Eizo Computer Monitor CG276 Manuel utilisateur

Important

Please read PRECAUTIONS, this User’s Manual, and the Setup Guide

(separate volume) carefully to familiarize yourself with safe and

effective usage.

• Please refer to the Setup Guide for basic information ranging from

connection of the monitor to a PC to using the monitor.

• The latest User’s Manual is available for download from our web site:

http://www.eizo.com

Cover

2



Location of Caution Statement

This product has been adjusted specically for use in the region to which it was originally shipped. If operated

outside this region, the product may not perform as stated in the specications.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,

electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.

EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information condential

unless prior arrangements are made pursuant to EIZO NANAO CORPORATION’s receipt of said information.

Although every effort has been made to ensure that this manual provides up-to-date information, please note that

EIZO monitor specications are subject to change without notice.

3

Noticeforthismonitor

Notice for this monitor

Aside from general purposes like creating documents, viewing multimedia content, this product is also suited to

applications such as creations of images and graphics, and digital photo processing, where accurate color reproduction

is a priority.

This product has been adjusted specically for use in the region to which it was originally shipped. If the product is

used outside the region, it may not operate as specied in the specications.

This product may not be covered by warranty for uses other than those described in this manual.

The specications noted in this manual are only applicable when the following are used:

· Power cords provided with the product

· Signal cables specied by us

Only use optional products manufactured or specied by us with this product.

It takes about 7 minutes (under our measurement conditions) for the performance of electrical parts to stabilize. Please

wait 7 minutes or more after the monitor power has been turned on, and then adjust the monitor.

Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a

stable display.

When the screen image is changed after displaying the same image for extended periods of time, an afterimage may

appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.

Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to

“Cleaning” (page 4)).

The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on

the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.

The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker, please contact

your local EIZO representative.

Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference

patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure

marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)

Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt

to brush with tissues as this may scratch the panel.

When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may

occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until

the dew condensation disappears, otherwise it may cause some damage to the monitor.

4

Noticeforthismonitor

Cleaning

Attention

• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,

and also quality deterioration of the image.

• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.

If necessary, the stains on the cabinet and panel surface can be removed by using the provided ScreenCleaner.

To use the monitor comfortably

• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to

the environmental conditions.

• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5

CONTENTS

Cover ...................................................................... 1

Notice for this monitor ......................................... 3

Cleaning .................................................................... 4

To use the monitor comfortably ............................. 4

CONTENTS ............................................................. 5

Chapter 1 Introduction ....................................... 7

1-1. Features ......................................................... 7

1-2. Controls and Functions ............................... 9

1-3. EIZO LCD Utility Disk...................................10

●

Diskcontentsandsoftwareoverview............10

●

TouseColorNavigator...................................10

1-4. Basic Operations and Functions ...............11

●

BasicAdjustmentmenuoperations...............11

●

ShowingButtonGuide...................................12

●

Functions........................................................13

Chapter 2 Adjusting Screens .......................... 15

2-1. Compatible Resolutions .............................15

●

DigitalInput(DVI-D,DisplayPort)..................15

●

DigitalInput(HDMI)........................................15

2-2. Setting Resolution .......................................16

●

Windows7......................................................16

●

WindowsVista................................................16

●

WindowsXP...................................................16

●

MacOSX.......................................................16

2-3. Adjusting Color ............................................17

●

Toselectthedisplaymode(colormode).......17

●

Toperformadvancedadjustments................18

●

Adjustablesettingsineachmode..................18

●

AdjustingBrightness......................................19

●

Adjustingthetemperature..............................19

●

AdjustingGamma.......................................... 20

●

AdjustingHue................................................ 20

●

AdjustingSaturation.......................................21

●

Toenhanceoutlineofimage..........................21

●

Tosetclipping............................................... 22

●

AdjustingGain............................................... 23

●

Adjustingthebrightnessandcolorof

black“BlackLevel”........................................ 23

●

Adjusting6Colors..........................................24

2-4. Expanding Signal Output Range .............. 24

2-5. Selecting Screen Size ................................ 25

●

DVI,DisplayPort(PCsignal)input................ 25

●

HDMI(HDsignal)input................................. 26

●

HDMI(SDsignal)input................................. 26

2-6. Conguring Moving Image Performance . 27

2-7. Specifying Color Space ............................. 27

2-8. Setting HDMI ................................................ 28

●

Reducingnoise............................................. 28

●

Selectinghowtodisplayinterlacesignal...... 28

●

SettingSafeArea.......................................... 29

Chapter 3 Setting Monitor ............................... 31

3-1. Enabling/Disabling Mode Selection ..........31

3-2. Selecting the Language ..............................31

3-3. Setting Orientation ......................................31

3-4. Changing Adjustment Menu Display

Position ........................................................ 32

3-5. Showing and Hiding the EIZO Logo ......... 32

3-6. Locking Operation Buttons ....................... 32

3-7. Setting Signal Bandwidth .......................... 33

3-8. Switching USB Port Automatically ........... 33

3-9. Changing DUE (Digital Uniformity

Equalizer) Setting ....................................... 34

3-10. Reset to default ........................................... 34

●

Toresetthecoloradjustments...................... 34

●

Toresetalladjustmentstothedefault

settings.......................................................... 35

Chapter 4 SelfCalibration ................................ 36

4-1. Setting Calibration Details ......................... 36

●

Settingmonitordateandtime....................... 36

●

Settingcalibrationschedule...........................37

●

SetthemodeforwhichSelfCalibration

isexecuted.................................................... 38

●

SettingAdjustmentTarget............................. 39

4-2. Executing SelfCalibration .......................... 39

4-3. Checking Adjustment Results ................... 40

Chapter 5 Power Saving Functions ................ 41

5-1. Setting Power Save ......................................41

5-2. Sets the brightness of the indicator ......... 42

5-3. Setting DisplayPort Power Save ............... 42

Chapter 6 Troubleshooting .............................. 43

6-1. No picture .................................................... 43

6-2. Imaging problems ....................................... 44

6-3. Other problems ........................................... 45

6-4. Built-in calibration sensor and

SelfCalibration problems ........................... 46

Chapter 7 Reference ........................................ 47

7-1. Attaching the Optional Arm ........................47

7-2. Connecting Multiple External Devices ..... 48

●

Toswitchamonginputsignals...................... 49

●

Tosetinputsignalselection“Input

Selection”...................................................... 49

6

CONTENTS

7-3. Making Use of USB (Universal Serial

Bus) ............................................................... 50

●

SystemRequirement..................................... 50

●

Procedure...................................................... 50

7-4. Showing Monitor Information.....................51

●

Displayingsignalinformation“SignalInfo”....51

●

DisplayingMonitorInformation“MonitorInfo”51

7-5. Specications ............................................. 52

Chapter 8 Glossary .......................................... 55

Appendix .............................................................. 58

Trademark ............................................................... 58

License .................................................................... 58

FCC Declaration of Conformity ............................ 59

Hinweise zur Auswahl des richtigen

Schwenkarms für Ihren Monitor ........................... 60

Hinweis zur Ergonomie : ....................................... 60

LIMITED WARRANTY ..............................................61

Recycling Information ............................................70

China Measures for RoHS Compliance in

ChinaRoHS ...............................................................74

7

Chapter1Introduction

Chapter 1 Introduction

1-1. Features

• 27.0″ wide format LCD

• Wide color gamut (Adobe RGB coverage: 97%)

• Applicable to the resolution of 2560 × 1440.

• IPS panel with 178˚ horizontal and vertical viewing angles

• Frame synchronization mode supported (23.75 - 30.5Hz, 47.5 - 61.0Hz)

• 3 signal input terminals (DVI-D × 1, HDMI × 1, DisplayPort × 1)

- DisplayPort (applicable to 8 bit and 10 bit)

*1

- HDMI (applicable to 8 bit, 10 bit, and 12 bit)

*1

*1 Not applicable to audio signals.

• Color mode function

Reproduces a color gamut and gamma compliant with the following standard.

- Broadcasting standards “EBU/REC709/SMPTE-C”

- Digital cinema standard “DCI”

- Adobe

®

RGB

See “To select the display mode (color mode)” (page 17)

• Attaching the “Adjustment Certicate”, which describes the factory measurement results of the grayscale and

uniformity characteristics for each monitor

• Supports portrait and landscape format (rotate 90˚ clockwise)

• This product is equipped with a built-in calibration sensor, and supports SelfCalibration in which the monitor

executes calibration independently.

See “Chapter 4 SelfCalibration” (page 36)

• The provided “ColorNavigator” calibration software enables you to calibrate monitor characteristics and

generate color proles

See “1-3. EIZO LCD Utility Disk” (page 10)

• Supports Color Vision Deciency Simulation Software “UniColor Pro”

This software can be downloaded from our web site (http://www.eizo.com).

• Power saving function

Suppressing the power consumption reduces the carbon dioxide emissions. This product is equipped with power saving

function.

- 0 W when the main power is off

Equipped with main power switch.

Turning off the main power switch completely shuts off power supply to the monitor while the monitor is not used.

• Displays HDCP (High-bandwidth Digital Protection) protected contents.

8

Chapter1Introduction

Attention

Be careful of the following points when using the built-in calibration sensor.

Do not touch the built-in calibration sensor.

Itmayreducethemeasurementaccuracyofthebuilt-incalibrationsensor,orresultininjury

orequipmentdamage.

Attention

• A high temperature or high humidity environment may affect the measurement accuracy of the built-in calibration

sensor. We suggest storing and using the monitor under the following conditions.

- Temperature 30ºC or less

- Humidity 70% or less

Avoid storing or using the sensor where it may be exposed to direct sunlight.

Note

• This monitor supports both portrait and landscape format. You can change the orientation of the Setting menu when

using the monitor screen in vertical display position. (See “3-3. Setting Orientation” (page 31))

• For using the monitor with “Portrait” position, the graphics board supporting portrait display is required. When placing

the monitor in a “Portrait” position, settings of your graphics board need to be changed. Refer to the User’s Manual of

the graphics board for details.

9

Chapter1Introduction

1-2. Controls and Functions

1

16

17

10 11 12

13

14

15

7

8 92 4

5

3

6

Adjustmentmenu

*1

1. Built-in calibration sensor Executescalibrationforanindependentmonitor.SelfCalibrationfunction(page36)

2. Ambient Light Sensor Measuresambientlight.

3.

button Switchesinputsignalsfordisplay(“Toswitchamonginputsignals”(page49)).

4.

button ChangesColorMode(page17).

5.

button Cancelsthesetting/adjustmentandexitstheAdjustmentmenu.

6.

buttons

• Providesthemenuselectionaswellastheadjustmentandsettingofafunction.

• DisplaystheBrightnessmenu(“AdjustingBrightness”(page19)).

7.

button

DisplaystheAdjustmentmenu,determinesanitemonthemenuscreen,andsaves

valuesadjusted(page11).

8.

button Turnsthepoweronoroff.

9. Power Indicator

Indicatesthemonitor’soperationstatus.

Blue: Operating

Flashingblue

(2timesforeach):

Inthefollowingcases,thisnotiesthatdisplayre-correction

isrequired.

• WhenthetimerissetinColorNavigator(CALmode)

Orange: Powersavingmode

OFF: Mainpower/Poweroff

10. Main power switch Turnsthemainpoweronoroff.

11. Power connector Connectsthepowercord.

12. Input signal connectors Left:DVI-Dconnector/Center:HDMIconnector/Right:DisplayPortconnector

13. USB upstream port

ConnectstheUSBcabletousethesoftwarethatneedsUSBconnection,ortouse

USBhubfunction(“7-3.MakingUseofUSB(UniversalSerialBus)”(page50)).

Attention

• By default, USB upstream port 1 is enabled. Connect the cable to USB upstream port 1 rst.

14. USB downstream port ConnectsaperipheralUSBdevice.

15. Stand

*2

Usedtoadjusttheheightandangleofthemonitorscreen.

16. Security lock slot ComplieswithKensington’sMicroSaversecuritysystem.

17. Cable holder Coversthemonitorcables.

*1 See “1-4. Basic Operations and Functions” (page 11) for how to use.

*2 An optional arm (or an optional stand) can be attached by removing the stand section (see “7-1. Attaching the Optional Arm”

(page 47)).

10

Chapter1Introduction

1-3. EIZO LCD Utility Disk

An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents

and the overview of the software programs.

●

Disk contents and software overview

The disk includes application software programs for adjustment, and User’s Manual. Refer to “Readme.txt” or

the “read me” le on the disk for software startup procedures or le access procedures.

Contents Overview Windows Macintosh

A“Readme.txt”or“readme”le √ √

ColorNavigator Anapplicationsoftwareforcalibratingmonitor

characteristicsandgeneratingICCproles(for

Windows)andAppleColorSyncproles(for

Macintosh).

(APCmustbeconnectedtothemonitorwith

thesuppliedUSBcable.)

√ √

User’sManualofthismonitor(PDFle) √ √

●

To use ColorNavigator

Refer to the corresponding User’s Manual on the CD-ROM disk in order to install and use the software.

When using this software, you will need to connect a PC to the monitor with the supplied USB cable. For

details of the USB cable connection, see “7-3. Making Use of USB (Universal Serial Bus)” (page 50).

11

Chapter1Introduction

1-4. Basic Operations and Functions

●

Basic Adjustment menu operations

1.

Displaying Adjustment Menu

1. Press . The Adjustment menu appears.

Currentmode

Menutitle

Setting

Menu

Item

2.

Adjusting/Setting

1. Choose a menu to adjust/set with , and then press .

2. Choose an item to adjust/set with , and then press .

3. Adjust/set the selected item with , and then press .

3.

Exiting the software

1. Press a few times. The Adjustment menu nishes.

12

Chapter1Introduction

●

Showing Button Guide

When you press the front buttons (except the button), the button guide appears next to the button.

ButtonGuide

Controlbutton

Note

• The button guide will continue to appear while the Adjustment menu or Mode menu is showing.

• The button guide is displayed differently depending on the selected menu or status.

• In CAL mode, the brightness cannot be adjusted even though the button guide is displayed above the

and buttons.

13

Chapter1Introduction

●

Functions

The following table shows the menus for adjustment and setting items of each menu.

Main Menu Item Reference

Color

*1

Brightness

“2-3.AdjustingColor”(page17)

Temperature

Gamma

Advanced

Settings

Hue

Saturation

OutlineEnhancer

Clipping

Gain

BlackLevel

6Colors

ColorReset

“3-10.Resettodefault”(page34)

SelfCalibration

Execute

“4-2.ExecutingSelfCalibration”(page39)

Result

“4-3.CheckingAdjustmentResults”(page40)

Settings

ModeSelection

“4-1.SettingCalibrationDetails”(page36)

Target

Schedule

ClockAdjustment

Screen

ScreenSize

“2-5.SelectingScreenSize”(page25)

Overdrive

“2-6.ConguringMovingImage

Performance”(page27)

ColorSpace

“2-7.SpecifyingColorSpace”(page27)

RangeExtension

“2-4.ExpandingSignalOutputRange”(page

24)

HDMISettings

*2

NoiseReduction

“2-8.SettingHDMI”(page28)

FilmDetection

PseudoInterlace

SafeAreaMarker

SafeAreaSize

BorderColor

14

Chapter1Introduction

Power

Manager

PowerSave

“5-1.SettingPowerSave”(page41)

Indicator

“5-2.Setsthebrightnessoftheindicator”

(page42)

MenuSettings

Language

“3-2.SelectingtheLanguage”(page31)

Orientation

“3-3.SettingOrientation”(page31)

MenuPosition

“3-4.ChangingAdjustmentMenuDisplay

Position”(page32)

Tools

InputSelection

“Toswitchamonginputsignals”(page49)

ModePreset

“3-1.Enabling/DisablingModeSelection”

(page31)

USBSelection

DVI “3-8.SwitchingUSBPortAutomatically”

(page33)

DisplayPort

HDMI

SignalInfo

“7-4.ShowingMonitorInformation”(page51)

MonitorInfo

AllReset

“3-10.Resettodefault”(page34)

*1 The adjustment/settings available on the “Color” menu depend on the selected mode. (See “2-3. Adjusting Color”

(page 17))

*2 These functions can be adjusted with HDMI signal input.

15

Chapter2AdjustingScreens

Chapter 2 Adjusting Screens

2-1. Compatible Resolutions

The monitor supports the following resolutions.

●

Digital Input (DVI-D, DisplayPort)

Resolution Applicable Signals

Vertical scan

frequency

Dot clock DVI-D DisplayPort

640×480 VGA 60Hz

242.0MHz

(Max.)

√ √

720×400 VGATEXT 70Hz

√ √

800×600 VESA 60Hz √ √

1024×768 VESA 60Hz √ √

1280×960 VESA 60Hz √ √

1280×1024 VESA 60Hz √ √

1600×1200 VESA 60Hz √ √

1920×1080 VESACVTRB 60Hz √ √

1920×1200 VESACVTRB 60Hz √ √

2560×1440 SingleLink 30Hz √ -

2560×1440

*1

VESACVTRB 60Hz √ √

●

Digital Input (HDMI)

• Video signal

- VGA / 480i,480p,1080i,720p,1080p: 60 Hz

- 576i,576p,1080i,720p,1080p: 50 Hz

- 1080p: 24 Hz, 25 Hz, 30 Hz

AgraphicsboardinconformancewiththeVESAandCEA-861standardsisrequired.

*1 Recommended resolution

16

Chapter2AdjustingScreens

2-2. Setting Resolution

When you connect the monitor to the PC and nd that the resolution is improper, or when you want to change the

resolution, follow the procedure below.

●

Windows 7

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Screen resolution”.

3. On the “Screen Resolution” dialog box, select the monitor.

4. Click “Resolution” to select the desired resolution.

5. Click the “OK” button.

6. When a conrmation dialog box is displayed, click “Keep changes”.

●

Windows Vista

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Personalize”.

3. On the “Personalization” window, click “Display Settings”.

4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the

“Resolution” eld.

5. Click the “OK” button.

6. When a conrmation dialog box is displayed, click “Yes”.

●

Windows XP

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Properties”.

3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution

for “Screen resolution” under “Display”.

4. Click the “OK” button to close the dialog box.

●

Mac OS X

1. Select “System Preferences” from the Apple menu.

2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.

3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” eld.

4. Your selection will be reected immediately. When you are satised with the selected resolution, close the

window.

17

Chapter2AdjustingScreens

2-3. Adjusting Color

●

To select the display mode (color mode)

This function allows easy selection of a desired mode according to monitor application.

Display Modes

Mode Purpose

1-Custom Availableforthecolorsettingsaccordingtoyourpreference.

2-Adobe

®

RGB SuitableforcolormatchingwithAdobe

®

RGBcompatibleperipherals.

3-sRGB SuitableforcolormatchingwithsRGBcompatibleperipherals.

4-EBU SuitableforreproducingthecolorgamutandgammaassetforthbyEBU(European

BroadcastingUnion)standards.

5-REC709 SuitableforreproducingthecolorgamutandgammaassetforthbytheITU-RRec.709

standard.

6-SMPTE-C SuitableforreproducingthecolorgamutandgammaassetforthbySMPTE-Cstandards.

7-DCI SuitableforreproducingthecolorgamutandgammaassetforthbyDCIstandards.

8-CAL Displaysthescreenadjustedbythe“ColorNavigator”calibrationsoftwareand

SelfCalibration.

Note

• In CAL mode, ColorNavigator and SelfCalibration can be used for adjustment. (See “Chapter 4 SelfCalibration” (page 36))

• Available CAL mode differs depending on each input signal.

Attention

• Avoid operating any function of the monitor while using ColorNavigator.

Example:AtDVIinput

Themodemenu

appears.

1-Custom←→2-Adobe

®

RGB←→3-sRGB←→4-EBU

8-CAL←→7-DCI←→6-SMPTE-C←→5-REC709

Procedure

1. Press

.

The mode menu appears at the bottom left of the screen.

2. The mode among the list is highlighted in turn each time is pressed.

You can switch the mode with or while the mode menu is displayed.

Note

• The Adjustment menu and the Mode menu cannot be displayed at the same time.

• You can disable a specic mode to be selected. For more information, see “3-1. Enabling/Disabling Mode Selection”

(page 31).

18

Chapter2AdjustingScreens

●

To perform advanced adjustments

“Color” of the Adjustment menu allows you to congure and save a separate set of color settings for each

mode.

Attention

• It takes about 7 minutes (under our measurement conditions) for the performance of electrical parts to stabilize. Please

wait 7 minutes or more after the monitor power has been turned on, and then adjust the monitor.

• The same image may be seen in different colors on multiple monitors due to their monitor-specic characteristics. Make

ne color adjustment visually when matching colors on multiple monitors.

• Using ColorNavigator enables the monitor adjustment that prioritizes color matching of multiple monitors. For details,

refer to the ColorNavigator User’s Manual (on the CD-ROM).

Note

• The values shown in “%” or “K” are available only as reference.

●

Adjustable settings in each mode

The adjustable settings depend on the mode. (You cannot select any non-adjustable or non-settable function.)

The adjustments or settings made for each mode are applied to all input signals.

√: Adjustable -: Not adjustable

Function

Color Mode

1-Custom

2-Adobe

®

RGB

3-sRGB 4-EBU

5-REC709

6-SMPTE-C 7-DCI 8-CAL

Brightness √ √ √ √ √ √ √ -

Temperature √ √ √ √ √ √ √ -

Gamma √ √ √ √ √ √ √ -

Hue √ - - - - - - -

Saturation √ - - - - - - -

OutlineEnhancer √ √ √ √ √ √ √ -

Clipping - √ √ √ √ √ √ -

Gain √ - - - - - - -

BlackLevel √ √ √ √ √ √ √ -

6Colors √ - - - - - - -

ColorReset √ √ √ √ √ √ √ -

19

Chapter2AdjustingScreens

●

Adjusting Brightness

The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back

panel).

Setting Range

75cd/m

2

to 350 cd/m

2

Procedure

1. Press

or .

The Brightness menu appears.

2. Use or for adjustment.

3. Press

to exit.

Attention

• If the entered value cannot be set, the value will appear in magenta. In such a case, change the value.

Note

• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.

• The values shown in “cd/m

2

” are available only as reference.

●

Adjusting the temperature

The color temperature can be adjusted.

The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical value.

The value is expressed in degrees “K” (Kelvin).

The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the ame

temperature. The gain preset values are set for each color temperature setting value.

Setting Range

Native, 4000K-10000K (specied every 100K), Standard

Procedure

1. Choose “Color” from the Adjustment menu, and press

.

2. Choose “Temperature” from “Color”, and press

.

3. Use

or for adjustment.

4. Press

to exit.

Note

• “Gain” allows you to perform more advanced adjustment (see “Adjusting Gain” (page 23)).

• If you set “Native”, the image is displayed in the preset color of the monitor (Gain: 100% for each RGB).

• When gain is changed, the color temperature is changed to “User”.

• The default setting for each Adobe

®

RGB/sRGB/EBU/REC709/SMPTE-C/DCI mode is set to “Standard”, which is the

temperature in conformity with each standard.

20

Chapter2AdjustingScreens

●

Adjusting Gamma

Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the

variation rate is not proportional to the input signal. To keep the balance between the input signal and the

brightness of the monitor is called as “Gamma correction”.

Setting Range

1.6 - 2.7, Standard

Procedure

1. Choose “Color” from the Adjustment menu, and press

.

2. Choose “Gamma” from “Color”, and press

.

3. Use

or for adjustment.

4. Press

to exit.

Note

• The default setting for each Adobe

®

RGB/sRGB/EBU/REC709/SMPTE-C/DCI mode is set to “Standard”, which is the

gamma in conformity with each standard.

• The gamma curve can be adjusted to L* by using ColorNavigator. For details, refer to the ColorNavigator User’s Manual

(on the CD-ROM).

●

Adjusting Hue

This function allows you to adjust the hue.

Setting Range

-100 to 100

Procedure

1. Choose “Color” from the Adjustment menu, and press

.

2. Choose “Advanced Settings” from “Color”, and press

.

3. Choose “Hue”, and press

.

4. Use

or for adjustment.

5. Press

to exit.

Attention

• Using this function may make some color gradations unavailable for display.

La page charge ...

Eizo Computer Monitor CG276 Manuel utilisateur

Ce manuel convient également à

Eizo Computer Monitor CG276 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents