This Quick Start Guide is intended for experienced installing technicians. It is a basic reference to ensure all connections are properly made.

Models include Conekt CSR-35, CSR-6.2 and CSR-6.4. For additional information please reference Farpointe Data’s website

1.0 Introduction

A key component of a physical security electronic access control system, a mobile-ready reader combining BLE and contactless smartcard

technologies is based on RFID technology. In operation it is capable of reading data stored on a contactless smartcard credential via high

frequency—or reading data from mobile credential stored in a smartphone’s wallet app via BLE technology—and without physical contact, and

then passing the data obtained to the physical access control system. Access control systems typically manage and record the movement of

individuals through a protected area, such as a locked door.

*Plastic or metal.

3.0 Reader Wiring

Red DC (8-14 VDC) Red DC (8-14 VDC)

Green Data 0 Green Clock

White Data 1 White Data

Brown Red LEDaBrown Red LED

Orange Green LEDbOrange Green LED

comprising the physical layer of the Wiegand interface (power, ground, data 0, data 1, and/or beeper and LED). Alternatively, Belden 9539 or

similar, for all reader functions. Contact your access control system manufacturer for their specific requirements. Per the SIA’s Wiegand

specification, maximum cable length is 500 feet (152 m).

5.0 Output Formats

Wiegand (industry standard 26-bit Wiegand and custom Wiegand formats)

Magnetic Stripe (ABA Track II, clock and data, with card present)

Shield (drain) continuity must run from the reader to the access panel. Shield (drain) and reader ground must be tied together at the access panel

and connect to an earth ground at one point.

7.0 Power

Orange conductor. The LED is Red when the reader is idle and flashes when a card is

presented. The LED turns Green when the Brown Conductor is pulled low by the access

Brown conductor controls the Red LED and the Orange conductor controls the Green

LED. LED states are determined by the access control system option and capability.

and output the credential’s Card Serial Number (CSN) when the Violet conductor is

pulled low (connected to ground). Otherwise, the reader will only read and output the

credential’s programmed Sector data.

© 2018-2020 Farpointe Data, Inc. All rights reserved. Farpointe Data®,

8 to 14 VDC. 12 VDC at the reader is recommended for best operation.

9.0 Read Mode

For sector data reads, do not connect the Violet conductor (leave it high). For CSN reads, pull the Violet conductor low (connect the Violet

Connection must be done in accordance with NFPA 70. Do not connect to a receptacle controlled by a switch. Connect to a power limited DC

1. When the reader is first powered on it will beep 4-times, and the LED will shine red.

2. Presenting a supported access credential will result in the reader beeping and the LED flashing once.

Incorrect cabling Verify gauge, connections and cabling length

Not enough power 12 VDC recommended

Incorrect credential used Verify if credential technology is supported

Reader/access panel not properly grounded Earth ground needed—verify shield and reader ground are tied at access panel and connect

to ground at one point

Supply generating interference Linear power supply recommended, verify switching power supply before use

Should any of the corrective actions mentioned above not improve performance, disconnect the reader from the access panel and power it with a

separate power supply or 9VDC battery, and re-test card functionality. By powering the readers separately, most variables that may lead to

reduced performance can be eliminated. Should the problem persist, please contact Farpointe directly.

Many Farpointe Data Readers carry the following certifications:

FCC Compliance Statement: This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Caution: Changes or modifications not expressly approved by Farpointe Data could

void the user's authority to operate the equipment.

Product can be used without license conditions or restrictions in all European Union

coun-tries, including Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark,

Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania,

interference. (2) This device must accept any interference, including interference that

may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences et Développement économique Canada

applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2)

L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

Note: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

in which case the user will be required to correct the interference at his own expense.

Farpointe Data reserves the right to

change specifications without notice.