Sony MDS-S707 Mode d'emploi

1

EN

 1998 by Sony Corporation

3-862-832-11(1)

MDS-S707

MiniDisc Deck

Operating Instructions

Mode d’emploi

GB

EN

F

S

2

EN

This symbol is intended to

alert the user to the presence

of important operating and

maintenance (servicing)

instructions in the literature

accompanying the appliance.

INFORMATION

This equipment has been tested and

found to comply with the limits for a

Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are

designed to provide reasonable

protection against harmful interference

in a residential installation. This

equipment generates, uses, and can

radiate radio frequency energy and, if

not installed and used in accordance

with the instructions, may cause

harmful interference to radio

communications.

However, there is no guarantee that

interference will not occur in a

particular installation. If this equipment

does cause harmful interference to radio

or television reception, which can be

determined by turning the equipment

off and on, the user is encouraged to try

to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet

on a circuit different from that to

which the receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

CAUTION

You are cautioned that any changes or

modification not expressly approved in

this manual could void your authority

to operate this equipment.

Owner’s Record

The model and serial numbers are

located on the rear of the unit.

Record the serial number in the space

provided below. Refer to them

whenever you call upon your Sony

dealer regarding this product.

Model No. MDS-S707

Serial No.

WARNING

To prevent fire or shock

hazard, do not expose the unit

to rain or moisture.

To avoid electrical shock, do

not open the cabinet. Refer

servicing to qualified

personnel only.

The laser component in this product is

capable of emitting radiation exceeding

the limit for Class 1.

This appliance is classified as a CLASS 1

LASER product. The CLASS 1 LASER

PRODUCT MARKING is located on the

rear exterior.

The following caution label is located

inside the unit.

For the customers in US

This symbol is intended to

alert the user to the presence

of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of

sufficient magnitude to

constitute a risk of electric

shock to persons.

For the customers in Canada

CAUTION

TO PREVENT ELECTRIC SHOCK, DO

NOT USE THIS POLARIZED AC PLUG

WITH AN EXTENSION CORD,

RECEPTACLE OR OTHER OUTLET

UNLESS THE BLADES CAN BE FULLY

INSERTED TO PREVENT BLADE

EXPOSURE.

IN NO EVENT SHALL SELLER BE

LIABLE FOR ANY DIRECT,

INCIDENTAL OR

CONSEQUENTIAL DAMAGES OF

ANY NATURE, OR LOSSES OR

EXPENSES RESULTING FROM

ANY DEFECTIVE PRODUCT OR

THE USE OF ANY PRODUCT.

Precautions

On safety

• The use of optical instruments with

this product will increase eye hazard.

• Should any solid object or liquid fall

into the cabinet, unplug the deck and

have it checked by qualified

personnel before operating it any

further.

On power sources

• Before operating the deck, check that

the operating voltage of the deck is

identical with your local power

supply. The operating voltage is

indicated on the nameplate at the rear

of the deck.

• If you are not going to use the deck

for a long time, be sure to disconnect

the deck from the wall outlet. To

disconnect the AC power cord, grasp

the plug itself; never pull the cord.

• The mains switch is located on the

rear exterior.

• AC power cord must be changed only

at the qualified service shop.

On placement (only on models

supplied with a MAIN POWER switch)

Do not install the appliance in a

confined space, such as a bookcase or

built-in cabinet because the mains

power switch (MAIN POWER) is

located on the rear exterior.

3

EN

TABLE OF CONTENTS

Getting Started

Hooking Up the System........................................................................... 4

Connecting Optional AV Components ................................................. 5

Recording on an MD................................................................................ 6

Playing an MD.................................................................................... 8

Recording on MDs

Notes on Recording ................................................................................. 9

Useful Tips for Recording ...................................................................... 9

Recording Over Existing Tracks ...........................................................11

Adjusting the Recording Level..............................................................11

Marking Track Numbers while Recording (Track Marking)........... 12

Starting Recording with 6 Seconds of Prestored Audio Data

(Time Machine Recording)..................................................................... 13

Synchro-Recording a CD ........................................................................ 14

Synchro-Recording a Tape and Radio Program................................. 15

Recording on an MD Using a Timer ....................................................15

Playing MDs

Using the Display .................................................................................... 17

Locating a Specific Track ........................................................................18

Locating a Particular Point in a Track.................................................. 19

Playing Tracks Repeatedly..................................................................... 20

Playing in Random Order (Shuffle Play).............................................20

Creating Your Own Program (Program Play) .................................... 21

Playing an MD Using a Timer ............................................................... 22

Editing Recorded MDs

Notes on Editing ...................................................................................... 23

Erasing Recordings (Erase Function) ................................................... 23

Erasing a Portion of a Track (A-B Erase Function) ............................24

Dividing Recorded Tracks (Divide Function) .................................... 25

Combining Recorded Tracks (Combine Function) ............................26

Moving Recorded Tracks (Move Function) ........................................27

Labeling Recordings (Title Function)................................................... 28

Undoing the Last Edit (Undo Function) ..............................................30

Additional Information

Display Messages .................................................................................... 31

System Limitations .................................................................................. 31

Troubleshooting ....................................................................................... 32

Specifications ............................................................................................ 33

Guide to the Serial Copy Management System.................................. 34

Index ................................................................................................................ 35

On operation

If the deck is brought directly from a

cold to a warm location, or is placed in a

very damp room, moisture may

condense on the lenses inside the deck.

Should this occur, the deck may not

operate properly. In this case, remove

the MD and leave the deck turned on for

about an hour until the moisture

evaporates.

On the MiniDisc cartridge

• Do not open the shutter to expose the

MD.

• Do not place the cartridge where it

will be subject to extremes of sunlight,

temperature, moisture or dust.

On cleaning

Clean the cabinet, panel and controls

with a soft cloth slightly moistened with

a mild detergent solution. Do not use

any type of abrasive pad, scouring

powder or solvent such as alcohol or

benzine.

If you have any questions or problems

concerning your deck, please consult

your nearest Sony dealer.

Welcome!

Thank you for purchasing the Sony

MiniDisc Deck. Before operating the

deck, please read this manual

thoroughly and retain it for future

reference.

About This Manual

Conventions

• Controls in the instructions are those

on the deck; these may, however, be

substituted by controls on the remote

that are similarly named or, when

different, appear in the instructions

within brackets.

• The following icons are used in this

manual:

Z

Indicates a procedure that

requires use of the remote.

z

Indicates tips for making the

task easier and hints.

EN

Getting Started

4

EN

MAIN POWER

ONOFF

MAIN

POWER

Getting Started

Hooking Up the System

Connect the supplied cords (1 and 2) as described

below.

1 Connect the audio connecting cords.

Make sure to match the color of the plugs and the

connectors. Be sure to make connections firmly to

prevent hum and noise.

2 Connect the optical cable.

Take the caps off the connectors and then insert

the plugs until they click into place.

Connecting the AC power cord

Connect the AC power cord to a wall outlet or to the

outlet of a timer.

Turning on the unit (only on models

supplied with a MAIN POWER switch)

Set MAIN POWER on the rear of the unit to ON.

The unit is turned on in standby mode.

L I N E

(ANALOG)

D I G I T A L

IN

OUT

L

R

IN

OUT

1

2

MD / VIDEO

(AUDIO)

ANTENNA

SUPER WOOFER

CD DIGITAL OUT

OPTICAL

IN

OUT

L

R

L

R

SPEAKER

L

R

+–

Getting Started

5

EN

Connecting Optional AV

Components

You can connect a digital components (such as a DAT

deck or another MD deck) for digital recording. Refer

to the instructions of the component for details

regarding its operation.

Connect the digital component using the optical cable.

Take the caps off the connectors and then insert the

plugs until they click into place.

A built-in sampling rate converter automatically

converts the sampling frequency of various digital

sources to the 44.1 kHz sampling rate of your MD

deck.

This allows you to record sources such as 32- and 48-

kHz DAT or satellite broadcasts, as well as compact

discs and other MDs.

Note

When recording through the DIGITAL IN connector, you

cannot adjust the recording level.

To the DIGITAL IN connector of the component

L I N E

(ANALOG)

D I G I T A L

IN

OUT

L

R

IN

OUT

Basic Operations

6

EN

MONO

4

Set INPUT to the corresponding input connector.

5

Set REC MODE to the mode you want to record in.

Recording on an MD

Basic Operations

With the arrow

pointing this way

With the label side up

If the MD has a recorded material on it, the deck will

automatically start recording from the end of the last recorded

track.

To record through Set INPUT to

LINE (ANALOG) IN

DIGITAL

ANALOG

DIGITAL IN

To record in Set REC MODE*

1

to

Monaural sound*

2

STEREO

Stereo sound

*

1

If you switch REC MODE during recording or recording pause, recording

stops.

*

2

In the monaural recording, you can record about two times longer than in

the stereo recording.

Monitor audio during recording

Even if you set REC MODE to

MONO, the monitor signal does

not become monaural.

1

Turn on the Mini System and play the program source you

want to record.

2

Press .

The STANDBY indicator turns off.

3

Insert a recordable MD.

•

REC LEVEL

(ANALOG)

AMS

PUSH ENTER

0

10

p

·∏

•

REC MODE

INPUT

EDIT/NO YES

STEREO

MONO

ANALOG

REPEAT

DISPLAY/CHAR

SCROLL

PLAY MODE

TIMER

PHONES

LEVEL

REC OFF PLAY

MIN

MAX

r

)

0

§

=

+



DIGITAL

STANDBY

32 68

457

Basic Operations

7

EN

6

Press r.

The deck becomes ready to record.

7

When recording the analog input signal, adjust the recording

level with REC LEVEL.

The fourth dot is satisfactory for most purposes. For details,

refer to “Adjusting the Recording Level” on page 11.

8

Press ﬂ (or MD ·).

Recording starts.

9

Start playing the program source.

Do not disconnect the deck from the power source immediately after

recording

If you do, recorded material may not be saved to the MD. To save the material,

after recording, press § to take out the MD or change the deck to standby by

pressing

. “TOC” will flash in the display at this time.

After “TOC” stops flashing and goes out, you can pull out the AC power

cord.

To

Press

Stop recording

Pause recording* ﬂ (or MD P). Press the button again to

resume recording.

p

Take out the MD § after stopping recording

* Whenever you pause recording, the track number increases by one. For example, if

you paused recording while recording on track 4, the track number increases by

one and recording continues on the new track when restarted.

To protect an MD against accidental erasure

To make it impossible to record on an MD, slide the tab in the direction of

arrow, opening the slot. To allow recording, close the slot.

Rear of the disc

Slide the tab in

the direction of arrow

Record-protect tab

Note

If “Din Unlock” or “Cannot Copy”

appears in the display, recording

through the digital connector is

not possible.

In this case, record the program

source through the LINE

(ANALOG) IN jacks with INPUT

set to ANALOG.

When ”TOC“ flashes in the

display

The deck is currently updating the

Table Of Contents (TOC).

Do not move the deck or pull out

the AC power cord. Changes to an

MD made through recording are

saved only when you update the

TOC by ejecting the MD or

changing the deck to standby by

pressing .

Basic Operations

8

EN

4

Press ﬂ(or MD ·).

The deck starts playing. Adjust the volume on the amplifier.

Playing an MD

You can locate and play back

a track while the deck is

stopped

1 Turn AMS (or press MD

= or MD +) until the

number of the track you

want to play appears.

2 Press AMS or ﬂ (or

MD ·).

To use headphones

Connect them to PHONES

jack. Use PHONES LEVEL to

adjust the volume.

Adjust the

headphone

volume.

Connect the

headphones.

Pause playing

Stop playing

Do the following:

Press p.

Press ﬂ (or MD P). Press the button

again to resume playing.

To

Turn AMS counterclockwise (or press

MD = on the remote).

Go to the preceding track

Go to the next track

Turn AMS clockwise (or press MD +

on the remote).

Press § after stopping playing.

Take out the MD

With the arrow

pointing this way

With the label side up

1

Turn on the Mini System and set the source selector to the

position for MD deck.

2

Press .

The STANDBY indicator turns off.

3

Insert an MD.

•

REC LEVEL

(ANALOG)

AMS

PUSH ENTER

0

10

p

·∏

•

REC MODE

INPUT

EDIT/NO YES

STEREO

MONO

ANALOG

REPEAT

DISPLAY/CHAR

SCROLL

PLAY MODE

TIMER

PHONES

LEVEL

REC OFF PLAY

MIN

MAX

r

)

0

§

=

+



DIGITAL

STANDBY

32 4

9

EN

Recording on MDs

Notes on Recording

If “Protected” appears in the display

The MD is record-protected. Close the slot to record on the

disc (see “To protect an MD against accidental erasure” on

page 7).

If “Din Unlock” flashes in the display

• The digital program source is not connected as you set

with INPUT in Step 4 on page 6.

To continue, connect the program source properly.

• The program source is not on.

Turn on the program source.

When the source you record from is:

• This system's CD player

– The digital signal from the CD is recorded as it is (digital

recording)*.

– Track numbers are automatically marked as on the

original CD.

• This system's tuner and tape deck

– The analog signal is converted to a digital signal and

recorded (analog recording)**.

– A track number is marked at the beginning of a recording,

but when you turn on the Level Sync function (see page

12), track numbers are automatically marked in sync with

the level of the input signal.

* For details on the limitations for digital recording, see

page 31.

** This signal is converted because these systems do not use

digital signals.

Note on MD track numbers

On an MD, the track number (track sequence), track start

and end point information, etc., are recorded in the TOC*

area independent of the sound information. You can edit

recorded tracks quickly by modifying the TOC information.

* TOC: Table Of Contents.

When “TOC” flashes in the display

The deck is currently updating the Table Of Contents (TOC).

Do not move the deck or pull out the AC power cord.

Changes to an MD made through recording are saved only

when you update the TOC by ejecting the MD or changing

the deck to standby by pressing .

The MD deck uses the SCMS (Serial Copy Management

System on page 34)

MDs recorded through digital input connector cannot be

copied onto other MDs or DAT tapes through the digital

output connector.

When recording digital signals that have been emphasized

(in the higher frequencies)

The signal is automatically de-emphasized (with attenuation

proportional to the degree of emphasis) and the level of the

de-emphasized signal is indicated on the peak level meters.

When the deck is recording or in recording pause, digital

signals input through DIGITAL IN are output to DIGITAL

OUT with the same sampling rate.

To change the digital input signal to another sampling rate

for output (without recording it to an MD), use Input

Monitor Function (see page 10).

Useful Tips for Recording

Checking the remaining recordable time on

the MD

• When you press DISPLAY/CHAR while recording,

the remaining recordable time on the MD appears.

• When you press DISPLAY/CHAR repeatedly while

the deck is stopped, the display changes as follows:

total recorded time, remaining recordable time on

the MD, disc name (see page 17).

(Continued)

•

p

·∏

•

r

)

0

§

=

+



DISPLAY/CHAR

Recording on MDs

10

EN

Monitoring the input signal (Input Monitor)

Before starting recording, you can monitor the selected

input signal through the deck’s output connectors.

1 Press § to remove the MD.

2 Set INPUT according to the input signal you want

to monitor.

When INPUT is at ANALOG

The analog signal input through LINE (ANALOG) IN is

output to DIGITAL OUT after A/D conversion, and

then to the LINE (ANALOG) OUT connectors and

PHONES jack after D/A conversion.

When INPUT is at DIGITAL

The digital signal input through DIGITAL IN is output

to DIGITAL OUT after passing through the sampling

rate converter, and then to the LINE (ANALOG) OUT

connectors and PHONES jack after D/A conversion.

Note

Even if you set REC MODE to MONO, the monitor

signal does not become monaural.

3 Press r.

If INPUT is at ANALOG, “AD-DA” appears in the

display.

If INPUT is at DIGITAL, “-DA”appears in the

display.

If “Auto Cut” appears in the display

(Auto Cut)

There has been no sound input for 30 seconds while

INPUT is set to DIGITAL and the source is connected

through DIGITAL IN. The 30 seconds of silence are

replaced by a blank of about 3 seconds and the deck

changes to recording pause.

You can turn off the Auto Cut Function

For details, see “If “Smart Space” appears in the

display”.

If “Smart Space” appears in the display

(Smart Space)

There has been an extended silence of 4 to 30 seconds

in length when INPUT is set to DIGITAL and the

source is connected through DIGITAL IN.

The silence is replaced with a blank of about 3 seconds

and the deck continues recording. Note that the tracks

before and after this three-second space may be

recorded as a single track with a single track number.

To turn off the Smart Space Function and Auto Cut

Function

1 During recording pause, press EDIT/NO repeatedly until

“S. Space ?” appears in the display.

2 Press YES.

3 Press EDIT/NO to display “S. Space OFF.”

To turn on the Smart Space Function and Auto Cut

Function again

1 During recording pause, press EDIT/NO repeatedly until

“S. Space ?” appears in the display.

2 Press YES twice to display “S. Space ON”.

Notes

• When you turn off the Smart Space Function, the Auto Cut

Function is also turned off automatically.

• The Smart Space Function and Auto Cut Function are

factory set to on.

• The Smart Space Function does not affect the order of the

track numbers being recorded, even if the blank space

occurs in the middle of a track.

• If you turn off the deck or disconnect the AC power cord,

the deck will recall the last setting (on or off) of the Smart

Space and Auto Cut Functions the next time you turn on

the deck.

Playing back tracks just recorded

Do this procedure to immediately play back tracks that

have just been recorded.

Press ﬂ (or MD ·) immediately after stopping

recording.

Playback starts from the first track of the material just

recorded.

To play from the first track of the MD after recording

1 Press p again after stopping recording.

2 Press ﬂ (or MD ·).

Playback starts from the first track of the MD.

11

EN

Recording on MDs

Recording Over Existing Tracks

Follow the procedure below to record over existing

material just as you would on an analog cassette tape.

1 Do Steps 1 to 5 in “Recording on an MD” on page

6.

2 Turn AMS (or press MD = or MD +) until

the number of the track to be recorded over

appears.

3 To record from the start of the track, continue

from Step 6 in “Recording on an MD” on page 7.

While “TRACK” flashes in the display

The deck is recording over an existing track, and stops

flashing when it reaches the end of the recorded

portion.

To record from the middle of the track

1 After Step 2 above, press ﬂ (or MD ·) to start

playback.

2 Press ﬂ (or MD P) where you want to start

recording.

3 Continue from Step 6 in “Recording on an MD” on

page 7.

Note

You cannot record from the middle of an existing track when

the “PROGRAM” or “SHUFFLE” is on.

Adjusting the Recording Level

When recording with INPUT at ANALOG and the

signal input through LINE (ANALOG) IN jacks, use

REC LEVEL to adjust the recording level before

starting recording.

You cannot adjust the recording level during digital

recording.

1 Do Steps 1 to 6 in “Recording on an MD” on

pages 6 and 7.

2 Play the portion of the program source with the

strongest signal level.

3 While monitoring the sound, turn REC LEVEL to

adjust the recording level so that the peak level

meters reach their highest point without turning

on the OVER indication. Occasional lighting of

“OVER” is acceptable.

4 Stop playing the program source.

5 To start recording, do the procedure starting from

Step 8 in “Recording on an MD” on page 7.

Without turning on the OVER indication

)0P

+

=

p

·

·ª

◊

·

)0P

+

=

p

√

MD = / MD +

= AMS +

•

p

·∏

•

r

)

0

§

=

+



•

p

·∏

•

r

)

0

§

=

+



REC LEVEL

Recording on MDs

12

EN

Marking Track Numbers while

Recording (Track Marking)

You can mark track numbers either manually or

automatically. By marking track numbers at specific

points, you can quickly locate the points later using the

AMS Function or Editing Functions.

1 Press EDIT/NO to display “LevelSync ?”during

recording or recording pause.

2 Press YES twice to display “LevelSync ON.”

“LEVEL-SYNC” appears in the display.

To cancel Automatic Track Marking

1 Press EDIT/NO during recording or recording pause.

“LevelSync ?” appears in the display.

2 Press YES.

3 Press EDIT/NO.

“LevelSyncOFF” appears in the display.

* The signal level must remain low for 2 or more seconds

before a new track number is marked.

When you want to mark track numbers after you‘ve

finished recording

Use the Divide Function (see “Dividing Recorded

Tracks” on page 25).

Note

If you turn off the deck or disconnect the AC power cord, the

deck will recall the last setting (LevelSync on or off) of the

Automatic Track Marking Function the next time you turn

on the deck.

Marking track numbers manually

(Manual Track Marking)

You can mark track numbers at any time while

recording on an MD.

Press r at the place you want to add a track mark

while recording.

Marking track numbers automatically

(Automatic Track Marking)

The deck adds track marks differently in the following

cases:

• When recording from CDs or MDs with INPUT at

DIGITAL and the source connected through

DIGITAL IN:

The deck marks track numbers automatically. When

you record from a CD or MD, the track numbers are

marked as they are found on the original.

• When recording with INPUT at ANALOG and the

source connected through LINE (ANALOG) IN, or

when recording from DAT or satellite broadcasts

with INPUT at DIGITAL and the DAT or satellite

broadcasts connected through DIGITAL IN:

The deck marks a new track number whenever the

signal level drops and rises to a certain point*

(Automatic Track Marking). If “LEVEL-SYNC” does

not light up, set the LevelSync to ON as follows:

•

p

·∏

•

r

)

0

§

=

+



YESEDIT/NO

r

13

EN

Recording on MDs

Starting Recording with

6 Seconds of Prestored Audio

Data (Time Machine Recording)

When recording from an FM or satellite broadcast, the

first few seconds of material are often lost due to the

time it takes you to ascertain the contents and press the

record button. To prevent the loss of this material, the

Time Machine Recording Function constantly stores

6 seconds of the most recent audio data in a buffer

memory so that when you begin recording the

program source, the recording actually begins with the

6 seconds of audio data stored in the buffer memory in

advance, as shown in the illustration below:

1 Do Steps 1 to 6 in “Recording on an MD” on

pages 6 and 7.

The deck changes to recording pause.

2 Start playing the program source you want to

record.

The most recent 6 seconds of audio data is stored

in the buffer memory.

Time

Recorded

portion

When you press

AMS in Step 3

Audio data in 6-second buffer memory

Beginning of the program

source to be recorded

= AMS +

•

p

·∏

•

r

)

0

§

=

+



3 Press AMS to start Time Machine Recording.

Recording of the program source starts with the

6 seconds of audio data stored in the buffer

memory.

To stop Time Machine Recording

Press p.

Note

The deck starts storing audio data when the deck is in

recording pause and you start playing the program source.

With less than 6 seconds of playing of the program source

and audio data stored in the buffer memory, Time Machine

Recording starts with less than 6 seconds of audio data.

End of the program

source to be recorded

Recording on MDs

14

EN

Synchro-Recording a CD Z

You can easily dub CDs onto MDs using the CD

synchro buttons on the remote. Track numbers are

automatically marked as appear on the original

regardless of whether “LevelSync ON” or

“LevelSyncOFF” is selected.

You may have trouble operating both units if they are

far from each other. If you do, place the Mini System

close to this deck.

1 Set the function on the Mini System to CD.

2 Do Steps 2 to 5 in “Recording on an MD” on page

6 to prepare the deck for recording.

3 Insert a CD.

4 Select the playback mode (Shuffle Play, Program

Play, etc.) on the Mini System.

5 Press CD-MD SYNC STANDBY.

The CD pauses for playing and the deck pauses

for recording.

6 Press CD-MD SYNC START.

The deck starts recording and the CD starts

playback.

The track number and elapsed recording time of

the track appear in the display.

7 Press CD-MD SYNC STOP to stop synchro-

recording.

To pause recording

Press CD-MD SYNC STANDBY.

To restart recording, press CD-MD SYNC START.

A new track number is marked each time you pause

recording.

You can use the remote of the Mini System during

synchro-recording

When you press CD p, the CD stops and the deck

pauses for recording.

When you press CD P, the CD pauses and the deck

pauses for recording.

To restart synchro-recording, press CD ·.

You can check the remaining recordable time on the

MD

Press DISPLAY (see page 17).

)0P

+

=

p

·

·ª

◊

·

)0P

+

=

p

√

CD-MD SYNC

STOP

CD P

CD-MD SYNC

START

CD-MD SYNC

STANDBY

15

EN

Recording on MDs

•

p

·∏

•

r

)

0

§

=

+



TIMER

p

Recording on an MD Using a

Timer

By connecting a timer (not supplied) to the deck, you

can start and stop recording operations at specified

times. For further information on connecting the timer

and setting the starting and ending times, refer to the

instructions that came with the timer.

1 Do Steps 1 to 7 in “Recording on an MD” on pages

6 and 7.

2 • If you want to specify the time for the start of

recording, press p.

• If you want to specify the time for the end of

recording, do Steps 8 and 9 of “Recording on an

MD” on page 7.

• If you want to specify the time for both start and

end of recording, press p.

3 Set TIMER on the deck to REC.

4 Set the timer as required.

• When you have set the time for the start of

recording, the deck turns off. When the

specified time arrives, the deck turns on and

starts recording.

• When you have set the time for the end of

recording, recording continues. When the

specified time arrives, the deck stops recording

and turns off.

• When you have set the time for both the start

and end of recording, the deck turns off. When

the starting time arrives, the deck turns on and

starts recording. When the ending time arrives,

the deck stops recording and turns off.

Synchro-Recording a Tape and

Radio Program Z

By using the MUSIC SYNC button on the remote, you

can automatically start recording in sync with the

signal input from the program source through the

LINE (ANALOG) IN jacks (Music Synchro-Recording).

The method of marking track numbers differs,

depending on the program source being recorded and

how the deck is connected to the program source. (See

“Notes on Recording” on page 9.)

1 Do Steps 1 to 5 in “Recording on an MD” on page

6.

2 Press MUSIC SYNC.

The deck changes to recording pause.

3 Start playing the program source you want to

record.

The deck starts recording automatically.

To stop Music Synchro-Recording

Press p.

Notes

• You can also use this procedure for synchro-recording

digital audio from other equipment connected to the

DIGITAL IN connector.

• When Music Synchro-Recording, the Smart Space

Function and the Auto Cut Function turn on automatically

regardless of their setting (on or off) and type of input

(digital or analog).

(Continued)

)0P

+

=

p

·

·ª

◊

·

)0P

+

=

p

√

MUSIC SYNC

Recording on MDs

16

EN

5 After you have finished using the timer, set

TIMER on the deck to OFF. Then place the deck

in standby status by plugging the AC power cord

of the deck into a wall outlet or set the timer to

continuous operation.

• If TIMER is left at REC, the deck will

automatically start recording the next time you

turn the deck on.

• If you do not change the deck to standby status

for more than a month after timer recording has

finished, the recorded contents may disappear.

Make sure to change the deck to standby status within a

month after timer recording is completed

The TOC on the MD is updated and recorded contents are

written to the MD when you turn the deck on. If the

recorded contents have disappeared, “STANDBY” flashes

when you turn the deck on.

Notes

• It may take about 30 seconds after the deck is turned on

until recording starts. When recording at a specified time

using the timer, be sure to take this time into account

when setting the recording start time.

• During timer recording, new material is recorded from the

end of the recorded portion on the MD.

• Material recorded during timer recording will be saved to

the disc the next time you turn the deck on. “TOC” will

flash in the display at that time. Do not move the deck or

pull out the AC power cord while “TOC” is flashing.

• Timer recording will stop if the disc becomes full.

17

EN

Playing MDs

Using the Display

You can use the display to check disc and track

information such as the total track number, total

playing time of the tracks, remaining recordable time

of the disc and disc name.

When you insert an MD, the disc name, total number

of tracks, and total disc playing time appear in the

display as follows:

Playing MDs

Total number of tracks Total disc playing time

The disc name appears, followed by the total number

of tracks (Tr) and total disc playing time.

A music calendar showing all the track numbers

appears within a grid if the MD is a premastered disc,

or without a grid if the MD is a recordable disc.

If the total track number exceeds 25, z appears to the

right of number 25 in the music calendar.

To label a recordable disc and its tracks, see “Labeling

Recordings” on page 28.

Note

When you insert a new MD or turn off the deck and turn it

on again, the last item displayed will reappear.

If, however, you disconnect the AC power cord, the display

will show the total track number and total playing time of all

recorded tracks the next time you turn on the deck, no

matter what the last display was.

Disc name Music calendar

Checking the total track number, total disc

playing time, remaining recordable time of

the disc and the title of the disc

Each time you press DISPLAY/CHAR (or DISPLAY)

while the deck is stopped, you can change the display

as follows:

Remaining recordable time of the disc

(Recorded MDs only)

Disc name

Press

The remaining recordable time of the disc

is not shown for premastered MDs.

Press

Total track number and total playing

time of all recorded tracks

)0P

+

=

p

·

·ª

◊

·

)0P

+

=

p

√

SCROLL

DISPLAY

√

•

SCROLL

DISPLAY/CHAR

18

EN

Playing MDs

Locating a Specific Track

You can quickly locate any track while playing a disc

by using AMS (Automatic Music Sensor), MD = and

MD +.

You can check the track name at any time while

playing an MD

Press SCROLL.

Since the display shows up to 12 characters at a time,

press SCROLL again to see the rest of the track title if

the title has 13 characters or more.

Press SCROLL again to pause scrolling, and again to

continue scrolling.

Do the following:

The next or

succeeding tracks

During playback, turn AMS clockwise

(or press MD + repeatedly) until

you find the track.

The current or

preceding tracks

During playback, turn AMS

counterclockwise (or press MD =

repeatedly) until you find the track.

A specific track by

using AMS

1 Turn AMS until the track number

you want to locate appears while

the deck is stopped. (The track

number is flashing.)

2 Press AMS or ﬂ.

To locate

Checking remaining time and the title of a

track

Each time you press DISPLAY/CHAR (or DISPLAY)

while playing an MD, you can change the display as

shown below. The track numbers in the music

calendar disappear after they are played.

Track number and playing time of the

current track

Track number and remaining time of

the current track

Press

Track name

Press

If no title is recorded, “No Name” appears,

followed by the elapsed playing time.

)0P

+

=

p

·

·ª

◊

·

)0P

+

=

p

√

MD = / MD +

•

p

·∏

•

r

)

0

§

=

+



= AMS +

√

19

EN

Playing MDs

Locating a Particular Point in a

Track

You can also use 0 and ) to locate a particular

point in a track during playback or playback pause.

To locate a point Press

While monitoring the

sound

) (forward) or 0 (backward)

and keep pressing until you find

the point.

Quickly by observing

the display during

playback pause

) or 0 and keep pressing

until you find the point. There is

no sound output during this

operation.

Notes

• If the disc reaches the end while you are pressing )

during playback pause, “OVER” appears in the display.

Press 0 (or MD =) or turn AMS counterclockwise to

go back.

• If the disc reaches the end while you are pressing )

during sound monitoring, the deck stops.

• Tracks that are only a few seconds long may be too short

to scan using the search function. For such tracks, it is

better to play the MD at normal speed.

•

p

·∏

•

r

)

0

§

=

+



0/)

To pause playing at the beginning of a track

Turn AMS (or press MD = or MD +) after pausing

playback.

To go quickly to the beginning of the last track

Turn AMS counterclockwise (or press MD =) while

the display shows the total track number and total disc

playing time, remaining recordable time of the disc, or

disc name (see page 17).

20

EN

Playing MDs

Playing Tracks Repeatedly

You can play tracks repeatedly in any play mode.

Press REPEAT.

“REPEAT” appears in the display.

The deck repeats the tracks as follows:

When the MD is

played in

Normal play (page 8)

Shuffle Play (page 20)

Program Play (page 21)

The deck repeats

All the tracks

To cancel repeat play

Press REPEAT several times until “REPEAT” disappears.

The deck returns to the original playing mode.

Repeating the current track

While the track you want to repeat is playing in

normal play, press REPEAT several times until

“REPEAT 1” appears in the display.

All the tracks in random order

The same program

)0P

+

=

p

·

·ª

◊

·

)0P

+

=

p

√

REPEAT

•

REPEAT

Playing in Random Order

(Shuffle Play)

You can have the deck “shuffle” tracks and play them

in random order.

1 Press PLAY MODE repeatedly until “SHUFFLE”

appears in the display when the deck is stopped.

2 Press ﬂ (or MD ·) to start Shuffle Play.

“J” appears in the display while the deck is

“shuffling” the tracks.

To cancel Shuffle Play

Press PLAY MODE repeatedly until “SHUFFLE” disappears

when the deck is stopped.

You can specify tracks during Shuffle Play

• To play the next track, turn AMS clockwise (or press

MD +).

• To play from the beginning of the current track again,

turn AMS counterclockwise (or press MD =). You

cannot use AMS (or MD =) to go to tracks that

have already been played.

)0P

+

=

p

·

·ª

◊

·

)0P

+

=

p

√

MD ·

•

p

·∏

•

r

)

0

§

=

+



PLAY MODE ·∏

La page charge ...

Sony MDS-S707 Mode d'emploi

Sony MDS-S707 Mode d'emploi

dans d''autres langues

Documents connexes