Samsung LN-S5296D Le manuel du propriétaire

Catégorie
Téléviseurs LCD
Taper
Le manuel du propriétaire
Owner’s
Instructions
Register your product at
www.samsung.com/global/register
LN-S4096D
LN-S4696D
LN-S5296D
TFT-LCD TELEVISION
BN68-01047X-00
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
Comment contacter Samsung dans le monde
Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service
Consommateurs Samsung.
Contacte con SAMSUNG WORLD-WIDE
Si tiene alguna pregunta o comentario referente a nuestros productos, por favor contacte con nuestro Servicio de
Atención al Cliente.
Country
CANADA
U.S.A
Customer Care Center
1-800-SAMSUNG (7267864)
1-800-SAMSUNG (7267864)
Address
Samsung Electronics Canada Inc., Customer Service
55 Standish Court Mississauga, Ontario L5R 4B2
Canada
Samsung Electronique Canada Inc., Service
á
la Client
é
le
55 Standish Court Mississauga, Ontario L5R 4B2
Canada
Samsung Electronics America, Inc.
105 Challenger Road
Ridgefield Park, NJ 07660-0511
Web Site
www.samsung.com/ca
www.samsung.com
BN68-01047X-00Cover.qxd 8/29/06 10:38 AM Page 1
Precautions When Displaying a Still Image
A still image may cause permanent damage to the TV screen.
Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention.
This image retention is also known as "screen burn".
To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and center of the screen
caused by the difference of light emission on the screen.
Playing a DVD or a game console may cause a similar effect to the screen.
Damages caused by the above effect are not covered by the Warranty.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
Précautions à prendre lors de l'affichage d'une image fixe
Une image fixe peut causer des dommages irrémédiables à l'écran du téléviseur.
N'affichez pas une image fixe sur l'écran LCD plus de 2 heures. Cela pourrait provoquer une rémanence de l'image à l'écran.
Cette rémanence de l'image est également appelée "brûlure de l'écran".
Pour éviter une telle rémanence de l'image à l'écran, réduisez la luminosité et le contraste de l'écran lorsque vous laissez une image fixe affichée.
Regarder l'écran LCD du téléviseur en format 4:3 pendant une longue période peut laisser des traces de bordures à gauche,
à droite et au centre de l'écran, à cause de la différence d'émission de lumière sur l'écran.
La lecture d'un DVD ou l'utilisation d'une console de jeu peut avoir un effet similaire sur l'écran.
Les dommages provoqués par les effets qui précèdent ne sont pas couverts par la garantie.
L'affichage d'images fixes de jeux vidéo et d'ordinateurs pendant plus longtemps qu'une période spécifique peut provoquer des rémanences.
Pour éviter cela, réduisez la "luminosité" et le "contraste" lors de l'affichage d'images fixes.
Precauciones al mostrar en la pantalla una imagen fija
La imagen fija puede causar daños permanentes en la pantalla del televisor.
No deje una imagen fija en la pantalla LCD durante más de dos horas ya que se podría producir una retención de la imagen en la pantalla. Este fenómeno de
retención de imágenes también se denomina "quemadura de pantalla".
Para evitar que se produzca esa persistencia de la imagen, reduzca el nivel de luminosidad y de contraste de la pantalla cuando muestre imágenes fijas.
El uso del televisor LCD en formato 4:3 durante un tiempo prolongado puede dejar rastros de bordes en las partes izquierda,
derecha y central de la pantalla debido a las diferencias en la emisión lumínica de la pantalla.
La reproducción de un DVD o el uso de una consola de videojuegos pueden provocar un efecto similar en la pantalla.
Reproducir un DVD o una videoconsola puede causar un efecto similar en la pantalla. La garantía no cubre estos daños.
Ver imágenes fijas de videojuegos y PC durante más tiempo del indicado puede producir restos de imágenes parciales.
Para evitar este efecto, reduzca el 'brillo' y el 'contraste' cuando vea imágenes fijas.
© 2006 Samsung Electronics Co., Ltd. All rights reserved.
Still 8/29/06 10:38 AM Page 1
Symbol Press Note
Contents
GENERAL INFORMATION
List of Features .................................................................................. 3
Accessories........................................................................................ 3
Viewing the Control Panel.................................................................. 4
Viewing the Connection Panel........................................................... 5
Remote Control .................................................................................. 7
Installing Batteries in the Remote Control ......................................... 8
CONNECTIONS
Connecting VHF and UHF Antennas................................................. 8
Connecting Cable TV ......................................................................... 9
Connecting a VCR ............................................................................. 10
Connecting an S-VHS VCR ............................................................... 10
Connecting a Camcorder................................................................... 11
Connecting a DVD Player/Set-Top Box ............................................. 11
Connecting a DVD Player/Set-Top Box via DVI ................................ 12
Connecting a DVD Player/Set-Top Box via HDMI ............................. 12
Connecting a Digital Audio System.................................................... 13
Connecting an Amplifier/DVD Home Theater .................................... 13
Connecting CableCARD .................................................................... 14
Connecting a PC................................................................................ 14
OPERATION
Turning the TV On and Off................................................................. 15
Plug & Play Feature........................................................................... 15
Dynamic Menus and On-Screen Displays......................................... 17
Navigating Menus by Using the Menu Map....................................... 18
Selecting a Menu Language .............................................................. 19
Memorizing Channels ........................................................................ 20
Changing Channels ........................................................................... 22
Setting Up Your Remote Control ...................................................... 23
Remote Control Codes ...................................................................... 25
Setting the Clock................................................................................ 28
Setting the On/Off Timer .................................................................... 30
Setting the Sleep Timer...................................................................... 31
Viewing an External Signal Source.................................................... 32
Assigning Names to External Input Mode ......................................... 33
CHANNEL CONTROL
Selecting Your Favorite Channels ................................................ 34
Viewing the Channel Lists ............................................................ 35
Adding and Erasing Channels...................................................... 36
Labeling the Channels.................................................................. 37
Fine Tuning Analog Channels Analog ........................................ 38
Checking the Digital-Signal Strength Digital .............................. 39
LNA (Low Noise Amplifier)............................................................ 39
PICTURE CONTROL
Picture Control .............................................................................. 40
Customizing the Picture Settings ................................................ 41
Changing the Picture Size............................................................ 43
Using the Color Weakness Enhancement Feature ..................... 44
Digital Noise Reduction ................................................................ 45
DNIe (Digital Natural Image engine) ............................................ 46
Setting the Film Mode................................................................... 47
Viewing Picture-In-Picture ............................................................ 48
Changing the Size of the Sub (PIP) Picture................................. 49
Changing the Location of the Sub (PIP) Picture .......................... 49
Selecting a Signal Source (Air or Cable) for PIP ......................... 50
Changing the Channel of the Sub (PIP) Picture .......................... 50
Freezing the Picture ..................................................................... 51
Setting the Blue Screen Mode...................................................... 51
SOUND CONTROL
Sound Control............................................................................... 52
Customizing the Sound ................................................................ 53
Setting the SRS TruSurround XT ................................................ 54
Auto Volume ................................................................................. 55
Choosing a Multi-Channel Sound (MTS) track Digital ............... 56
Choosing a Multi-Channel Sound (MTS) track Analog .............. 57
Selecting the Internal Mute........................................................... 58
Selecting the Sound Select .......................................................... 59
Setting the On/Off Melody ............................................................ 60
SPECIAL FEATURES
Setting the Function Help ............................................................. 61
Using the Energy Saving Feature ................................................ 62
Menu Transparency Level ............................................................ 62
Using Game Mode............................................................................. 63
Using the V-Chip........................................................................... 64
How to Enable/Disable the Rating Controls ................................. 65
How to Set up Restrictions Using “TV Parental Guidelines” ........ 66
How to Set up Restrictions Using “MPAA Rating”........................ 67
Important Notes About Parental Locks......................................... 68
How to Set up Restrictions Using Canadian English ................... 69
How to Set up Restrictions Using Canadian French.................... 70
Using the V-Chip for Digital channels........................................... 71
Viewing Closed Captions (On-Screen Text Messages) Analog .. 72
Viewing Closed Captions (On-Screen Text Messages) Digital .. 73
Setting the Blue Eye..................................................................... 75
Using the CableCARD.................................................................. 76
Using the CableCARD Setup Function ........................................ 76
Channel List Reorganization ........................................................ 77
English-1
English
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 1
Contents
English-2
Symbol Press Note
WISELINK
Using the WISELINK Function........................................................... 78
Using the WISELINK Menu................................................................ 79
Using the PHOTO (JPEG) List .......................................................... 80
Using the MP3 List............................................................................. 87
Using the Setup Menu ....................................................................... 89
USING D-NET
What’s D-Net?.................................................................................... 91
When Connecting D-Net (IEEE1394) Compatible devices................ 92
Connection Options............................................................................ 93
4-Pin and 6-Pin Connectors............................................................... 94
Selecting a D-Net device ................................................................... 95
The Direct Device-To-Device Option.................................................. 96
The D-Net control panel..................................................................... 97
Control Panel Images for Each Device
......................................... 99
Operating Tips.................................................................................... 100
Recording Tips ................................................................................... 102
Tips on stopping recording................................................................. 103
File List............................................................................................... 104
Troubleshooting (D-Net)..................................................................... 106
PC DISPLAY
Using Your TV as a Computer (PC) Display ................................ 110
Setting Up Your PC Software (Windows Only)............................. 111
Display Modes ............................................................................. 111
Adjusting the Picture Quality ........................................................ 112
Changing the Picture Position ...................................................... 113
Adjusting the Picture Quality and Position Automatically............. 114
Changing the Picture Size (PC Mode) ......................................... 115
Viewing the Current Resolution.................................................... 116
Initializing the Picture Settings...................................................... 117
APPENDIX
Identifying Problems .................................................................... 118
Installing the Stand....................................................................... 119
Disconnecting the Stand............................................................... 119
Stand Swivel Function ................................................................. 119
Installing the Wall Mount Kit (LN-S4096D)................................... 120
Installing the Wall Mount Kit (LN-S4696D/LN-S5296D ).............. 121
Using the Anti-Theft Kensington Lock ......................................... 123
Specifications ............................................................................... 123
Dimensions (LN-S4096D)............................................................. 124
Dimensions (LN-S4696D)............................................................. 125
Dimensions (LN-S5296D)............................................................. 126
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 2
English-3
List of Features
Easy-to-operate remote control
Navigating Menus by Using the Menu Map
Automatic timer to turn the TV on and off at any time you choose
Adjustable picture and sound settings and the ability to memorize your favorite settings
Automatic channel tuning for up to 181 channels
A special filter to reduce or eliminate reception problems
Fine tuning control for the sharpest picture possible
A built-in multi-channel sound decoder for stereo and bilingual listening
Built-in, dual channel speakers
A special sleep timer
Picture-in-Picture capability that lets you watch two channels at once
Widescreen TV with adjustable image size
Life-like clear images provided by DNle technology
Color Weakness mode
Digital Input jack
CableCARD slot
D-Net (IEEE1394)
Digital Input (HDMI/DVI IN) jack
Digital Audio Output (OPTICAL) jack
Game mode
Easy-to-use channel manager menu.
WISELINK enables you to view and play photo (JPEG) and audio files (MP3) through the TV’s WISELINK jack.
Accessories
Please make sure the following items are included with your LCD TV.
If any items are missing, contact your dealer.
General Information
Remote Control & Batteries (AAA x 2)
(BN59-00529A)
Power Cord
(3903-000144)
Cleaning Cloth
(BN63-01798A)
Cover-Bottom
LN-S4096D (BN63-02491A)
LN-S4696D (BN63-02624A)
LN-S5296D (BN63-02624A)
Owners Instructions Warranty Card / Registration
Card / Safety Guide Manual
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 3
English-4
Viewing the Control Panel
SOURCE
Toggles between all the available input sources
(TV, AV1, AV2, S-Video, Component1, Component2,
PC, HDMI1, HDMI2).
In the on-screen menu, use this button as you would
use the ENTER button on the remote control.
MENU
Press to see an on-screen menu of your TV’s features.
Press to increase or decrease the volume.
In the on-screen menu, use the buttons as you
would use the and buttons on the remote control.
Press to change channels.
In the on-screen menu, use the buttons as you
would use the
and buttons on the remote control.
SPEAKERS
(POWER)
Press to turn the TV on and off.
POWER INDICATOR
Blinks and turns off when the power is on and lights up
in stand-by mode.
REMOTE CONTROL SENSOR
Aim the remote control towards this spot on the TV.
Buttons on the Lower-Right Part of the Panel
The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.
To use the more advanced features, you must use the remote control.
The product color and shape may vary depending on the model.
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 4
English-5
Rear Panel Jacks
Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players.
For more information on connecting equipment, see pages 8-14.
Viewing the Connection Panel
COMPONENT IN 1,2
Connect Component video/audio.
HDMI/DVI IN 1,2 / DVI IN (R-AUDIO-L)
Connect to the HDMI jack of a device with an HDMI output.
Use the HDMI/DVI terminal for DVI connection to an external
device with a DVI output. You should use a DVI to HDMI
cable or DVI-HDMI adapter (DVI to HDMI) for video
connection, and the DVI-IN ‘R-AUDIO-L’ terminal for audio.
- HDMI/DVI IN terminal does not support PC.
- No sound connection is needed for an HDMI to HDMI
connection. Sound connection is only needed for
HDMI to DVI.
DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio component.
D-NET (IEEE1394) S400MPEG
Connect to external IEEE1394 digital products such
as digital VCRs and camcorders. Two jacks are provided
for this purpose, which allow for a high degree of
flexibility for connecting your D-Net controlled system.
(Refer to page 91~105)
AV IN 1
Video and audio inputs for external devices, such as a
camcorder or VCR.
S-VIDEO
Connect an S-Video signal from a camcorder or VCR.
ANT 1 IN (AIR)/ANT 2 IN (CABLE)
Connect to an antenna or cable TV system.
SERVICE
Connectors for service only.
AV OUT
Connect to the audio input jacks on your Amplifier/
Home theater. Use the video out to connect another
monitor
PC IN
Connect to the video and audio output jacks on your PC.
POWER INPUT
Connect the supplied power cord.
KENSINGTON LOCK
The Kensington lock (optional) is a device used to
physically fix the system when used in a public place.
If you want to use a locking device, contact the dealer
where you purchased the TV.
CableCARD
TM
Insert a CableCARD into the slot. (Refer to page 14)
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 5
English-6
WISELINK
Connect an USB mass storage device to view photo files(JPEG) and play audio files (MP3).
VIDEO, (R-AUDIO-L)
Video and audio inputs for external devices, such as a camcorder or VCR.
Headphone
Connect a set of external headphones for private listening.
Side Panel Jacks
Use the left side panel jacks to connect a component that is used only occasionally, such as a camcorder or video game. (See page 11)
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 6
English-7
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly at the TV.
You can also use your remote control to operate your VCR, Cable box, DVD player, or Set-Top Box.
POWER
Turns the TV on and off.
NUMERIC BUTTONS
Press to change the channel.
Press to select additional channels
(digital and analog) being broadcast by
the same station. For example, to
select channel “54-3”, press “54”, then
press “
” and “3”.
CH MGR
Used to display Channel Lists on the
screen.
ANTENNA
Press to select “AIR” or “CABLE”.
VCR/DVD Functions
- Rewind
- Stop
- Play/Pause
- Fast/Forward
VOL / VOL
Press to increase or decrease the
volume.
(
MUTE)
Press to temporarily cut off the sound.
MENU
Displays the main on-screen menu.
S.MODE
Sound mode selection.
PIP
Picture-in Picture ON/OFF.
P.MODE
Picture effect selection.
SRS
Selects SRS TruSurround XT mode.
MTS
Press to choose stereo, mono or
Separate Audio Program
(SAP broadcast).
CAPTION
Controls the caption decoder.
SLEEP
Press to select a preset time interval
for automatic shut off.
SET
Sets the remote to control your
TV, VCR, Cable, DVD, or Set-Top Box
TV, DVD, STB, CABLE, VCR
Press to operate your TV,
DVD, STB, CABLE (box), or VCR
When pressing this button, a number
of buttons on the remote control (e.g.
TV, DVD, STB, CABLE, VCR, MUTE,
VOL and CH buttons) light up for a few
seconds and then turn off to save
power. This function is convenient for
using the remote at night or when dark.
SOURCE
Press to display all of the available
video sources.
PRE-CH
Tunes to the previous channel.
FAV.CH
Press to switch to your favorite channels.
WISELINK
This function enables you to view and play
photo (JPEG) and audio files (MP3) from
an external device. (Refer to page 79)
CH / CH
Press to change channels.
EXIT
Press to exit the menu.
UP / DOWN / LEFT /
RIGHT / ENTER
Use to select on-screen menu items
and change menu values.
INFO
Press to display information on the TV
screen.
D-Net
Runs the D-Net view function.
(Refer to pages 91~105)
STILL
Press to stop the action during a
particular scene.
Press again to resume normal video.
P.SIZE
Picture size selection.
E.SAVING
Adjusts screen brightness to save energy.
CH
Displays the available channels in
sequence. (These buttons change
channels in the PIP window only.)
ADD/DEL
Use to store and delete channels
to/from memory.
RESET
When your remote does not work,
change the batteries and press the
RESET button for 2-3 seconds
before use.
This is a special remote control for the visually
impaired, and has Braille points on the Power,
Channel, Volume, Stop and Play/Pause buttons.
The performance of the remote control may be
affected by bright light.
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 7
English-8
1. Place the wires from the twin leads under the screws on a 300-75
adapter
(not supplied).
Use a screwdriver to tighten the screws.
2. Plug the adaptor into the ANT 2 IN (CABLE) terminal on the back of the TV.
Connecting VHF and UHF Antennas
If your antenna has a set of leads that look like this, see “Antennas with 300
Flat Twin Leads”
below.
If your antenna has one lead that looks like this, see “Antennas with 75
Round Leads”.
If you have two antennas, see “Separate VHF and UHF Antennas”.
Antennas with 300 Flat Twin Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300
twin flat leads, follow the directions below.
1. Plug the antenna lead into the ANT 1 IN (AIR) terminal on the back of the TV.
Antennas with 75 Round Leads
1. Connect both antenna leads to the combiner.
2. Plug the combiner into the ANT 1 IN (AIR) terminal on the bottom of the rear panel.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting
the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).
UHF
VHF
ANT 1 IN
(AIR)
ANT 2 IN
(CABLE)
ANT 1 IN
(AIR)
1. Lift the cover at the back of the remote control upward as shown in the figure.
2. Install two AAA size batteries.
Make sure to match the “+” and “–” ends of the batteries with the diagram inside the
compartment.
3. Replace the cover.
Remove the batteries and store them in a cool, dry place if you won’t be using the remote
control for a long time.
The remote control can be used up to about 23 feet from the TV.
(Assuming typical TV usage, the batteries last for about one year.)
If the remote control doesn’t work, check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage, or is the power cord unplugged?
5. Is there a special fluorescent light or neon sign nearby?
Installing Batteries in the Remote Control
UHF
VHF
Connections
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 8
English-9
After you have made this connection, set the A/B Switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled
channels. (When you set the A/B Switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)
2. Connect this cable to a two-way splitter.
Splitter
Incoming
cable
3.
Connect an RF cable between an OUTPUT
terminal on the splitter and the IN terminal
on the cable box.
Splitter
Cable Box
Incoming
cable
4. Connect an RF cable between the
ANT OUT terminal on the cable box and
the B–IN terminal on the RF(A/B) Switch.
Splitter
Cable Box
RF (A/B)
Switch
Incoming
cable
5. Connect another cable between the other
OUT terminal on the splitter and the A–IN
terminal on the RF (A/B) Switch.
Splitter
Cable Box
Incoming
cable
6. Connect the last RF cable between the
OUT terminal on the RF (A/B) switch and
the ANT 2 IN (CABLE) terminal on the rear
of the TV.
Splitter
Cable Box
Incoming
cable
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way
splitter, an RF (A/B) switch, and four lengths of RF cable. (These items are available at most electronics stores.)
1. Find and disconnect the cable that is
connected to the ANT IN terminal on your
cable box.
This terminal might be labeled “ANT IN”,
“VHF IN” or simply, “IN”.
ANT IN
RF (A/B)
Switch
TV Rear
RF (A/B)
Switch
ANT 2 IN
(CABLE)
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
1. Plug the incoming cable into the ANT 2 IN (CABLE) terminal on the back of the TV.
Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.
2.
Connect the other end of this cable to the ANT 2 IN (CABLE) terminal on the back of the TV.
Connecting to a Cable Box that Descrambles All Channels
1. Find the cable that is connected to the ANT OUT terminal on your cable box.
This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.
ANT OUT
ANT IN
ANT 2 IN
(CABLE)
ANT 2 IN
(CABLE)
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 9
English-10
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions
on pages 8-9). Skip step 1 if you have not yet connected to an antenna or a cable system.
1. Unplug the cable or
antenna from the back
of the TV.
2. Connect the cable or
antenna to the ANT IN
terminal on the back
of the VCR.
3. Connect an RF Cable
between the ANT OUT
terminal on the VCR and
the ANT 1 IN (AIR) or
ANT 2 IN (CABLE)
terminal on the TV.
4. Connect a Video Cable
between the VIDEO OUT
jack on the VCR and the
AV IN 1 (or AV IN 2)
[VIDEO] jack on the TV.
5. Connect Audio Cables
between the AUDIO OUT
jacks on the VCR and
the AV IN 1 (or AV IN 2)
[R-AUDIO-L] jacks
on the TV.
If you have a “mono”
(non-stereo) VCR, use a
Y-connector (not supplied)
to hook up to the right
and left audio input jacks
of the TV. If your VCR
is stereo, you must
connect two cables.
ANT 2 IN
(CABLE)
Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.
Each VCR has a different back panel configuration.
When connecting a VCR, match the color of the connection terminal to the cable.
We recommend the use of cables with a Ferrite Core.
VCR Rear Panel
TV Rear Panel
RF Cable (Not supplied)
Video Cable (Not supplied)
Audio Cable (Not supplied)
2
3
4
5
ANT 1 IN
(AIR)
Connecting an S-VHS VCR
Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR.
(This connection delivers a better picture as compared to a standard VHS VCR.)
1. To begin, follow steps 1–3
in the previous section to
connect the antenna or
cable to your VCR and
your TV.
2. Connect an S-Video Cable
between the S-VIDEO OUT
jack on the VCR and the
AV IN1 [S-VIDEO] jack on
the TV.
3. Connect Audio Cables
between the AUDIO OUT
jacks on the VCR and the
AV IN1 [R-AUDIO-L] jacks
on the TV.
An S-Video cable is usually included with an S-VHS VCR. (If not, check your local electronics store.)
Each S-VHS VCR has a different back panel configuration.
When connecting an S-VHS VCR, match the color of the connection terminal to the cable.
We recommend the use of cables with a Ferrite Core.
VCR Rear Panel
TV Rear Panel
RF Cable (Not supplied)
S-Video Cable (Not supplied)
Audio Cable (Not supplied)
3
2
1
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 10
English-11
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV.
They allow you to view the camcorder tapes without using a VCR.
1. Connect a Video Cable
between the AV IN 2
[VIDEO] jack on the TV
and the VIDEO OUT jack
on the camcorder.
Camcorder
TV Side Panel
2. Connect Audio Cables
between the AV IN 2
[R-AUDIO-L] jacks on the
TV and the AUDIO OUT
jacks on the camcorder.
Audio Cable (Not supplied)
Video Cable (Not supplied)
Connecting a DVD Player/Set-Top Box
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
1. Connect a Component
Cable between the
COMPONENT IN 1 or 2
[Y, PB, PR] jacks on the TV
and the COMPONENT OUT
[Y, PB, PR] jacks on the
DVD player.
2. Connect Audio Cables
between the COMPONENT
IN 1 or 2 [R-AUDIO-L] jacks
on the TV and the AUDIO
OUT jacks on the DVD
player.
DVD Player/Set-Top Box
TV Rear Panel
Component Cable (Not supplied)
Audio Cable (Not supplied)
Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red)
for enhanced video quality.
Be sure to match the component video and audio connections.
For example, if connecting the video cable to COMPONENT IN 1, connect the audio cable to
COMPONENT IN 1 also.
Each DVD player/STB has a different back panel configuration.
When connecting a DVD player/STB, match the color of the connection terminal to the cable.
We recommend the use of cables with a Ferrite Core.
1
2
1
2
Each Camcorder has a different back panel configuration.
When connecting a Camcorder, match the color of the connection terminal to the cable.
We recommend the use of cables with a Ferrite Core.
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 11
English-12
Connecting a DVD Player/Set-Top Box via DVI
This connection can only be made if there is a DVI Output connector on the external device.
1. Connect a DVI to HDMI
Cable or DVI-HDMI Adapter
between the HDMI/DVI IN 1
or HDMI/DVI IN 2 connector
on the TV and the DVI OUT
connector on the
DVD player/Set-Top Box.
2. Connect Audio Cables
between the DVI IN
[R-AUDIO-L] jack on the
TV and the AUDIO OUT
jacks on the DVD player/
Set-Top Box.
DVD Player/Set-Top Box
TV Rear Panel
Audio Cable (Not supplied)
2
Each DVD player/STB has a different back panel configuration.
When connecting a DVD player/STB, match the color of the connection terminal to the cable.
We recommend the use of cables with a Ferrite Core.
DVI to HDMI Cable (Not supplied)
1
Connecting a DVD Player/Set-Top Box via HDMI
This connection can only be made if there is an HDMI Output connector on the external device.
1. Connect an HDMI Cable
between the HDMI/DVI IN 1
or HDMI/DVI IN 2 connector
on the TV and the HDMI OUT
connector on the
DVD player/Set-Top Box.
DVD Player/Set-Top Box
TV Rear Panel
HDMI Cable (Not supplied)
What is HDMI?
HDMI, or high-definition multimedia interface, is a next-generation interface that enables the
transmission of digital audio and video signals using a single cable without compression.
“Multimedia interface” is a more accurate name for it especially because it allows multiple channels
of digital audio (5.1 channels). The difference between HDMI and DVI is that the HDMI device is
smaller in size, has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed,
and supports multi-channel digital audio.
Each DVD player/STB has a different back panel configuration.
We recommend the use of cables with a Ferrite Core.
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 12
English-13
Connecting a Digital Audio System
The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.
1. Connect an Optical Cable
between the “DIGITAL
AUDIO OUT (OPTICAL)”
jacks on the TV and the
Digital Audio Input jacks on
the Digital Audio System.
When a Digital Audio
System is connected to the
“DIGITAL AUDIO OUT
(OPTICAL)” terminal:
Decrease the gain (volume)
of the TV, and adjust the
volume level with the
system’s volume control.
Digital Audio System
TV Rear Panel
Optical Cable (Not supplied)
5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.
We recommend the use of cables with a Ferrite Core.
Connecting an Amplifier/DVD Home Theater
1. Connect Audio Cables
between the AV OUT
[R-AUDIO-L] on the TV
and AUDIO IN [R-AUDIO-L]
on the Amplifier/DVD Home
Theater.
When an audio amplifier is
connected to the “AV OUT
[R-AUDIO-L]” terminals:
Decrease the gain (volume)
of the TV, and adjust the
volume level with the
Amplifiers volume control.
Amplifier/DVD Home Theater
TV Rear Panel
Audio Cable (Not supplied)
Each external input source device has a different back panel configuration.
When connecting an external device, match the color of the connection terminal to the cable.
We recommend the use of cables with a Ferrite Core.
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 13
English-14
Connecting a PC
1. Connect a D-Sub Cable
between PC IN [PC]
connector on the TV and
the PC output connector
on your computer.
2. Connect a PC Audio Cable
between PC IN [AUDIO]
jack on the TV and the
Audio Out jack of the sound
card on your computer.
PC
TV Rear Panel
D-Sub Cable (Not supplied)
PC Audio Cable (Not supplied)
Each PC has a different back panel configuration.
The HDMI/DVI jacks do not support PC connection.
We recommend the use of cables with a Ferrite Core.
1
2
Internal Mute Off
Internal Mute On
Video No Signal
RF
Speaker Output
Mute
Mute
Internal Speakers
AV, S-Video
Speaker Output
Mute
Mute
Component, PC, HDMI
Speaker Output
Mute
Mute
RF
Sound Output
Sound Output
Mute
AV, S-Video
Sound Output
Sound Output
Mute
Component, PC, HDMI
Sound Output
Sound Output
Mute
When “Internal mute” is set to “On”, Sound menus except “Multi-Track Options” cannot be adjusted.
See selecting the Internal Mute on page 58.
Audio Out (Optical, L/R Out)
Connecting CableCARD
You must obtain a CableCARD from a local cable service provider.
1. Insert the CableCARD into the “CableCARD” slot and
the message “CableCARD
TM
Inserted” is displayed on
the screen. If the channel information does not
already exist, the message “Updating Channel List”
is displayed during channel information configuration.
2. When channel information configuration is finished,
the message “Updating is Completed” is displayed.
It indicates that the channel list is now updated.
TV Rear Panel
Please insert the
card as shown.
Incoming Cable
or Antenna
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 14
English-15
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the button on the front of the panel.
Plug & Play Feature
When the TV is initially powered on, two basic settings proceed automatically and subsequently:
1
Press the
POWER
button on the remote control.
The message “Shop Mode, Menu language, Channels
and Time will be set.” is displayed.
Press the ENTER button, then “Select the Home Mode
when installing this TV at home” menu is automatically
displayed.
3
Press the or button to select language, then
the ENTER button.
“Select the antennas to memorize” menu is
automatically displayed.
4
Press the or button to memorize the channels of
the selected connection.
Press the ENTER button to select “Start”.
2
Press the or buttons to select “Shop” or “Home”,
then the ENTER button.
Then “Select the language of the OSD” the menu is
automatically displayed.
Operation
If the antenna is connected to ANT 1(AIR), select “Air” and if it is
connected to ANT 2 (CABLE), select “Cable”.
If both ANT 1 (AIR) and ANT 2 (CABLE) are connected, select “Air + Cable”.
In Cable mode, you can select the correct signal source among STD,
HRC, and IRC by pressing the or button, then press the
ENTER button.
Contact your local cable company to identify the type of cable system
that exists in your particular area.
continued...
We recommend setting the TV to Home mode for the best picture in your
home environment.
Shop mode is only intended for use in retail environments.
If the unit is accidentally set to Shop Mode, press and hold the
MENU
button on the side panel of the TV for five seconds to return to Dynamic
(Home) mode.
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 15
English-16
6
Press the ENTER button.
Press the or buttons to select “Auto” or “Manual”,
then the ENTER button.
Switches the Daylight Saving Time function on or off.
7
Press the ENTER button.
Press the or buttons to select “On” or “Off”, then the
ENTER button. “Select the time zone where you are
locaed.” menu is automatically displayed.
8
Press the or buttons to highlight
the time zone for your
local area (and to move the highlight to the appropriate time
zone on the map of the United States). Press the ENTER
button. If you have received a digital signal, the time will be
set automatically. If not, see page 28 to set the clock.
9
The message “Enjoy your watching.” is displayed.
When you have finished, press the ENTER button.
The basic Plug & Play setting is available only once when the TV is initially
powered on.
If the Plug and Play is stopped while it is in progress, you must set the
functions manually by using the OSD menu.
For the Language setting, see page 19.
For the Time setting, see page 28.
For the Auto Program setting, see page 20.
5
The TV will begin memorizing all of the available channels.
After all the available channels are stored, the Auto program
menu reappears. Press the
ENTER button when channel
memorization is completed.
To stop the search before it has finished, press the ENTER
button with stop selected.
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 16
English-17
Dynamic Menus and On-Screen Displays
The on-screen menu system allows you to control the settings of your TV. Access the on-screen menu system by pressing the
MENU button on the remote control. Once the on-screen menu appears, use the / / / /ENTER buttons on your remote
control to select menu items and make adjustments. You can also view the on-screen menu system and make some adjustments
using the TV’s front (or side) panel buttons.
Viewing the Menus
Viewing the Display
1
Press the MENU button.
The main menu will appear at the bottom of the screen.
There are Eight menu groups: “Input”, “Picture”, “Sound”, “Channel”,
“Setup”, “PIP”, “Application” and “Menu Map”.
2
Press the or button, then press the ENTER button to select an
item you want in the menu.
Press the
////
ENTER buttons to display, change, or use the
selected items. Select “Return” by pressing the
or
button, then
press the ENTER button to return to the previous menu.
Press the EXIT button to exit.
Press the INFO button on the remote control. ````````
The TV displays the current channel, the status of
certain picture, sound settings and the current time.
The information displayed varies according to
the selected source.
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 17
English-18
Navigating Menus by Using the Menu Map
Using the Menu Map of the main menu enables you to select a function quickly.
1
Press the MENU button. The main menu will appear at the bottom of the screen.
2
Press the or button to select “Menu Map”, then press the ENTER button.
The menu map will appear.
3
Press the / / / buttons to select a menu, then press the ENTER button.
The selected menu will appear.
4
Press the ////ENTER buttons to display, change, or use the selected items.
Red button: Displays menus in alphabetical order.
Yellow button: Moves to the next page.
Green button: Moves to the previous page.
ENTER button: Moves to the selected menu.
Press the EXIT button to exit.
BN68-01047X-00Eng.qxd 8/29/06 2:00 PM Page 18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380

Samsung LN-S5296D Le manuel du propriétaire

Catégorie
Téléviseurs LCD
Taper
Le manuel du propriétaire