Eizo MX220W Le manuel du propriétaire

Catégorie
Téléviseurs
Taper
Le manuel du propriétaire

Ce manuel convient également à

Important
Please read this User’s Manual and Setup Manual (separate volume)
carefully to familiarize yourself with safe and effective usage.
Please refer to the Setup Manual for basic information ranging from
connection of the monitor to a PC to using the monitor.
The latest Users Manual is available for download from our web site:
http://www.eizo.com
Cover
Instructions for Use
Users Manual
2
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please read them carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious injury and can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product
damage.
Indicates a prohibited action.
Indicates to ground for safety.
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
It shall be assured that the nal system is in compliance to IEC60601-1-1 requirement.
Power supplied equipment can emit electromagnetic waves, that could inuence, limit or result in
malfunction of the monitor.
Install the equipment in a controlled environment, where such effects are avoided.
This is a monitor intended for use in a medical image system. It does not support the display of
mammography images for diagnosis.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.
Apple, Mac, Macintosh, iMac, eMac, Mac OS, MacBook, PowerBook, ColorSync, QuickTime, and iBook are registered trademarks of
Apple Inc.
Windows, Windows Vista, Windows Media, SQL Server, and Xbox 360 are registered trademarks of Microsoft Corporation in the
United States and other countries.
A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.
VESA is a registered trademark or a trademark of the Video Electronics Standards Association in the United States and other
countries.
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiForce, RadiCS, RadiNET, Raptor, and ScreenManager are
registered trademarks of EIZO Corporation in Japan and other countries.
All other company and product names are trademarks or registered trademarks of their respective owners.
3
PRECAUTIONS
PRECAUTIONS
IMPORTANT!
• Thisproducthasbeenadjustedspecicallyforuseintheregiontowhichitwasoriginallyshipped.
Ifoperatedoutsidetheregiontowhichitwasoriginallyshipped,theproductmaynotperformasstated
inthespecications.
• Toensurepersonalsafetyandpropermaintenance,pleasereadthissectionandthecautionstatements
ontheunit(refertothegurebelow).
Location of the Caution Statements
Ex. MX241W
Symbols on the unit
Symbol This symbol indicates
Main Power Switch
Press to turn the monitors main power off
Main Power Switch
Press to turn the monitors main power on.
Power Button
Press to turn the monitors power on or off.
Alternating current
Alerting electrical hazard
Caution
Refer to SAFETY SYMBOLS section in this manual.
4PRECAUTIONS
WARNING
If the unit begins to emit smoke, smells like something is burning, or makes
strange noises, disconnect all power connections immediately and contact
your dealer for advice.
Attemptingtouseamalfunctioningunitmayresultinre,electricshock,orequipment
damage.
Do not open the cabinet or modify the unit.
Openingthecabinetormodifyingtheunitmayresultinre,electricshock,orburn.
Refer all servicing to qualied service personnel.
Donotattempttoservicethisproductyourselfasopeningorremovingcoversmayresultin
re,electricshock,orequipmentdamage.
Keep small objects or liquids away from the unit.
Smallobjectsaccidentallyfallingthroughtheventilationslotsintothecabinetorspillage
intothecabinetmayresultinre,electricshock,orequipmentdamage.Ifanobjectorliquid
falls/spillsintothecabinet,unplugtheunitimmediately.Havetheunitcheckedbyaqualied
serviceengineerbeforeusingitagain.
Place the unit at the strong and stable place.
Aunitplacedonaninadequatesurfacemayfallandresultininjuryorequipmentdamage.
Iftheunitfalls,disconnectthepowerimmediatelyandaskyourdealerforadvice.
Donotcontinueusingadamagedunit.Usingadamagedunitmayresultinreorelectric
shock.
Use the unit in an appropriate location.
Notdoingsomayresultinre,electricshock,orequipmentdamage.
Donotplaceoutdoors.
Donotplaceinthetransportationsystem(ship,aircraft,trains,automobiles,etc.)
Donotplaceinadustyorhumidenvironment.
Donotplaceinalocationwherewaterissplashedonthescreen(bathroom,kitchen,etc.).
Donotplaceinalocationwherethesteamcomesdirectlyonthescreen.
Donotplacenearheatgeneratingdevicesorahumidier.
Donotplaceinalocationwheretheproductissubjecttodirectsunlight.
Donotplaceinaninammablegasenvironment.
To avoid danger of suffocation, keep the plastic packing bags away from
babies and children.
Use the enclosed power cord and connect to the standard power outlet of your
country.
Besuretoremainwithintheratedvoltageofthepowercord.Notdoingsomayresultinre
orelectricshock.Powersupply:100-120/200-240Vac,50/60Hz
To disconnect the power cord, grasp the plug rmly and pull.
Tuggingonthecordmaydamageandresultinreorelectricshock. OK
5
PRECAUTIONS
WARNING
The equipment must be connected to a grounded main outlet.
Notdoingsomaycauseinreorelectricshock.
Use the correct voltage.
Theunitisdesignedforusewithaspecicvoltageonly.Connectiontoanothervoltage
thanspeciedinthisUser’sManualmaycausere,electricshock,orequipmentdamage.
Powersupply:100-120/200-240Vac,50/60Hz
Donotoverloadyourpowercircuit,asthismayresultinreorelectricshock.
Handle the power cord with care.
Donotplacethecordunderneaththeunitorotherheavyobjects.
Donotpullonortiethecord.Ifthepowercordbecomesdamaged,stopusingit.Useofa
damagedcordmayresultinreorelectricshock.
For the electrical safety, do not connect or disconnect the power cord in the
presence of patients.
Never touch the plug and power cord if it begins to thunder.
Touchingthemmayresultinelectricshock.
When attaching an arm stand, please refer to the users manual of the arm
stand and install the unit securely.
Notdoingsomaycausetheunittobecomeunattached,whichmayresultininjuryor
equipmentdamage.Beforeinstallation,makesurethatdesks,walls,andothersanarmstand
isxedonhaveadequatemechanicalstrength.
Whentheunitisdropped,pleaseaskyourdealerforadvice.
Donotcontinueusingadamagedunit.Usingadamagedunitmayresultinreorelectric
shock.Whenreattachingthetiltstand,pleaseusethesamescrewsandtightenthemsecurely.
Do not touch a damaged LCD panel directly with bare hands.
Theliquidcrystalwhichleaksfromthepanelispoisonousifitenterstheeyesormouth.
Ifanypartoftheskinorbodycomesindirectcontactwiththepanel,pleasewashthoroughly.
Ifsomephysicalsymptomsresult,pleaseconsultyourdoctor.
Fluorescent backlight lamps contain mercury (the products that have LED
backlight lamps contain no mercury), dispose according to local, state or
federal laws.
Exposuretoelementalmercurycanresultineffectsonthenervoussystem,includingtremor,
memoryloss,andheadache.
6PRECAUTIONS
CAUTION
Handle with care when carrying the unit.
Disconnectthepowercordandcableswhenmovingtheunit.Movingtheunitwiththecord
attachedisdangerous.Itmayresultininjury.
When handling the unit, grip the bottom of the unit rmly with both hands
ensuring the panel faces outward before lifting.
Droppingtheunitmayresultininjuryorequipmentdamage.
Do not block the ventilation slots on the cabinet.
Donotplaceanyobjectsontheventilationslots.
Donotinstalltheunitinaclosedspace.
Donotusetheunitlaiddownorupsidedown.
Blockingtheventilationslotspreventsproperairowandmayresultinre,electricshock,
orequipmentdamage.
Do not touch the plug with wet hands.
Doingsomayresultinelectricalshock.
Use an easily accessible power outlet.
Thiswillensurethatyoucandisconnectthepowerquicklyincaseofaproblem.
Periodically clean the area around the plug.
Dust,water,oroilontheplugmayresultinre.
Unplug the unit before cleaning it.
Cleaningtheunitwhileitispluggedintoapoweroutletmayresultinelectricshock.
If you plan to leave the unit unused for an extended period, disconnect the
power cord from the wall socket after turning off the power switch for the
safety and the power conservation.
This product is only suitable for a patient environment, but not for contact
with a patient.
7
PRECAUTIONS
Notice for this monitor
This product is intended to be used in displaying and viewing digital images for diagnosis of X-ray or MRI, etc. by
trained medical practitioners. It does not support the display of mammography images for diagnosis.
This product has been adjusted specically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. (Refer to
Cleaning” on the next page.)
The screen may have defective pixels or a small number of light dots on the screen. This is due to the characteristics of
the panel itself, and is not a malfunction of the product.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker, please contact
your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference
patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure
marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.
8PRECAUTIONS
Cleaning
Attention
• Chemicalssuchasalcoholandantisepticsolutionmaycauseglossvariation,tarnishing,andfadingofthecabinetorpanel,
andalsoqualitydeteriorationoftheimage.
• Neveruseanythinner,benzene,wax,andabrasivecleaner,whichmaydamagethecabinetorpanel.
Note
• TheoptionalScreenCleanerisrecommendedforcleaningthecabinetandpanelsurface.
Ifnecessary,thestainsonthecabinetandpanelsurfacecanberemovedbymoisteningpartofasoftclothwith
water.
To use the monitor comfortably
• Anexcessivelydarkorbrightscreenmayaffectyoureyes.Adjustthebrightnessofthemonitor
accordingtotheenvironmentalconditions.
• Staringatthemonitorforalongtimetiresyoureyes.Takea10-minuteresteveryhour.
9
CONTENTS
CONTENTS
Cover ............................................................. 1
PRECAUTIONS ..................................................... 3
Notice for this monitor ............................................. 7
CONTENTS ............................................................. 9
Chapter 1 Introduction ..................................... 10
1-1. Features ...........................................................10
1-2. Controls and Functions .................................11
1-3. Utility Disk .......................................................11
Disk contents and software overview ...............11
To RadiCS LE or ScreenManager Pro for Medical .11
1- 4. Basic Operation and Functions ....................12
Basic operation of Adjustment menu................12
Functions ..............................................................13
Chapter 2 Adjusting Screen ............................. 14
2-1. Setting Screen Resolution ...............................14
Compatible Resolutions/Frequencies ...............14
Setting Resolution ...............................................14
Windows 8 / Windows 7 ....................................14
Windows Vista ..................................................14
Windows XP ......................................................14
Mac OS X ..........................................................14
2-2. Displaying Screen Correctly .........................15
Digital Input ..........................................................15
Analog Input .........................................................15
2-3. Color Adjustment ...........................................19
To select the display mode (CAL Switch) .........19
To perform advanced adjustments ...................19
Adjustment items in each mode ....................... 20
To adjust the brightness [Brightness] ...............21
To adjust the contrast [Contrast] .......................21
To adjust the color temperature [Temperature] 21
To adjust the gamma value [Gamma] .............. 22
To adjust the hue [Hue] .................................... 22
To adjust the color saturation [Saturation] ....... 22
To enhance the outline of the image [Outline
Enhancer] ......................................................... 23
To adjust the gain value [Gain] ......................... 23
To adjust six colors [6 Colors] .......................... 23
2-4. Displaying Lower Resolutions..................... 24
To change screen size [Screen Size]................24
Chapter 3 Setting Monitor ................................ 25
3-1. Enabling/Disabling Mode Selection
[Mode Preset] ................................................ 25
3-2. Locking Buttons [Key Lock] ........................ 25
3-3. Setting the EIZO Logo Display [Logo] ........ 26
3-4. Setting Orientation [Orientation] ................ 26
To set the orientation of the Adjustment menu 26
3-5. Setting Language [Language] ..................... 27
3-6. Setting the Display Position of the
Adjustment Menu [Menu Position] .............. 27
3-7. Restoring the Default Setting ...................... 27
To reset color adjustment values [Color Reset] 27
To reset all adjustments to the factory default
settings [All Reset] ........................................... 27
Chapter 4 Power Saving Function ................... 28
4-1. Setting the Power Saving [Power Save] ..... 28
4-2. Setting Power Indicator [Power Indicator] . 28
4-3. Setting Monitor’s Automatic Brightness
Adjustment [Auto EcoView] ......................... 29
Chapter 5 Troubleshooting .............................. 30
Chapter 6 Reference ......................................... 33
6-1. Attaching an Arm .......................................... 33
6-2. Connecting More than Two PCs to the
Monitor ........................................................... 34
To switch the input signal ................................. 34
To set input signal selection [Input Selection] .. 35
6-3. Making Use of USB (Universal Serial Bus) . 36
Required System Environment ........................ 36
Connection Procedure (Setup of USB Function) 36
6-4. Displaying Monitor Information ...................37
Displaying monitor information by pressing .37
Displaying signal information [Signal Info] ........37
Displaying monitor information [Monitor Info] ...37
6-5. Specications ................................................ 38
6-6. Glossary ......................................................... 46
6-7. Preset Timing ................................................. 48
FCC Declaration of Conformity ......................... 49
EMC Information ................................................. 50
LIMITED WARRANTY .......................................... 53
10 Chapter 1 Introduction
Chapter 1 Introduction
ThankyouverymuchforchoosinganEIZOColorMonitor.
1-1. Features
• 24”wideformatLCD(MX241W)
• 22”wideformatLCD(MX220W)
• Applicabletotheresolution1920dotsx1200lines
• ApplicabletoDisplayPort(applicableto8bitor10bit,notapplicabletoaudiosignals)
• 3signalinputterminals(DVI-Ix2,DisplayPortx1)
• CALSwitchfunctionforselectinganoptimalcalibrationmode
“2-3.Toselectthedisplaymode(CALSwitch)”(page19)
• DICOMmode(CALSwitchfunction)(page46)
• Thequalitycontrolsoftware“RadiCSLE”(forWindows)usedtocalibratethemonitorisincluded
1-3.UtilityDisk”(page11)
• Thesoftware“ScreenManagerProforMedical”(forWindows)toadjustthescreenusingthemouse
andkeyboardisincluded
1-3.UtilityDisk”(page11)
• FrameSynchronousmodesupported(59-61Hz)
• Powersavingfunction
Thisproductisequippedwithpowersavingfunction.
-PowerConsumptionwhenmainpowerswitchisOff:0W
Equippedwithmainpowerswitch.
Turningoffthemainpowerswitchcompletelyshutsoffpowersupplytothemonitorwhilethemonitorisnot
used.
-AutoEcoViewfunction
Thesensoronthefrontsideofthemonitordetectstheenvironmentalbrightnesstoadjustthescreenbrightness
automaticallyandcomfortably.
Excessivelyhighbrightnessmayleadadamagetothenaturalenvironmentaswellastoyoureyes.Suppressing
theexcessivelyhighbrightnesswillbehelpfultoreducethepowerconsumptionandthedamagetoyoureyes.
4-3.SettingMonitor’sAutomaticBrightnessAdjustment[AutoEcoView]”(page29)
• HDCP(High-bandwidthDigitalContentProtection)
• Portrait/Landscapedisplayavailable(rotate90degreesclockwise)
NOTE
• ThismonitorsupportsthePortrait/Landscapedisplay.Thisfunctionallowsyoutochangetheorientationofthe
Adjustmentmenuwhenusingthemonitorscreeninverticaldisplayposition.(Referto“Tosettheorientationof
theAdjustmentmenu[Orientation]”onpage26.)
• Forusingthemonitorwith“Portrait”position,thegraphicsboardsupportingportraitdisplayisrequired.When
usingthemonitorwith“Portrait”position,thesettingneedstobechangeddependingonthegraphicsboardused
inyourPC.Refertothemanualofthegraphicsboardfordetails.
11
Chapter 1 Introduction
1-2. Controls and Functions
Ex. MX241W
124567810
39
Operation buttons
Adjustment menu
1. Sensor(AutoEcoView) 6. button
2. button 7. button
3. button 8. button
4. button 9. button
5. button 10. PowerIndicator
Indicator status Operation status
Blue The screen is displayed
Orange Power saving
Off Main Power Switch / Power button off
1-3. Utility Disk
An“EIZOLCDUtilityDisk”(CD-ROM)issuppliedwiththemonitor.Thefollowingtableshowsthe
diskcontentsandtheoverviewofthesoftwareprograms.
Disk contents and software overview
Thediskincludesapplicationsoftwareprogramsforadjustment,andUser’sManual.Referto“Readme.
txt”leonthediskforsoftwarestartupproceduresorleaccessprocedures.
Item Overview
A “Readme.txt” le
RadiCS LE (for Windows) RadiCS LE is quality control software used to calibrate the
monitor and manage the calibration history. (A PC must be
connected to the monitor with the supplied USB cable.) Refer
to the description later.
ScreenManager Pro for Medical
(for Windows)
A utility software program to control monitor adjustments from
a PC using its mouse and keyboard. (A PC must be connected
to the monitor with the supplied USB cable.) Refer to the
description later.
User’s Manual (PDF le)
To RadiCS LE or ScreenManager Pro for Medical
RefertothecorrespondingUser’sManualontheCD-ROMdiskinordertoinstallandusethesoftware.
Whenusingthissoftware,youwillneedtoconnectaPCtothemonitorwiththesuppliedUSBcable.For
moreinformationrefertothe“6-3.MakingUseofUSB(UniversalSerialBus)”(page36).
12 Chapter 1 Introduction
1- 4. Basic Operation and Functions
Basic operation of Adjustment menu
1 Displaying Adjustment Menu
Press .
Theadjustmentmenuappears.
Current mode
Menu title
Settings
Menu
Item
2 Adjusting/Setting
1. Chooseamenutoadjust/setwith ,andpress .
2. Chooseanitemtoadjust/setwith ,andpress .
3. Adjust/settheselecteditemwith ,andpress .
3 Exiting
Press afewtimes.
Theadjustmentmenunishes.
13
Chapter 1 Introduction
Functions
ThefollowingtableshowsalltheAdjustmentmenu’sadjustmentandsettingmenus.
Main Menu Item Adjusting/Setting
Color Brightness 2-3. Color Adjustment” (page 19)
Contrast
Temperature
Gamma
Advanced
Settings
Hue
Saturation
Outline Enhancer
Gain
6 Colors
Color Reset 3-7. Restoring the Default Setting
(page 27)
Screen Screen Size 2-4. Displaying Lower Resolutions”
(page 24)
Analog
Adjustment
Auto Adjustment “2-2. Displaying Screen Correctly
(page 15)
Range Adjustment
Clock
Phase
Hor.Position
Ver.Position
PowerManager Power Save 4-1. Setting the Power Saving” (page 28)
Auto EcoView 4-3. Setting Monitor’s Automatic Brightness
Adjustment” (page 29)
Power Indicator 4-2. Setting Power Indicator” (page 28)
Menu Settings Language 3-5. Setting Language” (page 27)
Orientation 3-4. Setting Orientation” (page 26)
Menu Position 3-6. Setting the Display Position of the
Adjustment Menu” (page 27)
Tools Input Selection “6-2. Connecting More than Two PCs to the
Monitor” (page 34)
Mode Preset 3-1. Enabling/Disabling Mode Selection”
(page 25)
Signal Info “6-4. Displaying Monitor Information”
(page 37)
Monitor Info
All Reset 3-7. Restoring the Default Setting
(page 27)
* Theadjusting/settingfunctiononthe<Color>menudependontheselectedColormode(page20).Theabovetable
showsthesubmenuswhenthe“Custom”modeisselected(See“2-3.ColorAdjustment”(page19)).
14 Chapter 2 Adjusting Screen
Chapter 2 Adjusting Screen
2-1. Setting Screen Resolution
Compatible Resolutions/Frequencies
Fordetailsoncompatibleresolutions,referto“CompatibleResolutions/Frequencies”intheSetup
Manual.
Setting Resolution
WhenyouconnectthemonitortothePCandndthattheresolutionisimproper,orwhenyouwantto
changetheresolution,followtheprocedurebelow.
Windows 8 / Windows 7
1. ForWindows8,clickthe“Desktop”tileontheStartScreentodisplaythedesktop.
2. Right-clickthemouseanywhereonthedesktopexceptforicons.
3. Fromthedisplayedmenu,click“Screenresolution”.
4. Onthe“ScreenResolution”dialog,selectthemonitor.
5. Click“Resolution”toselectthedesiredresolution.
6. Clickthe[OK]button.
7. Whenaconrmationdialogisdisplayed,click[Keepchanges].
Windows Vista
1. Right-clickthemouseanywhereonthedesktopexceptforicons.
2. Fromthedisplayedmenu,click“Personalize”.
3. Onthe“Personalization”window,click“DisplaySettings”.
4. Onthe“DisplaySettings”dialog,selectthe“Monitor”tabandselectdesiredresolutioninthe
“Resolution”eld.
5. Clickthe[OK]button.
6. Whenaconrmationdialogisdisplayed,click[Yes].
Windows XP
1. Right-clickthemouseanywhereonthedesktopexceptforicons.
2. Fromthedisplayedmenu,click“Properties”.
3. Whenthe“DisplayProperties”dialogisdisplayed,clickthe“Settings”tabandselectdesired
resolutionfor“Screenresolution”under“Display”.
4. Clickthe[OK]buttontoclosethedialog.
Mac OS X
1. Select“SystemPreferences”fromtheApplemenu.
2. Whenthe“SystemPreferences”dialogisdisplayed,click“Displays”for“Hardware”.
3. Onthedisplayeddialog,selectthe“Display”tabandselectdesiredresolutioninthe“Resolutions”
eld.
4. Yourselectionwillbereectedimmediately.Whenyouaresatisedwiththeselectedresolution,close
thewindow.
15
Chapter 2 Adjusting Screen
2-2. Displaying Screen Correctly
Digital Input
Whendigitalsignalsareinput,imagesaredisplayedcorrectlybasedonthepresetdataofthemonitor.
Whenperformingadvancedadjustment,see“2-3ColorAdjustment”(page19)andsubsequentpages.
Analog Input
Attention
• Wait30minutesormorefrommonitorpoweronbeforestartingadjustments.
(Allowthemonitortowarmupforatleast30minutesbeforemakingadjustments.)
Themonitorscreenadjustmentisusedtosuppressickeringofthescreenoradjustscreenpositionand
screensizecorrectlyaccordingtothePCtobeused.
TheSelfAdjustfunctionworkswhenallofthefollowingconditionsaresatised.
•WhenasignalisinputintothemonitorforthersttimeorwhentheresolutionorVertical/
HorizontalFrequencynotdisplayedbeforeisset
•Whensignalswiththeverticalresolutionover480areinput
IfthescreenisnotdisplayedcorrectlyevenafterperformingtheSelfAdjustoperation,adjustthescreen
accordingtotheproceduresonthefollowingpagestousethemonitorcomfortably.
[Adjustment Procedure]
1 Perform the auto adjustment.
To adjust ickering, screen position, and screen size automatically [Auto Adjustment]
Procedure
1. Choose<Screen>fromtheAdjustmentmenu,andpress .
2. Choose<AnalogAdjustment>fromthe<Screen>menu,andpress .
3. Choose<AutoAdjustment>,andpress .
Theautoadjustmentfunctionworks(themessage“InProgress”appears)tocorrectlyadjusttheickering,screen
position,andscreensizecorrectly.
Whentheautoadjustmentiscompleted,amessageappears.Select“OK”toconrmthenewsettingsor“Cancel”
torestoretheprevioussettings,andpress .
Attention
• ThisfunctionworkscorrectlywhenanimageisfullydisplayedovertheWindowsorMacintoshdisplayarea.It
doesnotworkproperlywhenanimageisdisplayedonlyonapartofthescreen(commandpromptwindow,for
example)orwhenablackbackground(wallpaper,etc.)isinuse.
• Thisfunctiondoesnotworkcorrectlywithsomegraphicsboards.
Ifthescreenisnotdisplayedcorrectlyevenafteradjustinginstep1above,performtheadjustments
accordingtotheproceduresonthefollowingpages.Whenthescreenisdisplayedcorrectly,gotostep
5“Toadjustcolorgradationautomatically[RangeAdjustment]”.
16 Chapter 2 Adjusting Screen
2 Prepare the display pattern for the analog display adjustment.
Downloadthe“Screenadjustmentpatternles”fromoursite:http://www.eizo.com
NOTE
• Fordetailsandinstructionsonopeningthe“Screenadjustmentpatternles”,refertothe“Readme.txt”le.
3 Perform the auto adjustment again with the analog screen adjustment pattern
displayed.
To adjust ickering, screen position, and screen size automatically [Auto Adjustment]
Procedure
1. DisplayPattern1ofthescreenadjustmentpatternlesinfullscreenonthemonitor.
2. Choose<Screen>fromtheAdjustmentmenu,andpress .
3. Choose<AnalogAdjustment>fromthe<Screen>menu,andpress .
Toproceedwiththesubsequentadjustments,selectanitemin<AnalogAdjustment>ofthe<Screen>menu.
4. Choose<AutoAdjustment>,andpress .
Theautoadjustmentfunctionworks(themessage“InProgress”appears)toadjusttheickering,screenposition,
andscreensizecorrectly.
Whentheautoadjustmentiscompleted,amessageappears.Select“OK”toconrmthenewsettingsor“Cancel”
torestoretheprevioussettings,andpress .
Ifthescreenisnotdisplayedcorrectlyevenafteradjustinginstep3above,performtheadjustments
accordingtotheproceduresonthefollowingpages.Whenthescreenisdisplayedcorrectly,gotostep
5“Toadjustcolorgradationautomatically[RangeAdjustment]”.
17
Chapter 2 Adjusting Screen
4 Perform advanced adjustments for the following using the <Screen> menu of
the <Analog Adjustment>.
Adjusttheclock,phaseandposition,inthisorder.
To eliminate vertical bars [Clock]
Procedure
1. Choose<Clock>fromthe<AnalogAdjustment>menu,andpress .
2. Adjusttheclockwith or .
Press slowlysoasnottomisstheadjustmentpoint.
3. Press toexittheadjustment.
Whenblurring,ickeringorbarsappearonthescreenafteradjustment,proceedto[Phase]toremoveickering
orblurring.
Remove ickering or blurring [Phase]
Procedure
1. Choose<Phase>fromthe<AnalogAdjustment>menu,andpress .
2. Adjustthephasewith or .
3. Press toexittheadjustment.
Attention
• FlickeringorblurringmaynotbeeliminateddependingonyourPCorgraphicsboard.
To correct screen position [Hor.Position] [Ver.Position]
NOTE
• SincethenumberofpixelsandthepixelpositionsarexedontheLCDmonitor,onlyonepositionisprovidedto
displayimagescorrectly.Thepositionadjustmentismadetoshiftanimagetothecorrectposition.
Procedure
1. Choose<Hor.Position>or<Ver.Position>fromthe<AnalogAdjustment>menu,andpress .
2. Adjustthepositionwith or .
3. Press toexittheadjustment.
18 Chapter 2 Adjusting Screen
5 Adjust the color gradation.
To adjust color gradation automatically [Range Adjustment]
Everycolorgradation(0to255)canbedisplayedbyadjustingthesignaloutputlevel.
Procedure
1. DisplayPattern2infullscreenonthemonitorusingthescreenadjustmentpatternles.
2. Choose<RangeAdjustment>fromthe<AnalogAdjustment>menu,andpress .
Thecolorgradationisadjustedautomatically.
Whentheautoadjustmentiscompleted,amessageappears.Select“OK”toconrmthenewsettingsor“Cancel”
torestoretheprecioussettings,andpress .
3. ClosethePattern2.
19
Chapter 2 Adjusting Screen
2-3. Color Adjustment
To select the display mode (CAL Switch)
CALSwitchallowsyoutoselecteasilytheadequatemodesuitableforthemonitor’sapplication.
CAL Switch mode
Mode Purpose
1-DICOM Available to display in DICOM mode.
2-Custom Available for the color settings according to your preference.
3-CAL Displays the screen adjusted by calibration software.
4-Text Suitable for displaying texts for word processing or spreadsheets.
The mode menu
appears.
Procedure
1. Press .
Modemenuappearsatthelowerleftofthescreen.
2. Themodeamongthelistishighlightedinturneachtime ispressed.
Youcanswitchthecurrentmodewith or whilethemodemenuisbeingdisplayed.
1-DICOM←→2-Custom←→3-CAL←→4-Text←
NOTE
• TheAdjustmentmenuandtheModemenucannotbedisplayedatthesametime.
• Youcandisableaspecicmodetobeselected.Formoreinformation,referto“3-1Enabling/DisablingMode
Selection”(page25).
To perform advanced adjustments
The<Color>menuoftheAdjustmentmenuallowsyoutosetandsavetheindependentcoloradjustment
foreachmode.
Attention
• Wait30minutesormorefrommonitorpoweronbeforestartingthecoloradjustment.
(Allowthemonitortowarmupforatleast30minutesbeforemakingadjustments.)
• Performtherangeadjustmentrstwhenadjustingcolorforanaloginputsignals.
(Referto“Toadjustcolorgradationautomatically”onpage18).
• Thesameimagemaybeseenindifferentcolorsonmultiplemonitorsduetotheirmonitor-speciccharacteristics.
Makenecoloradjustmentvisuallywhenmatchingcolorsonmultiplemonitors.
NOTE
• Thevaluesshownin“%”or“K”areavailableonlyasreference.
20 Chapter 2 Adjusting Screen
Adjustment items in each mode
Accordingtothemodeselected,theadjustablefunctiondiffers.
(Youcannotselectanyfunctionunavailableforadjustmentorsetting.)
Theadjustmentsorsettingsmadeforeachmodeareappliedtoallinputsignals.
Fortheadjustmentmethodofeachfunction,refertosubsequentpages.
:Adjustmentavailable―:Invalidforadjustment
Icon Function CAL Switch mode
1-DICOM 2-Custom* 3-CAL* 4-Text*
Brightness √ √
Contrast ― √
Temperature ― √
Gamma ― √
Hue ― √
Saturation ― √
Outline
Enhancer ― √
Gain ― ―
6 Colors ― ―
Color Reset √ √
* Ifyouadjustthecalibrationinthismodeusingthecalibrationkitexclusivefortothismonitor(RadiCSLEasan
accessoryshownonpage45),onlyBrightnessandResetisadjustable.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63

Eizo MX220W Le manuel du propriétaire

Catégorie
Téléviseurs
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues