Zephyr AK8100ASBF Manuel utilisateur

Use, Care, and Installation Guide

www.zephyronline.com

Model number:

Serial Number:

Date of Purchase:

Sales Dealer:

APR19.0901 © Zephyr Ventilation LLC.

Twister

AK8000BS

AK8000AS-ES

Tornado I

AK8100AS-BF

READ AND SAVE THESE INSTRUCTIONS

AK8000BS

AK8100AS-BF

AK8000AS-ES

www.zephyronline.com

1

SAFETY NOTICE ................................................................. 2-3

LIST OF MATERIALS ....................................................... 4

INSTALLATION

Ducting Calculation Sheet ....................................... 5

Mounting Height & Clearance ................................ 6

Ducting Options ........................................................... 7

Specications ............................................................... 8

Electrical ......................................................................... 9

Installing the Power Pack ........................................ 10

FEATURES & CONTROLS

Slide Controls ............................................................... 11

MAINTENANCE

Cleaning and Installing Filters ............................... 12

AK8000BS Recirculating Kit ................................... 13

Lights ................................................................................ 14

TROUBLESHOOTING................................................................ 15

WIRING DIAGRAMS ................................................................... 16

LIST OF PARTS AND ACCESSORIES .............................. 17

WARRANTY .................................................................................... 18-19

PRODUCT REGISTRATION .................................................... 20

Table of Contents

Important Safety Notice

READ AND SAVE THESE INSTRUCTIONS

2

www.zephyronline.com

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.

WARNING

TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.

b. Beforeservicingorcleaningunit,switchpoweroatservicepanelandlockpaneltopreventpowerfrombeingswitchedonaccidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service

panel.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning

agents or detergents. Suitable for use in household cooking area.

WARNING

TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:

a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly

on low or medium settings.

b. AlwaysturnhoodONwhencookingathighheatorwhenamingfood

c. Cleanventilatingfansfrequently.Greaseshouldnotbeallowedtoaccumulateonfanorlter.

d. Use proper pan size. Always use cookware appropriate for the size of the surface element.

e. Keepfan,ltersandgreaseladensurfacesclean.

f. Use high setting on hood only when necessary.

g. Don’t leave hood unattended when cooking.

h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:

a. SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnotheburner.BECAREFULTOPREVENTBURNS.

Iftheamesdonotgooutimmediately,EVACUATEANDCALLTHEFIREDEPARTMENT.

b. NEVER PICK UP A FLAMING PAN – You may be burned.

c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Installationworkandelectricalwiringmustbedonebyqualiedperson(s)inaccordancewithallapplicablecodesandstandards.

Includingre-ratedconstruction.

b. Sucientairisneededforpowercombustionandexhaustingofgasesthroughtheue(chimney)offuelburningequipmenttoprevent

back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National

FireProtectionAssociation(NFPA)andtheAmericanSocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE)and

the local code authorities.

c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

d. Ducted fans must always vent to the outdoors.

e. NEVER place a switch where it can be reached from a tub or shower.

f. Makesurethepowerisobeforeinstalling,wiringormaintenancing.

Important Safety Notice

3

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

Toreduceriskofreandtoproperlyexhaustairoutside-Donotventexhaustairintospaceswithinwalls,ceilings,

attics, crawl spaces or garages.

OPERATION

Alwaysleavesafetygrillesandltersinplace.Withoutthesecomponents,operatingblowerscouldcatchontohair,ngers

and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to

negligence and the warranty of the unit automatically expires due to improper maintenance.

*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility:

- Tocontactaqualiedelectricalinstaller.

- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and

all local codes and ordinances.

Ifcodespermitandaseparategroundwireisused,itisrecommendedthataqualiedelectriciandeterminethatthe

ground path is adequate.

Do not ground to a gas pipe.

Checkwithaqualiedelectricianifyouarenotsuretherangehoodisproperlygrounded.

Do not have a fuse in the neutral or ground circuit.

*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit

protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to

Electrical Diagram on product.

AK8000BS(400cfm)-315W,2.7Amps

AK8000AS-ES(290cfm)-96W,1.2Amps

AK8100AS-BF(600cfm)-377W,3.3Amps

Acablelockingconnector(notsupplied)mightalsoberequiredbylocalcodes.Checkwithlocalrequirements,purchase

and install appropriate connector if necessary.

Cancer and Reproductive Harm - www.P65Warnings.ca.gov

WARNING:

Prop. 65 Warning for California Residents

List of Materials

4

www.zephyronline.com

MODELS: AK8000BS, AK8000AS-ES, AK8100AS-BF

PARTS SUPPLIED

1 - Power Pack

1-Aluminummeshlter(AK8000BS&AK8000AS-ES)

1-HybridBaelter(AK8100AS-BF)

2-Halogenlightbulbs(AK8000BS&AK8100AS-BF)

2-Fluorescentlightbulbs(AK8000AS-ES)

1-Singleinternalblower(pre-installed)

1 - Hardware package

HARDWARE PACKAGE CONTENTS

PARTS NOT SUPPLIED

- Ducting, conduit and all installation tools

- Cable connector (if required by local codes)

- Optional stainless steel liner (AK08xxAS)

-OptionalRecirculatingKitforAK8000BS(ZRC-0100)

Suction Cup (1)

AK8000BS, AK8100AS-BF

Wire Caps (3)

M4 x 1” (4)

M4 x 1-1/2” (4)

5

Installation – Ducting Calculation Sheet

Duct pieces

To tal

Equivalent number

length x used =

3- 1/ 4” x 10”

Rect.,

straight

1 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

90

0

elbow

20 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

90

0

15 Ft.

x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

45

0

9 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

straight

1 Ft. x ( ) =

Ft.

Subtotal column 1 =

Duct pieces

To tal

Equivalent number

length x used =

6”, 7”, 8”, 10”

Round, wall

cap with

damper

30 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round

roof cap

30 Ft. x ( ) =

Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length

should not exceed 100 equivalent feet.

6” round to

3- 1/ 4” x 10”

rect.

transition

1 Ft. x ( ) =

Ft.

6” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

16 Ft. x ( ) =

Ft.

7” round to

3 1/ 4” x 10”

rect.

transition

8 Ft. x ( ) =

Ft.

7” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

23 Ft. x ( ) =

Ft.

elbow

7” to 6” or

8” to 7” Round

tapered

reducer

25 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

elbow

15 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 45

0

elbow

9 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

flat elbow

24 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) =

Ft.

Ft. x ( ) =

Ft.

15

6”, 7“, 8”

Round

in-line

damper

Installation – Mounting Height & Clearance

6

www.zephyronline.com

DUCTING

A minimum of 6” round or 3-1/4” x 10” rectangular

ductmustbeusedtomaintainmaximumairow

eciency.

Always use rigid type metal ducts only. Flexible

ductscouldrestrictairowbyupto50%.

Alsousecalculation(onpage5)tocomputetotal

available duct run when using elbows, transitions

and caps.

ALWAYS, when possible, reduce the number or

transitions and turns. If long duct run is required,

increase duct size.

If turns or transitions are required; install as far

away from hood duct output and as far apart,

between the two as possible.

Minimum mount height between range top to hood

bottom should be no less than 24”.

For optimal performance, the recommended

maximum mounting height should be no higher

than 36”.

It is important to install the hood at the proper

mounting height. Hoods mounted too low could

resultinheatdamageandrehazard;whilehoods

mounted too high will be hard to reach and will

loseitsperformanceandeciency.

If available, also refer range manufacturer’s height

clearance requirements and recommended hood

mounting height above range.

Vertical Ducting:

6” round minimum

Horizontal Ducting:

N/A

DAMAGE-SHIPMENT / INSTALLATION:

• Please fully inspect unit for damage before

installation.

• If the unit is damaged in shipment, return the

unit to the store in which it was bought for

repair or replacement.

• If the unit is damaged by the customer, repair

or replacement is the responsibility of the

customer.

• Iftheunitisdamagedbytheinstaller(ifother

thanthecustomer),repairofreplacementmust

be made by arrangement between customer

and installer.

Min 24" - Max 36"

36"

7

WARNING FIRE HAZARD

NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.

All exhaust must be ducted to the outside.

Use metal ductwork only.

FastenallconnectionswithsheetmetalscrewsandtapealljointswithcertiedSilverTapeorDuctTape.

Some Ducting Options

Installation – Ducting Options

side wall cap

w/ gravity damper

side wall cap

w/ gravity dampe

r

Soffit or crawl space

Roof Pitch w/

Flashing & Cap

8

www.zephyronline.com

Installation – Specications

top

front

bottom side

4-1/8”

5-3/8”

3-3/4”

10-5/8”

5-7/8”

1-1/16”

10-1/2”

11-13/16”

26-9/16”

27-9/16”

25-3/4”

9-3/8”

8-11/16”

11-3/16”

10-5/16”

1-5/16”

15”

18-15/16”

10-5/16”

1-1/8”

C/L

9

ELECTRICAL

WARNING

All Electrical work must be performed by qualied electrician or person with similar technical know

how and background.

For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use

extension cord or adapter plug with this appliance.

Follow national electrical codes or prevailing local codes and ordinances.

Electrical Supply:

This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded

branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire w/

ground. Please also refer Electrical Diagram labeled on product.

Cable Lock:

Acablelockingconnector(notsupplied)mightalsoberequiredbylocalcodes.Checkwithlocalrequirements

and codes, purchase and install appropriate connector if necessary.

Installation – Electrical

Cable Lock

10

www.zephyronline.com

Installation – Installing the Power Pack

1. Install optional AK08xxAS Stainless Steel Liner. Review

manual included with liner for more details.

2. If no liner is used cut out an opening in the bottom of the

cabinet by following the dimensions in FIG 1.

3. Lift Power Pack into opening and ensure locking clip has

lockedintoposition.(lockingclipislocatedonleftsideof

Power Pack. FIG 2

4.Fasten(2)M4screwsintoeachlongsideofPowerPack.

If a liner is used the screws will go through the Power Pack

mounting holes, then the liner and into the wood base.

note: Wood blocking may need to be added to cabinet

base if additional support is needed. see FIG 3 and FIG 4

5. Install duct work and seal with duct tape.

7. Install electrical.

8. Remove all packing materials before using Power

Pack. Switch power on and check for leaks around duct

tape.

9.Installlter.

The ducting from this fan to the outside of the building has a strong

eectontheairow,noiseandenergyuseofthefan.Usetheshortest,

straightest duct routing possible for best performance, and avoid

installing the fan with smaller ducts than recommended. Insulation

around the ducts can reduce energy loss and inhibit mold growth. Fans

installedwithexistingductsmaynotachievetheirratedairow.

CAUTION: At least two installers ar

e

required

due to the weight and size of

the

hood.

!

Ductwork

wood base

2” minimum

secure (2) M4 screws to mounting

holes on each long side of Power Pack

metal or other non

combustible material

D

uctwor

k

wood base

woo

d

b

as

e

2

” minimum

FIG 1

FIG 2

FIG 3

FIG 4

locking clip

mounting holes

controls

front view

right side view

Ductwork

cabinet bottom cut-out size

26

7/8

”

10

5/8

”

Power Pack

Stainless Steel Liner

C/L

11

17

0 I II III

Blower On/Off Speed Selection

1

Lights Bright/Dim/Off

2

0 I II

Features & Controls – Slide Controls

BLOWER ON/OFF/SPEED SELECTION

0iso,Iislowspeed,IIismediumspeedandIIIishighspeed.

LIGHTS BRIGHT/DIM/OFF

0iso,Iisdim,andIIisbright.

1

2

BLOWER ON/OFF/SPEED SELECTION

0iso,Iislowspeed,IIismediumspeedandIIIishighspeed.

LIGHTS ON/OFF

0isoandIison.

1

2

17

0 I II III

Blower On/Off Speed Selection

1

Lights On/Off

2

0 I

AK8000BS & AK8100AS-BF

AK8000AS-ES

12

www.zephyronline.com

SURFACE MAINTENANCE:

Do not use corrosive detergents, abrasive detergents or oven cleaners.

Do not use any product containing chlorine bleach or any product containing chloride.

Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface.

Cleaning Stainless Steel

Cleanperiodicallywithwarmsoapywaterandcleancottonclothormicrobercloth.Alwaysrubinthedirectionofthe

stainless steel grain. To remove heavier grease build up use a liquid degreaser detergent.

Aftercleaninguseanon-abrasivestainlesssteelpolish/cleaners,topolishandbuoutthestainlesslusterandgrain.

Alwaysscrublightly,withcleancottonclothormicroberclothandbuinthedirectionofthestainlesssteelgrain.

Cleaning Filters

Thealuminummeshltersinstalledbythefactoryareintendedtolteroutresidueandgreasefromcooking.Theyneed

not be replaced on a regular basis but are required to be kept clean.

Removeandcleanbyhandorindishwasherusinganon-phosphatedetergent.Discolorationoftheltermayoccur

ifusingphosphatedetergents,orasaresultoflocalwaterconditions-butthiswillnotaectlterperformance.This

discoloration is not covered by the warranty. Spray degreasing detergent and leave to soak if heavily soiled.

Drylterandre-installbeforeusinghood.

Installing Filter, FIG 5:

1.PlacebackoflterintochannelonleftsideofPowerPack.

2. PushlterhandleintowardsleftsideofPowerPack.

3.Pivotlterupandlockintoplace.

Hood Model: Part No. Qty. to Order

AK8000BS 50200022 1

AK8000AS-ES 50200022 1

AK8100AS-BF 50210030 1

3

FIG 5

FIG 6

2

1

2

3

Maintenance – Cleaning and Installing Filters

13

DUCTLESS RECIRCULATING (AK8000BS ONLY):

Ductless recirculating is intended for applications where an exhaust duct work is not possible to be installed.

When converted, the power pack functions in air “purifying” mode rather than exhausting the air. Fumes and

exhaustfromcookingisdrawnandlteredbyacharcoallter.Theairisthenpuriedandrecirculatedback

into the kitchen.

We recommend to always exhaust air outside of the home by employing existing or installing new duct work, if

possible.Thepowerpackismosteectiveandecientasanexhaustunit.Onlywhentheexhaustoptionis

not possible should you use the power pack in recirculating mode.

Whenconvertedtorecirculatingmode,acharcoallterisrequiredtobeinstalledontopofthestandard

aluminummeshlterandareturnairventisneededtodirectairbackintothekitchen.Thestandard

aluminummeshlterisintendedtocaptureresiduefromcookingandtheoptionalcharcoallterhelpsto

purify fumes exhausted from cooking in recirculating mode.

Purchase recirculating kit as follows, for AK8000BS ONLY:

Hood Model: Part No. Qty. to Order

AK8000BS ZRC-0100 1

Charcoalltersmustbereplacedapproximatelyevery3monthsbasedoanaverageusageof1houraday.

Orderreplacementcharcoalltersasfollows:

Hood Model: Part No. Qty. to Order

AK8000BS Z0F-C002 1

For detailed installation instructions please refer to manual included with recirculating kit.

Installcharcoalfilter(plasticsideup)into

filter bracket. Insert tab cut-out side D of

charcoal filter into bracket first. Lock

charcoal filter into place by pushing down

on side E with locking tabs.

D

E

Maintenance – AK8000BS Recirculating Kit

14

www.zephyronline.com

REPLACING LIGHT BULBS

CAUTION: Light bulb becomes extremely hot when turned on.

DO NOT touch bulb until switched o and cooled. Touching hot bulbs could cause serious burns.

Makesureallpoweristurnedoandbulbsarenothot.

Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees, stops and

falls out.

Ifbulbsarediculttoturnduetoprolongeduse,rmlyattachaglasssuctioncupapproximatelythe

diameter of the bulb or use a rubber/latex glove and turn counter clockwise.

Replacement bulbs are available at http://store.zephyronline.com

For Zephyr part numbers please turn to page 17 of the manual.

Maintenance – Lights

3

FIG 5

FIG 6

2

1

2

3

AK8000BS & AK8100AS

AK8000AS-ES

Troubleshooting

15

TROUBLESHOOTING PROCEDURES FOR TWISTER AND TORNADO 1

Issue Cause What to do

After installation,

the unit doesn’t

work.

1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s

power is ON.

2. The power line and the cable locking connector

is not connecting properly.

2. Check the power connection with the unit is

connected properly.

Light works,

but motor is not

turning.

1. The motor plug is disconnected. 1. Connect the motor plug.

2. The motor is defective, possible seized. 2. Change the motor.

3. The thermally protected system detects if the

motor is too hot to operate and shuts the motor

down.

3. The motor will function properly after the

thermally protected system cool down.

4. Damaged capacitor. 4. Change the capacitor.

The unit is

vibrating.

1. The blower is not secure in place. 1. Tighten the blower in place.

2. Damaged blower wheel. 2. Change the blower.

3. The hood is not secured in place. 3. Check the installation of the hood.

The motor is

working, but the

lights are not.

1. Defective light bulb. 1. Change the light bulb.

2. The light bulb is loose. 2. Tighten the light bulb.

The hood is

not venting out

properly.

1. The hood might be hanging to high from the

cook top.

1. Adjust the distance between the cook top and

the bottom of the hood within 24” to 36” range.

2. The wind from the opened windows or opened

doorsinthesurroundingareaareaectingthe

ventilation of the hood.

2. Close all the windows and doors to eliminate

theoutsidewindow.

3. Blocking in the duct opening or duct work. 3. Remove all the blocking from the duct work or

duct opening.

4. The direction of duct opening is against the wind. 4. Adjust the duct opening direction.

5. Using the wrong size of ducting. 5. Change the ducting to at least 6” or higher.

Metallteris

vibrating.

1. Metallterisloose. 1. Changethemetallter.

2. Spring clip is broken. 2. Change the spring clip.

16

www.zephyronline.com

Wiring Diagrams

Model: AK8000AS-ES

Voltage: 120V 60Hz 1.2A

Total: 96W

Lamp: Max.13Wx2

Fan: 70W

THERMALLY PROTECTED

Power Consumption

BLUE

BROWN

GREY

YELLOW

RED

WHITE

BLACK

GREEN

BODY

CIRCUIT DIAGRAM

B/W

Model: AK8100AS-BF

Voltage 120V 60Hz 3.3A

Total: 377W

Lamp: Max.35Wx2

Fan: 307W

THERMALLY PROTECTED

DATE:

Power consumption

17

DESCRIPTION PART #

Replacement Parts

HalogenLightBulb,GU-10,35W(AK8000BS,AK8100AS-BF)  Z0B0023  

FluorescentLightBulb,13W(AK8000AS-ES)   Z0B0036

AluminumMeshFilter(AK8000BS,AK8000AS-ES)   50200022

HybridBaeFilter(AK8100AS-BF)    50210030

Optional Accessories

Liner,30” AK0800AS

Liner,36” AK0836AS

RecirculatingKit(AK8000BSONLY) ZRC-0100

To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368

List of Parts and Accessories

18

www.zephyronline.com

Warranty AK8000BS & AK8100AS-BF

1-888-880-8368

STAPLE YOUR RECEIPT HERE

TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call:

Zephyr Ventilation, LLC (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to

herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials

or workmanship as follows:

Ten Year Limited Warranty for Parts: For ten years from the date of your original purchase of the Products, we will

provide, free of charge, Products or parts (including LED light bulbs, if applicable) to replace those that failed due to

manufacturing defects. We may choose, in our sole discretion, to repair or replace parts before we elect to replace the

Products.

One Year Limited Warranty for Labor: For one year from the date of your original purchase of the Products, we will

provide, free of charge, the labor cost associated with repairing the Products or parts to replace those that failed due to

manufacturing defects. After the first year from the date of your original purchase, you are responsible for all labor costs

associated with this warranty.

Warranty Exclusions: This warranty covers only repair or replacement, at our option, of defective Products or parts and

does not cover any other costs related to the Products including but not limited to: (a) normal maintenance and service

required for the Products and consumable parts such as fluorescent, incandescent or halogen light bulbs, mesh and char-

coal filters and fuses; (b) any Products or parts which have been subject to freight damage, misuse, negligence, accident,

faulty installation or installation contrary to recommended installation instructions, improper maintenance or repair (other

than by us); (c) commercial use of the Products or use otherwise inconsistent with its intended purpose; (d) natural wear

of the finish of the Products or wear caused by improper maintenance, use of corrosive and abrasive cleaning products,

pads, and oven cleaner products; (e) chips, dents or cracks caused by abuse or misuse of the Products; (f) service trips

to your home to teach you how to use the Products; (g) damage to the Products caused by accident, fire, floods, acts of

God; or (h) Custom installations or alterations that impact serviceability of the Products. If you are outside our service

area, additional charges may apply for shipping costs for warranty repair at our designated service locations and for the

travel cost to have a service technician come to your home to repair, remove or reinstall the Products. After the first year

from the date of your original purchase, you are also responsible for all labor costs associated with this warranty.

Limitations of Warranty. OUR OBLIGATION TO REPAIR OR REPLACE, AT OUR OPTION, SHALL BE YOUR SOLE AND

EXCLUSIVE REMEDY UNDER THIS WARRANTY. WE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR

SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE PRODUCTS.

THE EXPRESS WARRANTIES IN THE PRECEDING SECTION ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS

WARRANTIES. WE HEREBY DISCLAIM AND EXCLUDE ALL OTHER EXPRESS WARRANTIES FOR THE PRODUCTS,

AND DISCLAIM AND EXCLUDE ALL WARRANTIES IMPLIED BY LAW, INCLUDING THOSE OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. Some states or provinces do not allow limitations on the duration of an implied

warranty or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not

apply to you. To the extent that applicable law prohibits the exclusion of implied warranties, the duration of any applicable

implied warranty is limited to the same ten-year period described above. Any oral or written description of the Products is for

the sole purpose of identifying the Products and shall not be construed as an express warranty. Prior to using, implementing

or permitting use of the Products, you shall determine the suitability of the Products for the intended use, and you shall assume

all risk and liability whatsoever in connection with such determination. We reserve the right to use functionally equivalent

refurbished or reconditioned parts or Products as warranty replacements or as part of warranty service. This warranty is not

transferable from the original purchaser and applies in the United States and Canada.

To Obtain Service Under Limited Warranty: To qualify for warranty service, you must: (a) notify us at the address or

telephone number stated below within 60 days of the discovery of the defect; (b) give the model number and part identifi-

cation number and serial number; and (c) describe the nature of any defect in the Product or part. At the time of the

request for warranty service, you must present evidence of your proof of purchase and proof of the original purchase

date. If we determine that the warranty exclusions listed above apply or if you fail to provide the necessary documenta-

tion to obtain service, you will be responsible for all shipping, travel, labor and other costs related to the services.

Please check our website for any revisions, www.zephyronline.com.

Zephyr Ventilation Service Department, 2277 Harbor Bay Parkway, Alameda, CA 94502 1-888-880-8368

Limited Warranty

AUG14.0301

Proof of the original purchase

date is needed to obtain

service under warranty

La page charge ...

Zephyr AK8100ASBF Manuel utilisateur

Ce manuel convient également à

Zephyr AK8100ASBF Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents