sunjoe 24V-150WI-CT Manuel utilisateur

Marque: sunjoe

Modèle: 24V-150WI-CT

Catégorie: Chargeurs de batterie

Taper: Manuel utilisateur

A Division of Snow Joe®, LLC

OPERATOR’S MANUAL

Model 24V-150WI-CT Form No. SJ-24V-150WI-CT-880E-M

PORTABLE POWER

INVERTER – TOOL ONLY

24V MAX* | 150 WATTS

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Read all safety warnings and instructions. Failure to follow the

warnings and instructions may result in electric shock, re and/

or serious injury.

General Safety WARNINGS!

Notice the personal safety alert symbol m used in this manual

to draw your attention to a WARNING given along with the

particular operating instruction. This means that the operation

requires special ATTENTION, CAUTION, and AWARENESS.

This product’s AC receptacle has a non-sinusoidal output and

is not recommended for use with certain types of sensitive

electronics. Please refer to your product Operator’s Manual.

mWARNING! This power inverter is only for use with

Snow Joe® + Sun Joe® iON+ 24V series batteries and

chargers.

1. Do not expose the power inverter to rain or wet

conditions. Water entering the power inverter will increase

the risk of electric shock.

2. Do not use the power inverter if it has been dropped or

received a sharp blow. A damaged power source will

increase the risk of re.

3. Remove the battery pack from the power inverter when

not in use.

4. This product is for indoor use only.

5. Do not disassemble the power inverter.

6. To reduce the risk of injury, close supervision is necessary

when an appliance is used near children.

7. Store the power inverter indoors and away from children.

8. Use caution when connecting/disconnecting devices to

this unit. Do not force plugs into this unit.

9. Do not overload the power inverter. It must be used for

powering devices less than the product rating.

10. Two- or three-prong plugs may be used with this

product. Do not force a polarized plug (one prong larger

than the other) into this product. Flip plug over and retry.

11. Never block air vents. Blocked vents may cause

overheating. Power inverter will automatically shut o

when overheated.

12. Keep power inverter cool. Do not place near heat vents or

in direct sunlight.

13. Do not use the power inverter around ammable fumes

and gasses, such as in the bilge of a boat or near propane

tanks.

14. Do not put foreign objects into the inverter.

15. Operate this product using only the AC power type listed

in the product specications.

16. This unit should never be hard wired into a circuit.

17. Do not power life support devices or other necessary

medical equipment with this inverter.

Battery & Charger

Safety Instructions

NOTE: This unit is tool only. The battery and the charger are

not included. They must be purchased separately.

Model 24V-150WI-CT is compatible with the iON+ 24V System

batteries and chargers. See page 11 for more information.

We pay a great deal of attention to the design of every battery

pack to ensure that we supply you with batteries that are safe,

durable and have a high energy density. The battery cells have

a wide range of safety devices. Each individual cell is initially

formatted and its electrical characteristic curves are recorded.

This data is then used exclusively to be able to assemble the

best possible battery packs.

Despite all the safety precautions, caution must always be

exercised when handling batteries. The following points must

be obeyed at all times to ensure safe use. Safe use can only

be guaranteed if undamaged cells are used. Incorrect handling

of the battery pack can cause cell damage.

IMPORTANT! Analyses conrm that incorrect use and poor

care of high-performance batteries are the main factors

responsible for personal and/or product damage.

mWARNING! Use only approved replacement batteries;

other batteries may damage the power tool and cause it to

malfunction, which can lead to serious personal injury.

mWARNING! Do not use a battery pack or appliance that

is damaged or modied. Damaged or modied batteries may

exhibit unpredictable behavior resulting in re, explosion or risk

of injury.

Do not modify or attempt to repair the appliance or the battery

pack except as indicated in the instructions for use and care.

Have your battery pack serviced by a qualied repair person

using only identical replacement parts. This will ensure that the

safety of the battery pack is maintained.

mCAUTION! To reduce the risk of injury, charge the

Sun Joe® 24V lithium-ion battery pack only in its designated

Sun Joe® lithium-ion charger. Other types of chargers present

risk of re, personal injury and damage. Do not wire a battery

pack to a power supply plug or car cigarette lighter. Such

misuse will permanently disable or damage the battery pack.

• Avoid dangerous environments – Do not charge the

battery pack in rain, snow or in damp or wet locations.

Do not use the battery pack or charger in the presence of

explosive atmospheres (gaseous fumes, dust or ammable

materials) because sparks may be generated when inserting

or removing the battery pack, which could lead to a re.

• Charge in a well-ventilated area – Do not block the

charger vents. Keep them clear to allow for proper

ventilation. Do not allow smoking or open ames near a

charging battery pack. Vented gases may explode.

NOTE: The safe temperature range for the battery is 41°F –

105ºF (5°C – 40.5°C). Do not charge the battery outside in

freezing weather; charge it at room temperature.

• Maintain charger cord – When unplugging the charger, pull

the plug, not the cord, from the receptacle to reduce the

risk of damage to the electrical plug and cord. Never carry

the charger by its cord or yank it by the cord to disconnect

it from the receptacle. Keep the cord away from heat, oil

and sharp edges. Make sure the cord will not be stepped

on, tripped over or subjected to damage or stress when the

charger is in use. Do not use the charger with a damaged

cord or plug. Replace a damaged charger immediately.

• Do not use an extension cord unless it is absolutely

necessary – Using the wrong, damaged or improperly

wired extension cord poses a risk of re and electric shock.

If an extension cord must be used, plug the charger into a

properly wired 16 gauge or larger extension cord with the

female plug matching the male plug on the charger. Make

sure that the extension cord is in good electrical condition.

• Use only recommended attachments – Use of an

attachment not recommended or sold by the battery

charger or battery pack manufacturer may result in risk of

re, electric shock or personal injury.

• Unplug charger when not in use – Make sure to

disconnect battery pack from unplugged charger.

mWARNING! To reduce the risk of electric shock,

always unplug the charger before performing any cleaning

or maintenance. Do not allow water to ow into the charger.

Use a Ground Fault Circuit Interrupter (GFCI) to reduce shock

hazards.

• Do not burn or incinerate battery pack – Battery pack

may explode, causing personal injury or damage. Toxic

fumes and materials are created when battery packs are

burned.

• Do not crush, drop or damage battery pack – Do not use

the battery pack or charger if they have sustained a sharp

blow, been dropped, run over or have been damaged in any

way (i.e. pierced with a nail, hit with a hammer, stepped on,

etc.).

• Do not disassemble – Incorrect reassembly may pose

a serious risk of electric shock, re or exposure to toxic

battery chemicals. If the battery or charger are damaged,

contact an authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563) for assistance.

• Battery chemicals cause serious burns – Never let a

damaged battery pack contact the skin, eyes or mouth.

If a damaged battery pack leaks battery chemicals, use

rubber or neoprene gloves to safely dispose of it. If skin

is exposed to battery uids, wash the aected area with

soap and water and rinse with vinegar. If eyes are exposed

to battery chemicals, immediately ush with water for 20

minutes and seek medical attention. Remove and dispose

of contaminated clothing.

• Do not short circuit – When battery pack is not in use,

keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects

that can make a connection from one terminal to another.

Shorting the battery terminals together may cause burns or

a re.

• Store your battery pack and charger in a cool, dry

place – Do not store the battery pack or charger where

temperatures may exceed 105ºF (40.5ºC), such as in direct

sunlight or inside a vehicle or metal building during the

summer.

Information about the battery

1. For optimum battery performance, avoid low discharge

cycles by charging the battery pack frequently.

2. Store the battery pack in a cool place, ideally at 77°F

(25°C) and charged to at least 40%.

3. Lithium-ion batteries are subject to a natural aging

process. The battery pack must be replaced at the latest

when its capacity falls to just 80% of its capacity when

new. Weakened cells in an aged battery pack are no

longer capable of meeting the high power requirements

needed for the proper operation of your power inverter,

and therefore pose a safety risk.

4. Do not throw the battery pack into an open re as this

poses a risk of explosion.

5. Do not ignite the battery pack or expose it to re.

6. Do not exhaustively discharge batteries. Exhaustive

discharge will damage the battery cells. The most

common cause of exhaustive discharge is lengthy storage

or non-use of partially discharged batteries. Stop working

as soon as the performance of the battery falls noticeably

or the electronic protection system triggers. Place the

battery pack in storage only after it has been fully charged.

7. Protect the battery and the tool from overloads. Overloads

will quickly result in overheating and cell damage inside

the battery housing even if this overheating is not

apparent externally.

8. Avoid damage and shocks. Immediately replace batteries

that have been dropped from a height of more than

3 feet (1 meter) or those that have been exposed to violent

shocks, even if the housing of the battery pack appears to

be undamaged. The battery cells inside the battery may

have suered serious damage. In such instances, please

read the waste disposal information for proper battery

disposal.

9. If the battery pack suers overloading and overheating,

the integrated protective cuto will switch o the

equipment for safety reasons.

IMPORTANT! Do not press the power supply button any

more if the protective cut-o has been activated. This may

damage the battery pack.

10. Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of re when used with

another battery pack.

11. Use appliances only with specically designated battery

packs. Use of any other battery packs may create a risk of

injury and re.

12. Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

13. Do not use a battery pack or appliance that is damaged

or modied. Damaged or modied batteries may exhibit

unpredictable behavior resulting in re, explosion or risk of

injury.

14. Do not expose a battery pack or appliance to re or

excessive temperature. Exposure to re or temperature

above 265ºF (130°C) may cause explosion.

15. Follow all charging instructions and do not charge the

battery pack or appliance outside of the temperature

range specied in the instructions. Charging improperly

or at temperatures outside of the specied range may

damage the battery and increase the risk of re.

Information about the charger and the

charging process

1. Please check the data marked on the rating plate of the

battery charger. Be sure to connect the battery charger

to a power supply with the voltage marked on the rating

plate. Never connect it to a dierent mains voltage.

2. Protect the battery charger and its cord from damage.

Keep the charger and its cord away from heat, oil and

sharp edges. Have damaged cords repaired without delay

by a qualied technician at an authorized Snow Joe® +

Sun Joe® dealer or call the Snow Joe® + Sun Joe®

customer service center at 1-866-SNOWJOE

(1-866-766-9563).

3. Electrical plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

grounded appliances. Unmodied plugs and matching

outlets will reduce the risk of electric shock.

4. Keep the battery charger, battery pack and the power

inverter out of the reach of children.

5. During periods of heavy use, the battery pack will become

warm. Allow the battery pack to cool to room temperature

before connecting with the charger to recharge.

6. Do not overcharge batteries. Do not exceed the maximum

charging times. These charging times only apply to

discharged batteries. Frequent insertion of a charged or

partially charged battery pack will result in overcharging

and cell damage. Do not leave batteries in the charger for

days on end.

7. Never use or charge the battery if you suspect that it has

been more than 12 months since the last time they were

charged. There is a high probability that the battery pack

has already suered dangerous damage (exhaustive

discharge).

8. Charging batteries at a temperature below 41°F (5°C) will

cause chemical damage to the cells and may cause a re.

9. Do not use batteries that have been exposed to heat

during the charging process, as the battery cells may have

suered dangerous damage.

10. Do not use batteries that have suered curvature or

deformation during the charging process or those that

exhibit other atypical symptoms (gassing, hissing,

cracking, etc.).

11. Never fully discharge the battery pack (maximum

recommended depth of discharge is 80%). A complete

discharge of the battery pack will lead to premature aging

of the battery cells.

Protection from environmental inuences

1. Protect your power inverter and the battery charger from

moisture and rain. Moisture and rain can cause dangerous

cell damage.

2. Do not use the power inverter or the battery charger near

vapors and ammable liquids.

3. Use the battery charger and power inverter only in dry

conditions and at an ambient temperature of 41ºF – 105°F

(5°C – 40.5°C).

4. Do not keep the battery charger in places where the

temperature is liable to reach over 105°F (40.5°C). In

particular, do not leave the battery charger in a car that is

parked in the sunshine.

5. Protect batteries from overheating. Overloads,

overcharging and exposure to direct sunlight will result

in overheating and cell damage. Never charge or work

with batteries that have been overheated – replace them

immediately, if possible.

6. Store the charger and your power inverter only in dry

locations with an ambient temperature of 41ºF – 105°F

(5°C – 40.5°C). Store your lithium-ion battery pack in a

cool, dry place at a temperature of 77°F (25°C). Protect the

battery pack, charger and power inverter from humidity

and direct sunlight. Only place fully charged batteries in

storage (charged to at least 40%).

7. Prevent the lithium-ion battery pack from freezing. Battery

packs that were stored below 32°F (0°C) for more than 60

minutes must be discarded.

8. When handling batteries, be wary of electrostatic charge.

Electrostatic discharges can damage the electronic

protection system and the battery cells. Avoid electrostatic

charging and never touch the battery poles.

Safety Symbols

The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all

instructions on the machine before attempting to assemble and operate.

READ THE OPERATOR'S

MANUAL(S) – Read, understand,

and follow all instructions in the

user manual(s) before attempting

to assemble and operate.

SAFETY ALERT – Indicates a

precaution, a warning, or a danger.

Indoor use only.

WARNING! Do not expose the

unit to rain or wet conditions.

Keep dry.

WARNING! Electrical shock hazard.

Symbols SymbolsDescriptions Descriptions

Know Your Portable Power Inverter

Read the owner’s manual and safety instructions carefully before operating this portable power inverter. Compare the illustration

below to the portable power inverter in order to familiarize yourself with the location of the various controls and adjustments.

Save this manual for future reference.

1. Light On/O switch

2. Power button

(status indicator LED)

3. USB-C receptacle

4. USB-A receptacle

5. AC receptacle

6. LED light

7. Battery compartment

FRONT BACK

4567

SOLD SEPARATELY | Battery + Charger options available at sunjoe.com

24VBAT-LT 24VBAT-XR 24VCHRG-QC 24VCHRG-DPC24VBAT24VBAT-LTE

Technical Data

Output Power ............................................... 150 W continuous

Surge Power ............................................................. 300 W/2 s

DC Input | Battery Voltage Max* ................................. 24V D.C.

AC Output Voltage ...................................... 120 V A.C. | 1.25 A

USB Output Voltage ................ USB-A: 5 V/9 V/12 V, up to 3 A

USB-C: 5 V/9 V/12 V/15 V, up to 3 A

Output Wave Form ............................................ Modied wave

LED light ............................................................................. 1 W

Net Weight .......................................................... 0.6 lbs (270 g)

*Initial no-load voltage, when fully charged, peaks at 24 volts; nominal voltage

under typical load is 21.6 volts.

Unpacking

Carton Contents

• Portable power inverter

• Manual with registration card

1. Carefully remove the portable power inverter and check to

see that all of the above items are supplied.

2. Inspect the product carefully to make sure no breakage or

damage occurred during shipping. If you nd damaged or

missing parts, DO NOT return the unit to the store. Please

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

NOTE: Do not discard the shipping carton and packaging

material until you are ready to use your new portable

power inverter. The packaging is made of recyclable

materials. Properly dispose of these materials in

accordance with local regulations.

IMPORTANT! The equipment and packaging material are not

toys. Do not let children play with plastic bags, foils or small

parts. These items can be swallowed and pose a suocation

risk!

Battery Pack Operation

The equipment is powered by a lithium-ion battery. The battery

pack is completely sealed and maintenance free.

In order to operate this portable power inverter you will

need a iON+ 24V System battery and charger. For optimal

performance of this unit, it is recommended to use the

4.0 Ah battery (24VBAT) or greater. See page 11 for battery

and charger options and specications, or for more

information visit sunjoe.com.

TOOL ONLY

BATTERY + CHARGER SOLD SEPARATELY

Battery Charge Level Indicator

The battery pack is equipped with a push button for checking

the charge level. Simply press the push button to read o the

battery charge level from the LEDs of the battery indicator:

• All 3 level monitoring LEDs are lit: Battery charge level

is high.

• 2 level monitoring LEDs are lit: Battery charge level

is decreasing. Turn o the power inverter as soon as

possible.

• 1 level monitoring LED is lit: Battery is at. Turn o the

power inverter IMMEDIATELY and charge the battery.

Otherwise the battery’s service life will be greatly

shortened.

NOTE: If the charge level button does not appear to be

working, insert the charger and charge as needed.

NOTE: Immediately after using the battery pack, the charge

level button may display a lower charge than it will if checked

a few minutes later. The battery cells “recover” some of their

charge after resting.

Charger Operation

mWARNING! Charge only Sun Joe® 24V lithium-ion

battery packs with the compatible Sun Joe® 24V lithium-ion

chargers. Other types of batteries may cause personal injury

and damage.

To reduce the risk of electric shock, do not allow water to ow

into the charger's AC/DC plug.

In order to operate this portable power inverter you will

need a iON+ 24V System battery and charger. For optimal

performance of this unit, it is recommended to use the

4.0 Ah battery (24VBAT) or greater. See page 11 for battery

and charger options and specications, or for more

information visit sunjoe.com.

TOOL ONLY

BATTERY + CHARGER SOLD SEPARATELY

Charge level button

The battery is at 30% capacity

and requires charging

The battery is at 60% capacity

and requires charging soon

The battery is at full capacity

Light IndicatorsLights

When to Charge the iON+ 24V Lithium-

iON Battery

NOTE: The iON+ 24V lithium-iON battery pack does not

develop a "memory" when charged after only a partial

discharge. Therefore, it is not necessary to run down the

battery pack before inserting the charger plug.

• Use the battery indicator lights to determine when to charge

your iON+ 24V lithium-iON battery pack.

• You can "top-o" your battery pack's charge before starting

a big job or after a long day of use.

Charging the Battery

1. Push the push lock buttons on the battery to pull the

battery pack out from the battery compartment (Fig. 1).

2. Depending on your Snow Joe® + Sun Joe® charger model,

how to recharge your lithium-ion battery will vary. You

may either insert your 24-volt battery into the 24VCHRG-

QC Quick Charger (sold separately) or the 24VCHRG-

DPC Dual Port Charger (sold separately) (Figs. 2 – 3).

3. The battery indicator LEDs will illuminate one by one

during the charging process. Unplug the charger

immediately when the 3 LEDs are all illuminated.

4. The 24VCHRG-QC Quick Charger (sold separately) and

the 24VCHRG-DPC Dual Port Charger (sold separately)

are also equipped with additional charging indicating

lights which will indicate the charging status (Figs. 2 – 3).

mCAUTION! FIRE HAZARD. When disconnecting the

charger from the battery, be sure to unplug the charger from

the outlet rst, then disconnect the charger from the battery.

mWARNING! This charger does not automatically

turn o when the battery is fully charged. Please take care

not to leave the battery plugged into the charger. Switch

o or unplug the charger at the mains when charging is

complete.

5. Timely recharging of the battery will help prolong the

battery's life. You must recharge the battery pack when

you notice a drop in the power.

IMPORTANT! Never allow the battery pack to become fully

discharged as this will cause irreversible damage to the

battery.

6. When charging is complete, remove the battery from the

charger by pulling the push lock buttons and sliding the

battery backward to unlock it from the charger.

Operation

When a battery pack is installed, this power inverter converts

DC electricity to 120V AC household power and/or multi-

voltage DC USB charging power, allowing the user to charge

and power a variety of devices.

mWARNING! Risk of electric shock. When using a

grounded appliance this tool will not provide an electrical path

to earth ground. Do not power devices with damaged or frayed

power cords.

Fig. 1

Battery pack

Battery lock button

Fig. 2 Battery pack

24VCHRG-QC

quick charger

(Sold separately)

red

Charging

green

Fully

Charged

Fig. 3 Battery pack

24VCHRG-DPC

dual port charger

(Sold separately)

red

Charging

green

Fully

Charged

Intended Usage

This power inverter is used for supplying electrical power for

operating compatible small electronics and USB-powered

devices such as cell phones, tablets, laptops, LED lights,

small fans, radios, etc. This device is not compatible for use

with appliances, power tools, air conditioners, sump pumps,

compressors, and/or other larger electrical devices.

Starting and Stopping

1. Slide the battery in the battery compartment. Push to

make sure it is locked in place (Fig. 4).

2. Press the power button (status indicator LED) to turn the

inverter on. The button will light up green when ready to

use (Fig. 5).

3. Plug the devices you want to power or charge into the

inverter’s USB ports and/or 120 volt AC receptacle (Fig. 6).

4. When nished, disconnect your devices and press the

On/O switch (status indicator LED) again to turn o the

power inverter. Remove the battery before storage.

Status Indicator LED

The power button is equipped with a LED light which serves as

a status indicator. Check below for dierent status indicated

by the LED.

• Solid Green Light – The inverter is in normal operating

condition.

• Blinking Green Light – The battery power is dropping.

Stop the inverter and charge the battery as soon as

possible.

• Solid Red Light – The battery is at. Check the battery

charge level with the battery charge level indicator. Charge

the battery as needed. If the situation continues, there's

something wrong with the battery. Change the battery and

try again.

• Blinking Red Light – The inverter may be overloaded

or overheated. Turn o the inverter, disconnect all the

devices and wait for the inverter to cool down. Make

sure the battery pack is suciently charged to power the

devices, then press the power button to reset the inverter.

Reconnect the devices and try again. If the fault condition

immediately reoccurs, the current load exceeds the

capacity of the inverter.

If any other situation happened, Please call the Snow Joe® +

Sun Joe® customer service center at 1-866-SNOWJOE

(1-866-766-9563).

Using the LED light

1. Slide the battery in the battery compartment. Push to

make sure it is locked in place (Fig. 3).

2. Press the power button (status indicator LED) to turn the

inverter on. The button will light up green when ready to

use.

3. Press the light On/O switch to turn on the LED light.

Press it again to turn o the LED light (Fig. 7).

Fig. 4

Battery pack

Fig. 5 Power button (status

indicator LED)

Fig. 6

Fig. 7 Light On/O switch

Maintenance

mWARNING! Always switch the product o and remove

the battery before performing inspection, maintenance, and

cleaning work.

mWARNING! When servicing, use only identical

replacement parts. Use of any other parts could create a

hazard or cause product damage.

General Maintenance

Avoid using solvents when cleaning plastic parts. Most plastics

are susceptible to damage from various types of commercial

solvents and may be damaged by their use.

mWARNING! Do not at any time let brake uids,

gasoline, petroleum-based products, penetrating oils, etc.,

come in contact with plastic parts. Chemicals can damage,

weaken or destroy plastic, which could result in serious

personal injury.

Storage

• Switch o the inverter, disconnect all appliances, remove

the battery. Thoroughly clean the housing with a soft, dry

cloth.

• Store the inverter indoors in a safe location out of the reach

of children. Keep away from corrosive agents, such as

garden chemicals and de-icing salt.

Disposal

Recycling the tool

• Do not dispose of electrical appliances as unsorted

municipal waste. Use separate collection facilities.

• Contact your local government agency for information

regarding the collection systems available.

• If electrical appliances are disposed of in landlls

or dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging your

health and well-being.

• When replacing old appliances with new ones, the retailer

is legally obligated to take back your old appliance for

disposal at least free of charge.

Recycling + Disposal

The product comes in a package that protects it against

damage during shipping. Keep the package until you are

sure that all parts have been delivered and the product is

functioning properly. Recycle the package afterwards or keep

it for long-term storage.

WEEE symbol. Waste electrical products should not

be disposed of with household waste. Please recycle

where facilities exist. Check with your local authority

or local store for recycling regulations.

Battery Caution + Disposal

Always dispose of your battery pack according to federal,

state, and local regulations. Contact a recycling agency in your

area for recycling locations.

mCAUTION! Even discharged battery packs contain

some energy. Before disposing, use electrical tape to cover

the terminals to prevent the battery pack from shorting, which

could cause a re or explosion.

mWARNING! To reduce the risk of injury or explosion,

never burn or incinerate a battery pack even if it is damaged,

dead or completely discharged. When burned, toxic fumes and

materials are emitted into the surrounding atmosphere.

1. Batteries vary according to device. Consult your manual

for specic information.

2. Install only new batteries of the same type in your product

(where applicable).

3. Failure to insert the battery in the correct polarity, as

indicated in the battery compartment or manual, may

shorten the life of the batteries or cause batteries to leak.

4. Do not mix old and new batteries.

5. Do not mix Alkaline, Standard (Carbon-Zinc) or

Rechargeable (Nickel Cadmium, Nickel Metal Hydride, or

Lithium-Ion) batteries.

6. Do not dispose of batteries in re.

7. Batteries should be recycled or disposed of as per state

and local guidelines.

Service + Support

If your Sun Joe® portable power inverter needs service or

maintenance, please call the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563).

Model + Serial Numbers

When contacting the company or reordering parts, you will

need to provide the model and serial numbers of your product.

These are found on the decal axed to the housing of your

portable power inverter. Copy these numbers into the space

provided below.

Record the following numbers from the housing or handle of your

new product: Model #:

2 4 V - 1 5 0 W I - C T

Serial #:

Optional Accessories

mWARNING! ALWAYS use only authorized Snow Joe® + Sun Joe® replacement parts and accessories. NEVER use

replacement parts or accessories that are not intended for use with this portable power inverter. Contact Snow Joe® + Sun Joe®

if you are unsure whether it is safe to use a particular replacement part or accessory with your portable power inverter. The use of

any other attachment or accessory can be dangerous and could cause injury or mechanical damage.

iON+ 24V lithium-ion Battery Quick Charger

iON+ 24V lithium-ion Dual-port Battery Charger

24VBAT-LTE

24VCHRG-QC

24VBAT-LT

24VBAT

24VBAT-XR

ModelAccessories Item

24V iON+ 1.3 Ah Lithium-Ion Battery 24VBAT-LTW

24V iON+ 1.5 Ah Lithium-Ion Battery 24VBAT-LTX

24V iON+ 2.0 Ah Lithium-Ion Battery

24V iON+ 2.5 Ah Lithium-Ion Battery

24V iON+ 4.0 Ah Lithium-Ion Battery

24V iON+ 5.0 Ah Lithium-Ion Battery

24VCHRG-DPC

NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such

changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563).

12 R4_01282020

SNOW JOE® + SUN JOE® CUSTOMER PROMISE

OUR WARRANTY:

Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used

for ordinary household use for a period of two years from the date of purchase by the original, end-user purchaser when purchased

from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality

of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from

unauthorized sellers. If your Product does not work or there’s an issue with a specic part that is covered by the terms of this Warranty,

Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no

charge, or (3) repair the Product. How cool is that!

This Warranty gives you speciﬁc legal rights, and you may also have other rights which vary from State to State.

PRODUCT REGISTRATION:

Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and

mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOWJOE

(1-866-766-9563), or by e-mailing us at [email protected]. Failure to register your Product will not diminish your warranty

rights. However, registering your Product will allow Snow Joe to better serve you with any of your customer service needs.

WHO CAN SEEK LIMITED WARRANTY COVERAGE:

This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.

WHAT IS NOT COVERED?

This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This Warranty also

does not apply if the Product was purchased from an unauthorized seller. This Warranty also does not cover cosmetic changes that do

not aect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased

at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).

ABOVE ALL ELSE, Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your experience as pleasant as

possible. Unfortunately, there are times when a Snow Joe®, Sun Joe®, or Aqua Joe® product (“Product”) does not work or breaks under

normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we have a Limited Warranty

(“Warranty”) for our Products.

Una división de Snow Joe®, LLC

MANUAL DEL OPERADOR

Modelo 24V-150WI-CT Forma N° SJ-24V-150WI-CT-880S-M

INVERSOR PORTÁTIL

– SOLO HERRAMIENTA

24 V MÁX.* | 150 W

¡IMPORTANTE!

Instrucciones de seguridad

Todos los operadores deberán leer

estas instrucciones antes del uso

Lea todas las advertencias de seguridad e instrucciones.

No seguir las advertencias e instrucciones puede causar un

choque eléctrico, incendio y/o lesiones personales graves.

¡ADVERTENCIAS generales de

seguridad!

Preste atención al símbolo m de alerta de seguridad personal

usado en este manual para enfocar su atención a una

ADVERTENCIA dada junto a una instrucción de operación

particular. Esto signica que la operación requiere ATENCIÓN,

PRECAUCIÓN y CAUTELA especiales.

El tomacorriente CA de este producto tiene una salida no

sinusoidal y no es recomendado para su uso con ciertos tipos

de dispositivos electrónicos sensibles. Consulte el manual del

operador de su producto.

m ¡ADVERTENCIA! Este inversor es solo para uso con

baterías y cargadores de la serie iON+ de 24 V de Snow Joe®

+ Sun Joe®.

1. No exponga el inversor a la lluvia o a entornos mojados.

El agua que entre al inversor incrementará el riesgo de un

choque eléctrico.

2. No use el inversor si se ha dejado caer o ha sido

severamente golpeado. Un inversor dañado incrementará

el peligro de un incendio.

3. Retire la batería del inversor cuando no esté siendo

usado.

4. Este producto es solo para uso en interiores.

5. No desarme el inversor.

6. Para reducir el riesgo de lesiones, es necesaria una

estricta supervisión cuando este artefacto sea usado

cerca de los niños.

7. Guarde el inversor en interiores y lejos del alcance de los

niños.

8. Tenga cuidado al conectar o desconectar dispositivos a

esta unidad. No fuerce enchufes dentro de la unidad.

9. No sobrecargue el inversor. Debe ser usado para

alimentar dispositivos con menos de la capacidad nominal

del inversor.

10. Se pueden usar enchufes de dos o tres patas con este

producto. No fuerce un enchufe polarizado (una pata más

grande que la otra) en este producto. Voltee el enchufe e

intente de nuevo.

11. Nunca bloquee los conductos de ventilación. Los

conductos de ventilación bloqueados pueden causar

sobrecalentamiento. El inversor se apagará de forma

automática si está sobrecalentado.

12. Mantenga el inversor a una temperatura fría. No lo

coloque cerca de conductos de calefacción o bajo la luz

directa del sol.

13. No use el inversor cerca de humos o gases inamables,

como en la sentina de un barco o cerca de tanques de

gas propano.

14. No coloque objetos extraños dentro del inversor.

15. Opere este producto usando solamente el tipo de

alimentación CA indicada en las especicaciones de

producto.

16. Este inversor nunca debe ser conectado de forma

permanente a un circuito.

17. No alimente con este inversor dispositivos de auxilio vital

u otros equipos médicos necesarios.

Instrucciones de seguridad

para las baterías y el

cargador

NOTA: este paquete solo trae la unidad. La batería y el

cargador no están incluidos. Deben ser adquiridos por

separado.

El modelo 24V-150WI-CT es compatible con las baterías y

cargadores del sistema iON+ de 24 V. Vea la página 26 para

más información.

Prestamos mucha atención al diseño de cada batería para

garantizar la producción de baterías seguras y durables, con

una alta densidad de energía. Las celdas de las baterías tienen

varios dispositivos de seguridad. Cada celda individual es

inicialmente formateada y sus curvas eléctricas características

son registradas. Estos datos son luego usados exclusivamente

para ensamblar las mejores baterías posibles.

Independientemente de todas las precauciones de seguridad,

se debe tener mucho cuidado al manipular las baterías.

Las siguientes instrucciones deben ser obedecidas en todo

momento para garantizar un uso seguro. Un uso seguro solo

puede ser garantizado si se usan celdas libres de daños. Una

manipulación incorrecta de las baterías puede causar daños

en sus celdas.

¡IMPORTANTE! Los análisis han conrmado que el uso

incorrecto y el cuidado deciente de baterías de alto

rendimiento son las causas principales de lesiones personales

y/o daños al producto.

m ¡ADVERTENCIA! Use solo baterías de repuesto

aprobadas. Otras baterías pueden dañar la herramienta

motorizada y provocar un desperfecto que pueda causar

lesiones personales severas.

m ¡ADVERTENCIA! No use baterías o artefactos que

hayan sido dañados o modicados. Las baterías dañadas o

modicadas pueden reaccionar impredeciblemente, causando

un incendio, explosión o lesiones personales.

No modique ni intente reparar el artefacto o la batería, a

menos que lo haga según lo indicado en las instrucciones de

uso y cuidado.

Su batería deberá ser reparada por una persona calicada

usando únicamente partes de repuesto originales. Esto

mantendrá la seguridad de la batería.

m ¡PRECAUCIÓN! Para reducir el riesgo de lesiones

personales, cargue la batería de iones de litio de 24 V Sun

Joe® únicamente con su cargador de baterías de iones de litio

Sun Joe® designado. Otros tipos de cargadores presentan

riesgos de incendio, lesiones personales y daños materiales.

No conecte una batería a un tomacorriente doméstico ni

encendedor de cigarrillos en su vehículo. Dicho uso indebido

dañará o deshabilitará permanentemente la batería.

• Evite entornos peligrosos: no cargue la batería bajo la

lluvia o nieve, ni en lugares húmedos o mojados. No use

la batería ni el cargador en atmósferas explosivas (gases,

polvo o materiales inamables) ya que al insertar o retirar la

batería se pueden generar chispas que causen un incendio.

• Cargue la batería en un área bien ventilada: no bloquee

los conductos de ventilación del cargador. Manténgalos

despejados para permitir una ventilación adecuada. No

permita que se fume o haya fuego abierto cerca de una

batería siendo cargada. Los gases presentes pueden

explotar.

NOTA: el rango seguro de temperaturas para la batería

es de 41°F (5°C) a 105°F (40.5°C). No cargue la batería

en exteriores a temperaturas congelantes. Cárguela a

temperatura ambiente en interiores.

• Cuide el cable de alimentación del cargador: al

desenchufar el cargador tire del enchufe, no del cable

de alimentación, para desconectarlo del tomacorriente

y así evitar daños al enchufe y cable. Nunca transporte

el cargador colgado de su cable, ni tire del cable para

desconectarlo del tomacorriente. Mantenga el cable

alejado del calor, grasas y bordes alados. Asegúrese de

que el cable no sea pisado, que la gente no se tropiece

con éste, ni que esté sujeto a daños o tensiones mientras

el cargador esté siendo usado. No use el cargador con un

cable o enchufe dañado. Reemplace un cargador dañado

inmediatamente.

• No use un cable de extensión a menos que sea

absolutamente necesario: usar un cable de extensión

incorrecto, dañado o conectado de forma inapropiada

puede causar un incendio o choque eléctrico. Si se

debe usar un cable de extensión, conecte el cargador a

un cable de extensión de calibre 16 (o más grueso) de

alambrado adecuado, con el enchufe macho del cargador

encajando perfectamente en el enchufe hembra del cable

de extensión. Verique que el cable de extensión esté en

buenas condiciones.

• Use solo los accesorios recomendados: el uso de un

accesorio no recomendado ni vendido por el fabricante de

la batería o cargador puede causar un choque eléctrico,

incendio o lesiones personales.

• Desenchufe el cargador cuando no esté siendo usado:

asegúrese de retirar la batería del cargador desenchufado.

m ¡ADVERTENCIA! Para reducir el riesgo de un choque

eléctrico, desenchufe siempre el cargador antes de llevar a

cabo cualquier tarea de limpieza o mantenimiento. No permita

que entre agua dentro del cargador. Use un interruptor de

circuito por falla a tierra (GFCI) para reducir el riesgo de un

choque eléctrico.

• No queme ni incinere la batería: la batería puede explotar

y causar lesiones personales o daños materiales. Cuando

las baterías son quemadas se generan sustancias y humos

tóxicos.

• No triture, deje caer ni dañe la batería: no use la batería

ni el cargador si han sido severamente golpeados, se

han dejado caer, se han aplastado o se han dañado de

cualquier forma como por ejemplo perforados con un clavo,

golpeados con un martillo, pisados, etc.

• No desarme las baterías ni el cargador: un reensamblado

incorrecto puede presentar un riesgo severo de choque

eléctrico, fuego o exposición a químicos tóxicos de la

batería. Si la batería o el cargador están dañados, contacte

a un concesionario autorizado Snow Joe® + Sun Joe® o

comuníquese con la central de servicio al cliente Snow Joe®

+ Sun Joe® llamando al 1-866-SNOWJOE (1-866-766-9563)

para obtener ayuda.

• Los químicos de las baterías causan quemaduras

severas: nunca deje que una batería dañada haga contacto

con la piel, ojos o boca. Si una batería dañada deja

escapar químicos, use guantes de hule o neopreno para

deshacerse de ella de forma segura. Si la piel es expuesta

a los químicos de la batería, lave el área afectada con jabón

y agua, y enjuague con vinagre. Si los ojos son expuestos

a los químicos, inmediatamente enjuáguelos con agua

durante 20 minutos y busque atención médica. Quítese y

deshágase de las vestimentas contaminadas.

• No cortocircuite los terminales: cuando la batería no

esté en uso, manténgala alejada de objetos metálicos

tales como monedas, sujetapapeles, clavos, tornillos,

alleres u otros objetos metálicos pequeños que puedan

causar el contacto de un terminal de la batería con el otro.

Cortocircuitar los terminales de una batería puede causar

quemaduras o un incendio.

• Guarde su batería y cargador en un lugar fresco y seco:

no guarde la batería ni el cargador donde las temperaturas

puedan exceder los 105°F (40.5°C), como bajo la luz directa

del sol o dentro de un vehículo o construcción metálica

durante el verano.

Información sobre la batería

1. Para un óptimo rendimiento de la batería, evite ciclos de

descarga baja cargándola frecuentemente.

2. Guarde la batería en un lugar fresco, de preferencia a 77°F

(25℃) y cargada al menos a un 40%.

3. Las baterías de iones de litio están sujetas a un proceso

natural de desgaste. Una batería debe ser reemplazada

a más tardar cuando su capacidad caiga a un 80% de

su capacidad inicial, cuando estaba nueva. Las celdas

debilitadas en una batería gastada no cumplirán con los

requisitos de alta potencia necesarios para la operación

adecuada de su inversor y, por tanto, representan un

riesgo de seguridad.

4. No arroje la batería al fuego abierto ya que puede causar

una explosión.

5. No queme la batería ni la exponga al fuego.

6. No descargue las baterías exhaustivamente. Una descarga

exhaustiva dañará las celdas de la batería. La causa más

común de descarga exhaustiva es el almacenamiento

prolongado o la falta de uso de baterías parcialmente

descargadas. Deje de trabajar tan pronto como el

rendimiento de la batería caiga considerablemente o se

active el sistema de protección electrónico. Almacene

la batería únicamente luego de haberla cargado por

completo.

7. Proteja la batería y la herramienta contra sobrecargas. Las

sobrecargas causarán rápidamente un sobrecalentamiento

y daños a las celdas dentro de la batería, incluso si este

sobrecalentamiento no es aparente por fuera.

8. Evite daños y golpes. Reemplace inmediatamente las

baterías que se hayan caído desde una altura de más de

3 pies (1 m) o aquellas que hayan sido expuestas a golpes

violentos, incluso si el exterior de la batería aparenta no

tener daños. Las celdas dentro de la batería pueden haber

sufrido daños severos. En dichos casos, lea la información

de eliminación para deshacerse apropiadamente de la

batería.

9. Si la batería sufre una sobrecarga y sobrecalentamiento,

el sistema interruptor de corte de protección integrado

apagará el equipo por motivos de seguridad.

¡IMPORTANTE! No presione más el botón de suministro

de alimentación si el sistema interruptor de protección se

ha activado. Esto puede dañar la batería.

10. Recargue solo con el cargador especicado por el

fabricante. Un cargador adecuado para un tipo de batería

puede causar un incendio al ser usado con una batería de

otro tipo.

11. Use artefactos a baterías solo con baterías

especícamente diseñadas para éstos. El uso de

cualquier otra batería puede causar un incendio o lesiones

personales.

12. Bajo condiciones extremas, la batería puede expulsar

un líquido. Evite el contacto con este líquido. Si usted

accidentalmente hace contacto con este líquido,

enjuáguese con agua. Si el líquido hace contacto con

los ojos, adicionalmente busque atención médica. El

líquido que sale de las baterías puede causar irritación o

quemaduras.

13. No use baterías o artefactos que hayan sido dañados o

modicados. Las baterías dañadas o modicadas pueden

reaccionar impredeciblemente, causando un incendio,

explosión o lesiones personales.

14. No exponga una batería o artefacto al fuego o a

temperaturas extremas. Una exposición al fuego o a

temperaturas por encima de los 265°F (129.5°C) puede

causar una explosión.

15. Siga todas las instrucciones de carga, y no cargue la

batería o artefacto fuera del rango de temperaturas

especicado en las instrucciones. Cargar de forma

incorrecta o a temperaturas fuera del rango especicado

puede dañar la batería e incrementar el riesgo de incendio.

Información sobre el cargador y el proceso

de carga

1. Verique la información indicada en la placa de

especicaciones del cargador de baterías. Asegúrese

de conectar el cargador de baterías a una fuente de

alimentación que tenga el voltaje indicado en su placa

de especicaciones. Nunca lo conecte a una fuente de

alimentación con un voltaje diferente al indicado.

2. Proteja el cargador de baterías y su cable contra

daños. Mantenga el cargador y su cable alejados del

calor, grasa, aceite y bordes alados. Haga reparar sin

demora los cables dañados por un técnico calicado en

un concesionario autorizado Snow Joe® + Sun Joe® o

comuníquese con la central de servicio al cliente

Snow Joe® + Sun Joe® llamando al 1-866-SNOWJOE

(1-866-766-9563).

3. Los enchufes deben encajar en los tomacorrientes.

Nunca modique el enchufe de ninguna manera. No use

ningún adaptador de enchufe con artefactos que tengan

conexión a tierra. El uso de enchufes no modicados

y tomacorrientes equivalentes reducirá el riesgo de un

choque eléctrico.

4. Mantenga el cargador de baterías, la batería y el inversor

lejos del alcance de los niños.

5. Durante periodos de trabajo pesado, la batería se

calentará. Deje que la batería se enfríe a temperatura

ambiente antes de conectarla al cargador para su recarga.

6. No sobrecargue las baterías. No exceda los tiempos

máximos de carga. Estos tiempos de carga solo se

aplican a baterías descargadas. La inserción frecuente de

una batería cargada o parcialmente cargada resultará en

una sobrecarga y daños a las celdas. No deje las baterías

en el cargador por días enteros.

7. Nunca use o cargue la batería si sospecha que han

pasado más de doce (12) meses desde la última vez que

fue cargada. Existe una alta probabilidad de que la batería

ya haya sufrido un daño severo por descarga exhaustiva.

8. Cargar baterías a temperaturas menores de 41°F (5°C)

causará daños químicos a las celdas y puede provocar un

incendio.

9. No use baterías que hayan sido expuestas al calor durante

el proceso de carga, ya que sus celdas pueden haber

sufrido daños severos.

10. No use baterías que se hayan curvado o deformado

durante el proceso de carga, ni aquellas que muestren

otros síntomas atípicos tales como liberación de gases,

zumbidos, grietas, etc.

11. Nunca descargue por completo la batería (se recomienda

una profundidad de descarga de un 80%). Una descarga

completa de la batería conducirá a un envejecimiento

prematuro de las celdas de la batería.

Protección contra inuencias del entorno

1. Proteja su inversor y cargador de baterías contra la

humedad y la lluvia. La humedad y la lluvia pueden causar

daños severos a las celdas de las baterías.

2. No use el inversor ni el cargador de baterías cerca de

vapores y líquidos inamables.

3. Use el cargador de baterías y el inversor solo en entornos

secos y a una temperatura ambiente de entre 41°F (5°C) y

105°F (40.5°C).

4. No coloque el cargador de baterías en lugares donde la

temperatura pueda sobrepasar los 105°F (40.5°C). En

particular, no deje el cargador de baterías en un auto

estacionado bajo la luz directa del sol.

5. Proteja las baterías contra el sobrecalentamiento. Las

sobrecargas, exceso de carga y exposición a la luz directa

del sol darán como resultado un sobrecalentamiento y

daños a las celdas. Nunca cargue ni trabaje con baterías

que hayan estado sobrecalentadas. De ser posible,

reemplácelas inmediatamente.

6. Guarde el cargador de baterías y inversor solo en entornos

secos y a una temperatura ambiente de entre 41°F (5°C) y

105°F (40.5°C). Guarde su batería de iones de litio en un

lugar fresco y seco, a una temperatura ambiente de 77°F

(25°C). Proteja la batería, el cargador y el inversor contra

la humedad y la luz directa del sol. Solo almacene baterías

cargadas por completo.

7. Evite que la batería de iones de litio se congele. Las

baterías almacenadas a temperaturas menores de 32°F

(0°C) por más de una hora deberán ser desechadas.

8. Al manipular una batería, tenga cuidado con las descargas

electrostáticas. Las descargas electrostáticas pueden

dañar el sistema electrónico de protección y las celdas

de la batería. Evite las descargas electrostáticas y nunca

toque los polos de la batería.

Símbolos de seguridad

La siguiente tabla muestra y describe los símbolos de seguridad que pueden aparecer en este producto. Lea, comprenda y siga

todas las instrucciones relacionadas con esta máquina antes de intentar ensamblarla y operarla.

LEA EL(LOS) MANUAL(ES) DEL

OPERADOR: lea, comprenda y

siga todas las instrucciones en

el(los) manual(es) antes de intentar

ensamblar y operar esta unidad.

ALERTA DE SEGURIDAD: indica

una precaución, advertencia o

peligro.

Solo para uso en interiores.

¡ADVERTENCIA! No exponga la

unidad a la lluvia ni a entornos

mojados. Manténgala seca.

¡ADVERTENCIA! Peligro de choque

eléctrico.

Símbolo SímboloDescripción Descripción

Conozca su inversor portátil

Lea detenidamente el manual del operador y las instrucciones de seguridad antes de operar el inversor portátil. Compare la

ilustración debajo con el inversor portátil para familiarizarse con las ubicaciones de los diversos controles y ajustes. Conserve

este manual para futuras referencias.

1. Luz indicadora de encendido

2. Botón de encendido (luz LED

indicadora de estado)

3. Receptáculo USB-C

4. Receptáculo USB-A

5. Receptáculo CA

6. Luz LED

7. Compartimiento de batería

FRENTE REVERSO

4567

DE VENTA POR SEPARADO | Opciones de baterías y cargadores disponibles en sunjoe.com

24VBAT-LT 24VBAT-XR 24VCHRG-QC 24VCHRG-DPC24VBAT24VBAT-LTE

La page charge ...

sunjoe 24V-150WI-CT Manuel utilisateur

Marque: sunjoe

Modèle: 24V-150WI-CT

Catégorie: Chargeurs de batterie

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: sunjoe 24V-150WI-CT User manual
español: sunjoe 24V-150WI-CT Manual de usuario

sunjoe 24V-150WI-CT Manuel utilisateur

sunjoe 24V-150WI-CT Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents