Haier ESL-T21 Manuel utilisateur

Top Load

Clothes Washer

User Manual-

Guide de l’Utilisateur-

Manual del Usuario-

Model #

Modèle

Para Modelo de

ESL-T21

Chargement

superieure Lave-linge

Lavarropas

Máxima Carga

IMPORTANT SAFETY INSTRUCTIONS

Warning – To reduce the risk of fire, electric shock, or injury

to persons when using your appliance, follow basic

precautions, including the following:

1. Read all instructions before using the appliance.

2. Use this appliance only for its intended purpose as described

in this use and care guide.

3. Use only detergents or softeners recommended for use in a clothes

washer and keep them out of the reach of children.

4. This washer must be properly installed in accordance with the

installation instructions before it is used.

5. Never unplug your washer by pulling on the power cord. Always

grasp the plug firmly and pull straight out from the outlet.

6. Replace immediately worn power cords, loose plugs/power outlets.

7. Unplug your washer before cleaning or before making any repairs.

8. If your old washer is not being used, we recommend that you

remove the door. This will reduce the possibility of danger to children.

9. Do not operate your washer in the presence of explosive fumes.

10. Do not use washer to wash clothes soaked, spotted or washed in

gasoline, dry cleaning solvents or any other explosive or flammable

substances that could ignite and explode.

11. Clothes or rags used to clean flammable or explosive materials should

not be washed in the washer till all traces of this material has been

removed, to avoid an accident.

12. Do not add or mix any flammable or explosive substances to the wash.

13. Do not try to remove clothes while the tub or the agitator is moving. Let it

come to a complete stop before use.

14. Washer loading door must be closed when agitator and tub is spinning.

15. Do not operate your washer when parts are missing or parts are broken.

16. Do not use the washer for commercial clothes washing.

17. Do not operate washer unless all enclosure panels are properly in place.

18. Do not tamper with controls.

19. To reduce risk of injury do not allow children to play in or on the washer.

20. Washer must be connected to proper electrical outlet with the correct

electrical supply.

1

English

2

21. Proper grounding must be ensured to reduce the risk of shock and fire.

DO NOT CUT OR REMOVE THE GROUNDING PLUG. If you do not

have a three-prong electric receptacle outlet in the wall, have a certified

electrician install the proper receptacle. The wall receptacle MUST be

properly grounded.

22. Hydrogen gas may be produced if the water heater has not been used in

more then 2 weeks. This could be explosive and can explode under

certain circumstances. If this is the case, before using the washer turn on

all the hot faucet's and let the hot water run for a few minutes. This will

let the trapped hydrogen escape. During this process do not turn on an

electric appliance, smoke, light a match/lighter or use a flame to avoid

an accident, as hydrogen gas is flammable and can explode.

SAVE THESE INSTRUCTIONS

For Future Use

English

Thank you for using our Haier

product. This easy-to-use manual will

guide you in getting the best use of

your washer.

Remember to record the model and

serial number. They are on a label in

back of the washer.

Model number

Serial number

Date of purchase

Staple your receipt to your manual. You will need it to obtain

warranty service.

DANGER

Risk of child entrapment. Before you throw away your old

washer, take off the door so that children may

not easily get trapped inside.

Table Of Contents

PAGE

SAFETY INSTRUCTIONS ....................................................................1

OPERATING INSTRUCTIONS ............................................................4

Parts and Features ..................................................................................4

Operations ........................................................................................5-6

Normal Operating Sounds....................................................................12

Lint Filter..............................................................................................13

Safety Lid Switch ..................................................................................13

Care and Cleaning Guide ............................................................14

Cleaning and Maintenance ..................................................................14

Moving and Vacationing ......................................................................15

Storage of Your Washer ......................................................................15

Troubleshooting..............................................................................16

INSTALLATION INSTRUCTIONS ....................................................18

Tools and Materials Required ................................................................18

Unpacking Your Washer ......................................................................19

Leveling Your Washer ..........................................................................19

Steps for Installation ............................................................................20

Electrical Connections ....................................................................22

Grounding Instructions..........................................................................22

Power Interruptions ..............................................................................22

Warranty ........................................................................................23

3

English

4

English

Control Panel

1. Liquid Fabric Softener Dispenser

2. Inner Wash Tub

3. Liquid Bleach Dispenser

4. Agitator

5. Control Panel

5

1

2

3

4

OPERATING INSTRUCTIONS

Parts and Features

5

English

Operations

Delay Start

• When not activated the display shows cycle remaining time through the wash

process.

• When Delay Start is selected the indicator light will display a minimum delay of 2

hours. Push button once for every additional 1 hour delay for up to 24 hours.

Cycles

• Normal - For regular washing.

• Heavy – For washing bigger, thicker and heavier dirty laundries.

• Cotton – For washing cotton fabrics.

• Quick – For quick washing of light dirty laundries.

• Delicate – For washing of delicate fabrics.

• Hand Wash – To have hand wash effect on clothes.

Soil Level

• Select clothes soil level.

• Wash cycle increases 2 minutes for every soil level increased.

Load Size

• Water levels may be set at the beginning of the wash or at pause.

• During Soak, Wash or Rinse press this button to manually replenish water. Release

to stop. Function automatically is inactive when water reaches the overflow protec-

tion level.

Speed Wash/Spin

• Select spin speed when program is in normal or delicate cycle.

Note: • Flashing light indicates the program is running.

• Steady light indicates the program is the selected mode or is

about to operate.

6

English

Power On/Off

• Push button once to power on the washer.

• If washer is On push button once to shut off the power.

Start/Pause

• Once washer is powered and selections are chosen push this button once to Start

the wash.

• While unit is working push this button once to pause it.

• If unit is in Pause mode, push this button once to resume operation.

Cycle Signal

• Signal volume can be adjusted soft – loud or off.

Temperature Wash/Rinse

• To select inlet water temperature for wash and rinse.

Process Select

This is to select washing process.

• Soak will not work in the Hand Wash, Delicates and Quick cycles.

• Water level indicator will shut off if only Spin is selected.

• Once a program is selected press the Process Select button to have 2nd Rinse. The

washer will add a 2nd rinse.

Delay Start Indicator

• Indicates remaining minutes when cycle is in progress.

• Indicates remaining hours during delay process.

• Indicates faults codes or conditions that are not normal.

7

English

Operating Procedure

1. Press power on button.

• The washer will now be in the working status in the Normal cycle.

• If the Start/Pause button is not pressed within 5 minutes after powering on the unit

it will automatically switch off and return to the stand by mode.

• The washer will also return to the stand by mode immediately after completion of

the wash process.

• Regardless of the settings by pressing the power on/off button all programs will

stop and return to the stand by mode.

• The washer has intelligent wash resumption. If the power was interrupted at the

power source and then when the power is resumed the washer will resume

working at the stopped position.

2. Selection of Cycles

• When the washer is powered on the Normal cycle is the default cycle. If other

cycle is required press the cycle button for desired program.

3. Process Select

• Once the power is switched on the washing machine will automatically set the

Normal cycle which will Wash, Rinse and Spin. If other selection combinations

are desired, press the Process Select button to choose.

Note: Spin shall begin after some time even if there is no water in the tub. Do not

use soak process for woolen clothes. Clothes prone to fading should be

washed separately.

4. Load Size

• After Wash Cycle selection press the Load Size button to select the proper water

level for wash.

Note: See chart below for Load Size selection.

5. Speed Wash/Spin

• Once the power is switched on the machine will automatically set to Normal/Fast.

Press button to change selection. (See page 5)

8

English

Process Selecting

Note: Follow chart below for selection of wash process.

Selected Processes Applications Operation (the on indicator

represent the processes to run)

0 Wash,Rinse, Common clothes needing

Spin wash,rinse & spin

1 Wash (Wash water Repeatedly use the

remains in the tub) wash water

2 Wash,rinse(Rinse Water Repeatedly use the

remains in the tub) rinse water

3 Rinse, Spin When rinse and spin

are needed after hand wash

4 2nd rinse When the clothes

need

5 Wash, Rinse second

2nd Rinse/Spin rinse

6 Spin When only spin is needed

(to spin after drain) after hand wash

(first drain and then spin)

7 Soak, Wash, For heavily soiled clothes

Rinse, Spin shirt cuffs and collars,

first soak and then wash

0

1

2

3

/

4

5

/

Times of pressing

Process(Normal,

Heavy and Cotton

Times of pressing

Process(Quick Wash,

Delicate Casual or

Hand Wash

Water level water quantity

The Capacity of Water Water

Washing(lbs.) Level Quantity

17.6~22 10 About 23.6g

9 About 21.7g

13.2~17.6 8 About 19.3g

7 About 17.6g

8.8~13.2 6 About 16.0g

5 About 14.2g

4.4~8.8 4 About 12.5g

3 About 11.0g

Below 4.4 2 About 9g

1 About 7.3g

9

English

6. Soil Level

• When the washer is powered the machine will automatically set at Normal. Select

different soil levels by pressing button.

7. Temperature Wash/Rinse

• Initial setting is Warm/Cold when washer is powered on. Press button to change

selection based on clothes put in the washer.

8. Cycle Signal

• This is set at Low when washer is started. Press button to adjust.

9. Delay Start

• To start the washer at a later lime press the Delay Start button and set the time.

• When activated the indicator displays 2. Push button once for every 1 hour delay

for up to 24 hours

• Press Start button to activate Delay Start.

• When the delay timer starts the program select indicator turns off. The indicator

will display the remaining time to turn on the unit. In the lower right corner of the

display, a blinking light will indicate that Delay Start has been activated.

• By pressing the Delay/Start button the selected Process programs will be

displayed.

• By altering the running program, the washer will have to be reset.

10. Start/Pause

• Press this button when you want the machine to start.

• During operation press this button to pause and press it again to resume opera-

tion.

Note: By opening the top lid will stop the machine except for water filling or

draining.

10

English

Note: Total time may be affected by water inlet and drain time. It may also be

affected by the water pressure. Normal, Heavy and Cotton programs could

combine the process of soak during which the washing machine first soak

for about 20-30 minutes with slight agitation after water filling and then

begins to wash.

Loading the Washer:

• Load each item loosely.

• Separate the white and colored clothes. Separate heavy clothes from light clothes.

• Carefully check all pockets and cuffs for small items.

They can easily slide in to the tub and may damage the tub.

• Pre-treat all stains and heavily soiled areas for best results.

• Do not overload your washer.

• When loading wet items, keep water level high enough so items

can float easily in the water.

• Avoid wrapping large items such as bed sheets around the agitator.

• Close the door properly after loading the clothes. If you keep the lid

up, the agitation will not start.

Proper Use of Detergent:

• It is good washing practice to add the detergent to the water

before you add the clothes so that the detergent can work

effectively on your clothes.

Note: You can use less or more detergent depending on the size of the load, water

type in your living area, whether it is soft or hard and whether the clothes

are heavily soiled or lightly soiled.

Time list of each program (minute)

Program Total Time (min)

Including soak Not including soak

Cottons About 75-81 About 45-51

Heavy About 77-83 About 47-53

Normal About 59-69 About 39-49

Quick Wash About 25

Delicate About 36-42

Hand wash About 38-44

11

English

Fabric Softener Dispenser:

• The fabric softener dispenser is located on the top of the agitator.

Dispenser will automatically release liquid fabric softener at proper time during

rinse cycle.

Steps to use the dispenser:

1. Pour in liquid fabric softener into dispenser as recommended

by the manufacturer.

2. Add water up to its fill level, but do not exceed the level.

Warning: • Never pour fabric softener directly onto clothes because it will stain

your clothes or you may get spots on your clothes.

• Do not stop washer during its first spin or dispenser will automatically

release the softener in to the wash load.

• Do not use powder form of softener into dispenser otherwise it will

clog up the dispenser. This dispenser is only designed for liquid form.

fabric softener dispenser

12

English

Bleach Dispenser:

• Bleach dispenser is located on front corner under the loading door.

• Pour in recommended amount of bleach into dispenser

during the first wash fill.

Note: Use only liquid bleach in dispenser.

Warning: • Be careful not to spill undiluted bleach on the washer cabinet or your

clothes. As it is a strong chemical, it may damage some of your

clothes or the finish of the washer if not properly diluted.

• Use the manufacturer’s chart, on product container for recommended

use of liquid or powder bleach.

Normal Operating Sounds

The following sounds are normally heard during the

operation of the washer:

• Tumbling sounds: This is normal as the heavy wet clothes in the Washer

are continuously being tossed around.

• Air rushing noise: This happens when the Washer tub spins at

very high RPM.

• Wash and Rinse cycles going on and off will also make clicking sounds.

13

English

Lint Filter

• The lint filter must be used during washing.

• It must be cleaned in time after each using.

1. Take off the lint filter.

Pull up the lint filter from the agitator.

2. Remove lint

Press the lint screen clip with your thumb and index finger, and get the screen

downward as shown in figure below. While wet, remove the lint from the screen.

3. Install the lint filter

After cleaning, install the screen back onto the lint filter. Then put the lint filter

back in the agitator barrel.

Safety Lid Switch

• If for any reason you open the lid in the middle of the wash cycle, the

washer will not spin and will shut off automatically. Once the lid is

closed, the washer will start back on.

14

English

Warning: Always unplug your washer to avoid electric shock before cleaning.

Ignoring this warning may result in death or injury. Before using

cleaning products, always read and follow manufacturer’s instructions

and warnings to avoid personal injury or product damage.

Cleaning and Maintenance

• Use only damp or sudsy cloth for cleaning control panel.

• To avoid any kind of damage to cabinet finish, wipe washer cabinet as

needed. If you spill liquid/powdered softener, bleach or detergent on the

cabinet, wipe cabinet immediately because it can damage the finish.

• Do not use any abrasive, harsh chemicals, ammonia, chlorine bleach,

concentrated detergent, solvents or metal scouring pads. Some of these

chemicals may dissolve, damage and/or discolor your washer.

• Remove pins or other sharp objects from clothes to prevent scratching of

interior parts.

• Leave lid open after you are done washing to allow inside of washer to

dry and prevent bad odors.

Care and Cleaning Guide

English

15

Moving & Vacationing

•Turn off water supply faucet's and disconnect hoses. Drain water from all hoses.

This will prevent from damaging due to water leakage if the hoses accidentally

get ruptured or they become loose.

• Disconnect electrical plug.

• Dry inner wash tub. If moving washer, disconnect drain hose.

• Turn the leveling legs clockwise all the way in.

• Move and store your washer in upright position only.

• To prevent mold or mildew, leave lid open so moisture inside

machine can evaporate.

Storage of Your Washer in Cold Environment

• The Washer must be stored at room temperature.

• If you just got delivery of a washer when outside temperature is below freezing,

do not operate until washer has warmed to room temperature.

• Do not install or operate your washer where room temperature is below freezing.

16

English

Washer does not operate:

• Check if unit is plugged in. The plug may have come loose.

• Check if the electrical wall receptacle is of proper voltage.

• Check if the circuit breaker needs to be reset or if the fuse

needs to be replaced.

• Check if the washer is overloaded: load may need to be

re-balanced and clothes may need to be redistributed.

• Check if the lid is open. You may have to close the lid properly.

• The washer pauses in some cycles. This is normal in delicate or

hand-washable cycle, which has short soak period where your clothes

are being soaked for very short period of time. You will not hear washer

operation for a short period of time. When the soak time is over,

it will start automatically.

Problems with water:

• Not enough water coming out: Water faucet may need to be turned on

fully. Water hoses may be tangled up or wrinkled up. Straighten up

hoses. Check water level selection, it may need to be readjusted.

• Water Temperature is incorrect: Check your water heater temperature.

Hot water needs to be at a temperature at least 120˚F. -140˚F

(49˚C – 60˚C.). Check to make sure the inlet hoses are properly

connected. (e.g. hot to hot & cold to cold)

• Water leaks: This is due to not properly installing drain hose or fill

hoses. Your home drain may be clogged or having constant

water pressure. You may need to tighten hoses, check the

plumbing or call a plumber.

• Water will not drain: This is due to not installing your drain hose

properly. You may need to connect the drain hose properly. Check the

position of the drain hose. In order to drain properly, make sure that top

of drain outlet is less than 4 ft. (1.2 m) above the floor.

Troubleshooting

17

English

Washer is making noise:

• Washer may need to be reinstalled. (Check washer installation section)

• Washer load may need to be re-balanced, as the load may be uneven.

• Coins, loose change, buttons or other heavy objects could make noise

(read Operating Guide – Normal Operating Sounds).

• Squealing Sound: Due to overloaded wash tub.

• Vibration Noise: Due to not leveling washer properly on the floor and

uneven distribution of clothes in the tub.

Problems with clothes:

• Clothes are too wrinkled: this is due to improper sorting, overloading

and washing in too hot water repeatedly. Avoid overloading and resort

your load. Do not mix heavy clothes such as work clothes with light

clothes such as blouses, light shirts and delicate items. You may need to

wash in warm or cold water.

• Have soap residue: detergent may not be dissolving in water.

Check water temperature or you need to add detergent as wash

tub is being filled with water before you load your clothes to avoid

soap residue on clothes.

• Spots or stains on your clothes: this is due to incorrect use of fabric

softener. You may need to read proper instructions on the container

and follow proper directions for using the softener.

• Clothes are grayed or yellowed: this is due to not pouring

enough detergent for large loads. You may have to add more

detergent to the load.

• Clothes are ripped & have holes/excessive wear & tear: this is due to

sharp objects such as pins and belt buckles left in pockets. You will need

to remove small loose sharp objects. Fasten belts, zippers, metal snaps

etc. Check if you are using undiluted bleach. Never add undiluted

bleach to wash.

Note:

T

rouble Codes Reason

E0 Top lid not closed during delay start sequence

E1 Blockage of drain hose

E2 Top lid not closed during wash operation

18

English

INSTALLATION INSTRUCTIONS

Tools and Materials Required

You will need to have following tools to help

you in the installation of your Washer:

• Pliers

• Wrench

• Tape Measure

• Gloves

• Level

Accessories Supplied Quantity

1. Hot & Cold water inlet hoses 2

2. Drain Hose Hook 1

3. Drain Hose Clamp 1

4. Outer Drain Hose 1

5. Flat Water Inlet Hose Washers 4

1

2

3

4

5

19

English

Unpacking Your Washer

• Remove all packing materials. This includes the foam base and all

adhesive tape holding the washer accessories inside and outside.

• Open the top lid to remove the styrofoam drum brace. Pull to remove.

Note: Save drum brace. Reinstall when moving the washer.

• Inspect and remove any remains of packing, tape or printed

materials before using the washer.

Leveling Your Washer

• Your washer has 4 leveling legs; which are located on the four bottom

corners. After properly placing your washer in its final position, you can

level your washer.

• Leveling legs can be adjusted by turning them counterclockwise to raise

your washer or turning them clockwise to lower your washer.

Warning: Leveling of washer is very important to prevent vibration

during spin.

La page est en cours de chargement...

Haier ESL-T21 Manuel utilisateur

Ce manuel convient également à

Haier ESL-T21 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents