Midmark M9/M11 Self -Contained Steam Sterilizer (-033 thru -034) Mode d'emploi

English

Français

For Models:

xxxx (-001)

xxxx (-002)

User Guide

Data Logger (9A682001)

User Guide

003-10279-99 Rev. AA5 (10/21/20)

Style P

Applies to Models:

M9 (-020 /-021 /-022)

(-033 /-034)

(-040 /-041 /-042 /-043)

M9-D (-020 /-022 /-042

M11 (-020 /-021 /-022)

(-033 /-034)

(-040 /-041 /-042 /-043)

M11-D (-020 /-022)

English - 2

003-10279-99 © Midmark Corporation 2020

Table of Contents

Important Information

Safety Instructions ...................................3

Electromagnetic Interference .................3

Safety Symbols ........................................4

Symbol Glossary .....................................4

Transportation / Storage Conditions .....4

Intended Use ...........................................5

Capabilities ...............................................5

Identify Compatible Sterilizer Models. .. 5

Controls & Indicators ...............................6

USB Drive ................................................7

Operation

Home Screen. ......................................... 8

During the Cycle. ....................................8

Cycle Complete. .....................................9

Cycle Accepted by Operator. .................9

Cycle Rejected by Operator. ................10

Additional Menus

Menu Navigation. .................................. 11

Product Info Menus. .............................. 11

View Data Logger Serial Number .... 11

View Sterilizer Serial Number ........... 11

View Data Logger Firmware Version 11

Set Date / Time. .....................................12

Set User Setup. .....................................13

Set Sterilizer Name. ..............................14

Set Sterilizer Serial Number. ...............15

Sample Sterilization Cycle Log (PDF). 16

Specications

Operating Environment .........................18

Maintenance / Troubleshooting

Maintaining Your Data Logger .............18

Calling for Service .................................18

Troubleshooting / Error Codes ...........19

Warranty

Scope of Warranty .................................20

English - 3

003-10279-99 © Midmark Corporation 2020

Important Information

Safety Instructions

The primary concern of Midmark is that this equipment is operated and maintained with the safety of the

patient and sta in mind. To assure safe and reliable operation:

•Read and understand this manual before attempting to setup or operate the Data Logger.

•Assure that the appropriate personnel are informed on the contents of this manual.

Electromagnetic Interference

The Midmark Data Logger is intended for use in the electromagnetic environment as specified in the

Midmark Sterilizer User Guide. The customer or the user of the Midmark Data Logger should assure that

it is used in such an environment.

This product is designed and built to minimize electromagnetic interference with other devices. However,

if interference is noticed between another device and this product:

• Remove interfering device from room.

• Plug device into isolated circuit.

• Increase separation between Data Logger and interfering device.

• Contact Midmark Corporation if interference persists.

WARNING

Use of accessories, transducers and cables other than those specified or provided by the

manufacturer of this equipment could result in increased electromagnetic emissions or

decreased electromagnetic immunity of this equipment and result in improper operation.

WARNING

Use of this equipment adjacent to or stacked with other equipment should be avoided because

it could result in improper operation. If such use is necessary, this equipment and the other

equipment should be observed to verify that they are operating normally.

Equipment Alert

Portable RF communications equipment (including peripherals such as antenna cables and

external antennas) should be used no closer than 30 cm (12 inches) to any part of the device,

including cables specified by the manufacturer. Otherwise, degradation of the performance of

this equipment could result.

English - 4

003-10279-99 © Midmark Corporation 2020

Safety Symbols

WARNING

Indicates a potentially hazardous situation which could result in serious injury.

Equipment Alert

Indicates a potentially hazardous situation which could result in equipment damage.

Caution

Indicates a potentially hazardous situation which may result in minor or moderate injury.

It may also be used to alert against unsafe practices

Proper shipping orientation

Fragile

Keep dry

Symbol Glossary

Date of Manufacture

Manufacture

Catalogue Number

Serial Number

Transportation / Storage Conditions

Ambient Temperature Range: -22°F to 140°F (-30°C to +60°C)

Relative Humidity: 10% to 90% (non-condensing)

Atmospheric Pressure: 7.2 psia to 15.4 psia (49.6 kPa to 106.4 kPa)

English - 5

003-10279-99 © Midmark Corporation 2020

Identify Compatible Sterilizer Models.

The Data Logger is compatible with the

-02X, -03X, & -04X model sterilizers. Use

the images to identify sterilizer models

when needed.

Intended Use

The Midmark Data Logger is designed to connect with a Midmark sterilizer and electronically

store sterilizer cycle data such as: sterilizer serial number, date and time the cycle was run,

sterilization cycle parameters, errors and the cycle approving authority.

Capabilities

The Data Logger accessory is compatible with Midmark/Ritter M9/M9D-02X/-03X/-04X and

M11/M11D-02X/-03X/-04X sterilizers and is used to create an electronic record of the

sterilization cycle. The Data Logger stores an electronic record of the sterilization cycle data

with date and time, sterilizer identification (8 character maximum) and the approving operator

(3 character maximum). The Data Logger stores the data and automatically downloads a pdf

file to the included USB for easy transfer to a PC for access and backup. Additionally, the Data

Logger stores up to 12 operator IDs for easy access by multiple operators.

NOTE: The Data Logger cannot be used in conjunction with printers 9A259001 or 9A599001.

-02X & -03X Model Sterilizer

-04X Model Sterilizer

English - 6

003-10279-99 © Midmark Corporation 2020

Button 1 thru 4

Button 6

Controls & Indicators

Button 5

The different keys perform the following functions:

Button 1 thru 4: Selects the function directly above it on the display when available.

Button 5: (Minus) – Scrolls down through the menus or values.

Button 6: (Plus) – Scrolls up through the menus or values.

Button 7: (Enter) – Selects value or advances menu.

Button 7

English - 7

003-10279-99 © Midmark Corporation 2020

USB Drive.

• To ensure compatibility only use USB drives provided by Midmark for the Data Logger.

• Midmark recommends backing up contents of the Data Logger to a PC daily, or at least weekly

at a minimum.

• The USB drive is used to transfer data from Data Logger to PC for backup.

• Ensure USB Cover is closed while Sterilizer and Data Logger are in use.

• If utilizing a brand new USB Drive it may take more time to transfer all the files (depending on

number of cycles ran). This is a one time event for each new USB drive.

USB Drive

Part # 002-10502-00

USB Cover

Equipment Alert

After reinstallingUSBintoDataLoggerallowallles

to copy prior to using sterilizer.

Equipment Alert

USB should not be removed

from the Data Logger while a

sterilization cycle is in progress.

Transferring data from Data Logger to PC for backup.

• Remove USB from the Data Logger.

• Plug USB into a PC.

• Navigate to the File Explorer on the PC.

• Open up the USB Drive Folder on the PC.

• Navigate to the correct folder labeled as the sterilizer serial number.

• Transfer data to the PC.

• Consult with an appropriate IT professional for support with file transfer if

required.

English - 8

003-10279-99 © Midmark Corporation 2020

Operation

Home Screen.

• One of these main menus will appear on the Data Logger when it is ready for a cycle to be

run. The default screen will show MIDMARK unless the sterilizer name was setup.

• -04X models do not show the date and time on the Data Logger display.

During the Cycle.

• Data Logger indicates sterilization cycle progress by flashing the bar under the active cycle

phase.

-02X & -03X Models

-04X Models

Caution

If user stops a cycle during the dry cycle phase, the instruments will

need to be inspected to ensure they are dry prior to accepting load.

English - 9

003-10279-99 © Midmark Corporation 2020

Cycle Complete.

• When sterilization cycle is complete press ENTER ( ) then select your operator sign off button.

Cycle Accepted by Operator.

• To accept cycle press ACCEPT button then press DONE button. Cycle information will be

recorded by Data Logger, Sterilizer is ready to run the next cycle.

Note

After cycle completes, open the door and examine the condition of the instruments.

AcceptorRejectthesterilizationloadbasedonyoursterilizationprotocols.Qualied

personnel responsible for infection control should prepare a protocol for handling

sterilized items. This protocol should be followed by all personnel responsible for

handling sterilized items.

English - 10

003-10279-99 © Midmark Corporation 2020

Cycle Rejected by Operator.

• To reject cycle press REJECT button then press PLUS or MINUS button to navigate to

the failure reason and ENTER ( ). Cycle information will be recorded by Data Logger,

Sterilizer is ready to run the next cycle.

English - 11

003-10279-99 © Midmark Corporation 2020

Menu Navigation.

• PLUS, MINUS changes characters.

- Press and hold to scroll through available characters when entering data.

• NEXT advances to next field.

• DONE advances to next menu when entering data is complete.

• BACK deletes the previous character/returns to the previous menu.

Blank Spaces

To enter a blank space in a character string on Data Logger, navigate to blank character located

between letter A and number 9 then press NEXT/DONE.

Pressing ENTER ( )

Pressing ENTER ( ) at any point accepts all characters left of flashing cursor completing that

step. This could result in unwanted blank fields.

Product Info Menus.

• Navigate to the Product Info menu using the MINUS button then press ENTER ( ).

• Use PLUS, MINUS buttons to view Data Logger Serial Number, Sterilizer Serial Number,

and current Firmware Version.

• Press BACK button once to return to the previous menu or twice to return to the main menu.

Additional Menus

English - 12

003-10279-99 © Midmark Corporation 2020

Set Date / Time.

• Navigate to the Set Date / Time menu using the MINUS button then press ENTER ( ).

• Use PLUS, MINUS buttons to adjust the values for each menu then press NEXT.

• When finished setting AM / PM press the DONE button to complete the Date and Time setup.

Note

Setting Date/Time is not required for any -04X model sterilizers. These models use Date/

Time from sterilizer not the Data Logger for sterilization records.

English - 13

003-10279-99 © Midmark Corporation 2020

User Setup.

• Navigate to the User Setup menu using MINUS button then press ENTER ( ).

• From 1 to 12 users (originally designated U01-U12) can be set up in the Data Logger. Use PLUS,

MINUS to scroll through the user identifiers to select one for setup.

• Enter a unique 1 to 3 character identifier for each user of the sterilizer using PLUS, MINUS,

NEXT, DONE. When all users have been entered and identified, select “No” when prompted to

set up another user.

Note

User Name will be part of electronic record on

receipt. Setting up user names is optional.

English - 14

003-10279-99 © Midmark Corporation 2020

Set Sterilizer Name.

• Navigate to the Set Sterilizer Name menu using MINUS button then press ENTER ( ).

• Enter sterilizer name by using PLUS, MINUS, NEXT/DONE and BACK buttons.

• Sterilizer name can be from 1 to 8 characters.

Note

Sterilizer Name will be part of electronic record

on receipt. Setting up sterilizer name is optional.

English - 15

003-10279-99 © Midmark Corporation 2020

Set Sterilizer Serial Number.

• Navigate to the Set Sterilizer Serial Number menu using MINUS button then press ENTER ( ).

• Enter sterilizer serial number by using PLUS, MINUS, NEXT/DONE and BACK buttons.

• Serial Number can be up to 9 characters. If Serial Number is shorter than 9 characters navigate

to the blank space (between A and 9) and press NEXT/DONE, or press ENTER ( ) after the

last character is entered.

Serial Number

Note

Ensure sterilizer serial number being assigned

to Data Logger is correct so sterilization data

records will be maintained accurately.

English - 16

003-10279-99 © Midmark Corporation 2020

Sterilizer Name

Sterilizer ID

(Serial Number)

Sterilization Cycle Log (PDF)

Midmark M11 - v1.0.4

Total Cycles: 41

Name: MIDMARK

Sterilizer ID: V2072130

01/16/202X 08:54 AM

BEGIN UNWRAPPED CYCLE

Temp: 270 Degrees F

Time: 3 Minutes

Dry: 1 Minutes

FILLING CHAMBER

HEATING

mm:ss

0:00

0:30

1:00

1:30

2:00

2:30

3:00

3:30

4:00

4:30

5:00

5:30

6:00

6:30

7:00

7:30

8:00

8:30

9:00

9:30

10:00

10:30

11:00

11:30

12:00

12:30

13:00

13:30

14:00

14:30

15:00

15:30

16:00

16:30

17:00

17:30

18:00

18:30

19:00

19:30

20:00

20:30

21:00

21:30

22:00

22:30

23:00

Degrees

66.2 F

66.3 F

66.6 F

68.1 F

71.4 F

77.2 F

87.8 F

89.4 F

90.7 F

92.6 F

93.3 F

100.7 F

110.1 F

120.4 F

132.5 F

145.9 F

155.3 F

161.7 F

167.9 F

173.8 F

178.9 F

182.5 F

187.1 F

191.7 F

195.9 F

199.7 F

203.4 F

207.4 F

210.4 F

213.1 F

213.3 F

216.5 F

219.6 F

222.9 F

225.9 F

228.6 F

231.4 F

233.9 F

236.7 F

239.3 F

236.6 F

233.4 F

235.9 F

239.2 F

242.3 F

244.0 F

239.2 F

PSI

0.0

0.4

1.2

2.0

3.0

4.0

4.9

5.9

6.9

7.9

8.9

9.8

10.9

11.9

12.9

9.8

6.0

5.8

6.8

7.8

8.8

9.8

10.9

12.0

13.2

10.3

8.1

9.5

11.0

12.4

12.5

10.0

Total # of cycles

run on unit

Date and Time

of cycle start

Selected Cycle

Indicates Filling

phase initiated

During Heating phase,

the Data Logger records

chamber temperature

and pressure in 30

second increments

Model # and

Software Version

Sterilization temperature,

time, and dry time settings

Continued:

Note

The Data Logger stores

detailed descriptions of

each sterilization cycle

as printable PDF’s. The

Data Logger stores these

lesinautomatically

created folders by date.

23:30

24:00

24:30

25:00

25:30

26:00

26:30

27:00

27:30

28:00

28:30

29:00

29:30

237.9 F

241.5 F

245.1 F

248.4 F

251.5 F

254.6 F

257.4 F

260.3 F

263.1 F

265.7 F

268.5 F

271.0 F

272.6 F

9.6

11.4

13.1

14.7

16.4

18.0

19.6

21.3

23.0

24.7

26.4

28.2

28.9

STERILIZING

mm:ss

0:00

0:30

1:00

1:30

2:00

2:30

3:00

Degrees

271.6 F

271.9 F

272.3 F

272.6 F

272.9 F

272.7 F

272.2 F

PSI

28.6

28.5

28.8

29.1

29.3

29.4

29.0

Min

Max

271.6 F

272.9 F

28.4

29.4

VENTING CHAMBER

DRYING

mm:ss

0:00

1:00

Drying Start

Drying Complete

FILLING: 0:40

HEATING: 29:44

STERILIZING: 3:00

VENTING: 2:56

DRYING: 1:00

TOTAL CYCLE: 00:37:19

CYCLE COMPLETE

01/16/202X 09:32 AM

ACCEPTED: X

REJECTED:

Operator: A02

During Sterilization

phase, the Data Logger

records chamber

temperature and

pressure in 30 second

increments

Indicates Venting

phase initiated

Cycle summary

Operator summary

load accepted

Indicates Drying

phase initiated

Indicates Sterilizing

phase initiated

Normal Cycle Log.

• This is an example of a

completed and approved

sterilization cycle.

English - 17

003-10279-99 © Midmark Corporation 2020

Continued:

STERILIZING

mm:ss

0:00

0:30

1:00

1:30

2:00

2:30

Degrees

271.6 F

271.9 F

272.3 F

272.6 F

272.9 F

272.7 F

PSI

28.6

28.5

28.8

29.1

29.3

29.4

C104: STERILIZE MODE

STOP PRESSED

CHAMBER TEMP 273F

CHAMBER PRESS 29.0PSI

ELAPSED TIME 02:38

* * ITEMS NOT STERILE * *

10/20/202X 03:52 PM

During Sterilization phase,

the printer records chamber

temperature and pressure in

30 second increments

Items Not Sterile

Cycle parameters at

time of error

Date and

time of error

Error code and

description

Sterilizer Cycle Log With Error Code (example).

• ITEMS NOT STERILE When an error code occurs during a cycle the load being sterilized is not

sterile.

• Example below shows the stop button was pressed during the sterilization cycle causing an error

code C104 and interrupting the cycle.

• Parameters at the time of the error are shown which could potentially help with troubleshooting

processes. Date and time error occurred is also shown.

Sterilizer Cycle Log Rejected By Operator.

• Example below shows the sterilization cycle was rejected by the operator due to a failed

indicator.

• The parameters at the time of the error are shown which could potentially help with

troubleshooting processes. The date and time the error occurred is also shown.

Continued:

FILLING: 0:40

HEATING: 29:44

STERILIZING: 3:00

VENTING: 2:56

DRYING: 1:00

TOTAL CYCLE: 00:37:19

CYCLE COMPLETE

01/16/202X 09:32 AM

ACCEPTED:

REJECTED: X

Reason: Fail Indicator

Operator: A02

Cycle summary

Operator summary

load rejected due to

failed indicator.

English - 18

Operating Environment

Ambient Temperature 68°F to 104°F (+20°C to +40°C)

Relative Humidity < 80% (non-condensing)

Normal Operating Altitude: < 9842 ft. (3000 m) above sea level

Operating Environment Indoor use only

Specications

Maintaining Your Data Logger

Maintenance / Troubleshooting

Clean External Surfaces

A) Clean the exterior of the Data Logger each day according to your facility’s procedure for clinical

contact surfaces, noting the following: (Use only quaternary disinfectants to disinfect unit. Staining,

pitting, discoloration, or softening could occur if phenolic, iodophor, or glutaraldehyde-based

disinfectant is used on plastic surfaces of the unit. Also, use of alcohol or aerosol spray cleaner /

disinfectant containing substantial amounts of alcohol in the formula can damage the faceplate).

B) Wring excess solution from the cloth.

C) Using soft cloth, wipe all external surfaces.

D) Follow the instructions provided with the cleaner / disinfectant used regarding rinsing and drying

of the external surfaces.

Calling for Service

Contact your Midmark Authorized Dealer, or log on to www.midmark.com. Model and serial number

information will be required when calling for service and can be found on the back of the unit.

To contact Midmark directly:

1-800-Midmark (1-800-643-6275) or 937-526-3662

8:00 am to 5:00 pm EST (Monday thru Friday)

(Excluding standard U.S. holidays)

Equipment Alert

Make sure the USB cover is closed when cleaning to prevent

entry of cleaners/moisture into the USB cavity.

English - 19

Troubleshooting / Error Codes

Display / Symptom Cause Check/ Action

Memory Error

Error trying to read or write configuration

data internal to Data Logger.

Cycle power to Data Logger.

If error persists, replace Data Logger.

SD Card Error

Failure to read or write to SD card or SD

card has become disconnected.

Cycle power to Data Logger.

If error persists, replace Data Logger.

USB Drive Error

Failure to read or write to USB drive. Make sure USB drive is securely inserted.

Cycle power to Data Logger.

Replace USB Drive

If error persists, replace Data Logger.

File Transfer Error

Failure to copy one or more files from SD

card to USB drive.

Remove USB drive from Data Logger and

re-insert. This will initiate the file transfer from

SD card to USB drive.

If error persists, replace USB drive.

If error persists, replace Data Logger.

USB drive is disconnected during file

transfer process.

Remove USB drive from Data Logger and

re-insert. This will initiate the file transfer from

SD card to USB drive.

If error persists, replace USB drive.

If error persists, replace Data Logger.

Clock Battery Error

Internal clock battery is either low on power

or dead.

Replace Data Logger.

PDF Creation Error

Error creating pdf of sterilization cycle or

saving file to SD card.

Run another sterilization cycle, if error

persists, replace Data Logger.

Config File Copy Error

Data Logger is unable to read configuration

parameters from config file on SD card.

Remove USB drive from Data Logger. Delete

config file from USB drive and download

a new config file onto the USB drive using

online registration process. Insert USB drive

into Data Logger and update config file.

If error persists, replace USB drive with

new Config file downloaded using online

registration process.

If error persists, replace Data Logger.

Firmware Update Error

Data Logger encountered an error while

updating firmware.

Restart Data Logger with a USB drive that

contains firmware update file to re-initiate

firmware update.

If error persists, get a new USB drive with a

new firmware update file and retry.

If error persists, replace Data Logger.

Button Stuck Error

Data Logger detects a button on membrane

is stuck.

Try to manually unstick button and restart

Data Logger.

If the error persists, replace Data Logger.

English - 20

SCOPE OF WARRANTY Midmark Corporation (“Midmark”) warrants to the original retail purchaser that it will, at Midmark’s option, repair or

replace components of the domestic and international medical products manufactured by Midmark (except for components not warranted

under “Exclusions”) that are defective in material or workmanship under normal use and service. The sole remedy under this limited warran-

ty is the repair or replacement, at Midmark’s option, of the applicable components. This limited warranty shall only apply to defects that are

reported to Midmark within the applicable warranty period and which are determined to exist upon examination by Midmark,. This warranty

extends only to the original retail purchaser of a product and is not transferable or assignable. Replacement components or products may

be used and/or refurbished components or products, provided they are of like quality and speci cations as new components or products.

Midmark warrants to the original retail purchaser that during the applicable warranty period it will repair or replace software contained

within the products manufactured by Midmark (except for those not warranted under “Exclusions”) if: (1) the media on which the software is

furnished exhibits defects in material or workmanship under normal use; or (2) the software does not substantially conform to its published

speci cations.

APPLICABLE WARRANTY PERIOD The applicable warranty period, measured from the date of invoice to the original retail purchaser of

the product and shall be one (1) year for all warranted products and components.

OBTAINING WARRANTY SERVICE Warranty service must be obtained through either Midmark or an authorized dealer in the Midmark

product line for which warranty service is requested. Midmark may be contacted for warranty service inquiries or issues via email at www.

midmark.com; by phone at 1-800-MIDMARK or by mail to Midmark Corporation, 60 Vista Drive, Versailles, Ohio 45380. It is the retail pur-

chaser’s obligation to arrange for delivery of a product to Midmark or one of its authorized dealers for warranty service, which delivery shall

be at retail purchaser’s expense. It is also the retail purchaser’s obligation to comply with the warranty service instructions provided either

by Midmark or its authorized dealer. The retail purchaser must provide Midmark with completed warranty registration information within

thirty (30) days after purchase in order to obtain the bene ts of this limited warranty.

EXCLUSIONS: This limited warranty does not cover and Midmark shall not be liable for the following:

(1) Defects, damage or other conditions caused, in whole or in part, by misuse, abuse, negligence, alteration, accident, freight damage,

negligent storage, tampering or failure to seek and obtain repair or replacement in a timely manner;

(2) Products which are not installed, used, and properly cleaned and maintained as required or recommended in the Midmark “Installation”

and/or “Installation/Operation Manual” for the applicable product, including the speci ed structural and operational environmental conditions

and electrical requirements;

(3) Products considered to be of a consumable or sterile nature;

(4) Accessories or parts not manufactured by Midmark;

(5) Charges by anyone for adjustments, repairs, replacement parts, installation or other work performed upon or in connection with such

products which are not expressly authorized in writing in advance by Midmark;

(6) Costs and expenses of routine maintenance and cleaning; and

(7) Representations and warranties made by any person or entity other than Midmark.

(8) Matching of color, grain or texture except to commercially acceptable standards;

(9) Changes in color caused by natural or arti cial light;

(10) Custom manufactured products;

(11) Alterations or modi cations to the product by any person or entity other than Midmark; and

(12) Products that would otherwise by covered under this limited warranty, but are acquired: (i) from a person or entity that is not Midmark

or one of its authorized dealers; or (ii) from a Midmark dealer that is not authorized to sell the product at issue in the geographic territory

where the purchaser is located, or is not authorized to sell the product at issue within the medical market.

SOFTWARE; WITH RESPECT TO SOFTWARE THAT IS A PRODUCT OR COMPONENT THEREOF, MIDMARK DOES NOT WARRANT

THAT THE SOFTWARE: (1) IS ERROR FREE; (2) CAN BE USED WITHOUT PROBLEMS OR INTERRUPTIONS; OR (3) IS FREE FROM

VULNERABILITY TO INTRUSION OR ATTACK BY VIRUSES OR OTHER METHODS.

EXCLUSIVE REMEDY; CONSEQUENTIAL DAMAGES DISCLAIMER MIDMARK’S ONLY OBLIGATION UNDER THIS LIMITED WARRAN-

TY IS THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS. MIDMARK SHALL NOT BE LIABLE FOR AND HEREBY DISCLAIMS

ANY DIRECT, SPECIAL, INDIRECT, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES OR DELAYS, INCLUDING, BUT

NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS OR INCOME, LOSS OF USE, LOSS OF DATA, DOWNTIME, COVER AND

EMPLOYEE OR INDEPENDENT CONTRACTOR WAGES, PAYMENTS AND BENEFITS. THIS DISCLAIMER SHALL SURVIVE ANY

FAILURE OR ASSERTED FAILURE OF THE ESSENTIAL PURPOSE OF THIS LIMITED WARRANTY OR ITS REMEDIES SPECIFIED

HEREIN. WARRANTY DISCLAIMER THIS WARRANTY IS MIDMARK’S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRAN-

TIES, EXPRESS OR IMPLIED. MIDMARK MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY IMPLIED WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACE-

MENT OF DEFECTIVE PARTS.

STATUTE OF LIMITATIONS No action may be brought against Midmark for breach of this limited warranty, an implied warranty, if any, or for

any other claim arising out of or relating to the products, more than ninety (90) days following expiration of the limited warranty period.

NO AUTHORIZATION No person or  rm is authorized to create or approve for Midmark any other obligation or liability in connection with

the products.

Warranty Information

La page charge ...

Midmark M9/M11 Self -Contained Steam Sterilizer (-033 thru -034) Mode d'emploi

Ce manuel convient également à

Midmark M9/M11 Self -Contained Steam Sterilizer (-033 thru -034) Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents