ESAB QRC-3000LS QRC-3000IO Ultrasonic Nozzle Cleaning Station Manuel utilisateur

50

60

Hz

1

PHASE

GTAW

SMAW

INVERTER

CC

DC

115

V

230

V

ULTRASONIC NOZZLE

CLEANING STATION

English

Français

Español

Revision: A Issue Date: October 27, 2008 Manual No: QRC-3000

Safety and Operating

Instructions

QRC-3000LS

QRC-3000IO

We appreciate your business!

Congratulations on your new Tweco

®

Robotics product. We are proud

to have you as our customer and will strive to provide you with the

best service and reliability in the industry. This product is backed by

our extensive warranty and worldwide service network. To locate your

nearest distributor or service agency, please contact a representative

at the address and phone number in your area listed on the back cover

of this manual, or visit us on the web at www.tweco.com.

This Operating Manual has been designed to instruct you on the correct

use and operation of your Tweco

®

Robotics product. Your satisfaction

with this product and its safe operation is our ultimate concern.

Therefore, please take the time to read the entire manual, especially

the Safety Precautions. They will help you to avoid potential hazards

that may exist when working with this product.

you are in GooD coMpany!

The Brand of Choice for Contractors and Fabricators

Worldwide.

Tweco

®

Robotics is a Global Brand of Welding Products for Thermadyne

Industries Inc. We manufacture and supply to major welding industry

sectors worldwide including; Manufacturing, Construction, Mining,

Automotive, Aerospace, Engineering, Rural and DIY/Hobbyist.

We distinguish ourselves from our competition through market-

leading, dependable products that have stood the test of time. We

pride ourselves on technical innovation, competitive prices, excellent

delivery, superior customer service and technical support, together

with excellence in sales and marketing expertise.

Above all, we are committed to develop technologically advanced

products to achieve a safer working environment within the welding

industry.

50

60

Hz

1

PHASE

GTAW

SMAW

INVERTER

CC

DC

115

V

230

V

WARNING

Read and understand this entire Manual and your employer’s safety practices

before installing, operating, or servicing the equipment. While the information

contained in this Manual represents the Manufacturer’s judgement, the

Manufacturer assumes no liability for its use.

Ultrasonic Nozzle Cleaning Station

Safety and Operating Instructions

Part Number: QRC-3000

Published by:

Thermadyne

®

Industries, Inc.

2800 Airport Rd.

Denton, TX 76207

(940) 566-2000

www.tweco.com

U.S. Customer Care: (800) 426-1888

International Customer Care: (905) 827-9777

Reproduction of this work, in whole or in part, without written permission of the publisher is

prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any loss or damage

caused by any error or omission in this Manual, whether such error results from negligence, accident,

or any other cause.

Publication Date: October 27, 2008

Record the following information for Warranty purposes:

Where Purchased:

Purchase Date:

Equipment Serial #:

Table of Contents

SECTION 1: INTRODUCTION ..................................................................................1-1

1.01 How to Use this Manual ................................................................

1-1

1.02 Receipt of Equipment ....................................................................

1-1

1.03 Description ....................................................................................1-1

SECTION 2: SAFETY PRECAUTIONS .....................................................................

2-3

SECTION 3: SPECIFICATIONS ................................................................................3-6

3.01 Power ............................................................................................3-6

3.02 Overall Dimensions .......................................................................

3-6

3.03 Tank Dimensions ...........................................................................

3-6

3.04 Material .........................................................................................3-6

SECTION 4: COMPONENT LAYOUT ........................................................................

4-7

SECTION 5: INSTALLATION AND SETUP ................................................................5-9

5.01 QRC-3000LS - Limit Switch Activated ...........................................5-9

5.02 QRC-3000IO - I/O Controlled .......................................................5-11

SECTION 6: MAINTENANCE .................................................................................

6-13

SECTION 7: PARTS LIST ...................................................................................... 7-14

SECTION 8: STATEMENT OF WARRANTY ............................................................

8-15

1-1

QRC-3000

safety and Operating instructiOns

SECTION 1:

INTRODUCTION

1.01 HOW TO USE THIS MANUAL

Information necessary to perform maintenance and service is contained in this manual. This

information is intended for use by technicians or personnel qualiﬁed to repair and service this

equipment. The information contained in this document, including performance speciﬁcations,

is subject to change without notice. To ensure safe operation, read the entire manual, including

the chapters on safety precautions and warnings.

Throughout this manual, the words WARNING, CAUTION, and NOTE may appear. Pay particular

attention to the information provided under these headings. These special annotations are

easily recognized as follows:

NOTE

NOTE conveys installation, operation, or maintenance information which is

important but not hazard-related.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, may

result in injury.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

1.02 RECEIPT OF EQUIPMENT

When you receive the equipment, check it against the invoice to make sure it is complete and

inspect the equipment for possible damage due to shipping. If there is any damage, notify the

carrier immediately to ﬁle a claim. Furnish complete information concerning damage claims

or shipping errors to the location in your area, listed on the back cover of this manual. Include

a full description of the parts in error.

If you want additional or replacement copies of this CD, please contact Tweco® Robotics at

the address and phone number in your area listed on the back cover of this manual. Include

the Manual number (from page i) and CD part number: CDROBOTICS.

1.03 DESCRIPTION

During welding, spatter accumulates on the shielding nozzle and consumables (contact tip,

diffuser). If this spatter is not removed, it will accumulate until the shielding gas is disrupted

causing inadequate gas coverage and porosity in the weld seam. The cleaning station helps

remove and prevent the build up of spatter.

How it works:

The robot moves the gun into the tank ﬁlled with anti-spatter ﬂuid and activates the ultrasonic

generator which makes the Piezo transducers vibrate the tank at a high frequency. The vibrating

waves spread throughout the liquid in the tank. When they reach the surface of the weld

consumables, they form compression and decompression waves that create micro-bubbles

(cavitation), which implode. This phenomenon triggers a mechanical action that breaks the

Introduction

1-2

safety and Operating instructiOns

QRC-3000

bond of the weld spatter at the molecular level. This breaks the bond of the spatter from the

nozzle as well as the gas diffuser and tip. It also cools down all the components. The robot

then removes the gun from the tank and a blast of air is pulsed through the gun and out the

gas diffuser. This further removes any loose spatter and excessive ﬂuid. The nozzle, tip and

diffuser are cleaned, cooled and ready to continue welding.

This process has many advantages over conventional nozzle reamers:

Cools, cleans and extends consumable life

Non-contact and no moving parts

Cleans all types and sizes of nozzles

Automatic ﬂuid dispensing

Limit switch activated or robotic I/O controlled

Eliminates programming nozzle to reamer blade

Shop air is not required for operation

Uses standard 120VAC power

The ﬂuid level in the tank is automatically maintained with a peristaltic pump and ﬂoat switch.

The pump pumps the ﬂuid from standard anti-spatter containers. The container can be placed

on the shelf on the optional stand.

This unit has a two year warranty.

•

Introduction

2-3

QRC-3000

safety and Operating instructiOns

SECTION 2:

SAFETY PRECAUTIONS

WARNING

SERIOUS INJURY OR DEATH may result if welding and cutting equipment is

not properly installed, used, and maintained. Misuse of this equipment and other

unsafe practices can be hazardous. The operator, supervisor, and helper must read

and understand the following safety warnings and instructions before installing

or using any welding or cutting equipment, and be aware of the dangers of the

welding or cutting process. Training and proper supervision are important for a

safe work place. Keep these instructions for future use. Additional recommended

safety and operating information is referenced in each section.

WARNING

This product contains chemicals, including lead, or otherwise produces

chemicals known to the State of California to cause cancer, birth defects and

other reproductive harm. Wash hands after handling.

(California Health & Safety Code § 25249.5 et seq.)

ELECTRIC SHOCK CAN CAUSE INJURY OR DEATH

Install and maintain equipment in accordance with the National Electrical Code

(NFPA 70) and local codes. Do not service or repair equipment with power on.

Do not operate equipment with protective insulators or covers removed. Service

or repair to equipment must be done by qualiﬁed and/or trained personnel only.

Do not contact electrically live parts. Always wear dry welding gloves that are in

good condition. Aluminized, protective clothing can become part of the electrical path. Keep oxygen

cylinders, chains, wires, ropes, cranes, and hoists away from any part of the electrical path. All

ground connections must be checked periodically to determine if they are mechanically strong,

and electrically adequate for the required current. When engaged in AC welding/cutting under

wet conditions or where perspiration is a factor, the use of automatic controls for reducing the

no load voltage is recommended to reduce shock hazards. Accidental contact must be prevented

when using open circuit voltage exceeding 80 volts AC, or 100 volts DC by adequate insulation

or other means. When welding is to be suspended for any length of time, such as during lunch or

overnight, all electrode holders and electrodes should be removed from the electrode holder and

the power supply should be turned off to prevent accidental contact. Keep MIG-Guns, electrode

holders, Tig torches, Plasma torches, and electrodes away from moisture and water. See safety

and operating references 1, 2, and 8.

SMOKE, FUMES, AND GASES CAN BE DANGEROUS TO YOUR HEALTH

Ventilation must be adequate to remove smoke, fumes, and gases during operation

to protect operators and others in the area. Vapors of chlorinated solvents can form

the toxic gas “Phosgene” when exposed to ultraviolet radiation from an electric arc.

All solvents, degreasers, and potential sources of these vapors must be removed

from the operating area. Use air-supplied respirators if ventilation is not adequate

to remove all fumes and gases. Oxygen supports, and vigorously accelerates ﬁre and should never

be used for ventilation. See safety and operating references 1, 2, 3, and 4.

Safety Precautions

2-4

safety and Operating instructiOns

QRC-3000

ARC RAYS, HOT SLAG, AND SPARKS CAN INJURE EYES AND BURN SKIN

Welding and cutting processes produce extreme localized heat and strong

ultraviolet rays. Never attempt to weld/cut without a federally compliant welding

helmet with the proper lens. A number 12 to 14 shade ﬁlter lens provides the

best protection against arc radiation. When in a conﬁned area, prevent the

reﬂected arc rays from entering around the helmet. Approved shielding curtains

and appropriate goggles should be used to provide protection to others in the surrounding area.

Skin should be protected from arc rays, heat, and molten metal. Always wear protective gloves

and clothing. All pockets should be closed and cuffs sewn shut. Leather aprons, sleeves, leggings,

etc. should be worn for out-of-position welding and cutting, or for heavy operations using large

electrodes. Hightop work shoes provide adequate protection from foot burns. For added protection,

use leather spats. Flammable hair preparations should not be used when welding/cutting. Wear

ear plugs to protect ears from sparks. Where work permits, the operator should be enclosed in

an individual booth painted with a low reﬂective material such as zinc oxide. See safety and

operating references 1, 2, and 3.

WELDING SPARKS CAN CAUSE FIRES AND EXPLOSIONS

Combustibles reached by the arc, ﬂame, ﬂying sparks, hot slag, and heated

materials can cause ﬁre and explosions. Remove combustibles from the work

area and/or provide a ﬁre watch. Avoid oily or greasy clothing as a spark may

ignite them. Have a ﬁre extinguisher nearby, and know how to use it. If welding/

cutting is to be done on a metal wall, partition, ceiling, or roof, precautions must

be taken to prevent ignition of nearby combustibles on the other side. Do not

weld/cut containers that have held combustibles. All hollow spaces, cavities, and containers

should be vented prior to welding/cutting to permit the escape of air or gases. Purging with inert

gas is recommended. Never use oxygen in a welding torch. Use only inert gases or inert gas

mixes as required by the process. Use of combustible compressed gases can cause explosions

resulting in personal injury or death. Arcing against any compressed gas cylinder can cause

cylinder damage or explosion. See safety and operating references 1, 2, 5, 7, and 8.

NOISE CAN DAMAGE HEARING

Noise from the air carbon-arc process can damage your hearing. Wear protective

hearing devices to ensure protection when noise levels exceed OHSA standards.

Adequate hearing protection devices must be worn by operators and surrounding

personnel to ensure personal protection against noise. See safety and operating

references 1, 2, and 6.

SAFETY AND OPERATING REFERENCES

1. Code of Federal Regulations (OSHA) Section 29, Part 1910.95, 132, 133, 134, 139, 251,

252, 253, 254 and 1000. U.S. Government Printing Ofﬁce, Washington, DC 20402.

2. ANSI Z49.1 “Safety in Welding and Cutting”.

3. ANSI Z87.1 “Practice for Occupational and Educational Eye and Face Protection”.

4. ANSI Z88.2. “Standard Practice for Respiratory Protection”. American National

Standards Institute, 1430 Broadway, New York, NY 10018.

5. AWS F4.1. “Recommended Safe Practices for Welding and Cutting Containers”.

Safety Precautions

2-5

QRC-3000

safety and Operating instructiOns

6. AWS C5.3. “Recommended Practices for Air Carbon-Arc Gouging and Cutting”.

The American Welding Society, 550 NW Lejeune Rd., P.O. Box 351040, Miami, FL

33135.

7. NFPA 51B. “Fire Prevention in Cutting and Welding Processes”.

8. NFPA-7. “National Electrical Code”. National Fire Protection Association, Battery Park,

Quincy, MA 02269.

9. CSA W117.2. “Safety in Welding, Cutting and Allied Processes”. Canadian Standards

Association, 178 Rexdale Blvd., Rexdale, Ontario, Canada M9W 1R3.

Before installation or operation of the Ultrasonic Nozzle Cleaning Station, please read and

understand all safety precautions listed below. Failure to follow these instructions may result

in personal injury or damage to the equipment.

Only qualiﬁed persons should install, operate, maintain and repair this unit.

Do not remove or deface warning and instruction labels from the unit.

Ensure that all equipment in the area is disabled and locked out before setting up,

adjusting or conducting any work.

Ensure that electrical and pneumatic power to the unit is off before setting up, adjusting,

or conducting any work.

Check that electrical and pneumatic connections comply with the codes applicable to

your country and state.

Keep hands away from the unit while it is in operation. Never put your hands or any body

part into the cleaning solution when the cleaner is on.

Use only recommended ﬂuid. Never use ﬂammable or acidic cleaning ﬂuids.

The cleaning solution may become hot. Use caution when handling ﬂuid.

For additional safety information, please refer to the following publications:

ANSI Standard Z49.1, SAFETY IN WELDING AND CUTTING

American Welding Society, 550 LeJeune Rd. P.O. Box 351040, Miami, Fl 33126

ANSI STANDARD, SAFETY FOR ROBOTS AND ROBOT SYSTEMS

American National Standards Institute, 1430 Broadway , New York, NY 10018

NFPA STANDARD 70. NATIONAL ELECTRIC CODE

National Fire Protection Association, Batterymarch Park, Quincy, MA 02269

OSHA 29 CFR 1910, SAFETY AND HEALTH STANDARDS

Superintendent of Documents, U.S. Government Printing Ofﬁce, Washington, D.C. 20402

•

Safety Precautions

3-6

safety and Operating instructiOns

QRC-3000

SECTION 3:

SPECIFICATIONS

3.01 POWER

Input Voltage 120VAC

Input Amperage 3 Amps

Frequency 50/60HZ

Fuse Size 5 Amps

Transducer Power 300 Watts Peak

Power Cord Length 25 ft. (7.5 m)

3.02 OVERALL DIMENSIONS

Height 15" (38 cm)

Width 9" (22.8 cm)

Length 10" (25.4 cm)

Weight 18.5 lb (6.4 kg)

3.03 TANK DIMENSIONS

Volume 1/2 gal. (1.89 L)

Depth 5" (12.7 cm)

Width 5" (12.7 cm)

Length 6" (15.2 cm)

3.04 MATERIAL

Tank 16 gauge 316L Stainless Steel

Enclosure 20 gauge 316L Stainless Steel

NOTE

Speciﬁcations subject to change without notiﬁcation.

Speciﬁcations

4-7

QRC-3000

safety and Operating instructiOns

SECTION 4:

COMPONENT LAYOUT

Figure 1: Isometric Views; shown with optional stand

ACTIVATING

SWITCH

Figure 2: Top View

Component Layout

4-8

safety and Operating instructiOns

QRC-3000

Component Layout

CLEANER ACTIVATION

INDICATOR

PUMP ON INDICATOR

™

Figure 3: Front View

FLUID PUMP

FLUID

IN

FLUID

OUT

PUMP WITH

COVER

FLUID INLET

(TO ANTI-SPATTER

CONTAINER)

Figure 4: Rear View

5-9

QRC-3000

safety and Operating instructiOns

SECTION 5:

INSTALLATION AND SETUP

5.01 QRC-3000LS - LIMIT SWITCH ACTIVATED

INSTALLATION

1. Place the cleaning station on a secure surface by using optional location plate or

fabricating a simple guide bracket from an angle iron. If using the optional stand,

mount it to the ﬂoor using appropriate anchors.

2. Fill tank with anti-spatter ﬂuid to the bottom of the ﬂoat guard.

3. Connect supplied 10 ft. hose to pump inlet. (See Figure 4)

4. Drill a small hole in the cap/lid of the anti-spatter container or remove cap/lid.

Place other end of hose into the anti-spatter container (cut hose to length).

5. Plug unit into a grounded 120VAC receptacle.

6. Red “PUMP ON” light should come on indicating that the pump is ﬁlling the tank to

the proper level. This may take several minutes. The pump is self priming.

7. Once “PUMP ON” light turns off, manually move the activating switch until “CLEANER

ACTIVATED” light turns on.

The system is now ready for the robot to be programmed.

ROBOT PROGRAMMING

1. Install new consumables and verify Tool Center Point is deﬁned accurately.

2. Remove nozzle.

3. Program the robot path to go above the tank then down into the tank until the ﬂuid

level is slightly below the gas holes in the gas diffuser. (See Figure 6)

Figure 5:

Insert into Cleaning Station

Figure 6:

Fluid Level below gas holes

4. Move the gun towards the activating switch until Cleaner Activate light comes on.

Move the gun an additional 1/4" further. (See Figure 7, Page 10).

Installation and Setup

5-10

safety and Operating instructiOns

QRC-3000

LIMIT SWITCH

Figure 7: Activating Switch

5. Make a wait statement for as much time as your cycle time will allow (2 to 3 second

minimum). Use ﬁne point or small zero zones for the ﬁnal position location.

6. Reverse the robot path.

7. Replace the nozzle.

8. Move the gun away from the cleaning station and program the shielding gas (purge)

or optional air-blast control to provide a burst of air to remove any excess anti-spatter

ﬂuid. Set air-blast time for 0.5 to 1.0 second. The blast can occur over a container or

while the robot travels back to the home position. DO NOT turn on the air-blast over

the cleaning station. Doing so may displace the ﬂuid in the tank!

9. Return home.

10. Test the program in Teach mode (low speed) to verify the robot path and that the

cleaner activates.

The system is now ready for production.

3

2

1

AC INPUT POWER RECEPTACLE

120VAC (L1)

2

COMMON (L2)

1

3

ULTRASONIC

3 PIN

GND

1 - GND

2 - 120VAC (L1)

3 - COMMON (L2)

Figure 8: QRC3000LS Limit Switch Control Circuit Diagram

Installation and Setup

5-11

QRC-3000

safety and Operating instructiOns

5.02 QRC-3000IO - I/O CONTROLLED

INSTALLATION

1. Place cleaning station on a secure surface

by using optional location plate or fabricating

a simple guide bracket from an angle iron. If using the optional stand, mount it to the

ﬂoor using appropriate anchors.

2. Wire interface cable (end-user supplied) to the robot controller 24VDC output, which

is located on the back of the unit above the power connector. (Figure 9)

3. Fill tank with anti-spatter ﬂuid to the bottom of the ﬂoat guard.

4. Connect supplied 10 ft. hose to pump inlet. (See Figure 4)

5. Drill a small hole in the cap/lid of the anti-spatter container or remove cap/lid.

Place other end of hose into the anti-spatter container (cut hose to length).

6. Plug unit into grounded 120VAC receptacle.

7. Red “PUMP ON” light should come on indicating that the pump is ﬁlling the tank to

the proper level. This may take several minutes. The pump is self priming.

8. Once “PUMP ON” light turns off, manually set the robot output to activate the cleaner.

“CLEANER ACTIVATED” light should turn on.

The system is now ready for the robot to be programmed.

ROBOT PROGRAMMING

1. Install new consumables and verify Tool Center Point is deﬁned accurately.

2. Remove nozzle.

3. Program the robot path to go above the tank.

4. Program the output to activate the cleaner.

5. Program the robot path so the gun goes into the tank until the anti-spatter ﬂuid level

is slightly below the gas holes in the gas diffuser. (See Figure 6, Page 9).

6. Make a wait statement for as much time as your cycle time will allow (2 to 3 second

minimum). Use ﬁne point or small zero zones for the ﬁnal position location.

7. Reverse the robot path.

8. Replace the nozzle.

9. Move the gun away from the the cleaner and program the shielding gas (purge) or

optional air-blast control to provide a burst of air to remove any excess anti-spatter

ﬂuid. Set air-blast time for 0.5 to 1.0 second. The blast can occur over a container or

while the robot travels back to the home position. DO NOT turn on the air-blast over

the the cleaner. Doing so may displace the ﬂuid in the tank!

10. Return home.

11. Test the program in Teach mode (low speed) to verify the robot path and that the

cleaner activates.

The system is now ready for production.

Installation and Setup

5-12

safety and Operating instructiOns

QRC-3000

3

2

1

AC INPUT POWER RECEPTACLE

3

4

5

2

1

INTERFACE RECEPTACLE

+

CR

120VAC (L1)

2

24VDC @ 25mA.

COMMON (L2)

1

3

ULTRASONIC

4

1

5 PIN

3 PIN

GND

TO ROBOT

CONTROLLER

2

3

CLEANER READY

ACTIVATE CLEANER

1 - GND

2 - 120VAC (L1)

3 - COMMON (L2)

1 - 0VDC INPUT

2 - CLEANER READY (COMMON)

3 - CLEANER READY (SIGNAL)

4 - +24VDC INPUT (ACTIVATE CLEANER)

5 - NO CONNECTION

Figure 9: QRC-3000IO Limit Switch Control Circuit Diagram

ROBOT CONTROL CABINET

INTERFACE CABLE

CLEANER READY COM. (RED)

SHIELD (BARE)

CONNECT TO ROBOT OUTPUT

ACTIVATE CLEANER +24DC (BLACK)

ACTIVATE CLEANER 0VDC (WHITE)

CLEANER READY SLG.(GREEN)

Figure 10: Optional Robot Interface Cable Circuit Diagram

Installation and Setup

6-13

QRC-3000

safety and Operating instructiOns

SECTION 6:

MAINTENANCE

For optimal performance, clean tank weekly.

Use proper personal protection while handling the ﬂuid.

Make sure ﬂuid is not hot before handling!

Use a shop vacuum or plant vacuum system to clean out all the ﬂuid and spatter.

Dispose of ﬂuid in accordance with local city, state and federal requirements.

You can also use a magnet brush to periodically remove spatter.

Make sure there is enough ﬂuid remaining in the anti-spatter container to reﬁll the tank

(approximately 1/2 gallon).

The tank will reﬁll automatically in approximately one hour.

•

Maintenance

7-14

safety and Operating instructiOns

QRC-3000

SECTION 7:

PARTS LIST

Part No. Stock No. Description

QRC-3325 3500-1442 Interface Power Cable For QRC-3000IO – 5-pin, 25ft.

QRC-3350 3500-1443 Interface Power Cable For QRC-3000IO – 5-pin, 50ft.

QRC-STAND 3500-1444 Stand For QRC-3000 Series with Z-slot & TCP

QRC-SHELF 3500-1445 Shelf For Anti-Spatter Fluid (Bolts to QRC-STAND)

QRC-PLATE 3500-1446 Mounting Plate For QRC-3000 Series (no stand)

QRC-BRUSH 3500-1447 Brush Magnetic For QRC-3000 Series

Parts List

8-15

QRC-3000

safety and Operating instructiOns

Statement of Warranty

SECTION 8:

STATEMENT OF WARRANTY

LIMITED WARRANTY: THERMADYNE

®

warrants that its products will be free of defects

in workmanship or material. Should any failure to conform to this warranty appear within

the time period applicable to the THERMADYNE products as stated below, THERMADYNE

shall, upon notiﬁcation thereof and substantiation that the product has been stored, installed,

operated, and maintained in accordance with THERMADYNE’s speciﬁcations, instructions,

recommendations and recognized standard industry practice, and not subject to misuse,

repair, neglect, alteration, or accident, correct such defects by suitable repair or replacement,

at THERMADYNE

®

’s sole option, of any components or parts of the product determined by

THERMADYNE

®

to be defective.

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE.

LIMITATION OF LIABILITY:

THERMADYNE

®

shall not under any circumstances be liable for

special or consequential damages, such as, but not limited to, damage or loss of purchased or

replacement goods, or claims of customers of distributor (hereinafter the “Purchaser”) for service

interruption. The remedies of the Purchaser set forth herein are exclusive and the liability of

THERMADYNE

®

with respect to any contract, or anything done in connection therewith such as

the performance or breach thereof, or from the manufacture, sale, delivery, resale, or use of any

goods covered by or furnished by THERMADYNE

®

whether arising out of contract, negligence,

strict tort, or under any warranty, or otherwise, shall not, except as expressly provided herein,

exceed the price of the goods upon which such liability is based.

THIS WARRANTY BECOMES INVALID IF REPLACEMENT PARTS OR ACCESSORIES

ARE USED WHICH MAY IMPAIR THE SAFETY OR PERFORMANCE OF ANY

THERMADYNE PRODUCT.

THIS WARRANTY IS INVALID IF THE PRODUCT IS SOLD BY NON-AUTHORIZED

PERSONS.

This warranty is effective for the time stated in the Warranty Schedule beginning on the date

that the authorized distributor delivers the products to the Purchaser.

Warranty repairs or replacement claims under this limited warranty must be submitted by an

authorized THERMADYNE

®

repair facility within thirty (30) days of the repair. No transportation

costs of any kind will be paid under this warranty. Transportation charges to send products to

an authorized warranty repair facility shall be the responsibility of the Purchaser. All returned

goods shall be at the Purchaser’s risk and expense. This warranty supersedes all previous

THERMADYNE

®

warranties.

8-16

safety and Operating instructiOns

QRC-3000

Statement of Warranty

WARRANTY SCHEDULE

The warranty is effective below for the time stated in the Warranty Schedule beginning on the date that the authorized distributor delivers

the products to the purchaser. THERMADYNE

®

reserves the right to request documented evidence of date of purchase.

Engine Driven Welders Parts / Labor

Scout

®

, Raider

®

, Explorer™

Original Main Power Stators and Inductors 3 years / 3 years

Original Main Power Rectiﬁers, Control P.C. Boards 3 years / 3 years

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Power Switch Semi-Conductors 1 year / 1 year

Engines and Associated Components are NOT Warranted by Thermal Arc

®

, Although Most are Warranted by the Engine Manufacturer. SEE THE ENGINE

MANUFACTURERS’ WARRANTY FOR DETAILS.

See the Engine Manufacturers’ Warranty

for Details

GMAW/FCAW (MIG) Welding Equipment Parts / Labor

Fabricator

®

131, 181, 190, 210, 251, 281; Fabstar

®

4030; PowerMaster

®

350, 350P, 500, 500P; Excel-Arc

®

6045; Wire Feeders: Ultrafeed

®

, Porta-feed

®

Original Main Power Transformer and Inductor 5 years / 3 years

Original Main Power Rectiﬁers, Control P.C. Boards, Power Switch Semi-Conductors 3 years / 3 years

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Electric Motors 1 year / 1 year

GTAW (TIG) & Multi-process Inverter Welding Equipment Parts / Labor

160TS, 300TS, 400TS, 185AC/DC, 200AC/DC, 300AC/DC, 400GTSW, 400MST, 300MST, 400MSTP

Original Main Power Magnetics 5 years / 3 years

Original Main Power Rectiﬁers, Control P.C. Boards, Power Switch Semi-Conductors 3 years / 3 years

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Electric Motors 1 year / 1 year

Plasma Welding Equipment Parts / Labor

Ultima

®

150

Original Main Power Magnetics 5 years / 3 years

Original Main Power Rectiﬁers, Control P.C. Boards, Power Switch Semi-Conductors 3 years / 3 years

Welding Console, Weld Controller, Weld Timer 3 years / 3 years

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Electric Motors, Coolant Recirculators 1 year / 1 year

SMAW (Stick) Welding Equipment Parts / Labor

Dragster™ 85

Original Main Power Magnetics 1 year / 1 year

Original Main Power Rectiﬁers, Control P.C. Boards 1 year / 1 year

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Power Switch Semi-Conductors 1 year / 1 year

160S, 300S, 400S

Original Main Power Magnetics 5 years / 3 years

Original Main Power Rectiﬁers, Control P.C. Boards 3 years / 3 years

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Power Switch Semi-Conductors 1 year / 1 year

General Arc Equipment Parts / Labor

Water Recirculators 1 year / 1 year

Plasma Welding Torches 180 days / 180 days

Gas Regulators (Supplied with Power Sources) 180 days / NA

MIG and TIG Torches (Supplied with Power Sources) 90 days / NA

Replacement Repair Parts 90 days / NA

MIG, TIG and Plasma Welding Torch Consumable Items NA / NA

Gas Welding and Cutting Equipment Parts / Labor

Victor

®

Professional 5 years / NA

Oxygen Conservers 2 years / NA