Shenzhen Liangming Technology LM80P2 Manuel utilisateur

LM80P2
Marque
Shenzhen Liangming Technology
Modèle
LM80P2
Taper
Manuel utilisateur

Ce manuel convient également à

User Manual
Model No. : LM80P2-0001AA, LM80S2-0001AA,
Test Model No. : LM80P2-0001AA
Company Name: Shenzhen Liangming Technology Co., Ltd.
Address: 808, Building 1, Optoelectronic R&D Building, Hangcheng
Avenue, Xixiang Street, Baoan District, Shenzhen,China
1. Overview
The LM80 SoC features a fully integrated 2.4GHz radio transceiver
and baseband processor for Wi-Fi 802.11b and Bluetooth® Smart
applications. The SoC can be used as a standalone application-specific
communication processor or as a wireless data link in hosted MCU
systems where ultra-low power is critical. The OPL1000 supports flexible
memory architecture for storing profiles, stacks and custom application
codes, and can be updated using Over-The-Air (OTA)technology.
Qualified Bluetooth Smart protocol stack and Wi-Fi TCP/IP stack are
stored in a dedicated ROM. The OPL1000 is equipped with dual
processors, ARM® Cortex®-M0 and M3, for handling different
processes. All software runs on the ARM® Cortex®-M0 processor while
more intensive application-specific activities run on the ARM®
Cortex®-M3 processor. The OPL1000 can be connected to any external
MCU through SPI, I2C or UART interfaces and sensors or other devices
through GPIOs. The transceiver interfaces directly to the antenna and is
fully compliant with the Wi-Fi 802.11b and Bluetooth 5.0 BLE standards.
With integrated antenna switch, RF balun,power amplifier (PA) and low
noise amplifier (LNA), the OPL1000 allows both Wi-Fi and Bluetooth
Smart to minimize PCB design area and external component
requirement.
2. FEATURES
The OPL1000 complies with ETSI EN 300 328 and EN 300 440 Class 2
(Europe), FCC CFR47 Part 15(US), and ARIB STD-T66 (Japan).
◼ Processors
◼ARM® Cortex®-M3 Application Processor
◼ARM® Cortex®-M0 Link Controller
◼ Wi-Fi
◼ 802.11b up to 11Mbps
◼ Supports STA mode
◼ WPA/WPA2 security supported
◼ Automatic beacon scanning and discovery
◼ Built-in TCP/IP stack
◼ Integrated dual power amplifiers: low (-2 dBm), high (+10 dBm)
◼ Bluetooth Smart
◼ Compliant with Bluetooth 5.0 BLE specifications with 2Mbps rate
capability
◼ Slave mode support
◼ All GATT-based profiles supported
◼ Built-in BLE stack
◼ 0 to 10 dBm transmit output power
◼ -93 dBm receive sensitivity
◼ HW Crypto Engine
◼ AES-128/256 bits Encryption
◼ P-192/256 ECDH (Elliptic Curve Diffie-Hellman) Key Generation
◼ SHA2
◼ TRNG
◼ Power Management
◼ Integrated Buck DC-DC converter
◼ General purpose, capture and sleep timers
◼ FW OTA (Over-The-Air) update support
◼ Digital Interfaces
◼ General purpose I/Os: 24
◼ Two UARTs with hardware flow control up to 3Mbps
◼ Three SPI+™ interfaces
◼ One I2C bus at 100 kHz, 400 kHz
◼ Analog Interfaces
◼ 10-bit Auxiliary ADC inputs up to 16 channels
◼ Six GPIO pins with 16mA driving capability
◼ Six PWMs
◼ Radio Transceiver
◼ Fully integrated dual-mode 2.4 GHz CMOS transceiver
◼ Single wire antenna: no external matching and no external T/R switch
required
◼ Package
◼ 48-pin QFN, 6 mm x 6 mm
3. Applications
•WiFi scale
•WiFi intelligent door lock
•Wearable devices or healthcare devices
•Industrial remote control and telemetry
•Traffic, underground positioning and alarm
•Automatic data acquisition system
•Wireless data transmission; banking system
•Building automation, security, wireless monitoring of computer
room equipment, access control system
•Intelligent home and industrial control
FCC Modular Usage Statement
The requirement for KDB 996369 D03:
2.2 List of applicable FCC rules
FCC CFR Title 47 Part 15 Subpart C Section 15.247
2.3 Summarize the specific operational use conditions
The module has been certified for Fix, Mobile, Portable applications. This transmitter must
not be co‐located or operating in conjunction with any other antenna or transmitter.
2.4 Limited module procedures
Not applicable
2.5 Trace antenna designs
Not applicable
2.6 RF exposure considerations
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This modular must be installed and operated with a minimum
distance of 20 cm between the radiator and user body.
2.7 Antennas
This module contains three Antenna type. The details information list bellow.
PCB Antenna:1.2dBi
IPEX Antenna:1.5dBi
FPCB Antenna:-3.49dBi
2.8 Label and compliance information
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed andused in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
‐Consult the dealer or an experienced radio/TV technician for help.
If the FCC identification number is not visible when the module is installed inside another device,
then the outside of the device into which the module is installed must also display a
label referring to the enclosed module. This exterior label can use wording such as the
following: “Contains Transmitter Module FCC ID: 2AQJL-LM80P2 Or Contains FCC ID: 2AQJL-
LM80P2”
IC STATEMENT
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Afin d'éviter la possibilité de dépasser les limites d'exposition aux fréquences radio de la ISEDC CNR102, la
proximité humaine à l'antenne ne doit pas être inférieure à 20 cm (8 pouces) pendant le fonctionnement normal.
2.9 Information on test modes and additional testing requirements
The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247) list
on the grant, and that the host product manufacturer is responsible for compliance to any other
FCC rules that apply to the host not covered by the modular transmitter grant of
certification. The final host product still requires Part 15 Subpart B compliance testing
with the modular transmitter installed when contains digital circuity.
2.10 Additional testing, Part 15 Subpart B disclaimer
When testing host product, the host manufacture should follow FCC KDB Publication 996369
D04 Module Integration Guide for testing the host products. The host manufacturer may operate
their product during the measurements.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Shenzhen Liangming Technology LM80P2 Manuel utilisateur

LM80P2
Marque
Shenzhen Liangming Technology
Modèle
LM80P2
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Autres documents