Mode AVIC F988 DAB Manuel utilisateur

Black plate (1,1)

Installation Manual

Manuel d’installation

NAVIGATION AV SYSTEM

SYSTEME DE NAVIGATION AV

SISTEMA DI NAVIGAZIONE AV

SISTEMA DE NAVEGACIÓN AV

NAVIGATIONS-/AV-SYSTEM

AV NAVIGATIESYSTEEM

AVIC-F88DAB

AVIC-F80DAB

AVIC-F980DAB

AVIC-F980BT

AVIC-F9880DAB

AVIC-F9880BT

English NederlandsDeutschEspañolItalianoFrançais

<CRD4952-B>1

Black plate (2,1)

Precautions

Your new product and this manual 3

Important safeguards 3

Connection

Precautions before connecting the

system 5

Before installing this product 5

To prevent damage 6

– Notice for the blue/white lead 6

Parts supplied 7

Connecting the power cord (1) 8

Connecting the power cord (2) 10

Connecting the system 12

Connecting to separately sold power

amp 13

Connecting an iPod / iPhone or an Android

device 14

Attaching identification labels to USB

cables 15

Connecting an iPhone with Lightning

connector 15

– Connecting via the USB port

(iPhone) 15

– Connecting via the HDMI port

(iPhone) 16

– Connecting via the RGB input

(iPhone) 16

Connecting an iPhone with 30-pin

connector 17

– Connecting via the AUX input

(iPhone) 17

– Connecting via the RGB input

(iPhone) 18

Connecting the Android™ device 18

– Connecting via the HDMI port (Android

device) 18

– Connecting via the MHL port (Android

device) 19

Connecting via the USB port (Android

device) 19

Securing the High Speed HDMI

®

Cable 20

Connecting a rear view camera 20

Connecting the external video

component 21

– Using AV input 21

– Using an AUX input 22

Connecting an HDMI device 23

Connecting the rear display 24

– When using a rear display connected to

rear video output 24

Installation

Precautions before installation 25

To avoid electromagnetic interference 25

Before installing 25

– For AVIC-F88DAB and AVIC-F80DAB

users 26

Installing this product 26

– Installation notes 26

– Parts supplied 27

– Before installing this product 27

– Installation with the holder 27

– Installation using the screw holes on

the side of this product 28

Installing the GPS aerial 29

– Installation notes 29

– When installing the aerial inside the

vehicle (on the dashboard or rear

shelf) 30

Installing the microphone 31

– Parts supplied 31

– Mounting on the sun visor 31

– Installation on the steering column 32

– Adjusting the microphone angle 32

After installation

After installing this product 33

<CRD4952-B>2

Contents

Engb

2

Black plate (3,1)

Your new product and this

manual

! The navigation features of this product

(and the rear view camera option if pur-

chased) are intended solely to aid you in

the operation of your vehicle. It is not a sub-

stitute for your attentiveness, judgement

and care when driving.

! Never use this product to route to hospi-

tals, police stations, or similar facilities in

an emergency. Please call the appropriate

emergency number.

! Do not operate this product, any applica-

tions, or the rear view camera option (if pur-

chased) if doing so will divert your attention

in any way from the safe operation of your

vehicle. Always observe safe driving rules

and follow all existing traffic regulations. If

you experience difficulty in operating this

product or reading the display, park your

vehicle in a safe location and apply the

handbrake before making the necessary

adjustments.

! This manual explains how to install this

product in your vehicle. Operation of this

product is explained in the separate man-

uals.

! Do not install this product where it may (i)

obstruct the driver’s vision, (ii) impair the

performance of any of the vehicle’s operat-

ing systems of safety features, including

airbags, hazard lamp buttons, or (iii) impair

the driver’s ability to safely operate the vehi-

cle. In some cases, it may not be possible

to install this product because of the vehi-

cle type or the shape of the vehicle interior.

! Model icons shown in this manual indicate

that the description is intended for the

models indicated by the icons.

If the following icon is shown, the descrip-

tion is applied only to the model shown.

e.g.)

F88DAB

! The graphical symbol placed on

the product means direct current.

Important safeguards

WARNING

Pioneer does not recommend that you install

this product yourself. This product is de-

signed for professional installation only. We

recommend that only authorised Pioneer ser-

vice personnel, who have special training

and experience in mobile electronics, set up

and install this product. NEVER SERVICE

THIS PRODUCT YOURSELF. Installing or

servicing this product and its connecting

cables may expose you to the risk of electric

shock or other hazards, and can cause da-

mage to this product that is not covered by

warranty.

! Read this manual fully and carefully before

installing this product.

! Keep this manual handy for future refer-

ence.

! Pay close attention to all warnings in this

manual and follow the instructions care-

fully.

! This product may in certain circumstances

display inaccurate position of your vehicle,

the distance of objects shown on the

screen, and compass directions. In addi-

tion, the system has certain limitations, in-

cluding the inability to identify one-way

streets, temporary traffic restrictions and

potentially unsafe driving areas. Please ex-

ercise your own judgement in the light of

actual driving conditions.

! As with any accessory in your vehicle’s in-

terior, this product should not divert your

attention from the safe operation of your

vehicle as it may result in serious injury or

death. If you experience difficulty in operat-

ing the system or reading the display,

please make adjustments while safely

parked.

! Please remember to wear your seat belt at

all times while operating your vehicle. If

you are in an accident, your injuries can be

considerably more severe if your seat belt

is not properly fastened.

<CRD4952-B>3

Engb

3

English

Section

01

Precautions

Black plate (4,1)

! Certain country and government laws may

prohibit or restrict the placement and use

of this product in your vehicle. Please com-

ply with all applicable laws and regulations

regarding the use, installation and opera-

tion of this product.

<CRD4952-B>4

Engb

4

Section

01

Precautions

Black plate (5,1)

Precautions before

connecting the system

WARNING

Do not take any steps to tamper with or dis-

able the handbrake interlock system which

is in place for your protection. Tampering

with or disabling the handbrake interlock

system could result in serious injury or

death.

CAUTION

! If you decide to perform the installation

yourself, and have special training and ex-

perience in the mobile electronics instal-

lations, please carefully follow all of the

steps in the installation manual.

! Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wir-

ing to remain exposed.

! Do not directly connect the yellow lead of

this product to the vehicle battery. If the

lead is directly connected to the battery,

engine vibration may eventually cause

the insulation to fail at the point where

the wire passes from the passenger com-

partment into the engine compartment. If

the yellow lead’s insulation tears as a re-

sult of contact with metal parts, short-cir-

cuiting can occur, resulting in

considerable danger.

! It is extremely dangerous to allow cables

to become wound around the steering col-

umn or gearstick. Be sure to install this

product, its cables, and wiring away in

such so that they will not obstruct or hin-

der driving.

! Make sure that the cables and wires will

not interfere with or become caught in

any of the vehicle’s moving parts, espe-

cially the steering wheel, gearstick, hand-

brake, sliding seat tracks, doors, or any of

the vehicle’s controls.

! Do not route wires where they will be ex-

posed to high temperatures. If the insula-

tion heats up, wires may become

damaged, resulting in a short circuit or

malfunction and permanent damage to

the product.

! Do not cut the GPS aerial cable to shorten

it or use an extension to make it longer.

Altering the aerial cable could result in a

short circuit or malfunction.

! Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse resis-

tor or filter, etc.) may fail to work properly.

! Never feed power to other electronic pro-

ducts by cutting the insulation of the

power supply lead of this product and tap-

ping into the lead. The current capacity of

the lead will be exceeded, causing over-

heating.

Before installing this product

! Use this product with a 12-volt battery and

negative earthing only. Failure to do so may

result in a fire or malfunction.

! To avoid shorts in the electrical system, be

sure to disconnect the (–) battery cable be-

fore installation.

<CRD4952-B>5

Engb

5

English

Section

02

Connection

Black plate (6,1)

To prevent damage

WARNING

! Use speakers over 50 W (maximum input

power) and between 4 W to 8 W (impe-

dance value). Do not use 1 W to 3 W speak-

ers for this product.

! The black lead is earth. Please earth this

lead separately from the earth of high-cur-

rent products such as power amps. Do not

earth more than one product together

with the earth from another product. For

example, you must separately earth any

amp unit away from the earth of this pro-

duct. Connecting earths together can

cause a fire and/or damage the products if

their earths became detached.

! When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

! When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

! This product cannot be installed in a vehi-

cle without ACC (accessory) position on

the ignition switch.

A

C

O

N

S

T

A

R

T

O

F

O

N

S

T

A

R

T

O

F

ACC position No ACC position

! To avoid short-circuiting, cover the discon-

nected lead with insulating tape. It is espe-

cially important to insulate all unused

speaker leads, which if left uncovered may

cause a short circuit.

! Attach the connectors of the same colour

to the corresponding coloured port, i.e.,

blue connector to the blue port, black to

black, etc.

! Refer to the owner’s manual for details on

connecting the power amp and other units,

then make connections accordingly.

! Since a unique BPTL circuit is employed,

do not directly earth the * side of the

speaker lead or connect the * side of an-

other side of the speaker lead together. Be

sure to connect the * side of the speaker

lead to the * side of the speaker lead on

this product.

Notice for the blue/white lead

Important

When this product is in “Power OFF” mode, the

control signal is also turned off. If “Power OFF”

mode is cancelled, the control signal is output

again and the aerial is extended with the auto aer-

ial function (if the aerial is being used). Be careful

so that the extended aerial does not come into

contact with any obstacles.

! When the ignition switch is turned on (ACC

ON), a control signal is output through the

blue/white lead. Connect to an external

power amp’s system remote control term-

inal, the auto-aerial relay control terminal,

or the aerial booster power control terminal

(max. 300 mA 12 V DC). The control signal

is output through the blue/white lead, even

if the audio source is switched off.

! Be sure not to use this lead as the power

supply lead for the external power amps.

Such connection could cause excessive

current drain and malfunction.

! Be sure not to use this lead as the power

supply lead for the auto-aerial or aerial

booster. Such connection could cause ex-

cessive current drain and malfunction.

<CRD4952-B>6

Engb

6

Section

02

Connection

Black plate (7,1)

Parts supplied

This product Power cord

GPS aerial Microphone

USB cable

(2 pcs.)

USB cable identifica-

tion labels

Lock tie*1 Vehicle Bus conversion

cable*2

Metal sheet Clamp (3 pcs.)

Double-sided tape

Notes

! (*1) These parts are supplied with AVIC-

F88DAB.

! (*2) These parts are supplied with AVIC-

F88DAB, AVIC-F80DAB and AVIC-

F980DAB.

<CRD4952-B>7

Engb

7

English

Section

02

Connection

Black plate (8,1)

Connecting the power cord (1)

Depending on the types of vehicles, the

function of *2 and *4 may be different. In this

case, be sure to connect *1 to *4 and *3 to *2

as shown in the figure.

Connect leads of the

same colour to each other.

Yel lo w (*2)

Back-up

(or accessory)

Red (*4)

Accessory

(or back-up)

Yel lo w (*1)

To terminal supplied with

power regardless of ignition

switch position.

Red (*3)

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (earth)

To vehicle (metal) body.

Note

In some vehicles, the ISO connector may be divided

into two. In this case, be sure to connect to both

connectors.

Note

*2 *1

*4 *3

ISO connector

Speaker leads

White: Front left 

White/black: Front left 

Grey: Front right 

Grey/black: Front right 

Green: Rear left 

Green/black: Rear left 

Violet: Rear right 

Violet/black: Rear right 

<CRD4952-B>8

Engb

8

Section

02

Connection

Black plate (9,1)

Note

The pin position of the ISO connector will differ

depending on the types of vehicles. Connect *5

and *6 when Pin 5 is an aerial control type. In

other types of vehicles, never connect *5 and *6.

Yellow/black (MUTE)

If you use equipment with a mute function, connect

that equipment to the Audio Mute lead. If not, keep

the Audio Mute lead free of any connections.

Power cord

Audio source will be set to mute or attenuate, while the

following sounds will not be muted or attenuated. For details,

refer to Operation Manual.

— Voice guidance of the navigation

— Incoming ringtone and incoming voice of the mobile phone

that is connected to this product via Bluetooth wireless

technology

This product

14 cm

Fuse (10 A)

Blue/white (*5)

Blue/white (*6)

To auto-aerial relay control terminal or

aerial booster power control terminal

(max. 300 mA 12 V DC).

Power supply

<CRD4952-B>9

Engb

9

English

Section

02

Connection

Black plate (10,1)

Connecting the power cord (2)

Pink (CAR SPEED SIGNAL INPUT)

This product is connected here to detect the distance the vehicle travels. Always connect the

vehicle’s speed detection circuit. Failure to make this connection will increase errors in the

vehicle’s location display.

LIGHT GREEN LEAD AT POWER CONNECTOR IS

DESIGNED TO DETECT PARKED STATUS AND MUST BE

CONNECTED TO THE POWER SUPPLY SIDE OF THE

HANDBRAKE SWITCH. IMPROPER CONNECTION OR

USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW

AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.

Light green (PARKING BRAKE)

Used to detect the ON/OFF status of the handbrake. This lead must be connected to the power supply side

of the handbrake switch.

If this connection is made incorrectly or omitted, certain functions of this product will be unusable.

Power supply side

Earth side

Handbrake switch

Connection method

Clamp the lead of the power supply

side of the handbrake switch.

Clamp firmly with needle-nosed

pliers.

The position of the speed detection circuit and the position of the handbrake switch vary

depending on the vehicle model. For details, consult your authorised Pioneer dealer or an

installation professional.

Note

WARNING

CAUTION

It is strongly suggested that the speed pulse wire be connected for accuracy of navigation

and better performance.

IMPROPER CONNECTION MAY RESULT IN SERIOUS DAMAGE OR INJURY INCLUDING

ELECTRICAL SHOCK, AND INTERFERENCE WITH THE OPERATION OF THE VEHICLE´S

ANTILOCK BRAKING SYSTEM, AUTOMATIC GEARBOX AND SPEEDOMETER INDICATION.

WARNING

<CRD4952-B>10

Engb

10

Section

02

Connection

Black plate (11,1)

Violet/white (REVERSE-GEAR SIGNAL INPUT)

This is connected so that this product can detect whether

the vehicle is moving forwards or backwards. Connect the

violet/white lead to the lead whose voltage changes when

the reverse gear is engaged. Unless connected, the sensor

may not detect your vehicle travelling forward/backward

properly, and thus the position of your vehicle detected by

the sensor may be misaligned from the actual position.

When you use a rear view camera, please make

sure to connect this lead. Otherwise you cannot

switch to the rear view camera picture.

This product

Note

Power cord

Power supply

<CRD4952-B>11

Engb

11

English

Section

02

Connection

Black plate (12,1)

Connecting the system

This product

Wired remote input

Please refer to the instruction manual for

the Hard-wired remote control adapter

(sold separately).

3.55 m

Aerial jack

Vehicle aerial

Microphone

3 m

Vehicle Bus

conversion cable

15.8 cm

WARNING

Vehicle Bus adapter input

Please refer to the instruction manual for

the Vehicle Bus adapter (sold separately).

· To avoid the risk of accident and the potential violation of applicable laws, this product should

never be used while the vehicle is being driven except for navigation purposes. And, also rear

displays should not be in a location where it is a visible distraction to the driver.

· In some countries, the viewing of images on a display inside a vehicle even by persons other than

the driver may be illegal. Where such regulations apply they must be obeyed and this product’s

video source should not be used.

GPS aerial

CAUTION:

For improved Digital Radio reception, make sure

a Digital Radio aerial with phantom power input

(active type) is used. Pioneer recommends

using AN-DAB1 or CA-AN-DAB.001 (sold

separately). Current consumption of the Digital

Radio aerial should be 100 mA or less.

DAB aerial input

F80DAB F980DABF88DAB

<CRD4952-B>12

Engb

12

Section

02

Connection

Black plate (13,1)

Connecting to separately sold power amp

























System remote control

Power cord

Blue/white

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

Front speaker

Rear speaker

Subwoofer

RCA

cables

(sold separately)

This product

15 cm

Rear outputs

(REAR OUTPUT)

Front outputs

(FRONT OUTPUT)

To system control terminal of the power amp

(max. 300 mA 12 V DC).

White, Red (SWL, SWR)

Notes

· You can change the RCA output of the subwoofer depending on your subwoofer

system. (Refer to Operation Manual.)

· The subwoofer output of this product is monaural.

If your vehicle is

equipped with an

auto-aerial, connect

this lead to a power

amp.

Power supply

<CRD4952-B>13

Engb

13

English

Section

02

Connection

Black plate (14,1)

Connecting an iPod / iPhone or an Android device

Find your device and the function you want to operate from the list below, and refer to the page for the connection.

p Depending on the device, some functions may not be available.

iPhone (5, 5c, 5s, 6, 6 Plus)/iPod touch (5th generation)

iPod (audio)

Apple CarPlay

AVICSYNC App

Refer to Connecting via the USB port (iPhone) on page 15.

AppRadio Mode

AVICSYNC App

F88DAB

Refer to Connecting via the HDMI port (iPhone) on page 16.

F80DAB F980DAB

F980BT

F9880DAB

F9880BT

Refer to Connecting via the RGB input (iPhone) on page 16.

iPhone 3GS/iPod touch (2nd, 3rd generation)/iPod classic (80GB, 160GB)/iPod nano (3rd, 4th, 5th, 6th gen-

eration)

iPod (audio)

iPod (video)

Refer to Connecting via the AUX input (iPhone) on page 17.

iPhone (4, 4s)/iPod touch (4th generation)

iPod (audio)

iPod (video)

AppRadio Mode

AVICSYNC App

Refer to Connecting via the RGB input (iPhone) on page 18.

iPod nano (7th generation)

iPod (audio) Refer to Connecting via the USB port (iPhone) on page 15.

Android device

F88DAB

AppRadio Mode

HDMI port

Refer to Connecting via the HDMI port (Android device) on page 18.

MHL port

Refer to Connecting via the MHL port (Android device) on page 19.

AVICSYNC App

F88DAB

F80DAB

Android Auto

Refer to Connecting via the USB port (Android device) on page 19.

AVICSYNC App

<CRD4952-B>14

Engb

14

Section

02

Connection

Black plate (15,1)

Attaching identification

labels to USB cables

Attach identification labels to USB cables be-

fore installing this product in a vehicle.

1 Connect USB cables to the USB port 1

and 2 on the rear of this product.

2 Attach the identification labels corre-

sponding to each port to the USB cables as

illustrated below.

Attach the “PORT 1” label to the USB cable

connected to the USB port 1.

Attach the “PORT 2” label to the USB cable

connected to the USB port 2.

Connecting an iPhone with

Lightning connector

Notes

! For details on how to connect an external de-

vice using a separately sold cable, refer to the

manual for the cable.

! For details concerning the connection, opera-

tions and compatibility of iPhone, refer to Op-

eration Manual.

Connecting via the USB port

(iPhone)

The USB interface cable for iPod / iPhone (CD-

IU52) (sold separately) is required for the con-

nection.

p When using Apple CarPlay, connect the

iPhone to USB port 1.

This product

USB port 1

iPhone with

Lightning connector

USB cable

1.5 m

USB interface cable for iPod / iPhone

(CD-IU52) (sold separately)

USB port 2

<CRD4952-B>15

Engb

15

English

Section

02

Connection

Black plate (16,1)

Connecting via the HDMI port

(iPhone)

F88DAB

The following cables are required for the con-

nection.

! HDMI interface cable for iPod / iPhone

(CD-IH202) (sold separately)

! USB interface cable for iPod / iPhone (CD -

IU52) (sold separately)

! Lightning Digital AV Adapter (Apple Inc.

products) (sold separately)

This product

USB port 1

USB interface cable for iPod / iPhone

(CD-IU52) (sold separately)

iPhone with

Lightning connector

High Speed HDMI

®

Cable

(Type A - A)

(supplied with CD-IH202)

HDMI port

Lightning Digital AV Adapter

(Apple Inc. products)

(sold separately)

USB cable

1.5 m

Note

When you connect the High Speed HDMI

®

Cable,

use the lock tie to fix it securely.

= For details, refer to Securing the High Speed

HDMI

®

Cable on page 20.

Connecting via the RGB input

(iPhone)

F80DAB F980DAB F980BT

F9880DAB

F9880BT

The following cables are required for the con-

nection.

! VGA/USB interface cable for iPod / iPhone

(CD-IV202AV) (sold separately)

! USB interface cable for iPod / iPhone (CD -

IU52) (sold separately)

! Lightning to VGA Adapter (Apple Inc. pro-

ducts) (sold separately)

<CRD4952-B>16

Engb

16

Section

02

Connection

Black plate (17,1)

Lightning to VGA Adapter

(Apple Inc. products)

(sold separately)

This product

USB port 1

RGB input

iPhone with

Lightning connector

USB interface cable for iPod / iPhone

(CD-IU52) (sold separately)

VGA/USB interface cable

for iPod / iPhone

(CD-IV202AV) (sold separately)

Connecting an iPhone with

30-pin connector

Notes

! For details on how to connect an external de-

vice using a separately sold cable, refer to the

manual for the cable.

! For details concerning the connection, opera-

tions and compatibility of iPhone, refer to Op-

eration Manual.

Connecting via the AUX input

(iPhone)

The USB interface cable for iPod / iPhone (CD-

IU201V) (sold separately) is required for the

connection.

This product

USB interface cable for iPod / iPhone

(CD-IU201V) (sold separately)

USB cable

1.5 m

iPhone with

30-pin connector

AUX input

USB port 1

USB port 2

Mini-jack extension cable

(supplied with CD-IU201V)

<CRD4952-B>17

Engb

17

English

Section

02

Connection

Black plate (18,1)

Connecting via the RGB input

(iPhone)

The USB interface cable for iPod / iPhone (CD-

IU201S) (sold separately) is required for the

connection.

USB cable

1.5 m

USB interface cable for iPod / iPhone

(CD-IU201S) (sold separately)

This product

USB port 1

RGB input

iPhone with

30-pin connector

Connecting the Android

™

device

F88DAB

App Connectivity Kit (CD-AH200) (sold sepa-

rately) is required for the connection.

Notes

! For details on how to connect an external de-

vice using a separately sold cable, refer to the

manual for the cable.

! For details concerning the connection and op-

erations of Android device, refer to Operation

Manual.

! When you connect the High Speed HDMI

®

Cable, use the lock tie to fix it securely.

= For details, refer to Securing the High

Speed HDMI

®

Cable on page 20.

Connecting via the HDMI port

(Android device)

USB cable

1.5 m

This product

Android device

USB port 2

HDMI port

High Speed HDMI

®

Cable (Type A - A)

(supplied with

CD-AH200)

USB - micro USB cable

(Type USB A - micro USB B)

(supplied with CD-AH200)

Adapter cable

(HDMI Type A - D)

(supplied with CD-AH200)

<CRD4952-B>18

Engb

18

Section

02

Connection

Black plate (19,1)

Connecting via the MHL port

(Android device)

USB cable

1.5 m

This product

Android device

USB port 2

HDMI port

High Speed HDMI

®

Cable

(Type A - A)

(supplied with CD-AH200)

USB - micro USB cable

(Type USB A - micro USB B)

(supplied with CD-AH200)

MHL adapter

(supplied with

CD-AH200)

Connecting via the USB

port (Android device)

The USB interface cable for use with Android

devices (CD-MU200) (sold separately) is re-

quired for the connection.

USB cable

1.5 m

USB - micro USB cable

(Type USB A - micro USB B)

(supplied with CD-MU200)

This product

Android device

USB port 2

Note

For details on how to connect an external device

using a separately sold cable, refer to the manual

for the cable.

<CRD4952-B>19

Engb

19

English

Section

02

Connection

Black plate (20,1)

Securing the High Speed

HDMI

®

Cable

F88DAB

Be sure to fix the High Speed HDMI

®

Cable

with the lock tie, when you connect the exter-

nal device with the High Speed HDMI

®

Cable.

1 Insert the High Speed HDMI

®

Cable into

the HDMI port.

2 Wrap the lock tie around the hook

above the HDMI port and the High Speed

HDMI

®

Cable, and then tighten it to secure

the High Speed HDMI

®

Cable.

1

2

3

1 Hook

2 Lock tie

3 High Speed HDMI

®

Cable

p Do not tighten up the lock tie more than

necessary.

Connecting a rear view camera

When this product is used with a rear view

camera, it is possible to automatically switch

from the video to rear view image when the

gearstick is moved to REVERSE (R). Camera

View mode also allows you to check what is

behind you while driving.

WARNING

USE INPUT ONLY FOR REVERSE OR MIRROR

IMAGE REAR VIEW CAMERA. OTHER USE MAY

RESULT IN INJURY OR DAMAGE.

CAUTION

! The screen image may appear reversed.

! The rear view camera is used as an aid to

keep an eye on trailers, or backing into a tight

parking spot. Do not use this function for en-

tertainment purposes.

! Objects in rear view may appear closer or

more distant than in reality.

! Please note that the image area shown by the

rear view camera may differ slightly when full-

screen images are displayed when backing

and when checking the rear of the vehicle

while moving forward.

<CRD4952-B>20

Engb

20

Section

02

Connection

La page charge ...

Mode AVIC F988 DAB Manuel utilisateur

Mode AVIC F988 DAB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents