Horizon Fitness EX-58 Le manuel du propriétaire

ELLIPTICAL OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE DE L’EXERCISEUR ELLIPTIQUE

MANUAL DEL PROPIETARIO DE LA MÁQUINA ELÍPTICA

Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL.

Lire le GUIDE D’UTILISATION DE L’EXERCISEUR ELLIPTIQUE avant de se servir du présent MANUEL DU PROPRIÉTAIRE.

Lea la GUÍA DEL USUARIO DE LA MÁQUINA ELÍPTICA antes de usar este MANUAL DEL PROPIETARIO.

EX-78EX-68

GS1050E

EX-58

CE5.1

2

3 ENGLISH

36 FRANÇAIS

70 ESPAÑOL

3

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly

instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the

elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to

the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your elliptical’s serial number located on the front stabilizer tube and enter it in the space provided

below. Also locate the model name which is next to the serial number.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.

SERIAL NUMBER:

MODEL NAME: HORIZON ELLIPTICAL

WARNING

4

PIVOTING FOOT PADS

CRANK

TOP CAP

GUIDE RAIL SET

SPEAKERS

WATER BOTTLE HOLDER

UPPER HANDLEBAR

PULSE GRIPS

CONSOLE

STABILIZER TUBE

POWER CORD SOCKET

MAIN FRAME

PEDAL ARM

REAR COVER

IPOD/MP3 PLAYER POCKET

CONSOLE FAN

CONSOLE MAST

TOUCH PAD PANEL AND DISPLAY WINDOWS

LOWER HANDLEBAR

LOWER LINK ARM

EX-58

CE5.1

5

PIVOTING FOOT PADS

CRANK

TOP CAP

GUIDE RAIL SET

SPEAKERS

WATER BOTTLE HOLDER

UPPER HANDLEBAR

PULSE GRIPS

CONSOLE

REAR COVER

STABILIZER TUBE

POWER CORD SOCKET

MAIN FRAME

PEDAL ARM

IPOD/MP3 PLAYER POCKET

CONSOLE FAN

CONSOLE MAST

TOUCH PAD PANEL AND DISPLAY WINDOWS

LOWER HANDLEBAR

LOWER LINK ARM

EX-68

GS1050E

6

PIVOTING FOOT PADS

CRANK

TOP CAP

PEDAL ARM

SPEAKERS

WATER BOTTLE HOLDER

UPPER HANDLEBAR

PULSE GRIPS

CONSOLE

ON/OFF SWITCH

STABILIZER TUBE

POWER CORD SOCKET

MAIN FRAME

GUIDE RAIL SET

REAR COVER

IPOD/MP3 PLAYER POCKET

CONSOLE FAN

CONSOLE MAST

TOUCH PAD PANEL AND DISPLAY WINDOWS

LOWER HANDLEBAR

LOWER LINK ARM

INCLINE COVER

EX-78

7

TOOLS INCLUDED:

FScrewdriver

F8 mm L-Wrench

F6 mm L-Wrench

F5 mm L-Wrench

F13/15 mm Flat Wrench

PARTS INCLUDED:

F1 Main Frame

F1 Stabilizer Tube

F1 Guide Rail Set

F2 Pedal Arms

F2 Lower Handlebars

F2 Upper Handlebars

F2 Lower Link Arms With Footpads

F1 Top Cap

F1 Top Cap Rear Cover

(EX-68, EX-78 and GS1040E only)

F1 Console Mast

F1 Console Mast Boot

F1 Console

F2 Handlebar Caps

F1 Water Bottle Holder

F1 Rear Cover (EX-78 only)

F1 Audio Adapter Cable

F1 Power Cord

F7 Hardware Bags

UNPACKING

Unpack the product where you will be using it. Place the elliptical carton on a level flat

surface. It is recommended that you place a protective covering on your floor. Never

open box when it is on its side.

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and

partially threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any grease,

such as lithium bike grease is recommended.

If you have questions or if

there are any missing parts,

contact Customer Tech

Support. Contact information

is located on the back panel

of this manual.

NEED HELP?

PRE ASSEMBLY

ALL

MODELS

8

ASSEMBLY STEP 1

A Open hardware bag 1.

B Attach the stabilizer tube to the main

frame using 4 bolts (a), 4 spring

washers (b) and 4 arc washers (c).

BOLT (A)

30 mm

Qty: 4

SPRING WASHER (B)

15 mm

Qty: 4

ARC WASHER (C)

17 mm

Qty: 4

HARDWARE BAG 1 CONTENTS :

BOLTS (A)

SPRING WASHERS (B)

ARC WASHERS (C)

STABILIZER TUBE

MAIN FRAME

BOLTS (A)

SPRING WASHERS (B)

ARC WASHERS (C)

STABILIZER TUBE

MAIN FRAME

ALL

MODELS

EX-58 SHOWN

EX-78 SHOWN

9

CE5.1, EX-58, EX-68, GS1050E ASSEMBLY STEP 2

* This step is for CE5.1, EX-58, EX-68, GS1050E

models only.

A Open hardware bag 2.

B Align guide rail set with main frame as

shown.

C Attach the guide rail set to the main frame

using 4 bolts (d), 4 flat washers (e) and 4

tooth washers (g).

HARDWARE BAG 2 CONTENTS :

TOOTH WASHERS (G)

FLAT WASHERS (E)

GUIDE RAIL SET

BOLTS (D)

MAIN FRAME

CE5.1, EX-58 SHOWN

CE5.1

EX-58

EX-68

GS1050E

TOOTH WASHER (G)

15 mm

Qty: 4

FLAT WASHER (E)

17 mm

Qty: 4

BOLT (D)

55 mm

Qty: 4

10

EX-78 ASSEMBLY STEP 2

TOOTH WASHERS (G)

FLAT WASHERS (E)

GUIDE RAIL SET

BOLTS (D)

MAIN FRAME

EX-78 ONLY

EX-78

* This step is for EX-78 models only.

* CE5.1, EX-58, EX-68, GS1050E models skip to STEP 3.

A Open hardware bag 2.

B Attach the guide rail set to the main frame

using 4 bolts (d), 4 flat washers (e) and 4

tooth washers (g).

TOOTH WASHER (G)

15 mm

Qty: 4

FLAT WASHER (E)

17 mm

Qty: 4

BOLT (D)

55 mm

Qty: 4

HARDWARE BAG 2 CONTENTS (For Steps A–B):

11

EX-78 ASSEMBLY STEP 2

EX-78

SPRING WASHER (B)

15 mm

Qty: 4

FLAT WASHER (I)

16 mm

Qty: 4

BOLT (H)

35 mm

Qty: 4

NUT (J)

Qty: 4

GUIDE RAILS

MAIN FRAME

BOLTS (H)

SPRING WASHERS (B)

FLAT WASHERS (I)

NUTS (J)

C Attach the guide rails to the main frame

using 4 bolts (h), 4 flat washers (i), 4

spring washers (b) and 4 nuts (j).

HARDWARE BAG 2 CONTENTS (For Step C) :

12

ASSEMBLY STEP 3

ALL

MODELS

EX-78 SHOWN

BOLT (M)

SPRING WASHER (B)

FLAT WASHER (K)

WAVY WASHER (L)

PEDAL ARM

CRANK

PEDAL ARM WHEEL

GUIDE RAIL

CONSOLE MAST

PRE-INSTALLED BOLTS

CONSOLE CABLE

MAIN FRAME

NOTE: Be

careful not

to pinch any

wires while

attaching the

console mast.

A Open hardware bag 3.

B Carefully pull the console cable through

the console mast using the twist tie located

inside the console mast.

C Gently slide the console mast onto the

main frame and attach console mast to

main frame using pre-installed bolts.

D Slide wavy washer (l) over crank

followed by pedal arm as shown. Rest

pedal arm wheel on guide rail.

E Attach the pedal arm to the crank using 1

flat washer (k), 1 spring washer (b)

and 1 bolt (m).

F Repeat steps E–F on the opposite side of the

elliptical.

BOLT (M)

20 mm

Qty: 2

SPRING WASHER (B)

15 mm

Qty: 2

FLAT WASHER (K)

20 mm

Qty: 2

WAVY WASHER (L)

22.5 mm

Qty: 2

HARDWARE BAG 3 CONTENTS :

13

ASSEMBLY STEP 4

A Open hardware bag 4.

B Silde 1 flat washer (n), 1 wavy washer

(l) and another flat washer (n) onto the

console mast.

C Slide lower handlebar onto console

mast and attach using 1 flat washer (n),

1 flat washer (k), 1 handlebar cap, 1

spring washer (b) and 1 bolt (m).

D Repeat steps B–C on the opposite side of the

elliptical.

BOLT (M)

20 mm

Qty: 2

SPRING WASHER (B)

15 mm

Qty: 2

FLAT WASHER (K)

20 mm

Qty: 4

WAVY WASHER (L)

22.5 mm

Qty: 2

FLAT WASHER (N)

25 mm

Qty: 6

HARDWARE BAG 4 CONTENTS :EX-78 SHOWN

BOLT (M)

SPRING

WASHER (B)

FLAT WASHERS (K)

FLAT WASHERS (N)CONSOLE MAST

HANDLEBAR

CAP

LOWER HANDLEBAR

WAVY WASHER (L)

ALL

MODELS

14

BOLT (O)

SPRING WASHER (B)

FLAT WASHER (E)

FLAT WASHER (K)

BOLT (M)

NUT (J)

LOWER HANDLEBAR

SPRING WASHER (B)

TEFLON WASHERS (P)

LOWER LINK ARM

PEDAL ARM BRACKET

ASSEMBLY STEP 5

ALL

MODELS

A Open hardware bag 5.

B Slide lower link arm onto pedal arm

bracket.

C Attach lower link arm to pedal arm

using 1 flat washer (k), 1 spring

washer (b) and 1 bolt (m).

D Align opposite end of lower link arm with

bracket on bottom of lower handlebar.

E Place teflon washers (p) on both sides of

the lower link arm. While holding teflon

washers (p) slide lower link arm into

bottom end of lower handlebar.

F Secure the joint with 1 flat washer (e), 1

spring washer (b),1 bolt (o) and secure

with 1 nut (j).

G Repeat steps B–F on the opposite side of the

elliptical.

BOLT (M)

20 mm

Qty: 2

SPRING WASHER (B)

15 mm

Qty: 4

FLAT WASHER (K)

20 mm

Qty: 2 TEFLON

WASHER (P)

28.4 mm

Qty: 4

FLAT WASHER (E)

17 mm

Qty: 2

NUT (J)

Qty: 2 BOLT (O)

70 mm

Qty: 2

HARDWARE BAG 5 CONTENTS :

EX-78 SHOWN

15

EX-68

EX-78

GS1050E

EX-68, EX-78 ASSEMBLY STEP 6

* This step is for EX-68, EX-78, GS1050E models only.

* CE5.1 and EX-58 models skip to next page.

A Open hardware bag 6.

B Silde top cap and top cap rear cover

over console mast and snap into place.

C Slide console mast boot around

console mast and insert into top cap.

D Slide water bottle holder over

console mast and attach using 3 bolts

(r).

EX-78 only:

E Slide rear cap over rear stabilizer

and attach using 2 screws (q).

BOLT (R)

12 mm

Qty: 3

EX-78 only:

SCREW (Q)

15 mm

Qty: 2

HARDWARE BAG 6 CONTENTS :EX-78 SHOWN

WATER

BOTTLE

HOLDER

CONSOLE MAST

CONSOLE MAST BOOT

TOP CAP

BOLT (R)

SCREWS (Q)

REAR CAP (EX-78 ONLY)

BOLTS (R)

TOP CAP

REAR

COVER

REAR STABILIZER

16

WATER

BOTTLE

HOLDER

CONSOLE MAST

CONSOLE MAST BOOT

SCREW (S)

SCREWS (S)

TOP CAP

CE5.1

EX-58

EX-58, CE5.1 ASSEMBLY STEP 7

* This step is for CE5.1 and EX-58 models only.

* EX-68, EX-78, GS1050E models skip to next page.

A Open hardware bag 7.

B Silde top cap over console mast and

snap into place.

C Insert console mast boot over top cap

and snap into place.

D Slide water bottle holder over

console mast and attach using 3

screws (s).

HARDWARE BAG 7 CONTENTS :

SCREW (S)

12 mm

Qty: 3

17

ALL

MODELS

A Open hardware bag 8.

B Attach the CONSOLE CABLES to the

CONSOLE.

C Carefully tuck the CONSOLE CABLES into

the CONSOLE MAST before attaching the

CONSOLE. Attach CONSOLE to CONSOLE

MAST using 4 BOLTS (T).

D Slide UPPER HANDLEBARS onto LOWER

HANDLEBARS and align NOTCH with TAB

making sure handlebars are joined together

completely. Secure UPPER HANDLEBARS

to LOWER HANDLEBARS using PRE-

ATTACHED SET SCREWS.

E Repeat step D on other side.

YOU ARE FINISHED!

ASSEMBLY STEP 8

BOLT (T)

10 mm

Qty: 4

HARDWARE BAG 8 CONTENTS :CE5.1, EX-58 SHOWN

CONSOLE

CONSOLE MAST

BOLTS (T)

UPPER HANDLEBAR

CONSOLE CABLES

LOWER HANDLEBAR

PRE-INSTALLED

SET SCREWS

NOTCH

TAB

NOTE: Be careful not

to pinch any wires while

attaching the console.

18

19

ELLIPTICAL OPERATION

This section explains how to use your elliptical’s console and programming.

The BASIC OPERATION section in the ELLIPTICAL GUIDE has instructions for the following:

• LOCATION OF THE ELLIPTICAL

• POWER/GROUNDING INSRUCTIONS

• FOOT POSITIONING

• MOVING THE ELLIPTICAL

• LEVELING THE ELLIPTICAL

• POWER/MANUAL INCLINE OPERATION

• USING THE HEART RATE FUNCTION

20

DISTANCE

TIME

SPEED

LEVEL

CALORIES HEART RATE

TA R G E T S

TIME

C A LO R I E S

DISTANCE

W O R KO U T S

ROLLING

INTERVALS

WEIGHT LOSS

1

2

3

4

5

6

7

8

9

10

ENTER

C

A

B

D

H

F

J

E

K

H

G

P

L

I I

M

Q

N N

O

R

EX-58

CE5.1

La page charge ...

Horizon Fitness EX-58 Le manuel du propriétaire

Ce manuel convient également à

Horizon Fitness EX-58 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents