Chamberlain B6765T Manuel utilisateur

User’s Guide

with specialty instructions

Belt Drive Garage Door Openers

B4545 B6765

FOR RESIDENTIAL USE ONLY

PRE-PROGRAMMED REMOTE

CONTROL INCLUDED

Register your garage door opener to receive

updates and offers from Chamberlain

1. Take a photo of the camera icon including the

points ( ).

2. Send it in by texting the photo to 71403 (US)

or visit chamberlain.registria.com (Global)

Smart Garage Opener

l Please read this manual and the enclosed safety materials

carefully!

l Fasten the manual near the garage door after installation.

l The door WILL NOT CLOSE unless the Protector System® is

connected and properly aligned.

l Periodic checks of the garage door opener are required to

ensure safe operation.

l The model number label is located on the left side panel or back

panel of your garage door opener.

l This garage door opener is compatible with myQ

®

and

Security+2.0® accessories.

l DO NOT install on a one-piece door if using devices or features

providing unattended close. Unattended devices and features are

to be used ONLY with sectional doors.

Contents

Preparation 2

myQ® App Control 3

Installation 4

Electrical and Wiring 10

Install the Protector System 10

Adjustments 13

Adjustments 14

Operation 15

Important Safety Instructions 15

Using your Garage Door Opener 15

Battery Backup 16

Smart Control Panel® 17

Motion Detecting Control Panel 18

Multi-Function Control Panel 19

Remote Control and Keyless Entry 20

HomeLink® 20

Erase the Memory 21

To Open the Door Manually 21

Maintenance 22

Troubleshooting 23

Warranty 25

Repair Parts 28

Rail Assembly Parts 28

Installation Parts 28

Model B4545 29

Model B6765 30

Go to chamberlain.com/belt-install to see installation videos.

www.chamberlain.com

2

Safety Symbol and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated,

maintained and tested in strict accordance with the instructions and warnings contained in this manual.

Mechanical

Electrical

When you see these Safety Symbols and Signal Words on

the following pages, they will alert you to the possibility of

serious injury or death if you do not comply with the

warnings that accompany them. The hazard may come

from something mechanical or from electric shock. Read

the warnings carefully.

When you see this Signal Word on the following pages, it

will alert you to the possibility of damage to your garage

door and/or the garage door opener if you do not comply

with the cautionary statements that accompany it. Read

them carefully.

WARNING: This product can expose you to chemicals including lead, which are known to the State of

California to cause cancer or birth defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov

Unattended Operation

The Timer-to-Close (TTC) feature, the myQ

®

App, and myQ

®

Garage Door and Gate Monitor are examples of

unattended close and are to be used ONLY with sectional doors. Any device or feature that allows the door to close

without being in the line of sight of the door is considered unattended close. The Timer-to-Close (TTC) feature, the

myQ

®

App, and any other myQ

®

devices are to be used ONLY with sectional doors.

The images throughout this manual are forreference only and yourproduct may look different.

When you see this symbol, refer to the Installation Manual.

Go to chamberlain.com/belt-install to see installation videos.

myQ

®

Serial Number

Write down the following information for future reference.

myQ Serial Number:

Product Serial Number:

Date of Purchase:

myQ serial number

Product serial number

Preparation

3

myQ

®

App Control

Connect With Your Smartphone

Youwill need:

l Wi-Fi enabled smartphone or tablet

l Broadband Internet connection

l Wi-Fi signal in the garage (2.4 GHz, 802.11b/g/n required)

l Password for your home network (router's main account, not guest network)

l myQ

®

serial number located on the garage door opener, see page 2

Check Wi-FiSignal Strength

Make sure your mobile device is connected to your Wi-Fi network. Hold your mobile device by the garage door

opener and check the Wi-Fi signal strength.

If you see:

Wi-Fi signal is strong. You’re all set!

Wi-Fi signal is weak.

The garage door opener will likely connect to your Wi-Fi network. If not, try one of the

options below.

No Wi-Fi signal. Try one of the following:

l Move your router closer to the garage door opener to minimize interference from

walls and other objects

l Buy a Wi-Fi range extender

Download the myQ

®

App to Set Up an Account andConnect

Open and close your door, get alerts and set schedules from anywhere. Connected smart garage door openers also

receive software updates to ensure the opener has the latest operational features.

1. Download the myQ

®

App.

2. Set up an account and connect.

For more information on connecting your garage door opener, visit support.chamberlaingroup.com.

An LED on the garage door

opener will indicate Wi-Fi

status. See table below

.

LED

Wi-FiStatus

LED Definition

Blue Off - Wi-Fi is not turned on.

Blinking - Garage door opener is in Wi-Fi learn mode.

Solid - Mobile device connected to the garage door opener.

Blue and Green Blinking - Attempting to connect to router.

Green Blinking - Attempting to connect to the Internet server.

Solid - Wi-Fi has been set up and garage door opener is connected to the internet.

NOTES:

myQ

®

App control and camera WILL NOT work if the garage door opener is operating on battery power.

To erase the Wi-Fi settings, see page 21.

4

Installation

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.

2. Install garage door opener ONLY on properly balanced and lubricated garage door. An improperly balanced

door may NOT reverse when required and could result in SEVERE INJURY or DEATH.

3. ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems

technician BEFORE installing opener.

4. Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing opener to avoid

entanglement.

5. Where possible, install the door opener 7 feet (2.13 m) or more above the floor.

6. Mount the emergency release within reach, but at least 6 feet (1.83 m) above the floor and avoiding contact

with vehicles to avoid accidental release.

7. NEVER connect garage door opener to power source until instructed to do so.

8. NEVER wear watches, rings or loose clothing while installing or servicing opener. They could be caught in

garage door or opener mechanisms.

9. Install wall-mounted garage door control:

l within sight of the garage door.

l out of reach of small children at a minimum height of 5feet (1.5m) above floors, landings, steps or any

other adjacent walking surface.

l away from ALL moving parts of the door.

10. Place entrapment warning label on wall next to garage door control in a prominent location.

11. Place emergency release/safety reverse test label in plain view on inside of garage door.

12. Upon completion of installation, test safety reversal system. Door MUST reverse on contact with a 1-1/2"

(3.8cm) high object (or a 2x4 laid flat) on the floor.

13. DO NOT install on a one-piece door if using devices or features providing unattended close. Unattended

devices and features are to be used ONLY with sectional doors.

Stop!

Follow the instructions in the Installation Manual unless otherwise noted.

5

Installation

If youare replacing a LiftMaster

®

, Chamberlain

®

, orCraftsman

®

garage door opener

youmay use the existing header bracket, see Installation step 1 in the Installation

Manual.

Installation 1- Install the Header Bracket

To prevent possible SERIOUS INJURY or DEATH:

l Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise

garage door might NOT reverse when required. DO NOT install header bracket over drywall.

l Concrete anchors MUST be used if mounting header bracket or 2x4 into masonry.

l NEVER try to loosen, move or adjust garage door, springs, cables, pulleys, brackets, or their hardware, ALL

of which are under EXTREME tension.

l ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An

unbalanced garage door might NOT reverse when required.

Determine Header Bracket Location

Installation procedures vary according to garage door types. Follow the instructions which apply to your door.

1. Close the door and mark the inside vertical centerline of the garage door.

2. Extend the line onto the header wall above the door. You can fasten the header bracket within 4 feet

(1.22m) of the left or right of the door center only if a torsion spring or center bearing plate is in the way; or

you can attach it to the ceiling (see page 6) when clearance is minimal. (It may be mounted on the wall

upside down if necessary, to gain approximately 1/2" (1 cm). If you need to install the header bracket on a

2x4 (on wall or ceiling), use lag screws (not provided) to securely fasten the 2x4 to structural supports as

shown .

3. Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header

wall above the high point:

l 2" (5 cm) above the high point for sectional door and one-piece door with track.

l 8" (20 cm) above the high point for one-piece door without track.

This height will provide travel clearance for the top edge of the door. NOTE: If this height is more than the space

available, use the maximum height possible, or refer to page 6 for ceiling installation.

Header Wall

Vertical Centerline of Garage Door

2x4

Structural

Supports

Level

(Optional)

Unﬁnished

Ceiling

2x4

OPTIONAL CEILING MOUNT

FOR HEADER BRACKET

Sectional door with curved track

Header Wall

Track

2" (5 cm)

Highest

Point of

Travel

Door

One-piece door with horizontal track

Header Wall

Track

2" (5 cm)

Highest

Point of

Travel

Door

One-piece door without track:

jamb

hardware

Header Wall

8" (20

cm)

Highest

Point of

Travel

Door

Jamb

Hardware

One-piece door without track:

pivot

hardware

Header Wall

8" (20

cm)

Highest

Point of

Travel

Door

Pivot

6

Installation

Attach the Header Bracket

You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions

which will work best for your particular requirements. Do not install the header bracket over drywall. If installing

into masonry, use concrete anchors (not provided).

II

Lag Screw 5/16"-9x1-5/8"

HARDWARE

OPTION A - Wall Installation

1. Center the bracket (I) on the vertical centerline with the bottom edge of the bracket on the horizontal line as

shown (with the arrow pointing toward the ceiling).

2. Mark the vertical set of bracket holes. Drill 3/16" pilot holes and fasten the bracket securely to a structural

support with the lag screws (II) provided.

OPTION B - CeilingInstallation

1. Extend the vertical centerline onto the ceiling as shown.

2. Center the bracket (I) on the vertical mark, no more than 6" (15 cm) from the wall. Make sure the arrow is

pointing away from the wall. The bracket can be mounted flush against the ceiling when clearance is

minimal.

3. Mark the side holes. Drill 3/16" pilot holes and fasten bracket securely to a structural support with the lag

screws (II)provided.

To continue, go to Installation step 2 in the Installation

Manual

WALL INSTALLATION

CEILING INSTALLATION

Optional Mounting

Holes

Header Wall

I

II

2x4

Structural

Support

Door

Spring

Garage Door

Highest Point

of Garage

Door Travel

Horizontal

Line

Header Wall

Ceiling Mounting

Holes

Finished Ceiling

Center of Door

6" (15 cm)

Maximum

Door Spring

Garage Door

Wall Mounting Holes

7/16"

7

Installation

If youare replacing a LiftMaster,Chamberlain,orCraftsman garage dooropeneryou

may use the existing doorbracket, see Installation step 10 in the Installation

Manual.

Installation 10 - Install the Door Bracket

Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of

door bracket. Contact the garage door manufacturer or installing dealer for opener reinforcement instructions or

reinforcement kit. Failure to reinforce the top section as required according to the door manufacturer may void the

door warranty.

SectionalDoors Only

1. Center the door bracket (O) on the door. Note correct UP placement, as stamped inside bracket.

2. Position the top edge of the bracket 2"-4" (5-10cm) below the top edge of the door, OR directly below any

structural support across the top of the door.

3. Mark, drill holes and install as follows, depending on your door’s construction.

Metal or light weight doors using a vertical angle iron brace in the door panel support and the door

bracket:

l Drill 3/16" fastening holes. Secure the door bracket with self-threading screws (OO). (Figure1)

l Alternately, use two 5/16"-18x2" bolts, lock washers and nuts (not provided). (Figure2)

Metal, insulated or light weight factory reinforced doors:

l Drill 3/16" fastening holes. Secure the door bracket with self-threading screws (OO). (Figure3)

Wood doors:

l Use top and bottom or side to side door bracket holes. Drill 5/16" holes through the door and secure

bracket with 5/16"-18x2" carriage bolts, lock washers and nuts (not provided). (Figure4)

NOTE: The self-threading screws (OO) are not intended for use on wood doors.

To continue, go to Installation step 11 in the

InstallationManual

FIGURE 1

FIGURE 3 FIGURE 4

FIGURE 2

Vertical

Reinforcement

Center of Door

UP

O

OO

Vertical Reinforcement

Horizontal Reinforcement

Center of Door

Hardware

(not provided)

UP

Center of Door

UP

Hardware

(not provided)

UP

Inside Edge of Door or

Reinforcement Board

HARDWARE

OO

Self-Threading Screw

1/4"-14x5/8"

OO

7/16"

Sectional Door

8

Installation

One-Piece Doors Only

1. Center the door bracket (O) on the top of the door, in line with the header bracket as shown.

2. Mark either the left and right, or the top and bottom holes.

Metal Doors:

l Drill 3/16" pilot holes and fasten the bracket with the self-threading screws (OO) provided.

Wood Doors:

l Drill 5/16" holes and use 5/16"-18x2" carriage bolts, lock washers and nuts (not provided) or 5/16"x1-1/2"

lag screws (not provided) depending on your installation needs.

NOTE: The door bracket may be installed on the top edge of the door if required for your installation. (Refer to the

dotted line optional placement drawing.)

For one-piece door installation continue to page 9

For a door with no exposed

framing, or for the optional

installation, use lag screws

5/16"x1-1/2" (not provided)

to fasten the door bracket.

Vertical

Centerline

of Garage

Door

Optional

Placement

of Door

Bracket

O

Header Bracket

Header Wall

2x4 Support

(Finished Ceiling)

O

Top of Door

(Inside Garage)

Top Edge of

Door

Optional

Placement

Optional

Placement

Top Edge

of Door

Top of Door

(Inside Garage)

Hardware

(not provided)

Hardware

(not provided)

Metal Door Wood Door

OO

7/16"

One-Piece Door

9

Installation

Forsectional door installations, see Installation step 11 inthe InstallationManual.

Installation 11 - Connect the Door Arm to the Trolley

One-Piece Door Only

IMPORTANT: The groove on the straight door arm MUST face away fromthe curved door arm.

1. Close the door. Disconnect the trolley by pulling the emergency release handle.

2. Fasten the straight door arm and the curved door arm together to the longest possible length (with a 2 or 3

hole overlap) using the bolts, nuts, and lock washers.

3. Attach the straight door arm to the door bracket using the clevis pin. Secure with the ring fastener.

4. Attach the curved door arm to the trolley using the clevis pin. Secure with the ring fastener.

5. Pull the emergency release handle toward the garage door opener until the trolley release arm is

horizontal.

To continue, go to Installation step 14 in the

InstallationManual

LL

Hex Bolt

NN

Nut

MM

Lock Washer

QQ

Clevis Pin 5/16"x1"

PP

Clevis Pin 5/16"x1-1/4"

KK

Ring Fastener

HARDWARE

One-Piece Door without Track

One-Piece Door with Track

KK

NN

MM

PP

LL

QQ

KK

NN

MM

LL

Straight Door Arm

(Groove facing out)

Curved Door Arm

1/2"

PP

QQ

L

M

10

Electrical and Wiring

Fortrack mounting,see Electrical and Wiringstep 6 in the Installation Manual.

Electrical and Wiring 6 - Install the Protector System

®

Be sure power is NOT connected to the garage door opener BEFORE installing the safety reversing sensor.

To prevent SERIOUS INJURY or DEATH from closing garage door:

l Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be

disabled.

l Install the safety reversing sensor so beam is NO HIGHER than 6" (15 cm) above garage floor.

IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSORS

The safety reversing sensors must be connected and aligned correctly before the garage door opener will

move in the down direction.

The safety reversing sensors can be attached to the door track, the wall, or the floor. The sensors should be no more

than 6" (15 cm) above the floor. If the door track will not support the sensor bracket a wall installation is

recommended. Choose one of the following installations.

Wall Installation

Position sensor brackets (P) on wall. Make sure safety reversing sensors are no more than 6" (15 cm) above the floor

and the light beam is unobstructed. Mark and drill 3/16" pilot holes. Attach with lag screws (not provided). NOTE: If

additional clearance is needed, wood blocks or extension brackets (not provided) can be used.

Floor Installation

Measure distance “X” to position both sensor brackets the same distance from the wall. Make sure the light beam is

unobstructed. Attach sensor brackets (P) to the floor using concrete anchors (not provided).

To continue, to Electrical and Wiring step 7 in the

InstallationManual

P

Lag Screws

(not provided)

Pre-Drill

3/

16"

No more than

6"

(15 cm)

Wood Block

(Not Provided)

Extension Bracket

(Not Provided)

Wall Installation

P

X

Concrete Anchors

(not provided)

No more than

6" (15 cm)

Floor Installation

11

Electrical and Wiring

Forinstallation with pre-wiring,see Electrical and Wiringstep 8 in the Installation

Manual.

Electrical and Wiring 8 - Wire the Safety Reversing Sensors

Without Pre-Wiring

1. Run the wire from both sensors to the garage door opener. Attach the wire to the wall and ceiling with

staples.

2. Strip 7/16" (11 mm) of insulation from each set of wires. Separate the wires. Twist the white wires

together. Twist the white/black wires together.

3. Insert the white wires into the white terminal on the garage door opener. Insert the white/black wires into

the grey terminal on the garage door opener. To insert or remove the wires fromthe terminal, push in the

tab with a screwdriver tip.

To continue, go to Electrical and Wiring 10 in the

InstallationManual

Staple

WHITE

GREY

RED

1

2

3

HARDWARE

Insulated Staple (Not Shown)

7/16" (11 mm)

12

Electrical and Wiring

Fortypicalwiring,see Electrical andWiring step 10 in the Installation Manual.

Electrical and Wiring 10 - Permanent Wiring

To prevent possible SERIOUS INJURY or DEATH from electrocution or fire:

l Be sure power is NOT connected to the opener, and disconnect power to circuit BEFORE removing cover to

establish permanent wiring connection.

l Garage door installation and wiring MUST be in compliance with ALL local electrical and building codes.

l NEVER use an extension cord, 2-wire adapter, or change plug in ANY way to make it fit outlet. Be sure the

opener is grounded.

If permanent wiring is required by your local code,

refer to the following procedure. To make a

permanent connection through the 7/8-inch hole in

the top of the motor unit (according to local code):

1. Remove the motor unit cover screws and set the

cover aside.

2. Remove the attached 3-prong cord.

3. Connect the black (line) wire to the screw on the

brass terminal; the white (neutral) wire to the screw

on the silver terminal; and the ground wire to the

green ground screw. The opener must be

grounded.

4. Reinstall the cover.

Ground Tab

Ground Wire

White Wire

Black Wire

Green Ground

Screw

To continue, go to Electrical and Wiring step 11 in the

InstallationManual

To align the safety reversing sensors, see Electrical andWiring step 13 in the

Installation Manual. If LEDs are still flashingornot glowing, follow the directions

below.

Electrical and Wiring 14 - Align the Safety Reversing Sensors

The door will not close if the sensors have not been installed and aligned correctly. The LEDs in both

sensors will glow steadily if they are aligned and wired correctly.

If the amber LED on the sending sensor is not glowing:

1. Make sure there is power to the garage door opener.

2. Make sure the sensor wire is not shorted/broken.

3. Make sure the sensor has been wired correctly: white wires to white terminal and white/black wires to

grey terminal.

RED

WHITE

GREY

3

2

1

If the green LEDonthe receiving sensor is not glowing:

1. Make sure the sensor wire is not shorted/broken.

2. Make sure the sensors are aligned.

1

2

To continue, go to Electrical and Wiring step 15 in the

InstallationManual

13

Adjustments

Forsectional door installations see Adjustments inthe Installation Manual.

Adjustments

One-Piece Doors Only

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY

INJURED or KILLED by a closing garage door.

l Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal

system.

l After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on

contact with 1-1/2" (3.8 cm) high object (or 2x4 laid flat) on floor.

To prevent damage to vehicles, be sure fully open door provides adequate clearance.

Your garage door opener is designed with electronic controls to make setup and adjustments easy. The adjustments

allow you to program where the door will stop in the open (UP) and close (DOWN) position. The electronic controls

sense the amount of force required to open and close the door. The force is adjusted automatically when you program

the travel.

NOTE: If anything interferes with the door’s upward travel it will stop. If anything interferes with the door’s downward

travel, it will reverse.

When setting the UP travel for a one-piece door ensure that the door does not slant backwards when fully open (UP).

If the door is slanted backwards this will cause unnecessary bucking and/or jerking when the door is opening or

closing.

To continue, go to Adjustments step 1 in the

InstallationManual

Open (UP)

Close (DOWN)

Correct

Incorrect

14

Camera

Set Up the Camera

1. Download the myQ

®

app and setup your account if you haven't already.

2. Follow the instructions in the app to setup and use the camera.

The camera powers up when it is opened and powers down when closed.

Camera

An LED on the garage

door opener will

indicate Wi-Fi status.

See table below

.

LED

Reset

Button

Camera Status

LED Definition

Flashing Blue Camera is attempting to connect to the mobile device.

Solid Blue Camera is connected to the mobile device.

Flashing Blue and Green Camera is attempting to connect to the router.

Flashing Green Camera is connected to the router and attempting to connect to myQ

®

server.

Solid Green Camera is connected and working normally.

Solid White Camera is booting.

Flashing Red Camera is overheating.

Flashing Purple Camera firmware is updating.

For more information on using the camera, visit support.chamberlaingroup.com.

NOTES:

myQ

®

App control and camera WILL NOT work if the garage door opener is operating on battery power.

To erase the Wi-Fi settings, see page 21.

15

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.

2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage

door control push buttons or remote controls.

3. ONLY activate garage door when it can be seen clearly, it is properly adjusted, and there are no obstructions

to door travel.

4. ALWAYS keep garage door in sight and away from people and objects until completely closed. NO ONE

SHOULD CROSS THE PATH OF THE MOVING DOOR.

5. NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY OPENED DOOR.

6. If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Use

caution when using this release with the door open. Weak or broken springs or unbalanced door could result in

an open door falling rapidly and/or unexpectedly and increasing the risk of SEVERE INJURY or DEATH.

7. NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.

8. NEVER use handle to pull garage door open or closed. If rope knot becomes untied, you could fall.

9. After ANY adjustments are made, the safety reversal system MUST be tested.

10. Safety reversal system MUST be tested every month. Garage door MUST reverse on contact with 1-1/2"

(3.8cm) high object (or a 2x4 laid flat) on the floor. Failure to adjust the garage door opener properly

increases the risk of SEVERE INJURY or DEATH.

11. ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED (see Installation Quickstart. An improperly

balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH.

12. ALL repairs to cables, spring assemblies and other hardware, ALL of which are under EXTREME tension,

MUST be made by a trained door systems technician.

13. ALWAYS disconnect electric and battery power to garage door opener BEFORE making ANY repairs or

removing covers.

14. This operator system is equipped with an unattended operation feature. The door could move

unexpectedly. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.

15. DO NOT install on a one-piece door if using devices or features providing unattended close. Unattended

devices and features are to be used ONLY with sectional doors.

16. SAVE THESE INSTRUCTIONS.

Using your Garage Door Opener

l The garage door opener can be activated with a wall-mounted door control, remote control, wireless keyless

entry, myQ

®

App or myQ

®

Garage Door Monitor. When the door is closed and the garage door opener is

activated the door will open. If the door senses an obstruction or is interrupted while opening the door will stop.

When the door is in any position other than closed and the garage door opener is activated the door will close. If

the garage door opener senses an obstruction while closing, the door will reverse. If the obstruction interrupts

the sensor beam the garage door opener lights will blink 10 times. If the door is fully open, and the safety

reversing sensors are not installed, or are misaligned, the door will not close from a remote control, TTC, or the

myQ

®

App. However, you can close the door by holding the button on the door control or the ENTER button on

the keyless entry until the door is fully closed.

l The garage door opener light will turn on when the opener is initially plugged in; power is restored after

interruption, or when the garage door opener is activated. The lights will turn off automatically after 4-1/2

minutes. The lights will turn on when someone enters through the open garage door and the safety reversing

sensor infrared beam is obstructed. Use an incandescent A19 light bulb (100W maximum) or for maximum

energy efficiency a 26W (100W equivalent) compact fluorescent light (CFL) bulb. NOTE: Do not use halogen,

short neck, or specialty light bulbs as these may overheat the end panel or light socket. Do not use LED bulbs as

they may reduce the range or performance of your remote controls.

Operation

16

Operation

Battery Backup

ModelB6765 Only

To reduce the risk of FIRE or INJURY to persons:

l Disconnect ALL electric and battery power BEFORE performing ANY service or maintenance.

l Use ONLY Chamberlain part # 041A6357-1 for replacement battery.

l DO NOT dispose of battery in fire. Battery may explode. Check with local codes for disposal instructions.

ALWAYS wear protective gloves and eye protection when changing the battery or working around the battery

compartment.

For battery installation, see Electrical and Wiring step 16 in

the InstallationManual

The battery backup allows access in and out of your garage, even when the power is out. The battery does not have to

be fully charged to operate the garage door opener. When the garage door opener is operating on battery power, it will

run slower and the battery status LED will glow solid orange, a beep will sound approximately every 2 seconds. The

following features are unavailable when operating on battery power:

l Garage Door Opener Lights

l Unattended close devices and features (e.g. myQ

®

App and Timer-to-Close)

Charge the Battery

The battery charges when the garage door opener is plugged into an electrical outlet and requires 24 hours to fully

charge. A fully charged battery supplies power to the garage door opener for 1 to 2 days of normal operation during an

electrical power outage. The battery will last approximately 1 to 2 years with normal usage. To obtain maximum

battery life and prevent damage, disconnect the battery when the garage door opener is unplugged for an extended

period of time, such as in a summer or winter home.

Battery status LED

GREEN LED: All systems are normal.

l A solid green LED light indicates the battery is fully charged.

l A flashing green LED indicates the battery is being charged.

ORANGE LED: The garage door opener has lost power and is in battery backup mode.

l A solid orange LED with beep, sounding approximately every 2 seconds, indicates the garage door opener

is operating on battery power.

l A flashing orange LED with beep, sounding every 30 seconds, indicates the battery is low.

RED LED: The garage door opener's 12V battery needs to be replaced.

l A solid red LED with beep, sounding every 30 seconds, indicates the 12V battery will no longer hold a

charge and needs to be replaced. Please call for replacement battery to allow your system to operate

during a power outage.

Battery

Status LED

Test the Battery

1. Unplug the garage door opener. The battery status LED will either glow solid orange indicating opener is

operating on battery power or will flash indicating low battery power. NOTE:Make sure the garage door

opener is unplugged.

2. Open and close the door using the remote control or door control. The garage door opener may run slower

if the battery is not fully charged. The battery will take 24 hours to fully charge.

3. Plug in the garage door opener. Verify the battery status LED is flashing green, indicating the battery is

charging.

17

Operation

Smart Control Panel

®

Push Bar

LIGHT Button

Motion Sensor

Screen

Navigation Buttons

SYNCHRONIZE THE DOOR CONTROL: To synchronize the door control

to the garage door opener, press the push bar until the garage door opener

activates (it may take up to 3 presses). Test the door control by pressing the

push bar; each press of the push bar will activate the garage door opener.

SCREEN: The screen displays the time, temperature, and current battery

charge (if applicable) until the menu button is pressed, and then it will display

the menu options. If there is a problem with the garage doors opener the

screen will display an error code, see page 23.

PUSH BAR: Press the push bar to open or close the door.

LOCK: Prevents remote controls from working, while still allowing

activation from the door control and keyless entry. (Factory setting is OFF.)

To turn the LOCK feature ON or OFF:

1. Select LOCK from the menu. When the LOCK feature is on, a

message displays on the screen.

LIGHT BUTTON: Turns the garage door opener lights on or off when

pressed. Lights stay on for 4-1/2 minutes (factory setting), and can be

changed by accessing the menu with the navigation buttons. The LIGHT

button will not control the lights when the door is in motion.

LIGHT SETTINGS:

To change the amount of time the lights stay on:

1. Select LIGHT SETTINGS from the menu.

2. Select LIGHT TIME.

3. Select the time interval.

To turn the entry light feature ON or Off (Factory default is On):

1. Select LIGHT SETTINGS from the menu.

2. Select AUTOMATIC LIGHTS.

3. Select ENTRY SENSOR.

MOTION SENSOR: Turns the garage door opener lights on when motion is

detected. Lights stay on for 4-1/2 minutes (factory setting), then turn off.

To turn the motion sensor ON or OFF:

1. Select LIGHT SETTINGS from the menu.

2. Select AUTOMATIC LIGHTS.

3. Select MOTION SENSOR.

TIMER-TO-CLOSE (TTC): DO NOT enable TTC if operating a one-piece

door. TTC is to be used ONLY with sectional doors. The TTC can be set to

close your garage door after a specified period of time (1, 5, or 10 minute

intervals). As the time to close the garage door opener occurs, the opener

beeps and the lights flash before closing the door. If an object blocks the door

while closing, the garage door opener will try to close the door again. If the

object is not removed after the second try, the garage door opener reverses

open, stop and WILL NOT close until the object is removed from the door’s

path. TTC WILL NOT work if the garage door opener is operating by battery

power or if the safety reversing sensors are misaligned. Adding a keyless

entry to control the opener is recommended to avoid an accidental lock out

when using this feature.

To turn TTC on or off or to set the TTC time interval:

1. Select TTC from the menu.

2. Select a time interval of 1, 5, 10 minutes or a custom setting up to

99 minutes. Once the TTC has been set and the door is open, a

message will display on the screen with the selected time interval.

To temporarily suspend the TTC feature select HOLD. Select REL to resume

normal TTC operation.

Other MenuOptions

CLOCK SETUP: Set the time; choose 12 or 24 hour clock and show/hide

clock.

TEMPERATURE: Display the temperature in Fahrenheit or Celsius and

show/hide the temperature.

LANGUAGE: Select English, Spanish or French.

CONTRAST ADJUST: Adjust the screen contrast.

PROGRAM: Any compatible remote control, wireless keyless entry, or

myQ

®

devices can be programmed to the garage door using the PROGRAM

option from the menu.

18

Operation

Motion Detecting Control Panel

ON (TTC)

OFF (TTC)

Command LED

Motion Sensor Switch

LIGHT Button

HOLD OPEN

But

ton(TTC)

Motion Sensor

1, 5, and 10 Minute

TTC LED

LEARN Button

LOCK Button

Push Bar

SYNCHRONIZE THE DOOR CONTROL: To synchronize the door control

to the garage door opener, press the push bar until the garage door opener

activates (it may take up to 3 presses). Test the door control by pressing the

push bar; each press of the push bar will activate the garage door opener.

PUSH BAR: Press the push bar to open or close the door.

LEARN BUTTON: Use to program compatible remote controls, wireless

keyless entries and myQ

®

devices to the garage door opener.

MOTION SENSOR: Turns the garage door opener lights on when motion is

detected. Lights stay on for 4-1/2 minutes (factory setting), then turn off. Set

the motion sensor switch ON or OFF to control this feature. The motion

sensor switch turns the motion sensor on or off.

Turn ON: Press and hold the LOCK button for 2 seconds. The command LED

will flash as long as the lock feature is on.

LOCK: Prevents remote controls from working, while still allowing

activation from the door control and keyless entry. (Factory setting is OFF.)

LIGHT BUTTON: Turns the garage door opener lights on or off when

pressed. Lights stay on for 4-1/2 minutes (factory setting). The LIGHT button

will not control the lights when the door is in motion.

To change the amount of time the lights stay on:

Press and hold the LOCK button (approximately 10 seconds) until the garage

door opener lights flash. The time interval is indicated by the number of times

the garage door opener lights flash:

l 1 flash is 1-1/2 minutes

l 2 flashes is 2-1/2 minutes

l 3 flashes is 3-1/2 minutes

l 4 flashes is 4-1/2 minutes

To cycle through the time intervals repeat the step above. If the push bar LED

is continuously blinking, the LOCK feature needs to be turned off.

To turn the light feature ON (Factory default is On):

1. Close the garage door.

2. Start with the garage door opener lights "ON".

3. Press and hold the LIGHT button (approximately 10 seconds) until

the garage door opener lights turn off, then on again.

To turn the light feature OFF:

1. Close the garage door.

2. Start with the garage door opener lights "OFF".

3. Press and hold the LIGHT button (approximately 10 seconds) until

the garage door opener lights turn off, then on again.

Turn OFF: Press and hold the LOCK button for 2 seconds. The command

LED will stop flashing and normal operation will resume.