AOG Portable Grill T-Series Manuel utilisateur

1

IMPORTANT:

READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.

DANGER:

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or the ﬁre department.

WARNING:

1. Do not store or use gasoline or other

ﬂammable vapors and liquids in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CODE AND SUPPLY REQUIREMENTS: This

grill must be installed in accordance with local

codes and ordinances, or, in the absence of local

codes, with the latest National Fuel Gas Code

(ANSI Z223.1/NFPA 54), or Natural Gas and

Propane Storage and Handling Installation Code

(CSA-B149.1).

This appliance and its dedicated manual shutoff

valve must be disconnected from the gas-supply

piping system when testing the system at pressures

in excess of ½ psig (3.5 kPa).

This appliance must be isolated from the gas-

supply piping system by closing its dedicated

manual shuto valve during any pressure testing

of the gas-supply system at pressures up to and

including ½ psig (3.5 kPa).

All electrical outlets in the vicinity of the grill must be

properly grounded in accordance with local codes,

or, in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70, or the Canadian

Electrical Code, CSA C22.1, whichever is applicable.

Keep all electrical-supply cords and fuel-supply

hoses away from any heated surface.

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

WARNING:

Improper installation, adjustment, alteration,

service, or maintenance can cause injury

or property damage. For proper installation,

refer to the installation instructions. For

assistance or additional information, consult

a qualiﬁed professional service technician,

service agency, or the gas supplier.

Proper operation of your grill

requires prompt and periodic

maintenance. See the SERVICING

AND CLEANING section for details.

Certiﬁed to: ANSI Z21.58

CSA 1.6

American Outdoor Grill • PO Box 4053 • La Puente, CA 91747

WARNINGS AND SAFETY CODES

INSTALLATION AND

OWNER’S MANUAL

US

®

C

GETTING STARTED

ONLY TO BE USED OUTDOORS

REV 4 - 2007100850

L-C2-442

PORTABLE OUTDOOR GAS GRILLS

24, 30, & 36 "T" Series

2

IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER L’INSTALLATION OU L’UTILISATION

GRIL EXTÉRIEUR DE GAZ DU PORTABLE

DANGER:

SI VOUS SENTEZ LE GAZ :

1. Coupez le gaz à l’appareil.

2. Éteignez-vous n’importe quelle ﬂamme nue.

3. Ouvrez le couvercle.

4. Si l’odeur continue, gardez loin de

l’appareil et appelez immédiatement

votre département de fournisseur ou de

feu de gaz.

AVERTISSEMENT:

1. Ne stockez pas ou n’employez pas

l’essence ou d’autres vapeurs et liquides

inﬂammables à proximité de ceci ou

d’aucun autre appareil.

2. Un cylindre de propane non relié pour

l’usage ne sera pas stocké à proximité

de ceci ou d’aucun autre appareil.

CONDITIONS DE CODE ET D’APPROVISIONNEMENT:

Ce gril doit être installé selon des codes et des ordonnances

locaux, ou, en l’absence des codes locaux, avec l’un ou l’autre

le plus défunt Code national de gaz de carburant (norme ANSI

Z223.1/NFPA 54), et Stockage de gaz naturel et de propane

et manipulation du code d’installation (CSA-B149.1).

Cet appareil et ses différents robinets d’isolement doivent être

démontés du gaz-fournissent le système sifﬂant en examinant

le système aux pressions au-dessus du ½ psig (kPa 3.5).

Cet appareil doit être isolé dans gaz-fournissent le système

siant par fermeture que ses diérents robinets d’isolement

manuels pendant tous les essais sous pression du gaz-

fournissent le système aux pressions jusques et y compris

le ½ psig (kPa 3.5).

Toutes les sorties électriques à proximité du gril doivent être

correctement fondues selon des codes locaux, ou en l’absence

de local code, avec le code électrique national, ANSI/NFPA

70, ou le code électrique canadien, CSA C22.1, celui qui est

applicable.

Maintenez tout électrique-fournissent des cordes et carburant-

fournissent des tuyaux partis de n’importe quelle surface de

chauffage.

INSTALLATEUR : Laissez ces instructions avec le consommateur.

CONSOMMATEUR : Maintenez pour la future référence.

AVERTISSEMENT:

L’installation inexacte, l’ajustement, le

changement, le service, ou l’entretien

peuvent causer des dommages ou des

dégats matériels. Référez-vous à ce manuel.

Pour de l'aide ou des renseignements

supplémentaires, consultez un technicien

professionnel qualifié de service, une

agence de service ou le fournisseur de gaz.

• Ce gril est pour ultilisation à l’extérieur seulement.

Si l’appareil est entreposé à l’intérieur, enlever les

bouteilles et les laisser à l’extérieur.

• Ne pas ranger le gril immédiatement aprés l’avoir utilisé.

le laisser refroidir avant de le déplacer ou de la ranger.

Le non respect de cette mesure de sécurité pourrait

entraîner un incendie causant des dommages à la

propriété, des blessures ou la mort.

• Ne pas utiliser cet appareil sous une surface combustible.

• Ne pas utiliser cet appareil sous un auvent. Le non

respect de cette mesure de sécurité pourrait entraîner

un incendie ou des blessures.

• Dégagement minimal entre les parois latérales et l’arriére

de l’appareil et la construction combustible (45.7 cm à

partir des parois latérales et 45.7cm à partir de l’arriére).

• Le régulareur de pression de gaz prévu avec cet appareil

de cuisson à gaz pour l’extérieur doit être utilisé. Ce

régulateur est réglé pour une pression de sortie de 5

pouces de colonne de l’eau pour le gaz naturel, et 10

pouces pour le propane.

• LE RÉGULATEUR INCLUS D’APPAREILS EST ÉVALUÉ

POUR LE MAXIMUM DE 1/2 (LIVRES PAR POUCE

CARRÉ). SI VOTRE OFFRE DE GAZ EST 1/2 PLUS

GRAND QUE (LIVRES PAR POUCE CARRÉ), UN

RÉGULATEUR ADDITIONNEL DOIT ÊTRE INSTALLÉ

AVANT LE GRIL. VOIR LA SECTION DE CONDITIONS

D’OFFRE DE GAZ POUR LA PRESSION APPROPRIÉE

D’OFFRE DE GAZ.

• Ne couvrez jamais la surface entière de cuisine ou de

gril de gauffreuses ou de casseroles. La surchauffe se

produira et les brûleurs ne seront pas très performants

quand la chaleur de combustion est emprisonnée au-

dessous de la surface à cuire.

• Ne pulvérisez jamais l’eau sur une unité chaude de gaz,

comme ceci peut endommager des composants de

porcelaine ou de fer de fonte.

• Une fuite de GPL peut causer une incendie ou une

explosion si enflammée entraînant des blessures

corporelles graves ou la mort.

• Communiquez avec le fournisseur de GPL pour les

réparations ou pour disposer de qules bouteille ou du

GPL non utilisé.

Certiﬁé à la norme: ANSI Z21.58 / CSA 1.6

SÛRETÉ ET CODES D’AVERTISSEMENT

INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE

À UTILISER UNIQUEMENT À L'EXTÉRIEUR

REV 4 - 2007100850

L-C2-442

3

TABLE OF CONTENTS

REV 4 - 2007100850

L-C2-442

GETTING STARTED

WARNINGS AND SAFETY CODES �� 1

INSTALLATION, OPERATION, AND SAFETY INFORMATION �� 4

GAS SAFETY INFORMATION �� 5

WARNING �� 5

WHEN USING PROPANE GAS �� 5

WHEN USING NATURAL GAS �� 5

INSTALLATION SAFETY GUIDELINES �� 5

OPERATING THE UNIT SAFELY AND CORRECTLY �� 5

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS �� 7

INSTALLATION REQUIREMENTS �� 8

OVERHEAD CONSTRUCTION AND EXHAUST HOOD REQUIREMENTS �� 8

REAR WALL CLEARANCES �� 9

SIDE WALL / CORNER WALL CLEARANCES (if applicable) �� 9

COMBUSTION AIR AND COOLING AIRFLOW �� 10

GAS-SUPPLY PLUMBING REQUIREMENTS �� 10

MODEL SPECIFICATIONS �� 11

AOG GRILL REPLACEMENT PARTS LIST �� 13

INSTALLATION

INSTALLATION �� 16

LOCATION PREPARATION �� 16

WHEELS AND CASTERS �� 16

CONNECT THE GAS SUPPLY �� 16

INSTALL THE COOKING GRIDS �� 17

INSTALL THE DRIP TRAY �� 17

INSTALL THE SIDEBURNER SHELF (IF EQUIPPED) �� 18

RIGID SHELF INSTALLATION �� 19

USE, CARE, & SERVICE

IDENTIFICATION OF GRILL CONTROLS �� 20

USING THE GRILL �� 21

LIGHTING (IGNITION) INSTRUCTIONS �� 23

ELECTRONIC LIGHTING �� 23

MANUAL LIGHTING�� 23

SHUTTING OFF THE UNIT �� 23

ROTISSERIE INSTRUCTIONS (IF EQUIPPED) �� 24

SERVICING AND CLEANING �� 25

CLEANING YOUR GRILL �� 25

CONTROL PANEL REMOVAL �� 27

BURNER REMOVAL�� 28

CONVERT GAS TYPE / CHECK BURNER ORIFICES �� 29

BURNER AIR SHUTTER ADJUSTMENT �� 31

VALVE "LOW" SETTING ADJUSTMENT �� 32

TROUBLESHOOTING �� 33

WARRANTY �� 34

4

1. The outdoor appliance and surrounding area MUST

remain clear of ﬂammable substances such as gasoline,

yard debris, wood, etc. Maintain a minimum horizontal

clearance of 18" (in all directions) from combustible

materials/items.

2. Do not block the 1" front air inlet along the bottom of

the control panel. See the COMBUSTION AIR AND

COOLING AIRFLOW section under INSTALLATION

REQUIREMENTS for details.

3. This unit must be installed so that the vent

openings on the cabinet remain clear and free at

all times. See the GAS SAFETY INFORMATION

section.

4. When using propane gas: the propane cylinder,

regulator, and rubber hose must be in a location

not subject to temperatures above 125° F (51° C).

5. The back burner cover or sideburner (if equipped)

must be removed before using the burner.

6. The ﬂames on each burner burn evenly along the

entire burner with a steady ﬂame (mostly blue). If

burner ﬂames are not normal, check and clean the

oriﬁce and burner/venturi tubes for insects and insect

nests. A clogged tube can lead to a ﬁre beneath the

unit. A proper ﬂame pattern will ensure safe operation

and optimal performance. Adjust the air shutter as

needed (see AIR SHUTTER ADJUSTMENT section).

7. The in-line gas valve or gas cylinder valve must always

be shut OFF when the unit is not in use.

8. The drip collector holes must be clear and unobstructed.

Excessive grease deposits can result in a grease ﬁre.

9. Wear gloves and use extreme caution whenever

installing and handling this product and its accessories

as certain components have sharp edges that can

cause personal injury.

WARNING: NEVER cover more than 75% of the cooking or grill surface with griddles or pans. Overheating will occur,

and burners will not perform properly when combustion heat is trapped below the cooking surface.

IMPORTANT

IN THE EVENT OF A GREASE FIRE, IMMEDIATELY SHUT OFF THE MAIN GAS VALVE TO THE UNIT. KEEP THE LID

OPEN AND ALLOW THE FIRE TO EXTINGUISH ITSELF. KEEP AT A SAFE DISTANCE. A THOROUGH INSPECTION BY

A QUALIFIED PROFESSIONAL SERVICE TECHNICIAN SHOULD BE CONDUCTED BEFORE FUTURE USE OF YOUR

UNIT. THE SERVICE TECHNICIAN WILL CHECK THE SYSTEM FOR GAS LEAKS AND WILL CHECK ALL ELECTRICAL

WIRING FOR DAMAGE. ALL GAS LEAKS AND WIRING MUST BE REPAIRED PRIOR TO FUTURE USE.

The unit serial number tag can be found afﬁxed to the grill body behind the control panel (on an

aluminum tag) and on the underside of the drip tray handle (on a thermal label). It is recommended

that the drip tray ﬁrst be removed and cleaned / emptied of its contents, then turned over to view.

The unit rating label is located inside of the control panel.

INSTALLATION, OPERATION, AND SAFETY INFORMATION

5

WARNING

This appliance MUST be installed and operated according to the information below.

FAILURE TO PROPERLY VENT THE GRILL CABINET MAY RESULT IN A FIRE OR EXPLOSION CAUSING

PROPERTY DAMAGE, BODILY INJURY, OR DEATH.

A leaking gas connection or valve unintentionally left open will create a hazard.

WHEN USING PROPANE GAS

• Propane gas (also known as L.P. gas) is heavier than air and will accumulate or pool in an inadequately

vented enclosure or recessed area.

• If a pool of propane gas is ignited, an explosion will occur. Adequate venting at the ﬂoor level of the cabinet

eliminates this danger.

• DO NOT store a spare propane-gas cylinder in or near the unit.

WHEN USING NATURAL GAS

• Natural gas is lighter than air and will accumulate at the top of an inadequately vented enclosure.

• If an accumulation of natural gas is ignited, an explosion will occur. Adequate venting at the top of the cabinet

eliminates this danger.

INSTALLATION SAFETY GUIDELINES

THIS UNIT MUST BE INSTALLED SO THAT THE VENT OPENINGS ON THE CABINET REMAIN CLEAR AND

FREE AT ALL TIMES.

The gas cylinder, regulator, and rubber hose must be in a location not subject to temperatures above

125° F (51° C).

IF A PROPANE CYLINDER IS INSTALLED INSIDE OF THE CABINET, THE GUIDELINES FOUND IN THE SAFE

USE & MAINTENANCE OF PROPANE GAS CYLINDERS SECTION MUST BE FOLLOWED.

WHEN OPERATING THIS GAS APPLIANCE, ALL INSTRUCTIONS AND WARNINGS

MUST BE OBSERVED. FAILURE TO DO SO MAY RESULT IN A FIRE OR EXPLOSION

CAUSING PROPERTY DAMAGE, BODILY INJURY, OR DEATH.

Every time you use the unit, make sure that:

1. The area around the unit is clear and free from combustible materials, gasoline and ﬂammable vapors/liquids.

2. There is no blockage of the airﬂow through the vent openings located on the cabinet.

3. The hose is inspected (if applicable). See SAFE USE & MAINTENANCE OF PROPANE-GAS CYLINDERS section.

DO NOT store any combustible materials, gasoline, and any other ﬂammable vapors/liquids in the vicinity of the

unit. Provide adequate clearance for servicing and operation.

GAS SAFETY INFORMATION

OPERATING THE UNIT SAFELY AND CORRECTLY

6

U

L

Fig. 6-1 type coupleur de ﬁl de point culminant d’I

Valve

de

décompression

QCC

Type 1

Valve

Ajustage de précision

en laiton de ﬁl de

point culminant

Indicateur

de niveau

de liquide

(facultatif)

Écrou de main avec le

ﬁl de point culminant.

Régulateur

Passage

Tuyau

Volant de commande

main dans le sens des aiguilles d’une montre pour engager les

ﬁls et pour serrer jusqu’à ce que douillettement. L’utilisation des

pinces ou de la clé ne devrait pas être nécessaire. Seulement

le propane marqué par cylindres doit être employé.

Pour débrancher: Tournez l’écrou de main dans le sens

contraire des aiguilles d’une montre jusqu’à isolé (ﬁg. 6-1).

Important: Avant d’employer le unité, et ensuite chaque

fois que le cylindre est enlevé et rattaché,

examinez tous les raccordements pour

déceler les fuites. Arrêtez les valves de unité

et ouvrez la valve principale de cylindre, puis

vériﬁez les raccordements avec de l’eau

savonneux. Réparez toutes les fuites avant

d’allumer le unité.

ATTENTION: Tournez toujours la valve principale de cylindre

de propane au loin après chaque utilisation,

et avant de déplacer le unité et le cylindre, ou

débrancher l’accouplement. Cette valve doit

rester fermée et le cylindre a débranché alors

que l’appareil n’est pas en service, quoique

l’écoulement de gaz soit arrêté par un dispositif

de sûreté quand le coupleur est débranché.

Inspectez soigneusement l’ensemble de tuyau chaque fois

avant que le gaz soit allumé. Un tuyau ﬁssuré ou efﬁloché doit

être immédiatement remplacé.

Si l'appareil est stocké à l'intérieur, le cylindre doit être disconnected

et a enlevé. Des cylindres Disconnected doivent être stockés

dehors, hors de la portée des enfants, avec les prises de valve

ﬁletées étroitement installées, et ne doivent pas être stockés dans

un bâtiment, le garage, ou n'importe quel autre secteur inclus.

POUR VOTRE SÛRETÉ

a. Ne stockez pas un cylindre de gaz disponible de propane

dessous ou ne vous approchez pas de cet appareil.

b. Ne remplissez jamais cylindre au delà de 80 pour cent de

plein.

c. SI L’INFORMATION DANS “A” ET “B” N’EST PAS SUIVIE

EXACTEMENT, UN FEU CAUSANT LA MORT OU DES

DOMMAGES SÉRIEUX PEUT SE PRODUIRE.

IMPORTANT POUR VOTRE SÛRETÉ

LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE.

En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements.

LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.

CYLINDRE ET CONDITIONS ET

CARACTÉRISTIQUES DE CONNECTEUR

a. Les bouteilles, les vannes et les tuyaux de propane doivent

être entretenus et inspectés avant chaque utilisation. Ils

doivent être remplacés en cas de dommages visibles. Si

le tuyau est coupé ou présente des signes d’abrasion ou

d’usure, il doit être remplacé avant utilisation (voir e.).

b. Cette unité, lorsqu'elle est utilisée avec une bouteille, doit

être connectée à une bouteille standard de gaz propane de

5 gallons (20 lb) équipée d'un dispositif anti-débordement

répertorié. L’appareil est obligatoire sur toutes les bouteilles

vendues depuis le 1er octobre 1998 aﬁn d’empêcher tout

remplissage excessif.

c. Les dimensions du cylindre doivent être d'environ 12 "(30,5 cm)

de diamètre et 18" (45,7 cm) de hauteur. Les bouteilles doivent

être construites et marquées conformément aux spéciﬁcations

du ministère des Transports (DOT) pour les bouteilles à gaz LP

ou à la norme relative aux bouteilles, sphères et tubes pour le

transport des marchandises dangereuses et à la Commission,

CAN / CSA-B339, selon le cas.

d. Le cylindre doit inclure un collier pour protéger la valve

de cylindre et le circuit d’alimentation de cylindre doit être

assuré le retrait de vapeur.

e. Le montage du régulateur de pression et le ﬂexible (Fig. 6-1)

fourni avec cet appareil au gaz en plein air (modèles au

propane seulement) doit être utilisé. Assemblées d'origine et

régulateur de pression et le tuyau de remplacement doivent

être ceux spéciﬁés par le fabricant pour le raccordement d'un

dispositif de cylindre de liaison identiﬁée comme de type I

par le ANSI Z 21.58/CGA 1.6 (voir liste des pièces pour les

informations de commande).

f. La valve de cylindre de gaz de propane doit être équipée

d’un dispositif d’accouplement de raccordement de

cylindre, décrit comme type I dans la norme déﬁnie dans le

e. de paragraphe ci-dessus. Ce dispositif est généralement

décrit comme coupleur de ﬁl de point culminant.

g. Si votre cylindre de gaz de propane vient avec une prise

de la poussière, placez le bouchon anti-poussière sur la

sortie de valve de cylindre toutes les fois que le cylindre

n’est pas en service.

OPÉRATION DE COUPLEUR

Pour relier le regulator/hose à l’ajustage de précision de

valve de cylindre de gaz de propane: Serrez l’écrou de main

sur le régulateur au-dessus de l’ajustage de précision de ﬁl

de point culminant sur la valve de cylindre. Tournez l’écrou de

1

2

3

4

FIXATION DU CYLINDRE DE GAZ DE PROPANE

1. Ensemble cylindre-

propane gaz dans le

manchon de support.

3. Serrer les vis de serrage pour ﬁxer

le cylindre.

2. Suivez les instructions

ci-dessus pour connecter

l’alimentation.

Renforcer

Fig. 6-2

Fig. 6-3 Fig. 6-4

Connectez-vous

à fournir

UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE

7

U

L

Fig. 7-1 Type I Acme thread coupler

Pressure

relief

valve

QCC

Type 1

valve

Brass Acme

thread ﬁtting

Liquid level

indicator

(optional)

Hand nut with Acme

thread

Regulator

Vent

Hose

Hand wheel

The use of pliers or a wrench should not be necessary. Only

cylinders marked “propane” may be used.

To disconnect: Turn the hand nut counterclockwise until

detached (Fig. 7-1).

Important: Before using the unit, and after each time

the cylinder is removed and reattached,

check the hose for wear (see a.) and check

all connections for leaks. Turn off the unit

valves and open the main cylinder valve,

then check connections with soapy water.

Repair any leaks before lighting the unit.

CAUTION: Always turn the propane cylinder main valve

off after each use, and before moving the unit

and cylinder or disconnecting the coupling.

This valve must remain closed and the

cylinder disconnected while the appliance

is not in use, even though the gas ﬂow is

stopped by a safety feature when the coupler

is disconnected.

Carefully inspect the hose assembly each time before the

gas is turned on. A cracked or frayed hose must be replaced

immediately.

If the appliance is stored indoors, the cylinder must be

disconnected and removed. Disconnected cylinders must be

stored outdoors, out of the reach of children, with threaded

valve plugs tightly installed, and must not be stored in a

building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER ﬁll the cylinder beyond 80-percent full.

c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED

EXACTLY, A FIRE CAUSING DEATH OR SERIOUS

INJURY MAY OCCUR.

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER/CONNECTOR REQUIREMENTS

a. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and inspected before each use

of appliance. They must be replaced if there is any visible

damage. If hose is cut or shows excessive abrasion or wear,

it must be replaced before using appliance (see e.).

b. This unit, when used with a cylinder, should be connected

to a standard 5-gallon (20 lb.) propane-gas cylinder

equipped with a listed overﬁlling prevention device. The

device has been required on all cylinders sold since

October 1,1998, to prevent overﬁlling.

c. Cylinder dimensions should be approximately 12" (30.5

cm) in diameter and 18" (45.7 cm) high. Cylinders must

be constructed and marked in accordance with the U.S.

Department of Transportation (D.O.T.) Speciﬁcations for

LP-Gas Cylinders, or the Standard for Cylinders, Spheres,

and Tubes for Transportation of Dangerous Goods and

Commission, CAN/CSA-B339, as applicable.

d. The cylinder used must include a collar to protect the

cylinder valve, and the cylinder supply system must be

arranged for vapor withdrawal.

e. The pressure regulator and hose assembly (Fig. 7-1)

supplied with this outdoor gas appliance (L.P. models

only) must be used. Original and replacement pressure

regulator and hose assemblies must be those speciﬁed by

the manufacturer for connection with a cylinder connecting

device identiﬁed as Type I by the ANSI Z 21.58/CGA 1.6

(see PARTS LIST for ordering information).

f. The propane-gas cylinder valve must be equipped with

a cylinder connection device, described as Type I in the

standard deﬁned in paragraph e. above. This device is

commonly described as an Acme thread coupler.

g. If the propane-gas cylinder comes with a dust plug, place

the dust cap on the cylinder valve outlet whenever the

cylinder is not in use.

COUPLER OPERATION

To connect the regulator/hose assembly to the propane-

gas cylinder valve ﬁtting: Press the hand nut on the regulator

over the Acme thread ﬁtting on the cylinder valve. Turn the hand

nut clockwise to engage the threads and tighten until snug.

SECURING THE PROPANE-GAS CYLINDER

1. Set the propane-gas

cylinder into the support

sleeve.

3. Tighten the thumb screws to secure

the cylinder.

2. Follow the instructions

above to connect supply.

Tighten

Fig. 7-2

Fig. 7-3 Fig. 7-4

Connect

to supply

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

8

Installation must be performed by a qualiﬁed professional

service technician.

This unit is designed for outdoor use only. DO NOT use this

unit inside a building, garage, or enclosed area. DO NOT use

this unit in or on a recreational vehicle or boat.

OVERHEAD CONSTRUCTION AND EXHAUST

HOOD REQUIREMENTS

A minimum 5 foot clearance is required between the cooking

surface and the overhead construction.

When installed under combustible overhead construction,

the area above the cooking surface of the unit must be

covered with an exhaust hood. The exhaust hood provides

the protection for the combustible overhead construction.

See exhaust hood information below and Fig. 8-1.

Important: DO NOT use this appliance under unprotected

combustible overhead construction.

When installed under overhead non-combustible construction,

an exhaust hood is highly recommended; see exhaust hood

information below and Fig. 8-1.

Exhaust Hood

When using an exhaust hood, the area above the cooking

surface of the grill must be covered with a hood larger than

the cooking area of the grill, and with a minimum of 1200

CFM (cubic feet per minute) rated exhaust fan for proper

outdoor application.

INSTALLATION REQUIREMENTS

Fig. 8-1 Overhead requirements

Min.

5'

OVERHEAD CONSTRUCTION

EXHAUST

HOOD

Combustible overhead

construction:

Exhaust hood required

Non-combustible

overhead construction:

Exhaust hood highly recommended

N

O

N

C

O

M

B

U

S

T

I

B

L

E

W

A

L

9

REAR WALL CLEARANCES

For the minimum clearances between the unit and rear walls,

your setup must fall within one (or more) of the following:

A. Clearance between unit and strictly non-combustible

rear wall

(i.e. brick wall, see Fig. 9-1)

• The unit must have a minimum clearance of 4" from

the non-combustible rear wall.

(To allow for proper ventilation and prevent dangerous

overheating.)

B. Clearance between unit and a protected combustible

rear wall

(i.e. a non-combustible wall in front of a combustible wall

to serve as a barrier. This can be accomplished by brick,

or a metal stud ﬁnished with non-combustible substrate,

see Fig. 9-2)

• The unit must have a minimum clearance of 14" from

the protected combustible rear wall.

(The 4" non-combustible material plus an additional 10"

clearance between the unit and protected rear wall.)

C. Clearance between unit and combustible rear wall

• The unit must have a minimum clearance of 18" from

the combustible rear wall (see Fig. 9-3).

SIDE WALL / CORNER WALL CLEARANCES

(if applicable)

The unit must have a minimum clearance of 24" from any

side walls (to account for variables in airﬂow that could affect

performance). See Fig. 9-4.

INSTALLATION REQUIREMENTS (Cont.)

Fig. 9-3 Clearance 'C' Diagram

Combustible

Min.

18"

(Clearance required for

rear wall)

Fig. 9-1 Clearance 'A' Diagram

Non-combustible

Min.

4"

(Clearance required for

rear wall)

Fig. 9-2 Clearance 'B' Diagram

Min.

14"

Non-combustible

substrate

Non-combustible 4"

Com-

bustible

(Clearance required for

rear wall)

Fig. 9-4 Side/corner wall clearance

Min.

24"

10

The control panel MUST remain removable for servicing (see

CONTROL PANEL REMOVAL section).

COMBUSTION AIR AND COOLING AIRFLOW

Proper airﬂow (front-to-back, Fig. 10-1) MUST be maintained

for the unit to perform as it was designed. If airﬂow is blocked,

overheating and poor combustion will result. Do not block the

1" front air inlet along the bottom of the control panel.

CAUTION: Wind blowing into or across the rear oven lid

vent (Fig. 10-3) can cause poor performance

and/or dangerous overheating. Orient the grill

so that the prevailing wind blows toward the

front of the grill (Fig. 10-2). A wind deﬂector

is available for purchase to assist in proper

airﬂow during windy conditions. See Table

1 for model numbers. Follow the instructions

included with the wind deﬂector for installation.

GAS-SUPPLY PLUMBING REQUIREMENTS

For natural gas or a household propane system, rigid

1

/

2

" or

3

/

4

" black steel pipe or local code-approved pipe is required

to conduct the gas supply to the unit. Contact your local gas

supplier. Connect this pipe to the C.S.A.-approved quick

connect hose (attached). Apply only joint compounds that are

resistant to all gasses on all NPT pipe ﬁttings except ﬂare

ﬁttings. Make sure to tighten all ﬁttings securely.

Note: If

1

/

2

" pipe is used with natural gas, it should be

no longer than 20'.

Important: A shut-off valve (not included) in the gas

line is required. It provides for safety when

the unit is not in use and for convenient

maintenance and repair. It must be installed

within 6 feet of the unit and must be easily

accessible. Use a pipe joint compound

resistant to all gasses on all male ﬁttings

except ﬂare ﬁttings.

GAS SUPPLY AND MANIFOLD PRESSURES:

For natural gas - normal 7" water column (w.c.), minimum

5", maximum 10

1

/

2

". For propane gas - normal 11" w.c.,

minimum 10", maximum 13".

INSTALLATION REQUIREMENTS (Cont.)

CORRECT

PLACE GRILL SO PREVAILING WIND

BLOWS TOWARD FRONT OF GRILL

Fig. 10-2 Airﬂow direction - CORRECT

Fig. 10-1 Airﬂow diagram

YOU MUST PROTECT REAR OVEN VENT FROM

PREVAILING WIND

Rear oven lid vent

INCORRECT

Fig. 10-3 Airﬂow direction - INCORRECT

(1" front air inlet)

11

MODEL SPECIFICATIONS

24" 30" 36"

Main burner quantity

N/P oriﬁce drill size

2

1.82mm / 1.16mm

3

#50 / 1.16mm

3

#49 / #56

Backburner*

N/P oriﬁce drill size

#53 / #64 #52 / #62 #52 / #62

Sideburner*

N/P oriﬁce drill size

#53 / #63 #53 / #63 #53 / #63

Wind deﬂector model # (not included)

24-B-24 30-B-24A 36-B-24

*

If equipped

Grill

model

HARDWARE KIT OPTIONS ORIFICE KIT

• 10ft. quick disconnect

hose

• convertible regulator

• ﬁttings

OR

• Convertible regulator

• ﬁttings

• Main burner / I.R.

burner oriﬁces

• Sideburner oriﬁces

• Backburner

• Conversion label

24"

CK-41-NAT CK-42-NAT 24-B-52

30"

CK-41-NAT CK-42-NAT 30-B-52A

36"

CK- 41-NAT CK-42-NAT 36-B-52

A hardware kit and oriﬁce kit must be purchased when converting.

Call your dealer for ordering information.

Table 1 - Product Speciﬁcations

Table 2 - Propane To Natural Gas Conversion Kits

12

MODEL SPECIFICATIONS (Cont.)

Model

Height Width Depth

Floor to top

(with oven)

Floor to top

of shelf

(C)

Left to right Front to back

Cart base

(D)

Shelf to shelf

(E)

Cart base

(F)

Maximum

outer

(G)

Open (A)

Closed

(B)

24"

59" 48

1

/2" 37" 25" 50" 22

1

/4" 24

3

/4"

30"

59" 48

1

/2" 37" 31" 56" 22

1

/4" 24

3

/4"

36"

59" 48

1

/2" 37" 37

1

/4" 62

1

/4" 22

1

/4" 24

3

/4"

G

C

F

E

B

D

A

Fig. 12-1

Table 3 - Grill Dimensions

13

IMPORTANT

This AOG oven and backburner (if equipped)

are fully pre-assembled and tested at the

factory.

DO NOT attempt to remove the oven and

backburner from the barbecue prior to

or during installation or damage to the

connecting gas line and igniter wiring may

occur.

The plastic straps that secure the oven to

the barbecue unit must be removed and

discarded prior to lighting.

Replacement parts can

be ordered from your

local AOG dealer.

AOG GRILL REPLACEMENT PARTS LIST

24" model shown

1

2

3

4

5

6

7

8

9

13

17

18

19

24

10

22

23

12

11

14

15

14

AOG GRILL REPLACEMENT PARTS LIST (Cont.)

24" 30" 36"

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

1. Stainless cooking grid (set of 2 or 3) 24-B-11A 1 30-B-11A 1 36-B-11A 1

2. Vaporizer panel 24-B-05-02 2 30-B-05-02 3 36-B-05-02 3

3. Main burner 24-B-06 2 24-B-06 3 24-B-06 3

4. Backburner* 24-B-17A 1 30-B-17A 1 30-B-17A 1

5.

Oven hood thermometer 23305 1 23305 1 23305 1

6.

Oven lid 24-B-25A 1 30-B-25A 1 36-B-25A 1

7. Single sideburner shelf* 24-C-02 1 24-C-02 1 24-C-02 1

8. Warming rack 24-B-02A 1 30-B-02A 1 36-B-02A 1

9. Drip tray with match holder 3085 1 3085 1 3085 1

10. Control panel w/ backburner, w/ sideburner 24-C-26T 1 30-C-26T 1 36-C-26T 1

or Control panel w/o backburner, w/o sideburner † 24-C-27T 1 30-C-27T 1 36-C-27T 1

11. Valve manifold w/ backburner, w/ sideburner (nat. gas) 24-C-08T 1 30-C-08T 1 36-C-08T 1

or Valve manifold w/ backburner, w/ sideburner (L.P. gas) 24-C-08TP 1 30-C-08TP 1 36-C-08TP 1

or Valve manifold w/o backburner, w/o sideburner (nat. gas)† 24-C-34T 1 30-C-34T 1 36-C-34T 1

or Valve manifold w/o backburner, w/o sideburner (L.P. gas)† 24-C-34TP 1 30-C-34TP 1 36-C-34TP 1

12. Main burner igniter assy only 24-B-04T 2 24-B-04T 3 24-B-04T 3

13. Main burner valve w/ igniter assembly 24-B-51T 2 24-B-51T 3 24-B-51T 3

14. Backburner valve * 24-B-35T 1 24-B-35T 1 24-B-35T 1

15. Sideburner valve * 24-C-52T 1 24-C-52T 1 24-C-52T 1

16. Backburner igniter assy *† 24-B-03T 1 24-B-03T 1 24-B-03T 1

17. Large knob 24-B-37T 2 24-B-37T 3 24-B-37T 3

18. Small knob * 24-B-38T 1 24-B-38T 1 24-B-38T 1

19. Rigid shelf 24-C-01 1

‡

24-C-01 1

‡

24-C-01 1

‡

20. Convertible regulator (nat. models only) † PR-4 1 PR-4 1 PR-4 1

21. Propane regulator / hose assembly † 5110-07 1 5110-07 1 5110-07 1

or Natural gas QD hose † 5110-03 1 5110-03 1 5110-03 1

22. Door (left) 24-C-53L 1 30-C-53L 1 36-C-53L 1

23. Door (right) 24-C-53R 1 30-C-53R 1 36-C-53R 1

24. Caster kit (set of 4) 24-C-35 1 24-C-35 1 24-C-35 1

*

If equipped

† Not shown

‡ If not equipped with sideburner; two rigid shelves are supplied.

15

24" 30" 36"

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

1. Stainless steel motor 24-B-32 1 24-B-32 1 24-B-32 1

2. Spit prongs (set of 2) 24-B-18 1 24-B-18 1 24-B-18 1

3. Spit rod

5

/

8

" hex 24-B-33 1 30-B-33 1 36-B-33 1

4. Handle knob 24-B-09 1 24-B-09 1 24-B-09 1

2

4

1

3

ROTISSERIE KIT (if equipped)

AOG GRILL REPLACEMENT PARTS LIST (Cont.)

16

LOCK

UNLOCK

LOCATION PREPARATION

Prepare a ﬂat, level surface capable of supporting

the weight of the portable grill and convenient to the

gas supply if connecting to a gas line.

WHEELS AND CASTERS

To lock a caster press down on the left lever until it

stops and the caster will not turn. To unlock, press

down on the right lever.

CONNECT THE GAS SUPPLY

Always ensure the orifices and regulator (if

equipped) are set for the gas type your unit is

to be installed to.

For connecting a propane unit to a portable

propane tank, read the safety warnings and follow

the instructions in the section SAFE USE AND

MAINTENANCE OF PROPANE GAS CYLINDERS.

For household propane or natural gas units:

1. Turn OFF the gas supply at the source. The

quick disconnect hose is pre-installed on the

valve manifold at the manufacturer. Run the

hose through the hole in the bottom rear of the

portable unit, to the gas supply.

2. A shut-off valve is required within 6 feet of the unit.

Connect the quick connect hose to the shut-off

valve (NPT) OR gas supply (NPT) using a pipe

joint compound resistant to all gasses (see Fig.

16-2). Tighten securely.

3. Turn all burner valves to the OFF position. Turn

the gas supply on. Then carefully check all gas

connections for leaks with a brush and soapy

water before lighting. NEVER USE A MATCH

OR OPEN FLAME TO TEST FOR LEAKS.

INSTALL THE VAPORIZER PANELS

Place the vaporizer panels directly onto the studs

on the burners. See Fig. 16-3. The panels allow heat

from the burners to be evenly distributed throughout

the cooking area. The panels are stainless steel and

will heat and cool quickly, making your barbecue

very responsive to the changes you specify in

grill temperature. They are rust resistant and may

be cleaned with standard oven cleaners. Some

discoloring will be seen with use. This is normal for

stainless steel and does not affect the function.

Fig. 16-1 Wheels and casters

INSTALLATION

Fig. 16-2 Connecting to a gas line

Gas supply (NPT)

Quick connect hose

(coming from unit)

NPT-to-NPT

shut-off valve

(required, not included,

must be installed within 6

feet of the unit)

Quick connector

(can be connected

directly to gas supply

stub if shut-off valve

installed in-line)

(Grill rear)

Quick connect

hose

Fig. 16-3 Install vaporizer panels

Place onto studs

17

INSTALL THE COOKING GRIDS

Carefully place each cooking grid onto the front and rear

grid rests of the grill. See Fig. 17-1.

INSTALL THE DRIP TRAY

Fully insert the drip tray into the bottom front of the control

panel. See Fig. 17-2.

INSTALL THE WARMING RACK

The warming rack (Fig. 17-3) is packed separately. To

install the warming rack, carefully insert the rack hangers

into the two holes in the back of the inner oven hood, then

lower the front of the rack to a level position.

Note: Removing the warming rack before using the

rotisserie will leave more clearance for the meat

being cooked (if applicable).

INSTALLATION (Cont.)

Fig. 17-1 Install cooking grids

Warming

rack

Fig. 17-3 Install warming rack

Fig. 17-2 Install drip tray

18

This shelf comes separate from the grill for

convenience in shipping. The sideburner shelf

must be installed using the following instructions

before hooking up the grill to a gas source.

INSTALL THE SIDEBURNER SHELF

1. Remove the protective plastic from the grill,

sideburner, and sideburner lids by carefully

peeling it off with your ﬁngers. Do not use tools.

2. Hold the sideburner shelf up against the left

side wall of the grill so that the holes in the shelf

line up with the four (4) threaded screw holes

in the side wall and the air-shutter end of the

sideburner venturi tube ﬁts around the brass

oriﬁce protruding from the side of the cart.

WARNING: It is critical for safety and for the

proper function of the sideburner

that the sideburner venturi tube with

air shutter be centered around and

completely cover the gas oriﬁce.

3. Insert and start screws with ﬁngers and then

tighten using a Phillips screwdriver.

Important:

Take caution to not cross-thread

when tightening the screws.

Note: Upon completion, the air shutter must still

ﬁt around the brass oriﬁce.

4. Connect the female connector on the end of the

hot surface igniter wire to the male connector

coming from inside the grill.

5. Place the burner cap on top of the burner, as

shown in Fig. 18-3.

6. Place the grid so that it rests on the front and

back lips of the sideburner opening (Fig. 18-4).

7. Proceed to the section on AIR SHUTTER

ADJUSTMENT and complete the installation by

adjusting the air shutter. This will also test the

sideburner installation.

Air-shutter oriﬁce placement - under shelf

Fig. 18-1

Connecting the igniter wires

Placing the burner cap

Fig. 18-2

Fig. 18-3

Final look

Fig. 18-4

Screw

Hole

Male

Female

Brass

oriﬁce

Air

shutter

Grate

Lid

Cap

Shelf

Air shutter oriﬁce placement - under shelf

Fig. 18-1

Connecting the igniter wires

Fig. 18-2

Screw

Electrode

insulator

Female

connector

Brass

oriﬁce

Air

shutter

Shelf

Insulator

Igniter wire

Venturi tube

4. Connect the female connector on the end of

the igniter wire to the male igniter connector

protruding from the bottom of the white insulator.

INSTALL THE SIDEBURNER SHELF (IF EQUIPPED)

19

RIGID SHELF INSTALLATION

Shelf support screws

View from under right shelf

This barbecue comes with two (2) rigid shelves that

must be attached. These can be attached using the

four support screws provided and a Phillips-head

screw driver.

Important:

Take caution to not cross-thread

when tightening the screws.

1. Hold the shelf inverted so that one of the corner

holes in the shelf lines up with the appropriate

upper screw hole in the barbecue.

2. Insert the screw, but do not tighten all the way so

that the shelf can be easily rotated around the ﬁrst

screw.

3. Line up the second corner hole in the shelf with

the remaining upper screw hole in the barbecue.

Insert a screw and tighten.

Note: You may lift the edge of the shelf upward

to gain better access during much of the

tightening of this screw.

4. Finally, insert the bottom screws on the left and right

side of the shelf and securely tighten all screws.

To detach, reverse the process above.

This barbecue comes with one rigid shelf that must

be attached. It can be attached using the four support

screws provided and a Phillips-head screwdriver.

Important:

Take caution to not cross-thread

when tightening the screws.

1. Insert the top two screws into the side of the

barbecue and screw them in about half way.

2. Line up the larger, bottom portion of the two

keyhole openings with the two top screws and ﬁt

the two keyhole openings over the two screws.

With the shelf pushed all the way against the

side of the barbecue, lower the shelf so that the

screws lock into the narrower, upper portions of

the keyholes.

Note: The shelf will now stay in place on it’s

own.

3. Insert the bottom two screws into their holes and

tighten them all the way.

4. Finally, tighten the upper two screws,

completely.

To detach, reverse the process above.

20

Side Burner

Left

main burner

control knob

Right

main burner

control knob

Backburner

control knob

(if equipped)

Side Burner

Center main burner

control knob

Control panel

screw(s)

Drip

tray

Right

main burner

control knob

Backburner

control knob

(if equipped)

Control panel

screw(s)

Drip

tray

Sideburner

control knob

(if equipped)

Left

main burner

control knob

Sideburner

control knob

(if equipped)

Fig. 20-1 24" model controls

Fig. 20-2 30" and 36" model controls

IDENTIFICATION OF GRILL CONTROLS

USE, CARE, & SERVICE

La page est en cours de chargement...

AOG Portable Grill T-Series Manuel utilisateur

AOG Portable Grill T-Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents