Aurora Design BT-2 User's Operation Manual

Marque: Aurora Design

Modèle: BT-2

Taper: User's Operation Manual

Note: seek-button refers to the Wonderbar or Town & Country button on a

signal seeking radio. In AM/FM mode this button will only control the

radio seek function, not the Bluetooth/USB.

Bluetooth® is a registered trademark of the Bluetooth SIG

AAC trademark used under license from Via Licensing

All other trademarks are those of their respective owners

Aurora Design

BT-2

Bluetooth/AAC Adapter

User Operation

Manual

Under Industry Canada regulations, this radio transmitter may only

operate using an antenna of a type and maximum (or lesser) gain approved

for the transmitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its gain should be so

chosen that the equivalent isotropically radiated power (e.i.r.p.) is not

more than that necessary for successful communication.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d'en compromettre le fonctionnement.

Conformément à la réglementation d'Industrie Canada, le présent émetteur

radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou

inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de

réduire les risques de brouillage radioélectrique à l'intention des autres

utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la

puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité

nécessaire à l'établissement d'une communication satisfaisante.

Speciﬁcations:

Bluetooth Transceiver*:

Frequency Band:! 2.40-2.48GHz

Standard:! Bluetooth 4.1, Class 2

Proﬁles:! HFP 1.6, A2DP 1.2, AVRCP 1.5

Sensitivity:! -90dBm @ 0.1% BER

TX Power:! 4dBm maximum

Environmental:

Temperature:! -30C to 65C (-22F to 150F) Operating

! -40C to 125C (-40F to 257F) Storage

Humidity:! 10% to 90% non-condensing

Aurora Design LLC. does not assume any responsibility for personal

injury or property damage incurred due to hazardous driving as a result of

interaction with the BT-2 or other Bluetooth devices.

BE SAFE! Never text while driving or be distracted by the radio.

*Characterized by component manufacturer

Bluetooth® is a registered trademark of the Bluetooth SIG

AAC trademark used under license from Via Licensing

!! 6

Troubleshooting:

Poor Range: Make sure nothing is obstructing the dial face of the radio,

or the openings along the bottom side of the radio chassis. Try moving

your Bluetooth device to a different location.

No Sound: Make sure the BT-2 is paired and connected to your device.

Also make sure the BT-2 is selected as the audio device for streaming

audio and hands-free operation on your device following the

manufacturers instructions. Verify the audio levels are set properly on

the Bluetooth device.

US Certiﬁcation:

FCC ID: A8TBM20SPKXYNBZ

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy, and if not installed and used in

accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Consult the dealer or an experienced radio/TV technician for help.

European Certiﬁcation:

The Bluetooth module used in this device complies with the essential

requirements of the R&TTE 1999/EC, the EMC Directive 2004/108/EC

and the low-voltage Directive 2006/95/EC.

Canadian Certiﬁcation:

IC: 12246A-BM20SPKS1

This device complies with Industry Canada license-exempt RS

standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation

of the device.

Congratulations on your new Aurora Design BT-2 Bluetooth/AAC

adapter. Combined with an FMR-2 converted radio, you can enjoy 21

century technology in your classic vehicle!

Setup: Your radio may have come equipped with an internal

microphone. If not, before installing your radio back into your vehicle,

you may wish to plug the hands-free microphone or optional illuminated

pushbutton into the appropriate jacks on the radio. The microphone can be

placed in a convenient location in the vehicle, typically along the front

edge of the headliner near the rear view mirror or along the bottom edge of

the dashboard. The attached cable is 9.8’ (3M) long and can be routed as

required, typically behind the A pillar cover for headliner mounting.

Excess cable can be coiled and tied off.

The optional pushbutton assembly is not required when used with an

FMR-2 converted radio as the existing radio controls can be used to fully

control the BT-2. The pushbutton assembly can still be used with an

FMR-2 converted radio if desired, and must be used with all other

installations. The pushbutton requires a 1/2” (12.7mm) hole and should be

mounted somewhere convenient such as the bottom edge of the dashboard.

The pushbutton is illuminated with a red status LED that should be made

visible for easiest operation. The attached cable is 3.3’ (1M) long and can

be routed as required. Excess cable can be coiled and tied off.

Basic Operation: Operation of the BT-2 is extremely simple yet

powerful. The BT-2, when combined with an FMR-2 AM/FM receiver

form a fully integrated AM/FM/Bluetooth/AAC solution. Communication

over a proprietary com-link keeps the two modules in perfect sync. No

external cables, plugs or switches are required. Full operation is provided

by the existing controls on the radio. When streaming music or handling a

phone call, the FMR-2 status LED will change color to indicate Bluetooth

operation. (see FMR-2 manual for more information on status LED) When

you stop streaming music or end a call, the BT-2 will put the FMR-2 back

into normal operation. Everything is handled automatically.

The BT-2 supports SBC and AAC formats over Bluetooth. AAC ﬁles

offer higher quality and is the native format used by iTunes® and many

other popular music services. ACC ﬁles will play natively off compatible

Bluetooth devices.

The BT-2 will always return to the last mode it was in when the radio

was turned off assuming the Bluetooth device is still present. For example,

if the BT-2 was playing back from the Bluetooth when the radio was

powered off, it will return to playing back from where it left off when the

radio is turned back on.

The BT-2 supports Voice Assist which will speak messages to you in

English, Spanish or French to assist in the operation of the radio.

Bluetooth Pairing: To pair a new device, twist the volume control

back and forth twice towards the direction of higher volume. (this is the

!5! 2

same action that is used with the tone control to access the virtual fader

function) or push and hold the optional pushbutton. The optional front

panel status LED or the optional pushbutton LED will ﬂash and a Voice

Assist message will be heard in the radio. The BT-2 will then go into

pairing mode for approximately 90 seconds or until a device is paired.

While in pairing, the BT-2 will display as AuroraDesign BT-x.x in the

Bluetooth section of your device. (x.x represents the version) Select the

BT-2 to connect. (refer to the owners manual for your Bluetooth device for

information on pairing) If you wait longer than 90 seconds the BT-2 will

time out and Voice Assist message will be heard. Up to eight devices can

be paired to the BT-2.

Bluetooth Connecting: The BT-2 will automatically attempt to

reconnect to the last connected Bluetooth device. If this device is not

within range, the BT-2 will then attempt to reconnect to any of the last four

connected devices. This is handy when the user has multiple Bluetooth

devices, or several people use the radio. If any paired device is within

range when the radio is powered on, the BT-2 will reconnect and return to

its last mode. The optional front panel LED or the optional pushbutton

LED will illuminate to signify a Bluetooth device is connected. A Voice

Assist message will also be heard in the radio when a Bluetooth device

successfully connects.

Bluetooth Audio Levels: The BT-2 sends commands to the

connected Bluetooth device to adjust the playback audio levels, but many

devices require that the user make these settings manually. Usually the

playback levels for audio streaming, phone calls and Voice Command are

all stored separately so must be adjusted separately. The ﬁrst time you

stream audio, take a phone call, or use the Voice Command feature, use the

volume buttons or volume slider menu on the device to adjust the audio

level. This only needs to be performed once on the device as these settings

are permanently saved in the device.

Bluetooth Voice Command: The Bluetooth Voice Command feature

allows the user to control their compatible Bluetooth device through voice

commands. The Voice Command feature is accessible in all radio modes. It

is designed to work with Apple Siri

, Google Voice

and Microsoft

Cortana

and other Bluetooth voice interfaces. To initiate a Voice

Command, twist the volume control back and forth twice towards the

direction of higher volume or push and hold the optional pushbutton/seek-

button. (this is the same motion that was used to open up pairing) Wait for

the conﬁrmation tone from the Bluetooth device and then speak the

command. For example you can say things like “call home” or “play

Bruce Springsteen”. Check with the manual for your Bluetooth device for

further information on its support for voice commands.

Bluetooth Streaming: To start playing music from the Bluetooth

interface, twist the volume control back and forth twice towards the

direction of lower volume or push and hold the optional pushbutton/seek-

button for about 1 second. (you can also use the menus on your Bluetooth

device to control the audio) To toggle between pause and play, repeat the

procedure above. When the audio is paused, the FMR-2 status LED will

blink slowly. If the audio is paused for more than about 10 seconds, the BT-2

will release the FMR-2 and it will switch back to normal radio operation. If

playback is started again, it will continue from where it left off.

To skip to the next song, twist the tuning control towards the high

frequency end of the dial or quickly press the optional pushbutton/seek-

button once. To skip to the previous song, twist the tuning control towards

the low frequency end of the dial or quickly press the optional pushbutton/

seek-button twice. (Hint: when twisting the tuning control, twist it in the

desired direction and then back to the starting point. This way the tuner

always remains in the same position)

Hands-free Phone: When a phone call comes in, the FMR-2 will

mute the radio and ring through. To accept the call, twist the tuning control

towards the high frequency end of the dial or quickly press the optional

pushbutton/seek-button once. To reject or end a call, twist the tuning

control towards the low frequency end of the dial or quickly press the

optional pushbutton/seek-button twice or press the seek button again.

To mute the microphone, twist the volume control back and forth

twice towards the direction of lower volume or push and hold the optional

pushbutton/seek-button for about 1 second. (you can also use the menus

on your Bluetooth device to control the audio) A repeating conﬁrmation

tone will be heard on the radio while the call is muted. To toggle between

mute and unmuted, repeat the instructions above. When the audio is

muted, the FMR-2 status LED will blink slowly. A Voice Assist message

will be heard conﬁrming when the call ends.

For call-waiting, follow the same procedure as above to accept or

reject the waiting call. To switch between calls, use the accept call action.

To end the active call, use the reject call action. To join the calls, twist the

volume control back and forth twice towards the direction of higher

volume or push and hold the optional pushbutton/seek-button.

Note: The Bluetooth device can also be controlled using its own menus.

(follow manufactures instructions on controlling your device)

Voice Assist Language: The BT-2 can speak to you in English,

Spanish, French and simple beep tones. To select the desired language

make sure no Bluetooth device is connected to the BT-2. Now enable

Pairing as described above. After you hear the Voice Assist message, enter

Pairing again. The next language set will be heard. Continue entering

Pairing until the desired language is selected. All Voice Assist messages

will now be in the selected language.

!3! 4

Aurora Design BT-2 User's Operation Manual

Marque: Aurora Design

Modèle: BT-2

Taper: User's Operation Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Aurora Design BT-2

Documents connexes

Aurora Design BT-2.5 User's Operation Manual

Aurora Design BT-2 User's Operation Manual

Aurora Design BT-2 User's Operation Manual

dans d''autres langues

Documents connexes

Autres documents