Samsung DVD-C550 Manuel utilisateur

Marque: Samsung

Modèle: DVD-C550

Catégorie: Lecteurs DVD

Taper: Manuel utilisateur

ENGLISH

DVD Player

User Manual

AK68-01899A

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at

www.samsung.com/global/register

DVD-C500

DVD-C550

DVD-C550K

Precautions

1. Setting up

- Refer to the identification label located on

the rear of your player for its proper

operating voltage.

- Install your player in a cabinet with adequate

ventilation holes. (7~10cm). Do not block

ventilation holes on any of the components

for air circulation.

- Do not push the disc tray in by hand.

- Do not stack components.

- Be sure to turn all components off before

moving the player.

- Before connecting other components to

this player, be sure to turn them off.

- Be sure to remove the disc and turn off the

player after use, especially if you are not

going to use it for a long time.

- The mains plug is used as a disconnect

device and shall stay readily operable at

any time.

2. For your safety

- This product utilizes a laser. Use of

controls or adjustments or performance of

procedures other than those specified

herein may result in hazardous radiation

exposure.

- Do not open covers and do not repair your

self. Refer servicing to qualified personal.

3. Caution

- Your player is not intended for industrial

use but for domestic purposes. Use of this

product is for personal use only.

- Apparatus shall not be exposed to dripping

or splashing and no objects filled with

liquids, such as vases, shall be placed

on the apparatus.

- Exterior influences such as lightning and

static electricity can affect normal

operation of this player. If this occurs, turn

theplayer off and on again with the POWER

button, or disconnect and then reconnect the

AC power cord to the AC power outlet. The

player will operate normally.

- When condensation forms inside the player

due to sharp changes in tempera- ture,

the player may not operate correctly. If this

occurs, leave the player at room tempera-

ture until the inside of the player becomes

dry and operational.

4. Disc

- Do not clean disc using record-cleaning

sprays, benzene, thinner, or other volatile

solvents that may cause damage to the

disc surface.

- Do not touch the disc’s bottom. Hold by the

edges or by one edge and the hole in the

center.

- Wipe the dirt away gently; never wipe a

cloth back and forth over the disc.

5. Environmental info

- The battery used in this product contains

chemicals that are harmful to the environment

- So, dispose the batteries in the proper-

manner, according to federal, state, and

local regulations.

The product unit accomparied this user manual is

licenced under certain intellectual property rights

of certain third parties. This licence is limited to

private non-commercial use by end-user consum-

ers for licenced contents. No rights are granted for

commercial use. The licence does not cover any

product unit other than this product unit and the

licence does not extend to any unlicenced product

unit or pro-cess conforming to ISO/OUR 11172-3

or ISO/OUR 13818-3 used or sold in combination

with this product unit. The licence only covers the

use of this product unit to encode and/or decode

audio files conforming to the ISO/OUR 11172-3 or

ISO/OUR 13818-3. No rights are granted under

this licence for product features or functions that

do not conform to the ISO/OUR 11172-3 or ISO/

OUR 13818-3.

CAUTION: USE OF ANY CONTROLS,

ADJUSTMENTS, OR PROCEDURES OTHER

THAN SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE

Table of contens

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . . 2

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Tour of the Remote Control. . . . . . . . . . . . . . . . . 3

Connections

Choosing a Connection . . . . . . . . . . . . . . . . . . . 4

Basic Functions

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Using the Search and Skip Functions . . . . . . . . 5

Using the Display Function . . . . . . . . . . . . . . . . 6

Using the Disc and Title Menu . . . . . . . . . . . . . . 6

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Advanced Functions

Adjusting the Aspect Ratio (EZ View) . . . . . . . . . 6

Selecting the Audio Language . . . . . . . . . . . . . . 7

Selecting the Subtitle Language . . . . . . . . . . . . . 7

Changing the Camera Angle . . . . . . . . . . . . . . . . 7

Using the Bookmark Function . . . . . . . . . . . . . . . 7

Using the Zoom Function . . . . . . . . . . . . . . . . . . 7

Clips Menu for MP3/WMA/JPEG/MPEG4/

CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . 7

MP3/WMA/CD Audio Playback . . . . . . . . . . . . . . 7

MPEG4 Playback

. . . . . . . . . . . . . . . . . . . . . . . . . 8

Playing Media Files using the USB HOST

feature (Only DVD-C550/DVD-C550K) . . . . . . . . 9

CD Ripping (Only DVD-C550/DVD-C550K) . . . . 9

Picture CD Playback . . . . . . . . . . . . . . . . . . . . . . 9

Picture CD Playback for HD-JPEG . . . . . . . . . . 10

Karaoke Functions

(Only DVD-C550K)

Karaoke Functions . . . . . . . . . . . . . . . . . . . . . . 10

Changing Setup Menu

Using the Setup Menu . . . . . . . . . . . . . . . . . . . . 10

Setting Up the Display Options . . . . . . . . . . . . . 10

Setting Up the Audio Options . . . . . . . . . . . . . . 11

Setting Up the System Options . . . . . . . . . . . . . 12

Setting Up the Language Features . . . . . . . . . . 12

Setting Up the Security Options . . . . . . . . . . . . 12

Setting Up the General Options . . . . . . . . . . . . 13

Setting Up the Support Options . . . . . . . . . . . . 13

Reference

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 13

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Excellent Sound

Dolby Digital, a technology developed by Dolby

Laboratories, provides crystal clear sound reproduction.

Screen

Both regular and widescreen(16:9) pictures can

be viewed.

Slow Motion

An important scene can be viewed in slow motion.

1080p Playback

This player upconverts regular DVDs for playback

on 1080p TVs.

Parental Control (DVD)

The parental control allows users to set the neces-

sary level to prohibit children from viewing harmful

movies such as those with violence, adult subject

matter, etc.

Various On-Screen Menu

Functions

You can select various languages (Audio/Subtitle)

and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture

with double the scan lines of a conventional inter-

laced picture

General Features

Setup

EZ VIEW (DVD)

Easy View enables picture adjustment to match

your TV’s screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by press-

ing the REPEAT button

MP3/WMA

This unit can play discs contain MP3/WMA files.

MPEG4

This unit can play MPEG4 formats within an avi file.

HDMI (High Definition Multimedia

Interface)

HDMI reduces picture noise by allowing a pure-

digital video/audio signal path from the player to

your TV.

CD Ripping (Only DVD-C550/

DVD-C550K)

This feature lets you to copy audio files from disc

to USB device into MP3 format. (Only Audio CD

(CD DA)).

Note

- Discs which cannot be played with this player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• CDGs play audio only, not graphics.

- Ability to play back may depend on recording

conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

- The unit may not play certain CD-R, CD-RW

and DVD-R due to the disc type or recording

conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection.

Because of this, you should only connect your DVD

player directly to your TV, not to a VCR. Connecting

to a VCR results in a distorted picture from copy-pro-

tected DVD discs.

This product incorporates copyright protection technol-

ogy that is protected by methods claims of certain U.S.

patents and other intellectual property rights owned by

Rovi Corporation and other rights owners. Use of this

Rovi Corporation, and is intended for home and other

limited viewing uses only unless otherwise authorized

by Rovi Corporation. Reverse engineering or disas-

sembly is prohibited.

PROGRESSIVE SCAN OUTPUTS

(576p,720p,1080p)

“CONSUMERS SHOULD NOTE THAT NOT ALL

HIGH DEFINITION TELEVISION SETS ARE

FULLY COMPATIBLE WITH THIS PRODUCT AND

MAY CAUSE ARTIFACTS TO BE DISPLAYED

IN THE PICTURE, IN CASE OF 576, 720, 1080

PROGRESSIVE SCAN PICTURE PROBLEMS, IT

IS RECOMMENDED THAT THE USER SWITCH

THE CONNECTION TO THE ‘STANDARD

DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS

REGARDING YOUR TV SET COMPATIBILITY WITH

THIS MODEL 576p, 720p, 1080p DVD PLAYER,

PLEASE CONTACT SAMSUNG’S CUSTOMER

SERVICE CENTER.”

Description

Front Panel Controls

Region Number

Both the DVD player and the discs are coded

by region. These regional codes must match

in order for the disc to play. If the codes do not

match, the disc will not play.

The Region Number for this player is described

on the rear panel of the player.

Disc Markings

Play Region Number

PAL broadcast system in U.K,

France, Germany, etc.

Dolby Digital disc

Stereo disc

Digital Audio disc

DTS disc

MP3 disc

DIGITAL

SOUND

STEREO

PAL

Tour of the Remote Control

DivX Certification

DivX, DivX Certified,

and associated logos are trademarks of

DivXNetworks, Inc and are used under license.

“DivX Certified to play DivX video, including

premium content.”

1. DISC TRAY

Place the disc here.

2. DISPLAY

Operation indicators are displayed here.

3. OPEN/CLOSE (

)

Press to open and close the disc tray.

4. STOP ( )

Stops play.

5. PLAY/PAUSE ( )

Play or pause the disc.

6. POWER ON/OFF ( )

Turn on/off and the player is turned on/off.

7. USB HOST (Only DVD-C550/

DVD-C550K)

Connect digital still camera, MP3 player,

memory stick, Card reader other removable

storage devices.

8. MICROPHONE VOLUME

(Only DVD-C550K)

Use to adjust microphone volume level. Use

the button by pressing it. Turn it to the left or

right to control the volume.

9. MIC 1/2 (Only DVD-C550K)

Connect Microphone for karaoke functions.

DVD-C500

DVD-C550K

DVD-C550

DVD-C500

DVD-C550

DVD-C550K

Choosing a Connection

Connections

The following shows examples of connections commonly used to connect the DVD player with a TV and

other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components you are connecting for more information on

those particular components.

A. Connecting to a TV (For Video)

Using video/audio cables, connect the VIDEO (yellow)/AUDIO (red and white) OUT terminals or 5.1CH

(Front L-R) on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of TV.

Turn on the DVD player and TV.

Press the input selector on your TV remote control until the Video signal from the DVD player appears on

the TV screen.

Note

- Noise may be generated if the audio cable is too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page.

- The number and position of terminals can vary depending on your TV set. Please refer to the user’s

manual of the TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the

DVD player.

- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video

Output mode changes in the following sequence: (I-SCAN ➝ P-SCAN)

B. Connection to a TV (Interlace/Progressive)

Using component video cables, connect the COMPONENT VIDEO OUT terminal on the rear of the DVD

player to the COMPONENT IN terminal of TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals or 5.1CH (Front L-R) on the

rear of the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the DVD player and TV.

Press the input selector on your TV remote control until the Component signal from the DVD player

appears on the TV screen.

Set the Video Output to I-SCAN/P-SCAN in the Display Setup menu. You can use the VIDEO SEL. button

to change the Video Output mode.

Note

- What is “Progressive Scan”?

Progressive scan has twice as many scanning lines as the interlace output method has. Progressive

scanning method can provide better and clearer picture quality.

C. Connecting to a TV with DVI/HDMI Jack

Using the HDMI-DVI/HDMI-HDMI cable , connect the HDMI OUT ter-minal on the rear of the DVD player to

the DVI/HDMI IN terminal of your TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals or 5.1CH (Front L-R) on the rear

of the DVD player to the AUDIO (red and white) IN terminals of your TV. Turn on the DVD player and TV.

Press the input selector on your TV remote control until the DVI/HDMI signal from the DVD player appears

on your TV screen.

HDMI VIDEO Specifications

When you press the HDMI SEL. button, 480p, 576p, 720p, 1080p, 1080i are selected in order.

The first press of the HDMI SEL. button brings up the current resolution.

The second press allows you to change the HDMI output resolution.

- Depending on your TV, certain HDMI output resolutions may not work.

- Please refer to the user’s manual of your TV.

- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10 seconds.

- If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture quality.

- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this

DVD player using your TV remote control. This is only available with Samsung TVs that support

Anynet+(HDMI-CEC).

- If your TV has an

logo, then it will Supports the Anynet+ Function.

• HDMI (High Definition Multimedia Interface)

HDMI is an interface to enable the digital transmission of video and audio data with just a single

connector.Using HDMI, the DVD player transmits a digital video and audio signal and displays a

vivid picture on a TVhaving an HDMI input jack.

• HDMI connection description HDMI connector

- Both uncompressed video data and digital audio data (LPCM or Bit Stream data).- Though the

player uses a HDMI cable, the player outputs only a pure digital signal to the TV.

- If TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears

on the screen.

• Why does Samsung use HDMI?

Analog TVs require an analog video/audio signal. However, when playing a DVD, the data trans-

mitted to a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an

analog-to-digital converter (in the TV) is required. During this conver-sion, the picture quality is

degraded due to noise and signal loss. DVI technology is superior because it requires no D/A con-

version and is a pure digital sig-nal from the player to your TV.

• What is the HDCP?

HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content outputted via

DVI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a

display device (TV, projector . etc). Content is encrypted at the source device to prevent unauthorized.

1. DVD POWER Button

Turns the power on or off.

DVD Button

Use to select the DVD player for operation.

3. TV Button

Use to select a Samsung TV for operation.

4. EZ VIEW Button

Lets you easily adjust the aspect ratio of a

picture according to the screen size of your

TV (16:9 or 4:3).

MARKER Button

6. REPEAT Button

Allows you to repeat play a title, chapter,

track, or disc.

7. DISC MENU Button

Brings up the Disc menu.

8. INFO Button

Used to displays playback info banner.

9. TV VOL (+, -) Buttons

Controls volume.

10. SKIP Buttons ( / )

Use to skip the title, chapter or track.

11. STOP Button ( )

12. MENU Button

Brings up the DVD player’s menu.

13. ENTER//,¥/ Buttons

This button functions as a toggle switch.

14. TOOLS Button

Displays the current disc mode. It also lets

you access the Display function.

15. OPEN/CLOSE (

) Button

To open and close the disc tray.

16. HDMI SEL. Button

HDMI Output resolution setup.

17. USB Button (Only DVD-C550/

DVD-C550K)

ZOOM Button (Only DVD-C500)

Enlarge the DVD Picture.

18. VIDEO SEL. Button

Changes video output mode.

19.

REPEAT A-B Button

Allows you to repeat play a chosen section

(A-B) on a disc.

20.

SUBTITLE Button

21.

TITLE MENU Button

Brings up the Title menu.

22.

AUDIO/TV SOURCE Button

Use this button to access various audio

functions on a disc.

Use this button to select

an available TV source (mode TV).

23. PAUSE Button ( )

Pauses disc play.

24. SEARCH Buttons ( / )

Allows you to search forward/backward

through a disc.

25. TV CH ( , ) Buttons

Channel selection.

26. PLAY Button ( )

Begins disc play.

27. RETURN Button

Returns to a previous menu.

28. EXIT Button

Exits the on-screen menu.

29.

KARAOKE (



) Button

(Only DVD-C550K)

Use to begin Karaoke functions.

D. Connection to an Audio System (2 Channel Amplifier, Dolby Digital,

MPEG2 or DTS Amplifier)

1. Using the audio cables, connect the AUDIO (red and white) OUT terminals or 5.1CH (Front L-R) on the

rear of the DVD player to the AUDIO (red and white) IN terminals of the Amplifier. If using a coaxial cable,

connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD player to the DIGITAL

AUDIO IN (COAXIAL) terminal of the Amplifier.

2. Using the video signal cable(s), connect the VIDEO, COMPONENT or HDMI OUT terminals on the rear of

the DVD player to the VIDEO, COMPONENT or DVI IN terminals of your TV

3. Turn on the DVD player, TV, and Amplifier.

4. Press the input select button of the Amplifier to select external input in order to hear sound from the DVD

player. Refer to your Amplifier's user manual to set the Amplifier's audio input.

E. Connection to a 5.1CH Analog Amplifier (Only DVD-C550K)

1. If using audio cables for 5.1 CH Analog Amplifier connect the 5.1CH ANALOG AUDIO OUT terminals on

the rear of the DVD player to the 5.1CH ANALOG AUDIO

IN terminals of the 5.1CH Analog Amplifier.

2. Using the video signal cable(s), connect the VIDEO,

COMPONENT or HDMI OUT terminals on the rear of the

DVD player to the VIDEO, COMPONENT or DVI IN termi-

nals of your TV

3. Turn on the DVD player, TV, and Amplifier.

4. Press the input select button of the Amplifier to select

external input in order to hear sound from the DVD player.

Refer to your Amplifier's user manual to set the Amplifier's

audio input.

Playing a Disc

Basic functions

Before Play

Turn on your TV and set it to the correct Video Input by pressing TV/VIDEO button on the TV remote

control.

- If you connected an external Audio System, turn on your Audio System and set it to the correct

Audio Input.

After plugging in the player, the first time you press the DVD POWER button, this screen comes up: If you want

to select a language, press

the  button, and then press the ENTER

button. (This screen will only appear

when you plug in the player for the first time.)If the language for the startup screen is not set, the set-tings may

change whenever you turn the power on or off. Therefore, make sure that you select the language you want to

use.Once you select a menu language, you can change it by pressing the

■

/|| button on the front panel of the

unit for more than 5 seconds with no disc in the unit. Then the SELECT MENU LANGUAGE window appears

again where you can reset your preferred language.

Using the Search and Skip Functions

During play, you can search quickly through a chapter or track, and use the skip function to jump to the

next selection.

Searching through a Chapter or Track

During play, press the SEARCH (k or K) button on the remote control for more than 1 second.

Note

- The speed marked in this function may be different from the

actual playback speed.

- No sound is hearing during search mode (Except CD).

Skipping Tracks

During play, press the SKIP (|k or K|) button.

- When playing a DVD, if you press the SKIP (

) button, it moves to the next chapter. If you press

the SKIP (

) button, it moves to the beginning of the chapter. One more press makes it move to the

beginning of the previous chapter.

- When playing a VCD, if you press the SKIP (

) button, it moves to the next track. If you press the

SKIP (

) button, it moves to the beginning of the track. One more press makes it move to the begin-

ning of the previous track.

- If a track exceeds 15 minutes when playing a VCD and you press the

button, it moves forward 5

minutes. If you press the

button, it moves to the beginning of the track. One more press makes it

move to the beginning of the previous track.

BLACK

5.1ch Analog

Amplifier

BLACK

RED

WHITE

RED WHITE

DVD-C500

DVD-C550

DVD-C550K

Coaxial Cable

Dolby digital or DTS

ampilfier

Audio Cable

RED

HDMI cable

WHITE

RED WHITE

HDMI-DVI cable

YELLOW

Video

Cable

Component

Cable

YELLOW

RED

BLUE

GREEN

RED

BLUE

GREEN

Coaxial Cable

Dolby digital or DTS

ampilfier

Audio Cable

HDMI cable

WHITE

RED WHITE

HDMI-DVI cable

YELLOW

Video

Cable

Component Cable

YELLOW

RED

BLUE

GREEN

RED

BLUE

GREEN

RED

Audio Cable

WHITE

RED

WHITE

RED

WHITE

RED

RED WHITE

2-Channel stereo amplifier

Audio Cable

DVD

VCD

2X, 4X, 8X, 16X, 32X

4X, 8X

Using the Disc and Title Menu

During the playback of a DVD disc, press the DISC MENU/TITLE MENU button on the remote control.

Note

- Depending on a disc, the Disc Menu/Title Menu may not work.

- You can also use the Disc Menu, using the DISC MENU button on the remote control.

- Title Menu will only be displayed if there are at least two titles in the disc.

Repeat Play

Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc.

When playing a DVD/VCD

1. Press the REPEAT button on the remote control. Repeat screen appears.

2. Press the REPEAT or  button to change playback mode.

DVD repeats play by chapter or title.

- Chapter : repeats the chapter that is playing.

- Title : repeats the title that is playing.

- Off.

Note

A-B REPEAT allows you to set point (B) directly after point (A) has been set.

- Depending on a disc, the Repeat function may not work.

Slow Play

This feature allows you slowly to repeat scenes con-taining sports, dancing, musical instruments

being played etc., so you can study them more closely.

When playing a DVD

During play, press the PAUSE (∏∏) button.

Press the SEARCH (k/K) button to choose the play speed between 1/2, 1/4, 1/8 and 1/16 of normal dur-

ing PAUSE mode.

Adjusting the Aspect Ratio (EZ View)

Advanced functions

To play back using aspect ratio (DVD)

1. During play, press the EZ VIEW button on the remote control.

2. Press the EZ VIEW or  buttons to select the screen size. Each time you press the EZ VIEW or 

buttons, the screen size changes. For graphics of the screen sizes and lists of the sequences in which the

sizes change, see the next column.

Press the EXIT button to exit EZ View.

If you are using a 16:9 TV

For 16:9 aspect ratio discs

- WIDE SCREEN

- SCREEN FIT

- ZOOM FIT

For 4:3 aspect ratio discs

- Normal Wide

- SCREEN FIT

- ZOOM FIT

- Vertical Fit

If you are using a 4:3 TV

For 16:9 aspect ratio discs

- 4:3 Letter Box

- 4:3 Pan Scan

- SCREEN FIT

- ZOOM FIT

For 4:3 aspect ratio discs

- Normal Screen

- SCREEN FIT

- ZOOM FIT

Using the Display Function

When Playing a DVD/VCD/MPEG4

During play, press the TOOLS button on the remote control.

Press the  buttons to select the desired item.

Press the ¥ buttons to make the desired setup.

To make the screen disappear, press the

TOOLS

button again.

Note

This function may behave differently depending on the type of disc.

The functions when using the Display function are listed in the table below.

To access the desired title when there is more than one in the disc. For example, if there is

more than one movie on a DVD, each movie will be identified.

Most DVD discs are recorded in chapters so that you can quickly find a specific passage.

Allows playback of the film from a desired time. You must enter the starting time as a refer-

ence.The time search function does not operate on some disc.

Refers to the language of the film soundtrack. In the example, the soundtrack is played in

English 5.1CH. A DVD disc can have up to eight different soundtracks.

Refers to the subtitle languages available in the disc. You will be able to choose the subtitle languag-

es or, if you prefer, turn them off from the screen. A DVD disc can have up to 32 different subtitles.

User will be able to choose EZ-View type.

Press enter to activate the Zoom function.

To access the desired Angle function.

Some DVD disc are have more than one recorded angle.

Using the A-B Repeat function

1. Press the REPEAT A-B button on the remote control.

2. Press the REPEAT A-B button at the point where you want repeat play to start (A).

Press the REPEAT A-B button at the point where you want the repeat play to stop (B).

3. To return to normal play, press the REPEAT A-B

button until the display shows Repeat : Off

Note

The subtitle languages are represented by abbreviations.

- You have to change the desired subtitle in the Disc Menu, according to discs. Press the DISC MENU button.

- This function depends on what subtitles are encoded on the disc and may not work on all DVDs.

- A DVD disc can contain up to 32 subtitle languages.

Changing the Camera Angle

When a DVD contains multiple angles of a particular scene, you can use the ANGLE function.

Using the ANGLE function (DVD)

If the disc contains multiple angles, the ANGLE appears on the screen.

During play, press the TOOLS button on the remote control.

Press the

/

buttons to select icon. When the angle screen is displayed, press the ¥buttons on

the remote control to select the desired angle option.

Using the Bookmark Function

This feature lets you bookmark sections of a DVD or VCD (Menu Off mode) so you can quickly find

them at a later time.

Using the Bookmark Function (DVD/VCD)

During play, press the MARKER button on the remote control.

When you reach the scene you want to mark, press the

¥/

/

buttons, and then press

MARKER

button.

Up to 12 scenes may be marked at a time.

Recalling a Marked Scene

During play, press the MARKER button on the remote control.

Press the

¥/or /

buttons to select a marked scene.

Press the PLAY () button to skip to the marked scene.

Clearing a Bookmark

During play, press the MARKER button on the remote control.

Press the

¥/

or/

buttons to select the bookmark number you want to delete.

Press the ENTER button to delete a bookmark number.

Using the Zoom Function

Using the Zoom Function (DVD/VCD)

1. During play or pause mode, press the TOOLS

ZOOM button on the remote control.

2. Press the

/

buttons to select icon, then press the ENTER button to zoom in X1,X2,X3,X4.

Clips Menu for MP3/WMA/JPEG/MPEG4/CD Audio

CD Audio or discs with MP3/WMA/JPEG/MPEG4 contain individual songs and/or pictures that can be

organized into folders as shown below. They are similar to how you

use your computer to put files into different folders.

To go access these folders and the files in them, follow these steps :

Open the disc tray. Place the disc on the tray.

Close the tray. The tray closes and the Parent Folder Menu screen

appears

(top screen image.) Parent folders contain all the Peer folders that

have the same kind of content: music, video, photos, etc.

Press the

¥/

buttons to select the Parent folder of your choice, and then press the ENTER. A screen

displaying the Peer folders appears. The Peer folders contain all the folders with the same kind of content

(video, music, photos, etc.) that are in the Parent folder.

Folder Selection

The folder can be selected both in Stop or Play mode.

- To select the Parent Folder

Press the RETURN button to go to parent folder, or press the  buttons to select “..” and press ENTER to

go to the parent folder.

- To select the Peer Folder

Press the  buttons to select the desired folder, then press ENTER.

- To select the Sub-Folder

Press the  buttons to select the desired folder, then press ENTER.

Note

- This function depends on audio languages are encoded on the disc and may not work.

- A DVD disc can contain up to 8 audio languages.

Selecting the Subtitle Language

You can select a desired subtitle quickly and easily with the SUBTITLE button.

Using the SUBTITLE button (DVD/MPEG4)

1. During play,

Press the SUBTITLE button.

Press the SUBTITLE or button to change the language. Each time you press the SUBTITLE or

 button, the language changes.

3. To remove the

SUBTITLE

icon, press the EXIT button.

Selecting the Audio Language

You can select a desired audio language quickly and easily with the AUDIO button.

Using the AUDIO button (DVD/VCD/MPEG4)

During play, Press the AUDIO button. Change the audio language by pressing the AUDIO or  button.

- The audio languages are represented by abbreviations.

To remove the AUDIO icon, press the EXIT button.

Note

- Depending on a disc, the Bookmark function may not work.

MP3/WMA/CD Audio Playback

Open the disc tray. Place the disc on the tray. Close the tray.

Press the

¥/

buttons to select a Music Menu then press ENTER. Press the

/

buttons t to select

a song file then press the ENTER

Press the

/

buttons to begin playback of the song file then press

ENTER.

Videos \ 1/2 Pages

CD Pages Move Return

CD-R MP3/WMA file

When you record MP3 or WMA files on CD-R, please refer to the following.

- Your MP3 or WMA files should be ISO 9660 or JOLIET format.

ISO 9660 format and Joliet MP3 or WMA files

are compatible with Microsoft’s DOS and Windows, and with

Apple’s Mac. This format is the most widely used.

When naming your MP3 or WMA files, do not exceed 8 characters, and enter “.mp3, .wma” as the file extension.

General name format : Title.mp3. or Title.wma. When composing your title, make sure that you use 8 charac-

ters or less, have no spaces in the name, and avoid the use of special characters including: (.,/,\,=,+).

- Use a decompression transfer rate of at least 128 Kbps when recording MP3 files.

Sound quality with MP3 files basically depends on the rate of compression/decompression you choose.

Getting CD audio sound requires an analog/digital sampling rate, that is conversion to MP3 format, of at least

128 Kbps and up to 160 Kbps. However, choosing higher rates, like 192 Kbps or more, only rarely give better

sound quality. Conversely, files with decompression rates below 128 Kbps will not be played properly.

- Use a decompression transfer rate of at least 64Kbps when recording WMA files.

Sound quality with WMA files basically depends on the rate of compression/decompression you choose.

Getting CD audio sound requires an analog/digital sampling rate, that is conversion to WMA format, of at

least 64Kbps and up to 192Kbps. Conversely, files with decompression rates below 64Kbps or over 192Kbps

will not be played properly. Sampling rate that can be supported for WMA files is > 30Khz.

- Do not try recording copyright protected MP3 files.

Certain “secured” files are encrypted and code protected to prevent illegal copying. These files are of the fol-

lowing types: Windows Media

(registered trade mark of Microsoft Inc) and SDMI

(registered trade mark of

The SDMI Foundation). You cannot copy such files.

- Important:

The above recommendations cannot be taken as a guarantee that the DVD player will play MP3 recordings,

or as an assurance of sound quality. You should note that certain technologies and methods for MP3 file

recording on CD-Rs prevent optimal playback of these files on your DVD player (degraded sound quality and

in some cases, inability of the player to read the files).

- This unit can play a maximum of 500 files and 500 folders per disc.

MPEG4 Playback

MPEG4 Play Function

AVI files are used to contain the audio and video data. Only AVI format files with the “.avi” extensions can

be played.

Open the disc tray. Place the disc on the tray. Close the tray

Press the ¥/ buttons to select a Videos Menu ,

then press the ENTER

. Press

the

/ to select

an avi file

(DivX/XviD) then press the

ENTER

Press

the

/

and then press the ENTER button.

Note

A-B REPEAT allow you to set point (B) directly after point (A) has been set.

MPEG4 Function Description

Function Description

Skip

(|k or K|)

During play, press the

|k or K|

button, it moves to next or previous track.

(k or K)

During play, press the SEARCH (

k or K

) button and press again to search at a faster

speed. Allows you to search at a faster speed in an AVI file. (2X, 4X, 8X, 16X, 32X)

Slow Motion Play Allows you to search at a slower speed in an AVI file. (1/2, 1/4, 1/8, 1/16)

ZOOM

X1/X2/X3/X4/Normal in order

CD-R AVI fileThis

unit can play the following video compression formats

within the AVI file format:

- DivX 3.11 contents

- DivX 4 contents (Based on MPEG-4 Simple Profile)

- DivX 5 contents (MPEG-4 simple profile plus addi

tional features such as bi-directional frames. Qpel

and GMC are also supported.)

- XviD MPEG-4 compliant Contents.

DVD-RW & DVD+R

Format that support for DivX file :

- Basic DivX format DivX3.11 / 4.12/ 5.x

Xvid (MPEG-4 compliant video codec) and DivX Pro

- File format : *.avi, *.div, *.divx.

This unit supports all resolutions up to maximum

below.

DivX5

720 x 480 @30fps

720 x 576 @25fps:

Maximum bitrate : 4Mbps

Repeat/Random playback

Press the REPEAT button to change the playback mode. There are four modes, such as Off, Track,

Folder and Random.

- Off

(

)

: Normal Playback

- Track

(

)

: Repeats the current song ﬁ le.

- Folder

(

)

: Repeats the song ﬁ les which have the same extension in the current folder.

- Random

(

)

: Song ﬁ les which have the same extension will be played in random order.

To resume normal play, press the

REPEAT

button until the Repeat : Off.

- These functions may not work depending on MPEG4 file.

Possible warning messages that may appear when

trying to play DivX/AVI files are :

No Authorization

- File with bad registration code.

Unsupported Codec

- Files with certain Codec Types, Versions

(ex. MP4, AFS and other proprietary codecs)

are not suppoerted by this player.

Unsupported Resolution

- Files containing resolutions higher than the

player’s specification are not supported.

Note

• The resolution that can be supported by

DVD-C500/C550/C550K model up to 720 x

480 @30 frames/ 720 x 576 @25 frames.

• This unit supports CD-R/RW written in

MPEG4 in accordance with the “ISO9660

format”.

Repeat and Repeat A-B playback

Press the REPEAT button , then press

REPEAT

/

buttons to change playback mode. There

are 3 modes, such as Off, Folder and Title.

- Folder : repeats the AVI files which have the same extension in the current folder.

- Title : repeats the title that is playing.

- Off : No Repeat mode.

Press the REPEAT A-B button

on the remote control.

3. Press the

REPEAT A-B

button to set the point where you want repeat play to start (A).

Press the REPEAT A-B button again at the point where you want the repeat play to stop (B).

- To return to normal play, press the REPEAT A-B

button until the display shows Repeat : Off

Fast playback

To play back the disc at a faster speed, press (k/K) during playback

•

Each time you press either button, the playback speed will change as follows : 2X ➞ 4X ➞ 8X ➞ 16X ➞ 32X.

Compatible Devices

1. USB devices that support USB Mass Storage v1.0.(USB devices that operate as a removable disk in

Windows (2000 or later) without additional driver installation.)

2. MP3 Player: Flash type MP3 player.

3. Digital camera: Cameras that support USB Mass Storage v1.0.

• Cameras that operate as a removable disk in Windows (2000 or later) without additional driver installation.

4. USB Flash Drive: Devices that support USB2.0 or USB1.1.

• You may experience a difference in playback quality when you connect a USB1.1 device.

5. USB card Reader: One slot USB card reader and Multi slot USB card reader

• Depending on the manufacturer. the USB card reader may not be supported.

• If you install multiple memory devices into a multi card reader, you may experience problems.

6. If you use a USB extension cable, the USB device might not be recognized.

• CBI (Control/Bulk/Interrupt) is not supported.

• Digital Cameras that use PTP protocol or require additional program installation when connected to a PC are

not supported.

• A device using NTFS file system is not supported. (Only FAT 16/32 (File Allocation Table 16/32) file system is

supported.)

• Some MP3 players, when connected to this product,may not operate depending on the sector size of their

file system.

• The USB HOST function is not supported if a product that transfers media files by its manufacturer-specific

program is connected.

• Does not operate with Janus enabled MTP(Media Transfer Protocol) devices.

• The USB host function of this product does not support all USB devices.

Picture CD Playback

Select the desired folder.

Press the

/

buttons to select a Picture file in the clips menu and then press the ENTER button.

Note

- Press the STOP button to return to the clips menu.

- When playing a Kodak Picture CD, the unit displays the Photo directly, not the clips menu.

CD Ripping (Only DVD-C550/DVD-C550K)

This feature allows you to copy audio files from a disc to a USB device in MP3 format.

Open the dics tray. Place the Audio CD(CD DA) disc on the tray, and close the tray. Connect the USB device to

the USB port on the front of the unit. Press the DVD button.

Press the TOOLS button to display the Ripping screen.

Press the / buttons, then press the ENTER button to select files for ripping.

To deselect files, press ENTER button again.

Press the ¥ and



button to select START, then press the ENTER button begin ripping.

The Ripping menu contain the following buttons :

- Mode (Fast/Normal)

- Bitrate, press ENTER to change :

128kbps ➞ 192kbps ➞ 128kbps ...

• Standard : 128kbps

• Better Quality : 192kbps

- Device selection, press ENTER to change between partitions on the USB device (max 4).

- Select - Unselect, press ENTER to change from Select all (files) or Select none.

Note

- To cancel copying in progress, press the ENTER button.

- To return to CDDA screen, press the TOOLS button again.

- When the CD ripping being processed the player will automatic in play mode.

- Ripping process is 2.6 times of normal speed.

- Only the Audio CD(CD DA) dics can be ripping.

- The USB button does not work while you’re in the Ripping menu.

- CD ripping function may not supported for some MP3 players device.

Playing Media Files Using the USB Host feature

(Only DVD-C550/DVD-C550K)

You can enjoy the media files such as pictures, movies andtunes saved in an MP3 player, USB memory or

digital camera in high audio by connecting the storage device to the USB port of the DVD Player.

Using the USB HOST feature

Connect the USB device to the USB port on the front of the unit.

The USB Menu screen appears. Press the ¥/ button to select Menu, then press ENTER.

Press the / buttons to select a file in the USB device. Press ENTER to Open the file.

Note

•

Each time the USB button on the remote control is pressed, a frame of the USB device selection will appear.

• “USB” appears on the display screen.

•

Depends on the file size and clip duration, loading time on USB may take longer than using CD or DVD media.

• USB MENU screen appears on the TV screen and the saved file is played.

•

If there is a Disc in the unit, pressing the DVD button will make the player exit the USB menu and load the disc.

Safe USB Removal

Press the DVD button to return to disc mode or the main screen.

Press the STOP (■) button

Remove the USB cable.

Skip Forward/Back

During playback, press the (|k/K|) button.

• When there is more than one file, when you press the K| button, the next file is selected.

• When there is more than one file, when you press the |k button, the previous file is selected.

Rotation

- Press the TOOLS button to select Rotate, and then press the ENTER button.

Each time the ¥buttons are pressed, the picture rotates 90 degrees clockwise.

Each time the  button is pressed, the picture will reverse to the upside down to show a mirror image.

Each time the  button is pressed, the picture will reverse to the right side to show a mirror image.

Zoom

- Press the TOOLS button

to select

Zoom, and then press the ENTER button..

Each time ENTER button is pressed, the picture is enlarged. Zoom mode : X1-X2-X3-X4-X1.

Slide Show

- When you press the PLAY at JPEG file, it will go to full screen mode and automatically slide show.

Note

Depending on a file size, the amount of time between each picture may be different from the manual.

If you don’t press any button, the slide show will start automatically in about 10 seconds by default.

• Rotation

Press the TOOLS button to select Rotate

, and then press the ENTER button.

Press the ¥/ button to

rotate the screen 90 degrees to the left/right.

• Skip Picture

Press the |k or K| button to select previous or next picture.

• Slide Show

Press the PLAY () button to start SLIDE function.

Press the

PAUSE (∏∏)

button to stop SLIDE function.

Note

- Depending on a file size, the amount of time between each picture may be different from the set

interval time.

- The image may be displayed at a smaller size depending on the picture size when displaying images

in HD-JPEG mode.

- It is recommended to set the “BD Wise” to “Off” In case of playback JPEG image file bigger than

720 X 480 pixel size.

MP3-JPEG Playback

You can play JPEG using music as a backgound.

Press the

/

buttons to select an MP3 file in the clips menu and then press the ENTER button.

To return to the menu screen, Press the RETURN or MENU buttons.

ress the

¥/

buttons to select Photos Menu, and

then press the ENTER button.

Press the

/

buttons to select a JPEG file in the clips menu and then press the ENTER button.

- Music will play from the beginning

3. Press Stop button when you want to stop the playback.

Note

MP3 and JPEG files have to be on the same disc.

CD-R JPEG Disc

- Only files with the “.jpg” and “.JPG” extensions can be played.

- If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.

- Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.

- The name of the JPEG file may not be longer than 8 characters and should contain no blank spaces or special

characters (. / = +).

- Only a consecutively written multi-session disc can be played. If there is a blank segment in the multi-session

disc, the disc can be played only up to the blank segment.

- A maximum of 500 images can be stored on a single CD.

- Kodak Picture CDs are recommended.

- When playing a Kodak Picture CD, only the JPEG files in the pictures folder can be played.

- Kodak Picture CD: The JPEG files in the pictures folder can be played automatically.

- Konica Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.

- Fuji Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.

- QSS Picture CD: The unit may not play QSS Picture CD.

- If the number of files in 1 Disc is over 500, only 500 JPEG files can be played.

- If the number of folders in 1 Disc is over 500, only JPEG files in 500 folders can be played.

Mic Volume and Key Control

Playback the Karaoke Disc containing the wanted songs.

- Press the KARAOKE () button, and then press

/

to select VOL or KEY.

Press the

¥/

buttons to change the desired item.

Using the Setup Menu

Changing setup menu

The Setup menu lets you customize your DVD player by allowing you to select various language prefer-

ences, set up a parental level, even adjust the player to the type of television screen you have.

With the unit in Stop mode, press the MENU button on the remote control. Press the

¥/

buttons to select

SETTINGS, then press the ENTER button.

Press the

/

buttons to select a Setup Menu, then press the



or ENTER to bring up the sub-menu.

Press the

/

buttons to select a sub-menu option, then press the



or ENTER.

To make the setup screen disappear after setting up, press the RETURN button.

Note

- If you hear feedback(squealing or howling) while using the karaoke feature, move the microphone

away from the speakers or turn down the microphone volume or the speaker volume.

- When playing MP3, WMA, DTS and LPCM disc, the karaoke functions will not operate.

- When the MIC is connected, Digital Out does not work.

- The MIC sound outputs only from Analog Audio Out.

- If MIC is connected to the MIC jack on the front panel, 5.1CH audio will be changed in to 2 CH audio

automatically, this condition can’t be change unless the MIC is plugged out.

Picture CD Playback for HD-JPEG

Must connect to HDMI. Resolution should be 720p/1080i/ 1080p, and HD-JPEG should be in HD mode.

Select the desired folder.

Press the  buttons to select a Picture file in the clip menu and then press the ENTER button.

• Press the STOP (■) button to return to the clips menu.

• When playing a Kodak Picture CD, the unit displays the Photo directly, not the clips menu.

Karaoke Functions

Karaoke functions (Only DVD-C550K)

Operation Sequence

Connect the Mixed Audio Out terminals with the TV or Amplifier.

Connect Mic into Mic jack. When a MIC is connected, the karaoke functions can be used.

Setting Up the Display Options

Display options enable you to set various video functions of the player.

With the unit in Stop mode, press the MENU button. Press the

¥/

buttons to select SETTINGS, then

press the ENTER button.

Press the

/

buttons to select DISPLAY, then press the



or ENTER button.

Press the

/

buttons to select the desired item, then press the



or ENTER button.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trade-

marks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

HDMI

- If your TV is not compatible with compressed multi-channel formats (Dolby Digital, DTS,

MPEG), you should set Digital Audio to PCM.

- If your TV is not compatible with LPCM sampling rates over 48kHz, you should set PCM Down

sam-pling to On.

Setting Up the Audio Options

Audio Options allows you to setup the audio device and sound status settings depending on the audio

system in use.

With the unit in Stop mode, press the MENU button. Press the

¥

buttons to select SETTING, then

press the ENTER button.

Press the  buttons to select AUDIO, then press the  or ENTER button.

Press the

/

buttons to select the desired item, then press the



or ENTER button.

Surround Sound Speaker Setup (Only DVD-C550K)

With the unit in Stop mode, press the MENU button. Press the

¥

buttons to select SETTINGS, then

press the ENTER button.

Press the

/

buttons to select AUDIO, then press the



or ENTER button.

Press the

/

buttons to select SPEAKER SETUP, then press the



or ENTER button.

Press the

//¥/

buttons to select the desired item, then press the ENTER button to set the speaker.

Note

•

This option can be changed only when TV support BD Wise.

• Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If

Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan set-

tings in the TV’s menu system.

• If Video Output is set incorrectly, the screen may be blocked.

• The resolutions available for HDMI output depend on the connected TV or projector. For

details, see the user’s manual of your TV or projector.

• When the resolution is changed during playback, it may take a few seconds for a normal

image to appear.

•

If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture

quality.

•

It is recommended to set the "BD Wise" to "Off" In case of playback JPEG image file bigger than 720

X 480 pixel size.

Note :

- When play a disc that has MPEG Audio and you have Bitstream selected in the Audio Options menu,

the Digital Audio jack may not output audio

There is no analogue audio output when you play

a DTS sound disc.

- Even when PCM Down sampling is Off

• Some discs will only output down sampled audio through the digital outputs.

Setting Up the BD Wise

When the player is connected to a SAMSUNG TV which supports “BD Wise”,you can enjoy optimized

Picture Quality by setting the “BD Wise” function as “On”.

With the unit in Stop mode, press the MENU button. Press the

¥/

buttons to select SETTINGS, then

press the ENTER button.

Press the

/

buttons to select DISPLAY, then press the



or ENTER button.

Press the

/

buttons to select BD WISE, then press the



or ENTER button.

Press the

/

buttons to select ON/OFF, then press the ENTER button.

The default settings : FRONT L, R (Small), CENTER (Small), SURROUND (Small). Select the size of the speakers

to be connected.

❶

Front (FL, FR)

- Large

- Small

❷

Center

- None

- Large

- Small

❸

Surround (SL, SR)

- None

- Large (Rear/Side)

- Small (Rear/Side)

Setting up Test

The test output signals come clockwise starting from the Front Speaker(L).

Adjust Channel Balance so that speakers output equally in your room.

FRONT(L) ➝ CENTER ➝ SUBWOOFER ➝ FRONT(R) ➝ SURROUND(R) ➝ SURROUND(L)

Setting Up the Security Options

The Parental Control function works in conjunction with DVDs that have been assigned a rating, which

helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc.

Setting Up the Rating Level and Changing the Password

With the unit in Stop mode, press the MENU button. Press the

¥/

buttons to select SETTINGS, then

press the ENTER button.

Press the

/

buttons to select SECURITY, then press the



or ENTER button. Enter your password.

Press the

/

buttons to select PARENTAL/CHANGE

PASSWORD, then press the  or ENTER button

Press the

/

buttons to select rating level you want, then press the ENTER button.

e.g) Setting up in KID SAFE

For example, if you select the Kids Safe level, discs that contain level 2 or higher will not play.

Enter your password.

If this is the first time, enter 0000. Then, enter a new

password. The new pass-

word must be a number other than 0000 to activate the parental control function. Then, re-enter the new

password.

Security Levels :

❶ KID SAFE

❷ G (General Audiences) : All Ages Admitted

❸

PG (Parental Guidance suggested) : Some material may not be suitable for young children.

❹

PG 13 (PG-13 Parents strongly cautioned) : Some material may be inapproriate for children under 13.

❺

PGR (Parental Guidance Recommended) : These are not necessarily unsuitable for children, but viewer

discretion is advised, and parents and guardians are encouraged to supervise younger viewers.

❻ R (Restricted) : Under 17 requires accompanying adult

❼

NC17 (NC-17) : No one 17 and under admitted.

❽ ADULT

Note:

- If you have forgotten your password, see “Forgot Password” in the Troubleshooting Guide.

Setting Up the System Options

With the unit in Stop mode, press the MENU button. Press the

¥/

buttons to select SETTINGS, then

press the ENTER button.

Press the

/

buttons to select SYSTEM, then press the



or ENTER button.

Press the

/

buttons to select the desired item, then press the



or ENTER button.

Setting Up the Language Features

If you set the player menu, disc menu, audio and subtitle language in advance, they will come up auto-

matically every time you watch a movie.

With the unit in Stop mode, press the MENU button. Press the

¥/

buttons to select SETTINGS, then

press the ENTER button.

Press the

/

buttons to select LANGUAGE, then press the



or ENTER button.

Press the

/

buttons to select the desired language, then press the



or ENTER button.

Note

- The language is selected and the screen returns to Language Setup menu.

- To make the setup menu disappear, press the MENU button.

- If the selected language is not recorded on the disc, the original pre-recorded language is selected.

- Select “Original” if you want the defaultsoundtrack language to be the original language the disc is

recorded in.

- Select “Automatic” if you want the subtitle language to be the same as the language selected as the

audio language.

Some discs may not contain the language you select as your initial language; in that case the disc will use its

original language setting.

Setting Up the Anynet+(HDMI-CEC)

Anynet+ is a function that can be used to operate the unit using a Samsung TV remote control, by con-

necting the DVD C500/C550/C550K to a SAMSUNG TV using a HDMI Cable. (This is only available with

SAMSUNG TVs that support Anynet+.

Select On when you connect the DVD C500/C550/C550K with Samsung TV that support Anynet+.

With the unit in Stop mode, press the MENU button. Press the

¥/

buttons to select SETTINGS, then

press the ENTER button.

Press the

/

buttons to select SYSTEM, then press the



or ENTER button.

Press the

/

buttons to select ANYNET+ (HDMI-CEC), then press the



or ENTER button.

Set the Anynet+(HDMI-CEC) to “On” on your DVD Player, then press the ENTER button

Set the Anynet+ function at your TV. (See the TV instruction manual for more information.

•

When you press Anynet+ button on the TV remote control, the below OSD will appear

Note

• By pressing the PLAY button of the unit while watching TV, the TV screen will change to the play screen.

• If you play a DVD when the TV power is off, the TV will power On.

• If you turn the TV off , the DVD Player will power off automatically.

• If you change the HDMI to other sources (Composite,Component,... etc) in TV while playing the DVD disc, the

DVD Player will stop playing.

Setting Up the General Options

With the unit in Stop mode, press the MENU button. Press the

¥/

buttons to select SETTINGS, then

press the ENTER button.

Press the

/

buttons to select GENERAL, then press the



or ENTER button.

Press the

/

buttons to select the desired item, then press the



or ENTER button.

Setting Up the Support Options

Support option enable you to check your DVD player information such as the model code, Software

Version, The serial and version numbers can be found on the back side of your DVD-Player.

With the unit in Stop mode, press the MENU button. Press the

¥/

buttons to select SETTINGS, then

press the ENTER button.

Press the

/

buttons to select SUPPORT, then press the



or ENTER button.

Select PRODUCT INFORMATION, then press the



or ENTER button.

Troubleshooting

Reference

Problem Action

5.1 channel sound is not

being reproduced.

(DVD-C550K)

5.1 channel sound is reproduced only •

when the following conditions are met. :

1) The DVD player is connected with the proper Ampliﬁ er

2) The disc is recorded with 5.1 channel sound.

Check whether the disc being played has the "5.1 ch" mark on the outside.•

Check if your audio system is connected and working properly. •

In a SETUP Menu, is the Audio Output set Bitstream?•

The screen is blocked.

Press the •

■

/|| button (in front panel)

for more than 5 seconds under no

disc inside. All setting will revert to factory settings.

Forgot password.

Press the •

■

/|| button (in front panel)

for more than 5 seconds under no

disc inside. All setings including the password will revert to the factory

settings. Don't use this unless absolutely necessary.

No HDMI output

Check the Video output is HDMI enabled.•

Check the connection between the •

TV and the HDMI jack of DVD player.

See if the TV supports this 480p/ 576p/720p/1080i/1080p DVD player.•

Abnormal HDMI output

screen.

If snow noise appears on the screen, it means that TV does not •

support HDCP (High-bandwidth Digital Content Protection).

HDMI output Jitter

Check your TV system setup correctly.•

The screen Jitter phenomenon may occur when frame rate is converted from 50Hz to •

60 Hz for 720p/1080i/ 1080p HDMI (High Deﬁ nition Multimedia Interface) Output.

Please refer to the user's manual of your TV.•

Before requesting service (troubleshooting), please check the following.

Memo

Spesifications

General

Power Requirements

AC110~240V, 50/60Hz

Power Comsumption

Weight

DVD-C500 : 1.2 Kg

DVD-C550/DVD-C550K : 1.5 Kg

Dimensions

DVD-C500 :

360mm(W) X 207mm(D) X 42mm(H)

DVD-C550/DVD-C550K :

430mm(W) X 207mm(D) X 42mm(H)

Operating Temperature Range +5ºC to +35ºC

Operating Humidity Range 10 % to 75 %

Video Output

Composite Video 1 channel : 1.0 Vp-p (75 Ω load)

Component Video

Y : 1.0 Vp-p (75 Ω load)

Pr : 0.70 Vp-p (75 Ω load)

Pb : 0.70 Vp-p (75 Ω load)

HDMI 480p, 576p, 720p, 1080p, 1080i

Audio Output

Output terminal RCA

Maximum Output Level 2Vrms

Frequency Response 20 Hz to 20 kHz

Digital Audio Out Coaxial terminal (S/PDIF)

5.1 Channel (DVD-C550K) F/L, F/R, R/L, R/R, CT, S/W

Memo

$POUBDU4".46/(803-%8*%&

*GZPVIBWFBOZRVFTUJPOTPSDPNNFOUTSFMBUJOHUP4BNTVOHQSPEVDUTQMFBTFDPOUBDUUIF4".46/(DVTUPNFSDBSFDFOUFS

Region Area Contact Center



Web Site

North America

Canada 1-800-SAMSUNG (726-7864) www.samsung.com/ca

Mexico 01-800-SAMSUNG (726-7864) www.samsung.com/mx

U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com/us

Latin America

Argentine 0800-333-3733 www.samsung.com/ar

Brazil 0800-124-421, 4004-0000 www.samsung.com/br

Chile 800-SAMSUNG (726-7864) www.samsung.com/cl

Nicaragua 00-1800-5077267 www.samsung.com/latin

Honduras 800-7919267 www.samsung.com/latin

Costa Rica 0-800-507-7267 www.samsung.com/latin

Ecuador 1-800-10-7267 www.samsung.com/latin

El Salvador 800-6225 www.samsung.com/latin

Guatemala 1-800-299-0013 www.samsung.com/latin

Jamaica 1-800-234-7267 www.samsung.com/latin

Panama 800-7267 www.samsung.com/latin

Puerto Rico 1-800-682-3180 www.samsung.com/latin

Rep. Dominica 1-800-751-2676 www.samsung.com/latin

Trinidad & Tobago 1-800-SAMSUNG (726-7864) www.samsung.com/latin

Venezuela 0-800-100-5303 www.samsung.com/latin

Colombia 01-8000112112 www.samsung.com.co

Europe

Belgium 02 201 2418

www.samsung.com/be (Dutch)

www.samsung.com/be_fr (French)

Czech Republic 800-SAMSUNG (800-726786) www.samsung.com/cz

Denmark 8-SAMSUNG (7267864) www.samsung.com/dk

Finland 30-6227 515 www.samsung.com/ﬁ

France 01 4863 0000 www.samsung.com/fr

Germany 01805-SAMSUNG (726-7864 å 0,14/Min) www.samsung.de

Hungary 06-80-SAMSUNG (726-7864) www.samsung.com/hu

Italia 800-SAMSUNG (726-7864) www.samsung.com/it

Luxemburg 02 261 03 710 www.samsung.com/lu

Netherlands 0900-SAMSUNG (0900-7267864) (å 0,10/Min) www.samsung.com/nl

Norway 3-SAMSUNG (7267864) www.samsung.com/no

Poland 0 801 1SAMSUNG (172678), 022-607-93-33 www.samsung.com/pl

Portugal 80820-SAMSUNG (726-7864) www.samsung.com/pt

Slovakia 0800-SAMSUNG (726-7864) www.samsung.com/sk

Spain 902-1-SAMSUNG (902 172 678) www.samsung.com/es

Sweden 0771 726 7864 (SAMSUNG) www.samsung.com/se

U.K 0845 SAMSUNG (7267864) www.samsung.com/uk

Eire 0818 717 100 www.samsung.com/ie

Austria 0810-SAMSUNG (7267864, å 0.07/min) www.samsung.com/at

Switzerland 0848-SAMSUNG (7267864, CHF 0.08/min)

www.samsung.com/ch

www.samsung.com/ch_fr/ (French)

CIS

Russia 8-800-555-55-55 www.samsung.ru

Kazakhstan 8-10-800-500-55-500 www.samsung.com/kz_ru

Uzbekistan 8-10-800-500-55-500 www.samsung.com/kz_ru

Kyrgyzstan 00-800-500-55-500

Tadjikistan 8-10-800-500-55-500

Ukraine 8-800-502-0000

www.samsung.ua

www.samsung.com/ua_ru

Belarus 810-800-500-55-500

Moldova 00-800-500-55-500

Lithuania 8-800-77777 www.samsung.com/lt

Latvia 8000-7267 www.samsung.com/lv

Estonia 800-7267 www.samsung.com/ee

Asia Paciﬁc

Australia 1300 362 603 www.samsung.com/au

New Zealand 0800 SAMSUNG (0800 726 786) www.samsung.com/nz

China 400-810-5858, 010-6475 1880 www.samsung.com/cn

Hong Kong 3698-4698

www.samsung.com/hk

www.samsung.com/hk_en/

India 3030 8282, 1800 110011, 1800 3000 8282 www.samsung.com/in

Indonesia 0800-112-8888 www.samsung.com/id

Japan 0120-327-527 www.samsung.com/jp

Malaysia 1800-88-9999 www.samsung.com/my

Philippines

1-800-10-SAMSUNG (726-7864), 1-800-3-SAMSUNG (726-7864),

1-800-8-SAMSUNG (726-7864), 02-5805777

www.samsung.com/ph

Singapore 1800-SAMSUNG (726-7864) www.samsung.com/sg

Thailand 1800-29-3232, 02-689-3232 www.samsung.com/th

Taiwan 0800-329-999 www.samsung.com/tw

Vietnam 1 800 588 889 www.samsung.com/vn

Middle East &

Africa

Turkey 444 77 11 www.samsung.com/tr

South Africa 0860-SAMSUNG (726-7864 ) www.samsung.com/za

U.A.E 800-SAMSUNG (726-7864), 8000-4726 www.samsung.com/ae

FRANÇAIS

Lecteur DVD

Manuel d'utilisation

Un monde de possibilités

Merci d’avoir choisi Samsung.

Pour bénéﬁ cier d’un service plus complet,

enregistrez votre produit sur le site

www.samsung.com/global/register

DVD-C500

DVD-C550

DVD-C550K

Précautions

1. Installation

Assurez-vous que l’alimentation secteur de votre

domicile corresponde bien à celle indiquée sur la plaque

d’identification apposée au dos de votre appareil.

Installez celui-ci sur un support adapté plat, en lui

ménageant suffisamment d’espace libre pour une bonne

ventilation (7 à 10 cm). Assurez-vous que les fentes

de ventilation ne soient pas recouvertes. Ne placez

pas d’autres appareils ni des appareils lourds sur votre

lecteur DVD. Ne le placez pas sur des amplificateurs

ou sur tout autre équipement pouvant dégager de la

chaleur. Avant de déplacer le lecteur, assurez-vous que

le tiroir à disque est vide.Ce lecteur DVD est conçu

pour un usage continu. Laisser l’appareil en mode

veille n’interrompt pas son alimentation électrique. Pour

déconnecter complètement le lecteur du secteur, il doit

être débranché de sa prise murale, ce qui est conseillé

si vous ne l’utilisez pas pendant un certain temps. La

prise d’alimentation fait office de système de déconnex-

ion; elle doit donc rester disponible en permanence.

2. Pour votre sécurité

N’ouvrez jamais l’appareil et ne démontez aucun de ses

éléments. Cela peut être dangereux pour vous et pour

certaines pièces fragiles. Vous risquez de recevoir une

décharge électrique ou d’entrer en contact avec le rayon

laser. N’essayez pas de regarder à l’intérieur de l’appareil,

ni par l’ouverture du tiroir, ni par toute autre fente.

3. Attention

Protégez le lecteur de l’humidité et de la chaleur exces-

sive, ainsi que de tout équipement créant de puissants

champs magnétiques ou électriques (haut-parleurs).

Veillez à éviter toute projection sur i’appareil et ne

placez jamais de récipients contenant un liquide (ex. :

vase) dessus. Déconnectez le câble d’alimentation du

secteur si le lecteur fonctionne mal. Votre lecteur n’est

pas conçu pour une utilisation dans un but industriel ni

commercial, mais pour une utilisation familiale. L’usage

de ce produit est destiné à des fins purement privées.

Copier ou télécharger des fichiers musicaux à des fins

de commercialisation ou pour tout autre but lucratif

constitue ou pourrait constituer une violation du code

de la propriété Intellectuelle. exclusion de garantie :

dans la mesure permise par la loi, toute déclaration ou

toute contrefaçon de droits d’auteurs ou de tous autres

droits de propriété intellectuelle résultant de l’utilisation

du produit dans des conditions autres que celles visées

ci-dessus est exclue. Condensation : Si votre appareil

et/ou un disque a passé un certain temps dans une

température ambiante froide, par ex. pendant un trans-

port en hiver, attendez environ 2 heures qu’il ait atteint

la température ambiante afin d’éviter de l'endommager.

4. Disques

Manipulez vos disques avec précaution. Prenez les

disques avec les doigts sur le bord ou sur l'ouverture.

Placez toujours le disque avec l'étiquette vers le haut

(dans le cas d'un disque à une seule face). Utilisez

toujours un chiffon souple pour nettoyer le disque si

nécessaire, et essuyez du centre vers le bord. Placez

toujours les disques dans leur emballage après leur

lecture et conservez-les en position verticale. Placez

toujours le disque correctement dans son logement.

N'utilisez jamais d'atomiseurs de nettoyage, benzine,

liquides à électricité statique ou d'autres types de sol-

vants si la surface du disque est sale. Essuyez délicate-

ment avec un chiffon souple et humide (uniquement de

l'eau), n'essuyez jamais le disque avec un mouvement

circulaire car les rayures circulaires peuvent facilement

marquer et provoquer des parasites pendant la lecture.

5. Piles

Les piles utilisées dans cet appareil contiennent des

produits chimiques nuisibles à l'environnement. Ne

jetez pas les piles avec les déchets domestiques. Nous

recommandons de les déposer dans un lieu pouvant

accepter ce type de déche.

L’unité qui se trouve avec ce manuel de l’utilisateur est

fournie sous licence sous certains droits de propriété

intellectuelle de parties tierces. Cette licence est limitée

à une utilisation privée non commerciale par l’utilisateur

final pour les contenus sous licence. Aucun droit n’est

concédé pour une utilisation commerciale. Cette licence

ne couvre aucun produit autre que celui-ci et ne peut

être étendue à un produit ou processus qui n’est pas

sous licence selon la norme ISO/IEC 11172-3 ou ISO/

IEC 13818-3 utilisé ou vendu avec ce produit. La

licence couvre uniquement l’utilisation de ce produit

pour encoder et/ou décoder des fichiers audio selon

la norme ISO/IEC 11172-3 ou ISO/IEC 13818-3. Aucun

droit n’est cédé sous cette licence pour des caractéris-

tiques ou des fonctions du produit qui ne sont pas

conformes à la norme ISO/IEC 11172-3 ou ISO/

IEC 13818-3.

Attention : Les contrôles, les ajustements ou les

procédures autres que ceux spécifiés dans ce manuel

peuvent provoquer une explosion avec émission de

radiations dangereuses.

Table des matières

Précautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Configuration

Caractéristiques des disques . . . . . . . . . . . . . . . 2

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Télécommande . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Branchements

Choix de la connexion . . . . . . . . . . . . . . . . . . . . 4

Fonctions Élémentaires

Lecture des disques . . . . . . . . . . . . . . . . . . . . . . 5

Recherche et saut de chapitre ou de plage . . . . 5

Utilisation de la fonction d’affichage . . . . . . . . . . 6

Utilisation du menu Disque et du menu Titres . . 6

Lecture répétée . . . . . . . . . . . . . . . . . . . . . . . . . 6

Lecture lente . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Fonctions Avancées

Réglage du rapport d’aspect hauteur-largeur de

l’écran (EZ View) . . . . . . . . . . . . . . . . . . . . . . . . . 6

Sélection de la langue d’écoute . . . . . . . . . . . . . 7

Sélection de la langue des sous-titres . . . . . . . . 7

Sélection de l’angle de prise de vue à l’écran . . 7

Utilisation des repères . . . . . . . . . . . . . . . . . . . . . 7

Utilisation des fonctions avancées . . . . . . . . . . . 7

Menu Clips pour

MP3/WMA/JPEG/MPEG4/

CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Modifier un Dossier . . . . . . . . . . . . . . . . . . . . . . . 7

Lecture de MP3/WMA/CD Audio . . . . . . . . . . . . . 7

Lecture de MPEG4 . . . . . . . . . . . . . . . . . . . . . . . 8

Lecture de fichiers multimédia avec la

fonctionnalité USB Host (Hôte USB)

(Seulement DVD-C550/DVD-C550K) . . . . . . . . . 9

Extraction audio (Seulement DVD-C550/

DVD-C550K) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Lecture de CD image . . . . . . . . . . . . . . . . . . . . . 9

Lecture de CD image pour JPEG HD . . . . . . . . 10

Fonctions karaoké

(Seulement DVD-C550K)

Fonctions karaoké . . . . . . . . . . . . . . . . . . . . . . 10

Changement du Menu

Configuration

Utilisation du menu de configuration . . . . . . . . . 10

Configuration des options d’affichage . . . . . . . . 10

Configuration des options audio . . . . . . . . . . . . 11

Configuration des options système . . . . . . . . . . 12

Configuration des options de langue. . . . . . . . . 12

Configuration des options de sécurité . . . . . . . . 12

Configuration des options générales . . . . . . . . . . 13

Configuration des options d’assistance . . . . . . . . 13

Fiche Technique

Problèmes et solutions . . . . . . . . . . . . . . . . . . . 13

Spécifications . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Excellente qualité sonore

Le système Dolby Digital mis au point par Dolby Laboratories,

vous garantit une reproduction sonore de haute qualité.

Format écran

Vous permettant de choisir entre le format écran normal (4/3)

ou bien le format grand écran (16/9).

Ralenti variable

Vous pouvez visionner une séquence importante en faisant

varier la vitesse du ralenti.

Lecture 1080p

Ce lecture adapte les DVD standard à la lecture sur des

téléviseur 1080p,

Contrôle parental (DVD)

Le contrôle parental permet aux utilisateurs de fixer le seuil au-

delà duquel ils interdisent à leurs enfants de regarder des films

de violence ou réservés aux adu.

Fonctions variées du menu affiché

Vous pouvez sélectionner la langue d’écoute et des sous-titres, ainsi

que l’angle de vue que vous préférez pendant la lecture.

Balayage progressif

Le balayage progressif améliore l’image en doublant le nom-

bre de lignes de balayage associé à l’affichage classique par

balayage entrelacé.

EZ VIEW (Visionnement facile) (DVD

)

La fonction Easy View permet de régler l’image en fonction

Caractéristiques des disques

Conﬁ guration

du format de votre écran de télévision (16/9 ou 4/3).

Digital Photo Viewer (JPEG) (vision-

neur de photos numériques)

Grâce à ce visionneur, vous pouvez voir des images numéri-

ques sur votre téléviseur.

Répétition

Vous pouvez écouter une chanson ou visionner un film plusieurs fois

par une simple pression sur la touche REPEAT.

MP3/WMA

Cet appareil peut lire des disques gravés à partir de fichiers

MP3/WMA.

MPEG4

Cet appareil peut lire les fichiers avi enregistrés au format

MPEG-4.

HDMI (High Definition Multimedia

Interface)

HDMI diminue le bruit d’image en permettant un

cheminement pur du signal vidéo/audio numérique

entre le lecteur et votre TV.

Extraction audio (Seulement

DVD-C550/DVD-C550K)

Cette fonction permet de copier les fichiers audio d’un

CD sur un périphérique USB au format MP3. (CD audio

uniquement – CD DA))

Remarque

- Disques ne pouvant être lus avec ce lecteur.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

•

CDG en lecture audio uniquement (pas d’images).

- La capacité de lecture peut dépendre des

conditions d’enregistrement.

• DVD-R, +R

• CD-RW

• DVD+RW, DVD-RW (mode vidéo)

- Ce lecteur peut ne pas lire certains CD-R,

CD-RW et DVD-R en raison du type de

disque ou des conditions d’enregistrement.

PROTECTION CONTRE LA COPIE

Nombreux sont les disques DVD protéges contre la copie.

Ainsi vous ne pouvez connecter votre lecteur DVD que

directement à la télévision et non au magnétoscope. Si vous

le connectez à un magnétoscope, vous n’obtiendrez que

des images déformées par le système de protection Rovi

Corporation.

Ce lecteur DVD intègre des technologies destinées à

respecter la propriété intellectuelle dont les droits sont proté-

gés par des brevets américains et des procédés de contrôle

de la propriété de Rovi Corporation et d’autres compagnies.

L’utilisation de cette technologie doit être autorisée par Rovi

Corporation. Elle est limitée à l’usage domestique ou aux

utilisations strictement définies par Rovi Corporation. Les

modifications techniques ou le démontage sont interdits

SORTIES DE PROGRESSIVE SCAN

(576p, 720p, 1080p)

“LES CONSOMMATEURS DOIVENT NOTER QUE TOUS

LES TÉLÉVISEURS À HAUT DÉFINITION NE SONT PAS

TOTALEMENT COMPATIBLES AVEC CET APPAREIL ET

QU’UNE ERREUR PEUT SURVENIR SUR L’IMAGE AVEC

LE MODE 576, 720 OU 1080 BALAYAGE PROGRESSIF. IL

EST RECOMMANDÉ À L’UTILISATEUR DE BASCULER LE

MODE VERS ‘DÉFINITION STANDARD’. SI VOUS AVEZ

DES QUESTIONS CONCERNANT LA COMPATIBILITÉ DES

MODÈLES 576P, 720P ET 1080P DE NOTRE LECTEUR

DVD, VEUILLEZ CONTACTER NOTRE CENTRE DE

SAMSUNG SERVICE CONSOMMATEURS.”

Description

Face avant

Code régional de lecture

Le lecteur DVD et les disques sont codés dif-

féremment selon les parties du monde. Il faut

donc le code correspondant à chaque région pour

un bon fonctionnement du lecteur. Si vous tentez

de lire un disque DVD avec un code incorrect,

le lecteur ne fonctionnera pas et un message

d’erreur apparaîtra.

Les codes régionaux pour ce lecteur figurent sur

la face arrière du lecteur.

DivX Certification

DivX, DivX Certified et les

logos qui leur sont associés

sont des marques déposées de DivX Networks,

Inc. et font l’objet d’une licence.

“DivX certifié pour lire des vidéos DivX, y compris

les contenus exclusifs.”

Notation sur le dsque

Code régional de lecture

Système de diffusion adopté au Roy-

aume Uni, France, Allemagne, etc

Disque Dolby numérique

Disque stéréo

Disque audio numérique

Disque DTS

Disque encodé en MP3

DIGITAL

SOUND

STEREO

PAL

Télécommande

1. Tiroir à disque

Permet de charger un disque.

2. Afficheur

lI contient tous les indicateurs de fonctionnement.

3. Touche OPEN/CLOSE ( )

Pour ouvrir ou fermer le tiroir à disque.

4. Touche STOP ( )

Pour arrêter la lecture du disque.

5. LECTURE/PAUSE ( )

Permet de lancer la lecture d’un disque ou de la

mettre en pause.

6. POWER ON/OFF ( )

Si vous activez/désactivez ceci, le lecteur sera

respectivement activé/désactivé.

7. Hôte USB (Seulement

DVD-C550/DVD-C550K)

Permet de brancher un appareil photo numérique,

un lecteur MP3, une carte mémoire Memory Stick,

un lecteur de carte ou tout autre support de stock-

age amovible.

8. MICROPHONE VOLUME

(VOLUME DU MICRO)

(Seulement DVD-C550K)

Permet de régler le volume du micro. Appuyez sur

le bouton. Tournez-le vers la gauche ou vers la

droite pour régler le volume.

9. MIC 1/2

(Seulement DVD-C550K)

Branchez le micro pour pouvoir utiliser les fonc-

tions karaoké.

DVD-C500

DVD-C550K

DVD-C550

DVD-C500

DVD-C550

DVD-C550K

Choix de la connexion

Branchements

Cette page présente quelques exemples de connexions généralement utilisées pour raccorder le lecteur

DVD au téléviseur ou à d’autres appareils.

Avant de connecter le lecteur DVD

- Avant de connecter ou de déconnecter les câbles, assurez-vous que le lecteur DVD, le téléviseur et

les autres appareils sont bien débranchés de la prise secteur.

- Pour obtenir des informations supplé mentaires relatives aux éléments ajoutés (un téléviseur, par

exemple), reportez-

vous aux modes d’emploi de ces éléments.

A. Raccordement à un téléviseur (CVBS Video)

1. A l’aide des câbles vidéo/audio, raccordez les sorties VIDEO (jaune)/AUDIO (rouge et blanche) OUT

ou 5.1 (rouge et blanche) (avant G-D) située sur le panneau arrière du lecteur DVD aux entrées VIDEO

(jaune)/AUDIO (rouge et blanche) IN de votre téléviseur.

2. Allumez le lecteur DVD et le téléviseur.

3. Appuyez sur le sélecteur d’entrée de la télécommande de votre téléviseur jusqu’à ce que le signal vidéo du

lecteur DVD apparaisse à l’écran.

Remarque

- Un bruit peut se faire entendre si le câble audio est trop proche du cordon d’alimentation.

Si vous souhaitez relier l’appareil à un amplificateur, reportez-vous à la rubrique Raccordement d’un amplificateur.

Le nombre et l’implantation des prises peuvent varier en fonction de votre téléviseur. Veuillez vous

reporter au manuel d’utilisation de celui-ci pour plus de détails.

Si votre téléviseur est équipé d’une entrée audio, raccordez-la à la sortie [AUDIO OUT] (prise blanche de

gauche) du lecteur DVD.

Si vous appuyez plusieurs fois sur le bouton VIDEO SEL. lorsque le lecteur ne lit aucun disque ou

qu’aucun disque n’est inséré, les options du mode Sortie vidéo s’affichent dans l’ordre suivant :

(I-SCAN ➝ P-SCAN)

Raccordement à un téléviseur (affichage entrelacé/ balayage progressif)

1. À l’aide de câbles de composant vidéo, raccordez les prises COMPONENT VIDEO OUT situées à l’arrière

du lecteur DVD aux prises COMPONENT IN de votre téléviseur.

A l’aide des câbles audio, raccordez les sorties AUDIO OUT (rouge et blanche) ou 5.1 (rouge et blanche)

(avant G-D) située sur le panneau arrière du lecteur DVD aux entrées AUDIO IN (rouge et blanche) de votre

téléviseur. Allumez le lecteur DVD et le téléviseur.

3. Appuyez sur le sélecteur d’entrée de la télécommande de votre téléviseur jusqu’à ce que le signal de com-

posant du lecteur DVD apparaisse à l’écran.

Réglez la sortie Video Out sur I-SCAN/P-SCAN dans le menu Configuration de l’affichage. Vous pouvez utiliser la

touche VIDEO SEL. pour changer le mode de ”Video Output (sortie vidéo)”.

Remarque

- Qu’est-ce que le balayage progressif ?

Le balayage progressif se caractérise par deux fois plus de lignes que le mode de balayage entrelacé.

Le mode Balayage progressif offre une meilleure qualité d’image.

C. Connexion à un téléviseur (prise DVI/HDMI)

1. À l’aide d’un câble HDMI-DVI/HDMI-HDMI, raccordez la prise HDMI OUT située à l’arrière du lecteur DVD à

la prise DVI/HDMI IN de votre téléviseur.

Si votre téléviseur est équipe de la prise DVI, à l’aide des câbles audio, raccordez les sorties AUDIO OUT

(rouge et blanche) ou 5.1 (rouge et blanche) (avant G-D) située sur le panneau arrière du lecteur DVD aux

entrées AUDIO IN (rouge et blanche) de votre téléviseur. Allumez le lecteur DVD et le téléviseur.

3. Appuyez sur le sélecteur d’entrée de la télécommande de votre téléviseur jusqu’à ce que le signal DVI/

HDMI du lecteur DVD apparaisse à l’écran.

Spécifications Vidéo HDMI

Lorsque vous appuyez plusieurs fois sur le bouton HDMI SEL., la résolution change dans l’ordre suivant :

480p/576p, 720p, 1080i et 1080p

Le premier appui sur le touche HDMI SEL. permet d’afficher la résolution actuelle.

Le deuxième appui sur le touche HDMI SEL.

permet de modifier la résolution de sortie HDMI.

- Il se peut que certaines résolutions de sortie HDMI ne soient pas disponibles sur votre TV.

Référez-vous au manuel de l’utilisateur de votre TV.

- Si un câble HDMI ou HDMI-DVI est branché sur le téléviseur, la sortie du lecteur DVD bascule

automatiquement sur HDMI/DVI au bout de 10 secondes.

Si vous réglez la résolution de sortie HDMI 720p, 1080i ou 1080p, la sortie HDMI offre une meilleure qualité d’image.

- Si vous reliez le câble HDMI au téléviseur Samsung, vous pouvez facilement régler le lecteur DVD à

l’aide de la télécommande du téléviseur (uniquement disponible sur les téléviseur Samsung prenant

en charge la fonction Anynet+(HDMI-CEC)

- Vérifiez que le logo se trouve sur le téléviseur (si votre téléviseur comporte le logo ,

c’est qu’il prend en charge la fonction Anynet+.

•

HDMI (High Definition Multimedia Interface)

HDMI est une interface qui permet une transmission numérique des données vidéo et audio par

un seul connecteur. En utilisant HDMI, le lecteur DVD transmet un signal vidéo et audio numérique

et affiche une image vive sur un téléviseur muni d’une prise HDMI.

• Description de la connexion HDMI

Connecteur HDMI – les données vidéos non compressées et les données audio numériques (don-

nées LPCM par trames).

- Bien que le lecteur utilise un câble HDMI, il n’émet qu’un signal numérique pur vers la TV.

Si la TV ne supporte pas HDCP (High-bandwidth Digital content protection), le bruit d’écran apparaît à l’écran.

• Pourquoi Samsung utilise HDMI?

Les TV analogiques nécessitent un signal vidéo/audio analogique. Cependant, les données transmises à la TV lors

de la lecture d’un DVD sont numériques. De ce fait, un convertisseur numérique vers analogique (sur le lecteur

dvd) ou un convertisseur analogique vers numérique (sur la TV) est nécessaire. Pendant cette conversion, la

qualité d’image se dégrade à cause du bruit ou de la perte du signal. DVI est une technologie plus avancée car elle

ne nécessite aucune conversion N/A : c’est un signal numérique pur depuis le lecteur jusqu’à votre TV.

• Qu’est-ce HDCP?

HDCP (High-bandwidth Digital Content Protection) est un système de protection contre la copie du contenu du

DVD émis par DVI/HDMI. Il fournit un lien numérique sécurisé entre la source (PC, DVD, etc.) et le dispositif

d’affichage (TV, projecteur, etc.). Le contenu est encrypté sur le dispositif source afin d’empêcher des copies non

autorisées.

1. Touche DVD POWER

Pour mettre l’appareil sous tension ou hors

tension.

2 Touche DVD

Lorsque vous utilisez un lecteur DVD.

3. Touche TV

Pour faire fonctionner votre téléviseur Samsung.

4. Touche EZ VIEW

Le format d’image peut facilement être

adapté au format de votre écran de télévi-

sion (16/9 ou 4/3).

Touche MARKER

6. Touche REPEAT

Pour répéter un titre ou tous les titres.

7. Touche DISC MENU

Affiche le menu disque.

8. Touche INFO

Vous pouvez également accéder à la fonction

d’affichage.

9. Touches TV VOL (+, -)

Réglage du volume.

10. Touches SKIP (

)

Utilisez pour sauter un titre, chapitre ou piste.

11. Touche STOP (■)

12. Touche MENU

Pour afficher le menu des réglages du lecteur DVD.

13.

Touche ENTER/

¥

Déplacez la touche ENTER vers le haut/bas ou

vers la gauche/droite pour choisir des options de

menus.

14. Touche TOOLS

Pour afficher le mode du disque courant.

Permet d’afficher la bannière concernant les infor-

mations de lecture.

15. Touche OPEN/CLOSE ( )

Pour ouvrir et fermer le tiroir à disque.

16. Touche HDMI SEL.

Réglage de la résolution de sortie HDMI.

17. Touche USB (Seulement

DVD-C550/DVD-C550K)

Touche ZOOM

(Seulement DVD-C500)

Permet d’agrandir l’image DVD.

18. Touche VIDEO SEL.

Changement du mode Video output (Sortie vidéo).

19.

Touche REPEAT A-B

Permet de répeter la lecture d’un disque d’un

instant A à un instant B.

20.

Touche SUBTITLE

21.

Touche TITLE MENU

Affiche le menu de titre.

22. Touche AUDIO/TV SOURCE

Appuyez sur cette touche pour modifier les

options audio. Utilisezce bouton pour sélec-

tionner une source TV disponible (mode TV).

23. Touche PAUSE (

∏∏

)

Pour suspendre la lecture.

24. Touches SEARCH (

)

Permet une recherche avant ou arrière.

25. Touches TV CH (

P, Q

)

Permet de sélectionner le canal.

26. Touche PLAY (



)

Pour commencer la lecture.

27 Touche RETURN

Pour revenir au menu précédent.

28. Touche EXIT

Permet de quitter le menu affiche à l’écran.

29.

Touche KARAOKÉ (



)

(Seulement DVD-C550K)

Permet d’activer les fonctions karaoké.

La page est en cours de chargement...

Samsung DVD-C550 Manuel utilisateur

Marque: Samsung

Modèle: DVD-C550

Catégorie: Lecteurs DVD

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Samsung DVD-C550 User manual

Samsung DVD-C550 Manuel utilisateur

Samsung DVD-C550 Manuel utilisateur

dans d''autres langues

Documents connexes