Ohsung Electronics S904-SD-WF Manuel utilisateur

S904-SD-WF
Ohsung Electronics
Marque
Ohsung Electronics
Modèle
S904-SD-WF
Taper
Manuel utilisateur
1
Manual
Customer Sindoh
Product Name W
Customer Model -
Customer P/N -
Supplier Model S904-SD-WF
OHSUNG ELECTRONICS CO., LTD.
2
CONTENTS
1. Features .......................................................................................................................................................................................... 3
1.1 General ......................................................................................................................................................................................... 3
1.2 Ordering Information ............................................................................................................................................................. 3
2. Product Specifications .............................................................................................................................................................. 3
2.1 Electrical Specifications ......................................................................................................................................................... 3
2.2 Standard Test Conditions..................................................................................................................................................... 4
2.3 Standard Rated Specification ............................................................................................................................................. 5
3
1. Features
1.1 General
IEEE® 802.11 b/g/n (20MHz/40MHz) (1x1) solution
Integrated PCB antenna
SIZE : 48mm x 28mm x 10mm
CMOS MAC, Baseband PHY, and RF in a single chip for 802.11 b/g/n compatible WLAN
Complete 802.11n solution for 2.4GHz band
72.2Mbps receive PHY rate and 72.2Mbps transmit PHY rate using 20MHz bandwidth
150Mbps receive PHY rate and 150Mbps transmit PHY rata using 40MHz bandwidth
Compatible with 802.11n specification
Backward compatible with 802.11b/g devices while operating in 802.11n mode
1.2 Ordering Information
Model Description
S904-SD-WF 802.11 b/g/n (HT20/HT40) Module
2. Product Specifications
2.1 Electrical Specifications
2.1.1 Absolute Maximum Ratings
Description Min. Typ Max. Unit
Storage Temperature -30 +80 ℃
Storage Humidity (40℃) 85 %
2.1.2 Operating conditions
Description Min. Typ Max. Unit
Supply Voltage 4 5 6 Vdc
Ambient Temperature -20 +70 ℃
Ambient Humidity (40℃) 85 %
4
2.2 Standard Test Conditions
The Test for electrical specification shall be performed under the following condition
Otherwise this following conditions, not guaranteed this performance
2.2.1 Ambient Condition
Description Min. Typ Max. Unit
Ambient Temperature 20 30 ℃
Ambient Humidity (40℃) 60 70 %
2.2.2 Power Supply Voltages
Input power Unit
VDD_5V 5V ± 0.5V
2.2.3 Current Consumption
Device state Code rate Output
power, dBm
Current consumption
Min Max
ON_Transmit
802.11b 11Mbps 17 180mA 260mA
802.11g 54Mbps 15 130mA 180mA
802.11n MCS 7 (HT20) 14 120mA 170mA
802.11n MCS 7 (HT40) 14 110mA 150mA
ON_Receive
802.11b 11Mbps N/A 50mA 80mA
802.11g 54Mbps N/A 50mA 80mA
802.11n MCS 7 (HT20) N/A 50mA 80mA
802.11n MCS 7 (HT40) N/A 50mA 80mA
2.2.4 ESD Information
ESD Unit
Air discharge ±8KV
Contact discharge ±4KV
5
2.3 Standard Rated Specification
Radio Performance under Typical Conditions: VDD @ 5.0V, temp. 25°C
Division Characteristic
WLAN Standard IEEE 802.11 b/g/n HT20/40, Wi-Fi compliant
Host Interface USB
Frequency Range 2.400GHz ~ 2.4835GHz (2.4GHz ISM Band)
Dimension L x W x H : 48 x 28 x 10 (typical) mm
Modulation 802.11b : DQPSK, DBPSK, CCK
802.11g/n : OFDM /64-QAM,16-QAM, QPSK, BPSK
Data Rate
802.11b: 1, 2, 5.5, 11Mbps
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps
Data Rate
(20MHz, 40MHz) 802.11n: MCS0, MCS1, MCS2, MCS3, MCS4, MCS5, MCS6, MCS7
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or
modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
and 2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain
laptop configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for reevaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product must
be labeled in a visible area with the following: “Contains FCC ID: OZ5-S904-SD-WF”. The grantee's
FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user’s manual of the end product which integrates this
module. The end user manual shall include all required regulatory information/warning as show
in this manual.
ISED Canada (IC) Statement
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
RF Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Required end product labeling:
Any device incorporating this module must include an external, visible, permanent marking
or label which states: “Contains IC: 21703-S904SDWF”
This radio transmitter (identify the device by certification number or model number if Category
II) has been approved by Industry Canada to operate with the antenna types listed below with
the maximum permissible gain indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this
device.
Canada, Industrie Canada (IC) Déclaration
Cet appareil numérique de classe B est conforme à la norme NMB-003.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio
exempts de licence.L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage adioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Déclaration d'exposition aux radiations:
Cet appareil est conforme aux limites d'exposition aux rayonnements définies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance
minimale de 20 centimètres entre le radiateur et votre corps.
Obligation d'étiquetage du produit final:
Tout dispositif intégrant ce module doit comporter un externe, visible, marquage permanent
ou une étiquette qui dit: "Contient IC : 9080A-SBWM3".
Cet émetteur radio ( identifier le dispositif par numéro de certification ou le numéro de modèle ,
si la catégorie II ) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne
énumérés ci-dessous avec le gain maximal admissible indiqué . types d'antennes non inclus dans
cette liste , ayant un gain supérieur au gain maximum indiqué pour ce type , sont strictement
interdits pour une utilisation avec cet appareil.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Ohsung Electronics S904-SD-WF Manuel utilisateur

S904-SD-WF
Ohsung Electronics
Marque
Ohsung Electronics
Modèle
S904-SD-WF
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents