KitchenAid KWCU300WSS0 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KWCU300WSS0

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

Kitchen_kid ®

30" (76.2 CM), 36" (91.4 CM), 42" (106.7 CM)AND

48" (121.9 CM) COMMERCIAL STYLE

WALL-MOUNT CANOPY RANGE HOOD

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

or visit our website at www, kitchenaid,com

In Canada, for assistance, installation and service, call: 1-800-807-6777

or visit our website at www, kitchenaid,ca

HO'I'I'E D'EXTRACTION A MONTAGE MURAL

DE STYLE COMMERCIAL DE 30" (76,2 CM),

36" (91,4 CM), 42" (106,7 CM) ET 48" (121,9 CM)

Au Canada, pour assistance, installation ou service composez le 1-800-807-6777

ou visitez notre site web & www, kitchenaid,ca

Para obtener acceso al manual de uso y cuidado en espafiol, o para obtener informacion adicional acerca de su producto,

visite: www.kitchenaid.com.

Tenga listo su n0mero de modelo completo. Puede encontrar el n0mero de modelo y de serie dentro de la cavidad superior de la

puerta.

Table of Contents/Table des matieres ............................................................................. 2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RI'-=SIDENTIELLE UNIQUEMENT.

W10233972A

TABLEOF CONTENTS

RANGE HOOD SAFETY ................................................................. 3

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 5

Venting Requirements .................................................................. 6

Electrical Requirements ............................................................... 7

INSTALLATION INSTRUCTIONS .................................................. 8

Prepare Location .......................................................................... 8

Change Hood to Optional Rear Exhaust ..................................... 8

Install Range Hood ..................................................................... 10

Make Electrical Connection ....................................................... 10

Install Grease Filters ................................................................... 11

Check Operation ........................................................................ 11

RANGE HOOD USE ...................................................................... 11

Range Hood Controls ................................................................ 11

RANGE HOOD CARE ................................................................... 12

Range Hood Lamps ................................................................... 12

Cleaning ...................................................................................... 12

WIRING DIAGRAM ....................................................................... 13

ASSISTANCE OR SERVICE ......................................................... 14

Accessories ................................................................................ 14

WAR RANTY ............................................................................... 15

TABLE DES MATIERES

SI_CURITI_ DE LA HOTTE DE CUlSINIF:RE ............................... 16

EXIGENCES D'INSTALLATION ................................................... 18

Outillage et pieces ...................................................................... 18

Exigences d'emplacement ......................................................... 18

Exigences concernant I'evacuation ........................................... 19

Specifications electriques .......................................................... 20

INSTRUCTIONS D'INSTALLATION ............................................. 21

Preparation de I'emplacement ................................................... 21

Modification de la hotte pour evacuation par

I'arriere facultative ...................................................................... 21

Installation de la hotte ................................................................ 23

Raccordement electrique ........................................................... 23

Installation des filtres a graisse .................................................. 24

Contr61e du fonctionnement ...................................................... 24

UTILISATION DE LA Ho'n'E ....................................................... 24

Commandes de lahotte de cuisiniere ....................................... 24

ENTRETIEN DE LA HOTTE DE CUlSINIF:RE ............................. 25

Lampes de lahotte de cuisiniere ............................................... 25

Nettoyage ................................................................................... 25

SCHI_MA DE C.&,BLAGE............................................................... 26

ASSISTANCE OU SERVICE ......................................................... 27

Accessoires ................................................................................ 27

GARANTIE ..................................................................................... 28

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

• Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

• Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

• Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

• Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

• When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

• Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

[] Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

[] Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

[] Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

[] Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

[] NEVER PICK UP A FLAMING PAN -you may be burned.

[] DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

[] Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

[] WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

SAVE THESE iNSTRUCTiONS

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Level

• Drill

• 1W' (3 cm) drill bit

• 1/8"(3 mm) drill bit if installing into wood and a 5/_e"(8 mm) drill

bit if installing optional backsplash kit.

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Pliers

• Vent clamps

• Jigsaw or keyhole saw

• Flat-blade screwdriver

• Metal snips

• Phillips screwdriver

• Scissors

Parts needed

• Home power supply cable

• 1 - 1/2"(12.7 mm) UL listed or CSA approved strain relief

• 2 UL listed wire connectors

• 1 wall or roof cap

• Metal vent system

• Caulking gun and weatherproof caulking compound

Parts supplied

Remove parts from packages. Check that all parts are included.

• 2 metal grease filters for 30" (76.2 cm) models

3 metal grease filters for 36" (91.4 cm) models

3 metal grease filters for 42" (106.7 cm) models

4 metal grease filters for 48" (121.9 cm) models

• 2 mounting brackets with adjustment screws installed

• 2 mounting bracket screws

• 4 washer head Phillips mounting screws

• Damper

• 2 dampers for 48" (121.9 cm) model.

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located inside the range hood on the rear wall of the

range hood.

Canopy range hood location should be away from strong draft

areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

The canopy range hood is factory set for venting through the roof

or through the wall.

All openings in ceiling and wall where canopy range hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

Vented Installations

30" (76.2

36" (91.4 cm),

42" (106.7 crn) or

48" (121.9 cm)

18" (45.7 cm)

(63.5 cm)

Optional Full-Width Duct Cover Installations

12"

._(30.5crn)

12"

18"

Optional Telescopic Chimney Kit Installations

117A_" 24z/8.

(29.o (63.2cm>

Installation Dimensions

30"(76.2cm),36" (91.4crn),

42" (106.7cm)or 48"(121.9crn)

cabinetopeningwidth

(Ifinstalledbetweencabinets

3s"(91.4cm)

countertopheight

18"(45.7crn)

clearanceupper

cabinettocountertop

A. 84" (213.4 cm) minimum for

installations with canopy only.

B. 96" (243.8 cm) minimum for

installations with optional

duct cover or telescopic

chimney kit.

IMPORTANT:

Minimum distance "X": 30" (76.2 cm)

Suggested maximum distance "X": 36" (91.4 cm)

Vent system must terminate to the outdoors.

Do not terminate the vent system in an attic or other enclosed

area.

• Do not use 4" (10.2 cm) laundry-type wall caps.

• Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

• The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps to seal all joints in the vent system.

The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

• Use caulking to seal exterior wall or roof opening around the

cap.

• The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup air

Local building codes may require the use of make up air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Methods

A 6" (15.2 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 6" (15.2 cm) round. Two

6" (15.2 cm) round vent systems are needed for installation on

48" (121.9 cm) models.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. The

exhaust collar can also be directed to vent out the rear of the

hood.

To vent through the wall, the blower needs to be changed to the

proper orientation.

Roof Venting Wall Venting Rear Venting

//'

A. Roof cap A. Waft cap A. Waft cap

B. 6" (15.2 cm) B. 6" (15.2 cm) B. 6" (15.2 cm)

round vent* round vent* round vent*

*The 48" (121.9 cm) hood uses two 6" (15.2 cm) round vents or

transitions to 10" (25.4 cm) round vent using Part Number

4396915.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece Equivalent Length

45° elbow 2.5 ft

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

The maximum equivalent vent lengths are:

6" (15.2 cm) round vent - 35 ft (10.7 m)

7" (17.8 cm) round vent - 40 ft (12.2 m)

8" (20.3 cm) round vent - 50 ft (15.2 m)

9" (22.9 cm) and 10" (25.4 cm) round vents - 60 ft (18.3 m)

Example vent system

90° elbow I-_ 6. (1.6m)-_l Wall cap

/ I

(0.6rn)

Thefollowing example falls within the maximum recommended

vent length.

1 - 90° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSl/NFPA 70 (latest

edition), or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

• If the house has aluminum wiring follow the procedure below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

• Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate.

The model/serial plate is located behind the filter on the rear

wall of the hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSl/NFPA 70 (latest edition), or CSA

Standards C22.1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

INSTALLATION INSTRUCTIONS

• It is recommended that the vent system be installed before

hood is installed.

• Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

• Check that all installation parts have been removed from the

shipping carton.

1. Disconnect power.

2. Determine which venting method to use: roof, wall or rear

exhaust.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 ormore people, lift range hood onto covered surface.

Optional Backsplash Installation

The following instructions are for the backsplash without shelves.

Ifyou are installing the Optional Backsplash with Shelves for Heat

Lamps, follow the instructions included with that product.

The hardware package supplied with the kit includes 4 plastic

wall anchors and mounting screws.

NOTE: The minimum height of the hood above the cooktop is

30" (76.2 cm). The backsplash can be extended from 1923/32''

(50.1 cm) to 39" (99.1 cm). As the 30" (76.2 cm) installation

height increases, the hood's capture area decreases.

• Determine height of the hood.

• For ease of installation, use 2 or more people to position the

backsplash on the wall so that the top of the backsplash is at

the height of the bottom edge of the hood. Mark the location

of the four corner holes. It is recommended that the

backsplash be attached to the wall at all four corners.

However, the lower flange can be secured between the wall

and backspash, countertop or cabinet base without using the

bottom corner screws.

• Drill 5A6"(8 mm) holes.

• Push plastic wall anchors all the way into the holes.

• Position the holes in the backsplash over the wall anchors

and attach using the screws supplied.

The hood comes from the factory with the exhaust collar on top

of the hood. The hood exhaust may be directed out the rear of

the hood through the exhaust collar. If you desire to have the

hood exhaust out the rear, follow the procedure below.

1. From inside the hood, unplug wire attached to blower motor.

A.Blower motor

B.Blower motor plug

2. Turn the hood over and remove the screws holding the

exhaust blower assembly to the hood.

A. Blower motor

B.Screws

3. Rotate the blower assembly so that the exhaust collar is

facing out the back of the hood.

A.Exhaust blower assembly

B.Screws

C.Exhaust collar

4. Replace the screws holding the blower assembly to the hood.

5. Plug the blower motor wire back into the blower motor.

Range Hood Mounting Screws Installation

• The hood attaches to the wall with two mounting brackets

with adjustment screws and four mounting screws.

1. Determine and mark the centerline on the wall where the

canopy range hood will be installed.

2. Select a mounting height between a minimum of 30" (76.2 cm)

and a suggested maximum of 36" (91.4 cm), above the

cooking surface and the bottom of the range hood. To this

distance, add 16" (40.6 cm) and mark a horizontal line.

3. Mark 2 points on each side of the horizontal line the distance

shown in "A" below (based on the size of your range hood).

B C

A. Distance from center of mounting

bracket to centerline.

30" (76.2 cm) hood:

13_" (34.0 cm)

36" (91.4 cm) hood:

16_" (41.6 cm)

42" (106. 7 cm) hood:

19 _" (49.4 cm)

48" (121.9 cm) hood:

22_" (56.8 cm)

B. Mounting screws (4)

C. Mounting brackets and

adjustment screws

D. Bottom of hood

Adjust the two adjusting screws on the mounting brackets to

the lowest point and attach to the wall with the screws

provided. The screws provided for mounting this hood must

be fastened into solid wood. Do not fasten into sheet rock

only.

Optional Duct Cover Installation

1. Attach the full-width duct cover to the top of the range hood

with the screws provided. The duct cover must be attached

to the top of the range hood before mounting the range hood

to the wall. For information on ordering the optional duct

cover, see "Accessories" section.

A. Distance from center of mounting

bracket to centerline.

30" (76.2 cm) hood:

13 r_2" (34.2 cm)

36" (91.4 cm) hood:

16 r_2" (41.8 cm)

42" (106. 7 cm) hood:

191_2" (49.4 cm)

48" (121.9 cm) hood:

22 r_2" (57.1 cm)

B. Mounting brackets

C. Top of hood

2, Install each bracket on the wall as shown. Make sure the

screws and brackets are securely fastened to the wall.

IMPORTANT: Install only the brackets. Do not install the

hood.

Optional Chimney Extension Installation

1. If a chimney extension is used, attach the extension brackets

as shown. Make sure that the screws are securely fastened to

the wall. For information on ordering the optional chimney

extensions, see "Accessories" section.

10%" ,//

(27 cm) //

/ _ / / / A / / / / / / / / J'/// / / / /

_ _ __ _ _ "_

i i i/

1ow,o"__ 10,5/,o"

(27.8cm) (27.8cm)

23" (58.4 crn) max.

12" (30.5 cm) min.

k ///C

A. Ceiling

B. Brackets

C. Top of hood

Optional Heat Lamp Installation

1. Remove the bottom panel at the rear of the hood by removing

the screws located at each end.

2. Install the heat lamp kit with the tabs inserted into the

corresponding slots on the hood and the screws toward the

front of the hood. Replace the screws to secure it in place.

Complete Preparation

1. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the range

hood. See the "Venting Requirements" section.

2. Determine the location where the power supply cable will be

run through the wall.

3. Drill a 1V4"(3.2 cm) hole at this location.

4. Pull enough power supply cable through the wall to allow for

easy connection to the terminal box.

5. If roof or wall cap does not have a damper, attach damper to

exhaust opening(s) on top of the hood using two Phillips-

head screws.

6. If 48" (121.9 cm) hood is to be connected to 10" (25.4 cm)

round vent system, install the vent transition piece now.

Thehoodattachestothewallbyscrewsdiscussedinthe

"PrepareLocation"section.

1. Using2ormorepeople,hangtherangehoodonthetwo

mountingbracketsandadjustthemountingbracketsfrom

insidethehoodtomakethehoodlevel.

IMPORTANT:Makesurethattherangehoodissecurely

tightenedagainstthewall.

2. Installthemountingscrewsintothewalluntilthescrewheads

aretight.Thescrewsprovidedformountingthishoodmust

befastenedintosolidwood.Donotfastenintosheetrock

only.

3. Connectventsystemtohood.Sealalljointswithclamps.

4. Ifyourinstallationusestheoptionalductcover,fitthecover

flangesoverthebrackets.Ifinstallationusesthechimney

extension,fittheextensionoverthebrackets.Installthe

uppersectionfirst,thenfitthelowersectionovertheupper

section.Sealextensiontohoodwithclamps.

;k,.9 1 R: _.._¢.111

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Remove terminal box cover.

3. Remove the knockout in the terminal box and install a UL

listed or CSA approved V2"strain relief.

Run 3 wires, black, white, green or bare, through strain relief

into terminal box. Use caulking to seal openings.

-q

...............

A. Home power supply cable

B. Black wires

C. UL fisted wire connectors

D. White wires

Green (or bare) ground wire from home

power supply connected to green ground

screw

Range hood power supply cable

5. Use UL listed wire connectors and connect black wires (B)

together.

6. Use UL listed wire connectors and connect white wires (D)

together.

7. If optional heat lamp kit is used, connect black wires from

heat lamp with black wires from home power with UL listed

wire connectors. Connect white wires from optional heat

lamp kit to home power with UL listed wire connectors.

Fire Hazard

Electrically ground the blower.

Use copper wire.

Connect ground wire to green ground screw in

terminal box.

Failure to do so can result in death, fire, or

electrical shock.

8. Connect green (or bare) ground wire from home power supply

to the unused green ground screw (E) in the terminal box.

9. Tighten strain relief screws.

10. Install terminal box cover.

11. Check all light bulbs to make sure they are secure in their

sockets.

12. Reconnect power.

NOTE: Use 2 hands to install filter, one to pull and turn the knob,

the other to hold the filter in place so that it doesn't fall.

1. Insert back edge of filter into rear channel of the filter

opening.

2. Pull out on knob and turn counterclockwise, position front

edge into place and release knob.

3. Repeat for remaining filters.

( , 'I :>'[l_i .......................

Check operation of the range hood by turning on the power.

The range hood controls are located on the right-hand

underside of the range hood.

3. Move the light switch to "1" position. The lights should turn

on.

4. Move blower switch to "1" position. The blower should

operate.

5. Move the blower speed switch to "1" position for low speed,

"2" position for medium speed or "3" position for high speed.

6. Move blower and light switches to "0" position to turn blower

and light off.

7. If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

Disconnect power supply and check that the wiring is

correct.

NOTE: To get the most efficient use from your new range hood,

read the "Range Hood Use" section.

A. Controls

B. Filters

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

The hood controls are located on the right-hand underside of the

range hood.

2. Move the light switch to the "0" position to turn range hood

light OFR

Operating the blower

1. Move the blower switch to the "1" position to turn the blower

ON. The blower will begin operating at the speed set on the

blower speed switch.

2. Move the blower switch to the "0" position to turn the blower

OFR

Adjusting the blower

The blower has 3 speed controls. Move the blower speed switch

to "1" position for low speed, "2" position for medium speed or

"3" position for high speed.

B C D

A. Controls

B. Light switch

C. Blower switch

D. Blower speed switch

Operating the light

1. Move the light switch to the "1" position to turn range hood

light ON.

Operating the heat lamp (optional accessory)

1. Install heat lamp bulbs (not included) into heat lamp sockets.

NOTE: Heat lamp bulbs should be rated to a maximum of

250 watts each.

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

To turn on a light, move the switch in the heat lamp panel

closest to the desired light into the "1" position. Move the

switch into the "0" position to turn off the light. Repeat with

the other light.

RANGE HOOD CARE

.... .....[

Replacing a Halogen Lamp

This hood uses 12-volt, 20-watt halogen lamps.

Turn off the range hood and allow the halogen lamps to cool.

To avoid damage or decreasing the life of the new bulb, do not

touch bulb with bare fingers. Replace bulb using tissue or

wearing cotton gloves to handle bulb.

To Replace:

1. Disconnect power.

2. Remove 2 screws from the circular metal trim around the

lamp assembly.

3. Pull the trim and lamp assembly down far enough so that the

lamp can be pulled out of the socket clips.

A. Remove 2 screws.

B. Pull trim with lamp assembly down.

Always wipe dry to avoid water marks.

• Stainless Steel Cleaner and Polish.

• Mild liquid detergent and water.

• Wipe with damp soft cloth or nonabrasive sponge, then rinse

with clean water and wipe dry.

Metal Filters:

For vented installations, use 2 hands to remove filters. Turn the

knob to the left (counterclockwise) to release filter. Repeat with

other filter.

Wash metal filters as needed in dishwasher or hot detergent

solution to clean.

Reinstall the filter by placing the back edge in the channel at rear

of hood. Push filter into place, turn the knob to the right

(clockwise) to attach to range hood. Repeat with other filter.

4. Insert the new lamp into the socket clips and push the lamp

assembly back up into the hood.

5. Replace the screws.

6. Reconnect the power.

Exterior surfaces:

To avoid damage to the exterior surface,do not use steel wool or

soap-filled scouring pads. Rub in direction of the grain line to

avoid scratching the surface.

Thermal Protector

The range hood is equipped with athermal protector to avoid

overheating conditions. If the range hood shuts off while in use,

move the blower slider switch to the 0 position to turn off the

range hood. Wait approximately 60 minutes, then move the

blower slider switch to the 1 position to restart the range hood.

WIRING DIAGRAM

BF[ i _ @ BU

i'<- co

i @}} _h

BK i2 _ w

I................................W........................................................................................................

o o ::_

_ _ V rD

W '_ <_k ' _ <_,i I_i_.................

:! Ii*GY _ _ _t _,.#__i....

....................BK...................._ ,_/,_y_::::ii BU

J_ W

I........................................BU.................... _.

; ........................ _---_

i R

_" ? Y i'

m /_,A

/ V

/ / , ,

I _-

U3 I

i i...................................................................................................................................... i I

i W ,

..................................................................................................................................................... I

BK i i

i.................................................................................................................................................................................................................................................................................................................................................................i i

ASSISTANCE OR SERVICE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance. To locate factory

specified replacement parts in your area, call us or your nearest

designated service center.

ii] iI'-_:_ I _;;(i!!I

Call the KitchenAid Customer eXperience Center toll free:

1-800-422-1230.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

• Referrals to local dealers, repair parts distributors and service

companies. KitchenAid designated service technicians are

trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the KitchenAid designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

Call the KitchenAid Canada Customer eXperience Centre toll

free: 1-800-807-6777.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Referrals to local dealers, repair parts distributors and service

companies. KitchenAid Canada designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to KitchenAid

Canada with any questions or concerns at:

Customer eXperience Centre

KitchenAid Canada

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

Full-Width Duct Cover

Order Part Number 8285149 for 30" (76.2 cm) model

Order Part Number 8284753 for 36" (91.4 cm) model

Order Part Number 8284828 for 42" (106.7cm) model

Order Part Number 8284752 for 48" (121.9 cm) model

For further assistance

If you need further assistance, you can write to KitchenAid with

any questions or concerns at:

KitchenAid Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

Telescopic Chimney Kit

Order Part Number 8284754

Heat Lamp Kit

Order Part Number W10238212 for 30" (76.2 cm) model

Order Part Number W10238211 for 36" (91.4 cm) model

Order Part Number W10238211 for 42" (106.7cm) model

Order Part Number W10238209 for 48" (121.9 cm) model

Backsplash Kit (without heat lamp)

Order Part Number 8285148 for 30" (76.2 cm) model

Order Part Number 8284756 for 36" (91.4 cm) model

Order Part Number 8284827 for 42" (106.7cm) model

Order Part Number 8284755 for 48" (121.9 cm) model

Backsplash Kit (with heat lamp)

Order Part Number W10225950 for 30" (76.2 cm) model

Order Part Number W10225949 for 36" (91.4 cm) model

Order Part Number W10225949 for 42" (106.7cm) model

Order Part Number W10225948 for 48" (121.9 cm) model

KITCHENAID ®VENTILATION WARRANTY

LIM ITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, KitchenAid brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "KitchenAid") will pay for

Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a KitchenAid

designated service company. This limited warranty is valid only in the United States or Canada and applies only when the major

appliance is used in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not

apply. Proof of original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is

contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by KitchenAid.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to KitchenAid within 30 days from the date of purchase.

6. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be

repaired in the home and only in-home service is covered by this warranty.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized KitchenAid servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

10. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty

is void if the factory applied serial number has been altered or removed from your major appliance.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized KitchenAid dealer to determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," you may find

additional help by checking the "Assistance or Service" section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada,

call 1-800-807-6777. 9/07

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

p p

SECURITE DE LA HOTTE DE CUISINIERE

Votre securit6 et celle des autres est tres importante.

Nous donnons de nombreux messages de s6curit6 importants dans ce manuel et sur votre appareil m6nager. Assurez-vous de

toujours lire tousles messages de s6curit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit&

Ce symbole d'alerte de s6curit6 vous signale les dangers potentiels de d6c6s et de blessures graves & vous

et & d'autres.

Tousles messages de s6curit6 suivront le symbole d'alerte de s6curit6 et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d6ces ou de blessure grave si vous ne

suivez pas imm6diatement les instructions.

Risque possible de d6cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tousles messages de s6curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES iNSTRUCTiONS DE SECURITE

AVERTISSEMENT : POUR REDUIRE LE RISQUE

D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

m Utiliser cet appareil uniquement dans les applications

envisag6es par le fabricant. Pour toute question, contacter

le fabricant.

m Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre I'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour emp6cher tout r6tablissement accidentel de

I'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une 6tiquette d'avertissement pro6minente

interdisant le r6tablissement de I'alimentation.

m Tout travail d'installation ou c&blage 61ectrique doit 6tre

r6alis6 par une personne qualifi6e, dans le respect des

prescriptions de tousles codes et normes applicables, y

compris les codes du b&timent et de protection contre les

incendies.

m Une source d'air de d6bit suffisant est n6cessaire pour le

fonctionnement correct de tout appareil & gaz (combustion

et 6vacuation des gaz & combustion par la chemin6e), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de 1'6quipement de chauffage et

les prescriptions des normes de s6curit6 - comme celles

publi6es par la National Fire Protection Association (NFPA)

et I'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorit6s r6glementaires locales.

m Lors d'op6rations de d6coupage et de perqage dans un mur

ou un plafond, veiller & ne pas endommager les c&blages

61ectriques ou canalisations qui peuvent s'y trouver.

m Les ventilateurs d'6vacuation doivent toujours d6charger

I'air & I'ext6rieur.

MISE EN GARDE : Cet appareil est con£:u uniquement

pour la ventilation g6n6rale. Ne pas I'utiliser pour I'extraction

de mati_res ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et 6vacuer ad6quatement les gaz, veiller & acheminer I'air

aspir6 par un conduit jusqu'b, I'ext6rieur - ne pas d6charger

I'air aspir6 dans un espace vide du b&timent comme une

cavit6 murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR R¢:DUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MI2TALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIF:RE :

[] Ne jamais laisser un 616ment de surface fonctionner &

puissance de chauffage maximale sans surveillance. Un

renversement/d6bordement de mati_re graisseuse pourrait

provoquer une inflammation et la g6n6ration de fum6e.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

[] Veiller &toujours faire fonctionner le ventilateur de la hotte

Iors de la cuisson avec une puissance de chauffage 61ev6e

ou Iors de la cuisson d'un mets &flamber (& savoir cr6pes

Suzette, cerise jubil6e, steak au poivre flamb6).

[] Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

[] Utiliser toujours un ustensile de taille appropri6e. Utiliser

toujours un ustensile adapt6 & la taille de 1'616ment

chauffant.

AVERTISSEMENT : POUR RC:DUIRE LE RISQUE DE

DOMMAGES CORPORELS APRF:S LE DECLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINI_:RE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :a

[] Placer sur le r6cipient un couvercle bien ajust6, une t61e &

biscuits ou un plateau m6tallique POUR ETOUFFER LES

FLAMMES, puis 6teindre le brt_leur. VEILLER ,_ ¢:VITER

LES BRULURES. Si les flammes ne s'6teignent pas

imm6diatement, ¢:VACUER LA PIECE ET APPELER LES

POMPIERS.

[] NE JAMAIS PRENDRE EN MAIN UN RECIPIENT

ENFLAMME - vous risquez de vous brQler.

[] NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brQlante.

[] Utiliser un extincteur SEULEMENT si :

- IIs'agit d'un extincteur de classe ABC, dont on connaft le

fonctionnement.

- IIs'agit d'un petit feu encore limit6 & I'endroit oQ il s'est

d6clar6.

- Les pompiers ont 6t6 contact6s.

- IIest possible de garder le dos orient6 vers une sortie

pendant I'op6ration de lutte contre le feu.

aRecommandations tir6es des conseils de s6curit6 en cas

d'incendie de cuisine publi6s par la NFPA.

[] AVERTISSEMENT : Pour r6duire le risque d'incendie

ou de choc 61ectrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de r6glage de la vitesse & semi-

conducteurs.

CONSERVEZ CES iNSTRUCTiONS

EXIGENCES D'INSTALLATION

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Lire et suivre les instructions fournies avec les outils

indiqu6s ici.

Outils n6cessaires

• Niveau

• Perceuse

• Foret de 11¼"(3 cm)

• Foret de 1/8"(3 mm) en cas d'installation dans du bois et foret

de %e" (8 mm) en cas d'installation de I'ensemble de dosseret

facultatif.

• Crayon

• Pince & denuder ou couteau utilitaire

• Metre-ruban ou regle

• Pince

• Pistolet & calfeutrage et compose de calfeutrage resistant

aux intemperies

• Brides de serrage pour conduit d'evacuation

• Scie sauteuse ou scie &guichet

• Tournevis & lame plate

• Cisaille de ferblantier

• Tournevis Phillips

• Ciseaux

Pi6ces n6cessaires

• C&ble d'alimentation electrique du domicile

• 1 serre-c&ble de 1/2"(12,7 mm) (homologation UL ou CSA)

• 2 connecteurs de ills homologues UL

• 1 bouche de decharge (decharge & travers lemur ou & travers

le toit)

• Conduit d'evacuation metallique

Pi_ces fournies

Retirer les pieces des emballages. Verifier que toutes les pieces

sont presentes.

• 2 filtres & graisse metalliques, pour modele de 30" (76,2 cm)

3 filtres & graisse metalliques, pour modele de 36" (91,4 cm)

3 filtres & graisse metalliques, pour modele de 42" (106,7 cm)

4 filtres a graisse metalliques, pour modele de 48" (121,9 cm)

• 2 brides de montage avec vis de reglages installees

• 2 vis de bride de montage

• 4 visa rondelle Phillips

• Clapet

• 2 clapets pour modele de 48" (121,9 cm)

IMPORTANT : Observer les dispositions de tous les codes et

reglements en vigueur.

Confier I'installation de la hotte & un technicien qualifi& C'est &

I'installateur qu'incombe la responsabilite de respecter les

distances de separation specifiees sur la plaque signaletique de

I'appareil. La plaque signaletique est situee a I'interieur de la

hotte, sur la paroi arriere.

On doit toujours installer la hotte a distance des sources de

courant d'air (fen_tres, portes et bouches de chauffage).

Respecter les dimensions indiquees pour les ouvertures

decouper dans les placards. Ces dimensions tiennent compte

des valeurs minimales des degagements de separation.

Cette hotte a ete configuree & I'usine pour une decharge atravers

le toit ou a travers le tour.

Assurer I'etancheite au niveau de chaque ouverture decoupee

dans le plafond ou le tour pour I'installation de la hotte de

cuisinlere.

Installation dans une r_sidence mobile

L'installation de cette hotte doit satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, titre 24, HUD, partie 280); Iorsque

cette norme n'est pas applicable, I'installation doit satisfaire aux

criteres de la plus recente edition de la norme Manufactured

Home Installation 1982 (Manufactured Home Sites, Communities

and Setups) ANSI A225.1/NFPA 501A*, ou des codes et

reglements Iocaux.

Dimensions du produit

Installations avec d_charge a I'ext_rieur

30" (76,2

36" (91,4 cm),

42" (106,7 cm) ou

48" (121,9 cm)

18" (45,7 cm)

(63,5 cm)

Installations alternatives avec cache-conduit pleine

largeur

12"

(_,5 crn)

12"

18"

(45,7era)

Installations alternatives d'ensemble de chemin_e

t_l_scopique

11V10"

(29,0 cm) 247/8"

(63,2 cm)

12"- 23"

(30,5 cm - 58,4 cm)

12"

(30,5 crn)

Dimensions d'installation

30" (76,2 cm), 36" (91,4 cm),

42" (106,7 cm) ou48" (121,9 cm)

/argeur de/'ouverture duplacard

(si installation entre des

18"

degagemententrele

placardmuraletle

plandetravail

36" (91,4 cm)

hauteur du plan de travail

A B

IMPORTANT :

Valeur minimale de la distance "X" : 30" (76,2 cm)

Valeur maximale sugger6e pour la distance "X" :

36" (91,4 cm)

• Le systeme d'evacuation doit decharger I'air a I'exterieur.

• Ne pas terminer le systeme d'evacuation dans un grenier ou

dans un autre espace ferme.

• Ne pas utiliser une bouche de decharge murale de

4" (10,2 cm) normalement utilisee pour un equipement de

buanderie.

• Utiliser un conduit metallique uniquement. Un conduit en

metal rigide est recommand& Ne pas utiliser un conduit de

plastique ou en feuille metallique.

• La Iongueur du systeme d'evacuation et le nombre de coudes

doit _tre reduit au minimum pour fournir la meilleure

performance.

Pour un fonctionnement efficace et silencieux :

• Ne pas utiliser plus de trois coudes a 90°.

• Veiller & ce qu'il y ait une section droite de conduit de

24" (61,0 cm) ou plus entre deux coudes, si on doit utiliser

plus d'un raccord coud&

• Ne pas installer 2 coudes ensemble.

• Au niveau de chaque jointure du systeme d'evacuation,

assurer I'etanch6it6 avec les brides de serrage pour conduit.

• Le systeme d'evacuation doit comporter un clapet. Si la

bouche de decharge murale ou par le toit comporte un

clapet, ne pas utiliser le clapet fourni avec la hotte de

cuisiniere.

• Autour de la bouche de decharge & I'exterieur (par lemur ou

par le toit), assurer I'etanch6it6 avec un produit de

calfeutrage.

• La taille du conduit doit _tre uniforme.

Installations pour r_gions & climat froid

On doit installer un clapet anti-reflux additionnel _ I'arriere pour

minimiser le reflux d'air froid, et incorporer un el6ment d'isolation

thermique pour minimiser la conduction de chaleur par

I'intermediaire du systeme d'evacuation. Le clapet anti-reflux doit

_tre place du c6te air froid par rapport & I'el6ment d'isolation

thermique.

L'el6ment d'isolation thermique doit _tre aussi proche que

possible de I'endroit oQ le systeme d'evacuation s'introduit dans

la partie chauffee de la maison.

Air d'appoint

Les codes de b&timent Iocaux peuvent exiger I'emploi d'un

systeme d'appoint d'air Iors de I'emploi d'un ventilateur

d'extraction dont la capacite d'aspiration est superieure & un

debit (pieds cubes par minute) specifi& Le debit specifi6, en

pieds cubes par minute, est variable d'une juridiction & une autre.

Consulter un professionnel des installations de chauffage

ventilation/climatisation au sujet des exigences specifiques

applicables dans la juridiction locale.

A. 84" (213,4 cm) minimum pour

les installations avec hotte

uniquement.

B. 96" (243,8 cm) minimum pour

les installations avec cache-

conduit facultatif ou

ensemble de chemin_e

t_l_scopique.

M_thodes d'_vacuation

Un circuit d'evacuation de conduits ronds de 6" (15,2 cm) est

necessaire pour I'installation (non fourni). La hotte comporte une

ouverture de sortie de diametre 6" (15,2 cm). Deux circuits

d'evacuation ronds de 6" (15,2 cm) sont necessaires pour une

installation sur des modeles de 48" (121,9 cm).

REMARQUE • On deconseille I'emploi d'un conduit flexible. Un

conduit flexible peut causer une retro-pression et des

turbulences de I'air, ce qui reduit considerablement la

performance.

La sortie a I'exterieur du circuit d'evacuation peut se faire

travers le toit ou & travers un mur. Pour la sortie a travers un mur,

le ventilateur doit etre reorient&

Pour une evacuation a travers lemur, le ventilateur doit etre

modifie pour etre bien orient&

D_charge a D_charge a D_charge par

travers le toit travers le tour I'arri_re

A. Bouche de

d_charge sur toit

B. Conduit rond

dia. 6" (15,2 cm)*

A. Bouche de

d_charge sur toit

B. Conduit rond dia.

6" (15,2 cm)*

A. Bouche de

d_charge sur toit

B. Conduit rond dia.

6" (15,2 cm)*

*La hotte de 48" (121,9 cm) utilise deux conduits ronds de

6" (15,2 cm) ou des raccords de transition ronds de

10" (25,4 cm); utiliser la piece numero 4396915.

Calcul de la Iongueur effective du circuit d'_vacuation

Pour calculer la Iongueur effective du circuit d'evacuation

necessaire, additionner les Iongueurs equivalentes (pieds/metres)

de tousles composants utilises dans le systeme.

Composant Longueur _quivalente

Coude & 45 ° 2,5 pi

(0,8 m)

Coude & 90 ° 5 pi

(1,5 m)

Les Iongueurs equivalentes maximales sont :

Conduit rond de 6" (15,2 cm) - 35 pi (10,7 cm)

Conduit rond de 7" (17,8 cm) - 40 pi (12,2 m)

Conduit rond de 8" (20,3 cm) - 50 pi (15,2 m)

Conduits ronds de 9" (22,9 cm) et de 10" (25,4 cm) -

60 pi (18,3 m)

Exemple de syst_me de d_charge

Bouche de

Co.de0oo 0 I "o o'e

L'exemple suivant indique la Iongueur de conduit recommandee

maximum.

1 coude &90°

1 bouche de decharge

murale

Section droite de 8 pi

(2,4 m)

Longueur du systeme

= 5 pi (1,5 m)

= 0 pi (0 m)

= 8 pi (2,4 m)

= 13 pi (3,9 m)

Observer les dispositions de tous les codes et reglements en

vigueur.

L'installation electrique doit satisfaire les exigences de la plus

recente edition de lanorme National Electrical Code, ANSl/NFPA

70, ou de la norme CSA C22.1-94, Code canadien de I'electricite,

partie 1 et C22.2 N° 0-M91 (derniere edition) et de tousles codes

et reglements en vigueur.

Si les codes le permettent et si on utilise un conducteur distinct

de liaison & la terre, il est recommande qu'un electricien qualifie

verifie la qualite de la liaison & la terre.

Pour obtenir un exemplaire de la norme des codes ci-dessus,

contacter :

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• L'appareil doit etre alimente par un circuit de 120 V, CA

seulement, 60 Hz, 15 A, protege par fusible.

• Si le domicile est equipe d'un c&blage en aluminium, suivre

les instructions suivantes :

1. Connecter une section de c&ble en cuivre massif aux

conducteurs en queue de cochon.

2. Connecter le c&blage en aluminium & la section ajoutee

de c&blage en cuivre en utilisant des connecteurs et/ou

des outils specialement con(_us et homologues UL pour

fixer le cuivre a I'aluminium.

Appliquer la procedure recommandee par le fabricant des

connecteurs. La connexion aluminium/cuivre doit etre

conforme aux codes Iocaux et aux pratiques de c&blage

acceptees par I'industrie.

Le calibre des conducteurs et les connexions doivent etre

compatibles avec la demande de courant de I'appareil

specifiee sur la plaque signaletique. La plaque signaletique

de I'appareil est situee derriere le filtre, sur la paroi arriere de

la hotte.

Le calibre des conducteurs doit satisfaire les exigences de la

plus recente edition de la norme National Electrical Code,

ANSl/NFPA 70, ou de la norme CSA C22.1-94, Code

canadien de I'electricite, partie 1 et C22.2 n° 0-M91 (derniere

edition) et de tous les codes et reglements en vigueur.

La page charge ...

KitchenAid KWCU300WSS0 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KWCU300WSS0

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KWCU300WSS0 Owner's manual

KitchenAid KWCU300WSS0 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KWCU300WSS0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents