MINN KOTA PowerDrive V2 Bow-Mount Trolling Motor Manuel utilisateur

Marque: MINN KOTA

Modèle: PowerDrive V2 Bow-Mount Trolling Motor

Taper: Manuel utilisateur

POWERDRIVE V2

BOW-MOUNT TROLLING MOTOR

USER MANUAL

Model: _________________________________________________________________________________________________________________________

Serial Number: _______________________________________________________________________________________________________________

Purchase Date: _______________________________________________________________________________________________________________

Store Where Purchased: ____________________________________________________________________________________________________

NOTE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair or replace this unit. You may obtain service

by: calling Minn Kota at (800) 227-6433; returning your motor to the Minn Kota Factory Service Center; sending or taking your motor to any

Minn Kota authorized service center. A list of authorized service centers is available on our website, at minnkotamotors.com. Please include proof of

purchase, serial number and purchase date for warranty service with any of the above options.

Please thoroughly read this user manual. Follow all instructions and heed all safety and cautionary notices below. Use of this motor is only

permitted for persons that have read and understood these user instructions. Minors may use this motor only under adult supervision.

ATTENTION: Never run the motor out of the water, as this may result in injuries from the rotating propeller. The motor should be disconnected from

the power source when it is not in use or is oﬀ the water. When connecting the power-supply cables of the motor to the battery, ensure that they are

not kinked or subject to chafe and route them in such a way that persons cannot trip over them. Before using the motor make sure that the insulation

of the power cables is not damaged. Disregarding these safety precautions may result in electric shorts of battery(s) and/or motor. Always disconnect

motor from battery(s) before cleaning or checking the propeller. Avoid submerging the complete motor as water may enter the lower unit through

control head and shaft. If the motor is used while water is present in the lower unit considerable damage to the motor can occur. This damage will not

be covered by warranty.

CAUTION: Take care that neither you nor other persons approach the turning propeller too closely, neither with body parts nor with objects. The

motor is powerful and may endanger or injure you or others. While the motor is running watch out for persons swimming and for ﬂ oating objects.

Persons whose ability to run the motor or whose reactions are impaired by alcohol, drugs, medication, or other substances are not permitted to use

this motor. This motor is not suitable for use in strong currents. The constant noise pressure level of the motor during use is less than 70dB(A). The

overall vibration level does not exceed 2,5m/sec2.

THANK YOU

Thank you for choosing Minn Kota. We believe that you should spend more time ﬁ shing and less time positioning your boat.

That’s why we build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling motor

is thought out and rethought until it’s good enough to bear our name. Countless hours of research and testing provide you the

Minn Kota advantage that can truly take you “Anywhere. Anytime.” We don’t believe in shortcuts. We are Minn Kota. And we are

never done helping you catch more ﬁ sh.

REMEMBER TO KEEP YOUR RECEIPT AND IMMEDIATELY REGISTER YOUR TROLLING MOTOR.

A registration card is enclosed or you can complete registration on our website at minnkotamotors.com.

LOCATING YOUR SERIAL NUMBER

Your Minn Kota 11-character serial number is very important. It helps to determine the speciﬁ c model and year of manufacture. When contacting

Consumer Service or registering your product, you will need to know your product’s serial number. We recommend that you write the serial number

down in the space provided below so that you have it available for future reference.

CE MASTER USER MANUAL (FOR CE/C-TICK CERTIFIED MODELS)

Conforms to 89/336/EEC (EMC) under standards EN 55022A, EN 50082-2 since 1996 LN V9677264

Made by Minn Kota

Johnson Outdoors

Marine Electronics, Inc.

121 Power Drive

Mankato, MN 56001 USA

Trolling Motors

Produced in 2012

PowerDrive V2

MODEL 1358710

SER NO M365 MK12345

EXAMPLE

The serial number on your PowerDrive V2 is

located inside the mount below the motor rests.

minnkotamotors.com | 3

TABLE OF CONTENTS

Two-Year Limited Warranty 4

Features 5

Mount Installation 6

Battery & Wiring Installation 7-8

Boat Rigging & Product Installation 7

Conductor Gauge and Circuit Breaker Sizing Table 7

Push-to-test Battery Meter 7

Selecting the Correct Batteries 8

Connecting the Batteries 8

Motor Wiring Diagram 9

Using The Motor 10-12

Stowing & Deploying 10

AutoPilot Controls 11

Adjusting the Depth of the Motor 11

Installing an External Transducer 12

Using the Foot Pedal 13

Service & Maintenance 14

Troubleshooting 15

Parts Diagram 16

Parts List 17

Environmental Compliance Statement 18

Notes 19

WARRANTY ON MINN KOTA FRESHWATER TROLLING MOTORS

Johnson Outdoors Marine Electronics, Inc. (“JOME”) extends the following limited warranty to the original retail purchaser only. Warranty coverage is not

transferable.

MINN KOTA LIMITED TWO-YEAR WARRANTY ON THE ENTIRE PRODUCT

JOME warrants to the original retail purchaser only that the purchaser’s new Minn Kota freshwater trolling motor will be materially free from defects in materials

and workmanship appearing within two (2) years after the date of purchase. JOME will (at its option) either repair or replace, free of charge, any parts found by

JOME to be defective during the term of this warranty. Such repair, or replacement shall be the sole and exclusive liability of JOME and the sole and exclusive

remedy of the purchaser for breach of this warranty.

MINN KOTA LIMITED LIFETIME WARRANTY ON COMPOSITE SHAFT

JOME warrants to the original retail purchaser only that the composite shaft of the purchaser’s Minn Kota trolling motor will be materially free from defects in

materials and workmanship appearing within the original purchaser’s lifetime. JOME will provide a new composite shaft, free of charge, to replace any composite

shaft found by JOME to be defective during the term of this warranty. Providing a new composite shaft shall be the sole and exclusive liability of JOME and the

sole and exclusive remedy of the purchaser for breach of this warranty; and purchaser shall be responsible for installing, or for the cost of labor to

install, any new composite shaft provided by JOME.

EXCLUSIONS & LIMITATIONS

This limited warranty does not apply to products that have been used in saltwater or brackish water, commercially or for rental purposes. This limited warranty

does not cover normal wear and tear, blemishes that do not aﬀ ect the operation of the product, or damage caused by accidents, abuse, alteration, modiﬁ cation,

shipping damages, acts of God, negligence of the user or misuse, improper or insuﬃ cient care or maintenance. DAMAGE CAUSED BY THE USE OF

OTHER REPLACEMENT PARTS NOT MEETING THE DESIGN SPECIFICATIONS OF THE ORIGINAL PARTS WILL NOT BE COVERED BY

THIS LIMITED WARRANTY. The cost of normal maintenance or replacement parts which are not in breach of the limited warranty are the responsibility

of the purchaser. Prior to using products, the purchaser shall determine the suitability of the products for the intended use and assumes all related risk and

liability. Any assistance JOME provides to or procures for the purchaser outside the terms, limitations or exclusions of this limited warranty will not constitute

a waiver of the terms, limitations or exclusions, nor will such assistance extend or revive the warranty. JOME will not reimburse the purchaser for any expenses

incurred by the purchaser in repairing, correcting or replacing any defective products or parts, except those incurred with JOME’s prior written permission.

JOME’S AGGREGATE LIABILITY WITH RESPECT TO COVERED PRODUCTS IS LIMITED TO AN AMOUNT EQUAL TO THE PURCHASER’S

ORIGINAL PURCHASE PRICE PAID FOR SUCH PRODUCT.

MINN KOTA SERVICE INFORMATION

To obtain warranty service in the U.S., the product believed to be defective, and proof of original purchase (including the date of purchase), must be presented

to a Minn Kota Authorized Service Center or to Minn Kota’s factory service center in Mankato, MN. Any charges incurred for service calls, transportation or

shipping/freight to/from the Minn Kota Authorized Service Center or factory, labor to haul out, remove, re-install or re-rig products removed for warranty service,

or any other similar items are the sole and exclusive responsibility of the purchaser. Products purchased outside of the U.S. must be returned prepaid with

proof of purchase (including the date of purchase and serial number) to any Authorized Minn Kota Service Center in the country of purchase. Warranty service

can be arranged by contacting a Minn Kota Authorized Service Center or by contacting the factory at 1-800-227-6433 or email service@minnkotamotors.com.

Products repaired or replaced will be warranted for the remainder of the original warranty period [or for 90 days from the date of repair

or replacement, whichever is longer]. For any product that is returned for warranty service that JOME ﬁ nds to be not covered by or not

in breach of this limited warranty, there will be a billing for services rendered at the prevailing posted labor rate and for a minimum of at

least one hour.

NOTE: Do not return your Minn Kota product to your retailer. Your retailer is not authorized to repair or replace products.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIMITED WARRANTIES. IN NO EVENT SHALL ANY IMPLIED

WARRANTIES INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXTEND

BEYOND THE DURATION OF THE RELEVANT EXPRESS LIMITED WARRANTY. IN NO EVENT SHALL JOME BE LIABLE FOR PUNITIVE,

INDIRECT, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. Without limiting the foregoing, JOME assumes no responsibility for

loss of use of product, loss of time, inconvenience or other damage.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above

limitations and/or exclusions may not apply to you. This warranty gives you speciﬁ c legal rights and you may also have other legal rights which vary from state

to state.

TWO-YEAR LIMITED WARRANTY

minnkotamotors.com | 5

FEATURES

Speciﬁcations subject to change without notice.

*This diagram is for reference only and may diﬀer from your actual motor.

Weedless Wedge 2 Propeller

Adjustable Depth Collar

Lifetime

Warranty Flexible

Composite Shaft

Low Proﬁle

Foot Pedal

Cool Quiet

Power Motor

Deploy-Assist

Lever

Tilt Lock Lever

MOUNT INSTALLATION

TOOLS AND RESOURCES REQUIRED:

• #3 Phillips Screw Driver

• Drill

• 9/32” Drill Bit

• 7/16” Box End Wrench

• A second person to help with the installation

1. Remove the four sideplate screws. Remove the right sideplate and swing the left sideplate out and away from the base

extrusion.

2. Place the motor on the bow of the boat in the deployed position.

a. We recommend that the motor be mounted as close to the centerline of the boat as possible.

b. Make sure that the area under the mounting location is clear and unobstructed

for drilling and accessible for you to attach nuts and washers.

c. Make sure the mount is positioned so that the shaft is out beyond the rub rail of the boat by 1-½”. The lower unit, as it is

lowered into the water or raised into the boat, must not encounter any obstructions.

CAUTION: Make sure the motor is mounted on a level surface and is not connected to

a power source. Use the rubber washers to create a level surface if necessary.

3. Once in position, mark four of the twelve holes (two on each side) provided in the bow mount base for drilling. If possible, use

the four holes that are farthest apart. Drill through the marked holes using the 9/32” drill bit.

4. Mount the plate to the bow using the provided bolts, nuts, and washers.

5. Replace the sideplates and sideplate screws.

Mounting Holes

(6 Per Side)

BOAT RIGGING & PRODUCT INSTALLATION

For safety and compliance reasons, we recommend that you follow American Boat and Yacht Council (ABYC) standards when

rigging your boat. Altering boat wiring should be completed by a qualiﬁ ed marine technician. The following speciﬁ cations are for

general guidelines only:

CAUTION: These guidelines apply to general rigging to support your Minn Kota motor. Powering multiple motors or additional

electrical devices from the same power circuit may impact the recommended conductor gauge and circuit breaker size. If you are

using wire longer than that provided with your unit, follow the conductor gauge and circuit breaker sizing table below. If your wire

extension length is more than 25 feet, we recommend that you contact a qualiﬁ ed marine technician.

An over-current protection device (circuit breaker or fuse) must be used. Coast Guard requirements dictate that

each ungrounded current-carrying conductor must be protected by a manually reset, trip-free circuit breaker or fuse. The type

(voltage and current rating) of the fuse or circuit breaker must be sized accordingly to the trolling motor used. The table below gives

recommended guidelines for circuit breaker sizing.

Reference:

United States Code of Federal Regulations: 33 CFR 183 – Boats and Associated Equipment

ABYC E-11: AC and DC Electrical Systems on Boats

CONDUCTOR GAUGE AND CIRCUIT BREAKER SIZING TABLE

Motor Thrust /

Model Max Amp Draw Circuit Breaker Wire Extension Length *

5 feet 10 feet 15 feet 20 feet 25 feet

30 lb. 30 50 Amp @ 12 VDC 10 AWG 10 AWG 8 AWG 6 AWG 4 AWG

40 lb., 45 lb. 42 10 AWG 8 AWG 6 AWG 4 AWG 4 AWG

50 lb., 55 lb. 50 60 Amp @ 12 VDC 8 AWG 6 AWG 4 AWG 4 AWG 2 AWG

70 lb. 42 50 Amp @ 24 VDC 10 AWG 10 AWG 8 AWG 8 AWG 6 AWG

80 lb. 56 60 Amp @ 24 VDC 8 AWG 8 AWG 8 AWG 6 AWG 6 AWG

101 lb. 46 50 Amp @ 36 VDC 8 AWG 8 AWG 8 AWG 8 AWG 8 AWG

Engine Mount 101 50 60 Amp @ 36 VDC 8 AWG 6 AWG 4 AWG 4 AWG 2 AWG

112 lb. 52 60 Amp @ 36 VDC 8 AWG 8 AWG 8 AWG 8 AWG 8 AWG

Engine Mount 160 116 (2) x 60 Amp @ 24 VDC 2 AWG 2 AWG 2 AWG 2 AWG 2 AWG

E-Drive 40 50 Amp @ 48 VDC 10 AWG 10 AWG 10 AWG 10 AWG 10 AWG

This conductor and circuit breaker sizing table is only valid for the following assumptions:

1. No more than 3 conductors are bundled together inside of a sheath or conduit outside of engine spaces.

2. Each conductor has 105° C temp rated insulation.

3. No more than 5% voltage drop allowed at full motor power based on published product power requirements.

*Wire Extension Length refers to the distance from the batteries to the trolling motor leads.

minnkotamotors.com | 7

BATTERY WIRING & INSTALLATION

PUSH-TO-TEST BATTERY METER

This motor is equipped with a “push-to-test” battery meter. The LED provides an accurate

display of the remaining charge in the battery. It is only accurate when the motor is oﬀ .

The meter reads as:

• One light indicates recharge.

• Two lights indicate low charge.

• Three lights indicate good charge.

• Four lights indicate full charge.

BATTERY WIRING & INSTALLATION

CONNECTING THE BATTERIES IN SERIES (IF REQUIRED FOR YOUR MOTOR)

24 VOLT SYSTEMS:

1. Make sure that the motor is switched oﬀ (speed selector on “0”).

2. Two 12 volt batteries are required.

3. The batteries must be wired in series, only as directed in wiring

diagram, to provide 24 volts.

a. Connect a connector cable to the positive ( + ) terminal of

battery 1 and to the negative ( – ) terminal of battery 2.

b. Connect positive ( + ) red motor lead to

positive ( + ) terminal on battery 2.

c. Connect negative ( – ) black motor lead to

negative ( – ) terminal of battery 1.

4. For safety reasons do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper

polarity and follow instructions in your boat owner’s manual. See wiring diagram on following pages.

CAUTION

• For safety reasons, disconnect the motor from the battery or batteries when the motor is not in use or while

the battery/batteries are being charged.

• Improper wiring of 24/36 volt systems could cause battery explosion!

• Keep leadwire wing nut connections tight and solid to battery terminals.

• Locate battery in a ventilated compartment.

To trolling motor negative

24 Volt Connection

Battery #1 (Low Side)

Neg - Neg -Pos + Pos +

Battery #2 (High Side)

+24 Volts to trolling motor

positive (or circuit breaker)

24 Volt Series Connection

SELECTING THE CORRECT BATTERIES

The motor will operate with any lead acid, deep cycle marine 12 volt battery/batteries. For best results, use a deep cycle, marine

battery with at least a 105 ampere hour rating. Maintain battery at full charge. Proper care will ensure having battery power

when you need it, and will signiﬁ cantly improve the battery life. Failure to recharge lead-acid batteries (within 12-24 hours) is the

leading cause of premature battery failure. Use a multi-stage charger to avoid overcharging. We oﬀ er a wide selection of chargers

to ﬁ t your charging needs. If you are using a crank battery to start a gasoline outboard, we recommend that you use a separate

deep cycle marine battery/batteries for your Minn Kota trolling motor.

Advice Regarding Batteries:

• Never connect the (+) and the (–) terminals of the same battery together. Take care that no metal object can fall onto the

battery and short the terminals. This would immediately lead to a short and extreme ﬁ re danger.

• It is highly recommended that a circuit breaker or fuse be used with this trolling motor. Refer to “Conductor Gauge and Circuit

Breaker Sizing Table” in the previous section to ﬁ nd the appropriate circuit breaker or fuse for your motor. For motors requiring

a 60-amp breaker, the Minn Kota MKR-19 60-amp circuit breaker is recommended.

CONNECTING THE BATTERIES

12 VOLT SYSTEMS:

1. Make sure that the motor is switched oﬀ (speed selector on “OFF” or “0”).

2. Connect positive ( + ) red lead to positive ( + ) battery terminal.

3. Connect negative ( – ) black lead to negative ( – ) battery terminal.

4. For safety reasons do not switch the motor on until the propeller is in the water.

CAUTION:

For safety reasons, disconnect the motor from the battery/batteries when the motor is not in use or while the

battery/batteries are being charged.

minnkotamotors.com | 9

MOTOR WIRING DIAGRAM

NOTE: This is a universal, multi-voltage diagram. Double check your motor's voltage for proper connections. Over-Current

Protection Devices not shown in this illustration.

B+

B-

M+

M-

12v

24v

COMPASS

SENSOR

BOARD

RED M+

BLACK M-

BROWN

YELLOW

GREEN

RED

BLACK

WHITE

UNIVERSAL SONAR 2

EXTENSION WIRE*

COIL CORD

GREEN

YELLOW

BROWN

RED

BLACK

WHITE

BLACK M-

FUSE*

RED M+

MOTOR

STEERING MOTOR

CONTROL BOARD

RED

BLACK

BATTERY

GAUGE

FOOT PEDAL

CONTROL BOARD*

BATTERY 1

BATTERY 2 BATTERY 3

* ON US2 EQUIPPED MOTORS ONLY

BLACK B-

RED B+

AUTOPILOT EQUIPPED

MOTORS ONLY

USING & ADJUSTING THE MOTOR

STOWING AND DEPLOYING THE MOTOR

WARNING:

When raising or lowering the motor, keep ﬁ ngers clear of all hinge and pivot points and all moving parts.

DEPLOY-ASSIST LEVER OPERATION:

1. Loosen the depth collar screw.

2. Push Deploy-Assist Lever down.

3. Push motor out.

4. Tighten the depth collar screw.

TO DEPLOY THE MOTOR

Loosen the Dept Collar screw, then push ﬁ rmly down on the Deploy-Assist Lever to release the collar and slide the motor

forward, out from the ramp. Lower the motor to the desired depth. Make sure it clicks into a secure, vertical position.

TO STOW THE MOTOR

Push down on the Tilt Lock Lever and raise the motor by pulling up on the composite shaft or control head. Pull the motor toward

the stern until it rests securely on the ramp and the Deploy-Assist Lever captures the latch collar. Slide the depth collar down and

secure it against the top of the steering housing to secure the motor in place and prevent accidental deployment.

TRANSPORTATION

In conditions where the stowed motor is subject to high levels of shock or vibration, take care to provide a secure stow. Move the

depth collar snug against the steering motor and tighten.

TO ADJUST THE LATCH COLLAR

The latch collar is adjustable. If needed, loosen the Phillips head screw and rotate the collar up or down to re-align the latch and

collar. The ideal adjustment is a slightly loose ﬁ t that completely captures the collar.

Tilt Lock Lever

Depth Collar Deploy-Assist Lever

Latch Collar

USING & ADJUSTING THE MOTOR

AUTOPILOT™ CONTROLS

(ON AUTOPILOT EQUIPPED MOTORS ONLY)

The Minn Kota AutoPilot™ uses a magnetic compass and a microprocessor chip to keep the trolling motor pointed in the direction

you want to go. Each time the wind or water current moves the boat oﬀ course, the AutoPilot senses the change and steers itself

back to the original heading. The AutoPilot direction is set every time a steering change is made. To change direction, steer until

the control head points to the desired course. The AutoPilot will pull the bow of the boat around and correct automatically until

the boat is moving in the direction you chose.

1. This unit has an automatic steering shutdown for safety. In conditions where an obstruction prevents the trolling motor from

turning, or in extremely windy conditions, the automatic steering may stop. Any steering input will reset the system to normal.

ADJUSTING THE DEPTH OF THE MOTOR

When setting the depth be sure the top of the motor is submerged

at least 12” to avoid churning or agitation of surface water. The

propeller must be completely submerged.

1. With the motor deployed, ﬁ rmly grasp the composite shaft above

the mount.

2. Loosen the adjustable depth collar until the shaft slides freely.

3. Raise or lower the motor to the desired depth.

4. Turn the motor control head to the desired position.

5. Tighten adjustable depth collar to secure the motor in place.

Composite Shaft

12” Minimum Depth

Motor Mount

Adjustable Depth Collar

Motor Control Head

2. When the AutoPilot is on and the trolling motor is pulled out of the water to the stow position, the steering motor will continue

to run. Turn oﬀ the AutoPilot switch to stop the motor. If the switch is left on, the steering motor will shut oﬀ automatically

after 10 seconds. The motor should not be sored in this condition for long periods as power is still being applied to all

eletronics. Always turn the Autopilot switch oﬀ and disconnect your motor from the battery when storing your boat.

3. This unit uses a magnetic compass to detect direction of travel. The compass can be adversely aﬀ ected by magnets or large,

ferrous metal objects near (within 12” of) the trolling motor control head.

4. After steering to a new direction, there is a short delay before the direction is locked in to allow the compass to stabilize.

5. Obstructions on the propeller may cause excessive vibration of the motor head. This vibration can cause the compass to

wander and erratic steering to occur. Clear the obstruction to return the motor to normal operation.

6. When broad speed changes are made, the motor heading may change slightly. This is normal.

NOTE: Always turn the AutoPilot switch oﬀ and disconnect your motor from the battery when storing your boat.

minnkotamotors.com | 11

INSTALLING AN EXTERNAL TRANSDUCER

An external sonar transducer can be installed onto the motor as shown.

1. Transducer cables should be routed through the coil cable as

depicted in the illustration to the right.

2. Leave enough slack for proper stow and deploy.

3. Mount transducer according to transducer instructions.

Note: An external transducer is not included with your trolling motor.

Your trolling motor may be pre-installed with a Universal Sonar 2

transducer system. In this case, the transducer is integrated into the

motor unit.

For compatibility and more information on Universal Sonar 2, please

visit minnkotamotors.com/us2.

ACCESSORY RECOMMENDATIONS:

• Minn Kota Transducer Mounting Kit (MKR-15)

Leave slack

Tie Wrap

Cable

Tie Wrap

Cable

Transducer

cable

USING & ADJUSTING THE MOTOR

All the controls in the foot pedal are easy to operate by either foot or hand. A light touch is all that is necessary.

MOMENTARY

A toe touch on the momentary button turns the propeller

on. Let up and the propeller stops.

MOMENTARY/CONSTANT (MOM/CON) SWITCH

When the switch is in CON position the motor will run

continuously without keeping your foot on the pedal. Slide

the switch to momentary (MOM) to again operate the

motor with toe touch.

RIGHT/LEFT

Place your foot in the center of the steering pedal, rocking

to the right steers right. Rocking to the left steers left.

The heel of your foot can also be placed on the deck of the

boat. Using your heel to pivot on, depress and hold the

center momentary to turn the motor on or depress and hold the left or right side of the pedal to steer left or right.

NOTE: The steering system is designed to turn your motor 360°. Be careful to avoid over-wrapping the coil cord around the

composite shaft.

FORWARD/REVERSE

The propeller always turns in the forward direction. You can reverse the direction of thrust by turning the motor 180˚.

SPEED CONTROL

The speed selector is the calibrated sliding bar located on the right side of the foot pedal. The speed selector provides variable

speed control with the built in pulse modulation system. Use your hand or foot to slide the bar forward to increase speed. Draw

the bar back to decrease speed. The slider also contains a roller to aid in ﬁne speed adjustment. Slide your foot over the roller

with light down pressure to adjust speed. The motor may not start turning until the speed slider reaches speeds 1 or 2. This

depends on manufacturing tolerances and if the CoPilot accessory is installed.

NON-CARPETED BOAT USE

Enclosed with your motor are four (4) rubber bumpers. If the foot pedal is to be used primarily on non-carpeted surfaces, insert

the rubber bumpers into the keyhole slots on the underside of the pedal. Slide the bumpers into the slot until they are locked into

position.

minnkotamotors.com | 13

USING THE FOOT PEDAL

Steering

Left

Steering

Right

Momentary/Constant

Switch

Speed

Control

Momentary

On/Oﬀ

Propeller

Slot End

Drive Pin

Prop Nut

Washer

PROPELLER REPLACEMENT

TOOLS AND RESOURCES REQUIRED:

• Box End Wrench

- 1/2” for motors with 70 lbs thrust or lower.

- 9/16” for motors with 80 lbs thrust or higher.

• Screwdriver (optional)

CAUTION:

Disconnect the motor from the battery

before beginning any prop work or

maintenance.

NOTE: The propeller on your motor may diﬀ er from

the one pictured.

1. Disconnect the motor from all sources of power prior to changing the propeller.

2. Hold the propeller and loosen the prop nut with pliers or a wrench.

3. Remove the prop nut and washer. If the drive pin is sheared or broken, you will need to hold the shaft stationary with a blade

screwdriver pressed into the slot on the end of the shaft.

4. Turn the old prop to horizontal (as illustrated) and pull it straight oﬀ . If drive pin falls out, push it back in.

5. Align the new propeller with the drive pin.

6. Install the prop washer and prop nut.

7. Tighten the prop nut 1/4 turn past snug [25-35 inch lbs.] Do not over tighten as this can damage the prop.

GENERAL MAINTENANCE

1. After use, the entire motor should be rinsed with freshwater. This series of motors is not equipped for saltwater exposure.

2. The composite shaft requires periodic cleaning and lubrication for proper retraction and deployment. A coating of an aqueous

based silicone spray will improve operation.

3. The propeller must be inspected and cleaned from weeds and ﬁ shing line after every use.

Fishing line and weeds can get behind the prop, damage the seals and allow water to enter the motor.

4. Verify the prop nut is secure each time the motor is used.

5. To prevent accidental damage during transportation or storage, disconnect the battery whenever the motor is oﬀ of the water.

For prolonged storage, lightly coat all metal parts with an aqueous based silicone spray.

6. For maximum battery life recharge the battery(s) as soon as possible after use. For maximum motor performance restore

battery to full charge prior to use.

7. Keep battery terminals clean with ﬁ ne sandpaper or emery cloth.

8. The propeller is designed to provide weed free operation with very high eﬃ ciency. To maintain this top performance, the

leading edge of the blades must be kept smooth. If they are rough or nicked from use, restore to smooth by sanding with ﬁ ne

sandpaper.

SERVICE & MAINTENANCE

1. Motor fails to run or lacks power:

• Check battery connections for proper polarity.

• Make sure terminals are clean and corrosion free. Use ﬁ ne sandpaper or emery cloth to clean terminals.

• Check battery water level. Add water if needed.

2. Motor loses power after a short running time:

• Check battery charge. If low, restore to full charge.

3. You experience prop vibration during normal operation:

• Remove and rotate the prop 180°. See removal instructions in the Propeller Replacement Section.

4. Experiencing interference with your ﬁ shﬁ nder:

• You may, in some applications, experience interference in your depth ﬁ nder display. We recommend that you use a separate

deep cycle marine battery for your trolling motor and that you power the depth ﬁ nder from the starting/cranking battery. If

problems still persist, call our service department at 1-800-227-6433.

NOTE: For any other malfunctions, visit an Authorized Service Center. You can search for an Authorized Service Center in your

area by visiting our Authorized Service page, found online at minnkotamotors.com, or by calling our customer service number at

800-227-6433.

FOR FURTHER TROUBLESHOOTING AND REPAIR

We oﬀ er several options to help you troubleshoot and/or repair your product. Please read through the options listed below.

FREQUENTLY ASKED QUESTIONS

We have FAQs available on our website to help answer all of your Minn Kota questions. Visit minnkotamotors.com and click on

“Frequently Asked Questions” to ﬁ nd an answer to your question.

CALL US (FOR U.S. AND CANADA)

Our consumer service representatives are available Monday – Friday between 7:00 a.m. – 4:30 p.m. CST at 800-227-6433.

If you are calling to order parts, please have the 11-character serial number from your product, speciﬁ c part numbers, and credit

card information available. This will help expedite your call and allow us to provide you with the best consumer service possible.

You can reference the parts list located in your manual to identify the speciﬁ c part numbers.

EMAIL US

You can email our consumer service department with questions regarding your Minn Kota products. To email your question, visit

minnkotamotors.com and click on “Support”.

AUTHORIZED SERVICE CENTERS

Minn Kota has over 300 authorized service centers in the United States and Canada where you can purchase parts or get your

products repaired. Please visit our Authorized Service Center page on our website to locate a service center in your area.

minnkotamotors.com | 15

TROUBLESHOOTING & REPAIR

PARTS DIAGRAM

118

116

117

114

54 53

61a

46A

65A

60A

112

103

104

99a

108

107

105

113

109

106

110

100

101

102

This page provides Minn Kota® WEEE compliance disassembly

instructions. For more information about where you should

dispose of your waste equipment for recycling and recovery and/

or your European Union member state requirements, please

contact your dealer or distributor from which your product was

purchased.

Tools required, but not limited to: ﬂ at head screw driver, Phillips

screw driver, socket set, pliers, wire cutters.

POWERDRIVE 45

45 LBS THRU - 12 VOLT - 48” SHA

2314966 rev H ECN 36330 3/15

minnkotamotors.com | 17

PARTS LIST

POWERDRIVE 45

45 LBS THRU - 12 VOLT - 48” SHA

ITEM QTY PART

NUMBER DESCRIPTION

1 1 2-100-204 ARMATURE  SEMBLY 12V VARS TXT

2 1 140-010 BALL BEARING

3 1 788-015 R AINING RING

4 1 2-200-079 HOUSING  SEMBLY CENTER 3.25 TXT

5 1 421-132 HOUSING BRUSH END 3.25 TXT

6 1 2-400-187 P IN END HOUSING  SEMBLY 3.25

7 1 144-049 BEARING - F NGE (SERVICE ONLY)

8 1 880-003 SEAL

9 1 880-006 SEAL WITH SHIELD

10 2188-052 BRUSH  SEMBLY

12 1738-030 BRUSH P TE W/HOLDER

13 2975-032 SPRING - COMPR SION

14 1701-041 O-RING

15 2701-007 O-RING, THRU-BOLT

16 1701-039 O-RING

17 2830-001 SCREW-8-32

18 2830-078 THRU BOLT 8-32 X 8.96

19 1990-067 W HER-  EEL THRU

20 2990-070 W HER - NY TRON

21 12069283 MOTOR  SEMBLY 12V 3.25 48”

25 12032075 TUBE- RBON COMPOSITE 48”

n11378121 PROPELLER KIT

26 12061122 PROPELLER

27 12151726 W HER-5/16 SS

28 12053101 NUT-PROP NYLOC

29 12092600 PIN-DRIVE

30 12301545 COL R-  TCH PD/AP

31 12303434 SCREW- 8-32X5/8 MACH PHCR

32 12303112 NUT 8-32 NYLOC SS

33 12301936 EXTRUSION- B E MACHINED

34 12303930 MOTOR R - RIGHT 3-1/4

35 12303935 MOTOR R - LE 3-1/4

36 42303430 SCREW 1/4-20X5/8 SELF TAP

37 12771826 DRIVE HOUSING /  TCH HANDLE  SY

n12882011 BUSHING/ OUTSHA KIT (INCLUD 39-42)

*39 12302010 DRIVE HOUSING OUTPUT SHA

*40 22307304 BUSHING- INNER

*41 22307305 BUSHING- OUTER

*42 12304603 O-RING

43 12307050 MOTOR- DRIVE HOUSING HIGH SPD

44 12307201  TCH HANDLE PD/AP

45 12302750 SPRING-  TCH TORSION PD/AP

46 12302627 PIN- ROLL ZINC

46A 62303407 SCREW - DRIVE HOUSING

47 12305564 DE L- OW/DEPLOY

48 42305110 PAD-PIVOT SUPT

49 22305103 PIVOT PAD- NEW MTR’L

50 12300500 PIN- TCH

51 12300510 PIN-PIVOT

52 42013100 NUT-SPEED

53 12303612 ROD-RELE E RT/AP S

54 12322700 SPRING-RELE E LEVER

55 12303710 LEVER-RELE E

56 12300101 RELE E-KNOB

57 12301700 SPACER-RELE E LEVER

58 12303430 SCREW-1/4-20 X 5/8

59 12031522 COL R- DRIVE (W/INSERT)

60 12011365 SCREW-COL R/NEW KNOB

60A 12323104 NUT

61 12304064 CONTROL BOARD  SEMBLY- 12V PD

61A 12320208 DU PLUG

ITEM QTY PART

NUMBER DESCRIPTION

62 12355410 SHRINK TUBE-3/8 ODX2

64 32303434 SCREW-8-32 X 5/8

65 12090651 LEADWIRE LOGA 44”

65A 12307310 BEAD - FERRITE (CE MODE ONLY)

66 22020700 TERMINAL RING

67 12321310  RAIN RELIEF- BRACK PD/AP

68 12323405 SCREW-1/4-20 X 5/8

69 12306555 HOUSING- CENTER PD/AP

70 12074070 BATTERY GAUGE - 12 V

71 12316605 DE L, BATTERY GAUGE

72 12302935  RAIN RELIEF-DR. HOUSING

73 12303960 SIDEP TE (RIGHT)PD MK

74 12303965 SIDEP TE(LE )PD MK

75 42303430 SCREW-1/4-20 X 5/8

76 12302515 CONTROL BOX PD/AP

77 12991280 COIL CORD W RAIN RELIEF 48, 54”

12991282 COIL CORD W RAIN RELIEF 60”

78 32065400 WIRE INSU TOR-LGE

79 12256300 TIE WRAP-5” B CK

80 12224702 INSERT- PLUG

12224700 INSERT- PLUG US2

82 12033400 SCREW-10-24 X 1-3/4 PPH Z/P

83 12013110 NUT-HEX 10-24 ZCP

86 12300237 CONTROL BOX COVER

89 12315692 DE L- COVER 45PD

90 42012100 SCREW-8-18 X 5/8

n12994725 FOOT PEDAL  SEMBLY

91 12304505 FOOT PEDAL B E

92 12308501 WEAR P TE FOOT PDL

93 12300255 FOOT PEDAL, CORDED UPPER

94 12303723 BUTTON, MOMENTARY

95 12303722 BUTTON, MOM/CON

96 32302730 SPRING-LONG-UPPER PEDAL

98 2302732 SPRING-LOWER PEDAL

99 12304052 CONTROL BOARD  SEMBLY- PDL

99A 12320207 DU  P

100 12308620 SLIDER, SPEED

101 12308409 MAGN , 1/4 X 1/4

102 12778408 MAGN , 1/4 X 1/8

103 12300252 COVER, SPEED SELE OR

104 12308606 SWITCH, DOUBLE FINGER

105 12308608 SWITCH, SINGLE FINGER

106 12307900 WHEEL, SPEED

107 12308625 SLIDER,  EERING

108 92302100 SCREW-6-20 X 1/2

109 42372103 SCREW-6.20 X 3/8

110 12316600 DE L, ON/OFF SWITCH

112 12994859 BAG  SEMBLY- 4 RUBBER BUMPERS

113 12302907  RN RLF PD FP

n12994864 BAG  SEMBLY- (BOLT,NUT,W HERS)

*114 62263462 BOLT-MOUNTING-1/4X2 W/ G

*116 62261713 W HER-1/4

*117 62263103 NUT NYLOK 1/4-20 MTG

*118 62301720 W HER-MOUNTING RUBBER

n12883460 SEAL & ORING KIT

n THIS ITEM IS PART OF AN  SEMBLY.

*THIS ITEM IS PART OF A KIT AND ONLY LI ED FOR

VIEWING PURPOS .

ENVIRONMENTAL COMPLIANCE STATEMENT:

It is the intention of JOME to be a responsible corporate citizen, operating in compliance with known and applicable

environmental regulations, and a good neighbor in the communities where we make or sell our products.

WEEE DIRECTIVE:

EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors, sellers,

and manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer

electronics to take responsibility for the management of waste from their products to achieve environmentally responsible

disposal during the product life cycle.

WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be required

for EEE designed and intended as ﬁ xed or temporary installation in transportation vehicles such as

automobiles, aircraft, and boats. In some European Union member states, these vehicles are considered

outside of the scope of the Directive, and EEE for those applications can be considered excluded from the

WEEE Directive requirement.

This symbol (WEEE wheelie bin) on product indicates the product must not be disposed of with other

household refuse. It must be disposed of and collected for recycling and recovery of waste EEE. Johnson

Outdoors Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal to comply

in the collection, treatment, recovery, and environmentally sound disposal of those products; however, these requirement do

vary within European Union member states. For more information about where you should dispose of your waste equipment for

recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from

which your product was purchased.

DISPOSAL:

Minn Kota motors are not subject to the disposal regulations EAG-VO (electric devices directive) that implements the WEEE

directive. Nevertheless never dispose of your Minn Kota motor in a garbage bin but at the proper place of collection of your local

town council.

Never dispose of battery in a garbage bin. Comply with the disposal directions of the manufacturer or his representative and

dispose of them at the proper place of collection of your local town council.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects

or other reproductive harm.

COMPLIANCE STATEMENTS

minnkotamotors.com | 19

NOTES

Minn Kota Consumer & Technical Service

Johnson Outdoors Marine Electronics, Inc.

PO Box 8129

Mankato, MN 56001

121 Power Drive

Mankato, MN 56001

Phone (800) 227-6433

Fax (800) 527-4464

minnkotamotors.com

For a complete listing of Minn Kota accessories, visit minnkotamotors.com

• 60-Amp Circuit Breaker

• Mounting Brackets

• Stabilizer Kits

• Extension Handles

• Battery Connectors

• Battery Boxes

• Quick Connect Plugs

RECOMMENDED ACCESSORIES

ON-BOARD & PORTABLE BATTERY CHARGERS

Stop buying new batteries and start taking care of the ones you’ve got. Many chargers can actually damage your battery

over time – creating shorter run times and shorter overall life. Digitally controlled Minn Kota chargers are designed to provide the

fastest charge that protect and extend battery life.

TALON SHALLOW WATER ANCHOR

Talon deploys faster, holds stronger and runs quieter than any other shallow water anchor. Available in depths up to 12’ and bold color

options including camo, it boasts an arsenal of features and innovations that no other anchor can touch:

MINN KOTA ACCESSORIES

We offer a wide variety of trolling motor accessories, including:

MK210DMK345PC MK110P

• Vertical, Multi-Stage Deployment

• User-Selectable Anchoring Modes

• 2x Anchoring Force

• Fast Deploy

• Auto Up/Down

• Triple Debris Shields

• Built-In Wave Absorption

• Noise Dissipation

• Versatile Adjustments

Part #2317112 Rev N 6/15

ECN 36427

La page est en cours de chargement...

MINN KOTA PowerDrive V2 Bow-Mount Trolling Motor Manuel utilisateur

Marque: MINN KOTA

Modèle: PowerDrive V2 Bow-Mount Trolling Motor

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: MINN KOTA PowerDrive V2 Bow-Mount Trolling Motor User manual

MINN KOTA PowerDrive V2 Bow-Mount Trolling Motor Manuel utilisateur

MINN KOTA PowerDrive V2 Bow-Mount Trolling Motor Manuel utilisateur

dans d''autres langues

Documents connexes