LG WD-13514BDM Le manuel du propriétaire

LG
Marque
LG
Modèle
WD-13514BDM
Catégorie
Machines à laver
Taper
Le manuel du propriétaire

Ce manuel convient également à

P/No.: 3828ER3054H
WM2688H*M
Designed specially to use only
HE (High Efficiency) detergent
PRODUCT FEATURES
2
CONTENTS
Ultra Capacity
The Larger drum enables not just higher head drop and stronger centrifugal force, but also
less tangling and wrinkling of the laundry. Heavier loads, such as king size comforters,
blankets, and curtains, can be washed.
Direct Drive System
The advanced Brushless DC motor directly drives the drum without
belt and pulley.
Tilted Drum and Extra Large Door Opening
Tilted drum and extra large opening make it possible to load
and unload clothing more easily.
Steam Washing and SteamFresh
TM
Steam Washing features upgraded washing performance with low energy and water
consumption. SteamFresh
TM
cycle removes wrinkles from dry clothes.
RollerJets
Washing ball enhances the wash performance and reduces damage
to the clothing. The jets spray and help tumble clothes to enhance
washing performance while maintaining fabric care.
Automatic Wash Load Detection
Automatically detects the load and optimizes the washing time.
Built-in Heater
Internal heater helps to maintain water temperature at its optimum level for selected cycles.
Child Lock
The Child lock prevents children from pressing any button to change the settings during
operation.
Using the RLM (Remote Laundry Monitor)
The RLM monitors status of your washer and/or dryer. You can plug the display unit into any
power outlet in your home.
The RLM Display Unit can be purchased separately for this washer.
Important Safety Information ...........................................................................................................................................3
Specifications...................................................................................................................................................................4
Installation Instructions ....................................................................................................................................................5
Preparation Before Washing..........................................................................................................................................10
Using the Dispenser ......................................................................................................................................................11
Cycles ...........................................................................................................................................................................13
How to Use the Washer.................................................................................................................................................14
Maintenance ..................................................................................................................................................................17
Troubleshooting Guide ..................................................................................................................................................20
Warranty ........................................................................................................................................................................23
󲷸 󲷸
󲷸 󲷸
IMPORTANT SAFETY INFORMATION
ENGLISH
3
READ ALL INSTRUCTIONS BEFORE USE
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire or
explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
IIMMPPOORRTTAANNTT SSAAFFEETTYY IINNSSTTRRUUCCTTIIOONNSS
• Read all instructions before using the washer.
• Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry cleaning solvents, or other
flammable or explosive substances, as they give
off vapors that could ignite or explode.
• Do not add gasoline, dry cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
• Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the
water flow from each for several minutes. This will
release any accumulated hydrogen gas. As the gas
is flammable, do not smoke or use an open flame
during this time.
• Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children.
• Before the washer is removed from service or
discarded, remove the door to prevent children
from hiding inside.
• Do not install or store the washer where it will be
exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the washer or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or published user-repair instructions
that you understand and have the skills to carry
out.
• See Installation Instructions for grounding
requirements.
• ALWAYS follow the fabric care instructions
supplied by the garment manufacturer.
• Do not place items exposed to cooking oil in your
washer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause
a load to catch fire.
• Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
WARNING
: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic
precautions, including the following:
SSAAVVEE TTHHEESSEE IINNSSTTRRUUCCTTIIOONNSS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
• Do not use an adapter or extension cord.
• Do not remove ground prong.
• If you don’t have the proper outlet, consult an electrician.
GROUNDING INSTRUCTIONS
WARNING
: Improper connection of the equipment-grounding conductor can result in risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet,
have a proper outlet installed by a qualified electrician.
!
!
!
for removing shipping bolts
and leveling the washer
& Steam Nozzle
Drum Light
Door Seal
H
I
G
H
WASHING
H
I
G
H
H
O
T
/
C
O
L
D
S
T
E
A
M
D
O
O
R
L
O
C
K
EST. TI
ME:
RE
MANING
5%
N
O
R
M
A
L
C
H
I
L
D
L
O
C
K
D
E
L
A
Y
W
A
S
H
1:21
SPECIFICATIONS
4
Accessories
Name: Front-loading Washing Machine
Power supply: 120V~ 60Hz
Size: 68.6 cm (W) X 75.6 cm (D) X 98.3 cm (H), 129.1 cm (D with door open)
27”(W) X 29
3
/
4
”(D) X 38
11
/
16
”(H), 50
13
/
16
”(D with door open)
Weight: 192 lbs. (87 kg)
Spin speed: 1320 rpm max.
Permissible water pressure: 14.5 ~ 116 PSI (100 ~ 800 kPa)
󳀌
Specifications subject to change by manufacturer.
Safety Cover (PLC Modem)
5
INSTALLATION INSTRUCTIONS
1. To prevent internal damage during transport,
4 locking bolts are installed. Before operating
the washer, remove the bolts and braces.
• If they are not removed, it may cause severe
vibration, noise, and malfunction.
3. Take out the 4 bolts and braces by twisting
the braces slightly. Keep the 4 bolts, braces
and the wrench for future use.
• Whenever the appliance is transported, the
shipping bolts and braces must be reinstalled.
2. Unscrew the 4 bolts with the wrench supplied.
Do first lower side to remove easily. One of the
bolts retains the power cord of the washer to
prevent operating without removing bolts.
4. Close the holes with the caps supplied.
The appliance is fitted with shipping bolts to prevent
internal damage during transportation.
Packing and all shipping bolts must be removed
before using the washer.
󳀙 When unpacking the base, be sure to remove
the additional packing support in the middle of
the base packing.
: Two or more people may be need to install and move the appliance.
Shipping bolts
Install or store unit where it will not be exposed to temperatures below freezing or
exposed to outside weather conditions.
Properly ground washer to conform with all governing codes and ordinances.
To reduce the risk of electric shock, do not install the washer in humid spaces.
The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
In countries where there are areas which may be subject to infestation by cockroaches or other vermin, pay
particular attention to keeping the appliance and its surroundings in clean condition at all times.
Damage caused by cockroaches or other vermin will not be covered by the appliance warranty.
Removing shipping bolts
cap
ENGLISH
!
WARNING
INSTALLATION INSTRUCTIONS
6
Installation clearances
The location must be large enough to fully open
the washer door.
Washer dimensions
• Most installations require a minimum 4 in.
(10 cm) clearance behind the washer.
Minimum installation spacing for
recessed area installation.
The following dimensions shown are for the minimum
spacing allowed.
Additional spacing should be considered for
installation and servicing.
• Additional clearances might be required for wall,
door and floor moldings.
• Additional spacing of 1 in. (2.5 cm) on all sides of
the washer is recommended to reduce noise
transfer.
Companion appliance spacing should also be
considered.
Level floor
• Allowable slope under entire washer is 1°.
• To minimize noise and vibration, the washer
MUST be installed on a solidly constructed
floor.
• Carpeting and soft tile surfaces are not
recommended.
• Never install the washer on a platform or weakly
supported structure.
NOTE: A firm, solid floor is even more critical to a
front-loading washer than to a top-loader.
If your floor is wood and/or frame
construction, you may need to reinforce it.
Front-loaders use substantially faster spin
speeds than top-loaders, causing greater
vibration. If the floor is not solid, your washer
will vibrate. You will hear and feel the
vibration throughout your house.
Power outlet
•
Must be within 60 in. (1.5 m) of either side of the
washer. Do not overload the outlet with more
than one appliance.
• Time-delay fuse or circuit breaker is recommended.
NOTE: It is the personal responsibility and obligation
of the customer to have a proper outlet
installed by a qualified electrician.
[Front view]
[Side view]
H
I
GH
WASHING
H
I
G
H
H
O
T
/
C
O
L
D
ST
E
A
M
D
O
O
R
L
O
CK
E
S
T
.
T
I
M
E
:
R
E
M
A
N
I
N
G
5
%
NO
RM
A
L
C
H
I
L
D
LO
C
K
D
EL
A
Y
W
A
S
H
1
:
2
1
INSTALLATION INSTRUCTIONS
ENGLISH
7
• Water supply pressure must be between
14.5 and 116 psi(100~800 kPa).
• Do not crossthread when connecting inlet hose to the
valve.
• If the water supply pressure is more than 116 psi,
a pressure reducing device should be installed.
• Two Sealing washers are supplied with the water inlet
hoses to prevent water leaks.
• Check for leakage of washing machine connections by
turning the tap completely on.
• Periodically check the condition of the hose and replace
the hose if necessary.
• Make sure that there is no kink in the hose and that it is
not crushed.
• Be sure that the two water input ports are connected to
the correct water faucets. The connector for hot water is
colored red.
• Use ONLY the inlet hoses provided by LG with this
laundry product. Aftermarket hoses are not guaranteed to
fit or function correctly. Other hoses may not tighten
correctly and could cause leaks. Subsequent damage to
product or property will not be covered under the terms of
LG's warranty.
Connecting water supply hose
NOTE: Washing Machine is to be connected to the water mains using new hoses.
Old hoses should not be used.
Electrical connection
• Do not use an extension cord or double adapter.
• If the supply cord is damaged, it must be replaced by a qualified person in order to avoid a hazard.
• If the machine will not be used for an extended time, unplug it and shut off the water supply.
• Connect the machine to a grounded outlet in accordance with current wiring regulations.
• The appliance must be positioned so that the plug is easily accessible.
Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center.
Do not install your washing machine in a room where temperatures below freezing may occur.
Frozen hoses may burst under pressure. The reliability of the electronic control unit may be impaired
at temperatures below the freezing point.
If the appliance is delivered in the winter months and temperatures are below freezing,
store the washing machine at room temperature for a few hours before putting it into operation.
!
CAUTION! Concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be
certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords,
or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
INSTALLATION INSTRUCTIONS
8
Installation of drain hose
HIGH
WASHING
HIGHHOT/
COLD
STEAM
DOOR LOCK
EST. TIME:
REMANING
5%
NORMAL
CHILD LOCK DELAY WASH
1:21
HIGH
WASHING
HIGHHOT/
COLD
STEAM
DOOR LOCK
EST. TIME:
REMANING
5%
NORMAL
CHILD LOCK DELAY WASH
1:21
H
I
G
H
W
A
S
H
IN
G
H
IG
HH
O
T
/
C
O
L
D
S
T
E
A
M
D
O
O
R
L
O
C
K
E
S
T
.
T
IM
E
:
R
E
M
A
N
I
N
G
5
%
N
O
R
M
A
L
C
H
I
L
D
L
O
C
K
D
E
L
A
Y
W
A
S
H
1:21
• The drain hose should not be placed higher than
96 in. from the bottom of the washer.
• Properly securing the drain hose will protect the
floor from damage due to water leakage.
• Place the end of the drain hose in the hole of the
floor drain system.
• When installing the drain hose at a sink, secure it
so it cannot break away and cause flooding and
damage.
• Properly securing the drain hose will protect the
floor from damage due to water leakage.
This equipment is not designed for maritime use or for mobile installations such as in RV’s, aircraft, etc.
Turn off the faucet if the machine is to be left for an extended period of time (e.g. holiday).
When disposing of the appliance, cut off the power cable, and destroy the plug.
Disable the door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of suffocation! Keep all
packaging from children.
INSTALLATION INSTRUCTIONS
ENGLISH
9
Level adjustment
• Leveling the washing machine properly prevents
excessive noise and vibration.
Install the appliance on a solid and level floor surface,
preferably in a corner of the room.
• If the floor is uneven, adjust the adjustable feet as
required. (Do not insert pieces of wood, etc. under the
feet.)
NOTE: Extend the feet no more than necessary to level
the washer. The more the feet are extended, the
more the washer will vibrate.
• Make sure that all four feet are stable and resting on
the floor and then check that the appliance is perfectly
level (Use a level).
• After the washer is level, tighten the lock nuts up
against of the base of the washer. All lock nuts must
be tightened.
• It is critical to adjust the feet perfectly. This must be
done while the washer is spinning with a load. Use the
wrench (supplied) to adjust the feet until there is no
vibration. Then tighten the lock nuts to prevent further
adjustment.
NOTE: If there are vibration and noise during the spin
cycle, re-check the leveling of the washer, adjust
the feet as required, and tighten the lock nuts
securely to prevent changes in adjustment.
Run the washer with a test load to make certain
your washer is properly leveled. Put
approximately 6 pounds of laundry in the
machine. Then, press POWER, RINSE+SPIN, and
START/PAUSE, in that order. When the machine
spins at high speed, verify that it is stable. If not,
adjust the feet accordingly.
• If you install the washer and dryer with pedestals, it is
necessary to level with the pedestal feet.
󳀌 Diagonal Check
When pushing down the edges of the washing machine
top plate diagonally, the machine should not move up
and down at all. (Please, check both directions.)
If the machine rocks when pushing the machine top plate
diagonally, adjust the feet again.
H
IGH
WASHING
H
I
G
H
H
O
T
/
C
OLD
S
T
EAM
D
OOR
L
O
C
K
E
ST
.
T
IM
E
:
R
E
M
A
N
I
N
G
5
%
NORM
AL
CHIL
D L
O
C
K
D
E
LAY
W
ASH
1:21
H
IG
H
W
A
S
H
IN
G
H
IG
H
H
O
T
/
C
O
L
D
S
T
E
A
M
D
O
O
R
L
O
C
K
E
S
T
.
T
I
M
E
:
R
E
M
A
N
I
N
G
5
%
N
O
R
M
A
L
C
H
I
L
D
L
O
C
K
D
E
L
A
Y
W
A
S
H
1:21
H
IG
H
W
A
S
H
IN
G
H
I
G
H
H
O
T
/
C
O
L
D
S
T
E
A
M
D
O
O
R
L
O
C
K
E
ST. T
IM
E
:
R
EM
A
NIN
G
5%
N
O
R
M
A
L
C
H
IL
D
L
O
C
K
D
E
L
A
Y
W
A
S
H
1:21
Tighten
Tighten
PREPARATION BEFORE WASHING
10
1. Fabric Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should
be washed.
2. Sorting
To get the best results, sort clothes into loads that can be washed with the same wash cycle.
Different fabrics need to be washed in different ways.
Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can occur causing
discoloration of white clothing. If possible, do not wash heavily soiled items with lightly soiled ones.
Soil (Heavy, Normal, Light) Separate clothes according to amount of soil.
Color (White, Lights, Darks) Separate white fabrics from colored fabrics.
Lint (Lint Producers, Collectors) Wash lint producers and lint collectors separately.
3. Check before loading
Combine large and small items in a load. Load large items first.
Large items should not be more than half the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
Single bulky items, such as blanket, comforter, or bedspread can be washed separately.
• Check all the pockets to make sure that they are
empty. Things such as clip, matches, pens,
coins, and keys can damage both your washer
and your clothes.
• Close zippers, hooks, and strings to make sure
that these items do not snag on other clothes.
• Pretreat dirt and stains by brushing a little
detergent dissolved in water onto stains like
collars and cuffs to help lift dirt.
WARNING
To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY
INSTRUCTIONS before operating this appliance.
NOTE: Do not wash or spin water-proof clothes.
The washer can be fully loaded, but the drum should not be tightly packed with items. The door of
the washer should close easily.
When unloading items, check under the door seal for small items.
USING THE DISPENSER
ENGLISH
11
The automatic dispenser consists of four compartments which hold 1) liquid chlorine bleach, 2) liquid fabric
softener, 3) liquid or powdered detergent for prewash and 4) liquid or powdered detergent
and color safe bleach for main wash.
All laundry products can be added at once in their respective dispenser compartments.
They will be dispensed at the appropriate time for most effective cleaning. After loading the laundry
additives into the dispenser, close the dispenser drawer.
Add detergent, bleach and fabric softener to the automatic dispenser following these steps:
1. Open the dispenser drawer.
2. Load the laundry products into the appropriate compartments.
3. Close the dispenser drawer slowly to avoid early dispensing of the laundry products.
NOTE: It is normal for small amounts of water to remain in the dispenser compartments at the end of the cycle.
About detergent
• Add detergent to this compartment when using
the Prewash option. Liquid or powdered
detergent may be used in this compartment. The
detergent will automatically be dispensed during
Prewash if the Prewash option is selected.
• Add 1/2 the recommended amount of detergent
to the Prewash compartment and the
recommended amount of detergent to the main
wash compartment.
NOTE : Liquid detergent will drain into the washer
drum as it is added.
1. Prewash Detergent Compartment
Liquid Chlorine
Bleach
Compartment
Liquid Fabric
Softener
Compartment
Prewash
Compartment
Main Wash
Compartment
Your LG TROMM washer is designed to use only High Efficiency (HE) detergents.
HE detergents are formulated specifically for front load washers and contain suds reducing components.
HE detergents make less suds, improve washing and rinsing performance, and help to keep the interior
of your LG TROMM washer clean.
If a regular detergent is used, it may cause oversudsing and unsatisfactory performance.
For the best washing and rinsing performance, low-sudsing HE detergents are strongly recommended.
Designed specially to use only
HE (High Efficiency) detergent
USING THE DISPENSER
12
• Add measured detergent to this compartment for
Main wash. Detergent is flushed from the
dispenser at the beginning of the cycle. Either
powdered or liquid detergent can be used.
• Liquid or powdered color-safe bleach may be
added to the main wash compartment along with
the same type of liquid or powdered detergent.
• When using liquid detergent, make sure the liquid
detergent box and insert are in place. Do not
exceed the maximum fill line.
• For powered detergent, remove both the liquid
detergent box and insert.
• Powdered detergent will not dispense with the
liquid detergent box and insert in place.
2. Main Wash Detergent Compartment
• Add measured liquid chlorine bleach to this
compartment. The bleach will be automatically
dispensed at the proper time during the wash
cycle.
• Do not exceed the maximum fill line. Overfilling can
cause early dispensing of the bleach which could
result in damaged clothes.
• Do not pour undiluted liquid chlorine bleach directly
onto the load or into the drum. Fabric damage can
occur.
• Do not use powdered bleach in this compartment.
3. Liquid Bleach Compartment
• Add recommended amount of fabric softener to
this compartment.
• Dilute concentrated softeners with warm water to
the fill line.
• Do not exceed the maximum fill line. Overfilling can
cause early dispensing of the fabric softener which
could result in stained clothes.
• Do not pour fabric softener directly on the wash
load.
• The fabric softener will be automatically dispensed
during the last rinse cycle.
NOTE: Do not place, store, or spill laundry products
(soap, detergent, bleach, softener, etc.) on the
top of your washer or dryer. These products
can damage the finish or controls if left there
too long.
4. Fabric Softener Compartment
Liquid Detergent
Box
Insert
Designed specially to use only
HE (High Efficiency) detergent
CYCLES
ENGLISH
13
NOTE: To protect your garments, not every Wash/Rinse temperature, spin speed, soil level or option is available with
every cycle.
Select cycles designed for different types of fabric and soil levels.
Cycle
Steam
Fresh
TM
Dress shirts, blouses
Heavily soiled
underwear, work
clothes, diapers, etc
Extra Hot/Cold
High
Extra High
No Spin
Low
Medium
Normal
Heavy
Light
O
OO
O
O
O
OO O
O
O
O
O
O
OO
O
OO
O
O
O
O
O
O
O
O
O
OOOOO
OOO
O
O
O
Normal
Heavy
Light
Normal
Heavy
Light
Normal
Heavy
Light
Normal
Light
Normal
Light
Normal
Heavy
Light
Low
Medium
No Spin
Medium
High
No Spin
Low
High
Extra High
No Spin
Low
Medium
Medium
No Spin
Low
Low
Medium
No Spin
High
Extra High
No Spin
Low
Medium
Warm/Cold
Warm/Warm
Hot/Cold
Cold/Cold
Warm/Cold
Warm/Warm
Hot/Cold
Cold/Cold
Warm/Cold
Warm/Warm
Hot/Cold
Cold/Cold
Cold/Cold
Warm/Cold
Warm/Warm
Cold/Cold
Warm/Cold
Warm/Warm
Extra Hot/Cold
Hot/Cold
Large items such as
blankets and comforters
Dress shirts/pants
wrinkle free clothing,
poly/cotton blend
clothing, table cloths
Cotton, linen, towels,
shirts, sheets, jeans,
mixed loads
Dress shirts/blouses
nylons, sheer or lacy
garment
Items labeled "hand
washable"
Lightly soiled
baby wear
Sanitary
Bulky/Large
Perm Press
Cotton/
Normal
Delicates
Hand Wash/
Wool
Baby Wear
Fabric type
Wash/Rinse
Temp.
Spin Speed Soil Level
Pre-
Wash
Rinse+
Spin
Water
Plus
Stain
Cycle
Steam
Extra
Rinse
Light
Normal
Heavy
Extra High
No Spin
Low
Medium
High
Hot/Cold
Cold/Cold
Warm/Cold
Warm/Warm
Lightly soiled clothing
and small loads
Speed Wash
HOW TO USE THE WASHER
14
• Rotate the Cycle selector knob to select cycle
designed for different types of fabric and soil
levels.
• Each cycle has a preset Water Temperature, Spin
Speed, Soil Level, and Option (See page 13).
• The preset settings can be changed anytime
before Start.
NOTE: This front load washer requires longer cycle time
and gets clothes much cleaner, yet is more gentle
on the fabrics, than top load washers. Washing
time can be reduced significantly for small loads
or lightly soiled loads by selecting Speed Wash
cycle and setting the Soil Level button at Light.
NOTE:
- If you do not press the Start/Pause button within 4
minutes of selecting a cycle, the washer automatically
turns off.
- The LCD will darken after 4 minutes and will be
restored when any button is pressed.
2. Cycles
• Use this button to turn the Power On/Off.
1. Power
• Use this button to start/stop the washer.
3. Start/Pause
■ Steam Wash
• For tough stained clothes, underwear, or baby clothes.
• Steam Wash is available with Sanitary,
Bulky/Large, Perm. Press, Cotton/Normal, and
Baby Wear cycles.
• This option features upgraded washing
performance with low energy and water
consumption.
• Do not load delicates such as wool, silk, and
easily discolored clothes.
NOTE:
- Steam wash is a highly concentrated and efficient.
It may seem there is no water inside the drum, but this
is normal.
- Steam spray may not be seen clearly through the door;
however, the washer is spraying steam strongly inside.
- During the steam operation, a spraying sound will be
heard. This is not a malfunction.
CAUTION:
Do not reach into the washer while operating. Steam
can cause severe burns.
5. Steam
• Allows the start of any cycle to be delayed for
1~19 hours.
• Choose the wash cycle for your load, and then
press the Delay button once for one hour or press
the button again to increase the delay wash time
up to 19 hours in one hour increments, and then
press the Start/Pause button.
4. Delay
DELAY WASH
STEAM
!
HOW TO USE THE WASHER
ENGLISH
15
■ SteamFresh
TM
cycle
•
For slightly wrinkled clothes which have been stored
for an extended time. It makes wrinkled clothes
easier to iron (Do not load wet clothes).
• Wrinkles and odors will be reduced.
• To use the SteamFresh
TM
cycle :
1. Turn on the washer and select the SteamFresh
TM
cycle.
2. Load 5 items or less and close the door.
NOTE: Wipe the water off the drum.
3. Press the Steam button repeatedly until the
correct number of items is displayed.
4. Press the Start/Pause button.
• After the SteamFresh
TM
cycle is complete, the drum
will tumble for 30 minutes to prevent re-wrinkling.
Press any button to unload the items. The Remote
Laundry Monitor (RLM) will display “End” for 2
minutes and then will display “---” for 28 minutes.
• After the SteamFresh
TM
cycle is complete, open the
door and allow it to cool down for best results.
Precautionary Notes:
- The SteamFresh
TM
cycle is not like other washing or
drying cycles.
- Due to the characteristics of cotton fibers, this cycle is
not recommended for 100% cotton clothing.
- Remove stains from clothing before using the
SteamFresh
TM
cycle to prevent permanently setting the
stains by high heat.
- Be sure the faucet is open. This cycle uses a little water
to produce steam.
- Be careful not to touch the door. It can be very hot.
- Do not load the following items:
Wool, blankets, leather jackets, silk, wet clothes,
lingerie, foam products, or electric blankets.
- After removing clothes from the SteamFresh
TM
cycle
they may feel slightly damp. Wait at least 10 minutes
before putting the clothes on.
- Best results are achieved when articles are of similar
size and fabric type. Do not overload.
CAUTION:
- Do not reach into the washer while operating. Steam
can cause severe burns.
- Keep pets away from the washer.
• Press repeatedly to adjust the volume of the
Beeper.
9. Beeper
• Select a water temperature based on the type of
load you are washing.
• Follow the fabric care label and chart below for
best results.
• Warm rinses leave the loads dryer than cold
rinses. Warm rinses increase wrinkling.
• In cold climates, a warm rinse makes the load
more comfortable to handle.
• Cold rinses save energy.
• The Cold rinse temperatures depend on the cold
water at your faucet.
• This washer automatically adjusts the water level
for the type and size of wash load for best results.
It may seem there is no water inside the drum in
some cycles, but this is normal.
6. Wash/Rinse Temperature
• To change the spin speed, press the Spin Speed
button repeatedly to cycle through available
options.
• To start Drain/Spin cycle:
1. Press Power button to turn on.
2. Press Spin Speed button only.
3. Press Start/Pause button.
7. Spin speed (Drain/Spin cycle)
• To change the soil level, press the Soil Level
button repeatedly until the desired setting is on.
8. Soil Level
Suggested Wash Temp.
Garment
Kitchen towels, sheets,
and baby garments
Whites and Heavy
soiled color-fast items
Most loads
Brightly colored items,
washable woolens
Extra Hot
Hot
Warm
Cold
!
HOW TO USE THE WASHER
OPTION
CHILD LOCK
DOOR LOCKED
16
• Use this option for loads that need pretreatment. Adds
16 minutes prewash and a spin cycle.
1. Prewash
• Displays whenever the door of the washer is locked.
• The door can be unlocked by pressing the
Start/Pause button to stop the washer.
NOTE: If the water temperature or the level is too high, the
door cannot be unlocked.
Do not try to force the door open when
is displayed.
STATUS INDICATOR
• It shows elapsed time of the cycle the washer is
operating.
EST. TIME REMAINING
• This display shows the estimated time remaining
in the cycle when operating.
• This washer automatically detects the wash load
(weight) and optimizes the washing time. After
detecting, the display will show the adjusted time
remaining.
• Use this option to prevent unwanted use of the washer.
Press and hold PRE WASH button for 3 seconds to
lock/unlock control.
• When Child lock is set, is displayed and all
buttons are disabled except the Power button. You
can lock the washer while it is operating.
• Adds more time to the wash and rinse cycles for better
stain removal.
• Automatically provides a rinse.
4. Stain cycle
• Adds extra water to the wash and rinse cycles for
superior results.
5. Water Plus
• The Drum Light comes on when the Power button is
pressed. It goes off when the door is closed and the
washer starts operation.
• The Drum Light remains off when the door is locked.
• The Drum Light can be turned on while the washer is in
operation by pressing the Rinse+Spin button for 3
seconds. The light will turn off automatically 4 minutes
later.
• The Drum Light comes on when the washing cycle is
finished and goes off 4 minutes later.
7. Drum Light
• English is the default language.
• Language can be changed only when the LCD is on.
• Power On and then press the Water Plus button for 3
seconds until the SELECT A LANGUAGE menu is
displayed.
• Repeated presses of the Water Plus button will cycle
through "FRANÇAIS" (French), "ESPAÑOL" (Spanish),
and then back to English.
6. Language Selection
• This option provides an additional rinse.
• Use this option to ensure the removal of detergent or
bleach residue from garments.
3. Extra Rinse
• Use this option to rinse and then spin.
2. Rinse+Spin
DOOR LOCK
CHILD LOCK
CHILD LOCK
DOOR LOCK
ENGLISH
17
MAINTENANCE
2
3
1
The water inlet filter
• " " error message will blink on the control panel when water does not enter the dispenser.
• If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged.
We recommend cleaning it every few months.
Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock hazards.
When disposing of the appliance, cut off the power cable, destroy the plug, and disable the door lock to prevent
young children from being trapped inside.
1. Open the lower cover cap (󲾩).
Turn the drain plug (󲾪) to pull
out the hose.
2. Unplug the drain plug 󲾪,
allowing the water to flow out.
At this time use a vessel to
prevent water from flowing
onto the floor. When water does
not flow any more, turn the
pump filter 󲾫 open to the left.
3. Remove any foreign objects from
the pump filter 󲾫. After cleaning,
turn the pump filter 󲾫 clockwise
and insert the drain plug 󲾪 to the
original place. Close the lower
cover cap󲾩.
The drain pump filter
•
The drain filter collects threads and small objects left in the laundry.
Check regularly that the filter is clean to ensure smooth running of your machine.
• Allow the water to cool down before cleaning the drain pump filter.
CAUTION
Drain, using the drain hose, before opening the pump filter to remove objects.
Be careful when draining if the water is hot.
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter using a hard
bristle brush.
4. Tighten the inlet hose.
• IMPORTANT:
Use ONLY the inlet hoses
provided by LG with this laundry
product.
Aftermarket hoses are not
guaranteed to fit or function
correctly. Other hoses may
not tighten correctly and could
cause leaks. Subsequent
damage to product or property
will not be covered under the
terms of LG's warranty.
18
MAINTENANCE
Cleaning the Dispenser
•
The dispenser may need to be cleaned periodically due to laundry additive build-up.
• Run warm water and use a soft brush or cloth on the drawer, liquid detergent box and inserts to remove any excess
laundry additives.
• Clean the drawer opening using water and a small brush.
• Follow the illustrations in reverse order to replace the parts to their proper location.
NOTE: Do not use any cleaning substance on the drawer opening other than water because it will drain into the tub.
If this should happen, set the washer for a rinse and spin cycle to remove any cleaning substance from the
washer before doing a load of laundry.
The washing drum
• Remove items from the washer as soon as the cycle is completed. Wrinkling, color transfer, and odors may be
produced in items left in the washing drum.
• If you live in a hard water area, lime scale can continuously build up in places where it cannot be seen
and it is not easily removed from the drum.
Over time the build-up of scale clogs appliances, and if it is not kept in check, these will eventually
have to be replaced.
• Although the washing drum is made of Stainless steel, specks of rust can be caused by small metal articles
(paper clips, safety pins, etc.) which have been left in the drum.
• The washing drum should be cleaned from time to time.
• If you use descaling agents, dyes, or bleaches, make sure they are suitable for washing machine use.
• Descaler could contain components that can damage part of your washing machine.
• Remove the spots with a stainless steel cleaning agent.
• Never use steel wool.
1


Pull the dispenser
drawer out until it stops.
2
Press down the lock tab
on the bleach insert.
Remove the drawer.
3
Remove the liquid detergent
box, softener and bleach
inserts from their
compartments.


ENGLISH
19
MAINTENANCE
The water circulation & steam nozzle
• Clean the nozzle, if clogged.
Cleaning your washer
1. Exterior
Proper care of your washer can extend its life.
The outside of the machine can be cleaned with warm water and a neutral, non-abrasive
household detergent.
Immediately wipe off any spills with a damp cloth.
Try not to damage the surface with sharp objects.
󳀌 IMPORTANT: Do not use methylated spirit, solvents or similar products.
2. Interior
Dry around the washer door opening, door seal and door glass. These areas should always be clean to ensure
a water-tight seal.
TUB CLEAN is a special cycle for cleaning the inside of the washer. This cycle uses higher water level with
higher spin speed. Perform this cycle regularly.
• To start the TUB CLEAN cycle:
1. Remove any clothing or items from the washer and close the door.
2. Open the dispenser drawer and add liquid chlorine bleach to the bleach compartment.
NOTE: Do not add any detergent to the detergent compartments. Excessive suds may be produced and leak
from the washer.
3. Close the dispenser drawer slowly.
4. Power On and then press the Extra Rinse button for 3 seconds. (Prewash option will be selected.)
5. Press the Start/Pause button to start.
6. After the cycle is complete, leave the door open to dry around the washer door opening, door seal and
door glass.
CAUTION: If there are small children in the house, care must be taken so that they can not climb into or
play inside the washer while it is open for drying.
NOTE: Remove hard water deposits using only cleaners labeled as safe for washing machines.
Winterizing instructions
If the washer is stored in an area where freezing can occur or moved in freezing temperatures, follow these
winterizing instructions to prevent damage to the washer:
1. Turn off water supply tap.
2. Disconnect hoses from water supply and drain water from hoses.
3. Plug electrical cord into a properly grounded electrical outlet.
4. Add 1 gallon (3.8
) nontoxic recreational vehicle (RV) antifreeze to empty wash drum. Close door.
5. Set spin cycle and let washer spin for 1 minute to drain out all the water.
Not all of the RV antifreeze will be expelled.
6. Unplug electrical power cord, dry drum interior, and close door.
7. Remove the two-compartment container from the Dispenser. Drain any water in compartments and dry the
compartments.
8. Store washer in an upright position.
9. To remove antifreeze from washer after storage, run empty washer through a complete cycle using detergent.
Do not add laundry.
!
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

LG WD-13514BDM Le manuel du propriétaire

LG
Marque
LG
Modèle
WD-13514BDM
Catégorie
Machines à laver
Taper
Le manuel du propriétaire
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents