Eizo RX220 Le manuel du propriétaire

Catégorie
Téléviseurs
Taper
Le manuel du propriétaire
Important
Please read PRECAUTIONS, this Users Manual, and the Setup Manual
(separate volume) carefully to familiarize yourself with safe and
effective usage.
Please refer to the Setup Manual for basic information ranging from
connection of the monitor to a PC to using the monitor.
The latest Users Manual is available for download from our web site:
http://www.eizo.com
Cover
Instructions for Use
Users Manual
2
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
It shall be assured that the nal system is in compliance to IEC60601-1-1 requirement.
Power supplied equipment can emit electromagnetic waves, that could inuence, limit or result in
malfunction of the monitor. Install the equipment in a controlled environment, where such effects are
avoided.
This is a monitor intended for use in a medical imaging system. It does not support the display of
mammography images for diagnosis.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information.
Although every effort has been made to ensure that this manual provides up-to-date information, please
note that EIZO monitor specications are subject to change without notice.
Windows, Windows Vista, Windows Media, SQL Server, and Xbox 360 are registered trademarks of Microsoft Corporation in the
United States and other countries.
A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.
VESA is a registered trademark or a trademark of the Video Electronics Standards Association in the United States and other
countries.
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiForce, RadiCS, RadiNET, Raptor, and ScreenManager are
registered trademarks of EIZO Corporation in Japan and other countries.
All other company and product names are trademarks or registered trademarks of their respective owners.
3
Notice for this monitor
This product is intended to be used in displaying and viewing digital images for diagnosis of X-ray or MRI, etc. by
trained medical practitioners. It does not support the display of mammography images for diagnosis.
This product has been adjusted specically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (Refer to
Cleaning” on the next page.)
The screen may have defective pixels or a small number of light dots on the screen. This is due to the characteristics of
the panel itself, and is not a malfunction of the product.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker, please contact
your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference
patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure
marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.
4
Cleaning
Attention
Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,
and also quality deterioration of the image.
Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
Note
The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with
water.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to
the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
5
CONTENTS
CONTENTS
Cover ............................................................. 1
Notice for this monitor ............................................. 3
CONTENTS ............................................................. 5
Chapter 1 Introduction ....................................... 6
1-1. Features ............................................................ 6
1-2. Switches and Indicators ................................. 7
1-3. Utility Disk ........................................................ 7
Disk contents and software overview ................ 7
To RadiCS LE or ScreenManager Pro for Medical
........................................................................... 7
1- 4. Basic Operation and Functions ..................... 8
Basic operation of Adjustment menu................. 8
Functions ............................................................... 9
Chapter 2 Adjusting Screen ............................. 10
2-1. Setting Screen Resolution ...............................10
Compatible Resolutions/Frequencies ...............10
Setting Resolution ...............................................10
Windows Vista ..................................................10
Windows XP ......................................................10
Mac OS X ..........................................................10
2-2. Displaying Screen Correctly .........................11
Digital Input ..........................................................11
Analog Input .........................................................11
2-3. Color Adjustment ...........................................15
To select the display mode (CAL Switch) .........15
To perform advanced adjustments ...................15
Adjustment items in each mode ........................16
To adjust the brightness [Brightness] ...............17
To adjust the contrast [Contrast] .......................17
To adjust the color temperature [Temperature] 17
To adjust the gamma value [Gamma] ...............18
To adjust the hue [Hue] .....................................18
To adjust the color saturation [Saturation] ........18
To enhance the outline of the image [Outline
Enhancer] ..........................................................19
To adjust the gain value [Gain] ..........................19
To adjust six colors [6 Colors] ...........................19
2-4. Displaying Lower Resolutions..................... 20
To change screen size [Screen Size]............... 20
Chapter 3 Setting Monitor ................................ 21
3-1. Enabling/Disabling Mode Selection [Mode
Preset] .............................................................21
3-2. Locking Switches [Key Lock] .......................21
3-3. Setting the EIZO Logo Display [Logo] ........ 22
3-4. Setting Orientation ...................................... 22
Using Image Rotation Function [Image Rotation]
......................................................................... 22
3-5. Setting Language [Language] ..................... 23
3-6. Setting the Display Position of the
Adjustment Menu [Menu Position] .............. 23
3-7. Restoring the Default Setting ...................... 24
To reset color adjustment values [Color Reset] 24
To reset all adjustments to the factory default
settings [All Reset] ............................................24
Chapter 4 Power Saving Function ................... 25
4-1. Setting the Power Saving [Power Save] ..... 25
4-2. Setting Power Indicator [Power Indicator] . 25
Chapter 5 Troubleshooting .............................. 26
Chapter 6 Reference ......................................... 29
6-1. Attaching an Arm .......................................... 29
6-2. Connecting More than Two PCs to the
Monitor ........................................................... 30
To switch the input signal ................................. 30
To set input signal selection [Input Selection] ...31
6-3. Making Use of USB (Universal Serial Bus) . 32
Required System Environment ........................ 32
Connection Procedure (Setup of USB Function) .
......................................................................... 32
6-4. Displaying Monitor Information .................. 33
Displaying signal information [Signal Info] ....... 33
Displaying monitor information [Monitor Info] .. 33
6-5. Specications ................................................ 34
6-6. Glossary ......................................................... 38
6-7. Preset Timing ................................................. 40
FCC Declaration of Conformity ......................... 41
EMC Information ................................................. 42
LIMITED WARRANTY .......................................... 45
6Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO Color Monitor.
1-1. Features
• Resolution: 2M pixels (Portrait : 1200 × 1600 dots (H × V))
• Applicable to DisplayPort (applicable to 8 bit or 10 bit, not applicable to audio signals)
• 3 signal input terminals (DVI-I x 2, DisplayPort x 1)
• CAL Switch function for selecting an optimal calibration mode
“2-3. To select the display mode (CAL Switch)” (page 15)
• DICOM mode (CAL Switch function) (page 38)
• The quality control software “RadiCS LE” (for Windows) used to calibrate the monitor is included
1-3. Utility Disk” (page 7)
• The software “ScreenManager Pro for Medical” (for Windows) to adjust the screen using the mouse
and keyboard is included
1-3. Utility Disk” (page 7)
• Frame Synchronous mode supported (59 - 61 Hz)
• HDCP (High-bandwidth Digital Content Protection)
7
Chapter 1 Introduction
1-2. Switches and Indicators
1 2 3 4 5 6 7
Switch
Adjustment menu
1. switch 5. switch
2. switch 6. switch
3. switch 7. Power Indicator
4. switch
Indicator status Operation status
Green The screen is displayed
Orange Power saving
Off Main Power Switch / Power Switch off
1-3. Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with the monitor. The following table shows the
disk contents and the overview of the software programs.
Disk contents and software overview
The disk includes application software programs for adjustment, and User’s Manual. Refer to “Readme.
txt” le on the disk for software startup procedures or le access procedures.
Item Overview
A “Readme.txt” le
RadiCS LE (for Windows) RadiCS LE is quality control software used to calibrate the
monitor and manage the calibration history. (A PC must be
connected to the monitor with the supplied USB cable.) Refer
to the description later.
ScreenManager Pro for Medical
(for Windows)
A utility software program to control monitor adjustments from
a PC using its mouse and keyboard. (A PC must be connected
to the monitor with the supplied USB cable.) Refer to the
description later.
User’s Manual (PDF le)
To RadiCS LE or ScreenManager Pro for Medical
Refer to the corresponding User’s Manual on the CD-ROM disk in order to install and use the software.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable. For
more information refer to the “6-3. Making Use of USB (Universal Serial Bus)” (page 32).
8Chapter 1 Introduction
1- 4. Basic Operation and Functions
Basic operation of Adjustment menu
1 Displaying Adjustment Menu
Press .
The adjustment menu appears.
Current mode
Menu title
Settings
Menu
Item
2 Adjusting/Setting
1. Choose a menu to adjust/set with , and press .
2. Choose an item to adjust/set with , and press .
3. Adjust/set the selected item with , and press .
3 Exiting
Press a few times.
The adjustment menu nishes.
9
Chapter 1 Introduction
Functions
The following table shows all the Adjustment menu’s adjustment and setting menus.
Main Menu Item Adjusting/Setting
Color Brightness 2-3. Color Adjustment” (page 15)
Contrast
Temperature
Gamma
Advanced
Settings
Hue
Saturation
Outline Enhancer
Gain
6 Colors
Color Reset 3-7. Restoring the Default Setting”
(page 24)
Screen Screen Size 2-4. Displaying Lower Resolutions”
(page 20)
Image Rotaion 3-4. Setting Orientation” (page 22)
Analog
Adjustment
Auto Adjustment “2-2. Displaying Screen Correctly
(page 11)
Range Adjustment
Clock
Phase
Hor.Position
Ver.Position
PowerManager Power Save 4-1. Setting the Power Saving” (page 25)
Power Indicator 4-2. Setting Power Indicator” (page 25)
Menu Settings Language 3-5. Setting Language” (page 23)
Menu Position 3-6. Setting the Display Position of the
Adjustment Menu” (page 23)
Tools Input Selection “6-2. Connecting More than Two PCs to the
Monitor” (page 30)
Mode Preset 3-1. Enabling/Disabling Mode Selection”
(page 21)
Signal Info “6-4. Displaying Monitor Information”
(page 33)
Monitor Info
All Reset 3-7. Restoring the Default Setting”
(page 24)
* The adjusting/setting function on the <Color> menu depend on the selected Color mode (page 16). The above table
shows the sub menus when the “Custom” mode is selected (See “2-3. Color Adjustment” (page 15)).
10 Chapter 2 Adjusting Screen
Chapter 2 Adjusting Screen
2-1. Setting Screen Resolution
Compatible Resolutions/Frequencies
For details on compatible resolutions, refer to “Compatible Resolutions/Frequencies” in the Setup
Manual.
Setting Resolution
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to
change the resolution, follow the procedure below.
Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog, select the “Monitor” tab and select desired resolution in the
“Resolution” eld.
5. Click the “OK” button.
6. When a conrmation dialog is displayed, click “Yes”.
Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog is displayed, click the “Settings” tab and select desired
resolution for “Screen resolution” under “Display.
4. Click the “OK” button to close the dialog.
Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog, select the “Display” tab and select desired resolution in the “Resolutions”
eld.
4. Your selection will be reected immediately. When you are satised with the selected resolution, close
the window.
11
Chapter 2 Adjusting Screen
2-2. Displaying Screen Correctly
Digital Input
When digital signals are input, images are displayed correctly based on the preset data of the monitor.
When performing advanced adjustment, see “2-3 Color Adjustment” (page 15) and subsequent pages.
Analog Input
Attention
Wait 30 minutes or more from monitor power on before starting adjustments.
(Allow the monitor to warm up for at least 30 minutes before making adjustments.)
The monitor screen adjustment is used to suppress ickering of the screen or adjust screen position and
screen size correctly according to the PC to be used.
The auto adjustment function works when lling/satisfying all of the following conditions
When a signal is input into the monitor for the rst time or when the resolution or Vertical/
Horizontal Frequency not displayed before is set
When signals with the vertical resolution over 480 are input
If the screen is not displayed correctly even after performing the auto adjustment, perform the screen
adjustments according to the procedures on the following pages to use the monitor comfortably.
[Adjustment Procedure]
1 Perform the auto adjustment.
To adjust ickering, screen position, and screen size automatically [Auto Adjustment]
Procedure
1. Choose <Screen> from the Adjustment menu, and press .
2. Choose <Analog Adjustment> from the <Screen> menu, and press .
3. Choose <Auto Adjustment>, and press .
The auto adjustment function works (the message “In Progress” appears) to correctly adjust the ickering, screen
position, and screen size correctly.
When the auto adjustment is completed, a message appears. Select “OK” to conrm the new settings or “Cancel”
to restore the previous settings, and press .
Attention
This function works correctly when an image is fully displayed over the Windows or Macintosh display area. It
does not work properly when an image is displayed only on a part of the screen (command prompt window, for
example) or when a black background (wallpaper, etc.) is in use.
This function does not work correctly with some graphics boards.
If the screen is not displayed correctly even after adjusting in step 1 above, perform the adjustments
according to the procedures on the following pages. When the screen is displayed correctly, go to step
5 “To adjust color gradation automatically [Range Adjustment]”.
12 Chapter 2 Adjusting Screen
2 Prepare the display pattern for the analog display adjustment.
Download the “Screen adjustment pattern les” from our site: http://www.eizo.com
NOTE
For details and instructions on opening the “Screen adjustment pattern les”, refer to the “Readme.txt” le.
3 Perform the auto adjustment again with the analog screen adjustment pattern
displayed.
To adjust ickering, screen position, and screen size automatically [Auto Adjustment]
Procedure
1. Display Pattern 1 of the screen adjustment pattern les in full screen on the monitor.
2. Choose <Screen> from the Adjustment menu, and press .
3. Choose <Analog Adjustment> from the <Screen> menu, and press .
To proceed with the subsequent adjustments, select an item in <Analog Adjustment> of the <Screen> menu.
4. Choose <Auto Adjustment>, and press .
The auto adjustment function works (the message “In Progress” appears) to adjust the ickering, screen position,
and screen size correctly.
When the auto adjustment is completed, a message appears. Select “OK” to conrm the new settings or “Cancel”
to restore the previous settings, and press .
If the screen is not displayed correctly even after adjusting in step 3 above, perform the adjustments
according to the procedures on the following pages. When the screen is displayed correctly, go to step
5 “To adjust color gradation automatically [Range Adjustment]”.
13
Chapter 2 Adjusting Screen
4 Perform advanced adjustments for the following using the <Screen> menu of
the <Analog Adjustment>.
Adjust the clock, phase and position, in this order.
To eliminate vertical bars [Clock]
Procedure
1. Choose <Clock> from the <Analog Adjustment> menu, and press .
2. Adjust the clock with or .
Press slowly so as not to miss the adjustment point.
3. Press to exit the adjustment.
When blurring, ickering or bars appear on the screen after adjustment, proceed to [Phase] to remove ickering
or blurring.
Remove ickering or blurring [Phase]
Procedure
1. Choose <Phase> from the <Analog Adjustment> menu, and press .
2. Adjust the phase with or .
3. Press to exit the adjustment.
Attention
Flickering or blurring may not be eliminated depending on your PC or graphics board.
To correct screen position [Hor.Position] [Ver.Position]
NOTE
Since the number of pixels and the pixel positions are xed on the LCD monitor, only one position is provided to
display images correctly. The position adjustment is made to shift an image to the correct position.
Procedure
1. Choose <Hor.Position> or <Ver.Position> from the <Analog Adjustment> menu, and press .
2. Adjust the position with or .
3. Press to exit the adjustment.
14 Chapter 2 Adjusting Screen
5 Adjust the color gradation.
To adjust color gradation automatically [Range Adjustment]
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
Procedure
1. Display Pattern 2 in full screen on the monitor using the screen adjustment pattern les.
2. Choose <Range Adjustment> from the <Analog Adjustment> menu, and press .
The color gradation is adjusted automatically.
When the auto adjustment is completed, a message appears. Select “OK” to conrm the new settings or “Cancel”
to restore the precious settings, and press .
3. Close the Pattern 2.
15
Chapter 2 Adjusting Screen
2-3. Color Adjustment
To select the display mode (CAL Switch)
CAL Switch allows you to select easily the adequate mode suitable for the monitor’s application.
CAL Switch mode
Mode Purpose
1-DICOM Available to display in DICOM mode.
2-Custom Available for the color settings according to your preference.
3-CAL Displays the screen adjusted by calibration software.
4-Text Suitable for displaying texts for word processing or spreadsheets.
The mode menu
appears.
Procedure
1. Press .
Mode menu appears at the lower left of the screen.
2. The mode among the list is highlighted in turn each time is pressed.
You can switch the current mode with or while the mode menu is being displayed.
1-DICOM←→2-Custom←→3-CAL←→4-Text←
NOTE
The Adjustment menu and the Mode menu cannot be displayed at the same time.
You can disable a specic mode to be selected. For more information, refer to “3-1 Enabling/Disabling Mode
Selection” (page 21).
To perform advanced adjustments
The <Color> menu of the Adjustment menu allows you to set and save the independent color adjustment
for each mode.
Attention
Wait 30 minutes or more from monitor power on before starting the color adjustment.
(Allow the monitor to warm up for at least 30 minutes before making adjustments.)
Perform the range adjustment rst when adjusting color for analog input signals.
(Refer to “To adjust color gradation automatically” on page 14).
The same image may be seen in different colors on multiple monitors due to their monitor-specic characteristics.
Make ne color adjustment visually when matching colors on multiple monitors.
NOTE
The values shown in “%” or “K” are available only as reference.
16 Chapter 2 Adjusting Screen
Adjustment items in each mode
According to the mode selected, the adjustable function differs.
(You can not select any function unavailable for adjustment or setting.)
The adjustments or settings made for each mode are applied to all input signals.
For the adjustment method of each function, refer to subsequent pages.
: Adjustment available ―: Invalid for adjustment
Icon Function CAL Switch mode
1-DICOM 2-Custom* 3-CAL* 4-Text*
Brightness √ √
Contrast ― √
Temperature ― √
Gamma ― √
Hue ― √
Saturation ― √
Outline
Enhancer ― √
Gain ― ―
6 Colors ― ―
Color Reset √ √
* If you adjust the calibration in this mode using the calibration kit exclusive for to this monitor (RadiCS LE as an
accessory shown on page 37), only Brightness and Reset is adjustable.
17
Chapter 2 Adjusting Screen
To adjust the brightness [Brightness]
The screen brightness is adjusted by changing the brightness of the backlight (Light source from the LCD
back panel).
Adjustable range: 0 to 100%
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Brightness> from the <Color> menu, and press .
3. Adjust the brightness with or .
4. Press to exit the adjustment.
NOTE
You can also adjust the brightness using and .
When your feel the image is bright even if the brightness is set to 0%, adjust the contrast.
To adjust the contrast [Contrast]
The luminance of the screen is adjusted by varying the video signal level.
Adjustable range: 0 to 100%
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Contrast> from the <Color> menu, and press .
3. Adjust the contrast with or .
4. Press to exit the adjustment.
NOTE
In the contrast of 100%, every color gradation is displayed.
When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the
gradation characteristics, prior to the contrast adjustment.
Perform the contrast adjustment in the following cases.
- When you feel the image is bright even if the brightness is set to 0%. (Set the contrast to lower than 100%).
To adjust the color temperature [Temperature]
The color temperature can be adjusted. The color temperature is normally used to express the hue of
“White” and/or “Black” by a numerical value. The value is expressed in degrees “K” (Kelvin). In the
same way as the ame temperature, the image on the monitor is displayed reddish if the color temperature
is low and is bluish if the color temperature is high. The gain preset values are set for each color
temperature setting value.
Adjustable range: Native, 6000K-15000K (specied by every 500K unit, including 9300K)
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Temperature> from the <Color> menu, and press .
3. Adjust the color temperature with or .
4. Press to exit the adjustment.
NOTE
[Gain] allows you to perform more advanced adjustment (See “To adjust the gain value” on page 19).
If you set to [Native], the image is displayed in the preset color of the monitor (Gain: 100% for each RGB).
When changing the gain value, the color temperature adjusting range is changed to “User.
18 Chapter 2 Adjusting Screen
To adjust the gamma value [Gamma]
The gamma value can be adjusted. The luminance of the monitor varies depending on the input signal,
however, the variation rate is not proportional to the input signal. To keep the balance between the input
signal and the luminance of the monitor is called as “Gamma correction”.
Adjustable range: 1.8-2.6
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Gamma> from the <Color> menu, and press .
3. Adjust the gamma value with or .
4. Press to exit the adjustment.
To adjust the hue [Hue]
This function allows you to adjust the hue.
Adjustable range: -100 to 100
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Advanced Settings> from the <Color> menu, and press .
3. Choose <Hue>, and press .
4. Adjust the hue with or .
5. Press to exit the adjustment.
Attention
This function does not enable to display every color gradation.
To adjust the color saturation [Saturation]
This function allows you to adjust the saturation of the color on the monitor.
Adjustable range: -100 to 100
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Advanced Settings> from the <Color> menu, and press .
3. Choose <Saturation>, and press .
4. Adjust the saturation of the color with or .
5. Press to exit the adjustment.
Attention
This function does not enable to display every color gradation.
NOTE
Setting the minimum (-100) turns the image to a monochrome screen.
19
Chapter 2 Adjusting Screen
To enhance the outline of the image [Outline Enhancer]
OutlineEnhancer functions to emphasize outline of the images by emphasizing the color difference
between pixels composing the images. This may improve the texture of the material and its feel of the
images. On the contrary, it also functions to reproduce the images smoothly by gradating its outline.
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Advanced Settings> from the <Color> menu, and press .
3. Choose <Outline Enhancer>, and press .
4. Select the display status in the range from -3 to 3 (soft to sharp) with or as desired.
5. Press to exit the adjustment.
To adjust the gain value [Gain]
Each luminance of red/green/blue composing the color is called “Gain”. The gain adjustment may change
the color tone of the “White” (when the max input signal for each color is obtained)
Adjustable range: 0 to 100%
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Advanced Settings> from the <Color> menu, and press .
3. Choose <Gain>, and press .
4. Choose the color for adjustment among <Red>, <Green>, or <Blue> to adjust, and press .
5. Adjust the gain with or .
6. Press to exit the adjustment.
NOTE
The gain value may change depending on the value of the color temperature.
When changing the gain value, the color temperature adjusting range is changed to “User.
To adjust six colors [6 Colors]
The hue and saturation can be adjusted for each of six colors: Magenta, Red, Yellow, Green, Cyan, and
Blue.
Adjustable range: -100 to 100
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Advanced Settings> from the <Color> menu, and press .
3. Choose <6 Colors>, and press .
4. Choose the color for adjustment among <Magenta>, <Red>, <Yellow>, <Green>, <Cyan>, or <Blue>,
and press .
5. Select <Hue> or <Saturation>, and press .
6. Adjust the 6 colors with or .
7. Press to exit the adjustment.
20 Chapter 2 Adjusting Screen
2-4. Displaying Lower Resolutions
To change screen size [Screen Size]
You can change the screen size by using <Screen Size> from <Screen> menu.
Menu Function
Full Displays an image in full screen. Images are distorted in some cases because the
vertical rate is not equal to the horizontal rate.
Enlarged Displays an image in full screen. In some cases, a blank horizontal or vertical border
appears to equalize the vertical rate and the horizontal rate.
Normal
(default setting)
Displays images with the specied resolution.
Example: Image size 1024 x 768
Full Enlarged Normal
(Default setting)
(1200 x 1600) (1200 x 900) (1024 x 768)
Procedure
1. Choose <Screen> from the Adjustment menu, and press .
2. Choose <Screen Size> from the <Screen> menu, and press .
3. Select “Full Screen,” “Enlarged,” or “Normal” with or .
4. Press to exit the adjustment.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53

Eizo RX220 Le manuel du propriétaire

Catégorie
Téléviseurs
Taper
Le manuel du propriétaire

dans d''autres langues