Vinten Osprey Light Operator Guide

V3950-0001

V3950-0002

Operating instructions

V3950-4980/3

CN

JP

Osprey Light Pedestal

Osprey Light

Pedestal

Publication Part No. V3950-4980

Issue 3

English . . . . . . . . . . . . . . . . . . . Page 5

Deutsch . . . . . . . . . . . . . . . . . . Seite 29

Español . . . . . . . . . . . . . . . . .Página 53

Français . . . . . . . . . . . . . . . . . . Page 77

Italiano . . . . . . . . . . . . . . . . .Pagina 101

Português . . . . . . . . . . . . . .Página 125

Ꭳᒍ⠰

. . . . . . . . . . . . . . . . . .

?ПȀ

149

Ђ᭜

. . . . . . . . . . . . . . . . . . . . .

乊ⷖ

173

transmitted, copied or reproduced in any way including, but not limited to, photocopy, photograph,

magnetic or other record without the prior agreement and permission in writing of

Vitec Group plc.

Vinten® and Quickfix® are registered trademarks of Vitec Group plc.

Understanding these instructions

English

The original instructions presented in this operators guide were written in English, and

subsequently translated into other languages. If you are unable to understand these

instructions, contact Vinten or your distributor to obtain a translation of the original instructions

(EU Countries).



 ,      ,

    ,    -    .  

  ,    Vinten    ,   

  (    ).

esky

Pokyny uvedené v této operátorské píruce byly pvodn napsány anglicky a následn byly

pelo_eny do ostatních jazyk. Nerozumíte-li tmto pokynm, kontaktujte spolenost Vinten

nebo svého distributora, abyste získali peklad originálních pokyn (lenské státy EU).

Danish

De originale instruktioner, der præsenteres i denne betjeningsvejledning, er skrevet på engelsk

og derefter oversat til andre sprog. Hvis du ikke forstår disse instruktioner bedes du kontakte

Vinten eller vor forhandler for at få en oversættelse af de originale instruktioner (EU-lande).

Deutsch

Die Originalanleitung in diesem Bedienungshandbuch wurde auf Englisch verfasst und

anschließend in andere Sprachen übersetzt. Bei Verständnisproblemen in einer der übersetzten

Sprachen kontaktieren Sie bitte Vinten oder Ihren Fachhändler; dort erhalten Sie eine

Übersetzung der ursprünglichen Anleitung (EU-Staaten).

Eesti

Käesoleva kasutajajuhendi algtekst on koostatud inglise keeles ning seejärel tõlgitud teistesse

keeltesse. Kui juhend osutub teie jaoks arusaamatuks, võtke juhendi emakeelse tõlke

hankimiseks ühendust Vinteni või kohaliku esindajaga (Euroopa Liidu riigid).



            

     .      

,    Vinten          

  ( ).

Español

Las instrucciones originales que se indican en esta guía del operador se han redactado en

inglés y posteriormente se han traducido a otros idiomas. Si no entiende estas instrucciones,

póngase en contacto con Vinten o con su distribuidor para obtener una traducción de las

instrucciones originales (para países de la UE).

Français

Les instructions originales présentées dans ce guide d'utilisation ont été écrites en anglais puis

traduites dans d'autres langues. Si vous ne comprenez pas ces instructions, contactez Vinten

ou votre revendeur pour obtenir une traduction des instructions originales (pour les pays de

l'UE).

English

3

Gaeilge

Scríobhadh na treoracha bunaidh don treoirleabhar oibritheora seo as Béarla, agus aistríodh iad

go teangacha eile ina dhiaidh sin. Mura bhfuil tú in ann na treoracha seo a thuiscint, téigh i

dteagmháil le Vinten nó le do dháileoir, chun aistriúchán de na treoracha bunaidh a fháil (Tíortha

an AE).

Italiano

Le istruzioni originali presentate in questa guida per l'operatore sono in lingua inglese e

successivamente tradotte nelle altre lingue. Qualora le istruzioni non fossero disponibili nella

lingua desiderata, potete contattare Vinten o il vostro distributore per ricevere la traduzione delle

istruzioni originali (Paesi UE).

Latviešu

Šaj operatora rokasgrmat iekautie nordjumi skotnji tika sarakstti angu valod un pc

tam prtulkoti cits valods. Ja nesaprotat šos nordjumus svešvalod, sazinieties ar Vinten

vai tirgotju, lai saemtu nordjumu tulkojumu (kd no ES dalbvalstu valodm).

Lietuvi

Šiame operatoriaus vadove pristatomos pirmins instrukcijos parašytos angl kalba ir vliau

išverstos  kitas kalbas. Jei ši instrukcij nesuprantate, susisiekite su „Vinten“ arba savo

platintoju ir gaukite pirmini instrukcij vertim (ES šalies kalba).

Magyar

A kezeloi útmutatóban található utasítások angol nyelven íródtak, és utólag fordították azokat

más nyelvekre. Ha nem érti ezen utasításokat, kérjük, vegye fel a kapcsolatot a Vintennel vagy

a helyi képviselettel, és igényelje az eredeti utasítások fordítását (EU országok).

Malti

L-istruzzjonijiet originali ippreentati f'din il-gwida ta' operaturi kienu miktuba bl-Ingli, u

sussegwentement maqluba fl-lingwi ohra. Jekk ma tistax tifhem dawn l-istruzzjonijiet, ikkuntattja

lil Vinten jew id-distributur tieghek biex tikseb traduzzjoni ta' l-istruzzjonijiet originali (Pajjii ta'

UE).

Nederlands

De oorspronkelijke instructies in deze bedieningshandleiding zijn geschreven in het Engels en

vervolgens in andere talen vertaald. Als het onmogelijk is deze instructies te begrijpen, neemt u

contact op met Vinten of met uw distributeur om een vertaling te bemachtigen van de

oorspronkelijke instructies (EG-landen).

Polski

Oryginalne instrukcje zamieszczone w niniejszym podrczniku operatora zostay napisane w

jzyku angielskim, a nastpnie przetumaczone na inne jzyki. Jeli nie rozumiej Pastwo tych

instrukcji, prosimy skontaktowa si z siedzib lub dystrybutorem Vinten, aby uzyska

tumaczenie oryginalnych instrukcji (kraje UE).

Português

As instruções originais apresentadas no guia do operador foram escritas em Inglês e traduzidas

para outros idiomas. Se não conseguir compreender estas instruções contacte a Vinten ou o

seu distribuidor para obter a tradução das instruções originais (Países da UE).

English

4

Român

Instruciunile originale prezentate în acest ghid pentru operatori au fost scrise în limba englez,

i traduse ulterior în alte limbi. În cazul în care nu înelegei aceste instruciuni, contactai Vinten

sau distribuitorul dumneavoastr pentru a obine o traducere a instruciunilor originale (rile

UE).

Slovensky

Pôvodné pokyny, uvedené v tomto návode na obsluhu, boli napísané v anglictine a následne

preložené do iných jazykov. Ak nerozumiete týmto pokynom, obrátte sa na spolocnost Vinten

alebo vášho distribútora, aby vám zaslal preklad originálnych pokynov (krajiny EÚ).

Slovenšina

Originalno besedilo teh navodil za uporabo je bilo napisano v anglešini in prevedeno v ostale

jezike. e ne razumete teh navodil, se obrnite na podjetje Vinten ali lokalnega zastopnika, ki

vam bo posredoval originalna navodila (velja za dr_ave EU).

Suomi

Tähän käyttäjän oppaaseen sisältyvät ohjeet on kirjoitettu alun perin englanniksi ja käännetty

sitten muille kielille. Ellet ymmärrä näitä ohjeita, ota yhteyttä Vinteniin tai jälleenmyyjään ja

pyydä alkuperäisten ohjeiden käännöstä (EU-maat).

Svenska

Instruktionerna i denna handbok skrevs ursprungligen på engelska och har sedan översatts till

flera språk. Om du inte förstår dessa instruktioner, kontakta Vinten eller din återförsäljare för en

ny översättning av originalinstruktionerna (EU-länder).

English

5

Preface

Thank you and congratulations on your new Osprey Light pedestal

from Vinten

We want you to get the most from your new pedestal, and therefore encourage you to read this operators

guide to familiarise yourself with its many features, some of which may be new to you. It also covers es-

sential health and safety information and a section on maintenance that will ensure you keep your new

product in perfect condition.

To receive additional benefits, register with Vinten now, on line by visiting www.vinten.com/register, or

by completing the enclosed form.

Features and benefits of your new Osprey Light pedestal

The Osprey Light pedestal has been specifically designed to meet the exacting demands of camera oper-

ators working with lightweight studio cameras. The Osprey Light pedestal offers a high level of control with

many unique features.

• Suitable for a wide range of professional lightweight studio camera/pan and tilt head config-

urations up to 40 kg (88 lb).

• Small footprint allows the pedestal to access tight set situations

• All three wheels are permanently locked together to provide crab steering

• Built-in pump means that the pedestal can be pressurised at any location

• On-shot stroke of 54 cm (21.3 in.) and a maximum height of 131.8 cm (51.9 in.) provide in-

creased creative angles

• Pedestal breaks down into skid and column for easy transportation

Once again, thank you for choosing the Osprey Light pedestal

We are confident it will give you many years of reliable

performance

English

6

English

7

Safety - read this first

English—Original Instructions

The original instructions presented in this operators guide were written in English, and subsequently trans-

lated into other languages. If you are unable to understand any of the translated languages, contact Vinten

or your distributor to obtain a translation of the original instructions (EU Countries).

Warning Symbols in this Operators Guide

Where there is a risk of personal injury, injury to others, or damage to the pedestal

or associated equipment, comments appear, highlighted by the word WARNING!

and supported by the warning triangle symbol.

Warning symbols on the pedestal

On encountering the warning triangle and open book symbols it is imperative that

you consult this operators guide before using the pedestal or attempting any adjust-

ment or repair.

Critical data

Load

Maximum load 40 kg (88 lb)

Mass

Column 10.45 kg (23 lb)

Skid - studio 8.45 kg (18.6 lb)

Skid - OB 8.65 kg (19 lb)

Kick ring 2.5 kg (5.5 lb)

Pressure

Maximum pressure 9.6 bar (139 psi)

d40 kg

10.45

kg

8.65

kg

d 9.6 bar

English

8

Regulatory information

This product conforms to the following European Directives:

2006/42/EC (CE Marking Directive)

98/37/EC (Machinery Directive) (89/392/EC)

97/23/EC (Pressure Equipment Directive - SEP)

2001/95/EC (General Product Safety)

This product has been manufactured in accordance with BS EN ISO 9001/2000

Harmonised standards applied:

BS EN ISO 12100-2:2003 (Safety of machinery—Basic Concepts, general principles for design,

Part 2: Technical principles.

BS EN 1050:1997 Safety of machinery—Principles for risk assessment.

In accordance with the following UK Regulations:

SI 1992 No.3037 Supply of Machinery (Safety) Regulations 1992

SI 1994 No.2063 Supply of Machinery (Safety) Regulations—Amendment 1994

SI 1999 No.2001 (SI 2002/1267) UK Pressure Equipment Regulations 1994

English

9

Contents

Page

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety - read this first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Critical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Regulatory information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Further information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Assembling the pedestal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Setting the control valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Pressurizing the pedestal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Fitting and balancing the load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Using the pedestal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Transportation and storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Routine checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

Associated Publication

Osprey Light Pedestal

Maintenance Manual and illustrated Parts List

Publication Part no. V3959-4990

English

10

English

11

Technical data

STUDIO OB

Payload 40 kg (88 lb) 40 kg (88 lb)

Column weight 10.45 kg (23 lb) 10.45 kg (23 lb)

Skid weight 8.45 kg (18.6 lb) 8.65 kg (19 lb)

Kick ring weight 2.5 kg (5.5 lb) 2.5 kg (5.5 lb)

Total pedestal weight (without kick ring) 18.9 kg (41.6 lb) 19.1 kg (42 lb)

Trim weights (4 x 1.0 kg) 4.0 kg (8.8 lb) 4.0 kg (8.8 lb)

Minimum height 76.5 cm (30.1 in.) 77.8 cm (30.6 in.)

Maximum height 130.5 cm (51.4 in.) 131.8 cm (51.9 in.)

On-shot stroke 54 cm (21.3 in.) 54 cm (21.3 in.)

Ground clearance 10 cm (0.4 in.) 2.25 cm (0.9 in.)

Doorway tracking width 80.6 cm (27.5 in.) 80.6 cm (27.5 in.)

Transit doorway width 70 cm (27.5 in.) 70 cm (27.5 in.)

Wheel diameter 10 cm (4 in.) 12.5 cm (5 in.)

Steering ring diameter 50 cm (19.7 in.) 50 cm (19.7 in.)

Maximum working pressure 9.6 bar (139 psi) 9.6 bar (139 psi)

Minimum working pressure 2 bar (29 psi) 2 bar (29 psi)

Relief valve pressure 10 bar (145 psi) 10 bar (145 psi)

Internal capacity 1.9 L (0.50 gal) 1.9 L (0.50 gal)

Operational temperature -20°C / +60°C (-4°F / +140°F) -20°C / +60°C (-4°F / +140°F)

Usage

The Osprey Light pedestal is designed for use in television studios and on location to support and balance

a pan and tilt head, camera and ancillary equipment weighing up to 40 kg (88 lb).

This product is intended for use on an unobstructed and reasonably level surface by television camera op-

erators.

WARNING! 1. Do NOT attempt to use this product if you do not understand how to

operate it.

2. Do NOT use this product for any other purpose than that specified in the

Usage statement above.

3. Maintenance beyond that detailed in this Operators Guide must be per-

formed only by competent personnel in accordance with the procedures

laid down in the Maintenance Manual.

English

12

Further information

For further information or advice regarding this pedestal, please contact Camera Dynamics Limited, your

local Vinten distributor (see back cover) or visit our website.

For details on maintenance and spare parts, please refer to the Osprey Light Pedestal Maintenance Man-

ual and Illustrated Parts List (Publication Part No. V3950-4990) This is obtainable from Vinten or your local

Vinten distributor. For information on-line, visit our website at

www.vinten.com

English

13

Osprey Light Pedestal (Studio Version)

(Fig 1)

(1) Schrader valve and cap

(2) Pressure gauge viewing window

(3) Steering ring

(4) Steering indicator

(5) Moving column

(6) Drag control knob/on-shot clamp

(7) Strut

(8) Foot support and strap

(9) Cable guard adjustment knob

(10) Cable guard

(11) Folding leg

(12) Skid centre casting

(13) Optional kick ring

(14) Skid wheel

(15) Brake

(16) Skid clamp

(17) Fixed leg

(18) Cable clamp

(19) Velcro strap

(20) Steering tube

(21) Outer tube

(22) Trim weight stowage

(23) Trim weight catch

(24) Safety catch

(25) Weight tray pocket

(26) Control valve

(27) Four-bolt mounting plate

(28) Trim weight

English

14

Introduction

The Osprey Light pedestal is a fully-portable pneumatic camera mount, designed to support a payload of

up to 40 kg (88 lb). It is available in OB and Studio versions.

The pedestal has a central single-stage telescopic column, supported on a skid assembly with crabbing

wheel steering. To facilitate transport, the telescopic column and skid may be separated and the skid fold-

ed.

The pedestal may be pressurized using the built-in pump, Vinten Portable Pump or an external pressure

source. The pedestal is equipped with a relief valve to prevent an excessive build-up of pneumatic pressure

and with a safety catch to prevent accidental operation of the telescopic column. The pressure relief valve

operates at the predetermined level and automatically resets at a designated level below this.

The skid assembly comprises a centre casting, three equispaced skid legs and three braked wheels. The

OB version has 12.5 cm (5 in.) wheels, the Studio version 10 cm (4 in.) wheels fitted with cable guards.

English

15

Operation

Assembling the pedestal

(Fig 1) (Fig 2) (Fig 3)

Skid

Turn the skid upside-down, depress the leg locking plungers (11.1) and swing each folding leg (11) out until

the plungers lock the legs in the fully open position.

Fit the optional kick ring (13), which is secured by three sliding catches (13.1) to spigots (12.1) on the un-

derside of the centre casting.

Set the skid on the ground on its wheels and apply the wheel brakes (15).

Column

Install the column on the skid as follows:

Fully slacken the skid clamp (16) and ensure that the rubber straps (8) on each foot support are to

the outside of the ball joint.

Ensure the control valve (26) is set to the WORK position.

Release the Velcro retaining strap (19).

Hold the telescopic column upright with the steering ring uppermost and swing the three struts (7)

up almost to horizontal.

Lift the column assembly by the steering ring (3) and lower it vertically into the skid centre casting,

ensuring that the steering tube (20) engages correctly with the skid. Turn the steering ring to fully

engage the steering tube (20).

Engage the struts (7) on the foot supports (8) and secure each strut to the foot support with the

rubber strap.

Tighten the skid clamp (16), using moderate hand pressure only. The clamp lever has a spring-

loaded ratchet-type action and is operated as follows:

Turn the clamp lever (16) clockwise as far as possible.

Pull the lever outward against the spring pressure, return it to vertical and release.

Turn lever clockwise again.

Repeat until the skid clamp is sufficiently tightened.

Secure the Velcro retaining strap (19) clear of the skid wheels.

Slide the steering indicator (4) to the desired position.

Setting the control valve

The control valve (26) safely switches the pedestal between PUMP and WORK modes, and has three dis-

tinct positions and functions.

Pump

Pump mode isolates the moving column (5) from the full pedestal pressure and engages the built-in pump

mechanism. To select PUMP mode, proceed as follows:

NOTE: The kick ring can be fitted in only one position, with the shorter strut on the fixed leg.

English

16

Depress the control valve (26) against the spring force, and rotate the lever fully clockwise to a hor-

izontal position. The control valve (26) will remain in a depressed position.

Refer to ‘Pressurizing the pedestal using the built-in pump’ on page 17 for self-pumping instructions.

Transition

Transition mode gradually applies the full pedestal pressure to the moving column (5) at a safe rate. To

select TRANSITION mode, proceed as follows:

Fully extend the moving column (5).

Depress the control valve (26) against the spring force, rotate the lever to the vertical position and

allow the lever to extend under the spring force.

Work

Work mode applies the full pedestal pressure to the moving column (5) to balance the payload. To select

WORK mode, proceed as follows:

Ensure the moving column (5) is fully extended.

Depress the control valve (26) against the spring force, and rotate the lever fully counter clockwise

to a horizontal position, allowing the lever (26) to extend under the spring force. The control valve

(26) will remain in an extended position.

Pressurizing the pedestal

The Osprey Light pedestal may be pressurized manually using the self-contained pump, Vinten portable

pump (Part No. 3357-3) or an external pressure source.

A correctly pressurized pedestal will balance its payload, allowing movement over the full on-shot stroke

of the moving column with minimum effort, and will maintain its position when the steering ring is released.

Balance can be adjusted by adding or removing trim weights (28) to the weight tray pockets (25), or venting

some of the internal pressure.

Ascertain the payload to be fitted to the pedestal (payload = pan and tilt head, camera, trim weights, lens

and all ancillary equipment). Referring to the graph (Fig 4), mark the payload on the horizontal axis then

strike a vertical line from the load figure to the balance line. At the intersecting point, strike a horizontal line

to the vertical axis and read off the required gas pressure.

The pedestal pressure must be reduced to a maximum of 3.5 bar (50 psi) before fitting the pan and tilt head

(refer to ‘Fitting and balancing the load’ on page 19 for more detail).

NOTE: Set the control valve (26) to PUMP mode when transporting the pedestal, to isolate the

moving column (5) from internal pressure. Refer to ‘Transportation and storage’ on

page 22 for more information.

WARNING! Place the control valve (26) in the TRANSITION position for at least 10-

SECONDS when switching between PUMP and WORK modes, to prevent

the moving column (5) rising rapidly.

NOTE: The pressure gauge only displays full system pressure when the control valve (26) is

set to WORK.

English

17

To determine the pedestal pressure, proceed as follows:

Ensure that the control valve (26) is set to the WORK position (refer to ‘Setting the control valve’

on page 15).

Rotate the steering ring (3) so that the pressure gauge is visible through the viewing window (2).

Pressurizing the pedestal using the built-in pump

To pressurize the pedestal using the built-in pump, proceed as follows:

Apply the wheel brakes (15).

Set the control valve (26) to the PUMP position as follows:

Depress the control valve (26) against the spring force, and rotate the lever fully clockwise

to a horizontal position. The control valve (26) will remain in a depressed position.

Push down on the steering ring (3) against any residual pressure and release the safety catch (24).

Set the safety catch in the horizontal position.

Rotate the steering ring (3) so that the pressure gauge (2) is visible through the window.

Using the steering ring (3), raise the top stage (5) until fully extended. Commence pumping by low-

ering and raising the top stage (5) over the upper half of its travel. When the pressure gauge (2)

begins to register, pump the top stage over its full stroke.

As pressure increases, put a foot on the skid to restrain the pedestal on the up stroke.

NOTE: Reducing pedestal pressure below 3.5 bar (50 psi) may cause a pressure leak.

WARNING! 1. Do NOT pressurize the pedestal beyond the maximum safe working

pressure indicated by the leading edge of the red sector on the gauge.

2. Do NOT adjust the pressure relief valve. Personal injury and pedestal

damage may occur.

WARNING! If fitted, remove the camera from the pan and tilt head before attempting

to use the built-in pump. The pan and tilt head can remain fitted without

compromising operator safety.

NOTE: The pressure gauge only displays full system pressure when the control valve (26) is

set to WORK.

An approximation of the final pedestal pressure can obtained by observing the peak

pressure reading on the downward pumping stoke.

English

18

Stop pumping when the required pressure is reached (Fig 4) during the pumping stroke. Do not

exceed the maximum working pressure, indicated by the leading edge of the red sector on the

gauge (2).

Fully collapse the moving column (5) and apply the safety catch (24).

Set the control valve (26) to the TRANSITION position as follows:

Depress the control valve (26) against the spring force, rotate the lever to the vertical po-

sition and allow the lever to extend under the spring force.

Set the control valve (26) to the WORK position as follows:

Ensure the moving column (5) is fully collapsed and the safety catch (24) is applied.

Depress the control valve (26) against the spring force, and rotate the lever fully counter

clockwise to a horizontal position, allowing the lever (26) to extend under the spring force.

The control valve (26) will remain in an extended position.

Pressurizing the pedestal using the Vinten portable pump

To pressurize the pedestal using the Vinten portable pump, proceed as follows:

Fully collapse the moving column (5) and apply the safety catch (24).

Set the control valve (26) to the WORK position (refer to ‘Setting the control valve’ on page 15 for

more detail).

Rotate the steering ring (3) so that the pressure gauge is visible through the viewing window (2).

On the pump (Fig 4), fold down both the feet (P.3).

Depress the handle release button (P.5) and move the handle (P.1) to the horizontal position,

where it will lock.

Pull the hose (P.4) out of its stowage (P.2). Connect the hose to the pedestal charging valve.

Position the pump between the legs, standing with both feet on the fold-down feet (P.3).

Grip the handle (P.1) with both hands and, using full steady strokes, pressurize the pedestal to the

required pressure. Do not exceed the maximum working pressure, indicated by the leading edge

of the red sector on the gauge (2).

NOTE: Do not exceed 3.5 bar (50 psi) if the pan and tilt head has yet to be fitted. For further

information refer to ‘Fitting and balancing the load’ on page 19.

WARNING! Place the control valve (26) in the TRANSITION position for at least 10-

SECONDS when switching between PUMP and WORK modes, to prevent

the moving column (5) rising rapidly.

NOTE: Do not exceed 3.5 bar (50 psi) if the pan and tilt head has yet to be fitted. For further

information refer to ‘Fitting and balancing the load’ on page 19.

English

19

Disconnect the hose (P.4) from the pedestal charging valve, but do not refit the Schrader valve cap

at this stage. Fit the hose in its stowage (P.2).

Push the pump plunger fully down, depress the handle release button (P.5) and move the handle

(P.1) to the vertical position, where it will lock the pump plunger in the closed position.

Fold up both the feet (P.3).

Pressurizing from an external pressure source

A pressure reducing valve must be fitted between the gas cylinder and the outlet connection of the hose.

The maximum pressure on the outlet side of the reducing valve must not exceed 9.6 bar (139 psi).

To pressurize the pedestal from an external pressure source, proceed as follows:

Fully collapse the moving column (5) and apply the safety catch (24).

Set the control valve (26) to the WORK position (refer to ‘Setting the control valve’ on page 15 for

more detail).

Rotate the steering ring (3) so that the pressure gauge is visible through the window (2).

Remove the Schrader valve cap (1) and connect the charging line from the pressure source.

Turn on the pressure supply and slowly increase the pedestal pressure to the required pressure.

Do not exceed the maximum working pressure, indicated by the leading edge of the red sector on

the gauge (2).

Disconnect the charging line, but do not refit the Schrader valve cap at this stage.

Fitting and balancing the load

The Osprey Light pedestal has the standard four-bolt mounting plate (27) which permits the use of various

Vinten camera mounts including pan and tilt heads, Quickfix and Mitchell adapters.

Fitting the camera mount

To fit the camera mount, proceed as follows:

Ensure that the control valve (26) is set to the WORK position (refer to ‘Setting the control valve’

on page 15).

WARNING! This pedestal must be pressurized only with clean, dry air or nitrogen.

NOTE: Do not exceed 3.5 bar (50 psi) if the pan and tilt head has yet to be fitted. For further

information refer to ‘Fitting and balancing the load’ below.

La page charge ...

Vinten Osprey Light Operator Guide

Vinten Osprey Light Operator Guide

dans d''autres langues

Documents connexes

Autres documents