Chamberlain 8365W-267 Manuel utilisateur

Marque: Chamberlain

Modèle: 8365W-267

Catégorie: Porte de garage

Taper: Manuel utilisateur

Ce manuel convient également à

PREMIUM Series Wi-Fi

Garage Door Opener

USER’S GUIDE

• Please read this guide and the enclosed safety materials carefully!

• The door WILL NOT CLOSE unless the Protector System

is connected and

properly aligned.

• Periodic checks of the garage door opener are required to ensure safe operation.

• This garage door opener is ONLY compatible with MyQ

and Security+ 2.0

accessories.

• DO NOT install on a one-piece door if using devices or features providing

unattended close. Unattended devices and features are to be used ONLY with

sectional doors.

• Attach warning labels to the location indicated on label.

FOR RESIDENTIAL USE ONLY

updates and offers from LiftMaster

Take a photo of the camera icon

including the points ( ).

Send it in by texting

the photo to 71403 (US)

or visit www.liftmaster.photo (Global)

8355W

8360W

8360WL

8365W

8365W-267

For the complete manual visit LiftMaster.com/Customer-Support

Contents

Power ........................................................... 3

Important Safety Instructions .............................3-4

Connect With Your Smartphone ..........................5-6

Test the Wi-Fi

Signal Strength ......................... 5

Connect Your Garage Door Opener to Your

Home Wi-Fi Network ...................................... 6

Programming .................................................. 7

Remote Control ............................................ 7

Wireless Keyless Entry ................................... 7

To Erase the Memory ..................................... 7

Operation................................................... 8-10

To Open the Door Manually .............................. 8

Door Control ................................................ 9

The Protector System

(Safety Reversing Sensors) .............................10

Adjustment ................................................11-13

Program the Travel .......................................12

Test the Safety Reversal System .......................13

Test the Protector System

.............................13

Maintenance ..................................................14

Troubleshooting ..............................................14

Repair Parts ..................................................15

Warranty ......................................................15

Automatic Garage Door Opener

Safety & Maintenance Guide ...........................16-17

Safety Symbol and Signal Word

Review

This garage door opener has been designed and tested

to offer safe service provided it is installed, operated,

maintained and tested in strict accordance with the

instructions and warnings contained in this manual.

When you see these Safety Symbols and Signal Words on

the following pages, they will alert you to the possibility

of serious injury or death if you do not comply with the

warnings that accompany them. The hazard may come

from something mechanical or from electric shock. Read

the warnings carefully.

Unattended Operation

The Timer-to-Close (TTC) feature, the MyQ

Smartphone

Control app, and MyQ

Garage Door and Gate Monitor are

examples of unattended close and are to be used ONLY

with sectional doors. Any device or feature that allows the

door to close without being in the line of sight of the door

is considered unattended close. The Timer-to-Close (TTC)

feature, the MyQ

Smartphone Control, and any other

MyQ

devices are to be used ONLY with sectional doors.

Mechanical

Electrical

When you see this Signal Word on the following pages, it

will alert you to the possibility of damage to your garage

door and/or the garage door opener if you do not comply

with the cautionary statements that accompany it. Read

them carefully.

Date of Purchase:

Product Serial Number

Write down the following information for future reference:

Product Serial Number:

MyQ

Serial Number:

WARNING: This product can expose you to

chemicals including lead, which are known to the

State of California to cause cancer or birth defects

or other reproductive harm. For more information

go to www.P65Warnings.ca.gov

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of severe injury or death:

WARNING

1. READ AND FOLLOW ALL WARNINGS AND

INSTRUCTIONS.

2. Install garage door opener ONLY on properly

balanced and lubricated garage door. An

improperly balanced door may NOT reverse when

required and could result in SEVERE INJURY or

DEATH.

3. ALL repairs to cables, spring assemblies and

other hardware MUST be made by a trained door

systems technician BEFORE installing opener.

4. Disable ALL locks and remove ALL ropes

connected to garage door BEFORE installing

opener to avoid entanglement.

5. Install garage door opener 7 feet (2.14 m) or more

above ﬂ oor.

6. Mount the emergency release within reach, but at

least 6 feet (1.83 m) above the ﬂ oor and avoiding

contact with vehicles to avoid accidental release.

7. NEVER connect garage door opener to power

source until instructed to do so.

8. NEVER wear watches, rings or loose clothing

while installing or servicing opener. They could be

caught in garage door or opener mechanisms.

9. Install wall-mounted garage door control:

• within sight of the garage door.

• out of reach of small children at a minimum

height of 5feet (1.5m) above ﬂ oors, landings,

steps or any other adjacent walking surface.

• away from ALL moving parts of the door.

10. Place entrapment warning label on wall next to

garage door control.

11. Place manual release/safety reverse test label in

plain view on inside of garage door.

12. Upon completion of installation, test safety reversal

system. Door MUST reverse on contact with a

1-1/2" (3.8 cm) high object (or a 2x4 laid ﬂ at) on

the ﬂ oor.

13. To avoid SERIOUS PERSONAL INJURY or DEATH

from electrocution, disconnect ALL electric and

battery power BEFORE performing ANY service or

maintenance.

14. DO NOT install on a one-piece door if using devices

or features providing unattended close. Unattended

devices and features are to be used ONLY with

sectional doors.

15.

SAVE THESE

INSTRUCTIONS.

Important Safety Instructions

Power

To prevent possible SERIOUS INJURY or DEATH from

electrocution or ﬁ re:

• Be sure power is NOT connected to the opener, and

disconnect power to circuit BEFORE removing cover to

establish permanent wiring connection.

• Garage door installation and wiring MUST be in

compliance with ALL local electrical and building codes.

• NEVER use an extension cord, 2-wire adapter, or change

plug in ANY way to make it ﬁ t outlet. Be sure the opener

is grounded.

To reduce the risk of electric shock, your garage door

opener has a grounding type plug with a third grounding

pin. This plug will only ﬁ t into a grounding type outlet.

If the plug doesn’t ﬁ t into your outlet, contact a qualiﬁ ed

electrician to install the proper outlet.

OPTION A TYPICAL WIRING

1. Plug in the garage door opener into a grounded outlet.

2. DO NOT run garage door opener at this time.

OPTION B PERMANENT WIRING

If permanent wiring is required by your local code, refer

to the following procedure.

To make a permanent

connection through the 7/8

inch hole in the top of the

motor unit (according to

local code):

1. Remove the motor unit

cover screws and set the

cover aside.

2. Remove the attached

3-prong cord.

3. Connect the black (line)

wire to the screw on the brass terminal; the white

(neutral) wire to the screw on the silver terminal; and

the ground wire to the green ground screw. The opener

must be grounded.

4. Reinstall the cover.

Ground Tab

Green

Ground

Screw

Ground

Wire

White Wire

PERMANENT WIRING

Black

Wire

Black

Wire

For the complete manual visit LiftMaster.com/Customer-Support

Important Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

WARNING

1. READ AND FOLLOW ALL WARNINGS AND

INSTRUCTIONS.

2. ALWAYS keep remote controls out of reach of

children. NEVER permit children to operate or play

with garage door control push buttons or remote

controls.

3. ONLY activate garage door when it can be seen

clearly, it is properly adjusted, and there are no

obstructions to door travel.

4. ALWAYS keep garage door in sight and away from

people and objects until completely closed. NO

ONE SHOULD CROSS THE PATH OF THE MOVING

DOOR.

5. NO ONE SHOULD GO UNDER A STOPPED,

PARTIALLY OPENED DOOR.

6. If possible, use emergency release handle to

disengage trolley ONLY when garage door is

CLOSED. Use caution when using this release

with the door open. Weak or broken springs or

unbalanced door could result in an open door

falling rapidly and/or unexpectedly and increasing

the risk of SEVERE INJURY or DEATH.

7. NEVER use emergency release handle unless

garage doorway is clear of persons and

obstructions.

8. NEVER use emergency release handle to pull

garage door open or closed. If rope knot becomes

untied, you could fall.

9. After ANY adjustments are made, the safety

reversal system MUST be tested.

10. Safety reversal system MUST be tested every

month. Garage door MUST reverse on contact with

1-1/2" high (3.8 cm) object (or a 2x4 laid ﬂ at) on

the ﬂ oor. Failure to adjust the garage door opener

properly increases the risk of SEVERE INJURY or

DEATH.

11. ALWAYS KEEP GARAGE DOOR PROPERLY

BALANCED. An improperly balanced door may NOT

reverse when required and could result in SEVERE

INJURY or DEATH.

12. ALL repairs to cables, spring assemblies and

other hardware, ALL of which are under EXTREME

tension, MUST be made by a trained door systems

technician.

13. ALWAYS disconnect electric power to garage door

opener BEFORE making ANY repairs or removing

covers.

14. This operator system is equipped with an

unattended operation feature. The door could move

unexpectedly. NO ONE SHOULD CROSS THE PATH

OF THE MOVING DOOR.

15. DO NOT install on a one-piece door if using devices

or features providing unattended close. Unattended

devices and features are to be used ONLY with

sectional doors.

16.

SAVE THESE

INSTRUCTIONS.

NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modiﬁ cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between users/bystanders and device.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules and Industry Canada ICES standard. These limits are designed

to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Test the Wi-Fi Signal Strength

Make sure your mobile device is connected to your Wi-Fi network. Hold your mobile device in the place where your

garage door opener is installed and check the Wi-Fi signal strength.

Before You Begin

You will need:

• Wi-Fi

enabled smartphone, tablet or laptop

• Broadband Internet Connection

• Wi-Fi signal in the garage (2.4 Ghz, 802.11b/g/n required)

• Password for your home network (router's main account, not guest network)

Check Signal Strength. If you see:

Wi-Fi signal is strong.

The garage door opener will connect to your

Wi-Fi network.

Wi-Fi signal is weak.

The garage door opener may connect to your Wi-Fi network. If

not, try one of the options below to improve the Wi-Fi signal.

No Wi-Fi signal.

The garage door opener will not be able to connect to your

Wi-Fi network. Try one of the options below to improve the

Wi-Fi signal:

• Move your router closer to the garage door opener to minimize

interference from walls and other objects

• Buy a Wi-Fi range extender

For compatible router speciﬁ cations and help, visit

WiFiHelp.LiftMaster.com.

Proceed to page 6.

Connect With Your Smartphone

For the complete manual visit LiftMaster.com/Customer-Support

1. Lift the push bar on the door control. Press and release the LEARN button. The garage door opener will

beep once and the command LED on the door control will blink to indicate Wi-Fi learn mode. You have

20 minutes to complete the connection process.

1. Lift the push bar on the door control. Press and release the LEARN

button. The garage door opener will beep once and the command

LED on the door control will blink to indicate Wi-Fi learn mode.

You have 20 minutes to complete the connection process.

Learn Button

Command LED

Multi-Function

Control Panel

882LMW

Learn Button

Command LED

Motion Detecting

Control Panel

886LMW

LED

An LED on the garage door

opener will indicate Wi-Fi

status.

See table below.

Actual product may differ

from image shown.

Connect With Your Smartphone

LED Deﬁ nition

Blue Off - Wi-Fi is not turned on.

Blinking - Garage door opener is in Wi-Fi learn mode.

Solid - Mobile device connected to the garage door opener.

Blue and Green Blinking - Attempting to connect to router.

Green Blinking - Attempting to connect to the Internet server.

Solid - Wi-Fi has been set up and garage door opener is connected to the internet.

Connect Your Garage Door Opener to Your Home Wi-Fi

Network

Get connected and control your garage door opener with the MyQ

app.

2. On your mobile device, go to Settings > Wi-Fi and select the

network with the “MyQ-” preﬁ x.

3. Launch the web browser on your smartphone or tablet. Enter

setup.myqdevice.com into the browser address bar. Follow the

on screen prompts to connect the garage door opener to your

Wi-Fi network. The MyQ serial number will display on screen.

Write the serial number in the space below.

4. Download the MyQ app from the App Store

or Google Play™

store. Sign up for your MyQ account and add the MyQ serial

number to your account.

To add a second Wi-Fi garage door opener, repeat steps 1-3. Add the

second MyQ serial number to your account in the MyQ app.

If you are unsuccessful adding your device, try an alternate web

browser or visit WiFiHelp.LiftMaster.com.

1. Press the LEARN button on the door

control to enter Programming Mode.

2. Press the LEARN button again, the LED

will ﬂ ash once.

3. Press the button on the remote control

that you wish to operate your garage

door.

Programming

Remote Control

Below are the steps to program a new or existing

remote control. Test remote control before

reprogramming.

1. Press and release the LEARN

Button on the garage door

opener.

2. Press and hold the button on the

remote control that you wish to

use. Release the button when

the garage door opener lights

blink or two clicks are heard.

If your vehicle is equipped with a Homelink

, you may

require an external adapter depending on the make,

model, and year of your vehicle.

Visit www.homelink.com for additional information.

Wireless Keyless Entry

Refer to the instructions provided with your

keyless entry OR go to LiftMaster.com to download

instructions.

To Erase the Memory

Erase ALL Remote Controls and Keyless Entries

Press and hold the LEARN button

until the LED goes out

(approximately 6 seconds).

All remote controls and

keyless entries are now erased.

Erase ALL Devices

(Including MyQ

enabled accessories)

1. Press and hold the LEARN button until the LED

goes out (approximately 6 seconds).

2. Immediately press and hold the LEARN button until

the LED goes out. All codes are now erased.

Erase the Wi-Fi Network from the

Garage Door Opener

Press and hold the adjustment

button until 3 beeps are heard

(approximately 6 seconds).

Erase a MyQ

Account

Go to myLiftMaster.com to delete your MyQ account.

LEARN

Button

Adjustment Button

For the complete manual visit LiftMaster.com/Customer-Support

Operation

To prevent possible SERIOUS INJURY or DEATH from a

falling garage door:

• If possible, use emergency release handle to

disengage trolley ONLY when garage door is

CLOSED. Weak or broken springs or unbalanced door

could result in an open door falling rapidly and/or

unexpectedly.

• NEVER use emergency release handle unless garage

doorway is clear of persons and obstructions.

• NEVER use emergency release handle to pull door

open or closed. If rope knot becomes untied, you

could fall.

To Open the Door Manually

NOTE: Disengage any door locks before proceeding.

1. The door should be fully

closed if possible.

2. Pull down on the emergency

release handle.

Lockout Feature

1. Pull the emergency release

handle down and back. The

door can then be raised and

lowered manually as often as

necessary.

2. To disengage the lockout

feature, pull the handle

straight down.

The trolley will reconnect on the next time the opener

is activated.

Disengage automatic garage

door lock before opening

door manually (if applicable).

Door Control

* The garage door opener must run through a complete cycle

before it will activate Wi-Fi

programming. For help related

to Wi-Fi, visit WiFiHelp.LiftMaster.com.

Push Bar

Service LED

LEARN Button

LOCK Button

Command LED

Light Button

Push Bar

MULTI-FUNCTION CONTROL PANEL 882LMW

MOTION DETECTING CONTROL PANEL 886LMW

Service LED

LEARN Button

LOCK Button

Command LED

Light Button

Motion Sensor

Automatic Garage Door Lock

(If applicable)

Lock terminals

Garage door opener models

featuring the Security Shield on

the cover are compatible with

the Automatic Garage Door Lock

(Model 841LM).

Battery Backup (If applicable)

The battery backup allows access in and out of your garage when

the power is out. When the garage door opener is operating on

battery power, the garage door opener will run slower and the

lights, Timer-to-Close, and remote close features (MyQ

App) are

disabled. In battery backup mode, the Automatic Garage Door

Lock will unlock when the garage door is opened, and will remain

disabled until power is restored. During a power outage the battery

supplies power for up to 24 hours of operation. For maximum

battery life and prevent damage, disconnect the battery when the

garage door opener is unplugged for an extended period of time.

Use an A19 incandescent

(100W maximum) or

compact ﬂ uorescent (26W,

100W equivalent) light bulb.

DO NOT use halogen, short

neck, or specialty light bulbs.

DO NOT use LED bulbs.

Battery Status LED

• Solid green LED -

Charged battery

• Flashing green LED -

Charging battery

• Solid orange LED with

beep - Operating on

battery power

• Flashing orange LED with

beep - Low battery

• Solid red LED with beep -

Replace battery

For the complete manual visit LiftMaster.com/Customer-Support

Operation

The Protector System

(Safety Reversing Sensors)

Be sure power is NOT connected to the garage door

opener BEFORE installing the safety reversing sensor.

To prevent SERIOUS INJURY or DEATH from closing

garage door:

• Correctly connect and align the safety reversing

sensor. This required safety device MUST NOT be

disabled.

• Install the safety reversing sensor so beam is NO

HIGHER than 6" (15 cm) above garage ﬂ oor.

The door will not close if the sensors have not been

installed and aligned correctly.

When the light beam is obstructed or misaligned while the

door is closing, the door will reverse and the garage door

opener lights will ﬂ ash ten times. If the door is already

open, it will not close.

The sensors can be aligned by loosening the wing nuts,

aligning the sensors, and tightening the wing nuts. Check

to make sure the LEDs in both sensors are glowing

steadily. The LEDs in both sensors will glow steadily if they

are aligned and wired correctly.

Safety Reversing Sensor

6" (15 cm) max. above ﬂoor

Safety Reversing Sensor

6" (15 cm) max. above ﬂoor

Green LED

RECEIVING SENSOR

Amber LED

SENDING SENSOR

(invisible light beam)

Wing

Nut

Wing

Nut

IF THE AMBER LED ON THE SENDING SENSOR IS NOT GLOWING:

1. Make sure there is power to the garage door opener.

2. Make sure the sensor wire is not shorted/broken.

3. Make sure the sensor has been wired correctly: White wires to white terminal and white/black wires to gray terminal.

IF THE GREEN LED ON THE RECEIVING SENSOR IS NOT GLOWING:

1. Make sure the sensor wire is not shorted/broken.

2. Make sure the senors are aligned.

Adjustment

Introduction

Without a properly installed safety reversal system,

persons (particularly small children) could be

SERIOUSLY INJURED or KILLED by a closing garage

door.

• Incorrect adjustment of garage door travel limits

will interfere with proper operation of safety reversal

system.

• After ANY adjustments are made, the safety reversal

system MUST be tested. Door MUST reverse on

contact with 1-1/2" (3.8 cm) high object (or 2x4 laid

ﬂat) on ﬂoor.

Your garage door opener is designed with electronic

controls to make setup and adjustments easy. The

adjustments allow you to program where the door will

stop in the open (UP) and close (DOWN) position. The

electronic controls sense the amount of force required to

open and close the door.

NOTE: If anything interferes with the door’s upward travel

it will stop. If anything interferes with the door’s downward

travel, it will reverse.

To watch a video, go to youtu.be/Fyl1-SxQxnE

To prevent damage to vehicles, be sure fully open door

provides adequate clearance.

Programming Buttons

The programming buttons are

located on the back panel of the

garage door opener and are used to

program the travel.

UP Button

Adjustment

Button

DOWN Button

For the complete manual visit LiftMaster.com/Customer-Support

Program the Travel

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY

INJURED or KILLED by a closing garage door.

• Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system.

• After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with

1-1/2" (3.8 cm) high object (or 2x4 laid ﬂ at) on ﬂ oor.

Adjustment

1.1 Press and hold the

Adjustment Button

until the UP Button

begins to ﬂ ash and/or

a beep is heard.

1.5 Once the door is in the

desired DOWN position

press and release the

Adjustment Button. The

garage door opener lights

will ﬂ ash twice and the UP

Button will begin to ﬂ ash.

1.2 Press and hold the UP Button until the door is

in the desired UP position.

NOTE: The UP and DOWN Buttons can be used to

move the door up and down as needed.

1.6 Press and release the UP Button. When the door

travels to the programmed UP position, the

DOWN Button will begin to ﬂ ash.

1.7 Press and release the DOWN Button. The door

will travel to the programmed DOWN position.

Programming is complete.

1.4 Press and hold the DOWN Button until the door is

in the desired DOWN position.

NOTE: The UP and DOWN Buttons can be used to

move the door up and down as needed.

* If the garage door opener lights are ﬂ ashing 5

times during the steps for Program the Travel, the

programming has timed out. If the garage door opener

lights are ﬂ ashing 10 times during the steps for Program

the Travel, the safety reversing sensors are misaligned

or obstructed. When the sensors are aligned and

unobstructed, cycle the door through a complete up

and down cycle using the remote control or the UP and

DOWN buttons. Programming is complete. If you are

unable to operate the door up and down, repeat the steps

for Program the Travel.

1.3 Once the door is in the

desired UP position press

and release the Adjustment

Button. The garage door

opener lights will ﬂ ash

twice and the DOWN

Button will begin to ﬂ ash.

2.1 With the door fully open, place a 1-1/2 inch

(3.8 cm) board (or a 2x4 laid ﬂ at) on the ﬂ oor,

centered under the garage door.

Test the Safety Reversal System

2.2 Press the remote control push button to close

the door. The door MUST reverse when it makes

contact with the board.

If the door stops but does not reverse:

1. Review the installation instructions provided to insure

all steps were followed; 2. Repeat Program the Travel (see

Adjustment Step 1); 3. Repeat the Safety Reversal test.

If the test continues to fail, call a trained door systems

technician.

Without a properly installed safety reversal system,

persons (particularly small children) could be

SERIOUSLY INJURED or KILLED by a closing garage

door.

• Safety reversal system MUST be tested every month.

• After ANY adjustments are made, the safety reversal

system MUST be tested. Door MUST reverse on

contact with 1-1/2" high (3.8 cm) object (or 2x4 laid

ﬂ at) on the ﬂ oor.

Test the Protector System

3.1 Open the door. Place an obstruction in the path of

the door.

The garage door opener will not close from a remote

control if the LED in either safety reversing sensor is off

(alerting you to the fact that the sensor is misaligned or

obstructed).

If the garage door opener closes the door when the safety

reversing sensor is obstructed (and the sensors are no

more than 6 inches [15 cm] above the ﬂ oor), call for a

trained door systems technician.

Without a properly installed safety reversing sensor,

persons (particularly small children) could be

SERIOUSLY INJURED or KILLED by a closing garage

door.

3.2 Press the remote control push button to close the

door. The door will not move more than an inch

(2.5 cm), and the garage door opener lights will

ﬂ ash 10 times.

Adjustment

For the complete manual visit LiftMaster.com/Customer-Support

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

To reduce risk of ﬁ re, explosion or chemical burn:

• Replace ONLY with 3V CR2032 coin batteries.

• DO NOT recharge, disassemble, heat above 212°F

(100°C) or incinerate.

The Remote Control Battery

Maintenance

EVERY MONTH

• Manually operate door. If it is unbalanced or binding,

call a trained door systems technician.

• Check to be sure door opens and closes fully. Adjust if

necessary, page 12.

• Test the safety reversal system. Adjust if necessary,

page 13.

EVERY YEAR

• Oil door rollers, bearings and hinges. The garage door

opener does not require additional lubrication. Do not

grease the door tracks.

• (If applicable) Test the battery backup and consider

replacing the battery to ensure the garage door opener

will operate during an electrical power outage.

Testing the Battery Backup:

1. Unplug the garage door opener from AC power. The

battery status LED will glow solid orange (opener

is operating on battery power) or will ﬂ ash (low

battery power).

2. Open and close the door using the remote control

or door control.

3. In battery backup mode, the Automatic Garage

Door Lock will unlock when the garage door is

opened, and will remain disabled until power is

restored.

4. Plug in the garage door opener. Verify the battery

status LED is ﬂ ashing green (battery is charging).

EVERY TWO TO THREE YEARS

• Use a rag to wipe away the existing grease from the

garage door opener rail. Reapply a small layer of white

lithium grease to the top and underside of the rail

surface where the trolley slides.

Replace with

only 3V CR2032

coin cell battery.

Pry open the case ﬁrst

in the middle (1), then

at each side (2 and 3)

with visor clip.

Troubleshooting

Below are basic troubleshooting tips, for additional help

and support videos visit LiftMaster.com/Customer-Support

or contact your installing dealer. For help related to Wi-Fi

visit WiFiHelp.LiftMaster.com.

My garage door opener will not close and the light bulbs

ﬂ ash:

Check to make sure the LEDs in both sensors are glowing

steadily. The LEDs in both sensors will glow steadily if they

are aligned and wired correctly. See page 10.

My vehicle’s Homelink

is not programming to my

garage door opener:

Depending on the make, model, and year of your vehicle an

external adapter may be required. Visit www.homelink.com

for additional information.

My garage door opener beeps:

The garage door opener can beep for several reasons:

• Garage door opener has been activated through a device

or feature such as Timer-to-Close, garage door monitor

or LiftMaster Internet Gateway.

• Operating on battery power or the battery needs to be

replaced.

My neighbor’s remote control opens my garage door:

Erase the memory from your garage door opener and

reprogram the remote control(s).

The garage door moves 6-8", stops or reverses:

• Manually open and close the garage door. Garage door

may be binding or there may be an obstruction. If the

door is binding, call a trained door systems technician.

• Possible travel module failure.

My remote control will not activate the garage door:

Verify the lock feature is not activated on the door control

or reprogram the remote control.

The wall-mounted door control will not function:

The wires for the door control are shorted or the door

control is faulty.

My garage door opener light(s) will not turn off when the

door is open:

The garage door opener is equipped with a feature that

turns the light on when the safety reversing sensors have

been obstructed or when the motion sensor on the door

control detects movement in the garage. This feature can

be disabled using the door control.

Garage door opener hums for 1-2 seconds with no

movement:

Manually open and close the garage door. Garage door

may be binding or there may be an obstruction. If the door

is binding, call a trained door systems technician.

Cannot connect garage door opener to home Wi-Fi

network:

Ensure the MyQ Serial number was entered correctly and

try again. The MyQ characters are between A-F and 0-9

only.

To troubleshoot the optional automatic garage door lock

model 841LM, see the instructions provided with it.

WARRANTY PERIOD

Parts Motor Accessories Belt Battery Backup*

8355W 1 year Lifetime 1 year Lifetime -

8360W

8360WL

1 year Lifetime 1 year - 1 year

8365W

8365W-267

1 year Lifetime 1 year - -

LIFTMASTER

LIMITED WARRANTY

LiftMaster (“Seller”) warrants to the ﬁ rst retail purchaser of this product, for the residence in which this product

is originally installed, that it is free from defects in materials and/or workmanship for a speciﬁ c period of time as

deﬁ ned below (the “Warranty Period”). The warranty period commences from the date of purchase.

The proper operation of this product is dependent on your compliance with the instructions regarding installation,

operation, and maintenance and testing. Failure to comply strictly with those instructions will void this limited

warranty in its entirety.

If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call

1-800-528-9131, toll free, before dismantling this product. You will be advised of disassembly and shipping

instructions when you call. Then send the product or component, pre-paid and insured, as directed to our service

center for warranty repair. Please include a brief description of the problem and a dated proof-of-purchase receipt

with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt

by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s

sole option) at no cost to you and returned pre- paid. Defective parts will be repaired or replaced with new or

factory-rebuilt parts at Seller’s sole option. [You are responsible for any costs incurred in removing and/or

reinstalling the product or any component].

ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE

APPLICABLE LIMITED WARRANTY PERIOD SET FORTH ABOVE FOR THE RELATED COMPONENT(S), AND NO

IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some States and Provinces do not allow

limitations on how long an implied warranty lasts, so the above limitation may not apply to you. THIS LIMITED

WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION,

OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE

AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR

CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT OF CONSUMABLE ITEMS

(E.G., BATTERIES IN REMOTE CONTROL TRANSMITTERS AND LIGHT BULBS), OR UNITS INSTALLED FOR NON-

RESIDENTIAL USE. THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE

GARAGE DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR

ROLLERS, DOOR ALIGNMENT OR HINGES. THIS LIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS

CAUSED BY INTERFERENCE. UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL,

INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE, OR INABILITY TO USE, THIS

PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT,

NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS

AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.

Some states and provinces do not allow the exclusion or limitation of consequential, incidental or special damages,

so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and

you may also have other rights, which vary from state to state and province to province.

* If applicable

Repair Parts

To see repair parts for your garage door opener, identify the model number on the end panel of the opener and visit

LiftMaster.com/Customer-Support to download or print the installation manual.

Warranty

For the complete manual visit LiftMaster.com/Customer-Support

Automatic Garage Door Opener

Safety & Maintenance Guide

Garage Door Openers are Not Toys

Discuss garage door and opener safety with your children. Explain the danger of

being trapped under the door.

Garage Door Opener Safety – An Automatic Decision

Stay away from a moving door.

Keep transmitters and remote controls out of reach

of children. Do not let children play with or use

transmitters or other remote control devices.

The wall-mounted push button should be out of reach of children,

at least 5 feet from the nearest standing surface and away from all

moving parts. Mount and use the button where you can clearly see

the closing garage door.

Keep the door in sight until it completely closes when using the

wall-mounted push button or transmitter.

A garage door is the largest moving object in the home. An improperly adjusted garage door and opener

can exert deadly force when the door closes – which could lead to entrapment of children or adults and

subsequent injury or death.

Proper installation, operation, maintenance, and testing of the garage door and automatic opener are necessary to

provide a safe, trouble-free system.

Careless operation or allowing children to play with or use garage door opener controls are also dangerous

situations that can lead to tragic results. A few simple precautions can protect your family and friends from

potential harm.

Please review the safety and maintenance tips in this guide carefully and keep it for reference. Check the operation

of your garage door and opener to ensure they function in a safe and trouble-free manner.

Be sure to read all Important Safety Information found in your garage door opener’s manual as it provides more

details and safety considerations than can be supplied with this guide.

Routine Maintenance Can Prevent Tragedies

• Starting with the door in the closed position, use the

manual disconnect on the opener to disconnect the door.

• Look for signs of wear or damage on hinges, rollers,

springs, and door panels.

• These parts may require periodic lubrication. Check the

owner’s manual for suggested maintenance.

• If any signs of damage are evident, contact a trained door

systems technician for assistance.

• Verify the photoeye height is no higher than 6" from the

garage ﬂ oor.

• Open and close the door manually using handles or

suitable gripping points.

• The door should move freely and without difﬁ culty.

• The door should balance and stay partially open 3–4

feet above the ﬂ oor.

• If you detect any signs of improper operation, contact a

trained door systems technician for assistance.

• Reconnect the opener to the door using the manual

disconnect and open the door.

• Place a 2x4 board ﬂ at in the path of the door (1) and try

to close it (2). The door should stop when it comes in

contact with the 2x4 and then reverse direction.

• Block the photoelectric sensor by waving an object in

front of the sensor and attempt to close the door. The

door should not close unless the wall-mounted push

button is manually held during operation.

• If the opener does not perform as described, contact a

trained door systems technician for assistance.

Make monthly inspection and testing of your garage door and opener system a part of your regular routine.

Review your owner’s manual for both the door and door opener. If you don’t have the owner’s manuals, contact

the manufacturer(s) and request a copy for your speciﬁ c model(s). Look for the opener model number on the

back of the power unit.

Test the opener safety features:

Test the door for proper operation:

Visually check the door

and installation:

WARNING – Springs are under high tension.

Only qualiﬁ ed individuals should adjust them.

114A5084

LiftMaster

300 Windsor Drive

Oak Br

ook, IL 60523

LiftMaster

.com

myLiftMaster.com

Wi-Fi

is a registered trademark of Wi-Fi Alliance.

App Store is a service mark of Apple Inc.

Google Play is a trademark of Google Inc.

Ouvre-porte de garage Wi-Fi

de série PREMIUM

GUIDE DE L’UTILISATEUR

• Veuillez lire attentivement ce guide de même que la documentation de sécurité

incluse.

• La porte NE SE FERMERA PAS si le Système Protector

n’est pas branché et

réglé correctement.

• Des vérifications périodiques de l’ouvre-porte de garage sont requises pour

garantir un fonctionnement sécuritaire du dispositif.

• Cet ouvre-porte de garage est compatible UNIQUEMENT avec les accessoires

MyQ

et Security+ 2.0

• NE PAS installer sur une porte rigide dans le cas de dispositifs ou fonctions

permettant la fermeture non surveillée. Les dispositifs et fonctions non surveillés

doivent être utilisés UNIQUEMENT avec des portes articulées.

• Apposer les étiquettes d’avertissement à l’endroit indiqué sur l’étiquette.

POUR RÉSIDENCES SEULEMENT

Enregistrez votre ouvre-porte de garage pour recevoir des mises à

jour et des offres de LiftMaster

Prenez une photo de l’icône d’appareil-photo, y

compris les points (

Envoyez la photo par message

textuel à 71403 (É.-U.)

ou allez à www.liftmaster.photo (mondial)

8355W

8360W

8360WL

8365W

8365W-267

Pour le manuel complet, visitez LiftMaster.com/Customer-Support

Matières

Fonctionnement non surveillé

La fonction de temporisation de fermeture (TTC),

l’application de commande MyQ

pour téléphone

intelligent, le dispositif de surveillance de porte de garage

et de barrière MyQ

sont des exemples de fermeture

non surveillée; ces fonctions doivent être utilisées

UNIQUEMENT avec des portes articulées. Tout dispositif

ou toute fonction qui permet la fermeture de la porte sans

visibilité directe de celle-ci constitue une fermeture non

surveillée. La fonction de temporisation de fermeture

(TTC), la commande MyQ

pour téléphone intelligent

et tous les autres dispositifs MyQ

doivent être utilisés

UNIQUEMENT avec des portes articulées.

ATTENTION

AVERTISSEMENT

Lorsque vous verrez ce mot de signalement sur les pages

suivantes, il vous avisera de la possibilité de dommages

à votre porte de garage ou ouvre-porte de garage, ou les

deux, si vous ne vous conformez pas aux énoncés de mise

en garde qui l’accompagnent. Lisez-les attentivement.

Revue des symboles de sécurité et

des mots de signalement

Cet ouvre-porte de garage a été conçu et mis à l’essai dans

le but d’offrir un service sûr à condition qu’il soit installé,

utilisé, entretenu et mis à l’essai en stricte conformité avec

les instructions et les avertissements contenus dans le

présent manuel.

Lorsque vous verrez ces symboles de sécurité et ces

mots de signalement sur les pages suivantes, ils vous

aviseront de la possibilité de blessures graves ou de mort

si vous ne vous conformez pas aux avertissements qui les

accompagnent. Le danger peut être de source mécanique

ou provenir d’un choc électrique. Lisez attentivement les

avertissements.

Mécanique

Électrique

ATTENTION

AVERTISSEMENT

ATTENTION

AVERTISSEMENT

Date d’achat :

Numéro de série

Veuillez noter les renseignements suivants pour référence

ultérieure :

Numéro de série :

Numéro de série MyQ

Numéro de série :

Alimentation ................................................... 3

Importantes Consignes de Sécurité ......................3-4

Connectez-vous votre téléphone intelligent ............5-6

Tester la Puissance du Signal Wi-Fi

.................. 5

Connecter l’ouvre-porte de garage au réseau

Wi-Fi de votre domicile .................................. 6

Programmation................................................ 7

Télécommande ............................................ 7

Émetteur à code ........................................... 7

Pour effacer la mémoire ................................. 7

Fonctionnement ........................................... 8-10

Ouverture manuelle de la porte ......................... 8

Commande de porte ...................................... 9

Protector System

(Capteur d’inversion de sécurité) ......................10

Réglage ...................................................11-13

Programmation des courses ............................12

Essai du système d’inversion de sécurité ............13

Essai du Protector System

.............................13

Entretien.......................................................14

Dépannage ....................................................14

Pièces de Rechange .........................................15

Garantie .......................................................15

Guide de sécurité et d’entretien de

l’ouvre-porte de garage automatique .................16-17

AVERTISSEMENT : Ce produit peut vous exposer

à des produits chimiques comme le plomb,

reconnu par l’État de la Californie comme cause

de cancers, d’anomalies congénitales et d’autres

problèmes liés à la reproduction. Pour plus

d’informations, visitez www.P65Warnings.ca.gov

La page charge ...

Chamberlain 8365W-267 Manuel utilisateur

Marque: Chamberlain

Modèle: 8365W-267

Catégorie: Porte de garage

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Chamberlain 8365W-267 User manual

Chamberlain 8365W-267 Manuel utilisateur

Ce manuel convient également à

Chamberlain 8365W-267 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents