Kenmore Elite 79573133410 Le manuel du propriétaire

Use & Care Guide

Guide d'Utiisation et d'Entretien

English / Fran_;ais

Models/Mocl_les: 795.7313 _

Kenmore Elite°

®

MFL67227105

Sears Brands Management CorporaHon

Hoffman Estates, IL 60179 U.S.A.

www. kenl_ore.com

www.sear s.¢ot_

Sears Canada inc.

Toron_'o, Ontarlo, Canada M5B 2C3

www.sears.¢a

®

Warranty .............................................................................3

Protection Agreements ..............................................4

Important Safety instructions ...........................5-7

Electrical 8, Grounding Requirements ..............7

Parts and Features .......................................................8

Refrigerator Installation .............................. 9-16

Unpacking Your Refrigerator .......................... 9

Installation ....................................................................10

Removing/Replacing Your Refrigerator and

Freezer Handles and Doors ...........................11-15

Leveling and Door Alignment ...................... 16

Using Your Refrigerator ............................ 17-27

Setting the ControJs .................................. 17-18

In=Door ice Bin ...........................................................19

Automatic Jcemaker ................................ 20-21

Food Storage Guide .................................... 22

Refrigerator Section

Water Dispenser ........................................... 23

Refrigerator Shelves ...............................................24

Humidity ControJled Crisper ........................ 25

Temperature Controlled Pantry Drawer ....... 25

Door Bin ............................................................ 26

Dairy Bin ........................................................... 26

Air Filter ............................................................ 26

Freezer Section

Extra Ice Bin ................................................. 27

Durabase ....................................................... 27

Durabase Divider .......................................... 27

Pullout Drawer ............................................... 28

Water Filter ............................................... 29-32

Care And Cleaning ................................... 33-34

General Cleaning Tips ................................ 33

Outside ........................................................... 33

inside Wails ................................................... 33

Door Liner And Gaskets ............................... 33

Plastic Parts.................................................... 33

Condenser Coils ............................................. 33

Light Bulb Replacement ............................... 34

Power interruptions ....................................... 34

When You Go On Vacation ........................ 34

When You Move ............................................ 34

Connecting the Water Line ...................... 35-37

Troubleshooting Guide ............................. 38-44

Kenmore Connect TM System .......................... 45

Service ............................................... Back Cover

®

REFRIGERATOR WARRANTY

f

Kenmore Elite Limited Warranty

WITH PROOF OF SALE, the following warranty coverage applies when this appliance is correctly installed, operated

and maintained according to aii supplied instructions. To arrange for warranty service, call: 1-800-4-MY-HOME®

(1-800-469-4663)

FOR ONE YEAR from the date of sale this appliance is warranted against defects in material or workmanship. A

defective appliance wiii receive free repair or replacement at option of seller. This warranty coverage applies for only

90 days from the sale date in the United States, and is void in Canada, if the appliance is ever used for other than

private household purposes.

FOR FIVE YEARS from the date of sale, the sealed refrigerant system of this appliance is warranted against defects

in material or workmanship. New system components will be supplied for defective ones free of charge. You are

responsible for the labor cost of component installation after the first year from the sale date. This warranty coverage

applies for only one year from the sale date in the United States, and is void in Canada, if the appliance is ever used

for other than private household purposes.

FOR TEN YEARS from the date of sale, the linear compressor of this appliance is warranted against defects in

material or workmanship. A new linear compressor will be supplied free of charge. You are responsible for the labor

cost of installation after the first year from the date of purchase. This warranty coverage applies for only two years

from the sale date in the United States, and is void in Canada, if the appliance is ever used for other than private

household purposes.

This warranty covers ONLY defects in material and workmanship, and will NOT pay for:

1. Expendable items that can wear out from normal use, including but not limited to filters, belts, screw=in base light

bulbs and bags.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions

supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies

Customer's sole and exclusive remedy under this limited warranty shall be product repair or replacement as provided

herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one

year or the shortest period allowed by Jaw. Seller shall not be liable for incidental or consequential damages. Some

states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation on the

duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States or Canada%

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

In-home repair service is not available in all Canadian geographical areas, nor wiii this warranty cover user or servicer

travel and transportation expenses if this product is located in a remote area (as defined by Sears Canada Inc.) where

an authorized servicer is not available.

Sears Brands Management Corporation, Hoffman Estates, IL 60179

Sears Canada Inc., Toronto, Ontario, Canada MSB 2C3

Master Protection Agreements

Congratulations on making a smart purchase. Your new

Kenmore Elite® product is designed and manufactured •

for years of dependable operation. But like all products,

it may require preventive maintenance or repair from

time to time. That's when having a Master Protection

Agreement can save you money and aggravation. •

The Master Protection Agreement also helps extend

the life of your new product. Here's what the

Agreement s includes:

Parts and labor needed to help keep products

operating properly under normal use, not just defects.

Our coverage goes well beyond the product warranty.

No deductibles, no functional failure excluded from

coverage-- real protection.

* Expert service by a force of more than 10,000

authorized Sears service technicians, which means

someone you can trust will be working on your product.

* Unlimited service calls and nationwide service, as

often as you want us, whenever you want us.

* "No-lemon" guarantee - replacement of your covered

product if four or more product failures occur within

twelve months.

Power surge protection against electrical damage due

to power fluctuations.

$250 Food Loss Protection annually for any food

spoilage that is the result of mechanical failure of any

covered refrigerator or freezer.

Rental reimbursement if repair of your covered

product takes longer than promised.

25°/0 discount off the regular price of any non-covered

repair service and related installed parts.

Once you purchase the Agreement, a simple phone calt

is all that it takes to schedute service. You can catl at

any time day or night, or schedule a service appointment

online.

The Master Protection Agreement is a risk free purchase.

If you cancel for any reason during the product warranty

period, we will provide a full refund or a prorated refund

anytime after the product warranty period expires.

Purchase your Master Protection Agreement today!

Some limitations and exclusions apply.

For prices and additional information in the

U.S.A. call 1-800-827-6655.

* Product replacement if your covered product can't be

fixed.

Coverage in Canada varies on some items. For full

detalls call Sears Canada at I=800=361=6665.

Annual Preventive Maintenance Check at your request

- no extra charge.

Fast help by phone - we call it Rapid Resolution

- phone support from a Sears representative on all

products. Think of us as a "talking owner's manual."

Sears Installation Service

For Sears professional installation of home appliances,

garage door openers, water heaters, and other major

home items, in the U.S.A. or Canada call

1-800-4-MY-HOME ®.

In the space below, record the date of purchase, model and serial number of your product. You will find the model and

serial number printed on an identification label located on the interior liner of the refrigerator compartment. Have these

items of information available whenever you contact Sears concerning your product.

Model No.

Serial No.

Date of Purchase

Save these instructions and attach your sales receipt for future reference.

4

BASIC SAFETY PRECAUTIONS

This guide contains many important safety messages. Always read and obey all safety messages.

This is the safety alert symbol, it alerts you to safety messages that inform you of hazards that can kill

or hurt you or others, or cause damage to the product.

All safety messages will be preceded by the safety alert symbol and the hazard

signal word DANGER, WARNING or CAUTION. These words mean:

You will be killed or seriously injured if you do not follow instructions.

You can be killed or seriously injured if you do not follow instructions.

indicates an imminently hazardous situation which, if not avoided,

may result in minor or moderate injury, or product damage.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen

if the instructions are not followed.

To reduce the risk of fire, electrlc shock, or personal

injury when using your product, basic safety precautions

should be followed, includlncj the followincj.

Read all instructions before using this appllance.

* NEVER unplug your refrigerator by pulling on the

power cord. Always grip the plug firmly and putt it

straight out from the outlet.

immediately repair or replace att power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either the plug or connector end.

* Do not modify or extend the power cord length, it

could cause electric shock or fire.

* When moving your refrigerator away from the wall, be

careful not to rotl over or damage the power cord.

* DO NOT store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

DO NOT allow children to climb, stand, or hang on the

refrigerator doors or shetves in the refrigerator. They

could damage the refrigerator and seriously injure

themselves.

* Keep fingers out of pinch point areas; clearances

between the doors and cabinets are necessarily small.

Be careful closing doors when children are in the area.

* Unplug your refrigerator before cleaning or making

any repairs.

NOTE: It is strongly recommended that any service be

performed by a qualified technician.

SAVE THESEiNSTRUCTiONS

5

Before replacing a burned-out or broken light bulb,

unplug the refrigerator or turn off power at the circuit

breaker or fuse box in order to avoid contact with a live .

wire filament. (A burned-out light bulb may break when

being replaced exposing the wire filament.)

NOTE: Some models have LED interior lighting and

service should be performed by a qualified technician.

_, WARNING: Setting either or both controls to the OFF

position does not remove power to the light circuit.

When you are finished, reconnect the refrigerator to

the electrical source and reset the controls (Thermostat,

Refrigerator Control, and or Freezer Control, depending

on the model) to the desired setting.

This refrigerator must be properly installed in

accordance with the Attention Installer Instructions that

were taped to the front of the refrigerator.

After your refrigerator is in operation, do not touch the

cold surfaces in the freezer compartment when hands

are damp or wet. Skin may adhere to the extremely cold

surfaces.

DO NOT touch the automatic ice making mechanism

while the refrigerator is plugged in.

DO NOT refreeze frozen foods which have thawed

completely. The United States Department of

Agriculture in Home and Garden Bulletin No. 69 says:

...You may safely refreeze frozen foods that have

thawed if they still contain ice crystals or if they are

still cold--below 4°C.

...Thawed ground meats, poultry or fish that have any

off-odor or off-color should not be refrozen and should

not be eaten. Thawed ice cream should be discarded.

If the odor or color of any food is poor or questionable,

dispose of it. The food may be dangerous to eat.

Even partial thawing and refreezing reduces the

eating quality of foods, particularly fruits, vegetables

and prepared foods. The eating quality of red meats

is affected less than that of many other foods. Use

refrozen foods as soon as possible to save as much of

their quality as you can.

_, WARNING: This product contains chemicals known to

the State of California to cause cancer and birth defects

or other reproductive harm. Wash handsafter handling.

SAVE THESEINSTRUCTIONS

Junked or abandoned refrigerators are dangerous, even

if they are sitting for only a few days. If you are getting

rid of your old refrigerator, please follow the instructions

at right to help prevent accidents (child entrapment and

suffocation).

BEFORE YOU THROW AWAY

YOUR OLD REFRIGERATOR

OR FREEZER:

• Take off the doors.

• Leave the shelves in place so that

children may not easily climb inside.

6

Your old refrigerator may have a cooling system

that used CFCs or HCFCs (chlorofluorocarbons or

hydrochtorofluorocarbons). CFCs and HCFCs are

believed to harm stratospheric ozone if released to the

atmosphere. Other refrigerants may also cause harm to

the environment if released to the atmosphere.

if you are throwing away your old refrigerator, make

sure the refrigerant is removed for proper disposal

by a qualified technician. If you intentionally release

refrigerant, you may be subject to fines and imprisonment

under provisions of environmental legislation.

iMPORTANT: Please read carefully.

TO CONNECT ELECTRICITY

Electrical Shock Hazard

FOR PERSONAL SAFETY, this appliance must be

properly grounded, Have the wall outlet and the circuit

checked by a qualified electrician to make sure the

outlet is properly grounded,

3-prong

groundingtype I

wall receptacle

3-prong _ I _

grounding I'q---Ft_----_I _/_'_

fW

Ensure proper

_]_ ground exists

/// before use.

USE OF EXTENSION CORDS

Because of pofenflal safety hazards under certain

conditions, the use of an extension cord is nat

recommended. However, if you still elect to use an

extension cord, it is absolutely necessary that it be a UL-

listed (USA), 3-wire grounding type appliance extension

cord having a grounding type plug and outlet, and that

the electricai rating of the cord be 15 amperes (minimum)

and 120 volts.

Use of an extension cord will increase the clearance

needed for the back of the refrigerator.

RECOMMENDED GROUNDING METHOD

The refrigerator should always be plugged into its own

individual properly grounded electrical outlet rated for

115 Volts, 60 Hz, AC only, and fused at 15 or 20 amperes.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a fire

hazard from overheated wires. It is recommended that a

separate circuit serving only this appliance be provided.

Use a receptacle that cannot be turned off with a switch

or putt chain. Do not use an extension cord.

Where a standard two-prong walt outlet is encountered,

it is your personal responsibility and obligation to have

it replaced with a properly grounded three-prong wall

outlet.

7

Use this page to become more familiar with the parts and features of your refrigerator.

NOTE: This guide covers several different models. The refrigerator you have purchased may have some or all of the items

listed below. The locations of the features shown below may not match your model.

O Refrigerator Light

Water Filter (Inside}

Adjustable Door Bins

Fixed Door Bins

Refrigerator Shelves

O Ice Compartment

(Icemaker and Ice Bin)

Humidity Controlled Crisper

Temperature Controlled

Pantry Drawer

Extra Ice Bin

Pullout Drawer

Durabase

Durabase Divider

_) Dairy Bin

Water Tank Cover

Articulating Mullion

Air Filter

Kenmore Connect TM

Speaker

8

Excessive Weight Hazard:

Use two or more people to move and install the

refrigerator. Failure to do so can result in back or

other injury.

UNPACKING YOUR REFRIGERATOR

Excessive Weight Hazard:

Your refrigerator is heavy. When moving the

refrigerator for cleaning or service, be sure to protect

the floor. Always pull the refrigerator straight out when

moving it. Do not wiggle or walk the refrigerator when

trying to move it, as floor damage could occur.

Remove tape and any temporary labels from your

refrigerator before using. Do not remove any warning-

type labels, the model and serial number label, or

the Tech Sheet that is located under the front of the

refrigerator, behind the base grille.

To remove any remaining tape or glue, rub the area

briskly with your thumb. Tape or glue residue can also be

easily removed by rubbing a small amount of liquid dish

soap over the adhesive with your fingers. Wipe with warm

water and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator.

Refrigerator shelves are installed in the shipping position.

Please reinstall shelves according to your individual

storage needs.

Explosion Hazard:

Keep flammable materials and vapors, such as

gasoline, away from the refrigerator. Failure to do so

can result in fire, explosion, or death.

9

PRIOR TO USE

1. Clean your refrigerator thoroughly and wipe off all

dust that accumulated during shipping.

2. Install accessories such as ice cube bin, drawers,

shelves, etc., in their proper places. They are packed

together to prevent possible damage during shipment.

3. Allow your refrigerator to run for at least two to three

hours before putting food in it. Check the flow of

cold air in the freezer compartment to ensure proper

cooling. Your refrigerator is now ready for use.

iNSTALLATiON

The refrigerator should always be plugged into its own

individual properly grounded electrical outlet rated for

115 Volts, 60 Hz, AC only, and fused at 15 or 20 amperes.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a fire

hazard from overheated wires. It is recommended that a

separate circuit serving only this appliance be provided.

Shock Hazard:

To reduce the risk of electric shock, do not install the

refrigerator in a wet or damp area.

INSTALLATION (continued)

lo

To avoid noise and vibration, the unit must be

leveled and installed on a solidly constructed floor. If

required, adjust the leveling legs to compensate for

unevenness of the floor. The front should be slightly

higher than the rear to aid in door closing. Leveling

legs can be turned easily by tipping the cabinet

slightly. Turn the leveling legs clockwise to raise the unit

or counterclockwise to lower it. (See LEVELING AND

DOOR ALIGNMENT.)

NOTE: installing on carpeting, soft tile surfaces,

a platform or weakly supported structure is not

recommended.

o

install this appliance in an area where the temperature

is between 55°F (13°C) and 110°F (43°C). If the

temperature around the appliance is too low or high,

cooling ability may be adversely affected.

Select a place where a water supply can be easily

connected for the automatic Jcemaken

NOTE: The water pressure must be between 20 and

120 psi on models without a water filter and between

40 and 120 psi on models with a water filter.

Too small of a distance from adjacent items may

result in lowered freezing capability and increased

electricity consumption charges. Allow at least 24

inches (61 cm) in front of the refrigerator to open the

doors.

2" (5.08 cm)

10

NOTE: Removing the doors is the recommended procedure when it is necessary to move the refrigerator through a

narrow opening, if it is necessary to remove the handles, follow the directions below.

HOW TO REMOVE REFRIGERATOR

DOOR HANDLE

NOTE: Handle appearance may vary from the

illustrations on this page.

Removing Refrigerator Handle

Loosen the set screws with a 3/32 in. (2.5 ram)

Alien wrench and remove the handle.

Set Screw

Mounting

Fasteners

NOTE: If the handle mounting fasteners need

to be tightened or removed, use a 1/4in. (6.4

mm) Allen wrench.

Allen

Wrench

HOW TO REPLACE REFRIGERATOR

DOOR HANDLE

NOTE: Handle appearance may vary from the

illustrations on this page.

Replacing Refrigerator Door Handle

Place the handle on the door by fitting

the handle footprints over the mounting

fasteners and tightening the set screws

with a 3/32 in (2.5 cm) Allen wrench.

NOTE: If the handle mounting fasteners

need to be tightened or removed, use a

1/4in. (6.4 mm) Allen wrench.

Mounting

Fasteners

11

NOTE: Removing the doors is the recommended procedure when it is necessary to move the refrigerator through a

narrow opening, if it is necessary to remove the handles, follow the directions below.

HOW TO REMOVE FREEZER DOOR HANDLE

NOTE: Handle appearance may vary from the illustrations

on this page.

Removing Freezer Drawer Handle

Loosen the set screws located on the lower side of the

handle with a 1/8in. (3.1 mm) Allen wrench and remove

the handle.

NOTE: If the handle mounting fasteners need to be

tightened or removed, use a 1/4in. (6.4 mm) Allen

wrench.

HOW TO REPLACE FREEZER DOOR HANDLE

NOTE: Handle appearance may vary from the illustrations

on this page.

Replacing Freezer Drawer Handle

Place the handle on the door by fitting the handle

footprints over the mounting fasteners and tightening

the set screws with a 1/8in. (3.1 mm) Allen wrench.

NOTE: If the handle mounting fasteners need to be

tightened or removed, use a 1/4in. (6.4 mm) Allen

wrench.

12

REMOVING AND REPLACING

REFRIGERATOR DOORS

Excessive Weight Hazard:

Use two or more people to remove and install the

refrigerator doors. Failure to do so can result in back or

other injury.

Electrical Shock Hazard

* Disconnect the electrical supply to the refrigerator

before installing. Failure to do so could result in

serious injury or death.

* Do not put hands, feet or other objects into the air

vents or bottom of the refrigerator. You may be

injured or receive an electrical shock.

NOTE: Be careful when you work with the hinge. You may

be injured.

To remove the left refrigerator door:

On the back of the refrigerator, pull the water tube out of

the collet fitting on the connector by pressing the fitting

release ring (see picture below).

_IL CAUTION: Before you begin, remove food and bins

from the doors.

(3).

/

y /

(7) i

(8) I

\

1.Open the door. Remove the top hinge cover screw (1).

Lift up the cover (2).

2. Remove the cover.

3. Pull out the tube (3).

4. Disconnect all wire harnesses (4).

5. Remove the grounding screw (5).

6. Rotate the hinge lever (6) counterclockwise. Lift the top

hinge (7) free of the hinge lever latch (8).

AILCAUTION: When lifting the hinge free of the latch,

be careful that the door does not fall forward.

Z Lift the door from the middle hinge pin and remove the

door.

8. Place the door, inside facing up, on a non-scratching

surface.

To remove the right refrigerator door:

f

_(2)

(i)....

" :/(3) (4)

1.Open the door. Remove the top hinge cover screw (1).

Lift up the cover (2).

2. Remove the cover.

3. Rotate the hinge lever (3) clockwise. Lift the top hinge

(4) free of the hinge lever latch (5).

,A CAUTION: When lifting the hinge free of the latch, be

careful that the door does not fall forward.

4. Lift the door from the middle hinge pin and remove

the door.

5. Place the door, inside facing up, on a non-scratching

surface.

13

Relnstalllng the Refrigerator Door

Left Door

1. Lower the door onto the middle hinge pin (10).

2. Fit the top hinge (7) over the hinge lever latch (8) and into

place. Rotate the lever (6) clockwise to secure the hinge.

3. Install the grounding screw (5) and connect the two

wire harnesses (4).

4. Push the water tube (3) located at the top of the left

door into the hole beside the left hinge on the top of

the cabinet until it exits through the back.

5. Insert the water supply tube (3) into the connector until

you see only one scale mark. Fully insert the tube over

5/8in. (15 mm).

6. Hook the tabs on the left side of the hinge cover (1)

under the edge of the top hinge (7) and position the

cover in place. Insert and tighten the cover screw (1).

(2) (1)

(3).

/

y /

(7)

(8)

Right Door

1. Lower the door onto the middle hinge pin (9).

2. Fit the top hinge (4) over the hinge lever latch (5) and

into place. Rotate the lever (3) counterclockwise to

secure the hinge.

3. Hook the tabs on the right side of the hinge cover (2)

under the edge of the top hinge (4) and position the

cover in place. Insert and tighten the cover screw (1).

_(2)

(1).

' _(3) (4)

(10)

_ _(9)

,CAUTION

Cotlet

Tube

Scale Mark

Clip --

After inserting, pull the tube to

make sure that it is secure and

reinsert the clip.

...............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................J

14

HOW TO REMOVE THE FREEZER DRAWER

_WARNING: Use two or more people to remove and

install the freezer drawer. Failure to do so can result in

back or other injury.

_t_CAUTION: Do not hold the handle when removing or

replacing the drawer. The handle may come off and it

could cause personal injury.

NOTE: In the following figures, the Pullout Drawer

located above the freezer drawer is not shown for

clarity.

Pull the drawe open to full extension. Remove the

lower basket C) by lifting the basket from the rail

system.

Remove the screws (_ from the rail on both sides.

HOW TO INSTALL THE FREEZER DRAWER

With both hands, hold the center bar and putt it out

until both rails are fully extended.

Grasp the drawer on each side and hook the door

supports (_) into the rail tabs C) located on both

sides.

Lower the door into its final position and tighten the

screws C) located on both sides.

Grasp the drawer on each side and putt it up to

separate it from the rails.

With the drawer pulled out to full extension, insert the

lower basket (_ in the rail assembly.

With both hands, hold the center bar and push it in to

allow both rails to slide in simultaneously.

_WARNING: If the Durabase divider is removed, there is

enough open space for children or pets to crawl inside.

To prevent accidental child and pet entrapment or

suffocation, DO NOT allow them to touch or go

near the freezer drawer.

_WARNING: DO NOT step or sit down on the freezer

drawer.

15

LEVELING AND DOOR ALIGNMENT

Leveling

After installing, plug the refrigerator's power cord into a

3-prong grounded outlet and push the refrigerator into the

final position.

Your refrigerator has two front leveling legs--one on the

right and one on the left. Adjust the legs to alter the tilt

from front-to-back or side-to-side. If your refrigerator

seems unsteady, or you want the doors to close more

easily, adjust the refrigerator's tilt using the instructions

below:

NOTE: Tools required: 11/16" (18mm) wrench or fiat blade

screwdriver.

1. Turn the leveling leg counterclockwise to raise that

side of the refrigerator or clockwise to lower it. it may

take several turns of the leveling leg to adjust the tilt

of the refrigeraton

o

Open both doors again and check to make sure that

they close easily. If the doors do not close easily, tilt

the refrigerator slightly more to the rear by turning

both leveling legs counterclockwise. It may take

several more turns, and you should turn both leveling

legs the same amount.

NOTE: Your refrigerator is uniquely designed with

two fresh food doors. Either door can be opened or

closed independently of the other. You may have to

exert slight pressure on the doors to get them to close

completely.

Door Alignment

Both the left and right refrigerator doors have an

adjustable nut, located on the bottom hinge, to raise and

lower them to align properly.

If the space between your doors is uneven, follow the

instructions below to align the doors evenly:

Use the wrench (included with the Use & Care Guide) to

turn the nut in the door hinge to adjust the height. Turn

the nut clockwise to raise or counterclockwise to lower the

door.

NOTE: Having someone push backward against the top of

the refrigerator takes some weight off of the leveling legs.

This makes it easier to adjust the legs.

16

SETTING THE CONTROLS

The refrigerator controt functions as the thermostat for the

entire appliance (refrigerator and freezer sections). The

colder the setting, the longer the compressor will run to

keep the temperature colder. The freezer controt adjusts

the cold air flow from the freezer to the refrigerator.

Setting the freezer controt to a lower temperature keeps

more cold air in the freezer compartment to make it

colder.

AIRFLOW

Cold air circulates from the freezer to the fresh food

section and back again through air vents in the wall

dividing the two sections. Be sure not to block vents while

packing your refrigerator. Doing so will restrict airflow

and may cause the refrigerator temperature to become

too warm or cause interior moisture buildup. (See air flow

diagram below.)

! i.....................................i i

Temperature

The Refrigerator Temp. Control ranges from 33°F to

46°F (0°C to 8°C). Press the Refrigerator Temp. button

to cycle through the available temperature settings one

increment at a time.

The Freezer Temp. Control range is from -6°F to 8°F

(-21°C to -13°C). Pressthe Freezer Temp. button to

cycle through the available temperature settings one

increment at a time.

NOTE: When changing control settings, wait 24 hours

before making additional adjustments. The controls are set

correctly when milk or juice is as cold as you would like

and when ice cream is firm. If the temperature in either

compartment is too cold or too warm, change the setting

one increment at a time. Wait 24 hours for the change to

stabilize before adjusting again.

Dispenser

When you press the Water

button, the water icon will

illuminate.

When you press the Ice Select

button, either the cubed or

crushed ice icon will illuminate.

Some dripping may occur

after dispensing. Hold your cup

beneath the dispenser for a few

seconds after dispensing to catch

all of the drops.

_, CAUTION: The control display is operated by

touch. Excessive moisture on the display may cause a

malfunction. Please keep the display clean and dry.

,_ WARNING: The dispenser will not work if any door is

left open or if the control lock is engaged.

Ultra ice

When you touch the Ultra Ice button, the graphic will

illuminate in the display and will continue for 24 hours.

The function will automatically shut off after 24 hours.

You can stop this function manually by touching the

button one more time.

* This function increases both ice making and freezing

capabilities.

Water Filter Reset L._

CHANGE FILTER

When the water filter indicator turns on, you have

to change the water filter. After changing the water

filter, press and hold the Ultra Ice (Water Filter Reset)

button for three seconds to turn the indicator light off.

You need to change the water filter approximately

every six months.

©

Blue Ambient Mood Light @

This light has two settings: On and Off. If the light is

set to the On mode, the Blue Ambient Mood Light will

turn on.

17

Air Filter _ MAX

CHANGE AIR FILTER

The Air Filter helps remove odors from the

refrigerator. The Air Filter has two settings, Auto ad

MAX. In Auto mode, the Air Filter will cycle on and

of in increments of ten minutes on and 110 minutes

off. If set to the MAX mode, the Air Filter will stay

on continuously for four hours, cycling on and of in

increments of ten minutes on and five minutes of.

After four hours, the Air Filter witl switch to Auto

mode.

* Auto mode is the default mode.

* Press the Air Filter button once for MAX mode.

MAX

Air Filter Reset

CHANGE AIR FILTER

When the CHANGE AIR FILTER icon turns on, the air

filter needs to be replaced. After replacing the air

filter, press and hold the Air Filter button for three

seconds to turn the icon light of. It is recommended

to change the air filter approximately every six months.

Articulating Mullion

This feature is a metal strip attached to the left door

that articulates (rotates) 90 degrees as the door is

closed, forming a mullion (base) for the left and right

door gaskets to seal against.

CAUTION

To reduce the risk of scratching the door or breaking the

door mullion, make sure that the refrigerator door mullion

is always folded in.

Control Lock _R_o_o

When power is initially connected to the refrigerator,

the Lock function is of.

if you want to activate the Lock function to tack other

buttons, press and hold the Door Alarm button for

three seconds or more. The Control Lock icon will

display and the Lock function is now enabled.

* When the Lock function is activated, no other buttons

will work. The dispenser pad is also deactivated.

* To disable the Lock function, press and hold the Door

Alarm button for approximately three seconds.

Temperature Mode Switch Function (°F <->°C)

if you want to convert °F to °C or vice versa, press and

hotd the Freezer Temp. and Refrigerator Temp. buttons at

the same time for approximately five seconds.

Display Off Mode

When the refrigerator is in the Display Off: Mode,

the display will remain off until a door is opened

or a button is pressed. Once on, the display will

remain on for 20 seconds.

To deactivate the Display Off: Mode, press the

Freezer Temp. and Ultra Ice buttons at the same

time and hold them for five seconds until the tone

sounds (in some models).

,A CAUTION

Dema Mode (For Store Use Only)

The Demo Mode disables all cooling in the refrigerator

and freezer sections to conserve energy while on display

in a retail store. When activated, OFF will display on the

control panel.

Door Alarm (_)

When power is connected to the refrigerator, the door

alarm is initially set to ON. When you press the Door

Alarm button, the display will change to OFF and the

Door Alarm function will deactivate.

When either the refrigerator or the freezer door is teft

open for more than 60 seconds, the alarm tone will

sound to let you know that the door is open.

When you close the door, the door alarm witl stop.

To deactivate:

With either refrigerator door opened, press and hotd the

Refrigerator Temp. and Ultra Ice buttons at the same

time for five seconds. The control panel will beep and the

temperature settings witl display to confirm that Demo

Mode is deactivated. Use the same procedure to activate

the Demo Mode.

18

IN-DOOR iCE BiN

,A_CAUTION

Keep hands and tools out of the ice compartment door

and dispenser chute. Failure to do so may result in

damage or personal injury.

The icemaker will stop producing ice when the in-door ice

bin isfull. if you need more ice, empty the ice bin into the

extra ice bin in the freezer compartment. During use, the

ice can become uneven causing the icemaker to misread

the amount of ice cubes and stop producing ice. Shaking

the ice bin to level the ice within it can reduce this problem.

NOTE: Storing cans or other items in the ice bin will

damage the icemaker.

Keep the ice compartment door closed tightly, if the ice

compartment door is not closed tightly, the cold air in the

ice bin will freeze food in the refrigerator compartment.

This could also cause the icemaker to stop producing ice.

NOTE: If the ON/OFF switch on the icemaker is set to

OFF for an extended period of time, the ice compartment

will gradually warm up to the temperature of the

refrigerator compartment. To prevent ice cubes from

melting and leaking from the dispenser, ALWAYS empty

the ice bin when the icemaker is set to OFF for more than

a few hours.

2. To remove the in-door ice bin, grip the front handle,

slightly lift the lower part, and slowly putt out the bin

as shown.

3. To reinstall the in-door ice bin, slightly slant the

bin during replacement to avoid contact with the

icemaker.

,& CAUTION

When handling the

ice bin, keep hands

away from the

4. Avoid touching the ice-detecting sensor when

replacing the ice bin. See the label on the ice

compartment door for details.

1. Putt or push the door handle to open or close the ice

compartment.

19

AUTOMATIC ICEMAKER

Ice is made in the automatic icemaker and sent to the

dispenser. The icemaker will produce 10 cubes per cycle--

approximately 100 cubes in a 24-hour period, depending

on freezer compartment temperature, room temperature,

number of door openings and other operating conditions.

It takes about 12 to 24 hours for a newly installed

refrigerator to begin making ice. Wait 72 hours for full

ice production to occur.

* Ice making stops when the in-door ice bin is full. When

full, the in-door ice bin holds approximately 6 to 8 (12-

16 oz) glasses of ice.

* To turn off the automatic icemaker, set the icemaker

switch to OFF (O). To turn on the automatic icemaker,

set the switch to ON (I).

The water pressure must be between 20 and

120 psi on models without a water filter and between

40 and 120 psi on models with a water filter to

produce the normal amount and size of

ice cubes.

Foreign substances or frost on the ice-detecting sensor

can interrupt ice production. Make sure the sensor area

is clean at all times for proper operation.

Personal Injury Hazard

DO NOT place fingers or hands on the automatic ice

making mechanism while the refrigerator is plugged in.

Icemaker

Power Switch

Ice-detecting Sensor

2O

La page charge ...

Kenmore Elite 79573133410 Le manuel du propriétaire

Ce manuel convient également à

Kenmore Elite 79573133410 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents