Eizo FDF2121WT-A Manuel utilisateur

Important

Please read this “User’s Manual”, and “Setup Manual” (separate

volume) carefully to familiarize yourself with safe and effective usage.

• Refer to the “Setup Manual” for information on the installation /

connection of the monitor.

• For the latest product information including the “User’s Manual”,

refer to our web site :

http://www.eizoglobal.com

Touch Panel Color LCD Monitor

User’s Manual

2

This product has been adjusted specically for use in the region to which it was originally shipped. If

operated outside this region, the product may not perform as stated in the specications.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by

any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.

EIZO Corporation is under no obligation to hold any submitted material or information condential unless

prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every

effort has been made to ensure that this manual provides up-to-date information, please note that EIZO

monitor specications are subject to change without notice.

3

Notice for this monitor

This product is suited to general purposes like creating documents, viewing multimedia content.

This product has been adjusted specically for use in the region to which it was originally shipped. If the

product is used outside the region, it may not operate as specied in the specications.

This product may not be covered by warranty for uses other than those described in this manual.

The specications noted in this manual are only applicable when the following are used:

• Power cords provided with the product

• Signal cables specied by us

Only use optional products manufactured or specied by us with this product.

If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to

the composition of the rubber. Check the desk surface before use.

It takes about 30 minutes (under our measurement conditions) for the monitor display to stabilize. Please

wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor.

Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and

maintain a stable display.

When the screen image is changed after displaying the same image for extended periods of time, an

afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for

extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for

a short period of time. To remove such a phenomenon, change the image or keep the power turned off for

several hours.

If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To

maximize the life of the monitor, we recommend the monitor be turned off periodically.

Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer

to “Cleaning” (page 4)).

The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may

appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.

The backlight of the LCD panel has a xed lifetime. Depending on the usage pattern, such as usage for

long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the

screen becomes dark or begins to icker, please contact your local EIZO representative.

Do not scratch or press on the LCD panel with any sharp objects, at this may result in damage to the LCD

panel. Do not attempt to brush with tissues as this may scratch the panel.

When the monitor is cold and brought into a room or the room temperature goes up quickly, dew

condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the

monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the

monitor.

(Cautions for the Use of the Touch Panel)

• During touch operation

Be careful of the following points. Otherwise, damage to the monitor or malfunctions may occur.

-

Do not strongly press, scratch, or poke the panel.

-

Do not touch the panel with hard objects such as ballpoint pens or metals.

-

Do not touch the black periphery of the screen.

-

Do not stick tape or anything else onto the panel or the black periphery of the panel.

-

If any liquid comes into contact with the panel, wipe it off immediately.

-

Do not allow liquid to enter between the panel and the panel frame.

4

Notice for this monitor

Cleaning

The stains on the cabinet and LCD panel surface can be removed by moistening part of a soft cloth with water.

Attention

• Do not allow liquid to enter the clearance between the panel and the panel frame.

• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet

or LCD panel, and also quality deterioration of the image.

• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.

Note

• It is recommended that ScreenCleaner (available as an option) be used to clean the cabinet and LCD panel surface.

To use the monitor comfortably

• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor

according to the environmental conditions.

• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5

CONTENTS

Notice for this monitor ......................................... 3

Cleaning .................................................................... 4

To use the monitor comfortably ............................. 4

CONTENTS ............................................................. 5

Chapter 1 Introduction ....................................... 6

1-1. Features ......................................................... 6

1-2. EIZO LCD Utility Disk.................................... 6

●

Disk contents and software overview ............. 6

1-3. Basic Operations and Functions ................ 7

●

Basic operation of the Setting menu ............... 7

●

Functions ......................................................... 8

Chapter 2 Adjusting Screens ............................ 9

2-1. Setting the Resolution ................................. 9

●

Windows 10 ..................................................... 9

●

Windows 8.1 / Windows 7 ............................... 9

2-2. Adjusting Color ............................................10

●

To select the display mode

(FineContrast Mode) ......................................10

●

To perform advanced adjustments ................11

●

Adjustable settings in each mode ..................11

●

To adjust brightness .......................................11

●

To adjust contrast ...........................................12

●

To adjust color temperature ...........................12

●

To adjust gamma ...........................................13

●

To adjust the color saturation .........................13

●

To adjust hue ..................................................13

●

To adjust gain .................................................14

2-3. Screen Adjustment ......................................15

●

Digital Signal Input .........................................15

●

Analog Signal Input ........................................15

2-4. Screen Size Changing .................................19

●

Screen Size Changing ...................................19

●

To adjust brightness of non-display area .......19

Chapter 3 Setting Monitor ............................... 20

3-1. Adjusting Volume........................................ 20

3-2. Selecting sound source while using the

DisplayPort signal input............................. 20

3-3. Enabling / Disabling DDC/CI

communication .......................................... 20

3-4. Locking Operation Buttons ........................21

3-5. Showing and hiding the EIZO logo ............21

3-6.

Changing Setting Menu Display Position ...

21

3-7. Setting Language .........................................21

3-8. Resetting the Monitor to the Default

Settings ........................................................ 22

●

To reset the color adjustments ...................... 22

●

To reset all adjustments to the default

settings .......................................................... 22

Chapter 4 Touch Panel Settings .................... 23

4-1. Calibrating the Monitor .............................. 23

4-2. ConguringTouchPanelOperation

Settings ........................................................ 25

Chapter 5 Power Saving Functions ................ 26

5-1. Setting Power Saving ................................. 26

●

Monitor .......................................................... 26

●

Audio Output ................................................. 27

5-2. Setting Power Indicator .............................. 27

5-3. Enabling / Disabling Auto Power-OFF ...... 27

Chapter 6 Troubleshooting .............................. 28

6-1. No picture .................................................... 28

6-2. Imaging problems (for both digital and

analog) .......................................................... 29

6-3. Imaging problems (for analog only) ......... 30

6-4. Touch panel problems .................................31

6-5. Other problems ........................................... 32

Chapter 7 Reference ........................................ 33

7-1. Attaching the Optional Arm ....................... 33

7-2. Connecting Multiple PCs ........................... 35

●

To switch among input signals ...................... 35

●

To set input signal selection .......................... 36

7-3. Displaying Monitor Information ................ 36

7-4. Preset Timing ...............................................37

Chapter 8 Glossary .......................................... 38

Appendix .............................................................. 40

Trademark ............................................................... 40

License / Copyright ................................................ 40

FCC Declaration of Conformity .............................41

LIMITED WARRANTY ............................................. 42

Recycling Information ........................................... 52

China Measures for RoHS Compliance in

ChinaRoHS .............................................................. 56

6

Chapter 1 Introduction

Thank you very much for choosing an EIZO color LCD monitor.

1-1. Features

• 21.5″ wide format LCD

• Supports a resolution of 1920 × 1080

• Touch Panel provided

- Surface Acoustic Wave technology

- Supported OS: Microsoft Windows 10 / Windows 8.1 / Windows 7

- Supports the Windows Touch function (multi-touch) of Microsoft Windows 10 / Windows 8.1 /

Windows 7.

*1

*1 This product supports up to two simultaneous touches (multi-touch support).

• 3 signal input terminals (DVI-D × 1, DisplayPort × 1, D-Sub × 1)

- Applicable to DisplayPort (applicable to 8 bit)

*2

The DisplayPort input receives both an image signal and an audio signal via a single DisplayPort cable.

*2 When transmitting an audio signal using the DisplayPort cable, the graphics board must be compatible

with audio output (see “Specications” in the Setup Manual).

• The FineContrast function allows the user to select the display mode optimum to the displayed

image.

• Flattening of the bezel allows smooth touch operations.

• Small footprint achieved through low-prole and lightweight design

The monitor can be readily moved and its position adjusted.

• Power saving function

Suppressing the power consumption reduces the carbon dioxide emissions. This product is equipped with

power saving function.

- 0 W power consumption when the main power is off

Equipped with main power switch.

When the monitor is not required, the power supply can be shut off using the main power switch.

• Displays HDCP (High-bandwidth Digital Protection) protected contents.

1-2. EIZO LCD Utility Disk

An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk

contents and the overview of the software programs.

●

Disk contents and software overview

The disk includes software programs for adjustment, and User’s Manual. Refer to Readme.txt le on

the disk for software startup procedures or le access procedures.

Item Overview

Screen adjustment pattern les Used when adjusting the image of analog signal input manually.

User’s Manual of this monitor (PDF le)

Readme.txt le

7

Chapter 1 Introduction

1-3. Basic Operations and Functions

●

Basic operation of the Setting menu

1.

Displaying the Setting menu

1. Press . The Setting menu appears.

2.

Adjusting / Setting

1. Choose a menu to adjust / set with , , and then press . The Sub menu appears.

2. Choose an item to adjust / set with , , and then press . The adjustment / setting menu

appears.

3. Adjust / set the selected item with , , and then press .

3.

Exiting

1. Choose “Return” from the Sub menu and press . The Setting menu appears.

2. Choose “Exit” from the Main menu and press

. The Setting menu quits.

Note

• The Setting menu can also be exited by pressing twice quickly.

8

Chapter 1 Introduction

●

Functions

The following table shows the Setting menu and setting items of each menu.

Main menu Setting Reference

Color

*1

Brightness “2-2. Adjusting Color” (page 10)

Contrast

Temperature

Gamma

Advanced Settings Saturation

Hue

Gain

Color Reset “To reset the color adjustments” (page

22)

Screen Screen Size “Screen Size Changing” (page 19)

Smoothing “2-3. Screen Adjustment” (page 15)

Analog Adjustment

*2

Auto Screen Adjust

Auto Range Adjust

Clock

Phase

Hor.Position

Ver.Position

Sound Source “3-2. Selecting sound source while using

the DisplayPort signal input” (page 20)

Power Save “Audio Output” (page 27)

PowerManager Power Save “5-1. Setting Power Saving” (page 26)

Eco Timer “5-3. Enabling / Disabling Auto Power-

OFF” (page 27)

Monitor Settings Input Signal “To set input signal selection” (page

36)

Power Indicator “5-2. Setting Power Indicator” (page

27)

Language “3-7. Setting Language” (page 21)

DDC/CI “3-3. Enabling / Disabling DDC/CI

communication” (page 20)

Border Intensity “To adjust brightness of non-display area”

(page 19)

Menu Settings Logo “3-5. Showing and hiding the EIZO logo”

(page 21)

Menu Position “3-6. Changing Setting Menu Display

Position” (page 21)

Reset “To reset all adjustments to the default

settings” (page 22)

Information “7-3. Displaying Monitor Information”

(page 36)

*1 The adjustment / settings available on the “Color” menu depend on the selected Color mode. (“Adjustable

settings in each mode” (page 11))

*2 These functions can be adjusted with analog input.

9

Chapter 2 Adjusting Screens

2-1. Setting the Resolution

When you connect the monitor to the PC and nd that the resolution is improper, or when you want to

change the resolution, follow the procedure below.

●

Windows 10

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Display Settings”.

3. On the “Customize your display” dialog box, click “Advanced display settings”.

4. Select a monitor, then choose a resolution from the “Resolution” pull-down menu.

5. Click the “Apply” button.

6. When a conrmation dialog box is displayed, click “Keep changes”.

●

Windows 8.1 / Windows 7

1. For Windows 8.1, click the “Desktop” tile on the Start Screen to display the desktop.

2. Right-click the mouse anywhere on the desktop except for icons.

3. From the displayed menu, click “Screen resolution”.

4. On the “Screen Resolution” dialog box, select the monitor.

5. Click “Resolution” to select the desired resolution.

6. Click the “OK” button.

7. When a conrmation dialog box is displayed, click “Keep changes”.

10

Chapter 2 Adjusting Screens

2-2. Adjusting Color

●

To select the display mode (FineContrast Mode)

This function allows easy selection of a desired mode according to monitor application.

Display Modes

Mode Purpose

User1 Select this to dene a desired set of parameter settings.

User2

sRGB Suitable for color matching with sRGB compatible peripherals.

The mode menu

appears.

Procedure

1. Press

.

The mode menu appears at the bottom left of the screen.

2. The mode among the list is highlighted in turn each time is pressed.

You can switch the mode with or while the mode menu is displayed.

→User1←→User2←→sRGB←

Note

• The Setting menu and the Mode menu cannot be displayed at the same time.

11

Chapter 2 Adjusting Screens

●

To perform advanced adjustments

The “Color” menu of the Setting menu allows you to set and save the independent color adjustment

for each mode.

Attention

• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more

after the monitor power has been turned on, and then adjust the monitor.

• Perform the range adjustment rst when adjusting color for analog signals (see “To adjust color gradation

automatically” (page 18)).

• The same image may be seen in different colors on multiple monitors due to their monitor-specic

characteristics. Make ne color adjustment visually when matching colors on multiple monitors.

●

Adjustable settings in each mode

The adjustable settings depend on the mode. (Non-adjustable or non-settable function cannot be

selected.)

√: Adjustable -: Not adjustable

Function

FineContrast Mode

User1 User2 sRGB

Brightness √ √ √

Contrast √ √ -

Temperature √ √ -

Gamma √ √ -

Advanced Settings Saturation √ √ -

Hue √ √ -

Gain √ √ -

Color Reset √ √ √

●

To adjust brightness

The screen brightness is adjusted by changing the brightness of the backlight (light source from the

LCD back panel).

Adjustable range

0 to 100

Procedure

1. Press

.

2. Use

or for adjustment.

3. Press

to exit.

Note

• If you feel that the image is too dark even if the brightness is set to 100, adjust the contrast.

• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.

12

Chapter 2 Adjusting Screens

●

To adjust contrast

The brightness of the screen is adjusted by varying the video signal level.

Adjustable range

0 to 100

Procedure

1. Choose “Color” in the Setting menu, and press

.

2. Choose “Contrast” in the “Color” menu, and press

.

The “Contrast” menu appears.

3. Use or for adjustment.

4. Press

to exit.

Note

• In the contrast of 50, every color gradation is displayed.

• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the

gradation characteristics, prior to the contrast adjustment.

• Perform the contrast adjustment in the following cases.

- When you feel the image is too dark even if the brightness is set to 100 (Set the contrast to higher than 50.)

●

To adjust color temperature

Color temperature can be adjusted.

The color temperature is normally used to express the hue of “White” and / or “Black” by a numerical

value. The value is expressed in degrees “K” (Kelvin).

The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like

the ame temperature. A gain preset value is set for each color temperature setting value.

Adjustable range

Off, 4000 K-10000 K (specied by every 500 K unit, including 9300 K)

Procedure

1. Choose “Color” in the Setting menu, and press

.

2. Choose “Temperature” in the “Color” menu, and press

.

The “Temperature” menu appears.

3. Use or for adjustment.

4. Press

to exit.

Note

• The value shown in “K” is available only as reference.

• “Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 14)).

• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).

• When gain is changed, the color temperature is changed to “Off”.

13

Chapter 2 Adjusting Screens

●

To adjust gamma

Gamma can be adjusted. The brightness of the monitor varies depending on the input signal,

however, the variation rate is not proportional to the input signal. To keep the balance between the

input signal and the brightness of the monitor is called as “Gamma correction”.

Adjustable range

1.8, 2.0, 2.2

Procedure

1. Choose “Color” in the Setting menu, and press

.

2. Choose “Gamma” in the “Color” menu, and press

.

The “Gamma” menu appears.

3. Use or for adjustment.

4. Press

to exit.

●

To adjust the color saturation

This function allows you to adjust color saturation.

Adjustable range

-50 to 50

Procedure

1. Choose “Color” in the Setting menu, and press

.

2. Choose “Advanced Settings” in the “Color” menu, and press

.

3. Choose “Saturation” in the “Advanced Settings” menu, and press

.

The “Saturation” menu appears.

4. Use or for adjustment.

5. Press

to exit.

Attention

• Using this function may make some color gradations unavailable for display.

Note

• The minimum value (-50) changes the screen to monochrome.

●

To adjust hue

This function allows you to adjust hue.

Adjustable range

-50 to 50

Procedure

1. Choose “Color” in the Setting menu, and press

.

2. Choose “Advanced Settings” in the “Color” menu, and press

.

3. Choose “Hue” in the “Advanced Settings” menu, and press

.

The “Hue” menu appears.

4. Use or for adjustment.

5. Press

to exit.

Attention

• Using this function may make some color gradations unavailable for display.

14

Chapter 2 Adjusting Screens

●

To adjust gain

The brightness of each color component red, green, and blue is called “Gain”. You can change the

hue of “white” by adjusting gain.

Adjustable range

0 to 100

Procedure

1. Choose “Color” in the Setting menu, and press

.

2. Choose “Advanced Settings” in the “Color” menu, and press

.

3. Choose “Gain” in the “Advanced Settings” menu, and press

.

The “Gain” menu appears.

4. Adjust gain with or for each of red, green, and blue.

5. Press

to exit.

Attention

• Using this function may make some color gradations unavailable for display.

Note

• The value of gain changes with that of color temperature.

• When gain is changed, the color temperature is changed to “Off”.

15

Chapter 2 Adjusting Screens

2-3. Screen Adjustment

●

Digital Signal Input

When digital signals are input, images are displayed correctly based on the preset data of the

monitor, but if characters and / or lines appear blurred, go to “To modify blurred characters / lines”

(page 18).

When performing more advanced adjustment, see “2-2. Adjusting Color” (page 10) and subsequent

pages.

●

Analog Signal Input

Attention

• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more

after the monitor power has been turned on, and then adjust the monitor.

• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of

800 × 600 (SVGA).

• The self adjustment (or automatic screen adjustment) function works correctly when an image is fully

displayed over the Windows or Macintosh display area. They do not work properly in the cases below:

- When an image is displayed only on a part of the screen (command prompt window, for example)

- When a black background (wallpaper, etc.) is in use

Also, these functions cannot work properly in some graphic boards.

The monitor screen adjustment is used to suppress ickering of the screen or adjust screen position

and screen size correctly according to the PC to be used.

Note

• The Self Adjust function works when all of the following conditions are satised:

- When a signal is input into the monitor for the rst time or when a resolution or vertical / horizontal scan

frequency not used before is set

If the screen is not displayed correctly even after performing the Self Adjust operation, adjust the

screen according to the procedures on the following pages to use the monitor comfortably.

Setting Procedures

1.

Perform the auto adjustment.

●

Toadjustickering,screenposition,andscreensizeautomatically

Procedure

1. Choose “Screen” in the Setting menu, and press

.

2. Choose “Analog Adjustment” in the “Screen” menu, and press

.

3. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press

.

4. Select “Yes” with

or , and press .

Flickering, screen position, and screen size are corrected by the auto-adjustment function.

If the screen is not displayed correctly even after performing the auto adjustment, perform adjustments

according to the following procedure. If the screen is displayed correctly, go to “5. Adjusting color gradation.”

(page 18).

16

Chapter 2 Adjusting Screens

2.

Prepare to use analog screen adjustment patterns.

Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern les”.

Note

• For details and instructions on opening the “Screen adjustment pattern les”, refer to the Readme.txt le.

3.

Perform the auto adjustment again with the analog screen adjustment pattern

displayed.

●

Toadjustickering,screenposition,andscreensizeautomatically

Procedure

1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern les”.

2. Choose “Screen” in the Setting menu, and press .

3. Choose “Analog Adjustment” in the “Screen” menu, and press

.

4. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press

.

5. Select “Yes” with

or , and press .

Flickering, screen position, and screen size are corrected by the auto-adjustment function.

If the screen is not displayed correctly even after performing the auto adjustment, perform adjustments

according to the following procedure. If the screen is displayed correctly, go to “5. Adjusting color gradation.”

(page 18).

4.

Choose “Screen” from the Setting menu to perform advanced adjustments.

Adjust the clock, phase and position, in this order.

●

To eliminate vertical bars

Procedure

1. Choose “Analog Adjustment” in the “Screen” menu, and press

.

2. Choose “Clock” in the “Analog Adjustment” menu, and press

.

The “Clock” menu appears.

3. Adjust the clock with or to eliminate vertical bars.

Press or slowly so as not to miss the adjustment point.

4. Press to exit.

When blurring, ickering or bars appear on the screen after adjustment, proceed to “To remove ickering or

blurring ”.

17

Chapter 2 Adjusting Screens

●

Toremoveickeringorblurring

Procedure

1. Choose “Analog Adjustment” in the “Screen” menu, and press

.

2. Choose “Phase” in the “Analog Adjustment” menu, and press

.

The “Phase” menu appears.

3. Adjust the phase with or to minimize ickering or blurring.

4. Press

to exit.

When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars ”.

(Clock → Phase → Position)

Attention

• Flickering or blurring may not be eliminated depending on your PC or graphics board.

●

To correct the screen position

Note

• Since the number of pixels and the pixel positions are xed on the LCD monitor, only one position is provided

to display images correctly. The position adjustment is made to shift an image to the correct position.

Procedure

1. Choose “Analog Adjustment” in the “Screen” menu, and press

.

2. Choose “Hor.Position” or “Ver.Position” from the “Analog Adjustment” menu, and press

.

The “Hor. Position” or “Ver. Position” menu appears.

3. Adjust the position with or .

4. Press

to exit.

5. Close Pattern 1.

18

Chapter 2 Adjusting Screens

5.

Adjusting color gradation.

●

To adjust color gradation automatically

Every color gradation (0 to 255) can be displayed by adjusting the signal output level.

Procedure

1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern les”.

2. Choose “Screen” in the Setting menu, and press .

3. Choose “Analog Adjustment” in the “Screen” menu, and press

.

4. Choose “Auto Range Adjust” in the “Analog Adjustment” menu, and press

.

5. Select “Yes” with

or , and press .

The output range is set automatically.

6. Close Pattern 2.

6.

Modify blurred characters or lines.

●

To modify blurred characters / lines

When an image is displayed with a resolution other than recommended, the characters or lines of

the displayed image may blur.

Attention

• Smoothing setting may not be required depending on the display resolution. (You cannot choose the

smoothing icon.)

Adjustable range

1 to 5

Procedure

1. Choose “Screen” in the Setting menu, and press

.

2. Choose “Smoothing” in the “Screen” menu, and press

.

The “Smoothing” menu appears.

3. Use or for adjustment.

4. Press

to exit.

19

Chapter 2 Adjusting Screens

2-4. Screen Size Changing

●

Screen Size Changing

The image with the resolution other than the recommended resolution is displayed in full screen

automatically. You can change the screen size by using the “Screen Size” function.

Setting Function

Full Screen Displays an image in full screen. Images are distorted in some cases because the vertical

rate is not equal to the horizontal rate.

Enlarged Displays an image in full screen. In some cases, a blank horizontal or vertical border

appears to equalize the vertical rate and the horizontal rate.

Normal Displays images with the specied resolution.

Example: Image size 1024 × 768

Full Screen Enlarged Normal

(1920 × 1080) (1440 × 1080) (1024 × 768)

Procedure

1. Choose “Screen” in the Setting menu, and press

.

2. Choose “Screen Size” in the “Screen” menu, and press

.

The “Screen Size” menu appears.

3. Select “Full Screen”, “Enlarged”, or “Normal” with or .

4. Press

to exit.

Attention

• Selecting “Normal” may make some color gradations unavailable for display.

●

To adjust brightness of non-display area

A border (black area with no image) around the image appears in the “Normal” or “Enlarged” mode.

Border

Procedure

1. Choose “Monitor Settings” in the Setting menu, and press

.

2. Choose “Border Intensity” in the “Monitor Settings” menu, and press

.

The “Border Intensity” menu appears.

3. Use or for adjustment.

4. Press

to exit.

20

Chapter 3 Setting Monitor

3-1. Adjusting Volume

This function allows you to adjust the speaker volume.

Adjustable range

0 to 30

Procedure

1. Press

.

2. Use

or for adjustment.

3. Press

to exit.

3-2. Selecting sound source while using the DisplayPort

signal input

This function allows you to switch sound source during DisplayPort signal input. You can select the

Stereo Mini Jack or DisplayPort.

Procedure

1. Choose “Sound” in the Setting menu, and press

.

2. Choose “Source” in the “Sound” menu, and press

.

The “Source” menu appears.

3. Select “Stereo Mini Jack” or “DisplayPort” with or .

4. Press

to exit.

Note

• This function is available with DisplayPort signal input.

3-3. Enabling / Disabling DDC/CI communication

This function allows you to enable / disable the DDC/CI communication (see “Chapter 8 Glossary” (page

38)).

Procedure

1. Choose “Monitor Settings” in the Setting menu, and press

.

2. Choose “DDC/CI” in the “Monitor Settings” menu, and press

.

The “DDC/CI” menu appears.

3. Select “On” or “Off” with or .

4. Press

to exit.

Note

• The DisplayPort input of this monitor does not support DDC/CI communication.

La page charge ...

Eizo FDF2121WT-A Manuel utilisateur

Eizo FDF2121WT-A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents