Norcold N2090 Guide d'installation

Refrigerator

N2000 Series

Install Manual

Norcold, Inc.

P.O. Box 4248

Sidney, OH 45365-4248

Norcold Customer Service Dept.

Telephone: 800-543-1219

Fax: 734-769-2332

Website: www.norcold.com

Index

ENGLISH 3

2

Contents

1. Introduction ..................................................................................................... 3

2. Symbols ............................................................................................................ 3

3. Regulations and Standards .............................................................................. 3

4. Serviceability .................................................................................................... 4

5. Position and placement ................................................................................... 5

6. Prepare for installation (N2090 only)............................................................... 6

7. Connecting electrical supplies.......................................................................... 9

8. Mounting the refrigerator ............................................................................. 14

9. Ventilation...................................................................................................... 17

10. Installing the door panel .............................................................................. 21

11. Door Conversion .......................................................................................... 24

12. Warranty and servicing ................................................................................ 26

EN

Original Installation Manual

3

1. Introduction

This is the installation manual for the Norcold N2000 series refrigerator. The manual is meant for

qualified installers who will install the refrigerator in a mobile leisure vehicle. Read the information

and instructions carefully and follow them strictly to install the refrigerator safely and correctly.

Also read the warnings in the user manual before testing the refrigerator after installation.

Our policy is one of continuous development and improvement. Specifications and illustrations

may change subsequent to publication.

If the appliance is not installed in accordance with national regulations, rules and

standards this will void the warranty.

2. Symbols

Key to symbols:

Warning.

Risk of serious injury and/or damage.

Caution.

Risk of injury and/or damage.

Attention.

Important information.

Note.

Additional information.

3. Regulations and Standards

Do not modify this appliance unless the modification is authorized and carried out by

the manufacturer or their agent.

For installations which need an electric outlet that is energized by an external power

source, the refrigerator must be electrically grounded as written in local codes or the

National Electrical code, NFPA 70.

Use only genuine and approved parts and materials.

Wear the correct Personal Protective Equipment during the installation. Also follow the

applicable safety regulations.

Electrical appliances should only be installed by qualified and certified professionals.

The electronic connections must be installed in accordance with the latest technical

regulations.

4

Make sure the refrigerator is transported and handled in the upright position, or on its

side with the electronics facing down as depicted in the section Installing door panel.

After the refrigerator has been transported and/or been laid on its side, let the

refrigerator stay upright for 30 minutes before switching on.

Install the refrigerator in accordance with the local/national laws.

Do not spray liquids near electrical outlets, connections, or refrigerator components.

Many liquids are electrically conductive and can cause a shock hazard, electrical shorts

and in some case fire.

Never open or damage the cooling system at the back or on the inside of the refrigerator.

The cooling system is pressurized and contains flammable substances.

The performance of the refrigerator may be affected by adjacent heat sources such as an

oven or stove. Protect the refrigerator against any heat sources by fitting insulation.

Never reposition or change the electronic components.

In order to prevent the risk of fire in the event of uncontrolled leakage of the refrigerant

system, make sure that the refrigerant charge per net room volume does not exceed

0.0005lb/ft

3

. Net room volume is defined as the gross room volume minus the volume of

any product, equipment, or objects located in the living area. The refrigerant charge

amount can be found on the serial label.

Make sure no equipment that produces sparks or flames is installed close to the cooling

system.

Any error messages coming from the refrigerator should not disturb the driver. For

example: flashing of the display to indicate an error while driving.

Do not use the drawer as a step or ladder.

The refrigerator is intended to be used in a recreational vehicle. The refrigerator is not

suited for use other than in a recreational vehicle.

4. Serviceability

The installer of Norcold products is responsible for proper installation to ensure the correct

Functionality and serviceability of the appliance. In terms of serviceability, this means that a

dealer or an authorized Norcold service partner must be able to remove and re−install the

Norcold products within the time that is allowed according to the Norcold time−list, using

standard tools and equipment.

This is to claim any warranty during the period of 1 years after purchase date. In case of any queries

on this subject, please contact the Norcold local service representative before installing the product.

5

5. Position and placement

•

Use the mounting dimensions as shown below.

Table 1: Mounting dimensions

Model H W D FL FH A

N2090

38.7in

[982mm]

16.5in

[420mm]

19.9in

[506mm]

0.8in

[21mm]

0.8in

[20mm]

0.8in

[20mm]

N2152 59.2in

[1504mm]

16.5in

[420mm]

22.3in

[567mm]

1.7in

[42mm]

1.1in

[28mm]

1.6in-2.4in

[40mm−60mm]

N2160 49.2in

[1249mm]

20.7in

[527mm]

22.2in

[563mm]

2.2in

[55mm]

0.1in

[3mm]

0.2in

[5mm]

N2175 49.2in

[1249mm]

20.7in

[527mm]

23.7in

[613mm]

2.2in

[55mm]

0.1in

[3mm]

0.2in

[5mm]

FL

H

A

FH

6

6. Prepare for installation (N2090 only)

Installing insulation material is strongly recommended. It will considerably reduce the emitted

noise and protects against heating up from outside the vehicle. For information on the correct

type of insulation, contact the supplier.

•

Install insulation on the back of the chassis.

Top model

7

Floor model

The insulation material should be left exposed and not covered by paneling to prevent

unwanted reflection of noise.

Ensure that the insulation material is able to handle the temperatures and the mechanical

loading expected during normal use.

Ensure that the insulation material does not diminish the minimal ventilation dimensions

of the air ducts. Glued insulation material might detach over time and block the airways.

Overheating of the system might be a result.

For the correct type of insulation, it is advised to use a polyurethane noise absorption

panel with open cell structure, or similar.

•

Make a cut−out in the roof panel, exposing the insulation material.

•

Seal any gaps between furniture and chassis to prevent noise emission.

8

Drainage tube (N2090 only)

This refrigerator has the possibility to drain condensation directly to the outside. Then the end

user does not have to empty the drip tray via the inside of the refrigerator. For this, you can

extend with your own tube (external Ø 0.35in [9mm], inner Ø 0.20in [5mm]) coming out of the

refrigerator at the back, and guide this tube directly to the outside of the vehicle.

9

7. Connecting electrical supplies

•

Use the following values to connect the power supply.

Table 2: Power supply values

The electrical connections must comply with IEC/UL/EN60335−1.

Connect the device to an on-board battery in the vehicle. This battery should be

exclusively intended for powering on−board devices. Connecting to the engine battery is

not suitable.

Ensure that wires can't come into contact with hot or sharp parts.

The 12V power supply wiring should incorporate a general main switch that enables all

pole disconnection of the 12V appliances from the 12V power supply source.

Ensure that the Battery Discharge Protection Circuit is used to prevent damage to the 12V

battery when the battery is at low charge.

The factory setting for the cut−in/cut−out voltage is 10.4V (cut−out) and 11.7V (cut−in). For trailer

applications without on−board battery, this setting can be changed to 11.3V (cut−out) and 12.5V

(cut−in).

To change the cut−in/cut−out setting:

•

Open the door.

•

Unlock the control panel, if applicable, by pressing the fresh food, frozen food or night mode

area. Hold it for a few seconds until the icons blink twice to be able to adjust the setting.

DC 12V

Power requirement 12V DC 10.4−16.0V at the refrigerator

Cable dimensions (Cable thickness vs cable

length)

•

14 AWG =< 8ft [2.5mm

2

= ‹ 2.5m]

•

12 AWG =< 13ft [4mm

2

= ‹ 4m]

•

10 AWG =< 20ft [6mm

2

= ‹ 6m]

Fuse current 15A in power supply system near the power

supply source

DC supply

Red cable (+) and white cable (−)

12V power connector

Refrigerator: Stocko VV 2041.100-G or

equivalent

Supply cable counterpart: Stocko VV 2041.200

-

G

or equivalent

10

•

Open the extra settings mode by pressing the night mode area for 10 seconds. The fresh

food icons blink 2 times.

•

Press on the fresh food area for 1 second to adjust the setting:

− Icons 1 and 5 on: 10.4V (cut−out) and 11.7V (cut−in) (factory setting).

− Icons 2, 3 and 4 on: 11.3V (cut−out) and 12.5V (cut−in).

•

After a few seconds, the control panel will save the settings and go to the locked stand−by

mode.

11

Wiring diagram:

1.

Main PCBA cooling unit

2.

Fuse 15 A

3.

Input power 12V DC

4.

LED module

5.

Interior refrigerator thermistor

6.

Display module

7.

Fan cooling unit

N2090

1

2

3

4

7

6

5

12

1.

Main PCBA cooling unit

2.

Fuse 15A

3.

Input power 12V DC

4.

Interior Fan

5.

Fan cooling unit

6.

Display module

7.

2−way valve

8.

Interior light

9.

Interior refrigerator thermistor

10.

Interior freezer thermistor

11.

Ambient temperatures thermistor

12.

LED module

N2152

1

2

3

12

4

5

6

11

10

9

8

7

9

13

1.

Main PCBA cooling unit

2.

Fuse 15A

3.

Input power 12V DC

4.

Interior Fan

5.

Fan cooling unit

6.

Display module

7.

Interior light

8.

2−way valve

9.

Interior refrigerator thermistor

10.

Interior freezer thermistor

11.

Ambient temperatures thermistor

12.

Interior light switch

N2160/N2175

1

2

3

12

4

5

6

11

10

9

7

8

14

•

Connector layout of the input power 12V DC:

8. Mounting the refrigerator

•

Mount the refrigerator in stable furniture.

•

Place the refrigerator partly into the furniture, allowing 4in [10cm] free at the top of the

refrigerator.

(RED)

(WHITE)

4 in

15

•

Connect the power connector with the 12V power connector in the vehicle.

For models N2090 and N2152:

It is advised to have the power supply in the vehicle to be routed via the roof. In this

way an over−length of cable is not needed and the power supply cable cannot block

the airways.

For models T2160 and T2175:

Connect the 12V power connector before any furniture is mounted. Make sure that the

12V cable is not trapped between the refrigerator and furniture.

•

Slide the refrigerator to the back of the furniture.

The space holders on the back will stop the fridge at correct position.

•

Use a screw suitable for below hole dimensions.

Table 4: Hole dimensions

N2090 N2152 N2160/N2175

side side floor side floor

A

Ø 0.35in

[9mm]

Ø 0.35in

[9mm]

Ø 0.35in

[9mm]

Ø 0.35in

[9mm]

Ø 0.20in

[5mm]

B

0.24in

[6mm]

0.24in

[6mm]

1.34in

[34mm]

0.24in

[6mm]

0.43in

[11mm]

C

Ø 0.16in

[4.0mm]

Ø 0.18in

[4.5mm]

Ø 0.18in

[4.5mm]

Ø 0.18in

[4.5mm]

Ø 0.20in

[5mm]

•

Fix the refrigerator in place with the screws, using the pre−drilled positions in the cabinet.

A

B

16

•

Use the white caps for finishing.

N2152

N2090

17

Ensure that the furniture paneling is able to handle the forces created by the

connection.

Do not screw into the refrigerator cabinet.

The refrigerators are prepared for flush build in.

9. Ventilation

The refrigerator performance depends on good ventilation. Ventilation for N2090 and N2152 takes

place through the front vent openings in the refrigerator. Ambient air enters through the bottom

at the front and is forced through the cooling system. Heated air is pushed away via the top vent

opening.

Ventilation for the N2160 and N2175 takes place through the integrated and insulated cooling unit

box at the bottom part of the refrigerator.

Ensure that the top and bottom vent openings are not obstructed and are able to vent

freely.

The bottom vent opening has no filter. For all models, placing a filter is not needed and

might lead to poor performance.

N2160/N2175

18

Top model

N2090

2

3

1

La page charge ...

Norcold N2090 Guide d'installation

Norcold N2090 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents