Norcold N41/ N51 Le manuel du propriétaire

Marque: Norcold

Modèle: N41/ N51

Taper: Le manuel du propriétaire

Owner’s Manual

For N41X models - 4.5 cu. ft., 2-way or 3-way, refrigerators.

For N51X models - 5.5 cu. ft., 2-way or 3-way, refrigerators.

The model numbers of 3-way refrigerators include “.3”. The model numbers of 2-way

models do not.

The letter “X” in the model number above, stands for a letter or a numeral which means a

refrigerator option.

NORCOLD, Inc.

P.O. Box 4248

Sidney, OH 45365-4248

Part No. 635480C (11/11/2020)

English

FIRE OR EXPLOSION HAZARD

If you smell gas:

1. Open Windows

2. Do not attempt to light appliance.

3. Do not touch electrical switches.

4. Extinguish any open ame

5. Shut o fuel supply.

6. Evacuate immediately and call emergency services.

Failure to follow these instructions could result in re or explosion, which could cause

property damage, personal injury, or death.

Improper installation, adjustment, alteration, service or maintenance

can cause injury or property damage. Refer to this manual. For

assistance or additional information, contact a qualied installer,

service agency, or the gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other ammable vapors and liquid in

the vicinity of this or any other appliance.

Norcold Customer Support Dept.

Telephone: 800-543-1219

Fax: 734-769-2332

Web Site: www.norcold.com

WARNING

Owner’s Manual 2

Table of Contents

For dened warranty terms, please see the one page warranty statement included in the product information packet.

Safety Awareness ..................................................................................................................................................................................... 2

Safety Instuctions .....................................................................................................................................................................................3

About Your Refrigerator ............................................................................................................................................................................ 3

Storage volume .................................................................................................................................................................................3

Leveling .............................................................................................................................................................................................3

Operation during travel ...................................................................................................................................................................... 3

Food compartment ............................................................................................................................................................................4

Flip-up shelf ....................................................................................................................................................................................... 4

Door bins ...........................................................................................................................................................................................4

Freezer compartment ........................................................................................................................................................................4

Door latch for travel and storage .......................................................................................................................................................4

Temperature control system .............................................................................................................................................................. 4

Operating the Refrigerator Controls .........................................................................................................................................................5

Control Panel ............................................................................................................................................................................................ 5

Automatic mode operation ................................................................................................................................................................5

Removing the air from the propane gas supply lines ........................................................................................................................6

Set the controls to automatic mode operation ...................................................................................................................................6

Set the controls to manual mode operation.......................................................................................................................................7

Cooling unit sensing ..........................................................................................................................................................................7

Backup operating system ..................................................................................................................................................................8

DC Operation Precautions (3-way models only) ......................................................................................................................................8

DC Operation Guidelines (3-way models only) ........................................................................................................................................9

Eects of High Altitude on Propane Gas Operation .................................................................................................................................9

Eects of Freezing Temperatures on Refrigerator Operation ................................................................................................................... 9

Refrigerator Care Checklist ......................................................................................................................................................................9

Defrosting ...............................................................................................................................................................................................10

Cleaning ................................................................................................................................................................................................. 11

Drip tray ................................................................................................................................................................................................. 11

Door Sealing ........................................................................................................................................................................................... 11

Refrigerator Maintenance Checklist .......................................................................................................................................................12

Refrigerator Storage ...............................................................................................................................................................................12

Refrigerator Maintenance .......................................................................................................................................................................13

Gas ame appearance ....................................................................................................................................................................13

Remove and clean the burner orice ..............................................................................................................................................13

Remove the Refrigerator ........................................................................................................................................................................14

Reinstall the Refrigerator ........................................................................................................................................................................ 14

Replacement Parts .................................................................................................................................................................................15

Wiring Diagram and Pictorial ..................................................................................................................................................................15

Fault Codes ............................................................................................................................................................................................16

Read this manual carefully and understand the contents before you use the refrigerator.

Be aware of possible safety hazards when you see the safety alert symbol on the refrigerator and in this manual. A signal word follows

the safety alert symbol and identies the danger of the hazard. Carefully read the descriptions of these signal words to fully know their

meanings. They are for your safety.

This signal word means a hazard, which if ignored, can cause dangerous personal injury, death, or much

property damage.

This signal word means a hazard, which if ignored, can cause small personal injury or much property

damage.

Safety Awareness

WARNING

CAUTION

Owner’s Manual 3

- The storage of ammable materials behind or around the refrigerator creates a re hazard. Do not use the area

behind the refrigerator to store anything, especially ammable materials (gasoline, cleaning supplies, etc.)

- Do not remove the round ground prong from the refrigerator AC power cord. Do not use a two prong adapter or

extension cord on the AC power cord.

- A circuit overload can result in an electrical re if the wires and/or fuses are not the correct size. Either use the wire

and fuse sizes as writtten in the “Installation Manual” or refer to your local codes or the applicable RVIA Standards

for the correct wire and fuse sizes.

- Incorrect installation, adjustment, change to, or maintenance of this refrigerator can cause personal injury, property

damage, or both. Have service and maintenance work done by your dealer or by an Norcold authorized service

center.

- Disconnect both the AC and DC power sources before doing any maintenance work on the refrigerator. All service

work on this refrigerator must be done by a qualied service technician.

- Do not bypass or change the refrigerator’s electrical components or features.

- When you discard an appliance, remove all doors to prevent accidental entrapment and suocation.

- Do not spray liquids near electrical outlets, connections, or the refrigerator components. Many liquids are electrically

conductive and can cause a shock hazard, electrical shorts, and in some cases re.

- The refrigerator cooling system is under pressure. Do not try to repair or to recharge a defective cooling system. The

cooling system contains sodium chromate. The breathing of certain chromium compounds can cause cancer. The

cooling system contents can cause severe skin and eye burns, and can ignite and burn with an intense ame. Do not

bend, drop, weld, move, drill, puncture, or hit the cooling system.

- At regular intervals, make sure that the refrigerator ue the burner, the vent areas, and the ventilation air pathway

between the vents are completely free from any ammable material or blockage. After a period of storage, it is

especially important to check these areas for any ammable material or blockage caused by animals.

- The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the

refrigerator, be careful and wear cut resistant gloves.

Safety Instructions

About Your Refrigerator

Storage Volume:

This refrigerator is made to store fresh and frozen foods and for making ice.

N41X N51X

Total capacity 4.50 cubic feet 5.50 cubic feet

Freezer capacity .81 cubic feet .81 cubic feet

Food compartment capacity 3.69 cubic feet 4.69 cubic feet

Leveling:

The refrigerator is made to operate within 3° o level side-to-side and 6° o level front-to-back (as looking at

the front of the refrigerator). Operating it at more than these limits can cause damage to the cooling system

and create a risk of personal injury or property damage. Make sure the vehicle is level before you operate

the refrigerator.

WARNING

CAUTION

Owner’s Manual 4

Operation during travel:

While the refrigerator should be level when the vehicle is stopped, performance during travel is not usually eected.

Food compartment:

Ignite or start up the refrigerator and let it cool for eight hours before loading with food. If the refrigerator does not start to cool down

after about two hours, contact your dealer or an authorized Norcold Service Center.

For the best cooling performance:

- Let air move freely inside the entire food compartment.

- Do not cover the shelves with plastic, paper, etc.

To decrease the amount of ice that collects on the cooling ns:

- Cover all liquids and moist foods.

- Let all hot foods cool before putting them in the refrigerator.

- Do not open the door any longer than necessary.

Flip-up shelf:

The ip-up shelf supplies a space to store tall bottles. To use the ip-up shelf, lift the center of the shelf and fold it up against the inside

wall of the refrigerator.

Door Bins:

You may put the door bins [52] of the fresh food compartment in a location that best meets your

need (See Art01114). To remove the bins, lift them over the locator and pull them forward. To

install the bins, push them onto the locator.

Do not wash the door bins in a dishwasher. The door bins are not dishwasher

safe.

Freezer compartment:

The freezer compartment is made to keep pre-frozen food frozen and not to quick freeze food.

Keep pre-frozen foods in the freezer compartment.

Do not put other items on the ice tray while the water is freezing. The water

freezes more rapidly if the thermostat is at the coldest temperature setting.

Door latch for travel and storage:

During travel, the door latch prevents the door from opening. There are no chains, slides, or any

devices that you must engage.

During storage, the door latch prevents the door from completely closing. Use it to

prevent odors when the refrigerator is shut down for a long period of time.

To use the door latch for storage (See Art00979):

- Open the door just so the door latch [161] is between the ribs [166] of the latch plate

[162].

Temperature control system:

Although the refrigerator is not frost -free, it is made to limit frost on the cooling ns. At

regular intervals, the temperature control system automatically melts most of the frost

from the cooling ns. The water from the cooling ns drains into a collection cup that is

attached to the back of the refrigerator. The heat of the cooling system evaporates the

water from the collection cup.

Art01114

161

166

162

Art00979

NOTICE

Owner’s Manual 5

Operating the Refrigerator Controls

Control panel:

The refrigerator control panel (see Art01562) is above the

refrigerator door. A 12 volt DC power supply is necessary for the

control functions of the refrigerator to operate. The refrigerator

receives DC power from the 12 volt system of the vehicle; either an

auxiliary battery, a converter, or the vehicle engine battery.

The ON / OFF button [30] starts and shuts down the refrigerator:

- To turn on the refrigerator, push and release the ON / OFF

button.

- To turn o the refrigerator, push the ON / OFF button for one

second and then release.

The TEMP SET button [32] controls the temperature adjustment of

the freezer and the fresh food compartment. The temperature adjustment that you select does not change if the mode of operation of

the refrigerator changes.

- Push the TEMP SET button and the temperature setting “1-9” appears in the center display [33].

- Push and hold the TEMP SET button and the temperature setting changes.

- When the desired temperature setting shows, release the TEMP SET button.

- The temperature setting shows for ten seconds and then the current operation mode of the refrigerator shows.

- The number “9” is the coldest temperature setting.

The MODE button [31] controls the operation mode of the refrigerator.

- Push and hold the MODE button and a light bar shows in the center display beside each of the four operating modes of the

refrigerator, one at a time.

- There is one automatic mode of operation and two manual modes of operation.

On 3-way models only, there are three manual modes of operation.

- When the light bar shows beside the mode of operation that you choose, release the MODE button to operate the refrigerator

in that mode.

Automatic mode operation:

When the refrigerator is in AUTO mode, it automatically uses the most ecient energy source that is available for operation. During

operation, if a more ecient energy source becomes available, the refrigerator controls change from the current energy source to the

more ecient energy source as follows:

- The rst choice is AC operation if 120 volts AC is available to the refrigerator.

- The second choice is propane gas operation if 120 volts AC is not available to the refrigerator.

- The third choice is DC operation (3-way models only) if neither 120 volts AC nor propane gas is available to the refrigerator.

Art01562

LP GAS

AUTO

1-COLD 9-COLDEST TEMP SET MODE ON/OFF

164

NOTICE

Owner’s Manual 6

Removing air from the propane gas supply lines:

For safety reasons, the burner is made to ignite on propane gas within a specied amount of time. When starting the refrigerator for

the rst time, after storage, or after replacing propane gas tank, the propane gas supply lines can have air in them. Due to the air in the

gas supply lines, the burner may not ignite on propane gas within the specied amount of time.

To remove the air from the propane gas supply lines:

- Make sure that all of the gas valves are open.

- Push the ON / OFF button to turn the refrigerator on.

- Push and hold the MODE button until the light bar beside LP GAS [36] shows.

- This means that the refrigerator is operating on propane gas.

- If the air in the propane gas supply lines prevents the burner from ignition on propane gas, the fault code “F” will appear in the

center display.

- Push and hold the ON / OFF button for one second and then release to turn the refrigerator o.

- Push the On / O button to turn the refrigeratro on.

- The refrigerator will start a 30 second trial for ignition.

- During the 30 second trial for ignition, the refrigerator controls open the gas safety valve and the igniter sparks.

- After 30 seconds, the refrigerator controls closes the gas safety valve and the igniter stops sparking.

- When the light bar beside the LP GAS shows and no fault code remains, this means that the refrigerator is operating on propane

gas.

- At this time, all of the air is removed from the propane gas supply lines and you may select AUTO mode of operation if you

wish.

- Depending on how much air may be in the propane gas supply lines, you may need to repeat the 30 second trial for ignition two or

three times.

- If the burner does not ignite on propane gas after two or three attempts, stop and consult your local dealer or an authorized

Norcold Service Center.

Set the controls to automatic mode operation:

- Push the ON / OFF button to turn the refrigerator on.

- Push and hold the MODE button until the light bar shows beside AUTO [34] and then release.

- If 120 volts AC is available to the refrigerator:

- The light bar beside AC [35] also shows in the center display.

- After ten seconds, the light bar beside AC goes o and only the light bar beside AUTO remains.

- This means that the refrigerator is operating on AC electric.

- If 120 volts AC is not available to the refrigerator:

- The light bar beside AC also shows in the center display.

- After a few seconds, the light bar beside AC goes o and the light bar beside LP GAS shows.

Owner’s Manual 7

- After 10 seconds, the light bar beside LP GAS goes o and only the light bar beside AUTO remains.

- This means that the refrigerator is operating on propane gas.

- On 2 way models only, if neither 120 volts AC nor propane gas is available to the refrigerator:

- The fault codes “F” and then “A” show in the center display.

- On 3-way models only, if neither 120 volts AC nor propane gas is available to the refrigerator:

- The refrigerator control will automatically change to DC electric operation.

DC electric operation is less ecient than AC electric and propane gas. Use DC electric operation only to maintain the

refrigerator temperature while in transit and if the other energy sources are not available. Do not use DC electric to

initially decrease the temperature of the refrigerator.

If an energy source is available to the refrigerator, but is not operating correctly:

- A fault code shows in the center display.

- The refrigerator controls try to change to a less ecient energy source.

- If a less ecient energy source is not available:

- A fault code shows in the center display.

- Refer to the “Fault Codes” section of this manual.

Set the controls to manual mode operation:

- Push the ON / OFF button to turn the refrigerator on.

- Push and hold the MODE button until the light bar shows beside AC [35] and then release.

- This means that the refrigerator is operating on AC electric.

- Push and hold the MODE button until the light bar shows beside LP GAS [36] and then release.

- This means that the refrigerator is operating on propane gas.

- Push and hold the MODE button until the light bar shows beside DC [164] and then release.

- This means that the refrigerator is operating on AC electric.

If the energy source is interrupted:

- A fault code shows in the center display.

- Refer to the “Fault Codes” section of this manual.

Cooling unit sensing:

The controls have the ability to sense the operation of the cooling unit. If the controls sense that the cooling unit has stopped cooling:

- The heat sources to the cooling unit are turned o and are locked out by the controls.

- A fault code “n” shows in the Center display.

NOTICE

Owner’s Manual 8

You can reset the controls and remove this fault code one time. To reset the controls, shut o and then start the refrigerator.

- To turn o the refrigerator, push the ON / OFF button for one second and then release.

- To turn on the refrigerator, push and release the ON / OFF button.

If you reset the controls and the fault occurs again before the refrigerator completes a full cooling cycle:

- The heat sources to the cooling unit are turned o and are locked out.

- A fault code “n” shows in the Center display.

- This time you can not reset the fault. Have the refrigerator serviced by your dealer or a Norcold authorized Service Center as soon

as possible.

Backup operating system:

This refrigerator has a backup operating system. The backup operating system allows the regerator to continue to cool if the

temperature sensor of the refrigerator should fail.

If this failure occurs:

- The refrigerator automatically changes to the backup operating system.

- When you push the TEMP SET button, the temperature setting ashes in the center display for ten seconds.

- After the temperature setting ashes, the mode of operation appears in the center dispaly.

- The backup operating system can overfreeze or thaw the contents of the freezer and the fresh food compartment.

- Make sure the temperatures of the freezer and the fresh food compartment are satisfactory.

If you open the door(s) too often, the temperatures inside the freezer and fresh food compartment do not

become stable. Allow the refrigerator to operate for about one hour after each adjustment change before you

examine the contents. The number “9” is the coldest temperature setting.

- If the temperature is too warm, push and hold the TEMP SET button to raise the temperature setting by one number.

- If the temperature is too cold, push and hold the TEMP SET button to lower the temperature setting by one number.

- Have the refrigerator serviced by your dealer or an Norcold authorized Service Center as soon as possible.

This refrigerator is made to operate on DC power while your vehicle is “in transit” and AC power or propane gas sources are not

available. Operate the refrigerator on DC power only when the vehicle engine is running.

For the refrigerator to operate correctly on DC power, the battery must be maintained in a fully charged condition.

For the battery to be fully charged at all times during refrigerator operation on DC, the vehicle engine must be running and the battery

charging system must be in good operating condition.

Keep in mind the following electrical precautions for DC operation of the refrigerator:

- Good battery condition is necessary for correct DC operation.

- The capacity of the battery charging system must be more than what is necessary for the refrigerator and other DC appliances.

- While the vehicle engine is running, make sure the voltage of the DC power supply leads at the refrigerator is more than 11.5 VDC.

DC Operation Precautions (3-way models only)

NOTICE

Owner’s Manual 9

Refrigerator Care Checklist

Your refrigerator will give you years of trouble free service if you do these simple checks every three to six months:

- Keep the food compartment and the freezer clean. See “Cleaning”.

- Defrost the refrigerator as necessary. See “Defrosting”.

- Make sure the door seals correctly. See “Door Sealing“.

DC operation is intended only to maintain the temperature of the refrigerator and its contents when they are already cool.

The DC operation is not intended for the initial start up and cooling of the refrigerator. Always use either the AC operation or propane

gas operation to initially start up and cool the refrigerator. The refrigerator must be cooled and the temperature must be steady before

you operate the refrigerator on DC.

Keep in mind the following guidelines for DC operation of the refrigerator:

- Use DC operation of the refrigerator while the vehicle is in transit.

- Do not use DC operation until the refrigerator and its contents are completely cooled.

- Only use DC operation if the vehicle battery and battery charging system are in good operating condition.

DC Operation Guidelines (3-way models only)

Eects of High Altitude on Propane Gas Operation

When you operate the refrigerator on propane gas at altitudes higher than 5500 feet above sea level:

- You may experience reduced cooling performance of the refrigerator.

- You may experience burner outages.

To avoid these possible problems, Norcold recommends that you operate the refrigerator on AC when at altitudes higher than 5500 feet

above sea level.

A gas absorption refrigerator is not designed to operate in freezing temperatures. If the refrigerator is not equipped for low temperature

operation, and if the cooling system of the refrigerator is exposed to temperatures of 32° F. or lower for an extended period of time,

the refrigerator operation may be disrupted. The refrigerator operation will resume when the cooling system of the refrigerator warms

suciently.

The refrigerator is equipped for low temperature operation. The refrigerator will operate in temperatures down to 0°F with the cold

weather kit provided if connected.

Disrupted operation of the refrigerator, due to extended exposure to temperatures of 32° F. or lower, and any costs incurred to warm the

cooling system of the refrigerator are not covered by the Norcold limited warranty. Please contact your local RV dealer for information

about how to resume refrigerator operation or about how to equip your refrigerator for operation in freezing temperatures.

Do not change the installation or the venting of your refrigerator. Refrigerator failures, which are the result of changes to either the

refrigerator installation or to the venting, are not covered by the Norcold limited warranty.

Eects of Freezing Temperatures on Refrigerator Operation

Owner’s Manual 10

Defrosting

The cooling ns of the refrigerator operate at below freezing temperature and will naturally form frost from humidity, which is always

present in the air. The humidity inside the refrigerator increases:

- with higher outside temperature and humidity.

- with the storage of non-sealed fresh foods or warm foods.

- with the amount of time that the door(s) are open.

- with any air leakage into the refrigerator.

Although the refrigerator is not frost -free, it is made to limit frost on the cooling ns. At regular intervals, the temperature control system

automatically melts most of the frost from the cooling ns. The water from the cooling ns drains into a collection cup that is attached to

the back of the refrigerator. The heat of the cooling system evaporates the water from the collection cup.

It is normal for frost to collect inside the freezer. Excess frost decreases the cooling performance of the refrigerator. Defrost the

refrigerator and freezer as necessary:

- Remove all food from the refrigerator.

- Turn the refrigerator OFF.

Defrosting the refrigerator makes excess water inside the refrigerator.

- Remove the drain hose from the drip cup at the rear of the refrigerator.

- Put the drain hose into a half-gallon or larger container to capture water.

- Put dry towels (etc.) inside the refrigerator and freezer to absorb melted frost.

High temperatures can cause the inside surfaces of the refrigerator to warp or melt. Do not use pans of

HOT water, a hair dryer, or any other high temperature devices to defrost the refrigerator. Do not use any

hard or sharp objects to remove frost. Damage to the interior of the refrigerator can occur.

- To increase the speed of defrosting, put pans of WARM water in the refrigerator and freezer.

- Remove the wet towels (etc.) and dry the interior.

- Remove the drain hose from the large container and put the drain hose back into the drip cup.

- Remove the large container from the enclosure.

- Start up the refrigerator.

- Allow the refrigerator to cool down.

- Return all food to the refrigerator.

- Be aware of any cooling changes that are not because of weather, loading, or gas control changes. If changes occur, contact your

dealer or an authorized Norcold Service Center.

- Make sure the gas supply is propane gas only and not butane or a butane mixture.

CAUTION

NOTICE

Owner’s Manual 11

A good time to clean the refrigerator is just after you defrost it.

Clean the inside of the refrigerator as often as necessary to avoid food odors:

- Remove all food from the refrigerator.

Do not use abrasive cleaners, chemicals, or scouring pads because they can damage the interior of the refrigerator.

- Wash the interior with a solution of liquid dish detergent and warm water.

- Rinse with a solution of baking soda and clean water.

- Dry with a clean cloth.

- Put all food in the refrigerator.

Drip tray:

To remove and clean the drip tray:

- Locate the plastic clip that is around the wire shelf in front of the drip tray.

- Remove and save the screw that attaches the plastic clip to the inside of the refrigerator cabinet.

- Pull the self forward to remove from the refrigerator

- Make sure that the drip tray is empty of water.

- Pull the drain tube plug out from the inside of the drip tray and out of the drain hose.

- Pull the drip tray forward to remove from the slots in the refrigerator cabinet.

- Clean the drip tray.

- Put the drain tube plug down into the drip tray and push the drip tray back into the original position.

- Push the drain hose back onto the drain tube plug.

- Put the wire shelf and plastic clip back in the original position.

- Attach the plastic clip with the screw.

Cleaning

Door Sealing

If the door does not seal correctly, excess frost will collect inside the refrigerator. Make sure the door seals correctly:

- Close the door on a piece of paper that is about the size and thickness of a dollar bill (See

Art00980).

- Gently pull the paper.

- You should feel a slight drag between the gasket and the cabinet.

- Do this on all four sides of the door.

Art00980

NOTICE

Owner’s Manual 12

Refrigerator Storage

Before the refrigerator is stored for an extended (seasonal) period of time:

- Defrost and clean the interior of the refrigerator.

- Close the doors with the storage latch.

If the refrigerator is stored for an extended period of time, before start up:

- Make sure there are no obstructions in the vents, the ventilation air pathway, the burner, the orice, or the ue area.

Refrigerator Maintenance Checklist

Read and understand the following maintenance sections of this manual.

Norcold is not responsible for installation, adjustment, alteration, service, or maintenance performed by anyone other

than a qualied RV dealer or an authorized Norcold Service center.

Have a qualied RV dealer or an authorized Norcold Service Center do these annual safety and maintenance checks:

- Examine the gas supply lines for leaks.

- Replace or repair if necessary.

- Make sure the propane gas pressure is 11 inches of water column.

- Adjust if necessary.

- Make sure the combustion seal is complete and intact.

- Replace or repair it if necessary.

- Make sure the burner and the burner orice are clean (See Art00956).

- Clean if necessary.

- Make sure the electrode spark gap [167] is 1/8 - 3/16 inch (See Art00955).

- Adjust if necessary.

- Make sure the AC voltage is 108 - 132 volts and the DC voltage is 10.5 - 15.4 volts.

- Make sure the thermocouple tip is clean and secure.

- Make sure the area at the rear of the refrigerator is free of any combustible materials,

gasoline, and other ammable vapors and liquids.

- If you do not feel a slight drag on the paper, the door is not sealing correctly:

- Make sure the screws of the hinges are tight.

- Make sure the door gasket does not touch the door latch:

- If the door gasket touches the door latch, loosen the screws of the door latch.

- Raise the door latch just so it does not touch and tighten the screws of the door latch.

- Make sure the door latch holds the door closed.

Art00955

167

Art 00956

NOTICE

Owner’s Manual 13

Refrigerator Maintenance

Gas ame appearance:

While in propane gas operation, examine the appearance of the gas ame:

- Push and hold temperature setting button until the “9” shows and then release.

- Open the lower intake vent.

The burner box cover can be hot. Wear gloves to avoid burns.

- Open the burner box door [165] and look at the gas ame [75] (See Art00955 and

Art00975).

- The ame should be:

- a darker blue color on the inside of the ame and a lighter blue color on

the outside of the ame.

- a constant shape without ickering.

- Contact your dealer or Norcold authorized service center if the ame is:

- yellow

- ickering or changing shape.

- Make sure the ame does not touch the inside of the ue tube [76].

- If the ame touches the inside of the ue tube, contact your dealer or an authorized Norcold Service Center.

- Close the burner box door.

Remove and clean the burner orice:

Your dealer or an authorized Norcold Service Center must do this procedure.

To remove and clean the burner orice:

- Close the valve at the propane gas tank(s).

- Close the manual shut o valve of the refrigerator.

- Shut down the refrigerator..

- Open the lower intake vent.

The burner box cover can be hot. Wear gloves to avoid burns.

- Remove the burner box cover by removing one screw.

To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the gas supply line

at the refrigerator’s manual shut o valve.

- Remove the are nut from the orice assembly [77] (See Art00956).

- Remove the orice assembly from the burner [78].

Do not try to remove the orice [79] from the orice adapter [80] when cleaning. Removal will damage

the orice and seal of the orice and can cause a propane gas leak. Leaking propane gas can ignite or

explode which can result in dangerous personal injury or death. Do not clean the orice with a pin or

other objects.

Art00975

165

CAUTION

WARNING

NOTICE

Owner’s Manual 14

Remove the Refrigerator

Your dealer or an authorized Norcold Service Center must do this procedure.

The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the

refrigerator, be careful and wear cut resistant gloves.

1. Close the valve at the propane gas tank(s).

To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the gas supply line

at the refrigerator’s manual shut o valve.

2. Open the lower intake vent and remove the gas supply line from the manual shut o valve of the refrigerator.

3. Remove the AC power cord from the receptacle.

4. Remove the DC wiring from the refrigerator:

- Remove the DC wiring from the battery or the converter of the vehicle.

- Put a mark on the DC wires so you can put them back in the correct location.

- Remove the DC wires from the refrigerator.5. Remove the screws which fasten the refrigerator to the oor.

6. Remove the door from the refrigerator.

7. Remove the screws which fasten the refrigerator to the wall.

8. Remove the refrigerator from the opening.

9. Attach the door to the refrigerator.

- Clean the orice assembly with air pressure and alcohol only.

- Using a wrench, assemble the orice assembly to the burner.

- Assemble the are nut to the orice assembly.

- Tighten the are nut by hand.

- Hold the orice assembly securely and, using a wrench, tighten the are nut 1/4 revolution only.

- Examine all of the connections for gas leaks.

Reinstall the Refrigerator

Your dealer or an authorized Norcold Service Center must do this procedure.

Make sure the combustion seal is not broken, is completely around the refrigerator mounting anges, and

is between the mounting anges and the wall of the enclosure. If the combustion seal is not complete,

exhaust fumes can be present in the living area of the vehicle. The breathing of exhaust fumes can cause

dizziness, nausea, and in extreme cases, death.

1. Push the refrigerator completely into the enclosure.

2. Remove the door from the refrigerator.

NOTICE

CAUTION

WARNING

NOTICE

Owner’s Manual 15

3. Put the screws though the mounting anges and into the wall.

4. Attach the door to the refrigerator

The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the

refrigerator, be careful and wear cut resistant gloves.

5. Open the lower intake vent and put the screws through refrigerator and into the oor.

To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the gas supply line at

the refrigerator’s manual shut o valve.

6. Attach the gas supply line to the manual shut o valve of the refrigerator.

7. Open the valve at the propane gas tank(s).

Do not allow the leak checking solution to touch the electrical components. Many liquids are electrically

conductive and can cause a shock hazard,electrical shorts, and in some cases re.

8. Examine the gas supply line for leaks.

9. Connect the DC wiring to the refrigerator:

- Install the DC fuse or connect the DC wiring to the battery or the converter.

- Connect the DC wires from the refrigerator.

10. Connect the AC power cord to the receptacle.

Replacement Parts

You may purchase replacement parts through your local RV dealer or an authorized Norcold Service Center.

Wiring Diagram and Pictorial

The parts of the wiring diagram are (See Art01775):

The parts of the wiring pictorial are (See Art01776):

AC heater .................................................................................................................................................................................................A

Thermister ............................................................................................................................................................................................... B

Gas valve................................................................................................................................................................................................. C

Igniter....................................................................................................................................................................................................... D

Temperature switch (optional) ................................................................................................................................................................. E

Fan (optional) ...........................................................................................................................................................................................F

DC heater (optinal) ..................................................................................................................................................................................G

Chassis ground........................................................................................................................................................................................ H

DC board (optional) ..................................................................................................................................................................................I

Switched 12 VDC .....................................................................................................................................................................................1

Fused continuous 12 VDC........................................................................................................................................................................2

Communications ....................................................................................................................................................................................... 3

Display ground..........................................................................................................................................................................................4

Auxiliary ground (optional) ........................................................................................................................................................................ 5

Auxiliary +12 VDC (optional) ....................................................................................................................................................................6

Gas valve +12 VDC .................................................................................................................................................................................. 7

5 A Fuse DC ...........................................................................................................................................................................................F1

8A Fuse AC.............................................................................................................................................................................................F2

30 A Fuse DC .........................................................................................................................................................................................F3

WARNING

CAUTION

Owner’s Manual 16

Art01775

GND

12VDC

AC_HT_HI2

BK/NR

AC_HT_LO

120 VAC

120 VCA

}

TEMP

- 12 VDC/VCD

+ 12 VDC/VCD

WH/BC

POWER BOARD / PANNEAU D’ALIMENTATION

ON-OFF

OVERLAY/REVÊTRMENT

MODE

DISPLAY BOARD/CARTE D’AFFICHAGE

8 AMP

AC_HT_LO2

AC_HT_HI

LIMIT_IN

LIMIT_OUT

WH/BC

YL-GN-/JN-VE

WH/BC

5 AMP

BK/NR

RD/RG

BU/BL

WH-VT/BC-VT

GN/VE

BK/NR

WH-RD/BC-RG

RD/RG

BK/NR

GND

12VDC

HTR_GND

DC_HTR

30 AMP

BK/NR

RD/RG

YL/JN

WH/BC

BK/NR

A AC HEATER / ÉLÉMENT CHAUFFANT CA

B THERMISTOR / THERMISTANCE

C GAS VALVE / ROBINET DE GAZ

D IGNITER / ALLUMEUR

E TEMPERATURE SWITCH / INTERRUPTRUR DE TEMPÉRATURE

F FAN / VENTILATEUR

G DC HEATER / ÉLÉMENT CHAUFFANT CD

H CHASSIS GROUND / MASSE DU CHASSIS

I DC BOARD / PANNEAU CD

- OPTIONAL

/ FACULTATIF

1 SWITCHED 12VDC / COMMUTÉ 12VCD

2 FUSED CONTINUOUS 12VDC/ CONTINU

FONDU 12VCD

3 COMMUNICATIONS / COMMUNICATIONS

4 DISPLAY GROUND / AFFICHAGE LA TERRE

5 AUXILIARY GROUND / MASSE AUXILIAIRE

6 AUXILIARY +12VDC / AUXILIAIRE +12VCD

7 GAS VALVE +12VDC / ROBINET DE GAZ +12VCD

F1 5 AMP DC FUSE / FUSIBLE DE 5 AMPERES CD

F2 8 AMP AC FUSE / FUSIBLE DE 5 AMPERES CA

F1 30 AMP DC FUSE / FUSIBLE DE 30 AMPERES CD

Art01776

OVERLAY/REVÊTRMENT

DISPLAY BOARD/

CARTE D’AFFICHAGE

POWER BOARD/ PANNEAU D’ALIMENTATION

+12VDC/VCD

5 AMP

AC_HT_HI

LIMIT_IN

LIMIT_OUT

AC_HT_LO

AC_HT_HI

AC_HT_LO

GND

12VDC

-12VDC/VCD

6 1

GND

12V

HTR_GND

DC_HTR

30 AMP

8 AMP

A AC HEATER / ÉLÉMENT CHAUFFANT CA

B THERMISTOR / THERMISTANCE

C GAS VALVE / ROBINET DE GAZ

D IGNITER / ALLUMEUR

E TEMPERATURE SWITCH / INTERRUPTRUR DE TEMPÉRATURE

F FAN / VENTILATEUR

G DC HEATER / ÉLÉMENT CHAUFFANT CD

H CHASSIS GROUND / MASSE DU CHASSIS

I DC BOARD / PANNEAU CD

- OPTIONAL

/ FACULTATIF

F1 5 AMP DC FUSE / FUSIBLE DE 5 AMPERES CD

F2 8 AMP AC FUSE / FUSIBLE DE 5 AMPERES CA

F1 30 AMP DC

FUSE / FUSIBLE DE 30 AMPERES CD

Owner’s Manual 17

Fault Codes

Corrective Actions

Check:

- That the refrigerator is ON.

- That the battery charging equipment of the vehicle is operational.

- The the AC/DC converter is operational (if applicable).

- See your dealer or authorized Norcold Service Center.

Check:

- That the valve of the propane gas tank(s) is open.

- That the propane gas is at the correct pressure.

- That the manual shut o valve of the refrigerator is open.

- That there is no air in the propane gas supply line. See “Removing air

from the propane gas supply lines” section of this manual.

Check:

- That the refrigerator is plugged into a serviceable outlet.

- That the fuse or circuit breaker is intact.

- That the vehicle generator is operational (if applicable).

- See your dealer or authorized Norcold Service Center.

Check:

- That the battery charging equipment of the vehicle is operational.

- The the AC/DC converter is operational (if applicable).

- See your dealer or authorized Norcold Service Center.

1st time - Before reset

Check:

- That the vents are not blocked.

- That a door(s) is not open. Close door(s).

- That the vehicle is level.

2nd time - After reset.