DeWalt Pressure Washer DPD3100 Manuel utilisateur

DPD3100

Pressure Washer

Laveuse à pression

Lavadora a presión

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-De

2



A. Panel assembly

B. Nozzle holder

C. Professional Spray gun

D. Side Handle

E. Quick-connect

spray wand

F. Frame

G. Engine dipstick/oil plug

H. Engine switch

I. Starter grip

J. Engine

K. Choke control

L. Throttle control lever

M. Fuel valve lever

N. Gas cap

O. Handle assembly

P. High-pressure hose

Q. High-pressure pump

DPD3100 PRESSURE WASHER



Refer to the engine instruction manual for location and operation of

other engine controls.



DeWALT MAINTENANCE FREE DESIGN

The high pressure pump is maintenance free and requires no oil. If

there is a problem with the pump contact a D

eWA LT factory service

center, a D

eWA LT authorized service center or other qualified service

personnel.

FIG. 1

J

C

E

P

K

O

A

F

B

Q

H

G

N

L

M

I

D

3



IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

eWALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

eWALT (1-800-433-9258)



WARNING: Do not operate this unit until you read and understand

this instruction manual and the engine instruction manual for safety,

operation and maintenance instructions.

WARNING: When using this product basic precautions should

always be followed, including the following:

1. Read all instructions before using the product.

2. To reduce the risk of injury, close supervision is necessary when

a product is used near children.

3. Know how to stop the product and bleed pressures quickly. Be

thoroughly familiar with the controls.

4. Stay alert–watch what you are doing.

5. Do not operate the product when fatigued or under the influence

of alcohol or drugs.

6. Keep operating area clear of all persons.



The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death

or serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which, if

not avoided, may result in property damage.



MODEL WEIGHT HEIGHT WIDTH LENGTH PSI MAX* AVERAGE

OPERATING

PSI

GPM MAX* AVERAGE

OPERATING

GPM

ENGINE

DPD3100 83.6 lbs 26.5" 23" 40" 3100

(21373 kPa)

2780

(19167 kPa)

2.8

(10.6 L/min)

2.7

(10.3 L/min)

DeWALT

196 cc OHV,

5.5 Net HP, 6.5

Gross HP **

* Maximum PSI and GPM ratings determined in accordance with the Pressure Washers Manufacturers Association (PWMA)

standard PW101

** Horsepower rating (shown as maximum output @ 3600 rpm) is in accordance with SAE J1349 for Net HP and SAE J1995 for Gross HP.

Actual engine power will be lower. Engine power depends on the application, operating speed, operating conditions and other variables.

4



7. Do not overreach or stand on unstable support. Keep good

footing and balance at all times.

8. Follow the maintenance instructions speciﬁed in the manual.

DANGER: RISK OF INJECTION OR SEVERE INJURY. KEEP

CLEAR OF NOZZLE. DO NOT DIRECT DISCHARGE STREAM AT

PERSONS. THIS PRODUCT IS TO BE USED ONLY BY TRAINED

OPERATORS.

WARNING: This product may not be equipped with a spark-

arresting muffler. If the product is not equipped and will be used

around flam ma ble ma teri als or on land covered with materials such

as agricultural crops, forest, brush, grass or other similar items, then

an ap proved spark arrester must be installed and is legally required

in the state of California. It is a violation of California statutes

section 130050 and/or sec tions 4442 and 4443 of the California

Public Re sourc es Code, unless the engine is equipped with a spark

arrester, as defined in section 4442, and maintained in ef fec tive

work ing order. Spark arresters are also required on some U.S.

For est Service land and may also be legally required under other

statutes and or di nanc es.

WARNING: This product contains chemicals, known to the

State of California to cause cancer, and birth defects or other

reproductive harm. Wash hands after handling.



DANGER: RISK OF EXPLOSION OR FIRE

What can happen How to prevent it

 • Spilledgasolineandit’s

vapors can be come ignited

from cigarette sparks,

electrical arcing, exhaust

gas es and hot engine

components such as

the muffler.

 • Shutoffengineandallow

it to cool before adding fuel

to the tank.

 • Usecareinfillingtankto

avoid spill ing fuel. Move pres-

sure wash er away

from fueling area before

start ing en gine.

 • Heatwillexpandfuelinthe

tank which could result in

spillage and pos si ble fire

explosion.

 • Keepmaximumfuellevel

1/2" (12.7 mm) be low

bottom of filler neck

to allow for expansion.

 • Operatingthepressure

washer in an ex plo sive

en viron ment could

re sult in a fire.

 • Operateandfuelequipment

in well-ven ti lat ed areas free

from ob struc tions. Equip

areas with fire extinguisher

suit able for gas o line fires.

 • Materialsplacedagainstor

near the pressure washer

can in ter fere with its proper

ventilation fea tures caus ing

overheating and possible

ig ni tion of the materials.

 • Neveroperatepressure

wash er in an area containing

dry brush or weeds.

5



 • Mufflerexhaustheatcan

damage paint ed sur fac es,

melt any material sen si tive

to heat (such as siding,

plas tic, rub ber, vinyl or the

pressure hose, itself), and

dam age live plants.

 • Alwayskeeppressurewasher

a min i mum of 4' (1.2 m) away

from sur fac es (such as

houses, au to mo biles or

live plants) that could be

damaged from muffler exhaust

heat.

 • Improperly stored fuel could

lead to acciden tal ignition.

Fuel im prop er ly secured

could get into the hands of

children or oth er un qual i fied

persons.

 • StorefuelinanOSHA

approved con tain er, in a

se cure location away from

work area.

 • Useofacids,toxicor

cor ro sive chemicals,

poisons, in sec ti cides, or any

kind of flam ma ble solvent

with this product could re sult

in se ri ous injury or death.

 • Donotsprayflammable

liquids.

DANGER: RISK TO BREATHING (ASPHYXIATION)

What can happen How to prevent it

 • Breathingexhaustfumes

will cause se ri ous injury

or death! En gine exhaust

con tains carbon mon ox ide,

an odorless and deadly gas.

 • Operatepressurewasherin

a well-ventilated area. Avoid

en closed areas such as ga rag-

es, base ments, etc.

 • Neveroperateunitina

lo ca tion occupied by

humans or animals.

DANGER: RISK TO BREATHING (ASPHYXIATION) CONTINUED

 • Somecleaningfluids

con tain sub stanc es which

could cause injury to skin,

eyes or lungs.

 • Useonlycleaningfluids

spe cif i cal ly rec om mend ed

for high-pressure washers.

Fol low manufacturers

recommendations. Do not use

chlorine bleach or any other

corrosive compound.

DANGER: RISK OF FLUID INJECTION AND LACERATION

What can happen How to prevent it

 • Yourpressurewasher

operates at fluid pressures

and velocities high enough to

penetrate human and

animal flesh, which could

result in amputation or

other serious injury. Leaks

caused by loose fittings or

worn or damaged hoses can

result in injection injuries.

DO NOT TREAT FLUID

INJECTION AS

A SIMPLE CUT! See a

physician immediately!

 • Inspectthehigh-pressure

hose regularly. Replace

the hose immediately if it is

damaged, worn, has melted

from contacting the engine,

or shows any signs of cracks,

bubbles, pinholes, or other

leakage. Never grasp a

high-pressure hose that

is leaking or damaged.

 • Nevertouch,grasporattempt

to cover a pinhole or similar

water leak on the high-

pressure hose. The stream

of water IS under high

pressure and WILL

penetrate skin.

 • Neverplacehandsinfront

of noz zle.

6



DANGER: RISK OF INJURY FROM SPRAY

What can happen How to prevent it

 • High-velocityfluidspray

can cause objects to break,

propelling particles at high

speed.

 • AlwayswearANSI-approved

Z87.1 safety glasses. Wear

protective clothing to protect

against accidental spraying.

 • Neverpointwandatorspray

people or animals.

 • Lightorunsecuredobjects

can become hazardous

projectiles.

 • Alwayssecuretriggerlock

when wand is not in service

to prevent accidental

operation.

 • Neverpermanentlysecure

trigger in pull-back (open)

position.

DANGER:

RISK OF FLUID INJECTION AND LACERATION

CONTINUED

 • Yourpressurewasher

operates at fluid pressures

and velocities high enough to

penetrate human and

animal flesh, which could

result in amputation or

other serious injury. Leaks

caused by loose fittings or

worn or damaged hoses can

result in injection injuries.

DO NOT TREAT FLUID

INJECTION AS

A SIMPLE CUT! See a

physician immediately!

 • Directsprayawayfromself

and others.

 • Makesurehoseandfittings

are tight ened and in good

condition. Never hold onto

the hose or fittings during

op er a tion.

 • Donotallowhosetocontact

muf fler.

 • Neverattachorremovewand

or hose fittings while sys tem is

pres sur ized.

 • Whenusingreplacement

lances or guns with this

pressure washer, DO NOT

use a lance and/or lance/gun

combination that is shorter

in length than what was

provided with this pressure

washer as measured from the

nozzle end of the lance to the

gun trigger.

 • Injuriescanresultifsystem

pressure is not reduced

before attempting mainte-

nance or disassembly.

 • Torelievesystempressure,

shut off engine, turn off water

sup ply and pull gun trigger

until water stops flowing.

 • Use only accessories rated

equal to or higher than the

rating of the pressure washer.

7



DANGER: RISK OF UNSAFE OPERATION

What can happen How to prevent it

 • Unsafeoperationofyour

pressure wash er could lead

to se ri ous in ju ry or death to

you or others.

 • Donotusechlorine

bleach or any other

corrosive compound.

 • Becomefamiliarwiththeoper-

a tion and con trols of

the pressure washer.

 • Keepoperatingareaclear

of all persons, pets and

obstacles.

 • Donotoperatetheproduct

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

 • Neverdefeatthesafety

fea tures of this prod uct.

 • Donotoperatemachine

with missing, broken or

un au tho rized parts.

 • Neverleavewand

unattended while unit

is running.

 • Ifproperstartingprocedure

is not followed, engine can

kickback causing serious

hand and arm injury.

 • Ifenginedoesnotstartafter

two pulls, squeeze trigger

of gun to relieve pump

pressure. Pull starter cord

slowly until resistance is felt.

Then pull cord rapidly to avoid

kickback and prevent hand or

arm injury.

 • Thespraygun/wandis

a powerful clean ing tool

that could look like a toy

to a child.

 • Keepchildrenawayfromthe

pressure washer at all times.

 • Reactiveforceofspray

will cause gun/wand to

kickback, and could cause

the op er a tor to slip or fall

or misdirect the spray.

Im prop er control of gun/

wand can re sult in

in ju ries to self and

others.

 • Donotoverreachorstand

on an unstable support.

 • Donotusepressurewasher

while standing on a ladder.

 • Gripgun/wandfirmlywith

both hands. Expect the

gun to kickback when

triggered.

8



DANGER: RISK OF INJURY OR PROP ER TY DAMAGE WHEN

TRANSPORTING OR STORING

What can happen How to prevent it

 • Fueloroilcanleakorspill

and could result in fire or

breathing hazard. Se ri ous

in ju ry or death can re sult.

Fuel or oil leaks will dam age

carpet, paint or oth er

surfaces in ve hi cles

or trailers.

 • Ifpressurewasherisequipped

with a fuel shut-off valve, turn

the valve to the OFF position

before transporting to avoid

fuel leaks. If pres sure wash er

is not equipped with a fuel

shut-off valve, drain the fuel

from tank before trans port-

ing. Only trans port fuel in an

OSHA-approved container.

Al ways place pressure washer

on a protective mat when

transporting to protect against

dam age to vehicle from leaks.

Re move pres sure washer

from vehicle immediately upon

arrival at your destination.

WARNING: RISK OF BURSTING

What can happen How to prevent it

 • Over inflation of tires could

result in serious injury and

property damage.

 • Useatirepressuregaugeto

check the tires pressure before

each use and while inflating

tires; see the tire sidewall for

the correct tire pressure.

NOTE: Air tanks,

compressors and similar

equipment used to inflate

tires can fill small tires similar

to these very rapidly. Adjust

pressure regulator on air

supply to no more than the

rating of the tire pressure.

Add air in small increments

and frequently use the tire

gauge to prevent over

inflation.

• High-velocityfluidspray

directed at pneumatic tire

sidewalls (such as found

on automobiles, trailers and

the like) could damage the

sidewall resulting in serious

injury.

• Onpressurewashersrated

above 1600 PSI (11032 kPa)

use the widest fan spray

(40º nozzle) and keep the

spray a minimum of 8"

(20 cm) from the pneumatic

tire sidewall. Do not aim spray

directly at the joint between

the tire and rim.

9



WARNING: RISK OF HOT SURFACES

What can happen How to prevent it

 • Contactwithhotsurfaces,

such as engines exhaust

com po nents, could result in

se ri ous burn.

 • Duringoperation,touch

only the control surfaces

of the pres sure washer.

Keep children away from

the pres sure washer at all

times. They may not be able

to recognize the haz ards of

this product.

WARNING: RISK OF CHEMICAL BURN

What can happen How to prevent it

 • Useofacids,toxicor

corrosive chemicals, poisons,

in sec ti cides, or any kind of

flam ma ble solvent with this

product could re sult in se ri-

ous injury or death.

 • Donotsprayacids,gasoline,

ker o sene, or any other

flammable materials with this

product. Use only household

de ter gents, cleaners and

degreasers recommended

for use with pres sure

washers.

 • Wearprotectiveclothing

to protect eyes and skin

from con tact with sprayed

materials.

WARNING: RISK OF

ELEC TRI CAL SHOCK

What can happen How to prevent it

 • Spraydirectedatelectrical

outlets or switch es, or ob jects

con nect ed to an elec tri cal

circuit, could re sult in a

fatal electrical shock.

 • Unpluganyelectrically

op er at ed product before

attempting to clean it. Direct

spray away from electric

out lets and switches.

WARNING: RISK OF

INJURY FROM LIFTING

What can happen How to prevent it

 • Seriousinjurycanresult

from attempting to lift too

heavy an object.

 • Thepressurewasheristoo

heavy to be lifted by one

person. Obtain assistance

from others before lifting.





10







1. Place handle assembly (O) onto frame, depress

F

O

the snap buttons, and slide the handle assembly

onto the frame (F) until snap buttons are secured

in place.

CAUTION: Risk of personal injury. Avoid placing

hands between handle and frame when assembling

to prevent pinching.

2. Attach high-pressure

E

P

hose (P) to spray gun.

Make sure it is

secure.

3. Connect wand (E) to

spray gun. Make sure

connection is secure.

4. Thread the side handle (D) into spray

D

gun extension and tighten to desired

position.

5. Place the nozzle holder (B) onto the

panel assembly (A) and push each

nozzle holder into place.

6. Remove the five colored quick-connect

nozzles from the plastic bag and

insert them into

B

A

correct grommet on

the nozzle holder.

Nozzles are color

coded to match

colored nozzles on

panel assembly.

NOTE: The high pressure pump is maintenance free and requires

no oil, if there is a problem with the pump contact a D

eWA LT factory

service center, a D

eWA LT authorized service center or other qualified

service personnel.

WARNING: Risk of bursting.

Use a tire pressure gauge to check the

tires pressure before each use and while inflating tires; see the tire side-

wall for the correct tire pressure.

NOTE: Air tanks, compressors and similar equipment used to inflate

tires can fill small tires similar to these very rapidly. Adjust pressure

regulator on air supply to no more than the rating of the tire pressure.

Add air in small increments and frequently use the tire gauge to

prevent over inflation.





The pressure setting is preset at the factory to achieve op ti mum pres-

sure and cleaning. To lower the pres sure, follow these instructions.

1. Back away from the sur face to be cleaned. The further away you

are, the less the pressure will be on the surface to be cleaned.

2. Change to the 40˚ nozzle (white). This nozzle delivers a less

powerful stream of water and a wider spray pattern. Refer to

Spray Wand Nozzles.

CAUTION: DO NOT attempt to increase pump pressure. A higher

pressure setting than the factory set pressure may damage pump.

3. Reduce the speed of the gasoline engine (RPM). Slow the

engine down and the water pressure will go down with it.



The nozzles for the spray wand are stored in the nozzle holder (B) on

the panel assembly (A). Colors on the panel identify nozzle location

and spray pattern. Refer to the following chart to choose the correct

nozzle for the job to be performed.

11



CHANGING NOZZLES ON SPRAY WAND

DANGER: Risk of fluid injection. Do not direct discharge stream

toward persons, unprotected skin, eyes or any pets or animals.

Serious injury will occur.

WARNING: Flying objects could cause risk of serious injury. DO

NOT attempt to change nozzles while pressure washer is running.

Turn engine off before changing nozzles.

1. Pull quick-connect coupler back and insert

nozzle.

2. Release quick-connect coupler and

twist nozzle to make sure it is secure in

coupler.

WARNING: Flying object could cause risk

of serious injury. Ensure nozzle is completely

inserted in quick-connect socket and quick-

connect snap ring is fully engaged (forward)

before squeezing gun trigger.



Applying chemicals or cleaning solvents is a low-pressure operation.

NOTE: Use only soaps and chemicals designed for pressure washer

use. Do not use bleach.

TO APPLY CHEMICALS AND SOLVENTS

1. Press chemical hose (S) onto barbed fitting

S

located near high pressure hose connection

of pump as shown.

2. Place the other end of chemical hose with

filter on it into the container holding chemi-

cal/cleaning solution.

NOTE: For every 7 gallons (26.5 liters) of

water pumped 1 gallon (3.8 liters) of chemi-

cal/cleaning solution will be used.

Nozzle Color Spray Pattern Uses Surfaces*

Red

0˚ powerful

pinpoint for

very intense

cleaning

metal or

concrete;

DO NOT use

on wood

Yellow

15˚

intense

cleaning of

small areas

metal, concrete

or wood

Green

25

˚

intense

cleaning of

larger areas

metal, concrete

or wood

White

40

˚

covers wide

areas of

cleaning

metal, concrete,

wood or vinyl

Black

low pressure

applies cleaning

solutions

metal, concrete,

wood or vinyl

* CAUTION: The high-pressure spray from your pressure washer

is capable of causing damage to surfaces such as wood, glass,

automobile paint, auto striping and trim, delicate objects such

as flowers and shrubs. Before spraying, check the item to

be cleaned to assure yourself that it is strong enough to resist

damage from the force of spray.

12



3. Install low-pressure (black) nozzle into quick connect fitting of spray

wand, refer to Spray Wand Nozzles.

NOTE: Chemicals and soaps

will not siphon if the black soap nozzle is not installed on the

spray wand.

4. After use of chemicals, place chemical hose into container of clean

water and draw clean water through chemical injection system

to rinse system thoroughly. If chemicals remain in the pump it

could be damaged. Pumps damaged due to chemicals will not be

covered under warranty.



WARNING: To reduce the risk of injury, read the pressure washer

instruction manual and the engine instruction manual before starting

pressure washer.

DANGER: Risk of fluid injection and laceration. When using the

high-pressure setting, DO NOT allow the high-pressure spray to

come in contact with unprotected skin, eyes, or with any pets or

animals. Serious injury will occur.

• Your washer operates at fluid pressures and velocities high

enough to penetrate human and animal flesh, which could result

in amputation or other serious injury. Leaks caused by loose fit-

tings or worn or damaged hoses can result in injection injuries.

DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a

physician immediately!

WARNING: Risk of fire, asphyxiation and burning. NEVER fill fuel

tank when engine is running or hot. Do not smoke when filling fuel

tank.

  fill fuel tank completely. Fill tank to 1/2" (12.7 mm) below

bottom of filler neck to provide space for fuel expansion. Wipe any

fuel spillage from engine and equipment before starting engine.

  run engine in doors or in en closed, poorly ven ti lat ed

areas. En gine exhaust con tains carbon mon ox ide, an odorless

and deadly gas.

 DO NOT let hoses come in contact with very hot engine

muffler during or immediately after use of your pressure

washer. Damage to hoses from contact with hot engine

surfaces will NOT be covered by warranty.

CAUTION: NEVER pull water supply hose to move pres sure washer.

This could damage hose and/or pump inlet.

 DO NOT use hot water, use cold water only.

  turn water supply off while pressure washer engine is

running or damage to pump will result.

 DO NOT stop spraying water for more than

T

two minutes at a time. Pump operates in

bypass mode when spray gun trigger is not

pressed. When the temperature inside the

pump rises too high the thermal relief valve (T)

will open and release a gush of water in an

effort to lower the temperature inside the pump.

The thermal relief valve will then close. If pump is left in bypass

mode for more than two minutes internal components of the

pump can be damaged.

START-UP PROCEDURE

1. In a well-ventilated outdoor area, add fresh, high-quality, unleaded

gasoline with a pump octane rating of 86 or higher. Do not overfill.

Wipe up spilled fuel before starting the engine. Refer to engine

instruction manual for correct procedure.

2. Check engine oil level. Refer to the engine instruction manual for

correct procedure.

3. Connect the water hose to the water source. Turn the water source

on to remove all air from the hose. When a steady stream of water

is present, turn the water source off.

13



4. Verify the filter screen (U) is in water inlet of pump.

U

The cone side faces out.

5. Connect the cold water source (V) to pump inlet.

NOTE: Water source must provide a minimum of

5 gallons per minute at 20 PSI (138 kPa).

WARNING: To reduce the possibility of contami-

nation always protect against backflow when con-

nected to a potable water system.

6. Connect high-pressure hose (P) to pump

V

P

outlet.

7. If applying a chemical or cleaning solution,

refer to Chemicals and Cleaning

Solvents.

8. Turn the water source on.

CAUTION: Risk of property damage. Failure

to do so could cause damage to the pump.

9. Remove all air from the pump and high pressure hose by depress-

ing trigger until a steady stream of water is present.

10. Turn the engine ON/OFF switch (H) to the ON position.

11. Place the fuel valve lever (M) in the ON postion.

12.

If the engine is cold, move the choke (K) to the CLOSED position

as shown.

M

H

K

13. WARNING: Risk of unsafe operation. Pull starter grip slowly

until resistance is felt. Then pull starter grip (I) rapidly to avoid

kickback and prevent hand or arm injury.

NOTE: Do not allow the starter grip to snap back. Return it gently

by hand.

WARNING: Risk of unsafe operation. If engine does not start

after two pulls, squeeze trigger of gun to relieve pump pressure. Pull

starter cord slowly until resistance is felt. Then pull cord rapidly to

avoid kickback and prevent hand or arm injury.

NOTE: If the oil level in the engine is low, the engine will not start.

If the engine does not start, check the oil level and add oil as

needed.

14. As the engine warms up, move the choke to

the OPEN position.

15. Depress trigger on gun to start water flow.

WARNING: Risk of unsafe operation. Stand

on a stable surface and grip gun/wand firmly with

both hands. Expect the gun to kickback when

triggered.

16. Release trigger to stop water flow.

DANGER: Risk of injury from spray. Engage the

X

trigger lock (X) when gun is not in use to prevent

accidental spraying.

17. Adjust spray for the task being performed

by changing quick connect nozzle. Refer to

Spray Wand Nozzles.



1. If chemicals were applied, place the chemical hose into a

container of clean water and draw clean water through chemical

injection system to rinse system thoroughly.

14



CAUTION: Risk of property damage Failure to do so could cause

damage to the pump.

2. Place the engine ON/OFF switch (H) to the OFF Position.

3. Place the fuel valve lever (M) in the OFF

postion.

CAUTION: Risk of property damage. 

turn water supply off while pressure washer

engine is running or damage to pump will result.

4. Turn water source off.

5. Pull trigger on spray gun to relieve any water

pressure in hose or spray gun.

6. Refer to Storage for proper storage procedures.



WARNING: Risk of burning. When performing maintenance, you

may be exposed to hot surfaces, water pressure or moving parts that

can cause serious injury or death.

WARNING: Risk of fire. Always disconnect, spark plug wire, let

the engine cool and release all water pressure before performing

any maintenance or repair. The engine contains flammable fuel. Do

not smoke or work near open flames while performing maintenance.

To ensure efficient operation and longer life of your pressure washer,

a routine maintenance schedule should be prepared and followed.

If the pressure washer is used in unusual conditions, such as high

temperatures or dusty conditions, more fre quent maintenance

checks will be required.



Consult the engine instruction manual for the man u fac tur er's recom-

mendations for any and all maintenance.

NOTE: The pressure washer frame is equipped with an oil drain

hole to help make changing the engine oil easier.



The high pressure pump is maintenance free and requires no oil, if

there is a problem with the pump contact a D

eWA LT factory service

center, a D

eWA LT authorized service center or other qualified ser-

vice personnel.



If the nozzle becomes clogged with foreign materials, such as dirt,

excessive pressure may develop. If the nozzle becomes partially

clogged or restricted, the pump pressure will pulsate. Clean the

nozzle immediately using the nozzle kit supplied and the following

instructions:

1. Shut off the pressure washer and turn off the water supply.

2. Pull trigger on gun handle to relieve any water pressure.

3. Disconnect the spray wand from the gun.

Y

4. Remove the high-pressure nozzle from

the spray wand. Remove any obstructions

with the nozzle cleaning tool (Y) provided

and back flush with clean water.

5. Direct water supply into spray wand to

back flush loosened particles for 30

seconds.

6. Reassemble the nozzle to the wand.

7. Reconnect spray wand to gun then turn on water supply.

8. Start pressure washer and place spray wand into high pressure

setting to test.



This filter screen (U) should be checked periodically and cleaned if

necessary.

15



1. Remove the filter screen (U) by grasping the

U

end and removing it from water inlet of

pump.

2. Clean filter by flushing it with water on both

sides.

3. Reinsert filter into water inlet of pump. Cone

side faces out.

NOTE: Do not operate pressure washer without

ﬁlter properly installed.



1. Using a 1/8" hex head wrench loosen set

screw in hub collar.

2. Slide hub collar from axle and remove the

tire.





Consult the engine instruction manual for the man u fac tur er's

recommendations for storage.



The manufacturer recommends using a pump protector/winter-

izer, such as D

eWALT winterizer (DP80) when storing the unit

for more than 30 days and/or when freezing temperatures are

expected. D

eWALT winterizer (DP80) is availabe at the store

where the pressure washer was purchased. If a pump protector/

winterizer is not available, RV antifreeze can be used as outlined in

the following steps.

NOTE: Using a pump protector/ winterizer or RV antifreeze helps to

provide proper lubrication to the internal seals of the pump regard-

less of temperature or environment.

1. Obtain a funnel, 6 oz. (170 mL) of RV antifreeze and 16–36"

(40–91cm) of garden hose with a male hose connector attached

to one end.

CAUTION:    

other an ti freeze is corrosive and can damage pump.

2. Disconnect spark plug wire.

3. Connect length of garden hose

to water inlet of pump.

4. Add RV antifreeze to hose as

shown.

5. Pull engine starter rope slow-

ly several times until an ti freeze

comes out of high-pressure hose

con nec tion of pump.

6. Remove garden hose from

water inlet of pump.

7. Reconnect spark plug wire.



1. Drain all water from high-

pressure hose, coil it and store it

in cradle of the pressure washer

handle.

2. With nozzle pointed down and

the spray gun and wand in a

vertical position, squeeze trigger

to drain all water from spray gun

and wand. Store in gun holder.

3. Store chemical hose so it is protected from dam age.

4. If space is needed, handles may be removed and attached as

shown.

16



CAUTION: Risk of personal injury. Avoid placing hands between

handle and frame when assembling to prevent pinching.



Recommended accessories for use with your tool are available for

purchase from your local dealer or authorized service center. If you

need assistance in locating any accessory for your tool, please con-

tact D

eWA LT Industrial Tool Co., 701 East Joppa Road, Baltimore,

MD 21286, call 1-800-4-D

eWA LT (1-800-433-9258) or visit our web-

site www.dewalt.com.

DANGER: Risk of fluid injection. When using replacement lances

or guns with this pressure washer, DO NOT use a lance and/or

lance/gun combination that is shorter in length than what was pro-

vided with this pressure washer as measured from the nozzle end

of the lance to the gun trigger.

WARNING: The use of any other accessory not recommended for

use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the pressure washer.



Please have the following information available for all service calls:

Model Number ____________ Serial Number ___________

Date and Place of Purchase ____________________________



To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a D

eWA LT factory service

center, a D

eWA LT authorized service center or other qualified

service personnel. Always use identical replacement parts.



DeWALT pressure washers are warranted for two years from the

date of purchase. D

eWALT will repair, without charge, any defects

due to faulty materials or workmanship. This warranty does not

cover parts that are damaged through misuse or abuse, or parts

which must be replaced from time to time due to normal pressure

washer operation. Normal wear parts include, but are not limited to,

the engine air filter, spark plug, pump valve seals and O rings. This

warranty does not apply to accessories or damage caused where

repairs have been made or attempted by a repair center not autho-

rized by D

eWALT. This warranty gives you specific legal rights and

you may have other rights which vary in certain states or provinces.

For further details of warranty coverage and warranty repair informa-

tion, visit www.dewalt.com and click on Service and Support or call

1-800-4-D

eWALT (1-800-433-9258).

LATIN AMERICA: This warranty does not apply to products sold in

Latin America. For products sold in Latin America, see country spe-

cific warranty information contained either in the packaging, call the

local company or see website for warranty information.

17



FREE WARNING LABEL REPLACEMENT: If your warning labels

(next page) become illegible or are missing, call 1-800-4-D

eWA LT

for a free replacement.



Bypass mode: Allows water to re-circulate within pump when the

gun trigger is not pulled.

Chemical hose: Feeds cleaning agents into the pump to mix with

the water. Refer to Chemicals and Cleaning Solvents.

Chemical injection system: Mixes cleaners or cleaning solvents

with water to improve cleaning effectiveness.

Choke control: Opens and closes carburetor choke valve.

CU: Cleaning Units. GPM multiplied by PSI. (GPM x PSI = CU)

Fuel valve lever: Opens/closes connection between fuel tank and

carburetor.

GPM: Gallons Per Minute. The unit of measure for the flow rate of

water.

PSI: Pounds per Square Inch. The unit of measure for water pres-

sure. Also used for air pressure, hydraulic pressure, etc.

kPa (kilopascal): Metric pressure measurement. 1 kilopascal equal

1000 pascals.

Quick-connect spray wand: Allows the user to quickly change out

high-pressure nozzles. Refer to Spray Wand Nozzles.

Thermal relief valve: When the temperature inside the pump rises

too high the valve will open and release a gush of water in an

effort to lower the temperature inside the pump. The valve will

then close.

Water supply: All pressure washers must have a source of water.

The minimum requirements for a water supply are 20 PSI (138

kPa) and 5 gallons per minute.

18





This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The

operator or maintenance personnel can perform some corrective actions, and others may require the assistance of a qualified D

eWALT

technician or your dealer.

Problem Code

Engine will not start ......................................................................................................1, 2, 3, 4, 5, 6, 7, 8, 29

(refer to the engine's instruction manual for further engine troubleshooting)

No or low pressure (initial use) ......................................................................................9, 10, 11, 12, 13, 14, 15, 16

Will not draw chemicals .................................................................................................16, 17, 18, 19, 20, 22

No or low pressure (after period of normal use) ...........................................................21, 23, 24

Water leaking at gun/spray wand connection ................................................................25, 26

Water leaking at pump ...................................................................................................25, 26, 27, 28

Pump Pulsates ...............................................................................................................12



CODE POSSIBLE CAUSE POSSIBLE SOLUTION

1 No fuel. Add fuel.

2 Low oil. Add required amount of oil.

3 Pressure builds up after two pulls on the recoil starter or after

initial use.

Squeeze gun trigger to relieve pres sure.

4 Choke lever in the NO CHOKE position. Move choke to the CHOKE po si tion.

5 Spark plug wire not attached. Attach spark plug wire.

6 Engine ON/OFF switch in OFF po si tion. Place engine ON/OFF switch in ON position.

7 Choke lever in the CHOKE position on a hot engine or an engine

that has been exposed to thermal heat for a long period of time.

Move choke to the NO CHOKE po si tion.

8 Fuel valve closed. Move the fuel valve lever to the OPEN position.

9 Spray wand not in high pressure. See Spray Wand Nozzles under Operation.

19



CODE POSSIBLE CAUSE POSSIBLE SOLUTION

10 Low water supply. Water supply must be at least 5 GPM @ 20 PSI (138 kPa).

11 Leak at high-pressure hose fitting. Repair leak. Apply sealant tape if necessary.

12 Nozzle obstructed. See Nozzle Cleaning under Maintenance.

13 Water filter screen clogged. Remove and clean filter.

14 Air in hose. Turn off the engine, then the water source. Disconnect the

water source from the pump inlet and turn the water source

on to remove all air from the hose. When there is a steady

stream of water present, turn water source off. Recon nect

water source to pump inlet and turn on wa ter source. Squeeze

trigger to re move re main ing air.

15 Choke lever in the CHOKE position. Move choke to the NO CHOKE po si tion.

16 High-pressure hose is too long. Use high-pressure hose under 100 feet (30.48 m). Lengthen water

supply hose instead of high-pressure hose.

17 Spray wand not in low pressure. See Spray Wand Nozzles under Operation.

18 Chemical filter clogged. Clean filter.

19 Chemical screen not in cleaning solution. Make sure end of chemical hose is fully submerged into cleaning

solution.

20 Chemical too thick. Dilute chemical. Chemical should be the same consistency as water.

21 Worn seal or packing. Have parts cleaned or replaced by authorized service center.

22 Chemical build up in chemical injector. Have replaced by an authorized service center.

23 Worn or obstructed valves. Have replaced by authorized service center.

24 Worn unloader piston. Have replaced by authorized service center.

25 Worn or broken o-ring. Check and replace.

( cont.)

20



( cont.)

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

26 Loose hose connection. Tighten.

27 Piston packings worn. Have replaced by authorized service center.

28 Pump head or tubes damaged from freezing. Have replaced by authorized service center.

29 Air filter filled with oil. Clean air filter element. Refer to engine instruction manual for

correct procedure.

La page charge ...

DeWalt Pressure Washer DPD3100 Manuel utilisateur

Ce manuel convient également à

DeWalt Pressure Washer DPD3100 Manuel utilisateur

dans d''autres langues

Documents connexes