Bercomac 610001 Manuel utilisateur

1

48’’ Snowblower with

Electric Lift

For

CRAFTSMAN TRACTORS

CAUTION:

READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE

OPERATING YOUR EQUIPMENT

M-02

*106024*

* ASSEMBLY

* OPERATION

* MAINTENANCE

* REPAIR PARTS

OWNER’S MANUAL

Model Number

C 151 61001 1

Sears Canada Inc.

Toronto, Ontario

M5B 2B8

106024_EN

2

LIMITED WARRANTY

SEARS CANADA INC.

Toronto, Ontario, M5B 2B8

FOR SERVICE PLEASE CALL

SEARS HOME CENTRAL

1800-4-MY-HOME ®

LIMITED ONE (1) YEAR WARRANTY ON CRAFTSMAN

TRACTOR ATTACHMENTS

For one (1) year from date of purchase, Sears Canada Inc. will repair or replace free of charge at Sears option any

parts which are defective as a result of defective material or faulty workmanship.

COMMERCIAL OR RENTAL USE:

Warranty on Tractor Attachments used for commercial or rental purposes is limited to 90 days.

This warranty does NOT cover:

* Wear items, such as shear pins and shear bolts, belts

* Repairs due to customer abuse or neglect

* Pre-delivery set-up

* In Home service

This warranty is in addition to any statutory warranty and does not exclude or limit legal rights you may have but shall

run concurrently with applicable provincial legislation. Furthermore, some provinces do NOT allow limitation on how

long an implied warranty will last so the above limitations may not apply to you.

Instructions for Obtaining Warranty Services:

Warranty service is available by returning the Craftsman Tractor Attachment to the nearest Sears Service Centre

/Department in Canada. This warranty applies only while this product is in use in Canada.

1

TABLE OF CONTENTS

INTRODUCTION ............................................................................................................................................... 2

SAFETY PRECAUTIONS .................................................................................................................................. 3

SAFETY DECALS .............................................................................................................................................. 5

ASSEMBLY

Tools Required ..................................................................................................................................... 6

Step 1: Subframe Installation ................................................................................................................ 6

Step 2: Installation of the Control Assembly ........................................................................................... 9

Step 3: Drive Mechanism Installation ................................................................................................... 12

Step 4: Snowblower Preparation .......................................................................................................... 15

Step 5: Snowblower Installation ........................................................................................................... 16

Step 6: Installation of Control Box ........................................................................................................ 17

Step 7: Snow Drift Cutters Installation .................................................................................................. 18

Step 8: Rear Counterweight Installation ............................................................................................... 18

Verify Tire Pressure ................................................................................................................. 18

Verify Skid Shoe adjustment ......................................................................................... 18

OPERATION

Snowblower Operation ......................................................................................................................... 19

Controls ................................................................................................................................................ 19

Clearing a Clogged Discharge Chute ................................................................................................... 19

MAINTENANCE

Verify Skid Shoe adjustment .............................................................................................................. 20

Cutting Edge Maintenance ................................................................................................................... 20

Snowblower Pulley Replacement or Alignment ................................................................................... 20

Lubrication ............................................................................................................................................ 20

Augers and Fan Shear Bolt replacement ............................................................................................. 20

Belt Installation, Adjustment, and Replacement ................................................................................... 21

Replacement of one or two sections of the auger and / or gear box ............................................ 22

DISMOUNTING & STORAGE

Snowblower Dismounting ..................................................................................................................... 23

Drive Mechanism Dismounting ............................................................................................................. 23

Storage ................................................................................................................................................. 23

TROUBLESHOOTING ....................................................................................................................................... 24

TORQUE SPECIFICATION TABLE .................................................................................................................. 27

PARTS BREAKDOWN AND PARTS LIST

Chute .................................................................................................................................................. 28

Snowblower .......................................................................................................................................... 30

Northeast Drive Mechanism ................................................................................................................. 34

Subframe .............................................................................................................................................. 36

OPTIONS & ATTACHMENTS ........................................................................................................................... 39

PAGE

2

INTRODUCTION

TO THE PURCHASER

This new accessory was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to

use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will

use this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS

MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.

DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF

HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions

are not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are

not followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are

not followed.

Record your attachment serial number and purchase date in the section reserved below (there is no serial number on

the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement

parts. Use only genuine parts when replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

(IF APPLICABLE)

MODEL NUMBER: ___________________________

PURCHASE DATE : ___________________________

3

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle

and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the accessory.

GLOSSARY:

In this manual, right and left sides are determined by

sitting on the seat of the vehicle facing forward.

In this manual, "accessories" means attachments

(snowblower, rotary broom, blade etc.) that you install

on the vehicle (lawn tractors, A.T.V. s etc).

TRAINING:

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the

accessory’s safety labels to warn of the

possibility of serious injury. Please take

special care in reading and understanding

the safety precautions before operating the

vehicle and accessory.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

vehicle and accessory. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the vehicle nor the

accessory. Never allow adults to operate the vehicle

nor the accessory without proper instructions.

3. No one should operate the vehicle nor the

accessory while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all people,

particularly small children and pets.

PREPARATION:

1. Thoroughly inspect the area where the accessory

is to be used and remove door mats, all foreign

objects and the like.

2. For motorized accessories, disengage all clutches

and shift into neutral before starting engine.

3. Do not operate the accessory without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot engine.

c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner. Always

place containers on the ground, away from your

vehicle, before filling.

e) When practical, remove gas-powered

equipment from the truck or trailer and refuel it

on the ground. If this is not possible, then refuel

such equipment on a trailer with a portable

container, rather than from a gasoline

dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refueling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

6. Let the vehicle and accessory adjust to outdoor

temperatures before using.

7. Never use an accessory without proper guards,

plates, or other safety protective devices in place

8. Always make sure to wear the appropriate safety

equipment required (glasses, muffs, mask…) for

each type of product. See operation section.

9. Always make sure of having safe traction on the

vehicle by using the recommended accessories

(chains, A.T.V. tracks, counterweights…). See

operation section.

10. Always make sure the all components are correctly

installed. (driveline securely attached and locked at

both ends, belts properly installed…)

11. Never modify the accessory or any part without

the written consent from the manufacturer.

4

OPERATION:

1. Do not put hands or feet near, under or inside rotating

parts.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine (motor),

disconnect the wire from the spark plug(s) and keep

wire away to prevent accidental starting. Thoroughly

inspect the accessory for any damage and repair

damage before restarting and using the accessory.

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Take all possible precautions when leaving the

vehicle unattended. Disengage the power take-off,

lower the attachment, place the transmission into

neutral, set the parking brake, stop the engine and

remove the contact key.

6. Do not run the engine indoors, except when starting

the engine and for transporting in or out of the

building. Do not operate or let motor run in a storage

area without ventilation because gas contains

carbon monoxide which is odorless, colorless and

can cause death.

7. Never use the accessories across the face of

slopes, go from top to bottom. Exercise extreme

caution when using equipment on slopes. Do not

attempt to clear a steep slope.

8. Never tolerate bystanders in the working zone.

Never use an accessory in the direction of

bystanders, it might throw gravel or debris that can

hurt people or damage property.

9. Never operate the accessory at high transport

speeds on slippery surfaces. Use care when

backing up.

10. Do not carry passengers.

11. Disengage power to the accessory when it is

transported or not in use.

12. Never operate the accessory without good visibility

or light.

13. Keep the accessory away from heat sources or

flames.

MAINTENANCE AND STORAGE

1. When cleaning, repairing or inspecting the vehicle

and accessory, make certain that all moving parts

have stopped. For gasoline engine, disconnect wire

from the spark plug(s) and keep wire away to

prevent accidental starting.

2. Check all the bolts and components at frequent

intervals to make sure that they are properly

tightened.

3. Never store a motorized accessory with fuel in the

fuel tank inside a building where ignition sources are

present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to cool

before storing in any enclosure.

4. Always refer to the owner’s manual when you store

the accessory and vehicle for a prolonged or an

unspecified length of time.

5. Maintain or replace safety and instruction labels, as

necessary.

6 For winter accessories, (if applicable), let the engine

run for a few minutes after clean snow in order to

prevent the rotary parts from freezing.

7. Inspect the vehicle’s and accessory’s air filter (if

applicable) every day. Clean it or replace it as

necessary. Change the oil more often when working

in dusty conditions. See the vehicle’s and

accessory's owner’s manual.

THIS SYMBOL MEANS

DANGER !

BECOME ALERT !

YOUR SAFETY IS INVOLVED !

SAFETY PRECAUTIONS

5

SAFETY DECALS

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

To avoid serious injury:

Keep hands, feet & clothing away from rotating auger

while engine is running.

To avoid serious injury:

Keep hands out of this discharge chute while engine

is running.

To avoid injury from drive belt:

Keep hands, feet & clothing away.

Do not attempt to install or remove drive belt without

reading owner’s manual.

DECAL #105126

DECAL #105128

DECAL #105127

DECAL #105131

Refer to owner’s manual about wearing safety

glasses, ear muffs and mask.

Refer to owner’s manual for use of counter weights,

cat tracks and tire chains.

DECAL #105130

Before installing or using:

Locate, read and make sure to understand all of the

owner’s manual.

DECAL #105133

Failure to observe these instructions could lead to

severe injury or death.

To avoid injury to hands or fingers:

-Always keep hands clear of rope hook loop, ,hook and

fairlead opening during installation , operation and

when spooling in or out.

-Always use extreme caution when handling hook and

rope during spooling operations.

-Always wear heavy leather gloves when handling rope.

-Keep hands away from the hot surface.

6

ASSEMBLY

IMPORTANT: TORQUE ALL BOLTS ACCORDING TO TORQUE SPECIFICATION TABLE WHEN STATED:

TIGHTEN FIRMLY.

THE WINCH KIT IS TO BE USED ONLY TO LIFT BERCO ACCESSORIES, ANY OTHER USE MAY CAUSE

DAMAGE TO THE VEHICLE.

This subframe may be used to install different

attachments (see attachments page). Once installed,

it may remain permanently on your vehicle.

NOTE: It is not necessary to remove mower deck at

this step.

TOOLS REQUIRED:

Wrenches: 5/16, 7/16, 9/16, 1/2, 10mm

Ratchet

Sockets: 9/16, 1/2

Pliers

Square head screwdriver: #2

1 wrench (for the nuts on the battery posts of the

vehicle)

Optional tools according to the year of the

vehicle:

Drill

Bit: 13/32

Punch

Hammer

Bit: 1/2’’ to install the winch control switch.

Please sort out and identify all the hardware before

starting installation. Lists for the hardware bag and for

the box are supplied in each.

Before starting the subframe installation, verify if your

has a tractor heat shield as shown (A-1).

If not, go to the instructions on next page.

A-1

A-2

If the tractor has this shield, you must remove it and

install the new one included in this kit (See picture

below (A-2).

NOTE: If the original heat shield is bolted to the front

of tractor frame, detach the top part (item 1) of the

heat shield (item 2) that is supplied by folding it up

and down along the dotted line.

Be careful not to cut yourself on the sharp edges. For

your safety sand down the sharp edges.

Use the tractor bolts to secure in place.

INSTALLING THE REFLECTORS

IMPORTANT: When operating the tractor with the

front mounted attachment, install the two red-colored

adhesive reflectors on the rear vertical surface of the

tractor’s fender.

7

ASSEMBLY

Install the female hitch between the two supports

Install the female hitch (item 1)

# Item Description Action

1 Female hitch Install between the

two supports.

2 Hex bolt 3/8 x 1’’

(qty 4)

Insert as shown.

3 Flange nut 3/8’’

(qty 4)

Tighten all the nuts

firmly.

Install the supports (item 5) on each side of the

vehicle.

Item # Description Action

1 Carriage bolt,

3/8 x 1’’ (qty 6)

Insert as shown.

2 Carriage bolt,

5/16 x 1’’ (qty 2)

Insert as shown.

*3 Flat washer 1/2’’,

(qty 6)

See*

4 Flat washer 7/16’’,

(qty 2)

Insert on

carriage bolt

(item 2)

5 Support

(qty 2)

Install on the

bolts as shown.

6 Flange nut 3/8’’,

(qty 6)

Do not tighten

now.

7 Flange nut 5/16’’,

(qty 2)

Do not tighten

now.

*For tractors with a engine mounting plate use only

two washers. Do not use washer A.

*For tractors without an engine mounting plate use

all three washers.

Install the supports

STEP 1

SUBFRAME INSTALLATION:

Refer to parts breakdown section for parts

identification.

8

NOTE: Use these same instructions for both

sides of tractor.

Manual Clutch: Install the new belt guides (item A)

that are included with the drive mechanism on the

bottom carriage bolt (item 1). Place a 1/2’’ flat washer

(items B & C) over the belt guide and the top carriage

bolt. Continue with the handle support installation.

Electric Clutch: Do not install belt guides. Place a

1/2’’ flat washer (item B) over the bottom carriage

bolt. Continue with the handle support (left side)

installation and cab support (right side).

Install the handle support (item 2) on the left side and

the cab support on the right side as shown.

# Item Description Action

1 Carriage bolt

3/8 x 1’’ (qty 4)

Insert the bolts as

shown.

2 Handle / cab support Install as shown.

**3 Thread cutting screw

3/8 x1’’

See **

4 Flat washer 3/8’’

(qty 4)

Install as shown.

5 Flange nut 3/8’’

(qty 4)

Tighten the nuts.

6 Square head set

screw 5/16 x 1/2’’

Insert in the hole of

the handle.

7 Plastic grommet Insert as shown.

** Use this screw if the bottom hole is threaded.

ASSEMBLY

Install the handle support on left side

Install the cab support on right side

Install the spring (item 1)

# Item Description Action

1 Spring Install the spring

on the frame as

shown.

NOTE: The latch must move freely.

Install the spring as shown

9

ASSEMBLY

Install the winch control switch

STEP 2:

INSTALLATION OF THE WINCH CONTROL

SWITCH

Install the relay (item 1).

#

Item

Description Action

1 Relay Install in an appropriate

area.

2 Metal screw

#12 x 3/4’’ (qty 4)

Secure relay in place.

*3 Nylon tie wrap 8’’

(qty 4)

See *

*If necessary use the nylon tie wraps to secure the

relay in place.

** Install in a sheltered place away from bad weather.

Install the relay

IMPORTANT

To prolong the winch cable’s life, release the winch control switch as soon as the accessory touches the

ground. This will keep the cable from tangling up which causes premature wear.

Before drilling the hole, check behind the dashboard

to make sure there is enough space to install the

switch.

Drill a 1/2’’ hole in the dashboard or an appropriate

place (see reference drawing). Stick the UP/DOWN

decal over the hole for the switch.

Insert the switch in the hole and secure in place with

the rubber boot.

NOTE: It is important to install the switch vertically.

Connect the wires as shown.

When the switch is raised, the winch must lift the

accessory. If you prefer the contrary, invert the green

and black wires.

Connect the wires

Up / Down decal

10

ASSEMBLY

CONNECTING THE WIRES

NOTE: The posts on the relay are identified by

numbers. (1-2-3-4).

Install the wires from the winch on the posts of the

relay.

Red wire (+) on post #3.

Black wire (-) on post #4.

Connect the red wire from the winch (limit switch) with

the green wire from the relay.

Connect the wires

IDENTIFY THE IGNITION WIRE:

Place the clip of the Hi / Low tester on the negative

post (-) on the battery or a metal surface without any

paint.

Turn the ignition key to the position: Accessory.

Insert the tip of the tester in a hole at the back of the

starter (switch) make sure to touch the metal part of

the wire (on most tractors, it is the A1 terminal on the

ignition switch that is used for accessories. Before

connection, verify with HI/LOW tester).

If the tester’s light turns on, turn the ignition key to the

position, Off. The light must turn off.

You have identified the ignition wire, if not repeat the

operation on another wire.

INSTALL THE CONTROL WIRE:

Join the ignition wire and the red wire from the winch

control (item 1) with the instant connector (item 2).

Connect the black wire of the winch control (item 3) to

the black wire on the relay.

Connect the green wire of the winch control (item 3)

with the red wire of the winch (limit switch).

Connect the ignition wire

11

ASSEMBLY

CAUTION

FOR YOUR SECURITY:

Read and follow the safety precautions for the

battery in the vehicle’s manual.

CONNECT THE WIRES ON THE BATTERY:

Connect the wires from the relay to the vehicle’s

battery.

The red wire (+) on the positive post of the battery

(item 1).

The black wire (-) on the negative post of the battery

(item 2).

Make sure to tighten the nuts on the posts.

TIE ALL THE WIRES:

NOTE: Make sure the wires from the control

assembly do not interfere with anything on the tractor

nor come into contact with any heating, electrical or

removable elements of the tractor.

Tie the wires with four nylon tie wraps included in the

kit.

Connect the relay wires to the battery

Install the heat shield

VERY IMPORTANT:

Make sure the cable winds up and unrolls as shown

in the figure (cable under the spool).

If the winch cable does not wind up from the

bottom of spool as shown, the limit switch will not

work and may cause damage to the subframe,

winch and accessory.

Install the heat shield (item 1).

# Item Description Action

1 Heat shield Install as shown.

2 Hex bolts 1/4 x 1/2’’

(qty 2)

Tighten firmly.

NOTE: If the tractor has a front muffler, install the

heat shield (item 3) using the two bolts (item 4)

which holds the winch on the frame.

12

ASSEMBLY

STEP 3:

DRIVE MECHANISM INSTALLATION: WARNING

TO PREVENT INJURIES:

It is the person who installs the drive mechanism

responsibility to make sure that when the clutch

is disengaged that all moving parts stop.

For more information, do not hesitate to contact

the technical support.

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

NOTE: You must remove mower deck to install

the drive mechanism.

Install the support (item 2) on each side.

# Item Description Action

1 Carriage bolt

3/8 x 3/4’’ (qty 4)

Insert as shown.

2 Support (qty 2) See*

3 Flange nut 3/8’’

(qty 4)

Tighten firmly.

*Choose the appropriate holes in the supports and

make sure that there is no interference between the

pin and the parts of the vehicle. Install the supports

The next two instructions are for vehicles

that do not have pins that are used as

supports for the mower deck.

Use the drilling template to drill a hole on each side of

the vehicle.

Drill a hole if applicable

Install the sleeves

Install the sleeve (item 1) on each side.

# Item Description Action

1 Sleeve (qty 2) Install as shown.

2 Hex bolt 3/8 x 1

1/4’’ (qty 2)

Insert in the sleeve.

3 Flange nut 3/8’’

(qty 2)

Tighten firmly.

13

ASSEMBLY

For tractors with Electric Clutch:

Install the belt on the engine pulley of the vehicle.

Check the tension on the spring.

If necessary, adjust the tension by moving the

adjustment rod (item 1) and tighten the set screw

(item 2).

No modifications to be done

Install the drive mechanism

Install the drive mechanism (item 1).

# Item Description Action

1 The front end of drive

mechanism

Hook on the pins.

2 The back end of

drive mechanism

Install between the

supports.

3 Pin Insert as shown.

*See note.

4 Hair pin Secure the pin.

*NOTE: If the pin (item 3) is difficult to slide in the

supports, loosen the nuts ( item A).

*For tractors with a 5 1/2’’ engine pulley:

A shorter drive belt may be necessary to achieve the

proper tension.

Belt A-51 (105190) instead of a A-52 (104847) or

Belt A-55 (105191) instead of a A-56 (104848)

14

IMPORTANT: Adjust the height of the three supports

(items 1, 2 and 3) to make sure the drive mechanism

pulley (item 4) is aligned with the engine pulley (item

5) more or less 1/8’’.

If applicable, you can remove or add a flat washer on

the tension pulley (item 6) for a better adjustment.

Engage and disengage the clutch a few times and

make sure the belt does not touch the belt guide in

any place when the drive mechanism is engaged.

VERIFICATION OF THE BELT AND PULLEY

ALIGNMENT:

Adjust the pulleys

For tractors with Manual Clutch activated by a cable:

Install the tractor’s manual clutch cable .

* Remove the spring.

# Item Description Action

1 Spring from the

clutch cable

Install as shown in the hole

on the tension pulley.

2 Clutch cable Insert in the slot on the

adjustment rod.

3 Hair pin 2mm Secure the cable.

4 Adjustment rod Slide towards the back to

apply enough tension on the

spring.*

5 Square head set

screw 5/16 x 1/2’’

Secure the adjustment rod.

Install the belt on the engine pulley of the vehicle.

Check the tension on the spring.

If necessary, adjust the tension by moving the

adjustment rod and tighten the set screw.

Install the manual clutch cable

Adjust the supports

*For tractors with a 5 1/2’’ engine pulley:

A shorter drive belt may be necessary to achieve the

proper tension.

Belt A-51 (105190) instead of a A-52 (104847) or

Belt A-55 (105191) instead of a A-56 (104848)

WARNING

TO PREVENT INJURIES:

do this verification when the engine of the vehicle

is not running.

WARNING

TO PREVENT INJURIES:

It is the person who installs the drive mechanism

responsibility to make sure that when the clutch

is disengaged that all moving parts stop.

For more information, do not hesitate to contact

the technical support.

ASSEMBLY

15

ASSEMBLY

TOOLS REQUIRED:

2 Wrenches, 1/4’’

STEP 4

SNOWBLOWER PREPARATION:

Refer to parts breakdown section for parts

identification.

Install the chute (item 2).

Item # Description Action

1 Rotation ring Install over opening as

shown.

2 Chute Place as shown, turn to

lock into place.

Install chute

Install the motor assembly (item 3).

Item # Description Action

1 Carriage bolts

1/4" n.c. x 1" (qty 2)

Insert inside the

chute as shown.

2 Support Install on the bolts.

3 Motor assembly Install on the bolts

and under support.

4 Flange nuts 1/4’’

(qty 2)

Secure everything

in place.

NOTE: Make sure the pin (item 5) on the electric

motor is well inserted in the hole on the support.

Install motor assembly

16

INSTALLATION

STEP 5

SNOWBLOWER INSTALLATION:

You must install the subframe and drive mechanism

before continuing to install the snowblower.

Attach the snowblower to the subframe as shown.

Make sure the snowblower is pushed in until locked

into place by the lock (item 1).

Install belts.

NOTE: See the belt installation instructions in the

Maintenance section.

Insert the snowblower in the lock.

Install the cable

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

CAUTION

The belt tension arm & needs to be held firmly while

displacing to prevent injury.

CAUTION

Never use the snowblower without the belt guard.

After installing the belt, hook the winch cable (item 1)

to the hook (item 2) and secure with a 2.5mm hair pin

(item 3).

Familiarize yourself with the winch control and make

sure the cable stays wrapped from the bottom of the

drum of the winch. See picture of the winch in the

subframe section.

Lift and lower the snowblower using the switch.

When lowering the accessory, release the switch of

the winch control as soon as the accessory touches

the ground.

17

ASSEMBLY

STEP 6

INSTALLATION OF THE CONTROL BOX:

NOTE: Before choosing the ideal place to install the

control support (item 1) and control box, connect the

control box wires to the motors and to the battery (see

instructions below).

Use the joystick to determine which direction activates

which motor.

We suggest putting the control box on the right fender of

the tractor close to the driver’s seat or close to the

steering wheel according to your preference.

Secure the control support with two 1/4 x 3/4" bolts and

flange nuts.

Install the control box on the support.

Determine direction of joystick and position of control

box before installing the support.

Thread the wires on the frame to the front where they

will not be seen and where they won’t touch any hot or

moving parts.

Attach to the vehicle’s frame using the tie wraps.

NOTE: It is recommended to place the wire connectors

as close as possible to the subframe. Secure the wires

in an adequate place in order to separate the accessory

from the vehicle when storing.

Connect the wires to the electric motors. The longest

wires are connected to the deflector motor.

Connect the red wire to the positive battery post and

the black wire to the negative battery post.

Connect the wires to the motors and battery.

18

ASSEMBLY

Turn the chute to its maximum towards the right and

lower the deflector.

Secure the wire for the deflector motor (item 1) with a tie

wrap around the motor.

Tie the wire for the deflector with another tie wrap in the

hole (item 3) at the base of the deflector as shown.

Secure the wires for the rotation motor (item 2) with a tie

wrap.

Be sure to leave enough wire length to be able to turn

the chute.

Secure wires on the motors

STEP 7

SNOW DRIFT CUTTERS INSTALLATION:

Refer to parts breakdown included in the box for the

drift cutters for parts identification.

Please follow the instructions included in the box for

the Snow Drift Cutters #700260.

This kit is included with the snowblower.

STEP 8

REAR COUNTERWEIGHT

INSTALLATION:

Refer to parts breakdown included in the box for the

Rear Counterweights for parts identification.

Please follow the instructions included in the box for

the Rear Counterweights #700246-5.

This kit is included with the snowblower.

Install drift cutters

Install counterweights

Adjust skid shoes

VERIFY TIRE PRESSURE:

Tire pressure must be even on both sides of tractor

according to the owner’s manual of the vehicle.

VERIFY SKID SHOE ADJUSTMENT:

LEVEL PAVED SURFACE: Adjust skid shoes to allow

3/16" to 1/4" or 5mm to 7mm clearance (A) between

cutting edge and surface.

UNEVEN OR GRAVEL SURFACE: Adjust skid shoes

to allow 1/2" to 5/8" or 13mm to 16mm clearance (A)

between cutting edge and surface.

La page charge ...

Bercomac 610001 Manuel utilisateur

Bercomac 610001 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents