Breckwell AH3024 Manuel utilisateur

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Model AH3024FP

853067B-4805H

Report # F18-149

Please read this manual BEFORE installing and

operating this replace.

CALIFORNIA PROPOSITION 65 WARNING:

This product can expose you to chemicals including carbon monoxide, which

is known to the State of California to cause cancer, birth defects and/or other

reproductive harm. For more information, go to www.P65warnings.ca.gov

Ce produit peut vous exposer à des produits chimiques, y compris le

monoxyde de carbone, qui est connu dans l'État de Californie pour causer

le cancer, des malformations congénitales et / ou d'autres problèmes de

reproduction. Pour plus d'informations, visitez www.P65warnings.ca.gov

109 East 17th Street, Suite 5478 • Cheyenne, WY 82001 •

Phone: (833) 222-3241 • Web: www.acadiahearth.com

- Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

- Installation and service must be performed by a qualied installer, service agency or the gas supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

2

CERTIFICATIONS

This appliance may be installed in an after market permanently located, manufactured home (USA only) or mobile home,

where not prohibited by local codes. It is only for use with the type of gas indicated on the rating plate, and is not convertible

for use with other gassed, unless a certied kit is used.

• After-market: Completion of sale, not for purpose of resale, from the manufacturer.

Laboratory:

PFS-TECO Laboratories

Standards:

• ANSI Z21.88-2017/CSA 2.33-2017, Vented Gas Fireplace Heaters

• CSA 2.17-2017, Gas-Fired Appliances for Use at High Altitudes

• CSA P.4.1-2015, Testing Method for Measuring Annual Fireplace Efciency

This installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1.

852502B





















!

www.ncertied.org

We recommend that our gas

hearth products be installed

and serviced by profes-

sionals who are certied in

the U.S. by the National

Fireplace Institute® (NFI) as

NFI Gas Specialists.

3

TABLE OF CONTENTS

OVERVIEW

Dimensions .....................................................................5

Safety Label ...................................................................6

Requirements For The Commonwealth Of

Massachusetts ...............................................................7

Installation of Carbon Monoxide Detectors .........................7

Approved Carbon Monoxide Detectors ..............................7

Signage ...................................................................................7

Inspection................................................................................7

Exemptions ..............................................................................7

Manufacturer Requirements ..................................................7

Gas Equipment Venting System NOT Provided ...................7

Before You Start ............................................................. 8

Product Features ..........................................................9

Product Specications ...........................................................9

Controls ...................................................................................9

Part Overview ................................................................10

High Elevations .......................................................................10

INSTALLATION

Venting ...........................................................................11

Rear Vent Application ............................................................11

Approved Vent Systems ........................................................13

Venting Requirements ............................................................13

Vent Section Clearances .......................................................13

Use Of Elbows ..........................................................................13

Framing ..........................................................................14

Wall Enclosure Rough Opening ............................................14

Floor Support And Protection ................................................16

Vent Termination Framing ......................................................16

Vertical Terminations ..............................................................16

Horizontal Terminations ..........................................................17

Mounting Bracket Assembly And Installation ......................17

Mantel And Finishing Requirements ............................18

Finishing Recommendations .................................................18

Gas Line Connection .................................................... 19

Gas Conversion (sold separately) ........................................19

Gas Line Installation ...............................................................19

Termination Locations...................................................20

Vertical Vent Cap Termination ..............................................20

Minimum Termination Clearances .......................................21

Top Vent (VERTICAL ONLY) ..........................................22

Restrictor Adjustment .............................................................22

Top Venting....................................................................23

Vertical Terminations ..............................................................23

Combination Venting .............................................................23

Rear Venting .................................................................. 24

Natural Gas Installations ........................................................24

Horizontal Terminations ..........................................................24

Combination Venting .............................................................24

LP Gas Installations .................................................................25

Horizontal Terminations ..........................................................25

Combination Venting .............................................................25

Log and liner Installation ..............................................26

Setup...............................................................................26

Glass Frame Assembly ...........................................................26

Remove Glass Frame Assembly ...........................................26

Install Glass Frame Assembly ................................................27

Safety Barrier INFORMATION ........................................28

Control Board ................................................................28

Electrical Information .................................................... 28

Electrical Specications .........................................................28

Wiring Requirements ..............................................................28

Replacement Parts And Service .................................30

Over Firing Of Burner ..............................................................30

Maintaining Correct Pilot-Flame ...........................................30

How To Access Components ................................................30

Valve Assembly ......................................................................31

HOMEOWNER OPERATION

Installation Checklist .....................................................32

Lighting Checklist ..........................................................32

Operation Information .................................................32

Using Your Remote Control ....................................................32

Synchronizing The Remote Control .......................................32

Remote Control Functions .....................................................33

Icon Details .............................................................................34

Automatic Safety Restart ......................................................34

Turn On Function .....................................................................34

Turn Off Function .....................................................................34

4

TABLE OF CONTENTS

Understanding Your Remote-Control Icons .........................34

IPI And CPI Modes ..................................................................35

Setting To IPI Or CPI Mode .....................................................35

First-Time Lighting Instructions ......................................35

Safety Information ..................................................................35

Frequently Asked Questions .........................................36

Where Can I Find The Model And Serial Numbers? ............36

Operating Instructions ............................................................36

Turning Off ...............................................................................36

What Happens When First Lit? ...............................................37

Additional Curing Information ...............................................37

Can I Operate During Power Outages? ...............................37

What Is The Required Annual Maintenance? ......................37

How Do I Clean The Glass? ...................................................38

Is My Flame Appearance Correct? .....................................38

What Should I Do If Sooting Occurs? ....................................39

How Do I Change From °C to °F On My Remote? ...............39

How Do I Set The Child-Lock Mode? ....................................39

When Should I Change The Batteries In My Remote? .........39

Why Did My Thermostat Disappear From My Remote? .....39

Why Won’t It Turn On? ...........................................................39

Adjustment ..................................................................... 40

Pressure Testing .......................................................................40

Inlet Pressure Test ....................................................................40

Manifold Pressure Test ............................................................40

Burner Flame Adjustments .....................................................41

Gas Flame Adjustment .........................................................41

Troubleshooting .............................................................42

Burner And Pilot System .........................................................44

Fan ...........................................................................................44

Vent System ............................................................................44

Glass Assembly ......................................................................45

5

OVERVIEW

DIMENSIONS

D

C

G

H

L

M

Electrical

Access

N

B

O

A

F

Gas Line

Access

E

K

J

Physical Dimensions

inches mm

A Height 33 839

B Width 35.5 902

C Depth 15.875 403

D Back Width 19 483

E Back To Gas Line Access 6.5 166

F Bottom To Gas Line Access 2.25 58

G Front To Top Vent Center 8.75 222

H Back To Top Vent Center 6.5 166

J Floor To Rear Vent Center 26 661

K Floor To Top Heat Shield Stand Offs 47 1094

L Back To Electrical Access 8 204

M Bottom To Electrical Access 2 51

N Firebox Opening Width 30.5 774

O Firebox Opening Height 23.5 597

6

When initially lit, condensation will appear on the glass. This is normal and will disappear after several minutes. A

paint smell will occur during the rst few hours of burning. It is recommended to leave the fan off during this period

to help speed the paint curing process. It may produce noises of varying degree as it heats and cools due to

metal expansion and contraction. This is normal, and does not affect the performance or longevity. See “Curing

Instructions” section of this manual.

SAFETY LABEL

OVERVIEW

Hot while in operation. Do not touch. Severe burns may result. Keep children, clothing, furniture,

gasoline, and other liquids having flammable vapors away. Keep burner and control compartment

clean. See installation and operating instructions accompanying appliance.

Do not operate the appliance with glass removed, cracked, or broken. Replacement of the

panel(s) should be done by a licensed or quali

fied service person.

CAUTION:

853069B

ON

OFF

ON/OFF

CAUTION:

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing

property damage, personal injury, or loss of life.

A. This appliance is equipped with an ignition device that automatically lights the

pilot. Do not try to light the pilot by hand.

B. BEFORE OPERATING, smell around the appliance area for gas. Be sure to

smell next t

o the floor because some gas is heavier than air and will settle on

the floor.

WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electric switch; do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor's phone. Follow the gas

supplier's instructions.

•

If you cannot reach your gas supplier, call the fire department.

C. Use only your hand to

turn the gas control manual valve. Never use tools. If the

valve will not turn by hand, do not try to repair it; call a qualified service

technician. Force or attempted repair may result in a fire or explosion.

D. Do not use this appliance if any part has been under water. Immediately call a

qualified service technician inspect the appliance and to replace any part of the

control system and any gas cont

rol that has been under water.

OPERATING INSTRUCTIONS

1. STOP! Read the safety information above on this label.

2. Press the wireless remote "OFF" button.

3. Turn off all electric power to the appliance.

4. This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to

light the pilot by hand.

5. Locate the manual valve installed by your qualified service technician. Tu

rn the manual valve

clockwise to the "OFF" position.

6. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell

gas, STOP! Follow "B" in the safety information above on this label. If you do not smell gas, go to

the next step.

7. Turn the manual valve counterclockwise to the "ON" position.

8. Turn on all electric power to the appliance.

9. Press the

wireless remote ON button.

10. If the appliance will not operate, follow the instructions, "To Turn Off Gas To Appliance" and call

your service technician or gas supplier.

TO TURN OFF GAS TO APPLIANCE

1. Press the wireless remote "OFF" button.

2. Turn off all electric power to the appliance if service is to be performed.

3. Locate the manual valve installed by your qualified service technician.

4. Turn the m

anual valve clockwise to the "OFF" position.

This image is only an example. The label on the actual unit will vary slightly.

7

REQUIREMENTS FOR THE COMMONWEALTH OF MASSACHUSETTS

The following requirements reference various Massachusetts

and national codes not contained in this manual. For all

sidewall horizontally vented gas fueled equipment installed

in every dwelling, building or structure used in whole or in part

for residential purposes, including those owned or operated

by the Commonwealth and where the side wall exhaust vent

termination is less than (7) feet above nished grade in the

area of the venting, including but not limited to decks and

porches, the following requirements shall be satised:

Installation of Carbon Monoxide Detectors

At time of installation of side wall horizontally vented gas

fueled equipment, the installing plumber or gas-tter shall

observe that a hard wired carbon monoxide detector with an

alarm and battery back-up is installed on the oor level where

the gas equipment is to be installed. In addition, the installing

plumber or gas-tter shall observe that a battery operated or

hard wired carbon monoxide detector is installed on each

additional level of the dwelling, building or structure served

by the side wall horizontal vented gas fueled equipment. It

shall be the responsibility of the property owner to secure the

services of qualied licensed professionals for the installation

of hard wired carbon monoxide detectors. In the event that

the side wall horizontally vented gas fueled equipment is

installed in a crawl space or attic, the hard wired carbon

monoxide detector with alarm and battery back-up may be

installed on the next adjacent oor level. In the event that the

requirements of this subdivision can not be met at the time

of completion of installation, the owner shall have a period

of thirty (30) days to comply with the above requirements;

provided, however, that during said thirty (30) day period, a

battery operated carbon monoxide detector with an alarm

shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance

with the above provisions shall comply with NFPA 720 and be

ANSI/UL 2034 listed and IAS certied.

Signage

A metal or plastic identication plate shall be permanently

mounted to the exterior of the building at a minimum of eight

(8) feet above grade directly in line with the exhaust vent

terminal for the horizontally vented gas fueled heating the

appliance or equipment. The sign shall read, in print no less

the one-half inch (½) in size, “GAS VENT DIRECTLY BELOW.

KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally

vented gas fueled equipment shall not approve the

installation unless, upon inspection, the inspector observes

carbon monoxide detectors and signage installed in

accordance with the provisions of 248 CMR 5.08 (2) (a) 1

through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08 (2)

(a) 1 through 4: The equipment listed in Chapter 10 entitled

“Equipment Not Required To Be Vented” in the most current

edition of NFPA 54 as adopted by the Board; and Product

Approved side wall horizontally vented gas fueled equipment

installed in a room or structure separate from the dwelling,

building or structure used in whole or in part for residential

purposes.

Manufacturer Requirements

Gas Equipment Venting System Provided: When the

manufacturer of Product Approved side wall horizontally

vented gas equipment provides a venting system design

or venting system components with the equipment, the

instructions provided by the manufacturer for installation of

the equipment and the venting system shall include:

• Detailed instructions for the installation of the venting

system design or the venting system components; and

• A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of Product Approved side wall

horizontally vented gas equipment does not provide the

parts for venting the ue gases, but identies “special venting

systems”, the following requirements shall be satised by the

manufacturer:

• The referenced “special venting systems” instructions shall

be included with the appliance or equipment installation

instructions and;

• The “special venting systems” shall be Product Approved

by the Board, and the instructions for that system shall

include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved

side wall horizontally vented gas fueled equipment, all venting

instructions, all parts lists for venting instructions, and/or all

venting design instructions shall remain with the appliance or

equipment at the completion of the installation.

OVERVIEW

8

This is a vented product. It must be properly installed by a qualied service person. The glass door must be properly seated

and sealed. If this appliance is not properly installed by a qualied service person with glass door properly seated and sealed,

combustion leakage can occur. CARBON MONOXIDE POISONING: Early signs of carbon monoxide poisoning are similar to the

u with headaches, dizziness and/or nausea. If you have these signs, it may not have been installed properly. Get fresh air at

once! Have it inspected and serviced by a qualied service person. Some people are more affected by carbon monoxide than

others. These include pregnant women, people with heart or lung disease or anemia, those under the inuence of alcohol, and

those at high altitudes. Propane/LP gas and natural gas are both odorless. An odor-making agent is added to each of these

gases. The odor helps you detect a gas leak. However, the odor added to these gases can fade. Gas may be present even

though no odor exists. Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to

safe and proper operation.

1. Installation and repair should be done by a qualied

service person. The appliance should be inspected before

use and at least annually by a professional service person.

More frequent cleaning may be required due to excessive

lint from carpeting, bedding material, etc. It is imperative

that control compartments, burners, and circulating air

passageways of the appliance be kept clean.

2. Only use the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases unless

a certied kit is used.

3. Do not place propane/LP supply tank(s) inside any

structure. Locate propane/LP supply tank(s) outdoors. To

prevent performance problems, do not use propane/LP

fuel tank of less than 100 lbs. capacity.

4. If you smell gas:

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

5. Never install:

• In a recreational vehicle

• Where curtains, furniture, clothing, or other ammable

objects are less than 36” from the front, top, or sides of it

• In high trafc areas

• In windy or drafty areas

6. This appliance reaches high temperatures. Children and

adults should be alerted to the hazards of high surface

temperature and should stay away to avoid burns or

clothing ignition. It will remain hot for a time after shutdown.

Allow surfaces to cool before touching.

7. Young children should be carefully supervised when they

are in the same room as the appliance. Toddlers, young

children and others may be susceptible to accidental

contact burns. A physical barrier is recommended if there

are at-risk individuals in the house. To restrict access to a

replace or stove, install an adjustable safety gate to keep

toddlers, young children and other at-risk individuals out

of the room and away from hot surfaces.

8. Due to high temperatures, the appliance should be

located out of trafc and away from furniture and

draperies. Clothing or other ammable material should

not be placed on or near the appliance.

9. When the appliance is installed directly on carpeting, tile

or other combustible material other than wood ooring,

you must use a metal or wood panel or hearth pad

extending the full width and depth of the appliance.

10. Do not modify the appliance under any circumstances.

Any parts removed for servicing must be replaced prior to

operating.

11. Turn off and let cool before servicing, installing, or repairing.

Only a qualied service person should install, service, or

repair it. Have burner system inspected annually by a

qualied service person.

12. You must keep control compartments, burners, and

circulating air passages clean. More frequent cleaning

may be needed due to excessive lint and dust. Turn off

the gas valve and pilot light before cleaning.

13. Have venting system inspected annually by a qualied

service person. If needed, have venting system cleaned

or repaired.

14. Keep the surrounding area clear of combustible materials,

gasoline, and other ammable vapor and liquids. Do not

run the appliance where these are used or stored. Do not

place items such as clothing or decorations on or around

the appliance.

15. Do not use to cook food or burn paper or other objects.

16. Never place anything on top of the appliance.

17. Do not use any solid fuels (wood, coal, paper, cardboard,

etc.) in this appliance. Use only the gas type indicated on

rating plate.

BEFORE YOU START

OVERVIEW

Read this owner’s manual carefully and completely before trying to assemble, operate, or service. Any change to this

appliance or its controls can be dangerous. Improper installation or use can cause serious injury or death from re, burns,

explosions, electrical shock and carbon monoxide poisoning.

9

OVERVIEW

18. This appliance, when installed, must be electrically

grounded in accordance with local codes or in the

absence of local codes, with the National Electrical

Code, ANSI/NFPA 70, or the Canadian Electrical Code,

CSA C22.1.

19. Do not obstruct the ow of combustion and ventilation

air in any way. Provide adequate clearances around

air openings into the combustion chamber along with

adequate accessibility clearance for servicing and proper

operation.

20. Do not use if any part has been under water. Immediately

call a qualied service technician to inspect and if

needed replace any part of the control system and any

gas control which as been under water.

21. Do not operate if any log is broken.

22. Do not use a blower insert, heat exchanger insert, or any

other accessory not approved for use with this appliance.

23. Do not operate with the glass front removed, cracked, or

broken. Replacement of the glass should be done by a

licensed qualied service person.

PLEASE READ THE FOLLOWING CAREFULLY It is not unusual to have some odor during the rst burn. This is

due to the manufacturing process. Please ensure that your room is well ventilated during burn off — open

all windows. It is recommended that you burn your appliance for at least ten (10) hours the rst time you

use it. Place the fan switch in the “OFF” position during this time.

Never connect this appliance to private (non-utility) gas wells. This gas is commonly known as wellhead gas.

Product Specications

This appliance:

• has been certied for use with either natural or propane gas. See appropriate data plates.

• is not for use with solid fuels.

• is approved for bedroom or bed sitting room installations.

• must be installed in accordance with local codes if any. If none exist use the current installation code. ANSI Z223.1/NFPA

54 in the USA, CSA B149.1 in Canada.

• is mobile home approved.

• must be properly connected to a venting system.

• is not approved for closet installations.

• is approved to be vented using DuraVent, BDM, and Olympia components.

The classication “noncombustible material” includes, but is not limited to stone, brick and mortar. Noncombustibles are

safe to overlay the black-painted metal face (including radiant plates) and do not pose a re hazard. Do not allow any

noncombustible nish material to extend past or interfere with opening.

The classication “combustible material” includes, but is not limited to plywood, drywall and particle board. Combustible

materials may contact the sides, bottom or back of rebox. Do not overlay the black painted face with combustible materials.

Controls

PRODUCT FEATURES

Valve RegulatorMaster On/Off Switch Air Shutter Adjustment

IMPORTANT

10

Gas Pressures

Natural Propane (LP)

Inlet Minimum 5.0" w.c. 12.0" w.c.

Inlet Maximum 10.5" w.c. 14.0" w.c.

Manifold Pressure 3.8" w.c. 11.0" w.c.

Gas Specications & Orice Size

Fuel

Max. Input

BTU/h

Min. Input

BTU/h

Orice

Size

Nat. 27,000 14,000 #40

LP 27,000 13,000 #53

High Elevations

Input ratings are shown in BTU per hour and are certied without derating for elevations up to 4,500 feet (1,370 m) above sea

level.

For elevations above 2,000 feet (50.8 m) in USA, installations must be in accordance with the current ANSI Z223.1/NFPA 54 and/

or local codes having jurisdiction.

In Canada, please consult provincial and/or local authorities having jurisdiction for installations at elevations above 4,500 feet

(1,370 m). Natural Gas and Propane Installation Code, CSA B149.1

OVERVIEW

If you live in a cold climate, seal all cracks around your appliance, and wherever cold air could enter the room,

with noncombustible material. It is especially important to insulate the outside chase cavity between the studs and

under the oor on which the appliance rests, if the oor is above ground level.

Failure to follow these instructions will void the warranty.

This appliance must be vented to the outside. The venting system must NEVER be attached to a chimney serving a separate

solid fuel burning appliance. Each gas appliance must use a separate vent system. Do not use common vent systems.

Read all instructions completely and thoroughly before attempting installation. Failure to do so could result in serious injury,

property damage or loss of life. Operation of improperly installed and maintained venting system could result in serious

injury, property damage or loss of life.

Do not pack the open air spaces with insulation or other materials. This could cause high temperatures and may present

a re hazard and serious injury, property damage or loss of life. Operation of improperly installed and maintained venting

system could result in serious injury, property damage or loss of life.

PART OVERVIEW

Read this homeowner manual thoroughly and follow all instructions carefully. Inspect all contents for shipping damage and

immediately inform your authorized dealer if any damage is found. Do not install any damaged, incomplete, or substitute

parts. Check your packing list to verify that all listed parts have been received.

AA BATTERIES

(4 PACK)

Natural Gas LP Gas

REMOTE

9V BATTERY

BOX

AAA BATTERIES

(3 PACK)

11

INSTALLATION

STEP 1

Remove the ve (5) #10AX1/2 HX screws attaching the back

cover plate to the rear of the appliance.

STEP 2

Remove the four (4) #10AX1/2 HX screws attaching the intake

chamber cover plate to the intake chamber.

STEP 3

Remove the six (6) #10AX1/2 HX screws attaching the rebox

exhaust cover to the rebox.

STEP 4

Remove the ve (5) #10AX1/2 HX screws attaching the cover

plate to the top of the appliance.

STEP 5

Remove the four (4) #10AX1/2 HX screws attaching the draft

hood collar to the intake chamber.

STEP 6

Remove the six (6) machine screws attaching the intake inner

draft hood to the rebox inside top.

VENTING

Rear Vent Application

There are outlets for both top and rear venting. The unused vent exit must have the cover plates in place,

and the cover plates must be removed from the exit according to the instructions below to be used.

All components removed from the top vent exit will be reinstalled for the rear vent.

When removing and retting the plates be sure the associated gaskets are undamaged and retted as required.

IMPORTANT

12

STEP 7

Attach the rebox exhaust cover to the rebox inside top

using the previously removed six (6) #10AX1/2 HX screws.

STEP 8

Attach the intake chamber cover plate to the intake

chamber using the previously removed four (4) #10A X 1/2

HX screws.

STEP 9

Attach the back cover plate to the top of the appliance

using the previously removed ve (5) #10A X 1/2 HX screws.

STEP 10

Attach the intake inner draft hood to the rebox back using

the previously removed six (6) #10A X 1/2 HX screws.

STEP 11

Attach the draft hood collar to the intake chamber using the

previously removed four (4) #10AX1/2 HX screws.

STEP 12

Attach the cover plate to the outer back of the appliance

using the previously removed ve (5) #10AX1/2 HX screws.

INSTALLATION

13

Approved Vent Systems

DuraVent (DirectVent Pro)

46DVA-VC – Low Prole Cap Vertical

46 DVA-VCH – Hi Wind Cap Vertical

46 DVA-HC – Square High Wind Cap Horizontal

Olympia Chimney (Ventis)

VDV-VCH04 – Round High Wind Cap Vertical

VDV-VCH4 – Round Cap Vertical

VDV-HC04 – Square High Wind Cap Horizontal

BDM (Pro-Form)

DVR6-VCH Round High Wind Cap Vertical

DVR6-HC Square Cap Horizontal

DVR-HCP HCA Pyramid Termination Cap Horizontal

Venting Requirements

Consult the local and national installation codes to assure adequate combustion and ventilation air is available. Venting

requirements apply to both natural gas and LP gas.

• Flame height and appearance will vary depending upon venting conguration and the type of fuel used.

• Refer to the vent manufacturer’s installation manual for complete installation instructions. Vent installation must conform

with venting requirements and restrictions as outlined in this manual.

• Provide a means for visually checking the vent connection to the appliance after it is installed.

Vent Section Clearances

Wall thimble products that comply with the required 1 in (25 mm) clearance to combustibles must be installed for

all horizontal vent runs that pass through interior or exterior walls. These wall thimble products may be insulated

using unfaced insulation products listed as noncombustible per ASTM E 136.

Attic insulation shields may be insulated using unfaced insulation products listed as noncombustible per ASTM E 136.

Vertical Pipe Section Clearances

Surface Sides

All Approved Venting 1 in (25 mm)

Horizontal Pipe Section Clearances

Surface Top Bottom Sides

All Approved Venting 3 in (76 mm) 1 in (25 mm) 1 in (25 mm)

Use Of Elbows

• MAXIMUM NUMBER OF 90° ELBOWS: 4

• For each additional 90° elbow used after the rst 90° elbow, 3 ft (91.4 cm) must be subtracted from maximum venting

allowed.

• For each 45° elbow used, 1½ ft (457 mm) must be subtracted from maximum venting allowed.

• (2) 45° degree elbows may be used in place of (1) 90° elbow.

INSTALLATION

14

FRAMING

Attach the two stand-off assembles to the top of the unit using four

10-32 X 1/2 screws as shown.

INSTALLATION

The top stand-offs provide the minimum clearance to the header. Use only non-combustible material in this area for the entire

width of the appliance. DO NOT use wood, sheet-rock, etcetera, in this zone. Top stand-off brackets must be formed and

attached prior to positioning into framed opening.

The two stand offs are located in the rebox. The four 10-

32 X 1/2 screws are provided in the parts bag.

Wall Enclosure Rough Opening

• Framing dimensions should allow for wall

covering thickness and replace facing

materials. If using a hearth, adjust the rough

opening size as necessary to maintain

minimum clearance requirements.

• If masonry is to be used (optional), prepare

the necessary foundation for the masonry

load. When masonry construction is to be

used, a lintel must be used over the top

of the replace to support the additional

weight.

Provide adequate clearances around air openings into the combustion chamber. Provide adequate clearance in front of

the appliance for barrier removal, component access, gas line installation, service access, etc.

15-7/8”

(403 mm)

47-1/4” (1201 mm)

36-1/4”

(920 mm)

15

Approved vent system elbows vary in vertical length. Consult vent manufacturer’s instructions to determine the

elbow dimension used for your installation. Adjust as necessary to maintain the required 1” (25mm) clearance from

the vent pipe to combustible material.

INSTALLATION

TYPICAL HORIZONTAL INSTALLATION

TOP VENT

36¼”

(920mm)

1”

(25mm)

15

”

(403mm)*

TYPICAL HORIZONTAL INSTALLATION

REAR VENT

1”

(25mm)

36

¼”

(920mm)

15

”

(403mm)*

TYPICAL VERTICAL INSTALLATION

TOP VENT

”

1”

(25mm)

36

¼”

(920mm)

15

(403mm)*

TYPICAL CORNER INSTALLATION

TOP VENT

50

”

(1280mm)

36

¼”

(920mm)

11

”

(301mm)

¼”

(6mm)

24

”

(628mm)

35

”

(905mm)

TYPICAL VERTICAL INSTALLATION

REAR VENT

26

½”

(673mm)**

1”

(25mm)

36

¼”

(920mm)

Minimum Clearances to Combustible Material

From Appliance To inches mm

Top Stand-Offs 0 0

Left And Right Side Stand-Offs 0 0

Back Stand-Offs 0 0

Corners 1/4 6

Front 36 915

Top To Ceiling 51 1295

Sides To Adjacent Sidewall 6 153

Mantel 9 in (229 mm) deep, 10” (254 mm) from appliance top

**DIMENSION SHOWN WITH LISTED DURAVENT ELBOW.

**UNITS SHOWN WITHOUT HEAT SHIELD FOR CLARITY.

Apply a generous amount of high temperature sealant to the around

the ue outlet.

IMPORTANT

16

Floor Support And Protection

• If installed directly on carpeting, tile, or other combustible material other than wood ooring, this appliance shall be

installed on a metal or wood panel extending the full width and depth of the appliance.

• If installed above oor level, a solid, continuous platform must be constructed below the appliance.

• Consider the height of hearth nish material (stone, brick, etc.) when building a platform. The bottom of the appliance

must be level with nished hearth to allow for a proper t of the safety barriers.

• Build the hearth to desired size and height. If a hearth extension is desired, combustible material may be used.

Vent Termination Framing

15-7/8”

(403mm)

39”

(991mm)

Top Vent Minimum

Horizontal Venting

INSTALLATION

FIRE HAZARD: Do NOT install directly on carpeting, vinyl, or any other combustible material other than wood.

DO NOT RECESS THE VENT CAP INTO WALL OR SIDING.

Vertical Terminations

• Follow vent pipe manufacturer’s installation instructions for vertical terminations.

• A minimum of 1 in (25 mm) clearance on all sides of the vertical vent pipe must be maintained.

• Attic insulation shields may be insulated using unfaced insulation products listed as non-combustible per ASTM E 136.

Cold air transfer area. The surround appliance chase must comply with all clearances as

outlined in this manual, and be constructed in compliance with local building codes. Outside

walls should be insulated to prevent cold air from entering room.

Vent cap location must be in compliance with the minimum termination clearance information listed in

this manual.

IMPORTANT

17

Horizontal vent sections require 1/4 in (6 mm) rise for every 12 in (305 mm) of travel.

1. Measure from oor level of the appliance to the center of where the vent pipe will penetrate the wall. Elbows listed with

approved vent systems will vary in vertical length. Please consult the vent manufacturer’s instructions to determine the

elbow dimension used for installation. Adjust the wall pass-through rough opening dimensions as necessary to maintain

clearance requirements.

2. Cut and frame an opening in the wall to allow the vent system to run level through the wall pass-through.

3. Follow the vent pipe manufacturer’s installation instructions for vent installation.

15-7/8”

(403mm)

25.7”

(653mm)

Rear Vent Minimum

Horizontal Venting

INSTALLATION

Mounting Bracket Assembly And Installation

Never permanently remove these assemblies — they must be secured regardless of nish

material used.

1. Bend mounting brackets up 90° at perforation as shown.

Horizontal Terminations

IMPORTANT

Bend Here 90°

18

INSTALLATION

10”

(254 mm)

14”

(356 mm)

9”

(229 mm)

½” (13mm)

NON-COMBUSTIBLE

MATERIAL ONLY

SINGLE VERTICAL

HEADER

MANTEL

47”

(1194 mm)

MANTEL AND FINISHING REQUIREMENTS

Finishing Recommendations

The surface area above the appliance may be

affected by emitted high temperatures. To help avoid

or reduce the possibility of the sheetrock to crack the

following methods are recommended:

• Ensure the non-combustible material and sheetrock

is dry and dust free.

• For taping and mudding seams, we recommend

heat resilient tape, mesh and joint compounds.

Mud must be cured as per manufacturer’s

recommendations.

• For a painted surface, use a high quality acrylic

latex primer and nish coat. Avoid at or light-

colored paints to prevent discoloring.

2. Depending on facing material, the lower half of the mounting bracket can be adjusted forward or backward ½ in (13 mm)

as needed.

3. Attach two (2) mounting brackets to each side of the unit.

Framing Studs

Nailing Flange

Stand-Off Flange

1/2” (13mm)

Clearance

Option 1 Option 2

19

INSTALLATION

GAS LINE CONNECTION

The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any

pressure testing of that system at pressures in excess of ½ psi (3.5 kPa). For test pressures equal to or less than ½ psi

(3.5 kPa), the appliance must be isolated from the gas supply piping system by closing its individual manual shut-off

valve.

The conversion shall be carried out in accordance with the requirements of the provincial authorities

having jurisdiction and in accordance with the requirements of the ANSI Z223.1 installation code.

Gas Conversion (sold separately)

This appliance is manufactured for use with natural gas. Follow the instructions included with the conversion kit if converting

to LP gas. The conversion kit shall be installed by a qualied service agency.

Gas Line Installation

A listed (and Commonwealth of Massachusetts approved) ½ in. (13 mm) tee handle manual shut-off valve and exible gas

connector are to be connected to the ½ in. (13 mm) control valve inlet. If substituting for these components, please consult

local codes for compliance.

• This appliance is equipped with a ⅜” (10 mm) x 18” (457 mm) long exible gas connector and manual shut-off valve.

• Run gas line into appliance. The gas line should be run to the point of connection where the shut-off valve and exible

gas line will connect.

• Do not run gas line in a manner that would obstruct fan operation.

• For high altitude installations, consult the local gas distributor or the authority having jurisdiction for proper rating methods.

Inlet Gas Supply Pressures

Fuel Minimum Pressure Maximum Pressure

Natural Gas 5” WC (1.25 kPa) 10.5” WC (2.62 kPa)

LP Gas 12” WC (2.674 kPa) 14” WC (3.49 kPa)

Installation of the gas line must only be done by a qualied person in accordance with local

building codes, if any. If not, follow ANSI 223.1. Commonwealth of Massachusetts installations

must be done by a licensed plumber or gas tter.

IMPORTANT

20

INSTALLATION

12

x

H

LOWEST

DISCHARGE

OPENING

APPROVED CAP

APPROVED

VENT PIPE

ROOF PITCH = x/12

H - MINIMUM HEIGHT FROM ROOF TO

LOWEST DISCHARGE OPENING

MINIMUM

12” (.30m)

Vertical Vent Cap Clearance

Minimum Height (H) From Roof

Roof Pitch Feet Meters

Flat to 6/12 1.0 0.30

Over 6/12 to 7/12 1.25 0.38

Over 7/12 to 8/12 1.5 0.46

Over 8/12 to 9/12 2.0 0.61

Over 9/12 to 10/12 2.5 0.76

Over 10/12 to 11/12 3.25 0.99

Over 11/12 to 12/12 4.0 1.22

Over 12/12 to 14/12 5.0 1.52

Over 14/12 to 16/12 6.0 1.83

Over 16/12 to 18/12 7.0 2.13

Over 18/12 to 20/12 7.5 2.27

Over 20/12 to 21/12 8.0 2.44

TERMINATION LOCATIONS

Vertical Vent Cap Termination

This appliance must not share or be connected to a chimney ue serving a separate solid-fuel burning appliance.

La page est en cours de chargement...

Breckwell AH3024 Manuel utilisateur

Ce manuel convient également à

Breckwell AH3024 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents