Hitachi C 10FSH Safety Instructions And Instruction Manual

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

Model

Modèle

Modelo

C 10FSH

C 10FSB

(Laser Marker Equipment)

(Equipement à marqueur laser)

(Equipo con marcador láser)

Slide Compound Miter Saw

Scie à onglets coulissante

Ingletadora telescopica

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE

use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand this

manual BEFORE operating the power tool. Please keep this manual available for other users and

owners before they use the power tool. This manual should be stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation

INCORRECTE OU DANGEREUSE

de cet outil motorisé peut entraîner la mort ou de

sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière

de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce mode d’emploi

à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode

d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización

INAPROPIADA O PELIGROSA

de esta herramienta eléctrica puede resultar en lesiones

de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este

manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras

personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.

CONTENTS

PAGE

IMPORTANT SAFETY INFORMATION ....................3

MEANINGS OF SIGNAL WORDS ............................3

SAFETY .......................................................................3

IMPORTANT SAFETY INSTRUCTIONS FOR

USING ALL POWER TOOLS .............................3

REPLACEMENT PARTS ..........................................6

USE PROPER EXTENSION CORD .........................7

DOUBLE INSULATION FOR SAFER OPERATION ...7

OPERATION AND MAINTENANCE ............................8

NAME OF PARTS .....................................................8

SPECIFICATIONS ....................................................9

PAGE

ACCESSORIES ......................................................10

APPLICATIONS ......................................................10

PREPARATION BEFORE OPERATION .................11

BEFORE USING ....................................................12

BEFORE CUTTING ................................................13

PRACTICAL APPLICATIONS .................................18

SAW BLADE MOUNTING AND

DISMOUNTING ...............................................26

MAINTENANCE AND INSPECTION ......................27

SERVICE AND REPAIRS .......................................28

PARTS LIST ...............................................................86

English

TABLE DES MATIERES

PAGE

INFORMATIONS IMPORTANTES

DE SÉCURITÉ .................................................29

SIGNIFICATION DES MOTS

D’AVERTISSEMENT ........................................29

SECURITE .................................................................29

CONSIGNES DE SECURITE RELATIVES AUX

OUTILS ÉLECTRIQUES ..................................29

PIECES DE RECHANGE .......................................33

UTILISER LE CORDON DE

RALLONGE APPROPRIÉ ................................33

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR .....................33

UTILISATION ET ENTRETIEN ..................................35

NOM DES PIÈCES .................................................35

PAGE

SPÉCIFICATIONS ..................................................36

ACCESSOIRES ......................................................37

APPLICATIONS ......................................................37

PRÉPARATION AVANT L’UTILISATION .................38

AVANT L’UTILISATION ...........................................39

AVANT LA COUPE .................................................40

APPLICATIONS PRATIQUES .................................45

INSTALLATION ET RETRAIT DE LA LAME ...........53

ENTRETIEN ET INSPECTION ...............................54

SERVICE APRÈS-VENTE ET RÉPARATIONS .......56

LISTE DES PIECES ..................................................86

Français

ÍNDICE

PÁGINA

INFORMACIÓN IMPORTANTE SOBRE

SEGURIDAD .................................................... 57

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ...............................................57

SEGURIDAD ..............................................................57

NORMAS DE SEGURIDAD PARA LAS

HERRAMIENTAS ELÉCTRICAS ......................57

PIEZAS DE REEMPLAZO ......................................61

UTILICE EL CABLE PROLONGADOR

ADECUADO ..................................................... 61

AISLAMIENTO DOBLE PARA OFRECER UNA

OPERACIÓN MÁS SEGURA ...........................62

OPERACIÓN Y MANTENIMIENTO ...........................63

NOMENCLATURA DE PARTES .............................63

ESPECIFICACIONES ............................................. 64

PÁGINA

ACCESORIOS........................................................65

APLICACIONES .....................................................65

PREPARATIVOS PREVIOS A LA OPERACIÓN .....66

ANTES DE LA UTILIZACIÓN .................................67

ANTES DEL CORTE ..............................................68

APLICACIONES PRÁCTICAS ................................73

MONTAJE Y DESMONTAJE DE LA

HOJA DE SIERRA ...........................................82

MANTENIMIENTO E INSPECCIÓN .......................83

SERVICIO Y REPARACIONES ...............................85

LISTA DE PIEZAS .....................................................86

Español

3

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual

before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation

before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by WARNINGS on the

power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been speciﬁ cally recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate

injury, or may cause machine damage.

NOTE emphasizes essential information.

SAFETY

IMPORTANT SAFETY INSTRUCTIONS FOR USING ALL POWER TOOLS

READ ALL OF THE WARNINGS AND OPERATING INSTRUCTIONS IN THIS MANUAL

BEFORE OPERATING OR MAINTAINING THIS TOOL:

WARNING: When using this electric tool, take all necessary precautions to minimize the risk of

electric shock or other personal injury.

In particular, always comply with the following safety rules:

1. ALWAYS KEEP GUARDS IN PLACE and in working order.

2. ALWAYS REMOVE ADJUSTING KEYS AND WRENCHES BEFORE STARTING TOOL.

Always conﬁ rm that all keys and adjusting wrenches have been removed from the tool before it is turned on.

3. ALWAYS KEEP WORK AREA CLEAN. Avoid injuries by not cluttering the work areas and work

benches.

4. NEVER USE TOOL IN HAZARDOUS ENVIRONMENTS. Never use the power tool in damp or wet

places and never expose it to rain. Always keep the work area well lighted.

5. NEVER PERMIT CHILDREN OR OTHERS TO LOITER NEAR THE WORK AREA. Keep

all people (especially children) away from the work area. Always unplug unattended tools and keep the work

place tamper-proof by installing locks on the doors and on the master switches. Always remove the lock-oﬀ

button from the tool and store it in a secure place, when the tool is not in use.

6. NEVER FORCE THE TOOL. It will do the job better and more safely if it is operated at the rate for which

it was designed.

7. ALWAYS USE THE RIGHT TOOLS. Never force a tool or an attachment to do a job for which it was not

designed.

8. ALWAYS WEAR PROPER APPAREL WHEN WORKING WITH THE TOOL. Never wear loose

clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught in the moving parts. Always

wear non-slip footwear, preferably with steel toes. Wear protective hair covering to contain long hair.

4

English

9. ALWAYS WEAR EYE PROTECTION WITH SIDE SHIELDS THAT MEETS THE

REQUIREMENTS OF ANSI STANDARD Z87.1 WHEN WORKING WITH THE TOOL TO

PREVENT EYE INJURY.

Ordinary eyeglasses do not provide adequate protection because they do not

contain impact resistant safety glass. Also, use a face mask for additional safety and wear a dust mask if the

cutting operation produces dust.

10. ALWAYS SECURE THE WORKPIECE TO THE FENCE OR THE TABLE. Use clamps or a vise

to hold the workpiece in place. It is safer than using your hand and it frees both hands to operate the tool.

11. NEVER OVERREACH. Always keep proper footing and balance when working with the tool.

12. ALWAYS MAINTAIN TOOLS WITH CARE. Always keep tools sharp and clean for the best and safest

performance. Always follow instructions for lubricating the tool and for changing accessories.

13. ALWAYS DISCONNECT THE TOOL before servicing and before changing blades or other accessories.

14. NEVER RISK UNINTENTIONAL STARTING WHEN PLUGGING IN THE TOOL. Always

conﬁ rm that the switch is in the OFF position before inserting the power plug into the receptacle.

15. ALWAYS USE RECOMMENDED ACCESSORIES ONLY WHEN OPERATING THIS TOOL.

Consult this instruction manual for descriptions of recommended accessories. To avoid personal injuries, use

only recommended accessories in conjunction with this tool.

16. NEVER STAND ON THE TOOL. Prevent serious injury by not tipping the tool and by not risking

unintentional contact with the saw blade.

17. ALWAYS CHECK FOR DAMAGED PARTS BEFORE USING THE TOOL. Always check the

guard and all other components for damage before using the tool to assure that they will function properly.

Check all moving parts for proper alignment, freedom from binding and other conditions that might aﬀ ect

proper operation. Always repair or replace any damaged guards or other damaged components before using

the tool.

18. ALWAYS CONFIRM THE ROTATION DIRECTION OF THE BLADE BEFORE USING THE

TOOL.

Always feed work into the tool against the rotation direction of the blade in order to prevent possible

injury.

19. NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED. TURN POWER OFF. Do not

leave tool until it comes to a complete stop. Always turn the power oﬀ when the tool is not in use. Always unplug

the power cord when the tool is not in use.

20. This tool was not designed to be used for mass-production applications and should not be used in mass-

production environments.

21. When servicing this tool, use only authorized replacement parts.

22. Apply 120 volts AC only to this tool. Applying the wrong voltage or applying DC power can cause the POWER

TOOL to operate improperly and cause serious personal injury or damage to the tool.

23. Never raise the saw blade from the workpiece until it has ﬁ rst come to a complete stop.

24. Always use outboard stands to provide support for long workpieces that overhang the table of the slide

compound miter saw.

25. Always return the carriage to the full rear position after each crosscut operation in order to reduce the risk of

injury.

26. POLARIZED PLUGS To reduce the risk of electric shock, this equipment has a polarized plug (one blade

is wider than the other). This plug will ﬁ t in a polarized outlet only one way. If the plug does not ﬁ t fully in the

outlet, reverse the plug. If it still does not ﬁ t, contact a qualiﬁ ed electrician to install the proper outlet. Do not

change the plug in any way.

Speciﬁ c Safety Rules for Use of this Power Tool

WARNING: The following speciﬁ c operating instructions must be observed when using this POWER

TOOL in order to avoid injury:

DO’s

ALWAYS OBSERVE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL:

1.

Review this Manual and familiarize yourself with the safety rules and operating instructions for this POWER

TOOL before attempting to use it.

5

English

2. Remove all packing materials attached or connected to the tool before attempting to operate it.

3. Always conﬁ rm that the POWER TOOL is clean before using it.

4. Always wear snug-ﬁ tting clothing, non-skid footwear (preferably with steel toes) and eye protection when

operating the POWER TOOL.

5. Always handle the POWER TOOL carefully. If the POWER TOOL falls or strikes against a hard object, it might

become deformed or cracked or sustain other damage.

6. Always cease operating the saw at once, if you notice any abnormality whatsoever.

7. Always conﬁ rm that all components are mounted properly and securely before using the tool.

8. When replacing the saw blade, always conﬁ rm that the rpm rating of the new blade is correct for use on this tool.

9. Always shut oﬀ the power and wait for the saw blade to completely stop rotating before doing any maintenance

or adjustments.

10. During slide cutting, always push the saw blade away from the operator.

11. Always clamp or otherwise secure the workpiece to the fence; otherwise the workpiece might be thrust form

the table and cause bodily harm.

12. During miter or bevel cutting, always wait for the rotation of the blade to stop completely before lifting the saw

blade.

13. Always make a trial run ﬁ rst before attempting any new use of the saw.

14. Always handle the saw blade with care when dismounting and mounting it.

15. Always conﬁ rm that the workpiece is free of nails or other foreign objects before beginning a cut.

16. Always keep your hands out of the path of the saw blade.

17. Always conﬁ rm that the lower guard is in the proper place before using the saw.

18. Always conﬁ rm that the lower guard does not obstruct the sliding motion of the saw before attempting slide

cutting.

19. Inspect the tool power cords periodically.

20. Always conﬁ rm that the proper lengths and types of extension cords are being utilized, if necessary, before

starting the tool.

21. Always conﬁ rm that the motor air vents are fully open before using the tool.

22. Always wait until the motor has reached full speed before starting a cut.

23. Always keep the handles dry, clean and free of oil and grease. Hold the tool ﬁ rmly when in use.

24. Always use outboard stands to provide support for long workpieces that overhang the table of the slide

compound miter saw.

25. Always operate the tool after ensuring the workpiece is ﬁ xed properly with a vise assembly.

26. The operating instructions provided with the tool shall direct the user to secure the tool to supporting structure

if, during normal operation, there is a tendency for the tool to tip over, slide, or walk on the supporting surface.

DON’Ts

NEVER VIOLATE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL:

1.

Never operate the POWER TOOL unless you fully understand the operating instructions contained in this

Manual.

2. Never leave the POWER TOOL unattended without ﬁ rst unplugging the power cord.

3. Never operate the POWER TOOL when you are tired, after you have taken any medications, or have consumed

any alcoholic beverages.

4. Never use the POWER TOOL for applications not speciﬁ ed in the instruction manual.

5. Never operate the tool while wearing loose clothing, a necktie or jewelry, or while your hair is uncovered, to

protect against getting caught in the moving machinery.

6. Never reach around the saw blade.

6

English

7. Never touch any moving parts, including the blade, while the saw is in use.

8. Never remove any safety devices or blade guards; use of the tool without them would be hazardous.

9. Never lock the lower guard; always conﬁ rm that it slides smoothly before using the tool.

10. Never damage the power cord of the tool.

11. Never attempt to move a plugged-in POWER TOOL while your ﬁ nger is on the starting switch.

12. Never use the POWER TOOL if the starting switch does not turn on and oﬀ properly.

13. Never use the POWER TOOL if the plastic housing or the handle is cracked or deformed.

14. Never use the POWER TOOL near ﬂ ammable liquids or gases because sparking can cause an explosion.

15. Never clean plastic components with solvents because the plastic may dissolve.

16. Never operate the saw unless all the blade guards are in place.

17. Never raise the saw blade from the workpiece until it has ﬁ rst come to a complete stop.

18. When slide cutting, never pull the handle toward the operator, since this could cause the saw blade to kick up

from the workpiece. Always push the handle away from the operator in a single, smooth motion.

19. Never place your limbs inside of the line next to warning sign “ ” while the tool is being operated. This may

cause hazardous conditions.

20. Never use abrasive type blades on this saw.

21. Never expose to rain or use in damp locations.

22. Never cut ferrous metals or masonry.

WARNING

FOR YOUR OWN SAFETY READ THIS INSTRUCTION MANUAL BEFORE OPERATING THE

SLIDE COMPOUND MITER SAW

1.

Always wear eye protection when using the slide compound miter saw.

2. Always keep hands out of the path of the saw blade.

3. Never operate the saw without the guards in place.

4. Never perform any freehand operation with the slide compound miter saw.

5. Never reach around the saw blade.

6. Always turn oﬀ tool and wait for saw blade to stop before moving workpiece or changing settings.

7. Always disconnect power before changing blade or servicing.

8. Saw blade diameter is 10" (255mm).

9. No load speed is 3800/min.

10. To reduce the risk of injury, return carriage to the full rear position after each crosscut operation.

REPLACEMENT PARTS

When servicing use only identical replacement parts.

Repairs should be conducted only by a Hitachi authorized service center.

7

English

USE PROPER EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy

enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting

in loss of power and overheating. Table shows the correct size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

MINIMUM GAGE FOR CORD SETS

Total Length of Cord in Feet (Meter)

0 – 25

(0 – 7.6)

26 – 50

(7.9 – 15.2)

51 – 100

(15.5 – 30.5)

101 – 150

(30.8 – 45.7)

Ampere Rating AWG

More

Than

Not More

Than

0 – 6

6 – 10

10 – 12

12 – 16

18

16

14

16

12

16

14

12

Not Recommended

WARNING: Avoid electrical shock hazard. Never use this tool with a damaged or frayed electrical

cord or extension cord.

Inspect all electrical cords regularly. Never use in or near water or in any environment

where electric shock is possible.

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation”

means that two physically separated insulation systems have been used to insulate the electrically conductive

materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol

“ ” or the words and “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical safety precautions given

in this Instruction Manual, including not using the power tool in wet environments.

To keep the double insulation system eﬀ ective, follow these precautions:

* Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool, and only

genuine HITACHI replacement parts should be installed.

* Clean the exterior of the power tool only with a soft cloth moistened with soapy water and dry thoroughly.

* Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

8

English

OPERATION AND MAINTENANCE

NOTE: The information contained in this Instruction Manual is designed to assist you in the safe

operation and maintenance of the power tool. Some illustrations in this Instruction Manual may

show details or attachments that diﬀ er from those on your own power tool.

NAME OF PARTS

MODEL C10FSH/MODEL C10FSB

Dust Bag

Handle

Spindle Cover

Lower guard

Fence (A)

Table Insert

Turntable

Side Handle

Hinge

Holder (A)

Saw Blade

Fence (B)

Motor Head

Indicator

(For miter scale)

Rotation

Direction

Motor

Lever

Sub Fence

Vise Assembly

Laser Marker

(Only C10FSH)

Indicator

(For right bevel scale)

Gear Case

Fig. 1

Trigger Switch

Locking Pin

Slide Securing Knob

Fixing Pin

Nameplate

5mm Screw

Spindle Lock

Base

Guard

Clamp Lever

Belt Cover

Holder

Indicator

(for left bevel scale)

Adjuster (Only C10FSH)

(for Laser marker)

Switch

(for Laser marker)

(Only C10FSH)

Fig. 2

9

English

SPECIFICATIONS

Item Model C 10FSH / C 10FSB

Motor Type Series commutator motor

Power source Single-phase AC 60Hz

Voltage (Volts) 120

Full-load current (Amp) 12

Laser Marker

(Only Model

C10FSH)

Maximum output <1mW CLASS II Laser Product

Wave length 400~700 nm

Laser medium Laser Diode

Applicable

saw blade

Outside Dia. 10" (255mm)

Hole Dia. 5/8" (15.9mm)

No load speed 3800/min

Max.

sawing

dimension

Head Turntable Max. sawing dimension

Miter 0 0 Max. Height

Max. Width

or

* Max. Height

Max. Width

With aux. board

3-11/32"

12-9/32"

3-9/16"

11"

19/32"

(85mm)

(312mm)

(90mm)

(280mm)

(15mm)

0 Left 45°

or

Right 45°

Max. Height

Max. Width

or

* Max. Height

Max. Width

With aux. board

3-11/32"

8-19/32"

3-9/16"

7-1/2"

19/32"

(85mm)

(218mm)

(90mm)

(190mm)

(15mm)

0 Right 57° Max. Height

Max. Width

or

* Max. Height

Max. Width

With aux. board

3-11/32"

6-1/2"

3-9/16"

5-25/32"

13/32"

(85mm)

(165mm)

(90mm)

(147mm)

(10mm)

Bevel Left 45° 0 Max. Height

Max. Width

or

* Max. Height

Max. Width

With aux. board

2-3/16"

12"

2-3/8"

11"

19/32"

(55mm)

(305mm)

(60mm)

(280mm)

(15mm)

Right 45° 0 Max. Height

Max. Width

or

* Max. Height

Max. Width

With aux. board

1-3/16"

12"

1-3/8"

11"

19/32"

(30mm)

(305mm)

(35mm)

(280mm)

(15mm)

Compound Left 45° Left 45°

or

Right 45°

Max. Height

Max. Width

or

* Max. Height

Max. Width

With aux. board

2-3/16"

8-19/32"

2-3/8"

7-1/2"

19/32"

(55mm)

(218mm)

(60mm)

(190mm)

(15mm)

Right 45° Left 31° Max. Height

Max. Width

or

* Max. Height

Max. Width

With aux. board

1-3/16"

10-7/32"

1-3/8"

9-19/32"

19/32"

(30mm)

(260mm)

(35mm)

(230mm)

(15mm)

Right 45° Right 45° Max. Height

Max. Width

or

* Max. Height

Max. Width

With aux. board

1-3/16"

8-19/32"

1-3/8"

7-1/2"

19/32"

(30mm)

(218mm)

(35mm)

(190mm)

(15mm)

Miter sawing range Left 0° – 45° Right 0° – 57°

Bevel sawing range Left 0° – 45° Right 0° – 45°

Compound sawing range Left (Bevel) 0° – 45°, Left and Right (Miter) 0° – 45°

Right (Bevel) 0° – 45°, Left (Miter) 0° – 31°, Right (Miter) 0° – 45°

Net weight 43lbs. (19.5kg)

Cord 2 Conductor type cable 6ft. (1.8m)

10

English

When cutting the workpiece which has the dimension of “*” there might be some possibility of the lower end of

the circular saw to touch with the workpiece, even if the motor head is located at the lower limit position. Pay

attention when cutting the workpiece. For further details, refer to “PRACTICAL APPLICATIONS” on page 18. Mount

the auxiliary board on the fence surface (Refer ( ) the thickness of auxiliary board). Refer to “5. Cutting large

workpieces” on page 20 (Fig. 27).

ACCESSORIES

WARNING: Accessories for this power tool are mentioned in this Instruction Manual.

The use of any other attachment or accessory can be dangerous and could cause injury

or mechanical damage.

STANDARD ACCESSORIES

2 Dust bag (1 piece)1 10" (255mm) TCT Saw blade

(1 piece)

For how to use, refer to

page 25.

4 10mm BOX wrench

(1 piece)

3 Vise Assembly w/knob bolt

(1 piece)

For how to use, refer to

page 18.

No. of teeth 40

Code No. 310878 (C329701)

Fig. 3

OPTIONAL ACCESSORIES...sold separately

1 Extension Holder and Stopper (Code No. 321553)

2 Saw blade 10"(255mm) TCT Saw blade (Total teeth:72) (Code No. 725206)

3 Sub Fence (A) (Code No. 321387)

4 Crown molding Vise Ass’y (Code No. 321434) (Include Crown molding Stopper (L))

5 Crown molding Stopper (L) (Code No. 321374)

6 Crown molding Stopper (R) (Code No. 321373)

NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.

APPLICATIONS

Wood and aluminum sash.

11

English

PREPARATION BEFORE OPERATION

Make the following preparations before operating the power tool:

1. Remove all packing materials attached or connected to the tool before attempting to operate it.

2. Installation

1" (25mm) thick bench

Work Bench

5/16" (8mm) Nut

5/16" (8mm) BoltBase

5-29/32"(150mm)

11-13/16" (300mm)

11/32" (9mm)

3 Holes

10-13/32" (264mm)

Fig. 4

Attach the power tool to a level, horizontal work bench in accordance with Fig. 4.

Select 5/16" (8mm) diameter bolts suitable in length for the thickness of the work bench.

Bolt length should be at least 1-9/16" (40mm) plus the thickness of the work bench.

For example, use 2-9/16" (65mm) or larger bolts for a 1" (25mm) thick work bench.

The holder attached to the rear of the base helps stabilize the power tool.

Holder adjustment:

Loosen the 6mm bolt with the supplied 10mm box wrench.

Adjust the holder until its bottom surface contacts the work bench

surface.

After adjustment, ﬁ rmly tighten the 6mm bolt.

Fig. 5

3. Releasing the locking pin

When the power tool is prepared for shipping, its main parts are secured

by a locking pin.

Move the handle slightly so that the locking pin can be disengaged.

NOTE: Lowering the handle slightly will enable you to disengage

the locking pin more easily and safely.

The lock position of the locking pin is for carrying and

storage only.

Fig. 6

4. Installing the dust bag, holder, stopper and vises

(The holder and stopper are optional accessories.)

Attach the dust bag and vise assembly as indicated in Fig. 1 and Fig. 2.

6mm Bolt

Move

Adjust the holder

until its bottom

surface contacts the

work bench surface.

Holder

Locking Pin

Pull

Handle

12

English

BEFORE USING

1. Make sure the power source is appropriate for the tool.

WARNING: Never connect the power tool unless the available AC power source is of the same

voltage as that speciﬁ ed on the nameplate of the tool.

Never connect this power tool to a DC power source.

2. Make sure the trigger switch is turned OFF.

WARNING: If the power cord is connected to the power source with the trigger switch turned

ON the power tool will start suddenly and can cause a serious accident.

3. Check the saw blade for visible defects.

Conﬁ rm that the saw blade is free of cracks or other visible damage.

4. Conﬁ rm that the saw blade is attached securely to the power tool.

Using the supplied 10mm box wrench, tighten the bolt on the saw blade spindle to secure the saw blade.

For details, see Fig. 51-a, Fig. 51-b and Fig. 51-c in the section on “SAW BLADE MOUNTING AND

DISMOUNTING”.

5. Check the lower guard for proper operation.

Lower guard is designed to protect the operator from coming into contact

with the saw blade during operation of the tool.

Always check that the lower guard moves smoothly and covers the saw

blade properly.

Fig. 7

WARNING: NEVER OPERATE THE POWER TOOL if the lower guard does not function smoothly.

6. Conﬁ rm the position of the spindle lock before using the tool.

After installing the saw blade, conﬁ rm that the spindle lock has been returned to the retract position before

using the power tool (see Fig. 2).

7. Check the lower limit position of the Saw Blade.

Although it was adjusted before shipment, carefully check the height of the saw blade. Conﬁ rm that the saw

blade can be lowered 13/32" to 7/16" (10mm to 11mm) below the table insert. For details, see the section on

“Checking the saw blade lower limit position”.

8. Check the Power Receptacle.

To prevent overheating, accidental stopping or intermittent operation, conﬁ rm that the power cord plug ﬁ ts

properly in the electrical receptacle and does not fall out after it is inserted. Repair or replace the receptacle if

it is faulty.

9. Conﬁ rm the tool’s power cord is not damaged.

Repair or replace the power cord if an inspection indicates that it is damaged

10. Eye protection

Always wear eye protection with side shields that meets the requirements of ANSI Standard Z87.1. Ordinary

eyeglasses do not provide adequate protection because they do not contain impact resistant safety glass.

WARNING: Operating the tool without wearing proper eye protection may result in serious

injury.

11. Electric brake

This tool is equipped with an electric brake which will typically stop the blade within 5 seconds after the trigger

switch is released.

Occasionally, there will be a delay in the brake engaging which will result in a longer blade stopping time. On

rare occasions, the brake may not engage at all and the saw blade will coast to a stop.

Lower guard

13

English

If the brake fails to engage frequently, depress and release the trigger switch to turn the tool on and oﬀ 4 or 5

times. If the brake still does not engage, have the tool serviced at a Hitachi authorized service center.

Always conﬁ rm that the saw blade has completely stopped before raising it from the workpiece.

The brake is not a substitute for a properly functioning lower guard. Check the function of the lower guard

before each use. Serious personal injury may occur if the lower guard does not move smoothly and cover the

blade properly.

WARNING: Please be aware of the reaction of the Motor Head (Fig.1) when the brake is activated.

Braking causes the Motor Head to jerk downward and the user should be prepared

for this reaction, especially when the trigger switch is released before the blade

is completely down. Failure to be familiar with, and prepared for, the operational

characteristics of the tool may cause serious injury.

AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE,

CHECK THE OPERATION OF THE TOOL AS FOLLOWS:

12. Trial Run

After conﬁ rming that no one is standing behind, the power tool start and conﬁ rm that no operating abnormalities

exist before attempting a cutting operation.

13. Inspect the rotating stability of the saw blade.

For precise cutting, rotate the saw blade and check for deﬂ ection to conﬁ rm that the blade is not noticeably

unstable; otherwise vibrations might occur and cause an accident.

BEFORE CUTTING

1. Positioning the table insert

Table insert

Workpiece

Table insert

Saw Blade

Workpiece

Table insert

Saw Blade

6mm

Machine

Screw

6mm

Machine

Screw

6mm

Machine

Screw

[Right angle cutting]

Fig. 8-a

[Left bevel angle cutting]

Fig. 8-b

[Right bevel angle cutting]

Fig. 8-c

Table inserts are installed on the turntable. When shipping the tool from the factory, the table inserts are so

ﬁ xed that the saw blade does not contact them. The burr of the bottom surface of the workpiece is remarkably

reduced, if the table insert is ﬁ xed so that the gap between the side surface of the table insert and the saw

blade will be minimum. Before using the tool, eliminate this gap in accordance with the following procedure.

(1) Right angle cutting

Loosen the three 6mm machine screws, then secure the left side table insert and temporarily tighten

the 6mm machine screws of both ends. Then ﬁ x a workpiece (about 7-7/8" (200mm) wide) with the vise

assembly and cut it oﬀ . After aligning the cutting surface with the edge of the table insert, securely tighten

the 6mm machine screws of both ends. Remove the workpiece and securely tighten the 6mm center

machine screw. Adjust the right hand table insert in the same way.

(2) Left and right bevel angle cutting

Adjust the table insert in the manner shown in Fig. 8-b and Fig. 8-c following the same procedure for right

angle cutting.

CAUTION: After adjusting the table insert for right angle cutting, the table insert will be cut to

some extent if it is used for bevel angle cutting.

When bevel cutting operation is required, adjust the table insert for bevel angle

cutting.

2. Checking the saw blade lower limit position

Check that the saw blade can be lowered 13/32" to 7/16" (10mm to 11mm) below the table insert as shown in

Fig. 9.

When you replace a saw blade with a new one, adjust the lower limit position so that the saw blade will not cut

the turntable or complete cutting cannot be done.

To adjust the lower limit position of the saw blade, follow the procedures (1) to (4) indicated below. (Fig. 10)

14

English

Furthermore, when changing the position of a 8mm depth adjustment bolt that serves as a lower limit position

stopper of the saw blade, it becomes necessary to shift the position of a 8mm hexagon socket set screw that

is in the screw hole for the 8mm depth adjustment bolt that serves as the stopper.

(1) Loosen the 8mm wing nut.

(2) Insert your 6mm hexagon bar wrench from behind of the tool and turn

the 8mm hexagon socket set screw to the left (counterclockwise) as

viewed from behind of the tool.

(3) Turn the 8mm depth adjustment bolt, change the height where the

bolt head and the gear case contacts, and adjust the lower limit

position of the saw blade. One turn of the 8mm depth adjustment

bolt changes the lower limit position of the saw blade by about

5/16"(8mm), and this information can be used as a rough guide.

(4) Turn the 8mm hexagon socket set screw to the right (clockwise) as

viewed from behind of the tool, and let it softly contact the tip of the

8mm depth adjustment bolt.

3. Lower limit position of saw blade when cutting a large workpiece

NOTE:

When cutting a workpiece exceeding 3-11/32" (85mm) in height in right-angle cutting or

2-3/16"(55mm) in left bevel angle cutting or 1-3/16" (30mm) in right bevel angle cutting,

adjust the lower limit position so that the base of the motor head (see Fig. 9) will not come

in contact with the workpiece.

To adjust the lower limit position of the saw blade, follow the procedures (1) to (3) shown in Fig. 10-a.

(1) Loosen the 8mm wing nut so that the 8mm depth adjustment bolt can be turned by hand.

(2) Lower the motor head, and thru the 8mm depth adjustment bolt by hand and make adjustments so that

there can be a clearance of 3/32" to 1/8" (2mm to 3mm) between the lower limit position of the motor head

and the top of the workpiece at the saw blade’s lower limit position (where the head of the 8mm depth

adjustment bolt contacts the gear case.

(3) After adjustment, turn the 8mm wing nut until it contacts the Hinge (see Fig. 10), and fully tighten it.

4. Conﬁ rmation for use of sub fence

WARNING: In the case of left bevel cutting, turn the sub fence counterclockwise. Unless it is

turned counterclockwise, the main body or saw blade may contact the sub fence,

resulting in an injury.

This power tool is Equipped with a sub fence.

In the case of direct angle cutting and right bevel angle cutting, use the

sub fence. Then, you can realize stable cutting of the material with a

wide back face.

In the case of left bevel cutting, raise the sub fence up as illustrated in

Fig. 11 and then turn it counterclockwise.

Gear Case

Base

8mm Wing Nut

8mm Depth

Adjustment

Bolt

Saw Blade

Turntable

Fig. 9

8mm Depth

Adjustment Bolt

8mm Hexagon Socket

Set Screw

Turn

8mm Wing Nut

Loosen

Gear Case

Hinge

Fig. 10

Sub Fence

Left bevel angle cutting

Turn

Right bevel angle cutting

Direct angle cutting

Fence (B)

Fig. 11

15

English

5. Oblique angle

Before the power tool is shipped from the factory, it is adjusted for 0°, right angle, left 45° bevel cutting angle

and right 45° bevel cutting angle with the 8mm bolt (A), 8mm bolt (B) and the 8mm bolt (C).

When changing the adjustment, change the height of the 8mm bolt (A), 8mm bolt (B) or the 8mm bolt (C) by

turning them.

When changing the bevel angle to the right 45°, pull the ﬁ xing pin on the direction shown in Fig. 12-a and incline

the motor head to the right.

When adjusting the motor head to 0°, always return the ﬁ xing pin to its initial position as shown in Fig. 12-b.

8mm Bolt (C)

(Stopper for left 45°

bevel angle)

Indicator

(For left bevel

scale)

Fixing Pin

Pull

Fig. 12-a

8mm Bolt (B) (Stopper for right

45° bevel angle)

8mm Bolt (A) (Stopper for 0°)

Return

Fixing Pin

Indicator (For right bevel scale)

Fig. 12-b

6. Securing the workpiece

WARNING: Always clamp or vise to secure the workpiece to the fence; otherwise the workpiece

might be thrust from the table and cause bodily harm.

7. Installing the holders ... (Optional accessory)

The holders help keep longer workpieces stable and in place during the

cutting operation.

(1) As indicated in Fig. 13, use a steel square for aligning the upper

edge of the holders with the base surface.

Loosen the 6mm wing nut. Turn a height adjustment bolt 6mm, and

adjust the height of the holder.

(2) After adjustment, ﬁ rmly tighten the wing nut and fasten the holder

with the 6mm knob bolt (optional accessory). If the length of Height

Adjustment Bolt 6mm is insuﬃ cient, spread a thin plate beneath.

Make sure the end of Height Adjustment Bolt 6mm does not protrude

from the holder.

8. Stopper for precision cutting ... (Stopper and holder are optional accessory)

Workpiece

Stopper

(Optional accessory)

6mm Knob Bolt

(Optional accessory)

Holder

(Optional

accessory)

Move

6mm Wing Nut (Optional accessory)

Height Adjustment Bolt 6mm (Optional accessory)

Fig. 14

The stopper facilitates continuous precision cutting in lengths of 11" to

17-3/4" (280mm to 450mm).

To install the stopper, attach it to the holder with the 6mm knob bolt as

shown in Fig. 14.

6mm Knob Bolt

(Optional accessory)

Holder

(Optional

accessory)

Steel

Square

Base Surface

6mm Wing Nut

(Optional

accessory)

Height Adjustment Bolt 6mm

(Optional accessory)

Fig. 13

16

English

9. Conﬁ rmation for use of sub fence (A)…(Optional accessory)

WARNING: In the case of right bevel cutting, remove the sub

fence (A). Supposing it is not able to remove it,

It will contact the blade or some part of the tool,

causing in serious injury to operator.

In the case of direct angle cutting and angle cutting, use the sub fence (A).

The sub fence (A) can be installed on the right side of the guide fence. Insert

the rods of the sub fence (A) into the holes in the guide fence. Tighten the

6mm knob bolt which come with the sub fence (A) to secure the sub fence

(A). Then, you can realize stable cutting of the material with a wide back

face.

10. Position adjustment of laser line (Only Model C10FSH)

WARNING: * Make sure before plugging the power plug into the receptacle that the main body

and the laser marker are turned oﬀ .

* Exercise utmost caution in handling a switch trigger for the position adjustment of

the laser line, as the power plug is plugged into the receptacle during operation.

If the switch trigger is pulled inadvertently, the saw blade can rotate and result in

unexpected accidents.

* Do not remove the laser marker to be used for other purposes.

CAUTION:

Fig. 17

Fig. 16

* Laser radiation- Do not stare into beam.

* Laser radiation on work table. Do not stare into beam.

If your eye is exposed directly to the laser beam, it can be hurt.

* Do not dismantle it.

* Do not give strong impact to the laser marker (main body of tool); otherwise, the

position of a laser line can go out of order, resulting in the damage of the laser

marker as well as a shortened service life.

* Keep the laser marker lit only during a cutting operation. Prolonged lighting of the

laser marker can result in a shortened service life.

* Use of controls or adjustments or performance of procedures other than those

speciﬁ ed herein may result in hazardous radiation exposure.

NOTE: * Perform cutting by overlapping the ink line with the laser line.

* When the ink line and the laser line are overlapped, the strength and weakness of light

will change, resulting in a stable cutting operation because you can easily discern the

conformity of lines. This ensures the minimum cutting errors.

* In outdoor or near-the-window operations, it may become diﬃ cult to observe the laser

line due to the sunlight. Under such circumstances, move to a place that is not directly

under the sunlight and engage in the operation.

* Do not tug on the cord behind the motor head or hook your ﬁ nger, wood and the like

around it; otherwise, the cord may come oﬀ and the laser marker may not be lit up.

Sub Fence

(A)

6mm Knob

Bolt

Fig. 15

17

English

Ink lining can be easily made on this tool to the laser marker. A switch

lights up the laser marker. (Fig. 18)

Depending upon your cutting choice, the laser line can be aligned with

the left side of the cutting width (saw blade) or the ink line on the right

side.

The laser line is adjusted to the width of the saw blade at the time of

factory shipment. Adjust the positions of the saw blade and the laser line

taking the following steps to suit the use of your choice.

(1) Light up the laser marker and make a groove of about 3/16" (5mm)

deep on the workpiece that is about 25/32" (20mm) in height and

5-29/32"(150mm) in width. Hold the grooved workpiece by vise as it

is and do not move it. For grooving work, refer to “11.Groove cutting

procedures” on page 25.

(2) Then, turn the adjuster and shift the laser line. (If you turn the

adjuster clockwise, the laser line will shift to the right and if you turn it

counterclockwise, the laser line will shift to the left.) When you work

with the ink line aligned with the left side of the saw blade, align the

laser line with the left end of the groove. (Fig. 20) When you align it

with the right side of the saw blade, align the laser line with the right

side of the groove.

(3) After adjusting the position of the laser line, draw a right-angle ink

line on the workpiece and align the ink line with the laser line. When

aligning the ink line, slide the workpiece little by little and secure it

by vise at a position where the laser line overlaps with the ink line.

Work on the grooving again and check the position of the laser line.

If you wish to change the laser line’s position, make adjustments

again following the steps from (1) to (3).

NOTE: Check and make sure on a periodic basis if the position of the laser line is in order. As

regards the checking method, draw a right-angle ink line on the workpiece with the height

of about 25/32" (20mm) and the width of 5-29/32"(150mm), and check that the laser line is

in line with the ink line [The deviation between the ink line and the laser line should be less

than the ink line width (0.5mm)]. (Fig. 21)

Switch

Laser line

Saw Blade

Marking

(pre-marked)

Workpiece

Cutting Width

Fig. 18

Fig. 19

Marking

(pre-marked)

Vise Assembly

Turn

Move

Laser Line

Groove

Adjuster

Laser Line

Fig. 20

Fig. 21

18

English

PRACTICAL APPLICATIONS

WARNING: * To avoid personal injury, never remove or place a workpiece on the table while the

tool is being operated.

* Never place your limbs inside of the line next to warning sign while the tool is being

operated. This may cause hazardous conditions (see Fig. 22).

Line

Warning Sign

Line

Warning Sign

Fig. 22

1. Switch operation

The trigger switch lock-oﬀ button is designed to prevent inadvertent operation

of the power tool. To operate the power tool, it is necessary to ﬁ rst fully insert

the lock-oﬀ button into the hole on the handle as shown in Fig. 23.

The trigger switch will not operate unless the lock-oﬀ button has been pushed

in.

When the trigger switch is released, the power goes oﬀ and the lock-oﬀ button

automatically returns to its initial position, locking the trigger switch.

WARNING: Always remove the lock-oﬀ button from the handle when the power tool is not in

use. This will ensure that the power tool cannot be turned on accidentally or by

someone (especially a child) who is not qualiﬁ ed to use the power tool. If the lock-

oﬀ button is left in the handle, serious personal injury can result. Since the lock-oﬀ

button ﬁ ts rather tightly, it may be necessary to turn it to the left and right during

mounting and removing.

2. Using the Vise Assembly (Standard accessory)

The vise assembly can be mounted on either the left fence (Fence (B))

or the right fence (Fence (A)), and can be raised or lowered according

to the height of the workpiece.

To raise or lower the vise assembly, ﬁ rst loosen the 6mm knob bolt. As

shown in Fig. 24, the vise shaft has three locking grooves into which

the tip of the 6mm wing bolt is designed to ﬁ t in order to lock the screw

holder in the desired position.

To ensure that the tip of the 6mm wing bolt is properly aligned with the

desired locking groove on the vise shaft, simply align the upper surface

of the fence to either of three v-grooves on the vise shaft surface or to

the lower surface of the screw holder.

Therefore, the vise assembly can be attached in either of three

positions to ensure proper height adjustment.

After adjusting the height, ﬁ rmly tighten the 6mm wing bolt; then turn

the upper knob, as necessary, to securely attach the workpiece in

position.

CAUTION: Always conﬁ rm that the motor head (see Fig. 1) does not contact the vise assembly

when it is lowered for cutting. If there is any danger that it may do so, loosen the

8mm knob bolt slightly and move the vise assembly to a position where it will not

contact the saw blade.

Fig. 23

Handle

Trigger

Switch

Lock-oﬀ Button

Hole

Fig. 24

Screw Holder

Knob

Work piece

Vise

Plate

Groove

6mm

Knob Bolt

Fence

6mm Knob Bolt

V-Groove

19

English

In case of compound cutting of left bevel angle and left miter angle, a workpiece of

up to 2-3/16" (55mm) can be ﬁ xed with a vise assembly mounted on the left side. In

case the workpiece height exceeds 2-3/16" (55mm), mount the vise assembly on the

opposite side of the inclination of the motor head. For other compound cutting (left

bevel + right miter, right bevel + left miter and right bevel + right miter), mount the

vise assembly on the opposite side of the inclination of the motor head to avoid the

contact of the vise assembly with the motor head.

3. Cutting Operation

(1) As shown in Fig. 25 the width of the saw blade is the

width of the cut. Therefore, slide the workpiece to the right

(viewed from the operator’s position) when length

is

desired, or to the left when length

is desired.

(Only Model C10FSH)

If a laser marker is used, align the laser line with the left

side of the saw blade, and then align the ink line with the

laser line.

(2) Once the saw blade reaches maximum speed, push the

handle down carefully until the saw blade approaches the

workpiece.

(3) Once the saw blade contacts the workpiece, push the

handle down gradually to cut into the workpiece.

(4) After cutting the workpiece to the desired depth, turn the

power tool OFF and let the saw blade stop completely

before raising the handle from the workpiece to return it to

the full retract position.

CAUTION:

* Increased pressure on the handle will not increase the cutting speed.

On the contrary, too much pressure may result in overload of the motor and/or

decreased cutting eﬃ ciency.

WARNING: * Conﬁ rm that the trigger switch is turned OFF and the power plug has been removed

from the receptacle whenever the tool is not in use.

* Always remove the lock-oﬀ button from the handle and store it in a secure place

after completing the work.

* Always turn the power oﬀ and let the saw blade stop completely before raising the

handle from the workpiece.

If the handle is raised while the saw blade is still rotating, the cut-oﬀ piece may

become jammed against the saw blade causing fragments to scatter about

dangerously.

* Every time one cutting or deep-cutting operation is ﬁ nished, turn the switch oﬀ ,

and check that the saw blade has stopped. Then raise the handle, and return it to

the full retract position.

* Be absolutely sure to remove the cut material from the top of the turntable, and

then proceed to the next step.

* Continued cutting operation can result in overload of the motor. Touch the motor

and if it’s hot, stop your cutting operation once and rest for 10 minutes or so, and

then restart your cutting operation.

4. Cutting narrow workpieces (Press cutting)

Slide the hinge down to holder (A), then tighten the slide securing knob (see

Fig. 2) as indicated in Fig. 26.

Lower the handle to cut the workpiece.

Using the power tool this way will permit cutting of workpieces of up to 3-11/32"

(85mm) square.

Fig. 25

Adjusting Line

Marking

(pre-marked)

Marking

(pre-marked)

(Front View)

Hinge

Holder (A)

Handle

Press

Down

Workpiece

Fig. 26

20

English

5. Cutting large workpieces

There may be case when a complete cutting cannot be done depending on the

height of workpiece. In this case, mount an auxiliary board with the 6mm ﬂ at

head screws and the 6mm nuts using the 7mm holes on the fence surface (two

holes on each side). (Fig. 27)

Refer to page 9 “SPECIFICATIONS” for the thickness of the auxiliary board.

6. Cutting wide workpieces (Slide cutting)

(1) Workpieces up to 3-11/32" (85mm) high and 12-9/32" (312mm) wide:

Loosen the slide securing knob (see Fig. 2), grip the handle and

slide the saw blade forward.

Then press down on the handle and slide the saw blade back to

cut the workpiece as indicated in Fig. 28. This facilitates cutting

of workpieces of up to 3-11/32" (85mm) in height and 12-9/32"

(312mm) in width.

(2) Workpieces up to 3-9/16" (90mm) high and 11" (280mm) wide:

Workpieces of up to 3-35/64" (90mm) in height and up to 11"

(280mm) in width can be cut in the same manner as described in

paragraph 6-(1) above.

CAUTION:

* When cutting a workpiece of 3-11/32" (85mm) height, adjust the lower limit position

of the motor head so that the gap between the lower edge of the motor head and

the workpiece will be 3/32" to 1/8" (2 to 3mm) at the lower limit position.

* If the handle is pressed down with excessive or lateral force, the saw blade may

vibrate during the cutting operation and cause unwanted cutting marks on the

workpiece, thus reducing the quality of the cut.

Accordingly, press the handle down gently and carefully.

* In slide cutting, gently push the handle back (rearwards) in a single, smooth

operation.

Stopping the handle movement during the cut will cause unwanted cutting marks

on the workpiece.

WARNING: * For slide cutting, follow the procedures indicated above in Fig. 28.

Forward slide cutting (toward the operator) is very dangerous because the saw

blade could kick upward from the workpiece. Therefore, always slide the handle

away from the operator.

* Always return the carriage to the full rear position after each crosscut operation

in order to reduce the risk of injury.

* Never put your hand on the side handle during the cutting operation because the

saw blade comes close to the side handle when the motor head is lowered.

7. Bevel cutting procedures

(1) Loosen the clamp lever and bevel the saw blade to the left or to the

right.

When tilting the motor head to the right pull the ﬁ xing pin towards the

rear.

The clamp lever adopts a latchet system. When contacting the work

bench and the main body, pull the clamp lever in the direction of the

arrow mark as illustrated in Fig. 29, and change the direction of the

clamp lever.

(2) Adjust the bevel angle to the desired setting while watching the bevel

angle scale and indicator, then secure the clamp lever.

Fence

6mm Nut

6mm Flad Hd.

Screw

Auxiliary

Board

Fig. 27

Handle

2 Press

Down

Workpiece

1 Pull Forward

3 Push Rearward to Cut

▲

Fig. 28

Fixing pin

Clamp Lever

Tighten

Bevel Scale

Fig. 29

Holder (A)

Pull

Indicator

(for left bevel scale)

Loosen

La page charge ...

Hitachi C 10FSH Safety Instructions And Instruction Manual

Ce manuel convient également à

Hitachi C 10FSH Safety Instructions And Instruction Manual

dans d''autres langues

Documents connexes