LD Systems U508 BPG Manuel utilisateur

U500® SERIES

TRUE DIVERSITY WIRELESS SYSTEM

USER´S MANUAL

BEDIENUNGSANLEITUNG

MANUEL D´UTILISATION

MANUAL DE USUARIO

INSTRUKCJA OBSŁUGI

MANUALE D´USO

CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ / CONTENUTO

ENGLISH

PREVENTIVE MEASURES 3

INTRODUCTION 4

SCOPE OF DELIVERY 4

CONNECTIONS, CONTROLS AND INDICATORS 5

BELTPACK MINI-XLR PIN ASSIGNMENT 7

RECEIVER OPERATION 8

TRANSMITTER OPERATION 11

BATTERY REPLACEMENT 12

TROUBLESHOOTING 13

OPTIONAL ACCESSORIES 13

SPECIFICATIONS 14

MANUFACTURER´S DECLARATIONS 17

DEUTSCH

SICHERHEITSHINWEISE 18

EINFÜHRUNG 19

LIEFERUMFANG 19

ANSCHLÜSSE, BEDIEN- UND ANZEIGEELEMENTE 20

BELEGUNG MINI-XLR-ANSCHLUSS (TASCHENSENDER) 23

BEDIENUNG EMPFÄNGER 23

BEDIENUNG SENDER 26

BATTERIEWECHSEL 27

FEHLERSUCHE 28

OPTIONALES ZUBEHÖR 28

TECHNISCHE DATEN 29

HERSTELLERERKLÄRUNGEN 32

FRANCAIS

MESURES PRÉVENTIVES 33

INTRODUCTION 34

CONTENU DU CARTON 34

CONNECTEURS, CONTRÔLES ET INDICATEURS 35

BROCHAGE TRANSMETTEUR CEINTURE MINI-XLR 37

UTILISATION DU RÉCEPTEUR 38

UTILISATION DE L’ÉMETTEUR 41

REMPLACEMENT DES PILES 42

EN CAS DE PROBLÈME 43

ACCESSOIRES OPTIONNELS 43

CARACTÉRISTIQUES TECHNIQUES 44

DECLARATIONS 47

ESPAÑOL

MEDIDAS DE SEGURIDAD 48

INTRODUCCIÓN 49

ELEMENTOS SUMINISTRADOS 49

CONEXIONES, CONTROLES E INDICADORES 50

PINEADO DEL MINI-XLR DE LA PETACAA 53

USO DEL RECEPTOR 53

USO DEL TRANSMISOR 56

SUSTITUCIÓN DE LAS PILAS 57

SOLUCIÓN DE PROBLEMAS 58

ACCESORIOS OPCIONALES 58

CARACTERÍSTICAS TÉCNICAS 59

DECLARACIÓN DEL FABRICANTE 62

POLSKI

ŚRODKI OSTROŻNOŚCI 63

WPROWADZENIE 64

ZAKRES DOSTAWY 64

PRZYŁĄCZA, ELEMENTY OBSŁUGI I WSKAŹNIKI 65

UKŁAD STYKÓW WEJŚCIA MINI-XLR W NADAJNIKU BELTPACK 67

OBSŁUGA ODBIORNIKA 68

INSTRUKCJA NADAJNIKA 71

WYMIANA BATERII 72

WYSZUKIWANIE BŁĘDÓW 73

AKCESORIA OPCJONALNE 73

SPECYFIKACJE 74

DEKLARACJE PRODUCENTA 77

ITALIANO

MISURE PRECAUZIONALI 78

INTRODUZIONE 79

IN DOTAZIONE 79

CONNESSIONI, COMANDI E INDICATORI 80

ASSEGNAZIONE PIN BELTPACK MINI-XLR 82

USO DEL RICEVITORE 83

USO DEL TRASMETTITORE 86

SOSTITUZIONE DELLE BATTERIE 87

RICERCA ERRORI 88

ACCESSORI OPZIONALI 88

DATI TECNICI 89

DICHIARAZIONI DEL PRODUTTORE 92

ENGLISH

You‘ve made the right choice!

We have designed this product to operate reliably over many years. LD Systems stands for this with its name and many years of experience as a

manufacturer of high-quality audio products. Please read this User‘s Manual carefully, so that you can begin making optimum use of your

LD Systems product quickly.

You can nd more information about LD-SYSTEMS at our Internet site WWW.LD-SYSTEMS.COM

PREVENTIVE MEASURES

1. Please read these instructions carefully.

2. Keep all information and instructions in a safe place.

3. Follow the instructions.

4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.

5. Use the equipment only in the intended manner and for the intended purpose.

6. Use only sufciently stable and compatible stands and/or mounts (for xed installations). Make certain that wall mounts are properly installed and

secured. Make certain that the equipment is installed securely and cannot fall down.

7. During installation, observe the applicable safety regulations for your country.

8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make certain that the equipment is always installed

so that is cooled sufciently and cannot overheat.

9. Never place sources of ignition, e.g., burning candles, on the equipment.

10. Ventilation slits must not be blocked.

11. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment - in this case, observe the special

instructions noted below. Do not expose this equipment to ammable materials, uids or gases. Avoid direct sunlight!

12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers lled with liquids, such as vases or drinking

vessels, on the equipment.

13. Make certain that objects cannot fall into the device.

14. Use this equipment only with the accessories recommended and intended by the manufacturer.

15. Do not open or modify this equipment.

16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.

17. During transport, make certain that the equipment cannot fall down and possibly cause property damage and personal injuries.

18. If your equipment is no longer functioning properly, if uids or objects have gotten inside the equipment or if it has been damaged in another way,

switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by authorized, qualied

personnel.

19. Clean the equipment using a dry cloth.

20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/cardboard.

21. Plastic bags must be kept out of reach of children.

FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS

22. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to an outlet with a protective ground.

Never deactivate the protective ground of a power cord.

23. If the equipment has been exposed to strong uctuations in temperature (for example, after transport), do not switch it on immediately.

Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room temperature.

24. Before connecting the equipment to the power outlet, rst verify that the mains voltage and frequency match the values specied on the

equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains

power values match. If the included power cord or power adapter does not t in your wall outlet, contact your electrician.

25. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the mains outlet and/or power adapter

and the equipment connector.

26. When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. Always disconnect the equip-

ment from the power supply if the equipment is not in use or if you want to clean the equipment. Always unplug the power cord and power adapter

from the power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands.

27. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this can shorten the useful life of the

equipment.

28. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repeatedly, please contact an authorised

service centre.

29. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter from the power outlet.

30. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be unlocked before it can be removed.

However, this also means that the equipment can slide and fall down if the power cable is pulled, which can lead to personal injuries and/or other

damage. For this reason, always be careful when laying cables.

31. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.

3

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

CAUTION:

To reduce the risk of electric shock, do not remove cover (or back). There are no user serviceable parts inside.

Maintenance and repairs should be exclusively carried out by qualied service personnel.

The warning triangle with lightning symbol indicates dangerous uninsulated voltage inside the unit, which may cause an electrical shock.

The warning triangle with exclamation mark indicates important operating and maintenance instructions.

Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot during operation. After use, wait for a

cool-down period of at least 10 minutes before handling or transporting the device.

CAUTION! HIGH VOLUMES IN AUDIO PRODUCTS!

This device is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively applicable national accident

prevention rules and regulations. As a manufacturer, Adam Hall is obligated to notify you formally about the existence of potential health risks.

Hearing damage due to high volume and prolonged exposure: When in use, this product is capable of producing high sound-pressure levels (SPL)

that can lead to irreversible hearing damage in performers, employees, and audience members. For this reason, avoid prolonged exposure to

volumes in excess of 90 dB.

INTRODUCTION

The radio transmission systems of the LD U500 Series offer professional performance and features including the automatic channel search and the

convenient one-touch infrared synchronisation for easy set-up. With switchable RF power, pilot tone transmission, and a selection of dynamic and

condenser microphones, U500 systems deliver excellent sound with advanced dynamics.

• Wireless True Diversity UHF microphone system

• Automatic channel scan for interference-free operation

• Frequency sync via infrared technology

• Individual user name

• Pilot tone for noise-free transmission

• Adjustable squelch

• Switchable transmission power (2, 10, or 30 mW)

• Hand-held and belt pack transmitter with comfortable Gain setting

• Mechanically decoupled capsules

• High-contrast OLED graphics display

• Simultaneous operation of up to 4 systems (LDU518) /up to 6 systems (LDU508 and LDU506UK) / up to 12 systems (LDU505 and LDU506)

The use of wireless microphone systems may require a license according to country-specic regulations. Please contact your local appropriate authority

for more information.

SCOPE OF DELIVERY

Scope of delivery

LDU5xxHHC: Single receiver plus hand-held transmitter and condenser capsule (cardioid), power supply, 2 x BNC antennas, audio cable,

2 x AA batteries, carrying case, instructions

LDU5xxHHD: Single receiver plus hand-held transmitter and dynamic capsule (cardioid), power supply, 2 x BNC antennas, audio cable, 2 x AA batteries,

carrying case, instructions

LDU5xxBPH: Single receiver plus hand-held transmitter and headset (black), power supply, 2 x BNC antennas, audio cable, 2 x AA batteries, carrying

case, instructions

LDU5xxBPHH: Single receiver plus hand-held transmitter and headset (skin coloured), power supply, 2 x BNC antennas, audio cable, 2 x AA batteries,

carrying case, instructions

LDU5xxBPG: Single receiver plus hand-held transmitter and guitar cable, power supply, 2 x BNC antennas, audio cable, 2 x AA batteries,

carrying case, instructions

LDU5xxBPL: Single receiver plus hand-held transmitter and lavalier microphone, power supply, 2 x BNC antennas, audio cable, 2 x AA batteries,

carrying case, instructions

LDU5xxBPW: Single receiver plus hand-held transmitter and clip microphone for brass instruments, power supply, 2 x BNC antennas, audio cable,

2 x AA batteries, carrying case, instructions

4

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

LDU5xxHHC2: Dual receiver plus 2 x hand-held transmitter and condenser capsule (cardioid), power supply, 2 x BNC antennas, audio cable, 4 x AA

batteries, carrying case, rack kit, instructions

LDU5xxHHD2: Dual receiver plus 2 x hand-held transmitter and dynamic capsule (cardioid), power supply, 2 x BNC antennas, audio cable, 4 x AA

batteries, carrying case, rack kit, instructions

LDU5xxBPH2: Dual receiver plus 2 x hand-held transmitter and headset (black), power supply, 2 x BNC antennas, audio cable, 4 x AA batteries, carrying

case, rack kit, instructions

LDU5xxBPHH2: Dual receiver plus 2 x hand-held transmitter and headset (skin coloured), power supply, 2 x BNC antennas, audio cable, 4 x AA batteries,

carrying case, rack kit, instructions

An extensive selection of suitable LD U500 single components and accessories can be found at www.LD-SYSTEMS.COM

CONNECTIONS, CONTROLS AND INDICATORS

1

2

5

3 4

9

8

1

2

3

4

5

6

7

2

3

4

9

8

RECEIVER

1

POWER

On / Off switch. Press and hold the switch for approx. 2 seconds to turn the device on or off.

2

DISPLAY

Multi-functional OLED graphics display for displaying information such as radio frequency, radio signal level and audio signal level. Also indicates the

menu items in order to adjust system settings as desired.

3

MENU

Combined pressure rotary encoder to access the Edit menu and to select and edit individual menu items.

4

VOL

Rotary encoder to adjust the audio signal volume of the audio outputs. As soon as volume changes are made, the volume setting will be shown im-

mediately on the display (VOLUME 00 - 100). After approximately 3 seconds of inactivity, the display will automatically return to to the main screen.

5

Infrared interface for synchronising the relevant system settings of the receiver and the transmitter (e.g. transmission frequency).

6

HEADPHONE OUTPUT

6.3 mm jack socket for connecting a headphone (dual receiver only).

7

HEADPHONE VOLUME LEVEL

Drehregler zum Einstellen der Kopfhörerlautstärke (nur Doppelempfänger).

8

Device for attaching the antennas for rack installation. Remove the covers, attach the BNC adapter to the front panel and connect the BNC antenna

connectors (Fig. 11, dual receiver) to the BNC adapters on the front panel (short antenna cable and BNC adapter included). Now, the antennas can be

attached to the front of the receiver.

5

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

9

Screw holes for 19” rack mounting.

11

15

16

17

12

13 14

12

13

14

11

10

12

13

14

11

10

DC SOCKET

Low-voltage socket for the power supply of the device. (Single receiver: DC 12V Plus internal/ 500 mA, Dual receiver: DC 12 V Plus internal/ 1000 mA).

Please only use the power adapter included.

11

ANTENNA A/B

BNC antenna connector A and B. For optimal reception, please connect the supplied antenna to the connectors A and B and point them upward in

“V” formation.

12

BALANCED OUTPUT

Balanced audio output with 3-pin XLR socket.

13

UNBALANCED OUTPUT

Unbalanced audio output with 6.3 mm jack socket.

14

INSTRUMENT / LINE

Level and impedance adjustment to instruments or line inputs for the unbalanced jack output. Using a suitable tool (e.g. a ball point pen), set the

switch to the down position INSTRUMENT, when connecting the receiver to the input of an instrument amplier (guitar amplier, bass amplier) and

to the opposite position LINE, when connecting to the line input of a mixer or amplier

15

BALANCED OUTPUT MIX OUT

Balanced audio output with 3-pin XLR socket (dual receiver only, signals from channels 1 and 2 are mixed).

16

UNBALANCED OUTPUT MIX OUT

Unbalanced audio output with 6.3 mm jack socket (dual receiver only, signals from channels 1 and 2 are mixed).

17

INSTRUMENT / LINE MIX OUT

Level and impedance adjustment to instruments or line inputs for the unbalanced jack output MIX OUT (dual receiver only). Using a suitable tool

(e.g. a ball point pen), set the switch to the down position INSTRUMENT, when connecting the receiver to the input of an instrument amplier (guitar

amplier, bass amplier) and to the opposite position LINE, when connecting to the line input of a mixer or amplier.

6

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

HANDHELD TRANSMITTER

22

21

20

19

18

BELT PACK TRANSMITTER

18

24

21

22

20

19

23

18

ON / OFF

On / Off switch. Set the switch to the ON position to turn the receiver on, and to the OFF position to turn it off.

19

DISPLAY

Multi-functional OLED graphics display for displaying the frequency group and channel, the username and battery status. Also indicates the menu

items in order to adjust transmitter settings as desired.

20

Infrared interface for synchronising the relevant system settings with the receiver (e.g. transmission frequency).

21

MENU / SEL

Switch to access the Edit menu and to select individual menu items.

22

Switch to edit the individual menu options on the Edit menu.

23

ANTENNA

Interchangeable antenna of the belt pack transmitter. For optimal reception, please do not obstruct or bend (belt pack transmitter only).

24

INPUT

3-pin mini XLR socket to connect a headset, lavalier or instrument microphone, as well as a guitar cable (belt pack transmitter only).

BELTPACK MINI-XLR PIN ASSIGNMENT

1

2

3

MINI-XLR

sleeve tip

6,3 mm jack

Guitar & Bass and other high impendance sources.

7

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

1

2

ava3

MINI-XLR

Condenser with internal pull up resistor.

1

2

3

MINI-XLR

R

2,2k

Condenser without internal pull up resistor.

RECEIVER OPERATION

When operating the wireless transmission system, be sure to place the receiver in the line of sight of the transmitter. For optimal reception,

perform the automatic frequency search after switching on the receiver. Leave the corresponding transmitter off, but other radio systems turned

on, if necessary. For the operating steps, see FREQ AUTO RUN.

DISPLAY

After switching on the receiver, “WELCOME” appears for a short time, then the main screen displays the following information: individual username,

battery status, radio signal level (RF), active antenna (A / B), level of the audio signal, frequency group and channel (GR.xx and CH.xx) and the radio

frequency in MHz.

IR SYNC RUN

To synchronize the transmitter with the radio frequency set in the receiver and the individual username, bring the infrared port of the transmitter

in direct visual contact with the infrared port of the receiver (distance approx. 10 cm) and turn on the transmitter. Now press the pressure rotary

encoder of the receiver (MENU) to access the Edit menu and select the menu item IR SYNC RUN by rotating the encoder (light background). Press

again on MENU to initiate the synchronization process. After a few seconds, the process is completed and the display of the transmitter switches for

a short time to “IR SYNC ”, conrming successful synchronization. To cancel the operation, press MENU. Press briey(!) on POWER to return directly

to the main display. After about 10 seconds of inactivity, the main display is automatically shown.

FREQ AUTO RUN

Automatic frequency search (frequency scan) to determine an interference-free radio frequency in the current environment and to allow for

optimal reception. For this purpose, leave the corresponding transmitter off, but other radio systems turned on, if necessary. Press the pressure

rotary encoder (MENU) to access the Edit menu and select the menu item FREQ AUTO RUN by rotating the encoder (light background). To initiate

the process, press again on MENU. Progress is now indicated on the display by an animation and the scanning process is completed after approx. 30

seconds (to cancel, press MENU). The resulting frequency is automatically enabled and, as in “IR SYNC RUN”, you can now switch on the transmitter

and synchronize it with the receiver. Press briey(!) on POWER to return directly to the main display. After about 10 seconds of inactivity, the main

display is automatically shown.

· Individual username

· Radio signal level and active antenna

· Frequency group and channel

· Battery status of the transmitter

· Audio signal level / Peak (PK)

· Radio frequency in MHz

8

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

GROUP

Menu item to adjust the frequency group. The LD U500 wireless system has 8 frequency groups, which can be selected as desired. Press the

pressure rotary encoder (MENU) to access the Edit menu and select the menu item GROUP by rotating the encoder (light background). Press MENU

again and select one of the groups 01 to 08 by rotating the encoder. To conrm, press MENU. Pressing MENU once more will take you up one level

in the menu structure. Press briey(!) on POWER to return directly to the main display. After about 10 seconds of inactivity, the main display is

automatically shown.

CHANNEL

Menu item to adjust the frequency channel. The LD U500 wireless system has 8 frequency groups featuring 12 channels each, which can be selected

as desired. Press the pressure rotary encoder (MENU) to access the Edit menu and select the menu item CHANNEL by rotating the encoder (light

background). Press MENU again and select one of the channels 01 to 12 by rotating the encoder. To conrm, press MENU. Pressing MENU once more

will take you up one level in the menu structure. Press briey(!) on POWER to return directly to the main display. After about 10 seconds of inactivity,

the main display is automatically shown.

FREQ MAN

Manual adjustment of the radio frequency in 25 kHz increments. Press the pressure rotary encoder (MENU) to access the Edit menu and select the

menu item FREQ MAN by rotating the encoder (light background). Press MENU and adjust the frequency in the MHz range by rotating the encoder.

Press MENU again and adjust the frequency in the kHz range in 25 kHz increments by rotating the encoder. To conrm, press MENU. Pressing MENU

once more will take you up one level in the menu structure. Press briey(!) on POWER to return directly to the main display. After about 10 seconds

of inactivity, the main display is automatically shown. The display will now show U for user under group GR. and CH.1 under channel.

NAME

To clearly assign transmitters and receivers to a specic performer, you have the ability to show names, numbers, or characters on the display.

Press the pressure rotary encoder (MENU) to access the Edit menu and select the menu item NAME by rotating the encoder (light background).

Press MENU and then, as desired, select the letter, number or symbol for the rst of the 8 digits provided by rotating the encoder and conrming

with MENU; now, the second digit can be set as desired, etc.. Once the last digit has been conrmed, pressing MENU again will take you to a higher

level in the menu structure. Press briey(!) on POWER to return directly to the main display. After about 10 seconds of inactivity, the main display is

automatically shown. In addition to the radio frequency, the name is also transferred to the transmitter when synchronizing.

PILOT TONE

The pilot tone feature protects a wireless microphone system against interference of unwanted signals, for example from other radio equipment.

The transmitter adds a second inaudible signal, the pilot tone, to the signal to be transmitted. The receiver identies this as the matching pilot tone

and frees the corresponding signal. Signals without pilot tone remain muted. Press the pressure rotary encoder (MENU) to access the Edit menu and

select the menu item PILOT TONE by rotating the encoder (light background). Press again on MENU and using the encoder, select ON, for initiating

pilot tone (right turn), or OFF for pilot tone equipment switched off (turn left). To conrm, press MENU. Pressing MENU once more will take you

up one level in the menu structure. Press briey(!) on POWER to return directly to the main display. After about 10 seconds of inactivity, the main

display is automatically shown.

· Battery status of the transmitter

· Audio signal level / Peak (PK)

· Radio frequency in MHz

9

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

SQUELCH

The squelch control prevents unwanted background noise when the transmitter is turned off. In addition, sudden background noises are sup-

pressed when the signal transmitted from the transmitter to the receiver is not strong enough (for instance because of excessive distance) Set

the squelch control (with the transmitter switched off) to the lowest setting, which still effectively suppresses background noises. In unfavourable

conditions, in the “HIGH” setting, the transmission range may decrease. Press the pressure rotary encoder (MENU) to access the Edit menu and

select the menu item SQUELCH by rotating the encoder (light background). Press MENU again and select the optimum setting for your application

by rotating the encoder (LOW = low, MID= mid and HIGH = high threshold). To conrm, press MENU. Pressing MENU once more will take you up one

level in the menu structure. Press briey(!) on POWER to return directly to the main display. After about 10 seconds of inactivity, the main display is

automatically shown.

BRIGHTNESS

Menu item to adjust the brightness of the display illumination. Press the pressure rotary encoder (MENU) to access the Edit menu and select the

menu item BRIGHTNESS by rotating the encoder (light background). Press MENU again and select the optimum setting for your application by

rotating the encoder (LOW = low, MID= mid and HIGH = high brightness). To conrm, press MENU. Pressing MENU once more will take you up one

level in the menu structure. Press briey(!) on POWER to return directly to the main display. After about 10 seconds of inactivity, the main display is

automatically shown.

PANEL LOCK

To protect the receiver against accidental and unauthorised operation, it is possible to initiate an automatic locking of the controls. Press the

pressure rotary encoder (MENU) to access the Edit menu and select the menu item PANEL LOCK by rotating the encoder (light background). Press

again on MENU and using the encoder, select ON, for initiating the automatic lock (right turn), or OFF to switch it off (turn left). To conrm, press

MENU. Pressing MENU once more will take you up one level in the menu structure. Press briey(!) on POWER to return directly to the main display. If

the automatic lock is activated, after approx. 10 seconds, “DISPLAY IS LOCKED” is displayed for a short time and also if one of the controls is activated;

a change to the settings of the receiver via the control elements is then not possible. Press and hold the pressure rotary encoder for approx. 3

seconds to unlock the control elements (“DISPLAY IS UNLOCKED” is displayed for about 1 second).

EXIT

To exit the Edit menu and return to the main display, select EXIT (light background) by rotating the pressure rotary encoder and press MENU.

Alternatively, press briey(!) on POWER to return directly to the main display. After about 10 seconds of inactivity, the main display is automatically

shown.

BATTERY STATUS

The battery status of the corresponding transmitter will appear on the display and is constantly updated. When the battery is fully charged, the icon

( = approx. 70%, = approx. 30%) will appear. As soon as the icon for “low battery” is displayed, the display changes to

“LOW BATTERY” and shows approximately every 5 seconds. Replace the batteries immediately.

10

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

TRANSMITTER OPERATION

MAIN DISPLAY

After switching on the transmitter, the main screen displays the following information: username, frequency group and channel (GR.xx and CH.xx)

and battery status. Remove the battery compartment cover on the transmitter to release the controls SEL and arrow buttons (hand-held

transmitter: remove the screwable cover shell by rotating it to the left, belt pack transmitter: pull cover shell by pressing on the markings on the

sides of the housing). Now press the arrow button, and the radio frequency, gain and transmission power are displayed (back with arrow button).

GAIN

To avoid distortions and to adjust the transmitter optimally to the input audio signal, it is possible to adjust the audio levels in 3dB increments

from 0dB to -27dB. Open the battery compartment cover as previously described to reveal the controls. Press SEL to access the Edit menu and press

SEL repeatedly, if necessary, to select the menu item GAIN (light background). Now lower the audio level if necessary by repeatedly pressing the

arrow button until you have no more distortion and the peak indicator AF PK in the display of the receiver goes out (watch out for peak levels). To

exit the menu item, press SEL, call up the menu item EXIT by pressing SEL repeatedly if necessary, and conrm by pressing the arrow button. After

approximately 10 seconds of inactivity, the display will automatically return to the main screen.

RF POWER

Adjust the output power of the transmitter according to the application (recommendation: outdoors = 30mW, stage = 10mW, conference setting

= 2mW). Open the battery compartment cover as previously described to reveal the controls. Press SEL to access the Edit menu and press SEL

repeatedly, if necessary, to select the menu item RF POWER (light background). Now, using the arrow keys, select the desired output power (30mW,

10mW, 2mW - in the frequency range of 863 – 865 MHz, the output power is automatically reduced to 10 mW in accordance with legal requirements).

To exit the menu item, press SEL, call up the menu item EXIT by pressing SEL repeatedly if necessary, and conrm by pressing the arrow button. After

approximately 10 seconds of inactivity, the display will automatically return to the main screen.

EXIT

In order to exit the Edit menu and return to the main display, call up the menu item EXIT and conrm by pressing the arrow button.

After approximately 10 seconds of inactivity, the display will automatically return to the main screen.

BATTERY STATUS

The battery status of the transmitter will appear in the display and is constantly updated. When the battery is fully charged, the icon

(

= approx. 70%,

= approx. 30%) will appear. As soon as the icon for “low battery” is displayed, the display changes to “LOW BATTERY” and

shows approximately every 5 seconds. Replace the batteries immediately.

11

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

ATTACHING THE PACK TRANSMITTER

Attach the transmitter to a belt or strap as shown below.

BATTERY REPLACEMENT

Open the battery compartment of the hand-held transmitter by turning the battery compartment cover counter-clockwise and pull it from the

housing. Remove the used batteries and insert new batteries (AA, Mignon) as shown on the illustration inside the battery compartment. Replace

the battery compartment cover on the housing and close the battery compartment by turning clockwise. If the transmitter is not in use for a long

period of time, remove the batteries from the battery compartment on the transmitter to avoid damage caused by defective batteries.

Open the battery compartment of the hand-held transmitter by pressing on both markings on the sides of the battery compartment cover (Fig.

A) and pull it away until it stops. Remove the used batteries and insert new batteries (AA, Mignon) as shown on the illustration inside the battery

compartment. Slide the battery compartment cover back onto the housing until the cover clicks into place. If the transmitter is not in use for a long

period of time, remove the batteries from the battery compartment on the transmitter to avoid damage caused by defective batteries.

A

12

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

TROUBLESHOOTING

PROBLEM DISPLAY SOLUTION

No audio signal or

low level

Receiver: Reception is not displayed on antenna A or B. Verify that the transmitter is turned on.

Check the batteries in the transmitter.

Receiver: Display light is off Check the power supply in the transmitter.

Receiver: Reception is not displayed on antenna A or B.

Transmitter: Device is turned on. Charge status of the

batteries is ok.

Check whether radio frequency of transmitter and receiver

match.

Check the transmission output.

Reduce the distance between transmitter and receiver.

Make sure that there is a direct line of sight between the

transmitter and receiver.

Make sure that the antennas of the receiver are aligned

upward and into a V-shape.

Reduce the amount of noise reduction (SQUELCH)

Receiver: Neither antenna A nor antenna B LED is

displayed.

Increase the signal level or check the GAIN setting on the

transmitter.

Distortion and

interference

Receiver: Radio signal is displayed Remove possible sources of interference (digital devices,

other wireless systems).

Increase the level of noise reduction (MUTE level) on the

receiver.

Distorted sound Transmitter and Receiver: "LOW BATTERY" is displayed.

Receiver: AF PK peak indicator is displayed on the receiver

display.

Replace the batteries in the transmitter.

Increase the signal level or lower the audio level GAIN on

the transmitter.

OPTIONAL ACCESSORIES

LDU500CH - Microphone head with condenser capsule and hyper cardioid directivity (matt black)

LDU500DH - Microphone head with dynamic capsule and hyper cardioid directivity (matt black)

LDU500CC - Microphone head with condenser capsule and hyper cardioid directivity (matt silver)

LDU500DC - Microphone head with dynamic capsule and hyper cardioid directivity (matt silver)

LDU500RK - 19” rack installation kit for mounting a single receiver (2 rack brackets, 2 BNC adapters, 2 short antenna cables and 1 set of screws included).

LDU500RK2 - 19” rack installation kit for mounting a dual receiver (2 rack brackets, 2 connectors and 1 set of screws included).

13

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

MOUNTING

1 2 3

1

Screw the connectors (receiver A right, receiver B left).

2

Place both receivers together and screw into place.

3

Screw the rack brackets (receiver A right, receiver B left).

An extensive selection of suitable LD U500 wireless systems and further accessories can be found at www.LD-SYSTEMS.COM

SPECIFICATIONS

Receiver

Model name: LDU50xR LDU50xR2

Receiver type: true diversity

Modulation: FM

Frequency range: 823 - 832 MHz & 863 - 865 MHz (LDU508), 584 - 607 MHz (LDU505), 655 - 679 MHz (LDU506), 604 - 614 MHz

(LDU506UK), 1785 - 1800 MHz (LDU518)

Channels: 96 (8 x 12)

Groups: 8

Antenna connectors: 2 x BNC

Antenna Gain: 2.15 dBi

Frequency response: 30 - 16.000 Hz

Noise Reduction: adjustable squelch

THD: <0.1%

Signal-to-noise ratio: >100dB

Balanced output: XLR 2 x XLR

Balanced mix output: XLR

Unbalanced output: 6.3 mm jack 2x 6.3mm jack

Unbalanced mix output: 6.3 mm jack

14

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

Headphones output: 6.3 mm stereo jack

Audio output level (balanced): +10dBu

Audio output level

(unbalanced):

+6dBV / 0dBV (Switchable Line / Instrument)

Controls: POWER on/off, MENU push-turn-control, VOL

Volume control, switch INSTRUMENT/LINE

POWER on/off, 2x MENU push-turn-control, 2x

VOL Volume control, 2x switch INSTRUMENT/LINE,

headphones volume control

Indicators: multifunctional OLED-graphic display, 2 x multifunctional OLED-graphic display

Operating voltage: 12V DC, 500 mA 12V DC, 1000 mA

Operating temperature range: 5°C … 40°C

Relative humidity in operation: 20% … 80% (non condensing)

Dimensions (W x H x D): 212 x 44 x 159mm 484 x 44 x 200mm

Weight: 0.95kg 2.05 kg

Accessories included: power adapter, 2 x antenna, audio cable power adapter, 2 x antenna, audio cable, rack kit

Features: channel scan function, infrared frequency synchronisation, pilot tone

Handheld transmitter

Model name: LDU50xMD LDU50xMC

Modulation: FM

Frequency range: 823 - 832 MHz & 863 - 865 MHz (LDU508), 584 - 607 MHz (LDU505), 655 - 679 MHz (LDU506),

604 - 614 MHz (LDU506UK), 1785 - 1800 MHz (LDU518)

Channels: 96 (8 x 12)

Groups: 8

Microphone type: dynamic condenser

Polar pattern: cardioid cardioid

Frequency response: 60 - 16.000 Hz

THD: <0.2% @ 1kHz

Signal-to-noise ratio: >95 dB

RF output power: 2mW, 10mW, 30mW switchable and depending on the RF -Range

Antenna Gain: 0.5 dBi

Controls: Power on/off, Select, Arrow button

Indicators: multifunctional OLED-graphic display

Power supply: 2 x AA battery

Operating time: up to 10 h (depending on batteries)

Operating temperature range: 5°C … 40°C

Relative humidity range in operation: 20% … 80% (non condensing)

Dimensions (L x Ø): 257 x 51mm 257 x 50mm

Weight (without batteries): 0.2 kg 0.21kg

Accessories included: 2 x AA battery

Features: infrared frequency synchronisation

Bodypack transmitter

Model name: LDU50xBP

Modulation: FM

Frequency range: 823 - 832 MHz & 863 - 865 MHz (LDU508), 584 - 607 MHz (LDU505), 655 - 679 MHz (LDU506), 604 - 614 MHz

(LDU506UK), 1785 - 1800 MHz (LDU518)

15

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

Microphones

Model name: LDWS100MH1 LDWS100MH3 LDWS100ML LDWS1000MW

Microphone type: headset headset lavalier microphone wind instrument

microphone

Capsule: back-electret condenser back-electret condenser back-electret condenser back-electret condenser

Polar pattern: cardioid cardioid cardioid cardioid

Frequency response: 20 - 20.000 Hz 70 - 16.000 Hz 20 - 20.000 Hz 50 - 18.000 Hz

Connector: 3-pin mini-XLR 3-pin mini-XLR 3-pin mini-XLR 3-pin mini-XLR

Accessories included: foam windscreen foam windscreen foam windscreen foam windscreen

Features: skin coloured

Model name: LDU500CC LDU500DC LDU500CH LDU500DH

Microphone type: Microphone head for

U500 handheld

Microphone head for

U500 handheld

Microphone head for

U500 handheld

Microphone head for

U500 handheld

Capsule: back-electret condenser dynamic back-electret condenser dynamic

Polar pattern: cardioid cardioid hyper cardioid hyper cardioid

Connector: LDU500 screw connection LDU500 screw connection LDU500 screw connection

LDU500 screw

connection

Colour: matt silver matt silver matt black matt black

Features: low noise -FET impedan-

ce converter, customized

shock mount, gold

contacts

shock mount, gold

contacts

low noise -FET impedan-

ce converter, customized

shock mount, gold

contacts

shock mount, gold

contacts

Channels: 96 (8 x 12)

Groups: 8

Input: 3-pin mini-XLR (Low-Z/High-Z)

Frequency response: 30 - 16.000 Hz

THD: <0.1% @ 1kHz

Signal-to-noise ratio: >90 dB

RF output power: 2mW, 10mW, 30mW switchable and depending on the RF -Range

Antenna Gain: 0.5 dBi

Controls: Power on/off, Select, Arrow button

Indicators: multifunctional OLED-graphic display

Power supply: 2 x AA batteries

Operating time: up to 10 h (depending on batteries)

Operating temperature range: 5°C … 40°C

Relative humidity range in operation: 20% … 80% (non condensing)

Dimensions (W x H x D): 65 x 86 x 23 mm

Weight (without batteries): 0,09 kg

Accessories included: 2 x AA battery

Features: infrared frequency synchronisation

16

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

Guitar cable

Model name: LDU500GC

Connector 1: 3-pin mini-XLR

Connector 2: 6.3 mm jack

Length: 0.8 m

MANUFACTURER´S DECLARATIONS

MANUFACTURER‘S WARRANTY & LIMITATIONS OF LIABILITY

You can nd our current warranty conditions and limitations of liability at: https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS-DECLARA-

TIONS_LD_SYSTEMS.pdf To request warranty service for a product, please contact Adam Hall GmbH, Adam-Hall-Str. 1,

61267 Neu Anspach / Email: [email protected] / +49 (0)6081 / 9419-0.

CORRECT DISPOSAL OF THIS PRODUCT

(valid in the European Union and other European countries with a differentiated waste collection system)

This symbol on the product, or on its documents indicates that the device may not be treated as household waste. This is to avoid environ-

mental damage or personal injury due to uncontrolled waste disposal. Please dispose of this product separately from other waste and have it

recycled to promote sustainable economic activity. Household users should contact either the retailer where they purchased this product, or their

local government ofce, for details on where and how they can recycle this item in an environmentally friendly manner. Business users should

contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial waste

for disposal.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation

CE Compliance

Adam Hall GmbH states that this product meets the following guidelines (where applicable):

R&TTE (1999/5/EC) or RED (2014/53/EU) from June 2017

Low voltage directive (2014/35/EU)

EMV directive (2014/30/EU)

RoHS (2011/65/EU)

The complete declaration of conformity can be found at www.adamhall.com.

Furthermore, you may also direct your enquiry to [email protected].

EU DECLARATION OF CONFORMITY

Hereby, Adam Hall GmbH declares that this radio equipment type is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following

internet address: www.adamhall.com/compliance/

17

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

DEUTSCH

Sie haben die richtige Wahl getroffen!

Dieses Gerät wurde unter hohen Qualitätsanforderungen entwickelt und gefertigt, um viele Jahre einen reibungslosen Betrieb zu gewährleisten.

Dafür steht LD Systems mit seinem Namen und der langjährigen Erfahrung als Hersteller hochwertiger Audioprodukte. Bitte lesen Sie diese Bedie-

nungsanleitung sorgfältig, damit Sie Ihr neues Produkt von LD Systems schnell optimal einsetzen können.

Mehr Informationen zu LD SYSTEMS nden Sie auf unserer Internetseite www.LD-SYSTEMS.COM

SICHERHEITSHINWEISE

1. Lesen Sie diese Anleitung bitte sorgfältig durch.

2. Bewahren Sie alle Informationen und Anleitungen an einem sicheren Ort auf.

3. Befolgen Sie die Anweisungen.

4. Beachten Sie alle Warnhinweise. Entfernen Sie keine Sicherheitshinweise oder andere Informationen vom Gerät.

5. Verwenden Sie das Gerät nur in der vorgesehenen Art und Weise.

6. Verwenden Sie ausschließlich stabile und passende Stative bzw. Befestigungen (bei Festinstallationen). Stellen Sie sicher, dass Wandhalterungen

ordnungsgemäß installiert und gesichert sind. Stellen Sie sicher, dass das Gerät sicher installiert ist und nicht herunterfallen kann.

7. Beachten Sie bei der Installation die für Ihr Land geltenden Sicherheitsvorschriften.

8. Installieren und betreiben Sie das Gerät nicht in der Nähe von Heizkörpern, Wärmespeichern, Öfen oder sonstigen Wärmequellen. Sorgen Sie dafür,

dass das Gerät immer so installiert ist, dass es ausreichend gekühlt wird und nicht überhitzen kann.

9. Platzieren Sie keine Zündquellen wie z.B. brennende Kerzen auf dem Gerät.

10. Lüftungsschlitze dürfen nicht blockiert werden.

11. Betreiben Sie das Gerät nicht in unmittelbarer Nähe von Wasser. Bringen Sie das Gerät nicht mit brennbaren Materialien, Flüssigkeiten oder Gasen

in Berührung. Direkte Sonneneinstrahlung vermeiden!

12. Sorgen Sie dafür, dass kein Tropf- oder Spritzwasser in das Gerät eindringen kann. Stellen Sie keine mit Flüssigkeit gefüllten Behältnisse wie

Vasen oder Trinkgefäße auf das Gerät.

13. Sorgen Sie dafür, dass keine Gegenstände in das Gerät fallen können.

14. Betreiben Sie das Gerät nur mit dem vom Hersteller empfohlenen und vorgesehenen Zubehör.

15. Öffnen Sie das Gerät nicht und verändern Sie es nicht.

16. Überprüfen Sie nach dem Anschluss des Geräts alle Kabelwege, um Schäden oder Unfälle, z. B. durch Stolperfallen zu vermeiden.

17. Achten Sie beim Transport darauf, dass das Gerät nicht herunterfallen und dabei möglicherweise Sach- und Personenschäden verursachen kann.

18. Wenn Ihr Gerät nicht mehr ordnungsgemäß funktioniert, Flüssigkeiten oder Gegenstände in das Geräteinnere gelangt sind, oder das Gerät an-

derweitig beschädigt wurde, schalten Sie es sofort aus und trennen es von der Netzsteckdose (sofern es sich um ein aktives Gerät handelt). Dieses

Gerät darf nur von autorisiertem Fachpersonal repariert werden.

19. Verwenden Sie zur Reinigung des Geräts ein trockenes Tuch.

20. Beachten Sie alle in Ihrem Land geltenden Entsorgungsgesetze. Trennen Sie bei der Entsorgung der Verpackung bitte Kunststoff und Papier bzw.

Kartonagen voneinander.

21. Kunststoffbeutel müssen außer Reichweite von Kindern aufbewahrt werden.

BEI GERÄTEN MIT NETZANSCHLUSS

22. ACHTUNG: Wenn das Netzkabel des Geräts mit einem Schutzkontakt ausgestattet ist, muss es an einer Steckdose mit Schutzleiter angeschlossen

werden. Deaktivieren Sie niemals den Schutzleiter eines Netzkabels.

23. Schalten Sie das Gerät nicht sofort ein, wenn es starken Temperaturschwankungen ausgesetzt war (beispielsweise nach dem Transport). Feuch-

tigkeit und Kondensat könnten das Gerät beschädigen. Schalten Sie das Gerät erst ein, wenn es Zimmertemperatur erreicht hat.

24. Bevor Sie das Gerät an die Steckdose anschließen, prüfen Sie zuerst, ob die Spannung und die Frequenz des Stromnetzes mit den auf dem Gerät

angegebenen Werten übereinstimmen. Verfügt das Gerät über einen Spannungswahlschalter, schließen Sie das Gerät nur an die Steckdose an,

wenn die Gerätewerte mit den Werten des Stromnetzes übereinstimmen. Wenn das mitgelieferte Netzkabel bzw. der mitgelieferte Netzadapter

nicht in Ihre Netzsteckdose passt, wenden Sie sich an Ihren Elektriker.

25. Treten Sie nicht auf das Netzkabel. Sorgen Sie dafür, dass spannungsführende Kabel speziell an der Netzbuchse bzw. am Netzadapter und der

Gerätebuchse nicht geknickt werden.

26. Achten Sie bei der Verkabelung des Geräts immer darauf, dass das Netzkabel bzw. der Netzadapter stets frei zugänglich ist. Trennen Sie das Gerät

stets von der Stromzuführung, wenn das Gerät nicht benutzt wird, oder Sie das Gerät reinigen möchten. Ziehen Sie Netzkabel und Netzadapter immer am

Stecker bzw. am Adapter und nicht am Kabel aus der Steckdose. Berühren Sie Netzkabel und Netzadapter niemals mit nassen Händen.

27. Schalten Sie das Gerät möglichst nicht schnell hintereinander ein und aus, da sonst die Lebensdauer des Geräts beeinträchtigt werden könnte.

28. WICHTIGER HINWEIS: Ersetzen Sie Sicherungen ausschließlich durch Sicherungen des gleichen Typs und Wertes. Sollte eine Sicherung wiederholt

auslösen, wenden Sie sich bitte an ein autorisiertes Servicezentrum.

29. Um das Gerät vollständig vom Stromnetz zu trennen, entfernen Sie das Netzkabel bzw. den Netzadapter aus der Steckdose.

30. Wenn Ihr Gerät mit einem verriegelbaren Netzanschluss bestückt ist, muss der passende Gerätestecker entsperrt werden, bevor er entfernt wer-

den kann. Das bedeutet aber auch, dass das Gerät durch ein Ziehen am Netzkabel verrutschen und herunterfallen kann, wodurch Personen verletzt

werden und/oder andere Schäden auftreten können. Verlegen Sie Ihre Kabel daher immer sorgfältig.

31. Entfernen Sie Netzkabel und Netzadapter aus der Steckdose bei Gefahr eines Blitzschlags oder wenn Sie das Gerät länger nicht verwenden.

ACHTUNG

Entfernen Sie niemals die Abdeckung, da sonst das Risiko eines elektrischen Schlages besteht. Im Inneren

des Geräts benden sich keine Teile, die vom Bediener repariert oder gewartet werden können. Lassen Sie

Wartung und Reparaturen ausschließlich von qualiziertem Servicepersonal durchführen.

18

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

Das gleichseitige Dreieck mit Blitzsymbol warnt vor nichtisolierten, gefährlichen Spannungen im Geräteinneren, die einen elektrischen

Schlag verursachen können.

Das gleichseitige Dreieck mit Ausrufungszeichen kennzeichnet wichtige Bedienungs- und Wartungshinweise.

Warnung! Dieses Symbol kennzeichnet heiße Oberächen. Während des Betriebs können bestimmte Teile des Gehäuses heiß werden.

Berühren oder transportieren Sie das Gerät nach einem Einsatz erst nach einer Abkühlzeit von mindestens 10 Minuten.

ACHTUNG HOHE LAUTSTÄRKEN BEI AUDIOPRODUKTEN!

Dieses Gerät ist für den professionellen Einsatz vorgesehen. Der kommerzielle Betrieb dieses Geräts unterliegt den jeweils gültigen nationalen Vorschriften

und Richtlinien zur Unfallverhütung. Als Hersteller ist Adam Hall gesetzlich verpichtet, Sie ausdrücklich auf mögliche Gesundheitsrisiken hinzuweisen.

Gehörschäden durch hohe Lautstärken und Dauerbelastung: Bei der Verwendung dieses Produkts können hohe Schalldruckpegel (SPL) erzeugt werden, die

bei Künstlern, Mitarbeitern und Zuschauern zu irreparablen Gehörschäden führen können. Vermeiden Sie länger

anhaltende Belastung durch hohe Lautstärken über 90 dB.

EINFÜHRUNG

Die Funkübertragungssysteme der LD U500 Serie bieten professionelle Leistung und Funktionen einschließlich der automatischen Kanalsuche und

der bequemen One-Touch-Infrarot-Synchronisierung für einfache Einrichtung. Mit schaltbarer HF-Leistung, Pilotton-Übertragung und einer Auswahl

von dynamischen und Kondensatormikrofonen liefern U500 Systeme hervorragenden Klang mit erweiterter Dynamik.

• Drahtloses True Diversity UHF Mikrofon System

• Automatischer Kanal-Scan für interferenzfreie Funktion

• Frequenz-Sync via Infrarot-Technik

• Individueller Benutzername

• Pilot-Ton für störgeräuschfreie Übertragung

• Einstellbare Rauschsperre (Squelch)

• Schaltbare Sendeleistung (2, 10 oder 30 mW)

• Hand- und Taschensender mit komfortabler Gain-Einstellung

• Mechanisch entkoppelte Kapseln

• Kontrastreiches OLED-Grakdisplay

• Simultaner Betrieb von bis zu 4 Systemen (LDU518) / bis zu 6 Systemen (LDU508 und DU506UK) / bis zu 12 Systemen (LDU505 und LDU506)

Die Verwendung von drahtlosen Mikrofonsystemen kann eine Genehmigung erfordern - je nach landesspezischen Bestimmungen. Bitte kontaktier-

en Sie Ihre zuständigen Behörde für weitere Informationen.

LIEFERUMFANG

LDU5xxHHC: Einzelempfänger plus Handsender und Kondensatorkapsel (cardioid), Netzteil, 2x BNC-Antennen, Audiokabel, 2x AA Batterien, Transport-

koffer, Anleitung

LDU5xxHHD: Einzelempfänger plus Handsender und dynamischer Kapsel (cardioid), Netzteil, 2x BNC-Antennen, Audiokabel, 2x AA Batterien, Trans-

portkoffer, Anleitung

LDU5xxBPH: Einzelempfänger plus Taschensender und Headset (schwarz), Netzteil, 2x BNC-Antennen, Audiokabel, 2x AA Batterien,

Transportkoffer, Anleitung

LDU5xxBPHH: Einzelempfänger plus Taschensender und Headset (hautfarben), Netzteil, 2x BNC-Antennen, Audiokabel, 2x AA Batterien,

Transportkoffer, Anleitung

LDU5xxBPG: Einzelempfänger plus Taschensender und Gitarrenkabel, Netzteil, 2x BNC-Antennen, Audiokabel, 2x AA Batterien,

Transportkoffer, Anleitung

LDU5xxBPL: Einzelempfänger plus Taschensender und Lavalier-Mikrofon, Netzteil, 2x BNC-Antennen, Audiokabel, 2x AA Batterien,

Transportkoffer, Anleitung

LDU5xxBPW: Einzelempfänger plus Taschensender und Clip-Mikrofon für Blasinstrumente, Netzteil, 2x BNC-Antennen, Audiokabel, 2x AA Batterien,

Transportkoffer, Anleitung

LDU5xxHHC2: Doppelempfänger plus 2x Handsender und Kondensatorkapsel (cardioid), Netzteil, 2x BNC-Antennen, Audiokabel, 4x AA Batterien,

Transportkoffer, Rack-Kit, Anleitung

LDU5xxHHD2: Doppelempfänger plus 2x Handsender und dynamischer Kapsel (cardioid), Netzteil, 2x BNC-Antennen, Audiokabel, 4x AA Batterien,

Transportkoffer, Rack-Kit, Anleitung

19

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

ANSCHLÜSSE, BEDIEN- UND ANZEIGEELEMENTE

LDU5xxBPH2: Doppelempfänger plus 2x Taschensender und Headset (schwarz), Netzteil, 2x BNC-Antennen, Audiokabel, 4x AA Batterien,

Transportkoffer, Rack-Kit, Anleitung

LDU5xxBPHH2: Doppelempfänger plus 2x Taschensender und Headset (hautfarben), Netzteil, 2x BNC-Antennen, Audiokabel, 4x AA Batterien,

Transportkoffer, Rack-Kit, Anleitung

Eine umfangreiche Auswahl an LD U500 Einzelkomponenten und Zubehör nden Sie auf www.LD-SYSTEMS.COM

1

2

5

3

4

9

8

1

2

3

4

5

6

7

2

3

4

9

8

EMPFÄNGER

1

POWER

Ein- bzw. Ausschalter. Drücken und halten Sie den Taster für die Dauer von ca. 2 Sekunden, um das Gerät ein- bzw. auszuschalten.

2

DISPLAY

Ein- bzw. Ausschalter. Drücken und halten Sie den Taster für die Dauer von ca. 2 Sekunden, um das Gerät ein- bzw. auszuschalten.

3

MENU

Kombinierter Drück-Dreh-Geber, um in das Bearbeitungsmenü zu gelangen und die einzelnen Menüpunkte auszuwählen und zu editieren.

4

VOL

Dreh-Geber zum Einstellen der Lautstärke des an den Audio-Ausgängen anliegenden Audio-Signals. Sobald Lautstärkeänderungen vorgenommen

werden, wird die Lautstärkeeinstellung augenblicklich im Display angezeigt (VOLUME 00 - 100). Nach ca. 3 Sekunden Inaktivität kehrt das Display zur

Hauptanzeige zurück.

5

Infrarot-Schnittstelle zum Synchronisieren der relevanten Systemeinstellungen des Empfängers mit dem Sender (z.B. Sendefrequenz).

6

KOPFHÖRERAUSGANG

6,3mm Klinkenbuchse zum Anschließen eines Kopfhörers (nur Doppelempfänger).

7

KOPFHÖRERLAUTSTÄRKE

Drehregler zum Einstellen der Kopfhörerlautstärke (nur Doppelempfänger).

8

Vorrichtung zum Anbringen der Antennen beim Rackeinbau. Entfernen Sie die Abdeckkappen, befestigen die BNC-Adapter an der Frontblende und

verbinden die BNC-Antennenanschlüsse (Abb. 11, Doppelempfänger) mit den BNC-Adaptern in der Frontblende (kurze Antennenkabel und BNC-Adap-

ter im Lieferumfang). Nun können die Antennen an der Vorderseite des Empfängers befestigt werden.

9

Schraublöcher für den 19“ Rackeinbau.

20

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

La page charge ...

LD Systems U508 BPG Manuel utilisateur

LD Systems U508 BPG Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents