Bercomac 610001 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur
1
48’’ Snowblower with
Electric Lift
For
CRAFTSMAN TRACTORS
CAUTION:
READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE
OPERATING YOUR EQUIPMENT
M-02
*106024*
* ASSEMBLY
* OPERATION
* MAINTENANCE
* REPAIR PARTS
OWNER’S MANUAL
Model Number
C 151 61001 1
Sears Canada Inc.
Toronto, Ontario
M5B 2B8
106024_EN
2
LIMITED WARRANTY
SEARS CANADA INC.
Toronto, Ontario, M5B 2B8
FOR SERVICE PLEASE CALL
SEARS HOME CENTRAL
1800-4-MY-HOME ®
LIMITED ONE (1) YEAR WARRANTY ON CRAFTSMAN
TRACTOR ATTACHMENTS
For one (1) year from date of purchase, Sears Canada Inc. will repair or replace free of charge at Sears option any
parts which are defective as a result of defective material or faulty workmanship.
COMMERCIAL OR RENTAL USE:
Warranty on Tractor Attachments used for commercial or rental purposes is limited to 90 days.
This warranty does NOT cover:
* Wear items, such as shear pins and shear bolts, belts
* Repairs due to customer abuse or neglect
* Pre-delivery set-up
* In Home service
This warranty is in addition to any statutory warranty and does not exclude or limit legal rights you may have but shall
run concurrently with applicable provincial legislation. Furthermore, some provinces do NOT allow limitation on how
long an implied warranty will last so the above limitations may not apply to you.
Instructions for Obtaining Warranty Services:
Warranty service is available by returning the Craftsman Tractor Attachment to the nearest Sears Service Centre
/Department in Canada. This warranty applies only while this product is in use in Canada.
1
TABLE OF CONTENTS
INTRODUCTION ............................................................................................................................................... 2
SAFETY PRECAUTIONS .................................................................................................................................. 3
SAFETY DECALS .............................................................................................................................................. 5
ASSEMBLY
Tools Required ..................................................................................................................................... 6
Step 1: Subframe Installation ................................................................................................................ 6
Step 2: Installation of the Control Assembly ........................................................................................... 9
Step 3: Drive Mechanism Installation ................................................................................................... 12
Step 4: Snowblower Preparation .......................................................................................................... 15
Step 5: Snowblower Installation ........................................................................................................... 16
Step 6: Installation of Control Box ........................................................................................................ 17
Step 7: Snow Drift Cutters Installation .................................................................................................. 18
Step 8: Rear Counterweight Installation ............................................................................................... 18
Verify Tire Pressure ................................................................................................................. 18
Verify Skid Shoe adjustment ......................................................................................... 18
OPERATION
Snowblower Operation ......................................................................................................................... 19
Controls ................................................................................................................................................ 19
Clearing a Clogged Discharge Chute ................................................................................................... 19
MAINTENANCE
Verify Skid Shoe adjustment .............................................................................................................. 20
Cutting Edge Maintenance ................................................................................................................... 20
Snowblower Pulley Replacement or Alignment ................................................................................... 20
Lubrication ............................................................................................................................................ 20
Augers and Fan Shear Bolt replacement ............................................................................................. 20
Belt Installation, Adjustment, and Replacement ................................................................................... 21
Replacement of one or two sections of the auger and / or gear box ............................................ 22
DISMOUNTING & STORAGE
Snowblower Dismounting ..................................................................................................................... 23
Drive Mechanism Dismounting ............................................................................................................. 23
Storage ................................................................................................................................................. 23
TROUBLESHOOTING ....................................................................................................................................... 24
TORQUE SPECIFICATION TABLE .................................................................................................................. 27
PARTS BREAKDOWN AND PARTS LIST
Chute .................................................................................................................................................. 28
Snowblower .......................................................................................................................................... 30
Northeast Drive Mechanism ................................................................................................................. 34
Subframe .............................................................................................................................................. 36
OPTIONS & ATTACHMENTS ........................................................................................................................... 39
PAGE
2
INTRODUCTION
TO THE PURCHASER
This new accessory was carefully designed to give years of dependable service. This manual has been provided to
assist in the safe operation and servicing of your attachment.
NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but
are intended for reference only and are based on the latest product information available at the time of publication.
Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to
use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will
use this attachment.
THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS
MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.
DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF
HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.
DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions
are not followed.
WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are
not followed.
CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are
not followed.
Record your attachment serial number and purchase date in the section reserved below (there is no serial number on
the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement
parts. Use only genuine parts when replacements are required.
If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer
for warranty service.
This manual should be kept for future reference.
Please check if you have received all the parts for your kit with the list of the
bag and the list of the box.
3
SAFETY PRECAUTIONS
Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle
and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the
following safety instructions could result in serious injury. All operators, no matter how experienced they may be,
should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal
obligation to instruct all operators in safe operation of the accessory.
GLOSSARY:
In this manual, right and left sides are determined by
sitting on the seat of the vehicle facing forward.
In this manual, "accessories" means attachments
(snowblower, rotary broom, blade etc.) that you install
on the vehicle (lawn tractors, A.T.V. s etc).
TRAINING:
This symbol, "Safety Alert Symbol", is used
throughout this manual and on the
accessory’s safety labels to warn of the
possibility of serious injury. Please take
special care in reading and understanding
the safety precautions before operating the
vehicle and accessory.
1. Read this owner's manual carefully. Be thoroughly
familiar with the controls and proper use of the
vehicle and accessory. Know how to stop the unit
and disengage the controls quickly.
2. Never allow children to operate the vehicle nor the
accessory. Never allow adults to operate the vehicle
nor the accessory without proper instructions.
3. No one should operate the vehicle nor the
accessory while intoxicated or while taking
medication that impairs the senses or reactions.
4. Keep the area of operation clear of all people,
particularly small children and pets.
PREPARATION:
1. Thoroughly inspect the area where the accessory
is to be used and remove door mats, all foreign
objects and the like.
2. For motorized accessories, disengage all clutches
and shift into neutral before starting engine.
3. Do not operate the accessory without wearing
adequate winter outer garments. Avoid loose fitting
clothing that can get caught in moving parts. Wear
footwear that will improve footing on slippery
surfaces.
4. Handle fuel with care, it is highly flammable.
a) Use approved fuel container.
b) Never add fuel to a running engine or hot engine.
c) Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors.
d) Never fill containers inside a vehicle, or on a
truck or a trailer bed with a plastic liner. Always
place containers on the ground, away from your
vehicle, before filling.
e) When practical, remove gas-powered
equipment from the truck or trailer and refuel it
on the ground. If this is not possible, then refuel
such equipment on a trailer with a portable
container, rather than from a gasoline
dispenser nozzle.
f) Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times, until
refueling is complete. Do not use a nozzle lock-
open device.
g) Replace fuel cap securely and wipe up spilled
fuel.
h) If fuel is spilled on clothing, change clothing
immediately.
5. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by manufacturer).
6. Let the vehicle and accessory adjust to outdoor
temperatures before using.
7. Never use an accessory without proper guards,
plates, or other safety protective devices in place
8. Always make sure to wear the appropriate safety
equipment required (glasses, muffs, mask…) for
each type of product. See operation section.
9. Always make sure of having safe traction on the
vehicle by using the recommended accessories
(chains, A.T.V. tracks, counterweights). See
operation section.
10. Always make sure the all components are correctly
installed. (driveline securely attached and locked at
both ends, belts properly installed…)
11. Never modify the accessory or any part without
the written consent from the manufacturer.
4
OPERATION:
1. Do not put hands or feet near, under or inside rotating
parts.
2. Exercise extreme caution when operating on or
crossing gravel drives, walks or roads. Stay alert for
hidden hazards or traffic. Do not carry passengers.
3. After striking a foreign object, stop the engine (motor),
disconnect the wire from the spark plug(s) and keep
wire away to prevent accidental starting. Thoroughly
inspect the accessory for any damage and repair
damage before restarting and using the accessory.
4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the
cause. Vibration is generally a warning of trouble.
5. Take all possible precautions when leaving the
vehicle unattended. Disengage the power take-off,
lower the attachment, place the transmission into
neutral, set the parking brake, stop the engine and
remove the contact key.
6. Do not run the engine indoors, except when starting
the engine and for transporting in or out of the
building. Do not operate or let motor run in a storage
area without ventilation because gas contains
carbon monoxide which is odorless, colorless and
can cause death.
7. Never use the accessories across the face of
slopes, go from top to bottom. Exercise extreme
caution when using equipment on slopes. Do not
attempt to clear a steep slope.
8. Never tolerate bystanders in the working zone.
Never use an accessory in the direction of
bystanders, it might throw gravel or debris that can
hurt people or damage property.
9. Never operate the accessory at high transport
speeds on slippery surfaces. Use care when
backing up.
10. Do not carry passengers.
11. Disengage power to the accessory when it is
transported or not in use.
12. Never operate the accessory without good visibility
or light.
13. Keep the accessory away from heat sources or
flames.
MAINTENANCE AND STORAGE
1. When cleaning, repairing or inspecting the vehicle
and accessory, make certain that all moving parts
have stopped. For gasoline engine, disconnect wire
from the spark plug(s) and keep wire away to
prevent accidental starting.
2. Check all the bolts and components at frequent
intervals to make sure that they are properly
tightened.
3. Never store a motorized accessory with fuel in the
fuel tank inside a building where ignition sources are
present such as hot water and space heaters,
clothes dryers, and the like. Allow the engine to cool
before storing in any enclosure.
4. Always refer to the owner’s manual when you store
the accessory and vehicle for a prolonged or an
unspecified length of time.
5. Maintain or replace safety and instruction labels, as
necessary.
6 For winter accessories, (if applicable), let the engine
run for a few minutes after clean snow in order to
prevent the rotary parts from freezing.
7. Inspect the vehicle’s and accessory’s air filter (if
applicable) every day. Clean it or replace it as
necessary. Change the oil more often when working
in dusty conditions. See the vehicle’s and
accessory's owner’s manual.
THIS SYMBOL MEANS
DANGER !
BECOME ALERT !
YOUR SAFETY IS INVOLVED !
SAFETY PRECAUTIONS
5
SAFETY DECALS
REPLACE IF DECALS ARE DAMAGED
SEE PARTS BREAKDOWN FOR DECAL LOCATION
To avoid serious injury:
Keep hands, feet & clothing away from rotating auger
while engine is running.
To avoid serious injury:
Keep hands out of this discharge chute while engine
is running.
To avoid injury from drive belt:
Keep hands, feet & clothing away.
Do not attempt to install or remove drive belt without
reading owner’s manual.
DECAL #105126
DECAL #105128
DECAL #105127
DECAL #105131
Refer to owner’s manual about wearing safety
glasses, ear muffs and mask.
Refer to owner’s manual for use of counter weights,
cat tracks and tire chains.
DECAL #105130
Before installing or using:
Locate, read and make sure to understand all of the
owner’s manual.
DECAL #105133
Failure to observe these instructions could lead to
severe injury or death.
To avoid injury to hands or fingers:
-Always keep hands clear of rope hook loop, ,hook and
fairlead opening during installation , operation and
when spooling in or out.
-Always use extreme caution when handling hook and
rope during spooling operations.
-Always wear heavy leather gloves when handling rope.
-Keep hands away from the hot surface.
6
ASSEMBLY
IMPORTANT: TORQUE ALL BOLTS ACCORDING TO TORQUE SPECIFICATION TABLE WHEN STATED:
TIGHTEN FIRMLY.
THE WINCH KIT IS TO BE USED ONLY TO LIFT BERCO ACCESSORIES, ANY OTHER USE MAY CAUSE
DAMAGE TO THE VEHICLE.
This subframe may be used to install different
attachments (see attachments page). Once installed,
it may remain permanently on your vehicle.
NOTE: It is not necessary to remove mower deck at
this step.
TOOLS REQUIRED:
Wrenches: 5/16, 7/16, 9/16, 1/2, 10mm
Ratchet
Sockets: 9/16, 1/2
Pliers
Square head screwdriver: #2
1 wrench (for the nuts on the battery posts of the
vehicle)
Optional tools according to the year of the
vehicle:
Drill
Bit: 13/32
Punch
Hammer
Bit: 1/2’’ to install the winch control switch.
Please sort out and identify all the hardware before
starting installation. Lists for the hardware bag and for
the box are supplied in each.
Before starting the subframe installation, verify if your
has a tractor heat shield as shown (A-1).
If not, go to the instructions on next page.
A-1
A-2
If the tractor has this shield, you must remove it and
install the new one included in this kit (See picture
below (A-2).
NOTE: If the original heat shield is bolted to the front
of tractor frame, detach the top part (item 1) of the
heat shield (item 2) that is supplied by folding it up
and down along the dotted line.
Be careful not to cut yourself on the sharp edges. For
your safety sand down the sharp edges.
Use the tractor bolts to secure in place.
INSTALLING THE REFLECTORS
IMPORTANT: When operating the tractor with the
front mounted attachment, install the two red-colored
adhesive reflectors on the rear vertical surface of the
tractor’s fender.
7
ASSEMBLY
Install the female hitch between the two supports
Install the female hitch (item 1)
# Item Description Action
1 Female hitch Install between the
two supports.
2 Hex bolt 3/8 x 1’’
(qty 4)
Insert as shown.
3 Flange nut 3/8’
(qty 4)
Tighten all the nuts
firmly.
Install the supports (item 5) on each side of the
vehicle.
Item # Description Action
1 Carriage bolt,
3/8 x 1’’ (qty 6)
Insert as shown.
2 Carriage bolt,
5/16 x 1’’ (qty 2)
Insert as shown.
*3 Flat washer 1/2’’,
(qty 6)
See*
4 Flat washer 7/16’’,
(qty 2)
Insert on
carriage bolt
(item 2)
5 Support
(qty 2)
Install on the
bolts as shown.
6 Flange nut 3/8’’,
(qty 6)
Do not tighten
now.
7 Flange nut 5/16’’,
(qty 2)
Do not tighten
now.
*For tractors with a engine mounting plate use only
two washers. Do not use washer A.
*For tractors without an engine mounting plate use
all three washers.
Install the supports
STEP 1
SUBFRAME INSTALLATION:
Refer to parts breakdown section for parts
identification.
8
NOTE: Use these same instructions for both
sides of tractor.
Manual Clutch: Install the new belt guides (item A)
that are included with the drive mechanism on the
bottom carriage bolt (item 1). Place a 1/2’flat washer
(items B & C) over the belt guide and the top carriage
bolt. Continue with the handle support installation.
Electric Clutch: Do not install belt guides. Place a
1/2’’ flat washer (item B) over the bottom carriage
bolt. Continue with the handle support (left side)
installation and cab support (right side).
Install the handle support (item 2) on the left side and
the cab support on the right side as shown.
# Item Description Action
1 Carriage bolt
3/8 x 1’’ (qty 4)
Insert the bolts as
shown.
2 Handle / cab support Install as shown.
**3 Thread cutting screw
3/8 x1’’
See **
4 Flat washer 3/8’’
(qty 4)
Install as shown.
5 Flange nut 3/8’
(qty 4)
Tighten the nuts.
6 Square head set
screw 5/16 x 1/2’’
Insert in the hole of
the handle.
7 Plastic grommet Insert as shown.
** Use this screw if the bottom hole is threaded.
ASSEMBLY
Install the handle support on left side
Install the cab support on right side
Install the spring (item 1)
# Item Description Action
1 Spring Install the spring
on the frame as
shown.
NOTE: The latch must move freely.
Install the spring as shown
9
ASSEMBLY
Install the winch control switch
STEP 2:
INSTALLATION OF THE WINCH CONTROL
SWITCH
Install the relay (item 1).
#
Item
Description Action
1 Relay Install in an appropriate
area.
2 Metal screw
#12 x 3/4’’ (qty 4)
Secure relay in place.
*3 Nylon tie wrap 8’
(qty 4)
See *
*If necessary use the nylon tie wraps to secure the
relay in place.
** Install in a sheltered place away from bad weather.
Install the relay
IMPORTANT
To prolong the winch cable’s life, release the winch control switch as soon as the accessory touches the
ground. This will keep the cable from tangling up which causes premature wear.
Before drilling the hole, check behind the dashboard
to make sure there is enough space to install the
switch.
Drill a 1/2’’ hole in the dashboard or an appropriate
place (see reference drawing). Stick the UP/DOWN
decal over the hole for the switch.
Insert the switch in the hole and secure in place with
the rubber boot.
NOTE: It is important to install the switch vertically.
Connect the wires as shown.
When the switch is raised, the winch must lift the
accessory. If you prefer the contrary, invert the green
and black wires.
Connect the wires
Up / Down decal
10
ASSEMBLY
CONNECTING THE WIRES
NOTE: The posts on the relay are identified by
numbers. (1-2-3-4).
Install the wires from the winch on the posts of the
relay.
Red wire (+) on post #3.
Black wire (-) on post #4.
Connect the red wire from the winch (limit switch) with
the green wire from the relay.
Connect the wires
IDENTIFY THE IGNITION WIRE:
Place the clip of the Hi / Low tester on the negative
post (-) on the battery or a metal surface without any
paint.
Turn the ignition key to the position: Accessory.
Insert the tip of the tester in a hole at the back of the
starter (switch) make sure to touch the metal part of
the wire (on most tractors, it is the A1 terminal on the
ignition switch that is used for accessories. Before
connection, verify with HI/LOW tester).
If the tester’s light turns on, turn the ignition key to the
position, Off. The light must turn off.
You have identified the ignition wire, if not repeat the
operation on another wire.
INSTALL THE CONTROL WIRE:
Join the ignition wire and the red wire from the winch
control (item 1) with the instant connector (item 2).
Connect the black wire of the winch control (item 3) to
the black wire on the relay.
Connect the green wire of the winch control (item 3)
with the red wire of the winch (limit switch).
Connect the ignition wire
11
ASSEMBLY
CAUTION
FOR YOUR SECURITY:
Read and follow the safety precautions for the
battery in the vehicle’s manual.
CONNECT THE WIRES ON THE BATTERY:
Connect the wires from the relay to the vehicle’s
battery.
The red wire (+) on the positive post of the battery
(item 1).
The black wire (-) on the negative post of the battery
(item 2).
Make sure to tighten the nuts on the posts.
TIE ALL THE WIRES:
NOTE: Make sure the wires from the control
assembly do not interfere with anything on the tractor
nor come into contact with any heating, electrical or
removable elements of the tractor.
Tie the wires with four nylon tie wraps included in the
kit.
Connect the relay wires to the battery
Install the heat shield
VERY IMPORTANT:
Make sure the cable winds up and unrolls as shown
in the figure (cable under the spool).
If the winch cable does not wind up from the
bottom of spool as shown, the limit switch will not
work and may cause damage to the subframe,
winch and accessory.
Install the heat shield (item 1).
# Item Description Action
1 Heat shield Install as shown.
2 Hex bolts 1/4 x 1/2’’
(qty 2)
Tighten firmly.
NOTE: If the tractor has a front muffler, install the
heat shield (item 3) using the two bolts (item 4)
which holds the winch on the frame.
12
ASSEMBLY
STEP 3:
DRIVE MECHANISM INSTALLATION: WARNING
TO PREVENT INJURIES:
It is the person who installs the drive mechanism
responsibility to make sure that when the clutch
is disengaged that all moving parts stop.
For more information, do not hesitate to contact
the technical support.
WARNING
TO PREVENT INJURIES:
Stop the motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
NOTE: You must remove mower deck to install
the drive mechanism.
Install the support (item 2) on each side.
# Item Description Action
1 Carriage bolt
3/8 x 3/4’’ (qty 4)
Insert as shown.
2 Support (qty 2) See*
3 Flange nut 3/8’
(qty 4)
Tighten firmly.
*Choose the appropriate holes in the supports and
make sure that there is no interference between the
pin and the parts of the vehicle. Install the supports
The next two instructions are for vehicles
that do not have pins that are used as
supports for the mower deck.
Use the drilling template to drill a hole on each side of
the vehicle.
Drill a hole if applicable
Install the sleeves
Install the sleeve (item 1) on each side.
# Item Description Action
1 Sleeve (qty 2) Install as shown.
2 Hex bolt 3/8 x 1
1/4’’ (qty 2)
Insert in the sleeve.
3 Flange nut 3/8’
(qty 2)
Tighten firmly.
13
ASSEMBLY
For tractors with Electric Clutch:
Install the belt on the engine pulley of the vehicle.
Check the tension on the spring.
If necessary, adjust the tension by moving the
adjustment rod (item 1) and tighten the set screw
(item 2).
No modifications to be done
Install the drive mechanism
Install the drive mechanism (item 1).
# Item Description Action
1 The front end of drive
mechanism
Hook on the pins.
2 The back end of
drive mechanism
Install between the
supports.
3 Pin Insert as shown.
*See note.
4 Hair pin Secure the pin.
*NOTE: If the pin (item 3) is difficult to slide in the
supports, loosen the nuts ( item A).
*For tractors with a 5 1/2’ engine pulley:
A shorter drive belt may be necessary to achieve the
proper tension.
Belt A-51 (105190) instead of a A-52 (104847) or
Belt A-55 (105191) instead of a A-56 (104848)
14
IMPORTANT: Adjust the height of the three supports
(items 1, 2 and 3) to make sure the drive mechanism
pulley (item 4) is aligned with the engine pulley (item
5) more or less 1/8’’.
If applicable, you can remove or add a flat washer on
the tension pulley (item 6) for a better adjustment.
Engage and disengage the clutch a few times and
make sure the belt does not touch the belt guide in
any place when the drive mechanism is engaged.
VERIFICATION OF THE BELT AND PULLEY
ALIGNMENT:
Adjust the pulleys
For tractors with Manual Clutch activated by a cable:
Install the tractor’s manual clutch cable .
* Remove the spring.
# Item Description Action
1 Spring from the
clutch cable
Install as shown in the hole
on the tension pulley.
2 Clutch cable Insert in the slot on the
adjustment rod.
3 Hair pin 2mm Secure the cable.
4 Adjustment rod Slide towards the back to
apply enough tension on the
spring.*
5 Square head set
screw 5/16 x 1/2’’
Secure the adjustment rod.
Install the belt on the engine pulley of the vehicle.
Check the tension on the spring.
If necessary, adjust the tension by moving the
adjustment rod and tighten the set screw.
Install the manual clutch cable
Adjust the supports
*For tractors with a 5 1/2’ engine pulley:
A shorter drive belt may be necessary to achieve the
proper tension.
Belt A-51 (105190) instead of a A-52 (104847) or
Belt A-55 (105191) instead of a A-56 (104848)
WARNING
TO PREVENT INJURIES:
do this verification when the engine of the vehicle
is not running.
WARNING
TO PREVENT INJURIES:
It is the person who installs the drive mechanism
responsibility to make sure that when the clutch
is disengaged that all moving parts stop.
For more information, do not hesitate to contact
the technical support.
ASSEMBLY
15
ASSEMBLY
TOOLS REQUIRED:
2 Wrenches, 1/4’
STEP 4
SNOWBLOWER PREPARATION:
Refer to parts breakdown section for parts
identification.
Install the chute (item 2).
Item # Description Action
1 Rotation ring Install over opening as
shown.
2 Chute Place as shown, turn to
lock into place.
Install chute
Install the motor assembly (item 3).
Item # Description Action
1 Carriage bolts
1/4" n.c. x 1" (qty 2)
Insert inside the
chute as shown.
2 Support Install on the bolts.
3 Motor assembly Install on the bolts
and under support.
4 Flange nuts 1/4’
(qty 2)
Secure everything
in place.
NOTE: Make sure the pin (item 5) on the electric
motor is well inserted in the hole on the support.
Install motor assembly
16
INSTALLATION
STEP 5
SNOWBLOWER INSTALLATION:
You must install the subframe and drive mechanism
before continuing to install the snowblower.
Attach the snowblower to the subframe as shown.
Make sure the snowblower is pushed in until locked
into place by the lock (item 1).
Install belts.
NOTE: See the belt installation instructions in the
Maintenance section.
Insert the snowblower in the lock.
Install the cable
WARNING
TO PREVENT INJURIES:
Stop the motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
CAUTION
The belt tension arm & needs to be held firmly while
displacing to prevent injury.
CAUTION
Never use the snowblower without the belt guard.
After installing the belt, hook the winch cable (item 1)
to the hook (item 2) and secure with a 2.5mm hair pin
(item 3).
Familiarize yourself with the winch control and make
sure the cable stays wrapped from the bottom of the
drum of the winch. See picture of the winch in the
subframe section.
Lift and lower the snowblower using the switch.
When lowering the accessory, release the switch of
the winch control as soon as the accessory touches
the ground.
17
ASSEMBLY
STEP 6
INSTALLATION OF THE CONTROL BOX:
NOTE: Before choosing the ideal place to install the
control support (item 1) and control box, connect the
control box wires to the motors and to the battery (see
instructions below).
Use the joystick to determine which direction activates
which motor.
We suggest putting the control box on the right fender of
the tractor close to the drivers seat or close to the
steering wheel according to your preference.
Secure the control support with two 1/4 x 3/4" bolts and
flange nuts.
Install the control box on the support.
Determine direction of joystick and position of control
box before installing the support.
Thread the wires on the frame to the front where they
will not be seen and where they wont touch any hot or
moving parts.
Attach to the vehicle’s frame using the tie wraps.
NOTE: It is recommended to place the wire connectors
as close as possible to the subframe. Secure the wires
in an adequate place in order to separate the accessory
from the vehicle when storing.
Connect the wires to the electric motors. The longest
wires are connected to the deflector motor.
Connect the red wire to the positive battery post and
the black wire to the negative battery post.
Connect the wires to the motors and battery.
18
ASSEMBLY
Turn the chute to its maximum towards the right and
lower the deflector.
Secure the wire for the deflector motor (item 1) with a tie
wrap around the motor.
Tie the wire for the deflector with another tie wrap in the
hole (item 3) at the base of the deflector as shown.
Secure the wires for the rotation motor (item 2) with a tie
wrap.
Be sure to leave enough wire length to be able to turn
the chute.
Secure wires on the motors
STEP 7
SNOW DRIFT CUTTERS INSTALLATION:
Refer to parts breakdown included in the box for the
drift cutters for parts identification.
Please follow the instructions included in the box for
the Snow Drift Cutters #700260.
This kit is included with the snowblower.
STEP 8
REAR COUNTERWEIGHT
INSTALLATION:
Refer to parts breakdown included in the box for the
Rear Counterweights for parts identification.
Please follow the instructions included in the box for
the Rear Counterweights #700246-5.
This kit is included with the snowblower.
Install drift cutters
Install counterweights
Adjust skid shoes
VERIFY TIRE PRESSURE:
Tire pressure must be even on both sides of tractor
according to the owner’s manual of the vehicle.
VERIFY SKID SHOE ADJUSTMENT:
LEVEL PAVED SURFACE: Adjust skid shoes to allow
3/16" to 1/4" or 5mm to 7mm clearance (A) between
cutting edge and surface.
UNEVEN OR GRAVEL SURFACE: Adjust skid shoes
to allow 1/2" to 5/8" or 13mm to 16mm clearance (A)
between cutting edge and surface.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Bercomac 610001 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur

dans d''autres langues