yellow)
Video signal output to S-Video
MONITOR OUT jack
Video signal output to color
difference (component) Video
MONITOR OUT jack
Monitor Output jacks
Video signal input jack
C
C
(Up-conversion)
E
S-Video signal input jack
C
(Down-conversion)
CE
Color difference (component)
Video signal input jack
EEC
(C : Video signal output, E : Video signal not output)
14
Connecting the antenna terminals
DIRECTION OF
BROADCASTING
STATION
75 /ohms
COAXIAL
CABLE
FM ANTENNA
FM INDOOR
ANTENNA
(Supplied)
AM LOOP
ANTENNA
(Supplied)
AM OUTDOOR
ANTENNA
GROUND
FM ANTENNA
ADAPTER
FEEDER
CABLE
1
4
2
3
AM loop antenna assembly
Connect to the AM
antenna terminals.
Bend in the reverse
direction.
Remove the vinyl tie
and take out the
connection line.
a. With the antenna
on top any stable
surface.
b. With the antenna
attached to a
wall.
Mount
Installation hole Mount on wall, etc.
Connection of AM antennas
1. Push the
lever.
2. Insert the
conductor.
3. Return the
lever.
Note to CATV system installer:
This reminder is provided to call the CATV system installers
attention to Article 820-40 of the NEC which provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
Notes:
Do not connect two FM antennas simultaneously.
Even if an external AM antenna is used, do not disconnect the
AM loop antenna.
Make sure AM loop antenna lead terminals do not touch metal
parts of the panel.
ENGLISH
15
L
R
L
R
Connecting the external input (EXT. IN) jacks
These jacks are for inputting multi-channel audio signals from an outboard decoder, or a component with a different type of multi-channel
decoder, such as a DVD Audio player, or a multi-channel SACD player, or other future multi-channel sound format decoder.
When making connections, also refer to the operating instructions of the other components.
Decoder with 6-
channel analog output
Front
Surround
Subwoofer
Center
For instructions on playback using the external input (EXT. IN) jacks, see page 38.
Connecting the video component equipped with a V. AUX jacks
To connect the video signal, connect using a 75 /ohms video signal cable cord. Using an improper cable can result in a drop in sound quality.
R VIDEO OUT S-VIDEO OUTOPTICALL
R VIDEO OUTL
OUTPUT
OUTPUT
LINE OUT
DIGITAL OUT
VIDEO OUT
S-VIDEO OUT
VIDEO OUT
LINE OUT
S-VIDEO OUT
S-VIDEO OUT
L
R
L
R
L
R
Connecting a Video game component
Connect the Video game components output jacks to
this units V. AUX INPUT jacks.
Video game
Video camera
Connecting a video camera component
Connect the video camera components output jacks to
this units V. AUX INPUT jacks.
The V. AUX jacks is covered with a cap. Remove this cap in order to use the terminal. (See page 5 for instructions on removing the cap.)
ENGLISH
16
Connecting the ZONE2 jacks
If another pre-main (integrated) amplifier is connected, the ZONE2 jacks can be used to play a different program source in ZONE2 at the same
time.
L
R
++
OUTPUT
INPUT
AUX OUT
B
ZONE2
RC-616
INFRARED RETRANSMITTER
Integrated pre-main amplifier
RC-617
INFRARED SENSOR
Extension jacks for future use.
Speaker system connections
Connect the speaker terminals with the speakers making sure that
like polarities are matched ( with , with ). Mismatching of
polarities will result in weak central sound, unclear orientation of
the various instruments, and the sense of direction of the stereo
being impaired.
When making connections, take care that none of the individual
conductors of the speaker cord come in contact with adjacent
terminals, with other speaker cord conductors, or with the rear
panel.
NOTE:
NEVER touch the speaker terminals when the power is on.
Doing so could result in electric shocks.
Speaker Impedance
When speaker systems A (
I) and B (II) are use separately, speakers
with an impedance of 6 to 16 /ohms can be connected for use as
front and surround back/ZONE2 speakers.
Be careful when using two pairs of front and Surround Back/ZONE2
speakers (A + B) and (I + II) at the same time, since use of
speakers with an impedance of 12 to 16 /ohms.
Speakers with an impedance of 6 to 16 /ohms can be connected
for use as center and surround speakers.
The protector circuit may be activated if the set is played for long
periods of time at high volumes when speakers with an impedance
lower than the specified impedance are connected.
Connecting the speaker cords
1. Loosen by turning
counterclockwise.
2. Insert the cord. 3. Tighten by turning
clockwise.
Connecting banana plugs
Turn clockwise to tighten, then insert the
banana plug.
Banana plug
1. Push the lever. 2. Insert the cord. 3. Return the lever.
ENGLISH
17
(
I
) (
II
)
(
L
) (
R
) (
L
) (
R
)
(
L
) (
R
)
Connections
When making connections, also refer to the operating instructions of the other components.
Connection jack for subwoofer with
built-in amplifier (super woofer), etc.
CENTER SPEAKER
SYSTEM
SURROUND BACK/MULTI ZONE SPEAKER SYSTEMS
SURROUND SPEAKER
SYSTEMS
Precautions when connecting speakers
If a speaker is placed near a TV or video monitor, the colors on the screen may be disturbed by the speakers magnetism. If this should
happen, move the speaker away to a position where it does not have this effect.
NOTES:
To use Surround back with one speaker,
connect the speaker to SURR. BACK (I).
The settings must be changed to use this
speaker for ZONE2. (See page 28)
The same signal is output simultaneously
to the SURR.BACK/ZONE2 I and II
terminals.
FRONT SPEAKER
(B) SYSTEMS
FRONT SPEAKER
(A) SYSTEMS
ENGLISH
18
This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under
circumstances such as when the output of the power amplifier is inadvertently short-circuited and a large current flows, when
the temperature surrounding the unit becomes unusually high, or when the unit is used at high output over a long period
which results in an extreme temperature rise.
When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED flashes. Should
this occur, please follow these steps: be sure to switch off the power of this unit, check whether there are any faults with
the wiring of the speaker cables or input cables, and wait for the unit to cool down if it is very hot. Improve the ventilation
condition around the unit and switch the power back on.
If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the
unit, switch off the power and contact a DENON service center.
Protector circuit
The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with an
impedance lower than the specified impedance (for example speakers with an impedance of lower than 4 /ohms) are
connected. If the protector circuit is activated, the speaker output is cut off. Turn off the sets power, wait for the set to cool
down, improve the ventilation around the set, then turn the power back on.
Note on speaker impedance
ENGLISH
19
9
USING THE REMOTE CONTROL UNIT
Following the procedure outlined below, insert the batteries before using the remote control unit.
Range of operation of the remote control unit
Inserting the batteries
Point the remote control unit at the remote control sensor as shown
on the diagram at the left.
NOTES:
The remote control unit can be used from a straight distance of
approximately 23 feet/7 meters, but this distance will shorten or
operation will become difficult if there are obstacles between the
remote control unit and the remote control sensor, if the remote
control sensor is exposed to direct sunlight or other strong light, or
if operated from an angle.
Neon signs or other devices emitting pulse-type noise nearby may
result in malfunction, so keep the set as far away from such
devices as possible.
Approx. 23 feet/7 m
30°
30°
w Insert the R6P/AA batteries properly, as
shown on the diagram.
q Press as shown by the arrow and slide
off.
e Close the lid.
NOTES:
Use only R6P/AA batteries for replacement.
Be sure the polarities are correct. (See the illustration inside the battery compartment.)
Remove the batteries if the remote control transmitter will not be used for an extended period of time.
If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the
battery compartment thoroughly before installing new batteries.
Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the time comes.
Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is
operated nearby the set. (The included battery is only for verifying operation. Replace it with a new battery as soon as possible.)
ENGLISH
20
10
SETTING UP THE SYSTEM
Once all connections with other AV components have been completed as described in CONNECTIONS (see pages 10 to 18), make the
various settings described below on the display.
These settings are required to set up the listening rooms AV system centered around the this unit.
Use the following buttons to set up the system:
SYSTEM SETUP button
Press this to display the system setup on the display.
CURSOR buttons (, ª, 0, 1)
Press this change what appears on the display.
ENTER button
Press this to switch the display.
Also use this button to complete the setting.
1
Set the slide switch to AUDIO.
2
Use the following buttons to set up the system:
System setup items and default values (set upon shipment from the factory)
System setup Default settings
Speaker
Configuration
Subwoofer mode
Digital In
Assignment
Auto Surround
Mode
Input the combination of speakers in your system and their
corresponding sizes (SMALL for regular speakers, LARGE for full-
size, full-range) to automatically set the composition of the signals
output from the speakers and the frequency response.
This selects the subwoofer speaker for playing deep bass signals.
This assigns the digital input jacks for the different
input sources.
Auto surround mode function setting.
Input source
Digital
Inputs
Front Sp.
Large
Center Sp. SubwooferSurround Sp.
Small YesSmall
LFE (Normal)
Front L Center Surround Back
12 ft 12 ft 10 ft
CD DVD/VDP TV/DBS
VCR-1
VCR-2 CDR/TAPE
COAXIAL OPTICAL 1 OPTICAL 2 OFF OFF OPTICAL 3
Auto Surround Mode = ON
Surround Back Sp.
Small
Delay Time
This parameter is for optimizing the timing with which the audio
signals are produced from the speakers and subwoofer according
to the listening position.
Subwoofer
12 ft
Crossover
Frequency
Set the frequency (Hz) below which the bass sound of the various
speakers is to be output from the subwoofer.
80 Hz
Video In
Assignment
This assigns the component video input jacks for
the different video input sources.
Input source
Component
Inputs
DVD/VDP TV/DBS
VCR-1
VCR-2 V. AUX
VIDEO 1 VIDEO 2 OFF OFF OFF
Ext. In SW Level Set the Ext. In Subwoofer channel playback level. Ext. In SW Level = +15 dB
Power AMP
Assignment
Set this to switch the surround back channels power amplifier for
use for Zone 2.
Surround Back
On Screen
Display
This sets whether or not to display the on-screen display that
appears on the monitor screen when the controls on the remote
control unit or main unit are operated.
ON
Auto Tuner
Presets
FM stations are received automatically and stored in the memory.
A1 ~ A8
B1 ~ B8
C1 ~ C8
D1 ~ D8
E1 ~ E8
87.5/89.1/98.1/107.9/90.1/90.1/90.1/90.1 MHz
520/600/1000/1400/1500/1710 kHz, 90.1/90.1 MHz
90.1 MHz
90.1 MHz
90.1 MHz
ENGLISH
Front L Front R Center
0 dB 0 dB 0 dB
Test Tone
This adjusts the volume of the signals output from the speakers
and subwoofer for the different channels in order to obtain
optimum effects.
Surround L
0 dB
Surround R
0 dB
Surround Back
0 dB
Subwoofer
0 dB
Front R
12 ft
Surround L
10 ft
Surround R
10 ft
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136

Denon AVR-1804 Le manuel du propriétaire

Catégorie
Récepteurs AV
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues