WIKA CPC2000 Mode d'emploi

Operating instructions

Betriebsanleitung

Mode d'emploi

Manual de instrucciones

EN

FR

DE

ES

Portable low-pressure controller, model CPC2000

Portabler Niederdruckcontroller, Typ CPC2000

Contrôleur basse pression portable, type CPC2000

Controlador portátil de bajas presiones, modelo CPC2000

Portable low-pressure controller model CPC2000

2

11155094.04 11/2019 EN/DE/FR/ES

WIKA operating instructions, model CPC2000

EN

DE

ES

FR

Operating instructions model CPC2000 Page 3 - 42

Betriebsanleitung Typ CPC2000 Seite 43 - 82

Mode d'emploi type CPC2000 Page 83 - 122

Manual de instrucciones modelo CPC2000 Página 123 - 162

Further languages can be found at www.wika.com.

WIKA

®

is a registered trademark in various countries.

WIKA

®

ist eine geschützte Marke in verschiedenen Ländern.

Prior to starting any work, read the operating instructions!

Keep for later use!

Vor Beginn aller Arbeiten Betriebsanleitung lesen!

Zum späteren Gebrauch aufbewahren!

Lire le mode d‘emploi avant de commencer toute opération !

A conserver pour une utilisation ultérieure !

¡Leer el manual de instrucciones antes de comenzar cualquier trabajo!

¡Guardar el manual para una eventual consulta!

3WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

Contents

1. General information 5

2. Short overview 6

2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Description . . . . . . . . . . . . . . . . . . . . . . . 6

2.3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . 7

3. Safety 7

3.1 Explanation of symbols . . . . . . . . . . . . . . . . . . . 7

3.2 Intended use . . . . . . . . . . . . . . . . . . . . . . . 8

3.3 Improper use . . . . . . . . . . . . . . . . . . . . . . . 8

3.4 Personnel qualification . . . . . . . . . . . . . . . . . . . 9

3.5 Labelling, safety marks . . . . . . . . . . . . . . . . . . . 10

3.5.1 Product label (example). . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

3.5.2 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4. Design and function 11

4.1 Electrical connections . . . . . . . . . . . . . . . . . . . .11

4.2 Voltage supply . . . . . . . . . . . . . . . . . . . . . . 11

4.2.1 Power supply unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

4.2.2 Lithium-ion rechargeable battery. . . . . . . . . . . . . . . . . . . . . . . .12

4.2.3 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

4.3 Pressure connections . . . . . . . . . . . . . . . . . . . .14

4.3.1 Connection of the test item . . . . . . . . . . . . . . . . . . . . . . . . . . .14

4.3.2 Overpressure protection . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

4.4 User interface . . . . . . . . . . . . . . . . . . . . . . 15

5. Transport, packaging and storage 17

5.1 Transport . . . . . . . . . . . . . . . . . . . . . . . . 17

5.2 Packaging and storage . . . . . . . . . . . . . . . . . . . 17

6. Commissioning, operation 18

6.1 Location . . . . . . . . . . . . . . . . . . . . . . . . 18

6.2 Mechanical mounting . . . . . . . . . . . . . . . . . . . .18

6.3 Measurement principle . . . . . . . . . . . . . . . . . . . 18

6.4 Switching on the low-pressure controller . . . . . . . . . . . . . 19

6.5 Operating mode Control “CTRL” . . . . . . . . . . . . . . . . 19

6.6 Operating mode Measure “MEAS”. . . . . . . . . . . . . . . . 21

6.7 Operating mode AUTOMATIC-MODE “AUTO”. . . . . . . . . . . . 22

6.8 Leakage “LEAK”. . . . . . . . . . . . . . . . . . . . . . 25

4 WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

Declarations of conformity can be found online at www.wika.com.

Contents

6.9 SETUP settings (SETUP) . . . . . . . . . . . . . . . . . . 26

6.9.1 The menu items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

6.9.2 SETTINGS submenu item . . . . . . . . . . . . . . . . . . . . . . . . . . .27

6.9.2.1 ZERO submenu item . . . . . . . . . . . . . . . . . . . . . . . . . . .28

6.9.2.2 RS232/USB submenu item. . . . . . . . . . . . . . . . . . . . . . . .28

6.9.2.3 DISPLAY submenu item . . . . . . . . . . . . . . . . . . . . . . . . .28

6.9.2.4 AUTO-MODE submenu item. . . . . . . . . . . . . . . . . . . . . . .29

6.9.2.5 INFO submenu item . . . . . . . . . . . . . . . . . . . . . . . . . . .29

7. Interface 30

7.1 USB interface. . . . . . . . . . . . . . . . . . . . . . . 30

7.2 RS-232 interface . . . . . . . . . . . . . . . . . . . . . 30

7.3 Interface configuration. . . . . . . . . . . . . . . . . . . . 30

7.4 Commands for serial interface . . . . . . . . . . . . . . . . .31

7.5 Driver . . . . . . . . . . . . . . . . . . . . . . . . . 34

8. Faults 35

9. Maintenance, cleaning and recalibration 36

9.1 Maintenance . . . . . . . . . . . . . . . . . . . . . . .36

9.2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . 36

9.3 Recalibration . . . . . . . . . . . . . . . . . . . . . . .37

10. Dismounting, return and disposal 37

10.1 Dismounting . . . . . . . . . . . . . . . . . . . . . . 37

10.2 Return. . . . . . . . . . . . . . . . . . . . . . . . . 37

10.3 Disposal . . . . . . . . . . . . . . . . . . . . . . . .38

11. Specifications 39

12. Accessories 42

5WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

1. General information



The model CPC2000 low-pressure controller described in the operating instructions

has been designed and manufactured using state-of-the-art technology. All

components are subject to stringent quality and environmental criteria during

production. Our management systems are certified to ISO 9001 and ISO 14001.



These operating instructions contain important information on handling the instrument.

Working safely requires that all safety instructions and work instructions are observed.



Observe the relevant local accident prevention regulations and general safety

regulations for the instrument's range of use.



The operating instructions are part of the product and must be kept in the immediate

vicinity of the instrument and readily accessible to skilled personnel at any time. Pass

the operating instructions on to the next operator or owner of the instrument.



Skilled personnel must have carefully read and understood the operating instructions

prior to beginning any work.



The general terms and conditions contained in the sales documentation shall apply.



Subject to technical modifications.



Factory calibrations / DKD/DAkkS calibrations are carried out in accordance with

international standards.



Further information:

Mensor LP

- Internet address: www.mensor.com

- Relevant data sheet: CT 27.51

- Application consultant: Tel: +1-512-396-4200

Fax: +1-512-396-1820

sales@mensor.com



EU importer

WIKA Alexander Wiegand SE & Co. KG

- Internet address: www.wika.de / www.wika.com

- Relevant data sheet: CT 27.51

- Application consultant: 

Fax: +49 9372 132-406

info@wika.de

6 WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

2. Short overview

2.1 Overview

1

Low-pressure controller model CPC2000

2

Function buttons

3

Handle

4

Display

5

Pressure connections

2.2 Description

The microprocessor-controlled model CPC2000 low-pressure controller is a mains- or

battery-operated pressure controller with internal, automatic pressure generation and

pressure reference. The pressure generation is achieved using an integrated, electric

pump, which makes a positive and/or negative pressure available on both the tube

connections:

The CPC2000 delivers:



Simple generation of positive and negative reference pressures



Pressure measurement of positive and negative pressures



Differential pressure measurement



Identification of leaks of a test item

1

2

3

5

4

2. Short overview

7WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

2.3 Scope of delivery



Portable low-pressure controller model CPC2000



Power supply unit



Operating instructions



Calibration certificate

Cross-check scope of delivery with delivery note.

2. Short overview / 3. Safety

3. Safety

3.1 Explanation of symbols

WARNING!

... indicates a potentially dangerous situation that can result in serious injury or

death, if not avoided.

CAUTION!

... indicates a potentially dangerous situation that can result in light injuries or

damage to property or the environment, if not avoided.

DANGER!

... identifies hazards caused by electrical power. Should the safety instructions

not be observed, there is a risk of serious or fatal injury.

DANGER!

... indicates a potentially dangerous situation in the hazardous area that can

result in serious injury or death, if not avoided.

Information

... points out useful tips, recommendations and information for efficient and

trouble-free operation.

8 WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

3. Safety

3.2 Intended use

The model CPC2000 low-pressure controller is used for testing and calibrating pressure

sensors.

This instrument is not permitted to be used in hazardous areas!

The instrument has been designed and built solely for the intended use described here,

and may only be used accordingly.

The technical specifications contained in these operating instructions must be observed.

Improper handling or operation of the instrument outside of its technical specifications

requires the instrument to be taken out of service immediately and inspected by an

authorised WIKA service engineer.

Handle electronic precision measuring instruments with the required care (protect from

humidity, impacts, strong magnetic fields, static electricity and extreme temperatures,

do not insert any objects into the instrument or its openings). Plugs and sockets must be

protected from contamination.

The manufacturer shall not be liable for claims of any type based on operation contrary to

the intended use.

3.3 Improper use

DANGER!

Danger to life from explosion!

Improper use of the low-pressure controller may result in a risk of explosion,

which may lead to serious injury or death, as the built-in lithium-ion

rechargeable battery may explode.



Do not burn or heat up the low-pressure controller.



Never store the low-pressure controller close to fire, ovens or other

high-temperature locations.



Never place the low-pressure controller in a hermetically sealed container.

In some cases hydrogen or oxygen may be discharged from the lithium-ion

rechargeable batteries, which may result in rupture, fire or explosion.

WARNING!

Injuries through improper use

Improper use of the instrument can lead to hazardous situations and injuries.



Refrain from unauthorised modifications to the instrument.



Do not use the instrument within hazardous areas.



There must be no external pressure acting on the CPC2000.



Observe the operating parameters in accordance with chapter

11 “Specifications”.

9WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN



Do not use the instrument if it is damaged. Before using the instrument,

check that there are no cracks on the case or any missing plastic parts.



Select the proper function and correct measuring range for the

measurement.



Always operate the instrument within the defined pressure range.



Do not use the instrument if it is not working properly. The instrument

protection might be compromised. If in doubt, have the instrument checked.



Before starting the pressure measurement, ensure that the low-pressure

controller has been switched to a depressurised state and the test item is

correctly connected.



Only use the accessories specified and authorised by WIKA.

Any use beyond or different to the intended use is considered as improper use.

Do not use this instrument in safety or emergency stop devices.

3.4 Personnel qualification

WARNING!

Risk of injury should qualification be insufficient

Improper handling can result in considerable injury and damage to equipment.



The activities described in these operating instructions may only be carried

out by skilled personnel who have the qualifications described below.

Skilled personnel

Skilled personnel, authorised by the operator, are understood to be personnel who,

based on their technical training, knowledge of measurement and control technology and

on their experience and knowledge of country-specific regulations, current standards and

directives, are capable of carrying out the work described and independently recognising

potential hazards.

3. Safety

10 WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

3.5 Labelling, safety marks

3.5.1 Product label (example)

The product label is located on the rear of the CPC2000.

1

Supply voltage

2

Pressure medium

3

Operating temperature

4

Pressure range

5

Accuracy

6

Serial number

7

Year of manufacture

3.5.2 Explanation of symbols

Before mounting and commissioning the instrument, ensure you read the

operating instructions!

Do not dispose of with household waste. Ensure a proper disposal in

accordance with national regulations.

Li-Ion

Mensor LP San Marcos Texas 78666 USA

2014

Year of manufacturing:

12344414Serial no.:

± 0,3% FSAccuracy:

0... < > hPaPressure range:

+10°C to 40°C

Operating temperature:

ambient airPressure medium:

24 VDC

Power supply:

Portable low-pressure controller

CPC2000

1

2

3

4

5

6

7

3. Safety

11WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

4. Design and function

4.1 Electrical connections

The electrical connection is located on the rear of the CPC2000.

4.2 Voltage supply

The low-pressure controller is factory-set for connection to a voltage supply of DC 24 V.

The connection for the power supply unit is located on the rear of the instrument.



The mains plug of the charger/power supply unit must always be plugged into a mains

socket and accessible, so that one can always remove it from the mains socket without

difficulty.



The internal lithium-ion rechargeable battery, which can be easily charged with the

battery charger supplied with the equipment, serves as the voltage supply for the

instrument.

4.2.1 Power supply unit

DANGER!

Danger to life caused by electric current

Upon contact with live parts, there is a direct danger to life.



With operating or charging using a defective or non-original power supply

unit (e.g. short-circuit from the mains voltage to the output voltage), this can

result in life-threatening voltages at the instrument!



Only use the power supply unit supplied with the instrument (original power

supply unit, Mascot model 9926)!



Only use a battery charger that is fully functional or undamaged.



If there is any visible damage to the case or the wiring, do not use the power

supply unit!

1

USB interface

2

RS-232 interface

3

Connection for power

supply unit

1

3

2

12 WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

Never install nor store the power supply unit in the following locations, as this can lead to

a failure in operation:



Places where there is strong humidity or condensation



Outdoors

Application



The power supply unit is maintenance-free. It must not be opened (danger of electrical

shock).



Disconnect the power supply unit from the mains supply when it won't be used for a

longer period of time.

Permissible conditions at the place of use



Ambient temperature: 0 ... 45 °C [32 ... 113 °F]



Humidity: up to 90 % relative humidity (no condensation)

Cleaning



Before cleaning, disconnect the power supply unit from the mains supply.



Do not clean with chemical cleaning agents.



Only clean with a dry cloth.

4.2.2 Lithium-ion rechargeable battery

The integrated lithium-ion rechargeable battery is subject to the requirements

of the Dangerous Goods Directive. Special requirements for packaging and

labelling must be observed when shipping. A dangerous goods expert must be

consulted when preparing the package.

Do not ship the CPC2000 if the rechargeable battery is damaged or defective.

Observe the different dangerous goods requirements relative to the respective

modes of transport and any other national regulations.



The rechargeable battery is built in permanently to the model CPC2000 low-pressure

controller.



The battery life for the rechargeable battery is up to 8 hours in continuous operation.



The battery can be charged only using the power supply unit included in the scope of

delivery.

Should the rechargeable battery in the low-pressure controller stop working,

contact WIKA. The instrument must not be opened under any circumstances.

For contact details see chapter 1 “General information” or the back page of the

operating instructions.

4. Design and function

13WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

Charging the lithium-ion rechargeable battery

DANGER!

Injuries, material and environmental damage due to an improper

charging of the lithium-ion rechargeable battery!

Improper charging of the lithium-ion rechargeable battery can immediately

lead to dangerous situations and serious injuries, since the built-in lithium-ion

rechargeable battery can explode, heat up or ignite.



Only use the power supply unit supplied with the instrument!



Never leave the low-pressure controller near fire, nor in direct sunlight. If the

lithium-ion rechargeable batteries become hot, the built-in safety device is

activated and overcharging prevented. Heating the lithium-ion rechargeable

batteries can damage the safety device and can thus lead them to heat up

further, to cease to work or to ignite.



Do not continue to charge the low-pressure controller if it does not fully

recharge within the specified time (approx. 8 hours).

WARNING!

Injuries or damage to property through defective rechargeable battery

A defective rechargeable battery can lead to hazardous situations and injuries.



The CPC2000 low-pressure controller must absolutely not be used if, while

using, charging, or storing, it emits an unusual smell, feels hot or appears

abnormal in any other way.



The temperature range over which the lithium-ion rechargeable battery can be

charged is 0 ... 45 °C [32 ... 113 °F]. Temperatures outside of the specifications lead,

during the charging process, to heating or destruction to the rechargeable battery.



Do not charge the lithium-ion rechargeable battery outside this temperature range. In

addition to this range, the performance of the lithium-ion rechargeable battery can be

affected and the service life reduced.



Do not leave the rechargeable battery connected to the power supply unit for longer

than one day, since overcharging can shorten its service life.



When not being used, a fully charged battery will lose its charge over time.

4.2.3 Interface

It is possible to control and monitor the controller via a PC using interfaces (USB or

RS-232). For more information on this, please refer to chapter 7 “Interface”.

4. Design and function

14 WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

4.3 Pressure connections

Only use original parts (see chapter 12 “Accessories”).

The pressure connections are located on the right-hand side of the front of the CPC2000.

Mechanical and also electrical pressure measuring instruments can be connected.

The hose, lines and fittings etc. must always be approved at least for the working pressure

which corresponds to the pressure of the instrument. In addition, there must not be any

leakage points during the calibration.

4.3.1 Connection of the test item

The connection to the low-pressure controller is made via a 6.6 x 11 mm pressure

connection. The hose diameter should be 6 mm.





instrument.





open to atmosphere).





connection is open to atmosphere).

Only connect test and calibration installations once the system has been

depressurised!

4.3.2 Overpressure protection

The maximum permissible pressure must not be exceeded, see chapter

11 “Specifications”.

4. Design and function

15WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

4. Design and function

4.4 User interface

The CPC2000 low-pressure controller can be operated via its clearly structured display

and control panel.

Function buttons

Pos. Button Meaning

1

LEAK

LEAK button

With the [LEAK] button, an instrument connected to the controller

can be tested for leaks. (This feature is only possible in CONTROL

mode.)

2

MENU

MENU button

With this button the SETUP menu can be accessed, and there the

settings for each operating mode can be made. When the CTRL

mode is used, you will find that the instrument is left in VENT mode

on leaving the SETUP menu.

The SETUP menu items are made up of six submenu items. For a

detailed description of these items, see chapter 6.9 “SETUP settings

(SETUP)”.

3

Increase set point

Change pressure in % via [▲] button

4

Increase set point to 100 %

Change pressure to 100 % via [▶] button

1 2 3 4

5

7 689

16 WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

Pos. Button Meaning

5

I / 0

On/Off button

Button to turn the instrument on and off.

6

SELECT

SELECT button

[SELECT] button to confirm the preceding entry.

7

Decrease set point

Change pressure in % via [▼] button

8

Decrease set point to 0 %

Change pressure back to 0 % via [◀] button

9

ZERO

ZERO button

[ZERO] button for manually zero point correction of the integrated

sensor.

External influences such as temperature, position or ambient

pressure may cause the zero point of the instrument, i.e. the

display with pressure inputs open, to change. During the zero point

correction, the instrument automatically determines these changes

and calculates them into the current pressure display. The zero point

correction requires a switching of the internal valves, which is not

possible without pressure loss.

(If this should interfere with the application, the automatic zero point

correction can be switched off.)

The display screen behind the foil is made from glass. If there is any possibility

of the screen breaking during operation, incl. destruction of the front foil, all

personnel in the vicinity of the instrument must wear safety goggles before and

during its use.

Further definitions

[XXX] Press XXX button

“XXX” Menu XXX will be selected

XXX Menu XXX will be displayed

4. Design and function

17WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

5. Transport, packaging and storage

5.1 Transport

Check the low-pressure controller for any damage that may have been caused by

transport. Obvious damage must be reported immediately.

CAUTION!

Damage through improper transport

With improper transport, a high level of damage to property can occur.



When unloading packed goods upon delivery as well as during internal

transport, proceed carefully and observe the symbols on the packaging.



With internal transport, observe the instructions in chapter 5.2 “Packaging

and storage”.

If the instrument is transported from a cold into a warm environment, the formation of

condensation may result in instrument malfunction. Before putting it back into operation,

wait for the instrument temperature and the room temperature to equalise.

5.2 Packaging and storage

Do not remove packaging until just before mounting.

Keep the packaging as it will provide optimum protection during transport (e.g. change in

installation site, sending for repair).

Permissible conditions at the place of storage:



Storage temperature: -10 ... +70 °C [14 ... 158 °F]



Humidity: 30 ... 80 % relative humidity (no condensation)

Avoid exposure to the following factors:



Direct sunlight or proximity to hot objects



Mechanical vibration, mechanical shock (putting it down hard)



Soot, vapour, dust and corrosive gases



Hazardous environments, flammable atmospheres

Store the low-pressure controller in its original packaging in a location that fulfils the

conditions listed above. If the original packaging is not available, pack and store the

instrument as described below:

1. Wrap the instrument in an antistatic plastic film.

2. Place the instrument, along with the shock-absorbent material, in the packaging.

3. If stored for a prolonged period of time (more than 30 days), place a bag containing a

desiccant inside the packaging.

18 WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

6. Commissioning, operation

Personnel: Skilled personnel

Only use original parts (see chapter 12 “Accessories”).

6.1 Location

An unsafe stand or vibration can influence the measurement or lead to injury.



Make sure that the low-pressure controller is placed on a secure surface during

operation.



Make sure that the surface is stable.

6.2 Mechanical mounting

CAUTION!

Damage to the instrument

To avoid possible damage to the CPC2000 or to the test assembly, pay

attention to the following:



Only connect test and calibration installations once the system has been

depressurised (atmospheric).



The maximum pressure is P

max

= 1 bar atmospheric pressure



This pressure must NEVER be exceeded.

6.3 Measurement principle

Microprocessor

Set-actual value

comparison

Valves

pos.

pressure

neg.

pressure

RS-232 PC interface

USB interface

Display

-

+

Actual pressure

value

Pressure value

Controllers

Pump

Pressure

measurement

19WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

6. Commissioning, operation

6.4 Switching on the low-pressure controller

By pressing the [On/Off] button, the model CPC2000 low-pressure controller is switched

on.

As soon as the instrument is switched on, a zero point correction is automatically carried

out, so that a zero-point drift is eliminated.

The controller requires a warm-up time of a few minutes (max. 15 minutes) to reach its

specified accuracy. Large changes in ambient temperature may make a longer warm-up

period necessary.

The subsequent preparation of a calibration requires only a few settings.



First, using the [MENU] button, select one of the stored pressure units and the variable

pressure change step in the range of 0 ... 50 %.



Then, once the full scale has been entered in Control mode, the pressure can be

easily increased or decreased by the defined level using the navigation buttons.



To check whether the calibration assembly or the test item has a leak, the [LEAK]

button can be used. With this, the pressure is locked into the test assembly and

any pressure drop there might be, as well as the time this takes, is measured and

displayed.

Never perform functional tests with compressed or medical air. This can

damage instruments with low pressure ranges.

Protect the instrument from sunlight, as this can lead to measuring errors.

6.5 Operating mode Control “CTRL”

The CTRL mode is used for the calibration of pressure sensors and other pressure

instruments. In CTRL mode, the pump is active and regulates according to the desired

pressure. The internal sensor provides the current value on the display.

Setting

1. Press the [MENU] button.

2. Confirm the menu item MODE with [SELECT] and press the [▲] / [▼] buttons until

CTRL is displayed.

3. Confirm with [SELECT].

4. In the RANGE submenu, the upper limits of the pressure range are defined with the

[▲] / [▼] and [◀] / [▶] buttons.

5. Confirm with [SELECT].

6. In the UNIT submenu, define the pressure unit with the [▲] / [▼] buttons.

7. Confirm with [SELECT].

8. In the STEPS submenu, the step sequence in % is defined with the [▲] / [▼] and [◀] /

[▶] buttons.

9. Confirm with [SELECT].

10. With the [MENU] button, you can exit the submenu.

20 WIKA operating instructions, model CPC2000

11155094.04 11/2019 EN/DE/FR/ES

EN

Operation

The instrument will revert to VENT mode

on exiting the menu, meaning the sensor

of the controller will be vented. In the

top centre of the display, the set point

of the pressure range will be displayed.

In the bottom centre of the display, the

percentage value can be read. On exiting

the menu, this value will be 0 %.



With the [SELECT] button, one can

switch between the target pressure

specification and the percentage value.



The percentage value can be changed with the [▲] or [▼] buttons (in the defined step

sizes) and with the [◀] or [▶] buttons.



The target pressure specification can only be changed with the [▲] or [▼] buttons.

With the [◀] or [▶] buttons, you can jump to the location of the target pressure

specification.

As soon as the controller display indicates a stable value, the data can be recorded:

In CTRL mode it is possible to adjust the zero point of the controller manually and to

check the connected instrument for leaks.

Function Meaning

Manual zero point

correction

Confirm with [ZERO] button and the reference measuring cell of the

instrument will be adjusted.

Change set point to x %:

Change pressure in % via the [▲] or [▼]

buttons

Change pressure to 100 % via the [▶]

button

Change pressure back to 0 % via the [◀]

button

1

Full scale

2

Pressure unit

3

Measured value

4

Set point in % of full scale

5

Battery status

6

Operating mode

+04.999

+10.000

CTRL

mbar

+ 50% +5.000

1

2

3

4

5

6

6. Commissioning, operation

La page charge ...

WIKA CPC2000 Mode d'emploi

Ce manuel convient également à

WIKA CPC2000 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents