Sony SCD-XA777ES Manuel utilisateur

4-235-066-13(1)

Super Audio CD

Player

 2001 Sony Corporation

SCD-XA777ES

Operating Instructions

Mode d’emploi

US

FR

2

US

Welcome!

Thank you for purchasing the Sony Super

Audio CD Player. Before operating the

unit, please read this manual thoroughly

and retain it for future reference.

About This Manual

The instructions in this manual is for SCD-

XA777ES.

Conventions

• Instructions in this manual describe the

controls on the player.

You can also use the controls on the

remote if they have the same or similar

names as those on the player.

• The following icons are used in this

manual:

Indicates that you can do the

task using the remote.

Indicates hints and tips for

making the task easier.

Z

z

WARNING

To prevent fire or shock

hazard, do not expose the

unit to rain or moisture.

This symbol is intended to alert the

user to the presence of uninsulated

“dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a

risk of electric shock to persons.

This symbol is intended to alert the

user to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

For the customers in the United States

This label is located on the left exterior.

Owner’s Record

The model and serial numbers are located

at the rear of the unit.

Record the serial number in the space

provided below. Refer to them whenever

you call upon your Sony dealer regarding

this product.

Model No. SCD-XA777ES

Serial No. _________________________

CAUTION

The use of optical instruments with this

product will increase eye hazard.

As the laser beam used in this CD player is

harmful to eyes, do not attempt to

disassemble the cabinet. Refer servicing to

qualified personnel only.

For the customers in Canada

This Class B digital apparatus complies

with Canadian ICES-003.

CAUTION

TO PREVENT ELECTRIC SHOCK, DO

NOT USE THIS POLARIZED AC PLUG

WITH AN EXTENSION CORD,

RECEPTACLE OR OTHER OUTLET

UNLESS THE BLADES CAN BE FULLY

INSERTED TO PREVENT BLADE

EXPOSURE.

WARNING

This equipment has been tested and found

to comply with the limits for a Class B

digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This equipment generates,

uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may

cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in

a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be

determined by turning the equipment off

and on, the user is encouraged to try to

correct the interference by one or more of

the following measures:

– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

CAUTION

You are cautioned that any changes or

modification not expressly approved in this

manual could void your authority to

operate this equipment.

3

US

Features

About the Super Audio CD

• Super Audio CD is a new high-quality audio disc

standard where music is recorded in the DSD (Direct

Stream Digital) format (conventional CDs are recorded

in the PCM format). The DSD format, using a sampling

frequency 64 times higher than that of a conventional

CD, and with 1-bit quantization, achieves both a wide

frequency range and a wide dynamic range across the

audible frequency range, and so provides music

reproduction extremely faithful to the original sound.

• The Super Audio CD has two types; a 2 channel stereo

disc and a Multi-channel disc which holds up to 6

independent channels. The multi-channel characteristic

of the Super Audio CD features a speaker allocation

system basically similar to the 5.1 channel output of

current AV systems.

Features of the player

This player is designed to play back 2-channel and multi-

channel Super Audio CDs, and conventional CDs, and

provides the following features:

• Mounted with a Discrete Dual Laser Optical Pickup,

capable of reading a Super Audio CD or conventional

CD depending on the exclusive wavelength.

• Quicker track access performance enabled by an

advanced servo mechanism.

• A Multi-Channel Management function that allows you

to adjust the multi-channel playback environment

according to the allocation and size of your speakers.

• A Super Audio D/A Converter and Direct Digital Sync

System, which allows higher-quality sound

reproduction.

Others

• A Super Audio CD can mark up to 255 track/index

numbers. This feature applies to SCD-XA777ES.

• The supplied remote is capable of controlling both the

SCD-XA777ES and a conventional Sony CD player.

TABLE OF CONTENTS

Getting Started 4

Before You Start the Hookup 4

Hooking Up the Audio Components 5

Location and Functions of Parts 8

Front Panel Parts Descriptions 8

Rear Panel Parts Descriptions 10

Remote Parts Descriptions 11

Playing Discs 12

Compatible Disc Types 12

Playing a Disc 14

Using the Display 15

Locating a Specific Track 18

Locating a Particular Point in a Track 18

Playing Tracks Repeatedly 19

Playing Tracks in Random Order (Shuffle Play) 20

Creating Your Own Program (Program Play) 21

Listening to a CD Using a Filter (Digital Filter

Function) 22

Setting the DIGITAL OUT on/off 22

Selecting the default playback area 22

Listening to a Multi-channel Super Audio CD

(Multi-channel management function) 23

Additional Information 26

Precautions 26

Notes on Discs 27

Troubleshooting 28

Specifications 28

Index 29

4

US

Getting

Started

This chapter provides information on

the supplied accessories and how to

connect various audio components to

the Super Audio CD player. Be sure

to read this chapter thoroughly before

you actually connect anything to the

player.

Before You Start the

Hookup

Checking the supplied accessories

This player comes with the following items:

• Audio connecting cord

phono jack × 2 (Red and White) y phono jack × 2 (Red

and White) (3)

phono jack × 1 (Black) y phono jack × 1 (Black) (2)

• Remote commander RM-SX700 (1)

• Size AA (R6) batteries (2)

• AC power cord (1)

• Plug adapter (1)

Inserting batteries into the remote

Insert two size AA (R6) batteries into the battery

compartment with the + and – correctly oriented to the

markings. When using the remote, point it at the remote

sensor

on the player.

z

When to replace the batteries

Under normal conditions, the batteries should last for about six

months. When the remote no longer operates the player, replace

both batteries with new ones.

Notes

• Do not leave the remote in an extremely hot or a humid place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not use a new battery with an old one.

• Do not expose the remote sensor to direct sunlight or lighting

apparatus. Doing so may cause a malfunction.

• If you do not intend to use the remote for an extended period

of time, remove the batteries to avoid possible damage from

battery leakage and corrosion.

5

US

Getting Started

ANALOG

L

LR

RR

L

5.1CH OUT

2CH OUT

OUT

OPTICALCOAXIAL

CENTER

FRONT SURROUND SUB WOOFER

DIGITAL(CD)

AC IN

Hooking Up the Audio Components

White (L)

Red (R)

White (L)

Red (R)

Connect the Super Audio CD player to an audio

component. Be sure to turn off the power of all

components before making connections and connect

securely to prevent noise.

When you have an amplifier equipped with the 5.1CH

input jacks (multi-channel amplifier, AV amplifier, etc.)

and connect the player and the amplifier via ANALOG

5.1CH OUT jacks, you can play a multi-channel Super

Audio CD and enjoy the multi-channel playback.

For normal playback, connect the player and an amplifier

via ANALOG 2CH OUT jacks.

Connecting via ANALOG 5.1CH OUT jacks

Use audio connecting cords for this connection. Connect the

ANALOG 5.1CH OUT jacks (FRONT L/R, SURR L/R, CENTER,

SUBWOOFER) to the corresponding jacks of your amplifier. For

FRONT or SURR connection, use the connecting cords (Red and

White jacks) and be sure to match the color-coded pin to the

appropriate jacks: white (left) to white and red (right) to red. For

CENTER and SUB WOOFER connection, use the connecting

cords (Black).

FRONT or SURR connection

Audio connecting cords (Red and White) (supplied)

Black

CENTER or SUB WOOFER connection

Audio connecting cords (Black) (supplied)

Notes

• When you make the Multi-channel connection, connect the

ANALOG 2CH OUT jacks also using another audio connecting

cord so that you can play a CD (or SACD) when you set the

input selector of your amplifier to CD (or SACD) input .

• During playback of a conventional CD or a 2CH Super Audio

CD, no signal is output from the ANALOG 5.1CH FRONT L/R

jacks. Instead, the signal is output in high quality from the

ANALOG 2CH OUT jacks (see page 7).

• During playback of a Multi-channel Super Audio CD, no signal

is output from the ANALOG 2CH OUT jacks.

• There are 5CH, 4CH, and 3CH Super Audio CD. When you

play these disc, the signal does not output from all the jacks of

the ANALOG 5.1CH OUT. For details of the playback, see the

cover or instructions of the Super Audio CD.

To FRONT IN

jacks (L/R)

To SURROUND or

REAR IN jacks

(L/R)

To CENTER IN

jack

To SUB WOOFER

IN jack

Multi-channel amplifier,

AV amplifier, etc.

6

US

Getting Started

ANALOG

L

LR

RR

L

5.1CH OUT

2CH OUT

OUT

OPTICALCOAXIAL

CENTER

FRONT SURROUND SUB WOOFER

DIGITAL(CD)

AC IN

Connecting via ANALOG 2CH OUT jacks

Use an audio connecting cords for this connection. Connect the

ANALOG 2CH OUT L/R jacks to the CD (SACD) input jacks of

your amplifier. Be sure to match the color-coded pin to the

appropriate jacks: white (left) to white and red (right) to red.

Audio connecting cords (Red and White) (supplied)

White (L)

Red (R)

White (L)

Red (R)

To CD (SACD) IN

jacks (L/R)

Stereo amplifier, etc.

Hooking Up the Audio Components

Note

During playback of a Multi-channel Super Audio CD, no signal is

output from the ANALOG 2CH OUT jacks.

About the ANALOG 2CH OUT

When you play a conventional CD or a 2CH Super Audio CD, the

stereo signal is sent to the FRONT, SURROUND, and CENTER/

SUB WOOFER D/A Converters, and each signal is combined

after D/A conversion, then combined signal is output from the

2CH OUT jacks.

Since each digital signal is converted to analog signal by three

converters, this system offers a three-fold improvement in a

signal quality and a root three-fold in noise ratio, and results in

improvement in a signal to noise ratio. Therefore, the high

quality signal is output from the ANALOG 2CH OUT jacks.

However, because of the system, no signal is output from the

ANALOG 2CH OUT jacks during playback of a Multi-channel

Super Audio CD. Similarly, no signal is output from the PHONES

jack during playback of a Multi-channel Super Audio CD.

7

US

Getting Started

Connecting via DIGITAL (CD) OUT OPTICAL

connector

Use an optical digital cable for this connection. When connecting

the optical digital cable to the DIGITAL (CD) OUT OPTICAL

connector, take the cap off the connectors and push the cable

plugs in until they click into place.

Be careful not to bend or twist the optical cable.

Optical digital cable (not supplied)

Note

Only the audio signals of conventional CDs can be output from

the DIGITAL (CD) OUT connectors. Those of the Super Audio

CD cannot be output through DIGITAL (CD) OUT.

Connecting via DIGITAL (CD) OUT COAXIAL

connector

Use a coaxial digital cable to connect the audio components

equipped with coaxial digital input connectors.

Coaxial digital cable (not supplied)

Note

Only the audio signals of conventional CDs can be output from

the DIGITAL (CD) OUT connectors. Those of the Super Audio

CD cannot be output through DIGITAL (CD) OUT.

Connecting the AC power cord

Connect the supplied AC power cord to the AC IN terminal on

the player and to the mains.

Note on the ANALOG output jacks

This player is equipped with a Tri-Powered D/A Converter

System and a Multi Channel Management function. The usable

output settings differ depending on the mode you select as

follows. For details, refer to the Operating Instructions.

Source

CD

Super Audio CD

(2 channel)

Super Audio CD

(Multi-channel)

Note on 2 channel playback of Super Audio CDs

If you select “2ch + SW,” the output setting becomes 3 channel

and the playback sound is output from the 5.1 CH OUT jacks.

Therefore, no sound is output from the 2 CH OUT jacks or

PHONES jack.

Multi Channel

Managment

Not available when

playing back CDs

Direct

2ch + SW

Direct

Except Direct

2CH OUT

jacks

a

×

5.1CH OUT

jacks

×

a

PHONES

jack

a

×

About the AC power cord

The supplied AC power cord has a 3-pronged grounded plug. If

you are using 3-pronged grounded mains, the plug can be

inserted directly into the mains. However, if the socket is a 2-

pronged grounded mains, use the supplied plug adapter or a

commercially available plug adapter.

3-pronged grounded mains

2-pronged polarized mains

• When the width of the mains are a different size

Use the supplied plug adapter.

• When the width of the mains are the same size

Use a commercially available plug adapter. In this case, you

can check the polarity of the mains with a commercially

available spark-testing screwdriver. It is the pronged ground

that does not light the neon grow lamp even if you insert the

spark-testing screwdriver into the mains. Insert the blades so

that the “N pole” can be inserted to the ground on the plug.

If noise (hum) is produced

Noise may be caused by an electric potential difference on the

ground circuit.* In this case, use the supplied plug adapter and be

careful not to connect the ground lead to anything.

* Although the ground of the domestic mains is normally a

safety ground, a few electrical potential differences may be

produced, depending on the mains. Therefore, use of the

supplied 3-pronged mains lead may lessen the quality of the

audio signal or may produce humming noise.

3 to 2-prong polarized

plug adapter

N pole

8

US

Location and

Functions of

Parts

This chapter tells you about the

location and functions of the various

buttons and controls on the front and

rear panels and the supplied remote.

Further details are provided on the

pages indicated in parentheses.

It also tells you about the information

that appears in the display window.

Front Panel Parts

Descriptions

1 POWER switch (14)

Press to turn on the player.

2 Remote sensor

(4)

3 Disc tray (14)

Press A OPEN/CLOSE to open/close the disc tray.

4 A OPEN/CLOSE button (14)

Press to open the disc tray.

5 PHONES

Connect the headphones.

During playback of a Multi-channel Super Audio CD,

no signal of the Multi-channel signal is output from

the PHONES jack (see page 7).

6 PHONE LEVEL

Adjust the headphones volume.

9

US

Location and Functions of Parts

7 TIME/TEXT button (15)

Each time you press the button, the playing time of the

track, the total remaining time on the disc, or TEXT

information appears in the display.

8 MENU (13)

Press to enter the menu.

9 MULTI/2CH button (with an LED) (14)

Each time you press the button while the 2 channel +

Multi-channel Super Audio CD (page 13) is loaded,

the playback area changes between the multi-channel

playback area (the LED turns on) and 2 channel

playback area (the LED turns off).

0 SACD/CD button (with an LED) (14)

Each time you press the button while the Hybrid disc

(page 13) is loaded, the layer changes between the HD

layer (the LED turns on) and CD layer (the LED turns

off).

qa Display window (15)

Shows various information.

qs N button (14)

Press to start play.

N indicator

Lights up during playback.

qd X button (14)

Press to pause play.

X indicator

Lights up during pause.

qf x button (14)

Press to stop play.

qg l AMS L dial (AMS: Automatic Music Sensor)

(18)

When you turn the l AMS L dial

counterclockwise by one click, you go back to the

preceding track; when you turn the l AMS L

dial clockwise by one click, you go to the succeeding

track.

POWER

PHONES

PHONE LEVEL

MIN MAX

TIME/TEXT SACD/CD

OPEN/CLOSE

AMS

PUSH ENTER

MULTI/2CHMENU

10

US

Location and Functions of Parts

Rear Panel Parts Descriptions

1 ANALOG 5.1CH OUT jacks (5)

Connect to an amplifier equipped with the 5.1CH

input jacks (Multi-channel amplifier, AV amplifier,

etc.) using the audio connecting cords.

2 DIGITAL (CD) OUT COAXIAL connector (7)

Connect to an audio component using the coaxial

digital cable.

3 DIGITAL (CD) OUT OPTICAL connector (7)

Connect to an audio component using an optical

digital cable.

4 AC IN terminal (7)

Connect the AC power cord.

5 ANALOG 2CH OUT L/R jacks (6)

Connect to an audio component (stereo/2 channel)

using the audio connecting cord.

Note

Only the audio signals of the CD can be output from the

DIGITAL (CD) OUT connectors shown in 2 and 3. Those of the

Super Audio CD cannot be output through DIGITAL (CD) OUT.

ANALOG

L

LR

RR

L

5.1CH OUT

2CH OUT

OUT

OPTICALCOAXIAL

CENTER

FRONT SURROUND SUB WOOFER

DIGITAL(CD)

AC IN

11

US

Location and Functions of Parts

Remote Parts Descriptions

CONTINUE SHUFFLE

PLAY MODE

PROGRAM

SACD/CD

123

456

78

10/0

9

TIME/TEXT

REPEAT

AMS

BA

CLEAR

>10 ENTER

MODE

DISPLAY/

MULTI/2CH

INDEX

LEVEL

ADJ

CHECK

1 CONTINUE button (20)

Press to resume normal play from Shuffle Play or

Programme Play.

SHUFFLE button (20)

Press to select Shuffle Play.

PROGRAM button (21)

Press to select Programme Play.

2 DISPLAY MODE button (16)

Press to turn off the information.

3 TIME/TEXT button (15)

Each time you press the button, the playing time of the

track, the total remaining time on the disc, or TEXT

information appears in the display.

4 Number buttons (18)

Press to enter the track numbers.

5

i

10 button (18)

Press to locate a track numbered over 10.

6 REPEAT button (19)

Press repeatedly to play all tracks or only one track on

the disc.

7 AyB button (20)

Press to select Repeat A-B Play.

8 H button (14)

Press to start play.

X button (14)

Press to pause play.

x button (14)

Press to stop play.

9 AMS ./> (AMS: Automatic Music Sensor)

buttons (18)

Press to locate a specific track.

0 m/M buttons (18)

Press to locate a portion you want to play within a

track.

qa INDEX >/. buttons (18)

Press to locate a specific point marked with an index

signal when you play a disc that has index signals.

qs SACD/CD button (14)

Each time you press the button, ”SACD“ or ”CD“

appears in the display. Select the type of CD you want

to play.

qd MULTI/2CH button (14)

Press to select the playback area when the 2 channel +

Multi-channel Super Audio CD (page 13) is loaded.

qf ENTER button (25)

Press to decide the selection.

qg CLEAR button (21)

Press to delete a programmed track number.

qh LEVEL ADJ button (25)

Press to adjust the output level balance for the Multi-

channel management function (page 23).

qj CHECK button (21)

Press to check the programmed order.

12

US

Compatible Disc Types

You can play the following discs with this player.

Depending on the type of disc to be played, select the

appropriate indicator by pressing SACD/CD or MULTI/

2CH (pages 14).

Classification by the layer configuration

Super Audio CD (single layer disc)

This disc consists of a single HD (high density) layer.

When you play this disc, the player is set to the Super

Audio CD playback mode automatically.

Super Audio CD (dual layer disc)

This disc consists of dual HD layers and is capable of

extended play over long periods.

When you play this disc, the player is set to the Super

Audio CD playback mode automatically.

Also, as the dual layer disc consists of dual HD layers on

one side only, it is not necessary to turn the disc over.

Conventional CD

This disc is the standard format.

When you play this disc, the player is set to the

Conventional CD playback mode automatically.

HD (Super Audio CD)

layer

HD (Super Audio CD)

layer

HD (Super Audio CD)

layer

CD layer

Playing Discs

This chapter explains the various

ways to play discs.

Playing Discs

13

US

Super Audio CD + CD (Hybrid disc)

This disc consists of an HD layer and a CD layer. Press

SACD/CD to select the layer you want to listen to. Also,

as the dual layers are on one side, it is not necessary to

turn the disc over. You can play the CD layer using a

conventional CD player.

Classification by the channel

configuration of the Super Audio CD

2 channel Super Audio CD

This disc consists of the 2 channel playback area.

When you play this disc, the player is set to the 2 channel

playback mode automatically.

Multi-channel Super Audio CD

This disc consists of the multi-channel playback area.

When you play this disc, the player is set to the multi-

channel playback mode automatically.

2 channel playback area

Multi-channel playback

area

2 channel + Multi-channel Super Audio CD

This disc consists of the 2 channel playback area and the

multi-channel playback area.

Press MULTI/2CH to select the playback area you want to

listen to.

Selecting the default playback area

(2 channel playback or multi-channel playback

area)

1 During stop mode, press MENU.

2 Tur n l AMS L until “M/2CH SELECT” appears

in the display.

3 Press l AMS L.

The current playback area appears.

4 Tur n l AMS L to select desired playback area,

then press l AMS L.

Incompatible Discs

This player cannot play the following discs. If you try to

play them, the error message “TOC Error” or “No Disc”

will appear or there will be no sound.

• CD-ROM

• DVD, etc.

2 channel playback area

Multi-channel playback

area

CD layer

HD (Super Audio CD)

layer

Playing Discs

14

US

Playing a Disc

The operations for normal play and the basic operations

during play are explained below.

1 Turn on the amplifier. Turn down the volume level

to the lowest.

2 Select the player position using the input selector

on the amplifier.

3 Press POWER to turn on the player.

4 Press A OPEN/CLOSE to open the disc tray, and

place a disc on the tray.

5 Press SACD/CD to select the SACD or CD.

Each time you press the button, the SACD or CD

appears alternately in the display. Select the type of

disc on the tray. For details, see page 12.

6 Press N.

Playback starts from the first track. If you want to start

playing from a specific track, turn lAMSL to

select the track number before pressing N.

7 Adjust the volume on the amplifier.

SACD/CD

lAMSL

POWER

A OPEN/CLOSEN

Xx

With the label side up

Basic operations during play

To Press

Stop play x

Pause play X

Resume play after pausing X or N

Locate a succeeding track Turn lAMSL clockwise

Locate the beginning of the Turn lAMSL

current track or a preceding counterclockwise

track

Eject the disc A OPEN/CLOSE

z

If you turn on the player when a disc is already loaded

Playback starts automatically. If you connect a commercially

available timer, you can set it to start playing the disc at any time

you want.

z

To select a layer you want to listen to when playing a hybrid

disc (page 13)

After you stop play using x, press SACD/CD repeatedly to light

either the “SACD” or “CD.”

z

To select a playback area you want to listen to when playing

a 2 channel + Multi-channel Super Audio CD (page 13)

After you stop play using x, press MULTI/2CH repeatedly to

light either the “MULTI CH” or “2 CH.”

Note

During playback, increase the volume level gradually starting

from the lowest level. The output from this unit may contain

band width that are out of the normal listening range. This may

cause damage to the speakers or ears.

Playing Discs

15

US

Using the Display

The display window shows various information about the

disc or track being played. This section describes the

current disc information and information that appears for

each play status.

TIME/TEXT

DISPLAY MODE

lAMSL

MENU

or

Disc information when a disc is loaded

Depending on the disc that is currently loaded, the

display shows as follows:

2 channel Super Audio CD

Multi-channel Super Audio CD

Conventional CD

or

During playback

a 5.1 channel

Super Audio CD

During playback

a 5 channel

Super Audio CD

During

playback

other Super

Audio CDs or

during stop

mode

Displaying information while the player is

stopped

Press TIME/TEXT.

The display shows the total number of tracks and total

playing time,.

Total playing time

Total number of tracks

CD

SUPER AUDIO

2CH

123

4

678

9

16 17 18 1

9

CD

SUPER AUDIO

MULTI 5.1 CH

1234

6789

16 17 18 1

CD

SUPER AUDIO

MULTI 5 CH

123

4

678

9

16 17 18 1

CD

SUPER AUDIO

MULTI CH

123

4

678

9

16 17 18 1

CD

1234

6789

16 17 18 1

10 45.28

TRACK DISC MIN SEC

CD

SUPER AUDIO

MULTI CH

12345

678910

16 17 18 19 20

TIME/TEXT

Playing Discs

16

US

111.57

TRACK MIN SEC

CD

SUPER AUDIO

INDEX

MULTI 5.1 CH

12345

678910

16 17 18 19 20

-43.32

MIN SEC

CD

SUPER AUDIO

MULTI 5.1 CH

12345

678910

16 17 18 19 20

[MULTI] 5.1 CH

TRACK

CD

SUPER AUDIO

MULTI 5.1 CH

12345

678910

16 17 18 19 20

1-1.56

TRACK MIN SEC

CD

SUPER AUDIO

MULTI 5.1 CH

12345

678910

16 17 18 19 20

SONY BAND 

TEXT ARTIST

CD

SUPER AUDIO

MULTI CH

12345

678910

16 17 18 19 20

10 45.28

TEXT TRACK MIN SEC

CD

SUPER AUDIO

MULTI CH

12345

678910

16 17 18 19 20

SONYHITS 

TEXT DISC

CD

SUPER AUDIO

MULTI CH

12345

678910

16 17 18 19 20

Displaying information while the player is

playing

Press TIME/TEXT.

Each time you press the button, the current track number

and its elapsed time or remaining time appears, or the

total remaining time for the disc appears in the display.

When the player detects a Multi-channel Super Audio

CD, the channel information appears before the default

display appears.

Turning off the information in the display

Z

Each time you press DISPLAY MODE on the remote while

playing a disc, the display turns off and on alternately.

Even when the display is turned off, the display turns on

if you pause or stop play. When you resume play, the

display turns off again.

Before you start playing, when you press DISPLAY

MODE to turn off the display, “Display Off” appears, and

when you press the button to turn on the display,

“Display On” appears.

Playing track number and elapsed playing time of

the current track (default display)

Press TIME/TEXT

Playing track number and remaining time of

the current track

Total remaining time on the disc

Press TIME/TEXT

Channel information (appears only when the player

detects a Multi-channel Super Audio CD)

Using the Display

Displaying the information of a TEXT disc

TEXT discs contain information, such as the disc name or

artist name, as well as the audio signals. This player can

display the disc name, artist name, and current track

name as TEXT information.

When the player detects a TEXT disc, “TEXT” appears in

the display. If your TEXT disc has several languages,

“TEXT” and “MULTI” appear in the display. When you

want to check the information in another language, see

“Displaying the information of a TEXT disc in other

languages” on page 17.

Displaying the information of a TEXT disc

in stop mode

Press TIME/TEXT.

Each time you press the button, the disc name or artist

name appears in the display. When you select the artist

name, “ARTIST” appears in the display.

• Before you start playing

Disc title

Artist name

Total number of tracks and total playing time

Press TIME/TEXT

Press

TIME/

TEXT

Playing Discs

17

US

HITECHBLUES 

TEXT TRACK

CD

SUPER AUDIO

MULTI 5.1 CH

12345

678910

16 17 18 19 20

111.56

TEXT TRACK MIN SEC

CD

SUPER AUDIO

INDEX

MULTI 5.1 CH

12345

678910

16 17 18 19 20

 -43.32

TEXT MIN SEC

CD

SUPER AUDIO

MULTI 5.1 CH

12345

678910

16 17 18 19 20

1-1.57

TEXT TRACK MIN SEC

CD

SUPER AUDIO

MULTI 5.1 CH

12345

678910

16 17 18 19 20

[MULTI] 5.1 CH

TRACK

CD

SUPER AUDIO

MULTI 5.1 CH

12345

678910

16 17 18 19 20

Display information of a TEXT disc while

playing a disc

The current track name appears. If the disc name has

more than 15 characters, the first 14 characters will remain

after the name scrolls by in the display.

When the player detects a Multi-channel Super Audio

CD, the channel information appears before the playing

time of the current track appears.

• While playing a disc

Notes

• The display may not show all the characters, depending on the

disc.

• This player can display only the disc name, artist name, and

track names from TEXT discs. Other information cannot be

displayed.

Remaining time on the current track

Remaining time on the disc

Playing time of the current track

Track title

Press TIME/TEXT

Press

TIME/

TEXT

Press TIME/TEXT

Channel information (appears only when the player

detects a Multi-channel Super Audio CD)

Displaying the information of a TEXT disc

in other languages

You can change the displayed language if the TEXT disc

has multi language capacity. When the player detects such

a TEXT disc, “TEXT” and “MULTI” appear in the display.

Change the language according to the procedures below.

1 Press MENU in stop mode.

2 Tur n l AMS L until “LANGUAGE” appears in

the display.

3 Press l AMS L.

The current selected language (English, French,

German, etc.) flashes.

If the player cannot display the language used in a

TEXT disc, “Other Lang” appears in the display.

4 Tur n l AMS L until the desired language

appears in the display.

5 Press l AMS L.

After a few seconds, the information appears in the

selected language.

Playing Discs

18

US

Locating a Specific Track

During stop or play mode, you can locate any track to be

played.

lAMSL

Number

buttons

./>

>10

To locate

The next or

succeeding tracks

The current or

preceding tracks

A specific track directly

You need to

Turn l AMS L clockwise until

you find the track. When using the

remote, press > repeatedly until you

find the track.

Turn l AMS L counterclockwise

until you find the track. When using the

remote, press . repeatedly until you

find the track.

Turn l AMS L until you find the

track number you want. When using

the remote, press . or >

repeatedly until you find the track.

Locating a track directly by entering the

track number Z

Press the number button(s) to enter the track number.

z

To enter a track number over 11

1 Press >10.

2 Enter the corresponding digits.

To enter 0, press 10/0 instead.

Examples:

• To play track number 30, press >10, then 3 and 10/0.

• To play track number 100, press >10 twice, then 1, and 10/0

twice.

Locating a Particular Point

in a Track Z

You can locate a particular point in a track during play or

play pause.

Locating a point while monitoring the

sound (Search)

Press and hold m/M during play.

You will hear intermittent playback as the disc goes

forward or reverses.

When you reach the desired point, release the button.

Locating a point by observing the time

indication (High-Speed Search)

Press and hold m/M during play pause.

You will not hear the playback sound.

z

When “Over!!” appears in the display

The disc has reached its end. Press . or m to go back.

Note

Tracks that are only a few seconds long may be too short for

monitoring. In this case, the player may not search correctly.

Locating a point using the index function

(Index Search)

Press INDEX. or INDEX> repeatedly in play or

pause mode.

z

What is an INDEX?

Some SACD or CD are provided with an index marking system

which divides tracks or discs into smaller segments. This is

especially useful when you want to locate a certain point within a

long track (in classical music for example). The index search

function works only when you use a commercially available

indexed discs (usually indicated on the label).

./>

m/M

INDEX

>/.

H

Playing Discs

19

US

Locating a point by setting the start time

(Time Search)

1 Press ./> to select the desired track in stop

mode.

2 Press and hold m/M to set the time to start play

while looking at the display.

You can set the time from the beginning of the desired

track when you press M at first, and set the time

from the end of the desired track backward’s when

you press m at first.

3 Press H.

Play will start at the time search.

The player repeats

All the tracks in sequence

All the tracks in random order

All the tracks in the program in

sequence

Playing Tracks Repeatedly

Z

You can play an entire disc or portions thereof repeatedly.

This function can be used with Shuffle Play to repeat all

the tracks in random order (page 20), or with Program

Play to repeat all the tracks in a program (page 21). You

can also repeat a specific track or portion within a track.

Note

If you turn off the player or disconnect the mains lead, the player

will store the last setting of repeat play (“Repeat All” or “Repeat

1”) and recall it the next time you turn on the player. However,

the setting of the Repeat A-B Play will be cancelled if you turn off

the player or disconnect the mains lead.

Repeating all the tracks on the disc

(Repeat All Play)

Press REPEAT once, then press H.

“REPEAT” appears in the display and Repeat All Play

starts.

The repeat play changes depending on the play mode you

select.

When the play mode is

Normal play (page 14)

Shuffle Play (page 20)

Program Play (page 21)

To stop Repeat All Play

Press x.

To resume normal play

Press REPEAT repeatedly until “REPEAT” goes off.

H

AyB

x

REPEAT

52.57

TRACK MIN SEC

CD

SUPER AUDIO

MULTI 5.1 CH

12345

678910

16 17 18 19 20

Playing Discs

20

US

Repeating the current track

(Repeat 1 Play)

While the track you want to repeat is being played,

press REPEAT repeatedly until “REPEAT 1” appears in

the display.

Repeat 1 Play starts.

To stop Repeat 1 Play

Press x.

To resume normal play

Press REPEAT repeatedly until “REPEAT 1” goes off.

Repeating a specific portion within a

track (Repeat A-B Play)

You can specify one portion within a track to be played

repeatedly. Note that the portion that you specify must be

within the boundaries of a single track.

1 While the player is playing, press AyB at the

starting point (point A) of the portion to be played

repeatedly.

“REPEAT” appears and “A” flashes in the display.

2 Continue playing the track (or press M) to locate

the ending point (point B), then press AyB.

“REPEAT A-B” appears and Repeat A-B Play starts.

To stop Repeat A-B Play and resume normal play

Press REPEAT or x.

z

You can set a new starting point and ending point during

Repeat A-B Play

You can change the current ending point to a new starting point,

then specify a new ending point to repeat another portion right

after the current portion.

1 During Repeat A-B Play, press AyB.

The current ending point changes to the new starting point

(point A).

“REPEAT” lights up and “A” flashes in the display.

2 Locate the new ending point (point B) and press AyB.

“REPEAT A-B” lights up and the player starts to repeat the

newly specified portion.

When you want to restart from the starting point A, press H

during AyB repeat.

Playing Tracks Repeatedly Z

Playing Tracks in Random

Order (Shuffle Play) Z

When you select Shuffle Play, the player plays all the

tracks on the disc in random order.

1 Press SHUFFLE in stop mode.

2 Press H.

Shuffle Play starts.

“;” appears while the player is “shuffling” the tracks.

The player will stop after playing all the tracks once.

To resume normal play

Press CONTINUE.

z

You can locate tracks during Shuffle Play

Press ./>.

Press > to locate the next track or press . to locate the

beginning of the current track. The player does not go back to

tracks which have already been played.

H

CONTINUE

SHUFFLE

./>

La page est en cours de chargement...

Sony SCD-XA777ES Manuel utilisateur

Sony SCD-XA777ES Manuel utilisateur

dans d''autres langues

Documents connexes