Philips DDRC420FR Relay Controller Manuel utilisateur

Marque: Philips

Modèle: DDRC420FR Relay Controller

Taper: Manuel utilisateur

DDRC420FR

RJ12

x 2

108 mm (4.25 in)

95 mm (3.74 in)

105 mm (4.13 in)

64 mm (2.52 in)

68 mm (2.68 in)

1 A 45 mm

(1.77 in)

45 mm

(1.77 in)

Relay Controller

Installation Instructions

Instructions d’installation

Installationsanweisungen

Instrucciones de instalación

Istruzioni per l’installazione

Installatie-instructies

インストール手順

安装指示

≤

90%

IEC Pollution Degree II

Devices must be installed in an

approved enclosure by a qualied

electrician in accordance with all

national and local electrical and

construction codes and regulations.

Les appareils doivent être installés dans un lieu jugé

apte, par un électricien qualié et conformément

aux règles et normes locales et nationales en

matière d’électricité et de construction.

Die Geräte müssen von einem geprüften Elektriker

entsprechend allen nationalen und lokalen Elektro

– und Bauvorschriften in einem zugelassenen

Gehäuse installiert werden.

Los dispositivos se deben instalar en un recinto

aprobado por un electricista cualicado de

acuerdo a todos los reglamentos eléctricos y de

construcción locales y nacionales pertinentes

I dispositivi devono essere installati da un

elettricista qualicato in un luogo approvato, in

conformità a tutti gli standard e le norme nazionali

e locali vigenti in materia di impianti elettrici e

costruzioni edilizie.

Apparaten moeten door een erkende elektricien

worden geïnstalleerd in een goedgekeurde

behuizing in overeenstemming met alle nationale

en lokale elektriciteits – en bouwvoorschriften

en wetgeving.

デバイスを取り付ける際は、資格のある電気技師に依頼

し、電気と建設に関する国および地域のすべての法令に

従って、認可されている筐体内に取り付けてください。

根据国家/地区及当地的电气与建筑规范和法规，该设

备必须由有资质的电工安装在经批准的外罩内。

50° C (122° F)

0° C (32° F)

20A 20A 20A 20A

0.62 Nm

5.5 Lb-in

≤ 5 mm2

10+ AWG

1 2 3 4

LIN IN IN INOUT OUT OUT OUT

CH1 CH2 CH3 CH4

SUPPLY

Not

Connected

OFF

Installation example

Exemple d'installation

Installationsbeispiel

Ejemplo de instalación

Esempio di installazione

Installatievoorbeeld

安装示例

1 / 3

CH-CH ≤ 300 V (UL) / 400 V (CE)

20A 20A

NL1 L2

277/480 V

1 2 3 4

OFF

N L

IN IN IN INOUT OUT OUT OUT

CH1 CH2 CH3 CH4

SUPPLY

Not

Connected

CH-CH = 277 / 480 V

Installation example

Exemple d'installation

Installationsbeispiel

Ejemplo de instalación

Esempio di installazione

Installatievoorbeeld

安装示例

0.62 Nm

5.5 Lb-in

≤ 5 mm2

10+ AWG

2 A

2 B

68 mm (2.68 in)

oset 8 mm (0.31 in)

Output Ratings/Channel (CH)

General Use

Load Type CH1-CH4

16 A, 277 V

16 FLA (1 HP), 120 V

14.5 FLA (2 1/

HP), 240 V

14.1 FLA (3 HP), 277 V

500 A

Incandescent

Standard Driver

Electronic Driver

Inrush Current

Motor

CH-CH ≤ 300 V (UL) / 400 V (CE)

DDRC420FR ≤ 64 A (UL), 80 A (CE)

Output Ratings/Group

16 A, 277 V (UL)

20 A, 240 V (CE)

1 2 3 4

IN IN IN INOUT OUT OUT OUT

CH1

OFF

CH2 CH3 CH4

SUPPLY

Not

Connected

OFF

RS-485 DyNet

GND AUX/UL924

< 20 m

0.4 Nm

3.5 Lb-in

0.3-2.5mm2

22-12 AWG

≤ 2 A

SHLD

GND

D+

D-

+12 V

AUX/

UL924

RS-485 DyNet

100-240 V

0.25 A

CH1 CH2 CH3 CH4

RJ12

RS-485 DyNet/DMX Rx

+12 V

D +

D -

GND

SHLD

AUX/

UL924

IN OUT IN OUT IN OUT IN OUT

µP

12 V 200 mA

SELV/Class 2 (UL)

IEC Overvoltage Category III

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice – This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged

to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the

equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an

experienced radio/TV technician for help. Any modications not approved by the manufacturer of this device could void the user’s authority to operate this device.

This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B). Cet appareil numerique de la classe B est conforme a la norme NMB-

003 du Canada: CAN ICES-3(B)/NMB-3(B).

Installation of a home and building automation and control system shall comply with IEC 60364 (all parts). The temperature limits and current-carrying capacities

for the communication wires specied in IEC 60364-5-52 shall not be exceeded.

AZZ 377 0123 R22

change without notice. No representation or warranty as to the accuracy or

completeness of the information included herein is given and any liability

for any action in reliance thereon is disclaimed. Philips and the Philips

Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other

trademarks are owned by Signify Holding or their respective owners.

www.dynalite.com