Samsung HW-J7500R Manuel utilisateur

User manual

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at

www.samsung.com/register

HW-J7500R

HW-J7501R

2

GETTING STARTED

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage is

present inside. It is dangerous to make any kind

of contact with any internal part of this product.

This symbol indicates that important literature

concerning operation and maintenance has

been included with this product.

Class II product : This symbol indicates that a safety connection to electrical earth (ground) is not required.

AC voltage : Rated voltage marked with this symbol is AC voltage

DC voltage : Rated voltage marked with this symbol is DC voltage.

Caution. Consult instructions for use : This symbol instructs the user to consult the user manual for

further safety related information.

WARNING : To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• This apparatus shall always be connected to a AC outlet with a protective grounding connection.

• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the

mains plug shall be readily operable.

CAUTION

• Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases on the

apparatus.

• To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power

plug must be easily and readily accessible at all times.

GETTING STARTED

ENG

3

GETTING STARTED

WARNING: DO NOT INGEST BATTERY. CHEMICAL BURN HAZARD. The remote control supplied with

this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause

severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from

children. If the battery compartment does not close securely, stop using the remote and make sure to

keep it away from children. If you think the battery might have been swallowed or placed inside any part of the body,

seek immediate medical attention.

PRECAUTIONS

99.1mm 99.1mm

68.6

mm

99.1mm

Ensure that the AC power supply in your house complies with the power requirements listed on the identification sticker

located on the back of your product. Install your product horizontally, on a suitable base (furniture), with enough space

around it for ventilation (7~10 cm). Make sure the ventilation slots are not covered. Do not place the unit on amplifiers or

other equipment which may become hot. This unit is designed for continuous use. To fully turn off the unit, disconnect

the AC plug from the wall outlet. Unplug the unit if you intend to leave it unused for a long period of time.

During thunderstorms, disconnect the AC plug from the

wall outlet. Voltage peaks due to lightning could damage

the unit.

Protect the product from moisture (i.e. vases), and

excess heat (e.g. a fireplace) or equipment creating

strong magnetic or electric fields. Unplug the power

cable from the AC wall socket if the unit malfunctions.

Your product is not intended for industrial use. It is for

personal use only. Condensation may occur if your

product has been stored in cold temperatures. If

transporting the unit during the winter, wait approximately

2 hours until the unit has reached room temperature

before using.

Do not expose the unit to direct sunlight or other heat

sources. This could lead to overheating and cause the

unit to malfunction.

The battery used with this product contains chemicals

that are harmful to the environment. Do not dispose of

the battery in the general household trash. Do not

expose the battery to excess heat, direct sunlight, or fire.

Do not short circuit, disassemble, or overheat the battery.

Danger of explosion if the battery is replaced incorrectly.

Replace only with the same or equivalent type.

4

GETTING STARTED

● Figures and illustrations in this User Manual are

provided for reference only and may differ from

actual product appearance.

● An administration fee may be charged if either

(a) an engineer is called out at your request and

there is no defect with the product (i.e. where

the user manual has not been read).

(b) you bring the unit to a repair centre and there is

no defect with the product (i.e. where the user

manual has not been read).

● You will be informed of the administration fee

amount before a technician visits.

CONTENTS

2 GETTING STARTED

2 Safety Information

5 What’s Included

6 DESCRIPTIONS

6 Top / Front Panel

7 Rear / Bottom Panel

8 Remote Control

10 INSTALLATION

10 Installing the Soundbar

10 Installing the Wall Mount

14 Placing the Soundbar on a TV stand

16 Installing the Soundbar as a Free-Standing

Unit

16 Assembling the Clamp-Wire

17 CONNECTIONS

17 Connecting the Subwoofer

19 Connecting to a TV

19 TV SoundConnect

20 Connecting to a TV Using an HDMI (Digital)

Cable

20 Connecting to a TV Using a Digital Optical

Cable

21 Connecting to External Devices

21 HDMI Cable

22 Optical or Analogue Audio Cable

23 FUNCTIONS

23 Input Mode

24 Bluetooth

26 Using the Multiroom App

28 Using the Network Standby On

Function

29 Software Update

31 TROUBLESHOOTING

31 Troubleshooting

32 APPENDIX

32 Specifications

ENG

5

GETTING STARTED

WHAT’S INCLUDED

BEFORE READING THE USER’S MANUAL

Note the following terms before reading the user manual.

+ Icons used in this manual

Icon Term Definition

Caution

Indicates a situation where a function does not operate or settings may be cancelled.

Note

Indicates tips or instructions on the page that help you operate a function.

Check for the supplied accessories shown below.

Remote Control /

Lithium Battery (3V : CR2032)

Power Cord : 2 EA AC/DC Adapter

Clamp-Wire Wall-Mount Bracket Holder-Screw 1 : 4 EA

Holder-Screw 2 : 4 EA Holder-Fix Mount Holder-Foot : 3 EA

● The appearance of the accessories may differ slightly from the illustrations above.

6

DESCRIPTIONS

TOP / FRONT PANEL

(Power) Button

Turns the power on and off.

VOL. - / +

Controls the volume level.

The numeric value of the volume level

appears in the front panel display.

Display

Displays the current mode.

(Source) Button

Selects the D.IN, AUX, HDMI, BT, or TV input.

● While the unit is powered on, pressing the

button for more than 3 seconds sets

the button to act as the

(Mute) button.

To cancel the

(Mute) button setup, press

the

button for more than 3 seconds

again.

● To clean this apparatus, unplug the power cord from the wall outlet and wipe the product using a soft, dry

cloth. Due to aluminum being a positive electrostatic material, static discharge may occur.

● When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

● When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

● If you want to enjoy sound only from the Soundbar, you must turn off the TV's speakers in the Audio Setup

menu of your TV. Refer to the owner's manual supplied with your TV.

DESCRIPTIONS

ENG

7

DESCRIPTIONS

REAR / BOTTOM PANEL

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

SERVICE

SPK ADDWi-Fi SETUP

DC 24V

SPK ADDWi-Fi SETUP

DC 24V

SERVICE

DC 24V

(Power Supply In)

Connect the DC power

adaptor to the power

supply jack, and then

connect the AC power

adaptor plug to a wall

outlet.

SPK ADD

Press the button to

connect the Soundbar to a

Samsung HUB (purchased

separately) or a network.

(Requires a smart device

and the Samsung

Multiroom app.

See page 26.)

Wi-Fi SETUP

Press this button to

connect your Soundbar to

your network using Wi-Fi

setup. (Requires a smart

device and the Samsung

Multiroom app.

See page 26.)

SERVICE

To upgrade the product's

software through the USB

Port.

OPTICAL IN (D.IN)

Connect to the digital (optical) output of an external device.

HDMI OUT (TV-ARC)

Outputs digital video and audio signals simultaneously using an

HDMI cable.

HDMI IN

Inputs digital video and audio signals simultaneously using an HDMI

cable. Use when connecting a supported external device.

AUX IN

Connect to the Analogue output of an external device.

LAN

Lets you connect to a network using a LAN cable.

LABEL

● When disconnecting the power cable of the AC power adaptor from a wall outlet, pull the plug.

Do not pull the cable.

● Do not connect this unit or other components to an AC outlet until all connections between components

are complete.

● Make sure to rest the AC/DC Adapter flat on a table or the floor. If you place the AC/DC Adapter so that it

is hanging with the AC cord input facing upwards, water or other foreign substances could enter the

Adapter and cause the Adapter to malfunction.

8

DESCRIPTIONS

REMOTE CONTROL

Anynet+

Press the Anynet+ button to turn the Anynet+ function on or off.

(Default : Auto Power Link OFF, ON - ANYNET+ / OFF - POWER LINK or OFF

- ANYNET+ / ON - POWER LINK). The Anynet+ function lets you control the

Soundbar with the remote from an Anynet+ compatible Samsung TV.

The Soundbar must be connected to the TV via an HDMI cable.

* Auto Power Link

Synchronizes the Soundbar to a connected Optical source via the Optical

jack so it turns on automatically when you turn on your TV. (See page 21)

Auto Power Link function is only available in the D.IN mode.

You can also activate Wi-Fi SETUP function by pressing and holding Anynet+

button on the remote for over 7 seconds.

Repeat

The Repeat function is available only when playing back music from Songs on phone

or DMS of Samsung Multiroom app.

OFF - REPEAT : Cancells Repeat Playback.

TRACK - REPEAT : Plays a track repeatedly.

ALL - REPEAT : Plays all tracks repeatedly.

Mute

You can turn the volume down to 0 with the push of a button.

Press again to restore the sound to the previous volume level.

SOURCE

Press to select a source connected to the Soundbar.

Skip Forward

If there is more than one file on the device you are playing, and you press

the ] button, the next file is selected.

SOUND CONTROL

Press to select TREBLE, BASS, or AUDIO SYNC. Then, use the

[

,

]

buttons to adjust the TREBLE or BASS volume from -3 ~ +3.

Press and hold the SOUND CONTROL button for about 5 seconds to adjust

the sound for each frequency band. 150Hz, 300Hz, 600Hz, 1.2KHz, 2.5KHz,

5KHz, and 10KHz are selectable and each can be adjusted to a setting between

-6 ~ +6.

If the Soundbar is connected to a digital TV and the video appears out of sync

with the audio, press the SOUND CONTROL button to sync the audio with the

video. Use the

[

,

]

buttons to set the audio delay between 0 ms ~ 300 ms.

In TV mode, and BT mode, the Audio Sync function may not available.

● Operate the TV using the TV's remote control.

ENG

9

DESCRIPTIONS

STREAMING MUSIC

Press STREAMING MUSIC button to listen to an Internet radio station. Each

time you press this button, the Soundbar switches to the next default station,

cycling through the 3 default stations.

To use the STREAMING MUSIC function, the Soundbar must be connected to

the Internet. (See page 28)

DRC (Dynamic Range Control) *

Lets you apply dynamic range control to Dolby Digital.

Press and hold the STREAMING MUSIC button to toggle the DRC (Dynamic

Range Control) function ON and OFF.

WOOFER

Press the WOOFER button. Then, use the

[

,

]

buttons to adjust the

Subwoofer volume from -12, -6 ~ +6.

You can also activate SPK ADD function of the Soundbar by pressing and

holding WOOFER button of the remote for over 5 seconds.

SOUND

Surround Sound adds depth and spaciousness to the sound. Pressing the

SOUND button repeatedly cycles through the Surround Sound settings :

ON - SURROUND SOUND, OFF - SURROUND SOUND

Volume

Adjusts the volume level of the unit.

Power

Turns the Soundbar on and off.

SOUND EFFECT

You can select from 6 sound modes - STANDARD (Original Sound), MUSIC,

CLEAR VOICE, SPORTS, MOVIE, and NIGHT MODE - depending on the

content you want to listen to.

Select the STANDARD mode if you want to enjoy the original sound.

Play / Pause

Press the

p

button to pause a file temporarily.

Press the

p

button again to play the selected file.

Skip Back

If there is more than one file on the device you are playing, and you press the

[

button, the previous file is selected.

INSTALLING THE BATTERY IN THE REMOTE CONTROL

1. Use a suitable coin to turn the

remote control's battery cover

counterclockwise to remove it

as shown in the figure above.

2. Insert a 3V lithium battery. Keep the

positive (+) pole facing up when inserting

the battery. Put the battery cover on and

align the '●' marks side by side as

shown in the figure above.

3. Use a suitable coin to

turn the remote control

battery cover clockwise

as far as it will go to fix it

in place.

10

INSTALLATION

INSTALLING THE SOUNDBAR

INSTALLING THE WALL MOUNT

+ Installation Precautions

● Install on a vertical wall only.

● For the installation, avoid a location with high temperature or humidity, or a wall that cannot sustain the weight of

the set.

● Check the strength of the wall. If the wall is not strong enough to support the unit, reinforce the wall or install the

unit on a different wall that can support the unit's weight.

● Purchase and use the fixing screws or anchors appropriate for the kind of wall you have (plaster board, iron board,

wood, etc.). If possible, fix the support screws into wall studs.

● Purchase wall mounting screws according to the type and thickness of the wall you will mount the Soundbar on.

- Diameter : M5

- Length: 35 mm or longer recommended.

● Connect cables from the unit to external devices before you install it on the wall.

● Make sure the unit is turned off and unplugged before you install it. Otherwise, it may cause an electric shock.

Check for the supplied accessories shown below.

Holder-Screw 1 : 4 EA Holder-Screw 2 : 4 EA Wall-Mount Bracket Holder-Fix Mount

INSTALLATION

ENG

11

INSTALLATION

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

5V 0.5A

SPK ADDWi-Fi SETUP

DC 24V

SERVICE

SPK ADDWi-Fi SETUP

DC 24V

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

1. Place the Soundbar as shown in the illustration, ensuring that none of the buttons touch the surface it is

lying on.

2. If the Holder-Foot (3 EA) and Holder-Support (2 EA) are attached, remove them.

Holder-Foot Holder-Support

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

SERVICE

SPK ADDWi-Fi SETUP

DC 24V

SERVICE

SPK ADDWi-Fi SETUP

DC 24V

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

3. Fix Holder-Screw 1 (4 EA) and Holder-Screw 2 (for main unit fixing) (4 EA) into the holes of the Soundbar tightly

as shown in the illustration.

12

INSTALLATION

Wall

4. Insert the Wall-Mount Screws into the 3 holes one by one to fix the Wall-Mount Bracket on the wall.

● Recommended screw : M5

1

2

5. Mount the Soundbar on the Wall-Mount Bracket in order of the following illustration (1  2).

ENG

13

INSTALLATION

6. Fix the Holder-Fix Mount (for wall-mount fixing) to join the Wall-Mount Bracket with the Soundbar.

● Wall-Mount Screws are not provided.

● Since different types of wall-mount screws are required depending on your wall, you should check your wall

before installation and purchase the appropriate wall-mount screws to use.

14

INSTALLATION

PLACING THE SOUNDBAR ON A TV STAND

Place the Soundbar on a TV stand.

Check for the supplied accessories shown below.

Holder-Foot : 3EA Holder-Screw 2 : 3EA

5V 0.5A

SPK ADDWi-Fi SETUP

DC 24V

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

5V 0.5A

SPK ADDWi-Fi SETUP

DC 24V

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

2

1

1. Place the Soundbar as shown in the illustration, ensuring that none of the buttons touch the surface it is

lying on. You can use the Soundbar’s packaging to support its two ends.

2. Attach the Holder-Foot (3 EA) to the Soundbar using 3 Holder-Screws 2 as shown in the illustration.

Tighten the screws firmly.

ENG

15

INSTALLATION

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

5V 0.5A

SPK ADDWi-Fi SETUP

DC 24V

5V 0.5A

SPK ADDWi-Fi SETUP

DC 24V

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

3. Remove Holder-Support (2 EA) from the Soundbar as shown in the illustration.

4. Align the Soundbar’s centre with the centre of the base of the TV, and then carefully push it onto the stand

as far as it will go, as shown in the illustration. Be careful not to unbalance the TV.

● Do not place heavy items on the main unit. Do not step on the main unit.

16

INSTALLATION

INSTALLING THE SOUNDBAR AS A FREE-STANDING UNIT

1. Centre the Soundbar on the flat area in front of the TV.

ASSEMBLING THE CLAMP-WIRE

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

Clamp-Wire

Attach the clamp-wire to the unit as shown, and then run the cables through the clamp-wire to keep them neat.

ENG

17

CONNECTIONS

● Do not connect the power cord of this product or your TV to a wall outlet until all connections between

components are complete.

● Before moving or installing this product, be sure to turn off the power and disconnect the power cord.

CONNECTING THE SUBWOOFER

CONNECTING TO THE SUBWOOFER AUTOMATICALLY

The Subwoofer's linking ID is preset at the factory and the main unit and subwoofer should link (connect wirelessly)

automatically when the main unit and subwoofer are turned on.

• When the subwoofer is completely connected, the blue LED Link Indicator on the subwoofer stops blinking and

glows continuously.

CONNECTING TO THE SUBWOOFER MANUALLY

If the blue LED light does not stop blinking when the main unit and subwoofer are turned on, please set the ID by

following the steps below.

● Important: Before you begin, put the battery into the remote. See page 9 for instructions.

POWER

1. Plug the power cords of the main unit and subwoofer into an AC wall outlet.

2. Press the ID SET button on the back of the subwoofer with a small, pointed object for 5 seconds.

• The STANDBY indicator turns off and the LINK indicator (Blue LED) blinks quickly.

3. While the main unit is powered off (in STANDBY mode), press and hold the (Mute) on the remote control for

5 seconds.

4. The ID SET message appears on the Soundbar's display.

5. To finalise the link, turn the main unit’s power on while the subwoofer’s Blue LED blinks.

• The main unit and the subwoofer should now be linked (connected).

• The LINK indicator (Blue LED) on the subwoofer should be glowing continuously and not blinking.

• If the LINK indicator is not solid blue, the linking process has failed. Turn off the main unit and start again from

Step 2.

• You can enjoy better sound from the wireless subwoofer by selecting a Sound Effect.

(See page 9)

CONNECTIONS

18

CONNECTIONS

● Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

● If the main unit is powered off,the wireless subwoofer will in standy mode and the STNDBY LED on the

front will blink Red directly. (no blue LED).

● If you use a device that uses the same frequency (2.4GHz) as the Soundbar near the Soundbar,

interference may cause some sound interruption.

● The maximum transmission distance of the wireless signal between the main unit and subwoofer is about

10 meters, but may vary depending on your operating environment. If a steel-concrete or metallic wall is

between the main unit and the wireless subwoofer, the system may not operate at all, because the wireless

signal cannot penetrate metal.

● If the main unit doesn't make a wireless connection, follow steps 1-5 on the previous page to re-set the

connection between the main unit and wireless subwoofer.

● The wireless receiving antenna is built into the wireless subwoofer. Keep the unit away from water and

moisture.

● For optimal listening performance, make sure that the area around the wireless subwoofer location is clear

of any obstructions.

LED INDICATOR LAMP STATUS ON SUBWOOFER

LED Status Description Resolution

Red On

Standby (with the Soundbar main

unit turned off)

Check the power supply to the

Soundbar main unit

Connection failed

Connect again

(refer to the instructions on manual

connection in the user manual)

Blue

On

Successfully connected

(normal operation)

-

Blinking

Standby (with the Soundbar main

unit turned off)

Check the power supply to the

Soundbar main unit

Connection failed

Connect again

(refer to the instructions on manual

connection in the user manual)

Red and blue Blinking Malfunction Contact the service centre.

ENG

19

CONNECTIONS

CONNECTING TO A TV

● Important: Before you begin, put the battery into the remote. See page 9 for instructions.

TV SOUNDCONNECT

You can enjoy TV sound through your Soundbar when it is connected to a Samsung TV that supports the

TV SoundConnect function.

Connect

1. Turn on the TV and Soundbar.

2. Press the button on the main unit’s top panel or the SOURCE button on the remote control to select the TV

mode.

3. On the TV, a message asking whether to enable the TV SoundConnect function appears.

4. Select <Yes> using the TV's remote control to finish connecting the TV and Soundbar.

● If the TV SoundConnect linking process fails, navigate to SoundConnect in the TV's Sound menu, select

Add New Device, and set Add New Device to ON. Then, try again.

● Switching the Soundbar’s mode from TV to another mode automatically terminates TV SoundConnect.

●

To connect the Soundbar to another TV, the existing connection must be terminated.

● To terminate the existing connection, press and hold the

p

button on the remote for 5 seconds or switch

to another mode. To connect to the other TV, follow Steps 1 through 4 above.

● The TV SoundConnect (SoundShare) function is supported by some Samsung TVs released from 2012 on.

Check whether your TV supports the TV SoundConnect (SoundShare) function before you begin. (For

further information, refer to the TV’s user manual.).

● If your Samsung TV was released before 2014, check the SoundShare setting menu.

● If the distance between the TV and Soundbar exceeds 10 meters, the connection may not be stable or the

audio may stutter. If this occurs, relocate the TV or Soundbar so that they are within operational range, and

then re-establish the TV SoundConnect connection.

● TV SoundConnect Operational Ranges:

- Recommended pairing range: within 2 meters.

- Recommended operational range: within 10 meters.

● The Play/Pause, Next, and Prev buttons on the Soundbar or Soundbar's remote do not control the TV.

20

CONNECTIONS

CONNECTING TO A TV USING AN HDMI (DIGITAL) CABLE

SERVICE

SPK ADDWi-Fi SETUP

DC 24V

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

HDMI IN

HDMI OUT

(TV-ARC)

HDMI Cable

(not supplied)

1. Connect an HDMI cable (not supplied) from the HDMI OUT (TV-ARC) jack on the back of the product to the

HDMI IN jack on your TV.

2. Press the button on the top panel of the Soundbar or the SOURCE button on the remote control to select

the D.IN mode.

● HDMI is an interface that enables the digital transmission of video and audio data with just a single

connector.

● If the TV provides an ARC port, connect the HDMI cable to the HDMI IN (ARC) port.

● We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one whose

diameter is less than 14 mm.

● Anynet+ must be turned on.

● This function is not available if the HDMI cable does not support ARC.

CONNECTING TO A TV USING A DIGITAL OPTICAL CABLE

SERVICE

SPK ADDWi-Fi SETUP

DC 24V

AUX IN

LAN HDMI IN OPTICAL IN

HDMI OUT

(TV-ARC)

OPTICAL IN

OPTICAL OUT

Optical Cable

(not supplied)

1. Connect the OPTICAL IN (Audio) jack on the Soundbar to the OPTICAL OUT jack of the TV with a digital optical

cable.

2. Press the button on the top panel of the Soundbar or the SOURCE button on the remote control to select

the D.IN mode.

La page charge ...

Samsung HW-J7500R Manuel utilisateur

Samsung HW-J7500R Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents