STIEBEL ELTRON CON 100-300 Manuel utilisateur

Marque: STIEBEL ELTRON

Modèle: CON 100-300

Catégorie: Chauffe-eau

Taper: Manuel utilisateur

OPERATION AND INSTALLATION

FUNCIONAMIENTO E INSTALACIÓN

UTILISATION ET INSTALLATION

Wall mounted convection heater | Convector de pared | Appareil de chauffage à

convection mural

» CON 100-1 Premium

» CON 150-1 Premium

» CON 100-2 Premium

» CON 150-2 Premium

» CON 200-2 Premium

» CON 300-2 Premium

Certiﬁed to ANSI/UL Std. 2021

Conforms to CAN/CSA Std. C22.2 No.46

Certiﬁcación con ANSI/UL Std. 2021

Conforme a CAN/CSA Std. C22.2 No.46

Certiﬁé à la norme ANSI/UL Std. 2021

Conforme à la norme CAN/CSA Std. C22.2 No.46

2 | CON Premium www.stiebel-eltron-usa.com

CONTENTS | IMPORTANT INSTRUCTIONS

IMPORTANT

INSTRUCTIONS

SAVE THESE

INSTRUCTIONS

- When using electrical appliances, basic pre-

cautions should always be followed to reduce

the risk of ﬁre, electric shock, and injury to

persons, including the following:

1. Read all instructions before installing or

using this heater.

2. This heater is hot when in use. To avoid

burns, do not let bare skin touch hot surfaces.

Keep combustible materials, such as furniture,

pillows, bedding, papers, clothes, etc. and

curtains at least 3 feet (1 m) from the front of

the heater and keep them at least 3 feet (1 m)

away from the sides and rear.

3. Extreme caution is necessary when any

heater is used by or near children or invalids

and whenever the heater is left operating and

unattended.

4. Do not operate any heater after it malfunc-

tions. Disconnect power at service panel and

have heater inspected by a reputable electri-

cian before reusing. Keep children under the

age of3 away from the heater if constant su-

pervision cannot be guaranteed.

5. Do not use outdoors.

6. Do not insert or allow foreign objects to

enter any ventilation or exhaust opening as

this may cause an electric shock or ﬁre, or

damage the heater.

7. Save these instructions.

- Children from the age of 3 to 7 may switch

the heater on and off, provided they are su-

pervised or have been instructed in the safe

operation of the heater and understand any

risks that may result. This is subject to the

heater having been installed as described.

Children from the age of 3 to 7 must not plug

the power cable into its socket or adjust the

heater.

IMPORTANT INSTRUCTIONS

OPERATION

1. General information _________________________________________3

1.1 Safety instructions _______________________________________________ 3

1.2 Other symbols in this documentation _______________________ 3

1.3 Information on the heater _____________________________________ 3

1.4 Units of measurement __________________________________________ 3

2. Safety __________________________________________________________4

2.1 Intended use ______________________________________________________ 4

2.2 General safety instructions ____________________________________ 4

2.3 Test symbols ______________________________________________________ 4

3. Register your product _______________________________________5

4. Heater description ___________________________________________5

5. Operation _____________________________________________________5

5.1 Programming unit _______________________________________________ 5

5.2 Turning the heater on and off _________________________________ 6

5.3 Standby mode ____________________________________________________ 6

6. Settings _______________________________________________________6

6.1 Operating lock ____________________________________________________ 6

6.2 Standard display _________________________________________________ 6

6.3 Standard menu ___________________________________________________ 6

6.4 Conﬁguration menu _____________________________________________ 7

7. Cleaning, care and maintenance ___________________________8

8. Troubleshooting ______________________________________________9

INSTALLATION

9. Safety __________________________________________________________9

9.1 General safety instructions ____________________________________ 9

9.2 Instructions, standards and regulations ____________________ 9

10. Heater description ___________________________________________9

10.1 Standard delivery ________________________________________________ 9

11. Installation __________________________________________________ 10

11.1 Minimum clearances to hard surfaces _____________________ 10

11.2 Installing the wall mounting bracket _______________________ 10

11.3 Heater installation ______________________________________________ 10

11.4 Dismounting the heater _______________________________________ 10

11.5 Electrical connection ___________________________________________ 11

12. Commissioning _____________________________________________ 11

13. Troubleshooting ____________________________________________ 11

14. Heater handover ___________________________________________ 12

15. Speciﬁcation ________________________________________________ 12

15.1 Dimensions and connections _________________________________ 12

15.2 Data table ________________________________________________________ 13

15.3 Wiring diagrams ________________________________________________ 13

16. Warranty ____________________________________________________ 14

OPERATION

General information

www.stiebel-eltron-usa.com CON Premium | 3

ENGLISH

- The heater may be used by children aged8

and older and persons with reduced physical,

sensory or mental capabilities or a lack of ex-

perience and know-how, provided that they

are supervised or they have been instructed

on how to use the heater safely and have un-

derstood the potential risks.

- Children must never play with the heat-

er. Children must never clean the heater or

perform user maintenance unless they are

supervised.

- Parts of the heater can get very hot and may

cause burns. Particular caution is advised

when children or vulnerable persons are

present.

- To prevent the heater from overheating, never

cover it with anything.

- Never install the heater directly below a wall

socket.

- In the case of a permanent connection, the

heater must be able to be separated from the

power supply by an isolator that disconnects

all poles with at least 1/8˝ (3mm) contact

separation.

- The power cable must only be replaced (for

example if damaged) by a qualiﬁed contrac-

tor authorized by the manufacturer, using an

original spare part.

- Secure the heater as described in section

11.3, “Heater installation”, pg. 10.

OPERATION

1. General information

The chapters “Special information” and “Operation” are intended

for both users and qualiﬁed contractors.

The chapter “Installation” is intended for qualiﬁed contractors.

Note

Read these instructions carefully before using the heater

and retain them for future reference.

Pass on the instructions to a new user if required.

1.1 Safety instructions

1.1.1 Structure of safety instructions

KEYWORD Type of risk

Here, possible consequences are listed that may result

from failure to observe the safety instructions.

f Steps to prevent the risk are listed.

1.1.2 Symbols, type of risk

Symbol Type of risk

Injury

Electrocution

Burns

(burns, scalding)

1.1.3 Keywords

KEYWORD Meaning

DANGER Failure to observe this information will result in serious

injury or death.

WARNING Failure to observe this information may result in serious

injury or death.

CAUTION Failure to observe this information may result in non-seri-

ous or minor injury.

1.2 Other symbols in this documentation

Note

General information is identiﬁed by the adjacent symbol.

f Read these texts carefully.

Symbol Meaning

Material losses

(heater damage, consequential losses and environmental

pollution)

Appliance disposal

f This symbol indicates that you have to do something. The ac-

tion you need to take is described step by step.

1.3 Information on the heater

Symbol Meaning

Never cover the heater

1.4 Units of measurement

Note

All measurements are given in inches (mm) unless stated

otherwise.

OPERATION

Safety

4 | CON Premium www.stiebel-eltron-usa.com

2. Safety

2.1 Intended use

This heater is designed to heat living areas.

The heater is intended for domestic use. It can be used safely by

untrained persons. The heater can also be used in a non-domestic

environment, e.g. in a small business, as long as it is used in the

same way.

Any other use beyond that described shall be deemed inappropri-

ate. Observation of these instructions and of the instructions for

any accessories used is also part of the correct use of this heater.

2.2 General safety instructions

DANGER Electrocution

-Before cleaning, make sure the power has been

turned off at the circuit breaker panel and that the

heating element of the heater is cool.

DANGER Fire

Never operate this heater ...

-if the minimum clearances to adjacent object sur-

faces are not maintained, for example to furniture,

net curtains, curtains, textiles or other ﬂammable

materials (for minimum clearances, see "speciﬁca-

tion/dimensions and minimum clearances").

-in rooms where the appliance is at risk from ﬁre or

explosion as a result of chemicals, dust, gases or

vapors.

-in the direct proximity of pipes or containers that

carry or contain ﬂammable or explosive materials.

-if work such as laying cables, grinding or sealing is

carried out in the installation room.

-if sprays, ﬂoor polish or similar products containing

gasoline are used. Vent the room sufﬁciently before

heating.

-if an heater component is damaged, the heater has

fallen over or already had a fault.

-outdoors.

DANGER Fire

Never place any ﬂammable, combustible or insulating

objects or materials, such as laundry, blankets, maga-

zines, containers with ﬂoor polish or gasoline, spray cans

or similar on the appliance or in direct proximity to it.

WARNING Fire

Ensure that no foreign bodies enter the ventilation air

and extract air apertures. This could result in electric

shock or ﬁre or in damage to the appliance.

WARNING Fire

To prevent ﬁres ensure that the air inlets and outlets are

never blocked. Never position the appliance on soft sur-

faces, such as a bed, as this could result in the apertures

becoming blocked.

WARNING Burns

-Never place any ﬂammable, combustible or insulat-

ing objects or materials on the heater or in direct

proximity to it.

-Ensure that the air intake and discharge are never

blocked.

-Never place any objects between the heater and the

wall.

WARNING Injury

-Keep children under the age of3 away from the

heater if constant supervision cannot be guaran-

teed.

-Children from the age of 3 to 7 may switch the

heater on and off, provided they are supervised or

have been instructed in the safe operation of the

heater and understand any risks that may result.

This is subject to the heater having been installed as

described. Children from the age of 3 to 7 must not

plug the power cable into its socket or regulate the

heater.

-The heater may be used by children aged8 and

older and persons with reduced physical, sensory

or mental capabilities or a lack of experience and

know-how, provided that they are supervised or

they have been instructed on how to use the heater

safely and have understood the potential risks.

-Children must never play with the heater. Children

must never clean the heater or perform user main-

tenance unless they are supervised.

WARNING Injury

In closed rooms, temperatures can rapidly reach high

levels. Ensure constant supervision if the heater is op-

erated in a small room and the persons within that room

cannot regulate the heater or leave the room on their

own.

CAUTION Burns

Parts of the heater can get very hot and may cause burns.

Particular caution is advised when children or vulnerable

persons are present.

WARNING Overheating

To prevent the heater from overheating, never cover it

with anything.

Material losses

- Ensure that the power cable is not touching the

heater.

- Never stand on the heater.

- Never operate the heater outdoors in the open air.

2.3 Test symbols

See type plate on the appliance.

OPERATION

www.stiebel-eltron-usa.com CON Premium | 5

ENGLISH

3. Register your product

You must register this product within 90 days of

purchase on our web site in order to activate the

standard warranty or to be eligible for the extended

warranty. Go to our web site at

www.stiebel-eltron-usa.com and click on register

your product.

Before beginning the registration process, we suggest that

you gather the necessary information which will be as

follows:

Type, Example: CON 150-1 Premium (from the white label that

is on the left side of the unit)

Number listed after “No.”

Place of Purchase

Purchase Date

First & Last Name

Email address

Physical Address

Phone Number

If you have any questions concerning the registration process

or warranty options, please contact Stiebel Eltron USA direct-

ly at 800.582.8423.

4. Heater description

CON Premium is a wall mounted electric convection heater.

The heater is suitable for use as a standalone heating system,

or can be used in spring and autumn and as a booster heater in

smaller rooms.

The air inside the heater is heated by a heating element and ex-

pelled via natural convection through the air discharge at the top.

Cool indoor air is drawn in through the air intake on the underside

of the heater.

When the set room temperature is reached, it is maintained by

periodic heating.

5. Operation

D0000074791

1Programming unit

2ON/OFF switch

5.1 Programming unit

The heater is operated using the programming unit, located at

the top right front.

D0000080849

1Display

2 User interface

5.1.1 User interface

Button Designation Description

“Standby” button Switches on the programming unit;

Puts programming unit and heater into stand-

by mode

“OK” button Makes selections;

Confirms settings

“Menu” button Calls up and exits menu

“+” button Calls up menu items;

Changes settings

“–” button Calls up menu items;

Changes settings

5.1.2 Display

If there is no user input for 20seconds, the backlight switches off.

Press any button to switch the backlight on again.

Symbols

Symbol Description

Time display:

Indicates the current time, or a programmed start time

Time program activated:

Heats in accordance with the enabled time program.

Comfort mode:

The heater maintains the set comfort temperature.

Standard comfort setting: 70 °F (21.0°C). Use this setting for a

comfortable room temperature when someone is present.

Night mode:

The heater maintains the selected lower nighttime temperature.

Standard setting: 64 °F (18.0 °C). Use this setting at night or when

absent for several hours.

OPERATION

Settings

6 | CON Premium www.stiebel-eltron-usa.com

Symbol Description

Frost protection:

The frost protection symbol is displayed if the heater’s tempera-

ture is set to 45 °F (7.0 °C).

Use this setting to protect an unoccupied room from frost dam-

age.

Adaptive start:

With a time program activated, the heater activation times are

adjusted to ensure that the appropriate set room temperature is

fully reached by the programmed start time.

Conditions: The “Adaptive start” function is enabled (see chapter

“Settings/ Standard menu”).

Window open detection:

To avoid unnecessary energy consumption while venting, the

heater automatically switches to frost protection mode for one

hour if a window is opened. The "window open detection" symbol

flashes. After venting, frost protection mode can be terminated

manually by pressing "+" or "OK". The heater then heats to the set

room temperature again.

The following conditions must be fulfilled for the “Window open

detection” function to be activated:

- The set room temperature is set to 59 °F (15 °C) or higher.

- The temperature at the heater falls abruptly by at least 5.4 °F

(3 °C).

- Window open detection is switched on (see chapter “Settings/

Standard menu”).

Operating lock:

The user interface is locked.

Heating enabled:

The unit is heating to maintain the set room temperature.

Room temperature display

Editable parameter:

The parameter shown can be changed using “+” and “–”.

Days of the week:

1=Monday, 2=Tuesday … 7=Sunday

5.2 Turning the heater on and off

Note

For a short time after initial start-up, and after extended

periods without usage, a smell may brieﬂy develop.

The heater is ready for operation as soon as it has been mounted

to the wall and plugged into a wall outlet (120 V models) or hard-

wired to an appropriately sized circuit breaker (optional for 120 V

models, required for 208–240 V models).

f Turn the heater on or off using the ON/OFF switch on the

right-hand side of the heater.

f Turn the heater off when not in use for longer periods (e.g.

during the summer months).

All settings remain intact after turning off or after an interrup-

tion to the power supply. This heater is equipped with a power

reserve that allows the day of the week and the time to be saved

for several hours.

Note

If the heater has been turned off for a longer time with a

time program activated, you will be prompted to set the

day and time after switching it back on. Until this data is

entered, the heater will operate in comfort mode.

5.3 Standby mode

Material losses

In standby mode, the heater will not produce heat under

any circumstances. Frost protection is deactivated until

the heater is taken out of standby mode.

f To switch on the programming unit, press “Standby”. The

standard display appears.

f To put the programming unit and the heater into standby

mode, press “Standby”. The display shows "- - - -".

6. Settings

6.1 Operating lock

f To lock or unlock the user interface, press and hold

“+” and “–” simultaneously for 5seconds.

6.2 Standard display

D0000075500

The standard display is continuously shown. If no user input is

detected for longer than 20seconds while in the menu, the device

automatically switches to the standard display.

The standard display shows the current room set temperature, as

well as the “Editable parameter” symbol. You can use “+” and “–”

to change the room set temperature.

If the room set temperature corresponds to one of the values

established for the comfort or night mode temperature settings,

the symbol for the corresponding operating mode (comfort mode,

night mode) appears in the menu bar.

The room set temperature can also be changed manually with a

time program active. The changed set room temperature is main-

tained until the next programmed switching point is reached.

6.3 Standard menu

To access the standard menu, brieﬂy press “Menu”. You can now

call up the following menu items:

Display Description

Select day of the week and time

Select comfort temperature setting

The comfort temperature must be set at least 1 °F (0.5 °C)

higher than the night mode temperature.

Select night mode temperature setting

The night mode temperature must be set at least 1 °F (0.5 °C)

lower than the comfort temperature.

OPERATION

Settings

www.stiebel-eltron-usa.com CON Premium | 7

ENGLISH

Display Description

Switch “Window open detection” function on and off

If the Pro4 time program (120minute timer) is activated, the

“Window open detection” function is disabled.

Select time program (Pro1, Pro2, Pro3, Pro4, off)

Switch “Adaptive start” function on and off

If the Pro4 time program (120minute timer) is activated, the

“Adaptive start” function is disabled.

To change the setting of a menu item, call the relevant menu item

up using “+” and “–”. Press “OK”.

As soon as the “Editable parameter” symbol appears, you can

change the setting of the menu item with “+” and “–”. Press “OK”

to save the setting.

To exit the standard menu, press “Menu”. The standard display

appears.

6.3.1 120-minute short-time timer (Pro4)

With the 120-minute short-time timer, you can activate comfort

mode for a selected time of up to 120minutes. During this selected

time, the unit heats to the set comfort temperature. After this, the

heater operates in night mode.

f If you wish to use the 120-minute short-time timer, select

time programPro4 from the standard menu.

D0000075531

The standard display shows the selected time in minutes as well as

the “Editable parameter” symbol. Using the “+” and “-” buttons,

you can select any length of time from 10 – 120minutes.

To activate the short-time timer, press “OK”. The heater switches

to comfort mode until the end of the selected time. The minute

display ﬂashes during this period.

If you wish to stop the short-time timer, press and hold “OK” for

longer than 3seconds.

At the end of the selected time, the heater automatically reverts

to night mode.

6.4 Conﬁguration menu

Display Description

I1-I2 Actual values

Pro1-Pro3 Time programs

P1-P5 Parameter

In the conﬁguration menu, you can call up actual values, set time

programs and adjust parameters.

To access the conﬁguration menu, press and hold “Menu”. After

approx.3seconds, actual valueI1 is displayed.

Use “+” and “–” to switch between the individual actual values,

time programs, and parameters.

To exit the conﬁguration menu, press “Menu”. The standard dis-

play appears.

6.4.1 Actual values

The following actual values can be called up:

Display Description Unit

I1 Actual room temperature [°C] | [°F]

I2 Relative heating time

(The counter can be reset via parameter P5.)

[h]

Note

The counter for relative heating time(I2) counts in com-

plete hours how long the heater heats for. When the

heater is switched off, any heating phase of less than

60minutes is not recorded.

6.4.2 Time programs

Four time programs are available. Time programs Pro1 and Pro2

are pre-conﬁgured at the factory. Time program Pro3 can be set

according to your individual requirements. Time program Pro4 is

a 120-minute short timer.

Display Description

Pro1 Time program “Daily”

- Repeated: Monday to Sunday

Pro2 Time program “Weekdays”

- Repeated: Monday to Friday

Pro3 Time program “User defined”

- up to 14comfort phases, freely configurable

Pro4 120-minute short time program “Quick heat”

- User selects up to 120 minutes of comfort heating.

Note

To use a time program, select the required time pro-

gram from the standard menu (See section 6.3, “Stan-

dard menu”, pg. 6). To use Pro4, the 120-minute short

timer, see section 6.3.1, “120-minute short-time timer

(Pro4)”, pg. 7.

Note

Ensure the day of the week and the time are set correctly

when setting the time programs.

Note

The following applies to all time programs (Pro1, Pro2,

Pro3):

If the end time is later than 23:59h, the end time will

automatically be moved to the next day of the week. The

comfort phase is maintained past midnight and will end

on the next day at the set end time.

Time programs Pro1 and Pro2

You can specify the comfort mode start and end times with time

programsPro1 and Pro2. During this time period, the heater heats

to the set comfort temperature. Outside this speciﬁed time period,

the heater operates in night mode. This results in a comfort phase

OPERATION

Cleaning, care and maintenance

8 | CON Premium www.stiebel-eltron-usa.com

and a night phase, which are repeated daily(Pro1) or on every

working day (Pro2).

Theses phases are factory-set as follows:

- 08:00am - 10:00pm: Comfort mode

- 10:00pm - 08:00am: Night mode

Note

When time programPro2 is enabled, the heater operates

during weekends exclusively in night mode.

To adapt time programsPro1 and Pro2 according to your needs,

proceed as follows:

f In the conﬁguration menu, use “+” and “–” to call up the re-

quired time program.

f Press “OK”.

The start time for comfort mode is displayed.

f Use “+” and “–” to set the required start time.

f Press “OK”.

The end time for comfort mode is displayed.

f Use “+” and “–” to set the required end time.

f Press “OK” to save.

Time program Pro3

You can use time programPro3 to specify up to 14 separate com-

fort phases which are repeated weekly.

To conﬁgure a comfort phase in time programPro3, proceed as

follows:

f In the conﬁguration menu, use “+” and “–” to call up time

programPro3.

f Press “OK”.

The display shows “3---”.

f Press “OK”.

A day of the week or a group of days is displayed.

f Use “+” and “–” to select the required day or group of days.

f Press “OK”.

The start time for comfort mode is displayed.

f Use “+” and “–” to set the required start time.

f Press “OK”.

The end time for comfort mode is displayed.

f Use “+” and “–” to set the required end time.

f Press “OK”.

Comfort phase “3-01” has been conﬁgured.

f To conﬁgure a further comfort phase, use “+” and “–” in time

programPro3 to select display“3---”. Proceed as described

above.

Note

To reset the selected comfort phases, activate parame-

terP4.

f Please note that activating parameterP4 resets all

time programs (Pro1, Pro2, Pro3) to the factory set-

ting.

6.4.3 Parameters

You can call up the following parameters:

Display Description Options

P1 Room temperature offset ±3°C | ±5°F

P2 Time format 12h | 24h

P3 Temperature display units °C | °F

P4 Reset the time programs (Pro1, Pro2, Pro3). on | off

P5 Reset relative heating time on | off

To change the value of a parameter, use “+” and “–” to call up the

relevant parameter. Press “OK”.

As soon as the “Editable parameter” symbol appears, you can

change the parameter value with “+” and “–”. Press “OK” to save

the selected value.

P1: Room temperature offset

Uneven temperature distribution in the room can result in a differ-

ence between displayed actual temperatureI1 and the room tem-

perature you measure. To compensate for this difference, a room

temperature offset of ±5 °F (±3 °C) can be set via parameterP1.

Example: The heater indicates I1=70 °F (21.0 °C). You have mea-

sured a room temperature of 68 °F (20.0 °C). There is a difference

of 2 °F (1.0 °C).

f To compensate for the difference, select an offset of P1=-2.0

(-1.0).

P2: Time format

ParameterP2 allows you to specify whether the time is displayed

in 12hour or 24hour format.

P3: Temperature display units

ParameterP3 is used to specify whether the room temperature is

displayed in degrees Fahrenheit [°F] or Centigrade [°C].

P4: Reset time programs

Activating parameterP4 resets all time programs (Pro1, Pro2,

Pro3) to the factory setting.

P5: Reset relative heating time

Activating parameterP5 resets the counter for relative heating

time (I2).

7. Cleaning, care and maintenance

The heater contains no user serviceable parts.

Material losses

- Never spray cleaning spray into the air slot.

- Ensure that no moisture can enter the heater.

- If a pale brownish discoloration appears on the heater cas-

ing, wipe it off as soon as possible with a damp cloth.

- Clean the heater when cold with ordinary cleaning products.

Avoid abrasive or corrosive cleaning products.

INSTALLATION

Troubleshooting

www.stiebel-eltron-usa.com CON Premium | 9

ENGLISH

8. Troubleshooting

Problem Cause Solution

Room does not get

warm enough. Heat-

er does not get hot.

Temperature set too low

on the heater.

Check the selected room

temperature. Adjust if nec-

essary.

No power supply.

Check position of the ON/OFF

switch, check to ensure cir-

cuit breaker hasn’t tripped.

Room does not get

warm enough al-

though the heater

is hot.

Overheating. High limit

safety cut-out limits

heating output.

Eliminate the cause (dirt or

obstructions at the air intake

or discharge). Observe mini-

mum clearances.

Heat demand of the room

is greater than the heater

max output.

Minimize heat losses (Close

windows and doors. Avoid

constant venting.)

The room gets too

hot.

Heater temperature is set

too high.

Check the selected room

temperature. Adjust if nec-

essary.

The “Heating active”

symbol flashes. The

heater does not heat

up.

The electronic room

temperature controller

restricts the duration

between two start times

to at least 10minutes.

Heating remains off until

this period has expired;

the “Heating active” sym-

bol flashes.

Wait until the end of this

period between two start

times.

Window open de-

tection does not

respond.

Heater does not detect a

pronounced temperature

drop when venting. (Win-

dow open detection re-

quires a previously stable

room temperature.)

Wait a while after making

settings on the heater, until

the room temperature has

fully stabilized.

Avoid obstructions to air

changes between heater and

indoor air.

Install the heater in direct

proximity to a window.

Vent the room by fully open-

ing a window.

Manually switch the heater

to standby mode for the du-

ration of venting.

The set room tempera-

ture is set lower than

59 °F (15 °C).

Change the set room tem-

perature to 59 °F (15 °C) or

higher.

Window open detection

is not enabled.

Switch on window open

detection in the standard

menu.

“Adaptive start”

function does not

work as required.

This function is only

effective with a time pro-

gram activated.

Use the time programs for

optimized heating conve-

nience.

Severely fluctuating room

temperature or the heat-

er learning procedure

has not been completed.

Wait a few days for the be-

havior to stabilize.

“Adaptive start” function

is not enabled.

Switch on the “Adaptive

start” function in the stan-

dard menu.

“Err” or “E...” is dis-

played.

Thermistor sensor loose

or disconnected.

Disconnect heater from the

power supply. Check the

main control board to ensure

the thermistor sensor plug

has not become loose or dis-

connected and is fully seated

on the board.

Thermistor sensor is

faulty.

Contact qualified contractor

to replace thermistor sensor.

If you cannot ﬁx the problem, please contact your qualiﬁed con-

tractor. To facilitate and speed up your request, provide the num-

ber from the type plate (000000-0000-000000).

INSTALLATION

9. Safety

Only a qualiﬁed contractor should carry out installation, commis-

sioning, maintenance and repair of the heater.

9.1 General safety instructions

We guarantee trouble-free function and operational reliability only

if original accessories and spare parts intended for the heater

are used.

DANGER Electrocution

Carry out all electrical connection and installation

work in accordance with all national, state and local

building code.

CAUTION Burns

-Only mount the heater on a vertical wall that is tem-

perature-resistant to at least 185 °F (85 °C).

-Maintain the minimum clearances to adjacent ob-

jects.

Material losses

- If connecting the heater via a wall outlet plug, en-

sure that it is easily accessible once the heater has

been installed.

- Never install the heater directly below a wall socket.

- Ensure that the power cable is not in contact with

any heater components.

9.2 Instructions, standards and regulations

Note

Observe all applicable national and regional regulations

and instructions.

10. Heater description

10.1 Standard delivery

The following are delivered with the heater:

- Wall mounting bracket (hooked into the heater)

- Power cord with 120 V plug (120 V models only, attached)

INSTALLATION

Installation

10 | CON Premium www.stiebel-eltron-usa.com

11. Installation

11.1 Minimum clearances to hard surfaces

Ý

FP

Ý

FP

Ý

FP

Ý

FP

Ý

FP

ANY HARD SURFACE

FLOOR

D0000074786

11.2 Installing the wall mounting bracket

The heater is intended for wall mounting using the supplied wall

mounting bracket. The heater may only be installed horizontally.

Note

- The wall mounting bracket can be used as a tem-

plate for wall mounting. This ensures sufﬁcient

clearance from the ﬂoor.

- Use a level if the ﬂoor is uneven or sloping.

aaa

D0000072159

ôÝ ôÝ

FP FP

D0000074785

fUnhook the wall mounting bracket from the heater.

fPlace the centred wall mounting bracket horizontally on the

ﬂoor. Mark holes1 and 2.

fLift up the wall mounting bracket so that its lower holes

match up with the markings you have just made on the in-

stallation wall.

fMark holes3 and 4 on the installation wall.

fDrill the holes at the 4markings.

fSecure the wall mounting bracket with suitable ﬁxing mate-

rials (screws, wall anchors). With the vertical slots, you can

compensate for an offset mounting hole.

11.3 Heater installation

D0000074782

1 Wall mounting bracket

fHook the heater onto the bottom tabs of the wall mounting

bracket by the slots in the back of the heater.

fPlace the heater in an upright position.

fSecure the heater by pushing it towards the wall until it au-

dibly snaps into place in the two upper springs on the wall

mounting bracket.

D0000074783

1 Heater

2 Captive locking screws (attached)

3 Secure the heater against unintentional release, using the

supplied captive locking screws on the left- and right-hand

sides of the wall mounting bracket.

11.4 Dismounting the heater

fLoosen the captive locking screws attached to the wall

mounting bracket.

fTo release the heater, push down the springs at the top of the

wall mounting bracket.

fTilt the heater away from the wall and lift it off the bottom

tabs of the wall mounting bracket.

INSTALLATION

Commissioning

www.stiebel-eltron-usa.com CON Premium | 11

ENGLISH

11.5 Electrical connection

DANGER Electrocution

Carry out all electrical connection and installation work

in accordance with all national, state and local building

code.

WARNING Electrocution

In the case of a permanent connection, the heater must

be able to be separated from the power supply by an iso-

lator that disconnects all poles with at least 1/8˝ (3mm)

contact separation.

Material losses

- Observe the type plate. The speciﬁed voltage must

match the mains voltage.

- Ensure the on-site power supply cable is of an ade-

quate gauge to meet all applicable codes.

11.5.1 CON Premium 120 V models

120 V CON Premium models are delivered fully wired. The follow-

ing electrical connections are permissible:

CON 100-1 Premium

CON 150-1 Premium

Connection to a freely accessible standard 120 V

outlet with grounded plug

Hard-wired connection to an appliance junction

box with ground conductor

Connection to a standard wall outlet

D0000076073

1 Retainer for power cable

Material losses

The power cable must not be pushed into the space be-

tween the appliance back panel and the wall on which

it is installed.

fWind up any extra power cable around the cable

retainer on the back of the appliance.

fPlug the heater into a grounded 120 V wall outlet.

120 V hard-wired connection to a circuit breaker

Material losses

- Trim the power cable so it leads directly to the heat-

er connection socket.

- Ensure that, after trimming the power cable, the

heater can still be removed from the wall without

issue.

fTrim the power cable by cutting off the plug.

fConnect the trimmed end of the power cable to a suitable

appliance junction box.

fThe appliance junction box must be connected to a circuit

breaker of suitable size. See section 15.2, “Data table”, pg.

13.

11.5.2 CON Premium 208–240 V models, hard-wired connection

to a circuit breaker

CON Premium 208–240 V models have a junction box located at

the right rear of the unit. Included in the junction box are wires

with wire nuts attached.

fInstall a ½˝ ROMEX clamp in the knockout of the junction box

at the rear of the unit to prevent the power cable from being

pulled out of the wiring block during operation.

fCable must be routed from a circuit breaker of suitable size,

through the ROMEX clamp, and connected using the wire

nuts in the junction box of the unit. See section 15.3, “Wiring

diagrams”, pg. 13.

fAlternatively, the installer may remove the supplied wires

with nuts from the heater’s wiring block, run wire of a suit-

able gauge through the installed ½˝ ROMEX clamp, and con-

nect the wire ends directly to the heater’s wiring block. See

section 15.3, “Wiring diagrams”, pg. 13.

Ensure the circuit breaker is a suitable size and the power cable

is a suitable gauge. See section 15.2, “Data table”, pg. 13 for

electrical requirements.

11.5.3 Wiring block

Consult the chart below for the recommended torque amounts on

the wiring block screws.

Screw Size (mm) Min. Torque (N•cm) Min. Torque (lbf•in)

M3.5 60–80 5.31–7.08

Using the proper torque speciﬁcations to secure wire to the wiring

block helps to avoid personal loss or property damage.

12. Commissioning

The heater is ready for operation as soon as it has been mounted

to the installation wall and connected to the power supply.

fRemove the protective ﬁlm from the programming unit.

13. Troubleshooting

The power cable must only be replaced (for example if damaged)

by a qualiﬁed contractor authorized by the manufacturer, using

an original spare part.

INSTALLATION

Heater handover

12 | CON Premium www.stiebel-eltron-usa.com

14. Heater handover

Explain the functions of the heater to the user. Draw special at-

tention to the safety instructions. Hand over the operating and

installation instructions to the user.

15. Speciﬁcation

15.1 Dimensions and connections

a20

18½Ý

(470)

415/16Ý

(126)

10ǩÝ

(256)

i13

b01

D0000081187

CON 100-1 Premium

CON 100-2 Premium

CON 150-1 Premium

CON 150-2 Premium

CON 200-2 Premium CON 300-2 Premium

a20 Heater Width 18½˝ (470 mm) 245/8˝ (625 mm) 30¾˝ (780 mm) 427/8˝ (1090 mm)

b01 Entry electrical

cables

i13 Wall mounting

bracket

Horizontal hole

spacing

7˝ (179 mm) 13¼˝ (335 mm) 193/8˝ (491 mm) 315/8˝ (803 mm)

INSTALLATION

ZĤ¼êÐ|ŒêĒĉ

www.stiebel-eltron-usa.com CON Premium | 13

ENGLISH

15.2 Data table

CON 100-1

Premium

CON 150-1

Premium

CON 100-2

Premium

CON 150-2

Premium

CON 200-2

Premium

CON 300-2

Premium

Item number 202025 202026 202027 202028 202029 202030

Electrical data

Power supply - 50/60 Hz single phase single phase single phase single phase single phase single phase

Voltage 120 V 120 V 240 V 208 V 240 V 208 V 240 V 208 V 240 V 208 V

Wattage 1000 W 1500 W 1000 W 750 W 1500 W 1125 W 2000 W 1500 W 3000 W 2250 W

Btu/hr 3412 5118 3412 2559 5118 3839 6824 5118 10236 7677

Amperage 8.3 A 12.5 A 4.2 A 3.6 A 6.3 A 5.4 A 8.3 A 7.2 A 12.5 A 10.8 A

Required circuit breaker size115 A 15 A 10 A 10 A 10 A 10 A 15 A 15 A 15 A 15 A

Required wire size114 AWG 14 AWG 14 AWG 14 AWG 14 AWG 14 AWG 14 AWG 14 AWG 14 AWG 14 AWG

Electrical connection Power cord with

plug

Power cord with

plug

Junction box, rear Junction box, rear Junction box, rear Junction box, rear

Dimensions

Height 18½˝ (470 mm) 18½˝ (470 mm) 18½˝ (470 mm) 18½˝ (470 mm) 18½˝ (470 mm) 18½˝ (470 mm)

Width 18½˝ (470 mm) 245/8˝ (625 mm) 18½˝ (470 mm) 245/8˝ (625 mm) 30¾˝ (780 mm) 427/8˝ (1090 mm)

Depth 415/16˝ (126 mm) 415/16˝ (126 mm) 415/16˝ (126 mm) 415/16˝ (126 mm) 415/16˝ (126 mm) 415/16˝ (126 mm)

Weights

Weight 13.0 lb (5.9 kg) 16.5 lb (7.5 kg) 13.0 lb (5.9 kg) 16.5 lb (7.5 kg) 22.5 lb (10.2 kg) 27.8 lb (12.6 kg)

Other data

Type Wall mounted convection heater

Color Alpine white

Settings

Temperature range 41-86 °F (5-30 °C)

Frost protection setting 45 °F (7 °C)

1 This is our recommendation as the manufacturer. Check local codes for compliance if necessary.

15.3 Wiring diagrams

15.3.1 120 V wiring diagram for CON 100-1, CON 150-1 Premium

GND

L L1



8pol.

Rt - Sensor

UI User Interface

FSH FSH/FSV

FSH

A1 = Power PCBA

(Z1) (Z2) (Z3)

15.3.2 208–240 V wiring diagram for CON 100-2, CON 150-2,

CON 200-2, CON 300-2

L1 L2 GND

L L1



8pol.

Rt - Sensor

UI User Interface

FSH FSH/FSV

FSH

A1 = Power PCBA

(Z1) (Z2) (Z3)

14 | CON Premium www.stiebel-eltron-usa.com

WARRANTY | ENVIRONMENT AND RECYCLING

LIMITED WARRANTY

Subject to the terms and conditions set forth in this limited

warranty, Stiebel Eltron, Inc. (the “Manufacturer”) hereby

warrants to the original purchaser (the “Owner”) that

each Electric Space Heater (the “Heater”) shall be free of

defects in the Manufacturer’s materials or workmanship

for a period of three (3) years from the date of purchase.

As Owner’s sole and exclusive remedy for breach of the

above warranty, Manufacturer shall, at the Manufacturer’s

discretion, send replacement parts for local repair; retrieve

the unit for factory repair, or replace the defective Heater

with a replacement unit with comparable operating

features. Manufacturer’s maximum liability under all

circumstances shall be limited to the Owner’s purchase

price for the Heater.

This limited warranty shall be the exclusive warranty

made by the Manufacturer and is made in lieu of all other

warranties, express or implied, whether written or oral,

including, but not limited to warranties of merchantability

and ﬁ tness for a particular purpose. Manufacturer shall

not be liable for incidental, consequential or contingent

damages or expenses arising directly or indirectly from any

defect in the Heater or the use of the Heater. Manufacturer

shall not be liable for any damage to property of Owner

arising, directly or indirectly, from any defect in the Heater

or the use of the Heater. Manufacturer alone is authorized

to make all warranties on Manufacturer’s behalf and no

statement, warranty or guarantee made by any other party

shall be binding on Manufacturer.

Manufacturer shall not be liable for any damage

whatsoever relating to or caused by:

1. any misuse or neglect of the Heater, any accident to

the Heater, any alteration of the Heater, or any other

unintended use;

2. acts of God and circumstances over

which Manufacturer has no control;

3. installation of the Heater other than as directed by

Manufacturer and other than in accordance with

applicable building codes;

4. failure to maintain the Heater or to operate the Heater

in accordance with the Manufacturer’s speciﬁ cations;

5. improper installation and/or improper materials used

by any installer and not relating to defects in parts or

workmanship of Manufacturer;

6. moving the Heater from its original place of installation;

7. use on improper voltage or current;

8. disassembly, repair, or alteration by anyone other than

the manufacturer.

Should owner wish to return the Heater to manufacturer

for repair or replacement under this warranty, Owner

must ﬁ rst secure written authorization from Manufacturer.

Owner shall demonstrate proof of purchase, including a

purchase date, and shall be responsible for all removal

and transportation costs. If Owner cannot demonstrate a

purchase date this warranty shall be limited to the period

beginning from the date of manufacture stamped on the

Heater. Manufacturer reserves the right to deny warranty

coverage upon Manufacturer’s examination of Heater.

This warranty is restricted to the Owner and cannot be

assigned.

Some States and Provinces do not allow the exclusion

or limitation of certain warranties. In such cases, the

limitations set forth herein may not apply to the Owner. In

such cases this warranty shall be limited to the shortest

period and lowest damage amounts allowed by law. This

warranty gives you speciﬁ c legal rights and you may also

have other rights which vary from State to State or Province

to Province.

Owner shall be responsible for all labor and other charges

incurred in the removal or repair of the Heater in the ﬁ eld.

This Warranty is valid for U.S.A. & Canada only. Warranties

may vary by country. Please consult your local Stiebel Eltron

Representative for the Warranty for your country.

! The installation, electrical connection and ﬁrst operati-

on of this appliance should be carried out by a qualiﬁed

installer.

! The company does not accept liability for failure of any

goods supplied which have not been installed and ope-

rated in accordance with the manufacturer‘s

instructions.

Environment and recycling

Please help us to protect the environment by disposing of the

packaging in accordance with the national regulations for waste

processing.

16. Warranty

www.stiebel-eltron-usa.com CON Premium | 15

ESPAÑOL

ÍNDICE | INSTRUCCIONES IMPORTANTES

INSTRUCCIONES

IMPORTANTES

GUARDA ESTAS

INSTRUCCIONES

- Al utilizar aparatos eléctricos, siempre se

deben seguir las precauciones básicas para

reducir el riesgo de incendio, descarga eléc-

trica y lesiones a las personas, incluidas las

siguientes:

1. Lea todas las instrucciones antes de instalar

o usar este calentador.

2. Este calentador se calienta cuando está en

uso. Para evitar quemaduras, no permita que

la piel desprotegida toque superﬁcies calien-

tes. Mantenga los materiales combustibles,

como muebles, almohadas, ropa de cama,

papeles, ropa y cortinas, al menos a 3 pies

(1 m) de la parte frontal, los lados y la parte

posterior del calentador.

3. Se requiere extrema precaución cuando

niños o personas con discapacidad usan el

calentador o están cerca de él y cuando el

calentador se deja en funcionamiento sin su-

pervisión.

4. No opere ningún calentador si observa

que funciona incorrectamente. Desconecte el

cable de alimentación en el panel de servi-

cio y solicite a un electricista acreditado que

inspeccione el calentador antes de volver a

utilizarlo. Mantenga a los niños menores de

3 años alejados del calentador si no se puede

garantizar la supervisión constante.

5. No lo use al aire libre.

6. No introduzca ni permita que entren ob-

jetos extraños en ninguna abertura de ven-

tilación o de extracción, ya que esto puede

causar una descarga eléctrica o un incendio,

o dañar el calentador.

7. Guarda estas instrucciones.

INSTRUCCIONES IMPORTANTES

OPERACIÓN

1. Información general _______________________________________ 16

1.1 Instrucciones de seguridad ___________________________________ 16

1.2 Otros símbolos en esta documentación ____________________ 16

1.3 Información sobre el calentador ____________________________ 17

1.4 Unidades de medida ___________________________________________ 17

2. Seguridad ___________________________________________________ 17

2.1 Uso previsto ______________________________________________________ 17

2.2 Instrucciones generales de seguridad ______________________ 17

2.3 Símbolos de prueba ____________________________________________ 18

3. Registre su producto ______________________________________ 18

4. Descripción del calentador ________________________________ 18

5. Operación ___________________________________________________ 18

5.1 Unidad de programación ______________________________________ 18

5.2 Encendido y apagado del calentador _______________________ 19

5.3 Modo de espera _________________________________________________20

6. Conﬁguración _______________________________________________ 20

6.1 Bloqueo ___________________________________________________________ 20

6.2 Visualización estándar _________________________________________ 20

6.3 Menú estándar __________________________________________________ 20

6.4 Menú de conﬁguración ________________________________________21

7. Limpieza, cuidado y mantenimiento _____________________ 22

8. Resolución de problemas _________________________________ 22

INSTALACIÓN

9. Seguridad ___________________________________________________ 23

9.1 Instrucciones generales de seguridad ______________________23

9.2 Instrucciones, estándares y regulaciones __________________ 23

10. Descripción del calentador ________________________________ 23

10.1 Entrega estándar _______________________________________________ 23

11. Instalación __________________________________________________ 23

11.1 Distancias mínimas con respecto a superﬁcies duras ___ 23

11.2 Instalación del soporte de montaje en pared _____________23

11.3 Instalación del calentador ____________________________________ 24

11.4 Desmontaje del calentador ___________________________________ 24

11.5 Conexión eléctrica ______________________________________________ 24

12. Puesta en marcha __________________________________________ 25

13. Resolución de problemas _________________________________ 25

14. Transferencia del calentador _____________________________ 25

15. Especiﬁcaciones ____________________________________________ 26

15.1 Dimensiones y conexiones ____________________________________ 26

15.2 Tabla de datos ___________________________________________________26

15.3 Diagramas de cableado _______________________________________ 27

16. Garantía _____________________________________________________ 28

OPERACIÓN

Información general

16 | CON Premium www.stiebel-eltron-usa.com

- Los niños de entre 3 y 7 años pueden encen-

der y apagar el calentador siempre que sean

supervisados o que se les haya enseñado el

funcionamiento seguro del calentador y com-

prendan los riesgos potenciales. Esto depende

de que el calentador se haya instalado como

se indica. Los niños de entre 3 y 7 años no

deben enchufar el cable de alimentación ni

regular el calentador.

- El calentador puede ser utilizado por niños

de 8 años en adelante, por personas con dis-

capacidades físicas, sensoriales o mentales o

por personas sin experiencia o conocimientos

suﬁcientes siempre que sean supervisados o

que se les haya enseñado el funcionamiento

seguro del calentador y hayan comprendido

los riesgos potenciales.

- Los niños nunca deben jugar con el calen-

tador. Tampoco deben limpiarlo ni reali-

zar el mantenimiento a menos que sean

supervisados.

- Algunas partes del calentador pueden alcan-

zar altas temperaturas y causar quemaduras.

Se recomienda especial precaución cuando

haya niños o personas vulnerables cerca.

- Para evitar que el calentador se sobrecaliente,

nunca lo cubra.

- Nunca instale el calentador directamente de-

bajo de una toma de corriente.

- En el caso de una conexión permanente, el

calentador debe poder separarse de la fuente

de alimentación mediante un aislador que

desconecte todos los polos con una separa-

ción de contactos de al menos 1/8˝ (3 mm).

- El cable de alimentación solo debe ser re-

emplazado (por ejemplo, si está dañado) por

un contratista caliﬁcado autorizado por el

fabricante, utilizando una pieza de repuesto

original.

- Fije el calentador como se describe en el ca-

pítulo 11.3, “Instalación del calentador”, pág.

24.

OPERACIÓN

1. Información general

Los capítulos “Información especial” y “Operación” están destina-

dos tanto a usuarios como a contratistas caliﬁcados.

El capítulo “Instalación” está destinado solo a contratistas cali-

ﬁcados.

Nota

Lea estas instrucciones con atención antes de usar el ca-

lentador y consérvelas para referencia futura.

Entregue las instrucciones a un nuevo usuario si es ne-

cesario.

1.1 Instrucciones de seguridad

1.1.1 Estructura de las instrucciones de seguridad

PALABRA CLAVE Tipo de riesgo

Aquí se enumeran las consecuencias que pueden resultar

del incumplimiento de las instrucciones de seguridad.

f Se enumeran los pasos para evitar el riesgo.

1.1.2 Símbolos, tipo de riesgo

Símbolo Tipo de riesgo

Lesión

Electrocución

Quemaduras

((quemaduras, escaldaduras)

1.1.3 Palabras clave

PALABRA CLAVE Significado

PELIGRO El incumplimiento de esta información provocará lesio-

nes graves o la muerte.

ADVERTENCIA El incumplimiento de esta información puede provocar

lesiones graves o la muerte.

PRECAUCIÓN El incumplimiento de esta información puede ocasionar

lesiones no graves o leves.

1.2 Otros símbolos en esta documentación

Nota

La información general se identiﬁca con el símbolo ad-

yacente.

f Lea estos textos cuidadosamente.

Símbolo Significado

Pérdidas materiales

(daños en el calentador, pérdidas consecuentes y contami-

nación ambiental)

OPERACIÓN

Seguridad

www.stiebel-eltron-usa.com CON Premium | 17

ESPAÑOL

Eliminación de electrodomésticos

f Este símbolo indica que tienes que hacer algo. La acción que

tienes que hacer se describe paso a paso.

1.3 Información sobre el calentador

Símbolo Significado

Nunca cubra el calentador

1.4 Unidades de medida

Nota

Todas las medidas se dan en mm (pulgadas), a menos

que se indique lo contrario.

2. Seguridad

2.1 Uso previsto

Este calentador está diseñado para calentar áreas habitables.

Está destinado para uso doméstico y puede ser utilizado de ma-

nera segura por personas no capacitadas. El calentador también

se puede usar en un entorno no doméstico; por ejemplo, en una

pequeña empresa, siempre que se use de la misma manera.

Cualquier otro uso más allá del descrito se considerará inapro-

piado. La observación de estas instrucciones y de las instruccio-

nes para cualquier accesorio utilizado también es parte del uso

correcto de este calentador.

2.2 Instrucciones generales de seguridad

PELIGRO Electrocución

-Antes de limpiar el calentador, asegúrese de que se

haya apagado desde el panel del disyuntor y de que

el elemento calefactor esté frío.

PELIGRO Incendio

Nunca opere este calentador...

-si no se mantienen las distancias mínimas con

respecto a los objetos adyacentes; por ejemplo,

muebles, cortinas de red, cortinas, textiles u otros

materiales inﬂamables (para más información sobre

distancias mínimas, consulte la sección 15.1, “Di-

mensiones y conexiones”, pág. 26).

-en habitaciones donde el aparato corre riesgo de

incendio o explosión como resultado del contacto

con productos químicos, polvo, gases o vapores.

-en la proximidad directa de tuberías o contenedores

que transportan o contienen materiales inﬂamables

o explosivos.

-si se realizan trabajos tales como tendido de cables,

rectiﬁcado o sellado en la sala de instalación.

-si se usan aerosoles, cera para pisos o productos

similares que contienen gasolina. Ventile la habita-

ción lo suﬁciente antes de calefaccionarla.

-si un componente del aparato está dañado, si se ha

caído o si ya tiene una falla.

-al aire libre.

PELIGRO Incendio

Nunca coloque objetos o materiales inﬂamables, com-

bustibles o aislantes, tales como ropa, mantas, revistas,

recipientes con cera para pisos o gasolina, latas de aero-

sol o similares, sobre el aparato o cerca de él.

ADVERTENCIA Incendio

Asegúrese de que no entren cuerpos extraños en el

canal de ventilación y tapen las aberturas. Esto podría

provocar descargas eléctricas, incendios o daños en el

aparato.

ADVERTENCIA Incendio

Para evitar incendios, asegúrese de que las entradas y

salidas de aire nunca estén bloqueadas. Nunca coloque

el aparato sobre superﬁcies blandas, como una cama,

ya que esto podría bloquear las aberturas.

ADVERTENCIA Quemaduras

-Nunca coloque objetos o materiales inﬂamables,

combustibles o aislantes sobre el calentador o cerca

de él.

-Asegúrese de que la entrada y descarga de aire

nunca estén bloqueadas.

-Nunca coloque objetos entre el calentador y la

pared.

OPERACIÓN

Registre su producto

18 | CON Premium www.stiebel-eltron-usa.com

ADVERTENCIA Lesiones

-Mantenga a los niños menores de 3 años alejados

del calentador si no se puede garantizar una super-

visión constante.

-Los niños de entre 3 y 7 años pueden encender y

apagar el calentador siempre que sean supervisa-

dos o que se les haya enseñado el funcionamiento

seguro del calentador y comprendan los riesgos

potenciales. Esto depende de que el calentador se

haya instalado como se indica. Los niños de entre 3

y 7 años no deben enchufar el cable de alimentación

ni regular el calentador.

-El calentador puede ser utilizado por niños de 8

años en adelante, por personas con discapacidades

físicas, sensoriales o mentales o sin experiencia o

conocimientos suﬁcientes siempre que sean super-

visados o que se les haya enseñado el funciona-

miento seguro del calentador y hayan comprendido

los riesgos potenciales.

-Los niños nunca deben jugar con el calentador.

Tampoco deben limpiarlo ni realizar el manteni-

miento a menos que sean supervisados.

ADVERTENCIA Lesiones

IEn habitaciones cerradas, las temperaturas pueden

alcanzar rápidamente niveles elevados. Procure una

supervisión constante si el calentador funciona en una

habitación pequeña y las personas que están en esa ha-

bitación no pueden regularlo o abandonar la habitación

por su cuenta.

PRECAUCIÓN Quemaduras

Algunas partes del calentador pueden alcanzar altas tem-

peraturas y causar quemaduras. Se recomienda especial

precaución cuando haya niños o personas vulnerables

cerca.

ADVERTENCIA Sobrecalentamiento

Para evitar que el calentador se sobrecaliente, nunca lo

cubra.

Pérdidas materiales

- Asegúrese de que el cable de alimentación no toque

el calentador.

- Nunca se pare sobre el calentador.

- Nunca opere el calentador al aire libre.

2.3 Símbolos de prueba

Ver placa de características en el calentador.

3. Registre su producto

Debe registrar este producto dentro de los 90 días

posteriores a la compra en nuestro sitio web para

activar la garantía estándar o solicitar la garantía

extendida. Vaya a nuestro sitio web en

www.stiebel-eltron-usa.com y haga clic en Registrar

su producto.

Antes de comenzar el proceso de registro, le sugerimos que

recopile la información necesaria, a saber:

Tipo, ejemplo: CON 150-1 Premium (en la etiqueta blanca que

se encuentra en el lado izquierda de la unidad)

Número listado después de “No.”

Lugar de compra

Fecha de compra

Nombre y apellido

Dirección de correo electrónico

Domicilio

Número de teléfono

Si tiene alguna pregunta sobre el proceso de registro o las

opciones de garantía, comuníquese directamente con Stiebel

Eltron USA al 800.582.8423.

4. Descripción del calentador

CON Premium es un calentador de convección eléctrico de montaje

en pared.

El calentador es adecuado para su uso como sistema de calefac-

ción independiente, o puede usarse en primavera y otoño y como

un calentador de refuerzo en habitaciones más pequeñas.

El aire en su interior es calentado por un elemento calefactor y

expulsado por convección natural a través de la descarga de aire

en la parte superior. Se aspira aire fresco del ambiente a través

de la entrada de aire en la parte inferior del calentador.

Cuando se alcanza la temperatura ambiente establecida, se man-

tiene mediante el calentamiento periódico.

5. Operación

D0000074791

1 Unidad de programación

2 Interruptor de ENCENDIDO/APAGADO

5.1 Unidad de programación

El calentador se opera desde la unidad de programación, ubicada

en la parte superior derecha delantera.

OPERACIÓN

Operación

www.stiebel-eltron-usa.com CON Premium | 19

ESPAÑOL

D0000080849

1 Visualización

2 Interfaz de usuario

5.1.1 Interfaz de usuario

Botón Designación Descripción

Botón “Standby”

(“Espera”)

Enciende la unidad de programación;Configu-

ra la unidad de programación y el calentador

en modo de espera

Botón “OK” Hace selecciones;

Confirma la configuración

Botón “Menu”

(“Menú”)

Ingresa a y sale del menú

Botón “+” Selecciona elementos del menú;

Cambia la configuración

Botón “-” Selecciona elementos del menú;

Cambia la configuración

5.1.2 Visualización

Si el usuario no realiza una selección al cabo de 20 segundos, la

luz de fondo se apaga. Presione cualquier botón para volver a

encender la luz de fondo.

Símbolos

Símbolo Descripción

Visualización de la hora:

Indica la hora actual o una hora de inicio programada

Programa de temporizador activado:

Calienta de acuerdo con el programa de temporizador configu-

rado.

Modo de confort:

El calentador mantiene la temperatura de confort establecida.

Ajuste de confort estándar: 70°F (21.0 °C). Use esta configuración

para una temperatura ambiente cómoda cuando haya alguien

presente.

Modo nocturno:

El calentador mantiene la temperatura nocturna más baja selec-

cionada.

Configuración estándar: 64 °F (18.0 °C). Use esta configuración

por la noche o cuando esté ausente por varias horas.

Símbolo Descripción

Protección contra heladas:

El símbolo de protección contra heladas se muestra si la tempera-

tura del calentador se establece en 45 °F (7.0 °C).

Use esta configuración para proteger una habitación desocupada

del daño por heladas.

Inicio adaptativo:

Con el programa de temporizador activado, los tiempos de activa-

ción del calentador se ajustan para garantizar que la temperatura

ambiente establecida se alcance en el momento de inicio progra-

mado.

Condiciones: La función “Inicio adaptativo” está habilitada (con-

sulte la sección 6.3, “Menú estándar”, pág. 20).

Detección de ventana abierta:

Para evitar el consumo innecesario de energía durante la venti-

lación, el calentador cambia automáticamente al modo de pro-

tección contra heladas durante una hora si se abre una ventana.

El símbolo de “detección de ventana abierta” parpadea. Después

de la ventilación, el modo de protección contra heladas se puede

apagar manualmente presionando “+” u “OK”. El calentador ca-

lienta nuevamente a la temperatura ambiente establecida.

Para que se active la función de “Detección de ventanas abiertas”

deben cumplirse las siguientes condiciones:

- La temperatura ambiente está fijada en 59 °F (15 °C) o más.

- La temperatura en el calentador cae abruptamente al menos

5.4°F (3°C).

- La detección de ventanas abiertas está activada (consulte la sec-

ción 6.3, “Menú estándar”, pág. 20).

Bloqueo:

La interfaz de usuario está bloqueada.

Calefacción habilitada:

La unidad se calienta para mantener la temperatura ambiente

establecida.

Visualización de la temperatura ambiente

Parámetro editable:

El parámetro que se muestra se puede cambiar con “+” y “-”.

Días de la semana:

1 = lunes, 2 = martes... 7 = domingo

5.2 Encendido y apagado del calentador

Nota

Durante un corto tiempo después de la puesta en marcha

inicial y después de períodos prolongados sin uso, el

calentador puede emanar cierto olor brevemente.

El calentador estará listo para funcionar tan pronto como se haya

montado en la pared y enchufado a una toma de corriente (mo-

delos de 120 V) o bien conectado directamente a un disyuntor de

tamaño adecuado (opcional para los modelos de 120 V, requerido

para los modelos de 208–240 V).

fEncienda o apague el calentador usando el interruptor de

ENCENDIDO/APAGADO en el lado derecho de la unidad.

fApague el calentador cuando no esté en uso por períodos

más largos (por ejemplo, durante los meses de verano).

Todos los ajustes permanecen intactos después de apagar o

después de una interrupción del suministro de energía. Este ca-

lentador está equipado con una reserva de energía que permite

guardar el día de la semana y la hora durante varias horas.

OPERACIÓN

ĒĉÐÖşļ|êēĉ

20 | CON Premium www.stiebel-eltron-usa.com

Nota

Si el calentador se ha apagado durante más tiempo con

un programa de tiempo activado, se le pedirá que ajuste

el día y la hora después de volver a encenderlo. Hasta

que se introduzcan estos datos, el calentador funcionará

en modo de confort.

5.3 Modo de espera

Pérdidas materiales

En modo de espera, el calentador no producirá calor bajo

ninguna circunstancia. La protección contra heladas se

desactiva hasta que el calentador salga del modo de es-

pera.

f Para encender la unidad de programación, presione “Espe-

ra”. Aparece la visualización estándar.

f Para conﬁgurar la unidad de programación y el calentador

de calefacción en modo de espera, presione “Espera”. La vi-

sualización muestra “- - - -”.

6. Conﬁguración

6.1 Bloqueo

f Para bloquear o desbloquear la interfaz de usuario, man-

tenga presionados “+” y “-” simultáneamente durante 5

segundos.

6.2 Visualización estándar

D0000075500

La visualización estándar se muestra de manera continua. Si no

se detecta ninguna selección del usuario durante más de 20 se-

gundos mientras está navegando el menú, el dispositivo cambia

automáticamente a la visualización estándar.

La visualización estándar muestra la temperatura actual de la

habitación, así como el símbolo “Parámetro editable”. Puede usar

“+” y “-“ para cambiar la temperatura ambiente establecida.

Si la temperatura ambiente establecida corresponde a uno de los

valores determinados para la temperatura del modo confort o el

modo nocturno, aparece el símbolo del modo operativo corres-

pondiente (modo confort, modo nocturno) en la barra de menú.

La temperatura ambiente ajustada también se puede cambiar ma-

nualmente con un programa de tiempo activo. La temperatura

ambiente ajustada se mantiene hasta que se alcanza el siguiente

punto de conmutación programado.

6.3 Menú estándar

Para acceder al menú estándar, presione brevemente “Menú”.

Ahora puede seleccionar los siguientes elementos del menú:

Visualiza-

ción

Descripción

Seleccionar el día de la semana y la hora

Seleccionar la configuración de temperatura de confort

La temperatura de confort debe establecerse al menos 1 °F

(0.5 °C) más alta que la temperatura del modo nocturno.

Seleccionar la configuración de temperatura del modo noc-

turno. La temperatura del modo nocturno debe establecerse

al menos 1 °F (0.5 °C) más baja que la temperatura de con-

fort.

Activar y desactivar la función “Detección de ventana abierta”

Si el programa de tiempo Pro4 (temporizador de 120 minu-

tos) está activado, la función “Detección de apertura de ven-

tanas” está desactivada.

Seleccionar el programa de temporizador (Pro1, Pro2, Pro3,

Pro4) o desactivarlo (apagado)

Activar y desactivar la función “Inicio adaptativo”

Si el programa de tiempo Pro4 (temporizador de 120 minu-

tos) está activado, la función “Inicio adaptable” está desac-

tivada.

Para cambiar la conﬁguración de un elemento del menú, selec-

cione el elemento con “+” y “-”. Presione “OK”.

Cuando aparezca el símbolo de “Parámetro editable”, podrá cam-

biar la conﬁguración del elemento con “+” y “-”. Presione “OK”

para guardar la conﬁguración.

Para salir del menú estándar, presione “Menú”. Aparecerá la vi-

sualización estándar.

6.3.1 Temporizador corto de 120 minutos (Pro4)

Con el temporizador corto de 120 minutos, puede activar el modo

confort durante un tiempo seleccionado de hasta 120 minutos.

Durante este tiempo seleccionado, el calentador calienta hasta

alcanzar la temperatura de confort establecida. Después de esto,

el calentador funciona en modo nocturno.

f Si desea utilizar el temporizador corto de 120 minutos, selec-

cione el programa Pro4 del menú estándar.

D0000075531

La visualización estándar muestra el tiempo seleccionado en mi-

nutos y el símbolo “Parámetro editable”. Usando los botones “+”

y “-”, puede seleccionar cualquier período de tiempo de 10 a 120

minutos.

Para activar el temporizador corto, presione “OK”. El calentador

cambia a modo confort hasta que ﬁnalice el tiempo seleccionado.

La visualización de los minutos parpadea durante este período.

Si desea detener el temporizador corto, mantenga presionado

“OK” por más de 3 segundos.

La page est en cours de chargement...

STIEBEL ELTRON CON 100-300 Manuel utilisateur

Marque: STIEBEL ELTRON

Modèle: CON 100-300

Catégorie: Chauffe-eau

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: STIEBEL ELTRON CON 100-300 User manual
español: STIEBEL ELTRON CON 100-300 Manual de usuario

STIEBEL ELTRON CON 100-300 Manuel utilisateur

STIEBEL ELTRON CON 100-300 Manuel utilisateur

dans d''autres langues

Documents connexes