Hitachi DK-H100 Operating Instructions Manual

Marque: Hitachi

Modèle: DK-H100

Taper: Operating Instructions Manual

Ce manuel convient également à

DK-Z50

HD COLOR CAMERA

DK-H100

OPERATING INSTRUCTIONS

Please read these operating instructions carefully for proper operation,

and keep them for future reference.

Note: The model and serial numbers of your product are important for you to keep for your

convenience and protection. These numbers appear on the nameplate located on bottom of the

product. Please record these numbers in the spaces provided below, and retain this manual for

future reference.

Model No.

Serial No.

SAFETY INSTRUCTIONS

Carefully read all safety messages in this manual and safety Instructions on your equipment.

Follow recommended precautions and safe operating practices.

SAFETY ALERT SYMBOL

This is the “Safety Alert Symbol.”

This symbol is used to call your attention to items or operations that could be dangerous to you or

other persons using this equipment. Read these messages and follow these instructions

carefully.

It is essential that you read the instructions and safety regulations before you attempt to assemble or use this

equipment.

The definitions of signal words are as follows:

WARNING: Personal danger

Warning notes indicate any condition or practice, which if not strictly observed, could result

in personal injury or possible death.

CAUTION: Possible damage to equipment

Caution notes indicate any condition or practice, which if not strictly observed or remedied,

could result in damage or destruction of the equipment.

NOTE: Notes indicate an area or subject of special merit, emphasizing either the product′s

capabilities or common errors in operation or maintenance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS COLOR

CAMERA TO RAIN OR MOISTURE.

AVERTISSEMENT

Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer l’appareil á la pluie ou á l’humidité.

Afin d’écarter tout risque d’électrocution, garder le coffret fermé.

Ne confier l’entretien de l’appareil qu á un personnel qualifié.

VORSICHT

Um Feuergefahr und die Gefahr eines eiektrischen Schiages zu vermeiden, darf das Gerät weder Regen

noch Feuchtigkeit ausgesetzt werden.

Um einen elektrischen Schiag zu vermeiden, darf das Gehäuse richt geöffnet werden.

Überiassen Sie Wartungsarbeiten stets nur einem Fachmann.

WARNING

CAUTION

NOTE

IMPORTANT SAFETY INSTRUCTIONS

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Heed Warnings

All warnings on the product and the operating instructions should be adhered to.

4. Follow Instructions

All operating and use instructions should be followed.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

6. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Water and Moisture

Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry

tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious damage to the product. Use only with a cart,

stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any

mounting of the product should follow the manufacturer's instructions, and should use a mounting

accessory recommended by the manufacturer.

9. Moving

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to

overturn.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these openings must not be blocked or covered.

The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.

This product should not be placed in a built-in installation such as a bookcase or rack unless proper

ventilation is provided or the manufacturer's instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If

company. For products intended to operate from battery power, or other sources, refer to the operating

instructions.

12. Grounding or Polarization

This product is equipped with a three-wire grounding-type plug a plug having a third (grounding) pin.

This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to

insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the

safety purpose of the grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed to that they are not likely to be walked on or pinched by items

placed upon or against them, paying particular attention to cords at plug, convenience receptacles, and

the point where they exit from the product.

14. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to

lightning and power-line surges.

15. Overloading

Do not overload wall outlets, extension cords or integral convenience receptacles as this can result in a

risk of fire or electric shock.

16. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage

points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on

the product.

17. Inflammable and Explosive Substance

Avoid using this product where there are gases, and also where there are inflammable and explosive

substances in the immediate vicinity.

18. Heavy Shock or Vibration

When carrying this product around, do not subject the product to heavy shock or vibration.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the

following conditions:

a. When the power-supply cord or plug is damaged.

b. if liquid has been spilled, or objects have fallen into the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating instructions. Adjust only

those controls that are covered by the operating instructions as an improper adjustment of other controls

may result in damage and will often require extensive work by a qualified technician to restore the

product to its normal operation.

e. If the product has been dropped or damaged in any way.

f. When the product exhibits a distinct change in performance-this indicates a need for service.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts

specified by the manufacturer or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety

checks to determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

WICHTIGE SICHERHEITSANWEISUNGEN

1. Alle Anweisungen lesen.

Vor Betrieb des Erzeugnisses sollten alle Sicherheits-und Bedienungsanleitungen gelesen werden.

2. Die Anweisungen aufbewahren.

Die Sicherheits-und Bedienungsanleitungen sollten fünftigen Bezug aufbewahrt werden.

3. Warnungen beachten.

Die Warnungen auf dem Erzeugnis und in den Bedienungsanleitungen solten beachtet werden.

4. Anweisungen befolgen.

Alle Bedienungsanleitung-und

Verwendungsanweisungen sollten befolgt werden.

5. Reinigung

Den Stecker des Geräts vor Reinigung aus der Steckdose ziehen. Keine flüssigen Reinigungsmittel

oder Aerosolreiniger verwenden. Zum Reinigen einen feuchten Lappen verwenden.

6. Zubehör

Nur vom-Hersteller des Erzeugnisses empfohlenes Zubehör verwenden, da es sonst zu Störungen

kommen kann.

7. Wasser und Feuchtigkeit

Dieses Erzeugnis nicht in der Nähe von Wasser verwenden - z.B, in der Nähe einer Badewanne, eines

Waschbeckens, einer Küchenspüle, eines Waschzubers, in einem nassen Keller, in der Nähe eines

Schwimmbeckens usw.

8. Aufstellung

Das Erzeugnis nicht auf einen unstabilen Wagen, Stand, Dreifuß, Träger oder Tisch stellen.

Das Erzeugnis kann sonst herunterfallen und ein kind oder einen Erwachsenen schwer verietzen.

Außerdem kann das Gerät schwer beschädigt werden. Nur mit einem Wagen, Stand, Dreifuß, Träger

oder Tisch verwenden, der vom Hersteller empfohlen oder mit dem Erzeugnis verkauft worden ist. Für

jegliche Anbringung sollten die Anweisungen des Herstellers befolgt werden, und das vom Hersteller

empfohlene Anbringungszubehör sollte verwendet werden.

9. Eine Kombination von Erzeugnis und Wagen sollte vorsichtig bewegt werden.

Schneller Halt, übermäßige Krafteinwirkung und unebene Oberflächen können Umkippen der

kombination von Erzeugnis und Wagen verursachen.

10. Ventilation

Schlitze und Öffnungen im Gehäuse dienen der Ventilation. Sie sind für zuverlässigen Betrieb des

Gerätes und Schutz vor Überhitzung erforderlich und dürfen nicht blockiert oder abgedeckt werden.

Die Öffnungen sollten niemals dadurch blockiert werden, daß, das Gerät auf ein Bett, ein Sofa, einen

Teppich oder eine ähnliche Oberfläche gestellt wird.

Das Gerät sollte nur dann in Einbauinstallierung wie in einem Bücherschrank oder einem Gestell

verwendet werden, wenn angemessene Ventilation vorgesehen ist bzw. Die Anweisungen des

Herstellers befolgt worden sind.

11. Stromversorgung

Dieses Erzeugnis sollte nur an der auf dem Typenschild angegebenen Stromversorgungsart betrieben

werden. Wenn Sie nicht sicher sind, was für eine Stromversorgung Sie haben, so wenden Sie sich bitte

an Ihren Erzeugnishändler oder an das lokale Elektrizitätswerk. Beziehen Sie sich für Batteriebetrieb

oder andere Stromquellen vorgesehene Erzeugnisse bitte auf die Bedienungsanleitungen.

12. Erdung oder Polarisierung

Dieses Erzeugnis ist mit einem Schutzkontaktstecker mit drei Leitern ausgerüstet, mit einem

Erdungskontakt. Dieser Stecker paßt nur in ein schuko-Steckdose. Dies ist eine

Sicherheitsmaßnahme. Wenn Sie den Stecker nicht in die Steckdose stecken können, so wenden Sie

sich bitte an ihren Elektriker, damit er die veraltete Schuts des Schutzkontaktsteckers unwirksam.

13. Netzkabelschutz

Netzkabel sollten so verlegt werden, deß möglichst nicht darauf getreten wird und daß sie nicht

eingeklemmt werden, mit besonderer Beachtung der kabel an Stackern, Verlängerungskabeln und dem

Austritt des Kabels aus dem Erzeugnis.

14. Blitzschlag

Für zusätzlichen Schutz des Erzeugnisses während eines Gewitters oder bei Nichtverwendung für lange

Zeit den Stecker aus der Steckdose ziehen. Dies verhütet Beschädigung durch Blitzschlag und

Netzspannungsstöße.

15. Überlastung

Wandsteckdosen, Verlängerungskabel und eingebaute Bequemlickkeitssteckdosen nicht überlasten, da

dies Feuer oder elektrischen Schlag verursachen kann.

16. Eindringen von Fremdkörpern und Flüssigkeit

Niemals Objekte irgendwelcher Art durch die Öffnungen in das Gerät schieben, da diese unter hoher

Spannung stehende Teile berühren oder kurzschließen können, wodurch es zu Feuer oder elektrischem

Schlag kommen kann. Niemals Flüssigkeiten irgendwelcher Art auf das Erzeugnis verschütten.

17. Entflammbare und explosive Substanzen

Vermeiden Sie Verwendung dieses Erzeugnisses an Orten mit Gasen bzw. entflammbaren oder

explosiven Substanzen in der direkten Umgebung.

18. Starke stöße oder Vibrationen

Setzen Sie das Erzeugnis beim Transport nicht starken Stößen oder Vibrationen aus.

19. Wartung

Versuchen Sie nicht, dieses Erzeugnis Selbst zu warten, da Sie sich durch Öffnen bzw. Entfernen von

Abdeckungen hohen Spannungen und sonstigen Gefährdungen ausserzen können.

Beziehen Sie sich für jegliche Wartung auf qualifiziertes Wartungspersonal.

20. Beschädigung, die Wartung erfordert

Ziehen Sie den Stecker dieses Erzeugnisses aus der Steckdose und wenden Sie sich an qualifiziertes

Wartungspersonal, wenn eine der folgenden Bedingungen vorliegt:

a. Wenn das Netzkabel oder der Stecker beschädigt ist.

b. Bei Eindringen von Flüssigkeit oder Fremdkörpern in das Gerät.

c. Wenn das Erzeugnis Regen oder Wasser ausgesetzt worden ist.

d. Wenn das Erzeugnis bei Befolgen der Bedienungsanleitungen nicht normal funktioniert.

Nur die Regelelemente verstellen, die in den Bedienungsanleitungen behandelt werden, da

unangemessene Einstellung anderer Regelelemente Beschädigung verursachen kann und oft

beträchtliche Arbeit durch einen qualifizierten Techniker erfordert, um das Erzeugnis wieder, zu

normalem Betrieb zurückzubringen.

e. Wenn das Erzeugnis fallen gelassen oder beschädigt worden ist.

f. Wenn das Erzeugnis eine klare Änderung in der Leistung zeigt-dies weist darauf hin, daß

Wartung erforderlich ist.

21. Ersatzteile

Wenn Ersatzteile erforderlich sind, darauf achten, daß der Wartungstechniker nur die vom Hersteller

festgelegten Ersatzteile oder Teile mit den gleichen Charakteristiken wie die ursprünglichen Teile

verwendet. Unautorisierte Ersatzteile können Feuer, elektrischen Schlag oder sonstige Gefährdungen

verursachen.

22. Sicherheitsprüfung

Bitten Sie den Wartungstechniker nach der Vollendung von Wartung oder Reparaturarbeiten an diesem

Erzeugnis um die Durchführung von Sicherheitsprüfungen, um zu bestimmen, daß das Erzeugnis im

angemissenen Betriebszustand ist.

23. Anbringung an der Wand oder an der Decke

Das Erzeugnis sollte nur entsprechend den Empfehlungen des Herstellers an einer Wand oder an der

Decke angebracht werden.

24. Wärme

Das Erzeugnis sollte fern von Wärmequellen wie Radiatoren, Heizwiderständen, Öfen und anderen

Wärme erzeugenden Erzeugnissen (einschließlich Verstärkern) aufgestellt werden.

MISES EN GARDE IMPORTANTES

1. Lire les instructions

Lire toutes les instructions de sécurité et de fonctionnement avant de faire fonctionner l’appareil.

2. Conserver ces instructions

Conserver les instructions de sécurité et de fonctionnement á des fins de référence ultérieure.

3. Tenir compte des avertissements

Tous les avertissements qui figurent sur l’appareil et dans le mode d’emploi devront être respectés.

4. Observer les instructions

Observer toutes les instructions de fonctionnement et d’utilisation.

5. Nettoyage

Avant de procéder au nettoyage, débrancher l’appareil de la prise secteur. Ne pas utiliser de produits

de nettoyage liquides ou en aérosol.

Nettoyer l’appareil avec un chiffon humide.

6. Fixations

Ne pas utiliser de fixations non recommandées par le fabricant de l’appareil car elles pourraient être

source de danger.

7. Eau et humidité

Ne pas utiliser l’appareil á proximité d’eau-par exemple prés d’une baignoire, d’un lavabo, d’un évier ou

d’un bac á lessive, dans un sous-sol humide, ou prés d’une piscine, etc.

8. Accessoires

Ne pas placer l’appareil sur un chariot, un socle, un pied, un support ou one table instables L’appareil

pourrait tomber, blessant griévement des enfants ou des adultes, et étant sérieusement endommagé.

Utiliser exclusivement le chariot, le socle, le pied, le support ou la table recommandés par le fabricant,

ou vendus avec l’appareil. Pour tout montage de l’appareil, respecter les instructions du fabricant, et

utiliser á cette fin l’accessoire de montage recommandé par le fabricant.

9. L’appareil monté sur son chariot devra être déplacé avec précaution.

Des arrêts brusques, une force excessive et des surfaces irréguliéres pourraient provoquer le

renversement de l’ensemble appareil-chariot.

10. Ventilation

Les fentes et les ouvertures du coffret sont prévues pour la ventilation ainsi que pour garantir un

fonctionnement en toute sécurité de l’appareil et le protéger de toute surchauffe, et ces ouvertures ne

devront donc être ni obstruées ni recouvertes. Ne jamais obstruer les ouvertures en placant l’appareil

sur un lit, un sofa, un tapis ou toute surface similaire. Ne jamais placer l’appareil dans un support

confiné, par exemple une bibliothéque ou une é tagé re, sans ventilation suffisante ou sans repecter les

instructions du fabricant.

11. Sources d’allmentation

L’appareil devra être alimenté exclusivement sur le type d’alimentation indiqué sur l’étiquette

signalétique. Sil’on n’est pas sûr du type d’alimentatio du local, consulter le revendeur de l’appareil ou

la compagnie d’électricité locale. Pour les appareils qui fonctionnent sur batterie ou sur d’autres

sources, voir le mode d’emploi.

12. Mise á la terre ou polarisation

L’appareil est doté d’une fiche trifilaire avec mise á la terre, dont la troisiéme broche assure la mise á la

terre. Cette fiche ne rentrera que dans les prises trifilaires de mise á la terre. Ceci est une mesure de

sécurité. Si la fiche ne rentre pas dans la prise, faire remplacer la prise désuéte par un électricien.

Ne pas rendre vaine la measure de sécurité assurée par cette prise avec mise á la terre.

13. Protection du cordon d’alimentation

Acheminer les cordons d’alimentation de facon qu’on ne risque pas de marcher dessus ou de les coincer

sous un objet placé dessus ou contre eux.

Faire particuliérement attention aux fiches des cordons, á la proximité des prises, et á l’endroit oú ils

ressortent de l’appareil.

14. Foudre

Pour renforcer la protection de l’appareil pendant un orage, ou si l’on s’en éloigne ou qu’on reste

longtemps sans l’utiliser, le débrancher de la source d’alimentation. Ceci permettra d’éviter tout

dommage de l’appareil dú á la foudre et aux surtensions de ligne.

15. Surcharge

Ne pas surcharger les prises, rallonges et prises multiples car cela pourrait entraîner un risque de feu ou

de choc électrique.

16. Pénétration d’objets et de liquides

Ne jamais enfoncer d’objets d’aucune sorte dans les ouvertures de l’appareil car ils pourraient toucher

des points de tension dangereuse ou court-circuiter des piéces, ce qui pourrait provoquer un feu ou un

choc électrique. Ne jamais renverser de liquide d’aucune sorte sur l’appareil.

17. Substances inflammabes et explosives

Eviter d’utiliser l’appareil en présence de gaz, ainsi qu’á proximité immédiate de substances

inflammables et explosives.

18. Chocs ou vibrations violents

Lorsqu’on transporte l’appareil, ne pas le soumettre á des chocs ou des vibrations violents.

19. Réparations

Ne pas tenter de réparer l’aapareil soi-même car le fait d’ouvrir ou de retirer les caches risque d’exposer

l’utilisateur á des tensions dangereuses notamment. Confier toute réparation á un personnel qualifié.

20. Dommages nécessitant réparations

Débrancher l’appareil de la source d’alimentation et confier les réparations á un personnel qualifié dans

les cas suivants:

a. Lorsque le cordon d’alimentation ou sa fiche sont endommagés

b. Si du liquide s’est renversé sur l’appareil ou que des objets sont tombés dedans

c. Si l’appareil a été exposé á la pluie ou á l’eau.

d. Si l’appareil ne fonctionne pas normalement lorsqu’on observe les instructions d’utilisation.

Ne régler que les commandes couvertes par le mode d’emploi ; en effet, un réglage incorrect des autres

commandes pourrait entrainer des dommages et nécessiteront souvent des travaux de réparation

coûteux par un technicien qualifié pour remettre l’appareil en état de marche.

e. Si l’appareil est tombé ou qu’il a été endommagé.

f. Si l’appareil affiche une nette modification de ses performances, cela signifie qu’il a besoin d’être

réparé.

21. Piéces de rechange

Si l’on a besoin de piéces de rechange, veiller á ce que le technicien de réparation utilise exclusivement

les piéces de rechange spécifiées par le fabricant ou des piéces ayant les mêmes caractéristiques que les

piéces d’origine. Les piéces de rechange non autorisées risquent de provoquer un feu, un choc

électrique et autres dangers.

22. Vérificaton de sécurité

Aprés tout travail d’entretien ou de réparation de l’appareil, demander au technicien de réparation

d’effectuer les vérifications de sécurité pour s’assurer que l’appareil est en bon état de marche.

23.Montage au mur ou au plafond

L’appareil ne pourra être monté au mur ou au plafond que de la maniére recommandée par le fabricant.

24. Chaleur

Eloigner l’appareil des sources de chaleur, telles que radiateurs, appareils de chauffage, cuisiniéres, et

de tour produit engendrant de la chaleur (y compris les amplificateurs).

IMPORTANT NOTICE

For USA

These products have been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this product in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

WARNING

Changes or modifications not expressly approved by Hitachi Kokusai Electric responsible for

compliance could void the user’s authority to operate the equipment.

For Canada

This product does not exceed the class A/class B limits for radio noise emissions from digital apparatus

as set out in the radio interference regulations.

Le présent appareil n’émet pas de bruits radioélectriques dépassant les limités applicable aux appareils

numériques de classe A prescrites dans le rVglement sur le brouillage radioélectrique édicter par le

ministére des communications du canada.

Contents

Outline and features................................................................................................................................................1

Warnings and cautions when using ........................................................................................................................2

Facility names and functions...................................................................................................................................3

Filter selection .........................................................................................................................................................4

White and black balance adjustment ......................................................................................................................8

Electronic shutter setting.......................................................................................................................................13

Function menu.......................................................................................................................................................14

Specifications ........................................................................................................................................................33

Service information................................................................................................................................................35

Outline and features

The DK-H100 is a high-performance special

application HDTV/SD camera.

The camera is ideal for graphic stands point of view

and remote observation applications.

With its 2.3million pixels 3-CCD, the DK-H100

provides outstanding performance. The camera offers

sharper and cleaner HD images due to its 14-bit A/D

converters and Hitachi’s implementation of the latest

digital processing technology. The camera achieves

outstanding high sensitivity and a low vertical smear

specifications.

Outstanding Features



High resolution

The latest generation 2/3-inch 2.3 million pixels

CCD with micro lenses and digital multi speed

signal processing circuits provide a horizontal

resolution performance of 1100 TV lines

(luminance channel).



Latest generation Digital technology

The brand new, power efficient Digital Signal

Processor LSI with 65nm design rule and 14-bit

analog-to-digital conversion provide very faithful

video image reproduction and quality.

Digital video processing and encoding provide low

interference and high stability.



High sensitivity and Signal to Noise ratio

Low-noise circuit technology provide a signal to

noise ratio of 58dB.

Even at high gain, clear images are obtained

with little noise.

The standard sensitivity is F10 at 2000lx and

minimum illumination is 0.002lx with F1.4 lens

iris stop.



Versatile CCD drive functions

Four modes of shutter operation are provided:

Five PRESET electronic shutter speeds

LOCK SCAN to image computer monitors

without flicker

Automatic Electronic Shutter (AES) maintains

the video level with a fixed lens F-stop.

Charge Controlled Frame (CC FRM) offers

improved vertical resolution.



Digital processing improves Image Highlight

Quality

Knee saturation and auto-knee

The auto knee provides a wide dynamic range

by dynamically compressing the video level

above 100

％

. Knee saturation restores color

saturation to scene highlights above 100

％

Automatic Skin Tone Detail Circuits

Skin tone detail smoothes and softens facial

lines and blemishes without sacrificing overall

scene detail, also provides two separate

settings that can be used separately or

simultaneously.

Automatic Skin tone detail provides an easy

and fast means to optimize Skin tone detail.

Variable Detail Boost Frequency

The detail frequency can be adjusted to

provide coarse or fine contours around edges of

subjects in the scene thereby reproducing a

natural and pleasing picture.

y12-Vector and Linear Matrix masking

The 12-vector and linear matrix provide the

user a wide latitude in subject image color

control.

Skin Tone masking

Skin tone masking provides “fine” “Painting”

(hue and saturation) of Skin tones without

effecting other colors in the scene.

Gray Scale Automatic Setup

This “through the lens” automatic setup is

uses a standard gray scale chart to

automatically setup gain, gamma, black and

flare thus saving the video operator time and

effort.

Automatic Shading

Automatic shading corrects white vertical

shading at the push of a button.

This function provides separate memory of

lens’ modulation shading characteristics to

optimize the X1 and X2 lens extender

positions.



Extensive User-Friendly

yScene Files

Gain, detail, masking, gamma and other settings

can be stored in eight scene file memories.



Viewfinder displays

Two mode zebra

Menu selection of over-level or between range

zebra is provided.

ySafety zone and center mark display

Warnings and cautions when using

Viewfinder high voltage

yDo not open the viewfinder cover. There is

danger of touching internal high voltage

components.

Power supply

The specified power supply input voltage of this

camera is 12VDC. Be sure to use the designated

power supply.

Do not disassemble or modify

The camera contains precision internal

components. Do not open the cover or disturb

switches and controls other than designated.

There is risk of impaired performance and

damage.

Keep foreign object out of interior

Entry of water, metallic or other foreign materials

can cause failure and damage.

Select use and storage locations carefully

Avoid using or storing the equipment in the

following types of locations. Impaired

performance and damage can be caused.

yExtremely hot or cold locations (exceeding -10 to

45°C), such as in enclosed vehicles.

ySubject to strong vibration.

yHumid or dusty locations.

ySalt spray or corrosive gases.

yStrong electromagnetic fields (e.g., near TV or

radio transmitters).

yWhere exposed to rain.

Do not cover or otherwise obstruct camera heat

dissipation during operation.

When connecting and disconnecting lens,

microphone and other cables, grasp the connector

by the body, not the attached cable. Cables can be

damaged by pulling on them.

Note when transporting

When transporting by hand, use the carrying

case. If shipping by truck or other means, pack

in the carrying case, then use further cushioning

and pack in a sturdy carton.

Cleaning

Use a photographers air blower to clear dust from

the lens and filters. Wipe the case with a soft

dry cloth. Do not use volatile solvents, as these

may deform the materials.

In event of difficulty

Disconnect from power and contact the nearest

Hitachi Kokusai Electric service agency.

**********CCD characteristic phenomena**********

The following types of phenomena are innate characteristics of a charge coupled device (CCD) and are

not malfunctions. Be aware of these when using a CCD camera for broadcast or other demanding

applications.

Smear

When a bright object is picked up, thin trails appear above and below the

image.

The effect is more pronounced at high electronic shutter speeds.

Fixed pattern

When operate at high temperature, a fixed pattern (vertical stripes,

white dots) can appear. The pattern is more easily seen when the

camera sensitivity is raised.

NOTE

Facility names and functions

5 6 7 8

1. Lens mount

Bayonet type lens mount.

2. SDI OUT connector

HD-SDI/SD-SDI signal output.

3. MON OUT connector

HD-SDI/SD-SDI signal output with character.

4. GL IN connector

External sync signal input

(Tri-level sync or Black burst)

5. DC IN connector

12V DC is supplied.

6. POWER LED

Off: Camera power not supplied.

Lights (green): Camera power on.

7. REMOTE1 connector

Connection for remote control unit or personal

computer.

8. LENS connector

Connection for lens plug.

9. FILTER button

It combines with the L/R button, and the ND

filter is controlled.

It combines with the U/D button, and the ECC

filter is controlled.

10. D button

Menu mode:The menu cursor moves down.

Direct mode:Color bar signal output.

11. R button

Menu mode:Change the menu data.

Direct mode:Hold the button depressed for longer

than 2 seconds for automatic black

balance(ABB) adjustment.

12. U button

Menu mode:The menu cursor moves up.

Direct mode:Not used

13. L button

Menu mode:Change the menu data.

Direct mode:Hold the button depressed for longer

than 2 seconds for automatic white

balance(AWB) adjustment.

14. MENU button

The function menu is displayed.

15. VF OUT connector

Connection for viewfinder.

16. REMOTE2 connector

Connection for remote control unit.

Lens installation

Install according to the following procedure.

1. Raise the lens lever and remove the mount cap.

3. Lower the lens lever to secure the lens.

2. Align the lens center mark with the indent at the

upper part of the lens mount and install the lens.

4. Engage the cable with the cable clamp and

connect it to the lens connector.

Notes

The following adjustments may be required according to the type of lens.

1. Lens flangeback, 2. Lens white shading.

3. Lens auto iris speed, 4. Lens iris close limit. (AUTO IRIS menu)

Lens flangeback adjustment

When operating a zoom lens, if the focus is not precisely aligned at both the telephoto and wide angle

extremes of the lens, the flangeback (distance from the lens mounting plane to the focal plane) is adjusted.

This adjustment is generally required only once unless the lens is replaced.

Adjustment

1. Set the lens iris for manual operation.

2. Set a flangeback adjusting chart about 3 meters distant.

3. Open the iris and adjust the lighting to obtain the correct video output level.

If the video level is too high, use a ND filter or electronic shutter.

4. Loosen the FB ring setscrew.

5. By hand or motor, set the zoom ring to the telephoto position.

6. Observe the flangeback chart image and turn the distance ring to adjust the focus.

7. Set the zoom ring to the wide angle position.

8. Turn the FB ring and adjust the focus. Use care not to turn the distance ring.

9. Repeat this process until focus is obtained at both telephoto and wide angle settings.

10. Securely tighten the FB ring setscrew.

･Also, see the lens operating instructions.

White shading adjustment

White shading adjustment is recommended after replacing the lens.

The adjustment relates to the camera vertical coloration. If the lens includes an extender, the shading can

be optimized for both extender on and off modes.

(Vertical coloration refers to an effect whereby the image of an overall white sheet of paper tends toward

green at the top and magenta at the bottom, or vice versa.)

Adjustment

1. Install the lens on the camera.

Be sure to connect the lens cable.

2. Set the electronic shutter to off and the gain to L (0 dB).

3. Set the lens extender to off.

4. When notice flicker on the monitor which occurred by fluorescent or mercury lighting,

use sunlight or halogen as the light source.

Using auto iris mode for the lens iris, the iris stop should be between F4 and F11. If necessary, adjust

the light source level and keep iris stop position in it (be sure the electronic shutter is off).

5. Open the WHITE SHADING sub menu from MAINTENANCE menu.

6. Shift cursor to WHT SHADING : PUSH > 1 SEC.

7. Hold the R button for about 1 second to adjust white shading. The screen top and bottom cursors

flash to indicate automatic white shading adjustment in progress. The cursors extinguish at the end of

adjustment.

8. Set the extender (if provided) to on and repeat the above step.

9. Close the Function menu.

White shading adjustment is completed by the above. The adjustment is stored in a nonvolatile memory

and ordinarily does not need to be repeated even if the power is switched off.

Notes

1. Precise adjustment may not be obtainable with some special lenses.

2. Even after adjustment, some coloration may occur near the open iris setting. This is due to

lens and optical system characteristics and is not a malfunction.

■ＷＨＴ　ＳＨＡＤＩＮＧ

　ＥＸＴＥＮＤＥＲ　　　：ＯＦＦ（Ｘ１）

　ＷＨＴ　ＳＨＡＤＩＮＧ：ＰＵＳＨ　＞　１ＳＥＣ

　Ｒ　Ｖ　ＳＡＷ　　　　：　　　０

　Ｇ　Ｖ　ＳＡＷ　　　　：　　　０

　Ｂ　Ｖ　ＳＡＷ　　　　：　　　０

　ＩＮＩＴＩＡＬＩＺＥ　：

Cursors

Filter selection

Filter setting

In order to obtaining correct white balance, the sufficient optical filter selection is required accordance

with the scene lighting source. The correct optical filter according to the scene light source needs to be

selected in order to obtain correct white balance.

Operation method

Set the FILTER button and the L/R button.

ND Filter

Filter No. ND Filter

1 Clear

2 1/4ND

3 1/16ND

4 1/64ND

Set the FILTER button and the L/R button.

ECC Filter

Filter No. ECC Filter

A 3,200K

B 4,300K

C 5,600K

D 6,300K

E 8,000K

FILTER button + L/R button

Clear ⇔ 1/4 ND ⇔ 1/16 ND ⇔ 1/64 ND

FILTER button + U/D button

3200K ⇔ 4300K ⇔ 5600K ⇔ 6300K ⇔ 8000K

White and black balance adjustment

White balance adjustment

White balance will be adjusted to the best effort in the sequence of AWB (auto white balance), ABB (auto

black balance), and again AWB.

Readjustment is normally not required even at power off/on.

Be sure to adjust the white balance after changes in the lighting conditions.

White and black balance adjustment progress can be observed from the screen.

Adjustment

1. Set the W.BAL MODE in the WHITE GAIN menu to MEMORY.

2. Set the FILTER with lighting condition accordingly.

See Optical filter selection in page 7.

3. Place a white pattern at a location subject to the

same lighting conditions as the scene. Use zoom

function of the lens so that the screen is white.

A white object (e.g., cloth, wall) placed near the scene

of interest can be used provided the size is adequate

(see figure).

4. Adjust the lens iris.

5. Hold the L button depressed for two second. White

balance is adjusted automatically.

6. During adjustment, the following messages appear on the screen.

7. Adjustment is completed in several seconds.

Adjustment in progress Adjustment complete

White

cloth

Note

Use care a high luminosity

light source, such as a

spotlight, does not enter the

screen area.

t least 1/5 the screen hei

t least 1/5 the screen width

La page charge ...

Hitachi DK-H100 Operating Instructions Manual

Marque: Hitachi

Modèle: DK-H100

Taper: Operating Instructions Manual

Ce manuel convient également à

DK-Z50

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi DK-H100

Hitachi DK-H100 Operating Instructions Manual

Ce manuel convient également à

Hitachi DK-H100 Operating Instructions Manual

dans d''autres langues

Documents connexes

Autres documents