Little GIANT 10EC-CIA-SFS Guide d'installation

Marque: Little GIANT

Modèle: 10EC-CIA-SFS

Catégorie: Pompes à eau

Taper: Guide d'installation

Ce manuel convient également à

6EC-CIA-SFS

6EC-CIA-RF

6EC-CIM

10EC-CIA-SFS

10EC-CIA-RF

10EC-CIM

Installation Guide

Table of Contents

SAFETY INSTRUCTIONS - - - - - - - - - - - - - 2

INTRODUCTION - - - - - - - - - - - - - - - - 4

Product Description - - - - - - - - - - - - - 4

Specifications - - - - - - - - - - - - - - - - 4

Pump Performance Curves - - - - - - - - - - 4

INSTALLATION - - - - - - - - - - - - - - - - - 5

Physical Installation - - - - - - - - - - - - - 5

Electrical Connections - - - - - - - - - - - - 7

OPERATION TESTING - - - - - - - - - - - - - - 8

MAINTENANCE - - - - - - - - - - - - - - - - - 10

Periodic Service - - - - - - - - - - - - - - - 10

Troubleshooting - - - - - - - - - - - - - - - 11

Replacement parts - - - - - - - - - - - - - - 12

LIMITED WARRANTY - - - - - - - - - - - - - - 13

SAFETY INSTRUCTIONS

Hazard Messages

SAFETY INSTRUCTIONS

Hazard Messages

This manual includes safety precautions and other import-

ant information in the following formats:

IMPORTANT: Identifies information that controls correct

assembly and operation of the product.

NOTE: Identifies helpful or clarifying inf

ormation.

This symbol alerts the user to the presence of dan-

gerous voltage inside the product that might cause

harm or electrical shock.

This symbol alerts the user to the presence of hot

surfaces that might cause fire or personal injury.

Before Getting Started

This equipment should be installed and serviced by techni-

cally qualified personnel. Failure to comply with national

and local electrical and plumbing codes and within Fr

anklin

Electric recommendations may result in electrical shock or

fire hazard, unsatisfactory performance, or equipment fail-

ure.

Know the product’s application, limitations, and potential

hazar

ds. Read and f

ollow instructions carefully to avoid

injury and property damage. Do not disassemble or repair

unit unless described in this manual.

Refer to product data plate(s) for additional precautions,

oper

ating instructions and specifications.

Failure to follow installation/operation procedures and all

applicable codes may result in the following hazards:

Indicates an imminently hazardous situation

which, if not avoided, will result in death or

serious injury.

Indicates a potentially hazardous situation

which, if not avoided, could result in death or

serious injury.

Indicates a potentially hazardous situation

which, if not avoided, could result in minor or

moderate personal injury.

Indicates a potentially hazardous situation

which, if not avoided could result in damage to

equipment or other property.

Risk of death, personal injury, or

property damage due to explosion, fire,

or electric shock.

• Do not use to pump flammable or explosive fluids

such as gasoline, fuel oil, kerosene, etc.

• Do not use in explosive atmospheres or hazardous

locations as classified by the NEC, ANSI/NFPA70.

• Do not handle a pump or pump motor with wet hands

or when standing on a wet or damp surface, or in

water.

• When a pump is in its application, do not touch the

motor, pipes, or water until the unit is unplugged or

electrically disconnected.

• If the power disconnect is out of site, lock it in the

open position and tag it to prevent unexpected appli-

cation of power.

• If the disconnect panel is not accessible, contact the

electric company to stop service.

SAFETY INSTRUCTIONS

Before Getting Started

High voltages capable of causing severe

injury or death by electrical shock are

present in this unit.

• To reduce risk of electrical shock, disconnect power

before working on or around the system. More than

one disconnect switch may be required to de-ener-

gize the equipment before servicing.

• This product is supplied with a grounding conductor

and grounding-type attachment plug. To reduce risk

of electric shock, be certain that it is connected only

to a properly grounded grounding-type receptacle.

Do not remove the third prong from the plug. The

third prong is to ground the pump to help prevent

possible electric shock hazard. Do not use an exten-

sion cord.

• Check electrical outlets with a circuit analyzer to

ensure power, neutral, and ground wires are properly

connected. If not, a qualified, licensed electrician

should correct the problem.

• Wire pump system for correct voltages.

• The pump has been evaluated for use with water

only. Pump should only be used with liquids compati-

ble with pump component materials. If the pump is

used with liquids incompatible with the pump com-

ponents, the liquid can cause failure to the electrical

insulation system resulting in electrical shock.

Risk of damage to pump or other equipment.

• Do not use this pump for pumping sea water, bever-

ages, acids, chemical solutions, or any other liquid

that promotes corrosion as this can result in damage

to the pump.

• Do not run pump dry. For optimal cooling and to pro-

long the motor life, the liquid level being pumped

should normally be above the top of the pump hous-

ing.

• This pump is not suitable for pond applications.

Risk of bodily injury, electric shock,

or equipment damage.

• This equipment must not be used by children or per-

sons with reduced physical, sensory or mental abili-

ties, or lacking in experience and expertise, unless

supervised or instructed. Children may not use the

equipment, nor may they play with the unit or in the

immediate vicinity.

• Equipment can start automatically. Always unplug

the pump power cord and disconnect the electrical

power before servicing the pump or switch.

• An inoperative or malfunctioning pump could lead to

flooding, resulting in personal injury or property

damage.

• In applications where property damage and/or per-

sonal injury might result from an inoperative or leak-

ing pump due to power outages, discharge line

blockage, or any other reason, an automatic back-up

system and/or an alarm should be installed.

• Do not run the pump dry. If run dry, the surface tem-

perature of the pump will rise to a high temperature

that could cause skin burns if touched and will cause

serious damage to the pump.

• Do not oil the motor. The pump’s motor housing is

sealed, and contains a high-grade dielectric oil for

heat transfer and lifetime lubrication. Use of other

oils could cause serious electric shock and/or perma-

nent damage to the pump.

• Operation of this equipment requires detailed instal-

lation and operation instructions provided in this

manual for use with this product. Read entire manual

before starting installation and operation.

• End User should receive and retain manual for future

use.

• Keep safety labels clean and in good condition.

• Keep work area clean, well-lit, and uncluttered.

• Wear safety glasses while installing or performing

maintenance on the pump.

• Do not wear loose clothing, jewelry, or anything that

may be caught in the rotating parts. Tie up long hair

and remove jewelry.

INTRODUCTION

Product Description

INTRODUCTION

Product Description

This submersible pump is for use in basins or lift stations and is suitable for pumping clear water or

effluent gray water with up to 1/2" spherical semi-solids. Do not use the pump in applications

where sewage or any other debris (gravel, sand, floating debris, etc.), abrasives, or corrosives are

present.

This product has been carefully tested, inspected, and packaged to ensure safe delivery and opera-

tion. Please examine your item(s) carefully to ensure that no damage occurred during shipment. If

damage has oc

curr

ed, please contact the place of purchase. They will assist you in replacement or

repair, if required.

The pump motor is equipped with an automatic resetting thermal protector and may restart unex-

pectedly. Protector tripping is an indication of motor overloading/overheating, which can be

caused b

y applica

tion issues such as an obstructed pump impeller, switch stuck in the ON position,

pump running dry, pump air-locked, pump short cycling, excessively high or low voltage supply, or

possibly a pump, motor, bearings or seal that have reached the end of their useful life.

Specifications

Pump Performance Curves

6EC 10EC

Gallons/Liters per Minute, at Height

Height 5 ft

1.5 m

10 ft

3 m

15 ft

4.5 m

20 ft

6.1 m

30 ft

9.1 m

Shut Off

6EC

53 GPM 50 GPM 42 GPM 34 GPM

–

28 feet

8.5 meters

201 LPM 189 LPM 159 LPM 129 LPM

10EC

67 GPM 57 GPM 47 GPM 42 24 GPM 36 feet

11 meters

254 LPM 216 LPM 178 LPM 159 LPM 91 LPM

INSTALLATION

Physical Installation

INSTALLATION

Physical Installation

1. Pump must be installed in a suitable gas-tight basin that is at least 18" in diameter and 24"

deep and vented in accordance with local plumbing codes.

2. Clean any debris from the basin and set the pump in the center of the basin (refer to

“Typical

Installation” on page 6). A solid bottom will prevent clogging of the pump from sand and dirt.

3. The pump must be placed on a hard, level surface. Never place the pump directly on clay, earth

or gra

vel surfaces. These surfaces contain small stones, gravel, sand etc. that may clog or dam-

age the pump and cause pump failure.

4. Do not attempt to restrict the intake side of these pumps. Restricting the intake may cause

damage t

o the seal and may starve the pump. If reduced flow rates are required, place a valve

on the discharge side of the pump. Or, if flexible vinyl tubing is used, a clamp can be used on

the tubing to restrict the flow.

5. Connect discharge piping. Use pipe joint compound at all connections. Sump pumps can be

piped t

o dischar

ge into the house drainage system, to a dry well, splash block, or to a storm

drain, depending on local plumbing codes. The discharge pipe should be as short as possible

and contain as few elbows as possible. The discharge pipe should be the same diameter as the

discharge size to reduce pipe friction losses. A smaller pipe will restrict capacity and reduce

pump performance. The pump comes with a 1-1/2" female pipe thread discharge.

• Support the pump and piping while assembling and when installed. Failure to do so may

cause the piping t

o break, the pump to fail, motor bearing failures, etc.

• Always install a union in the discharge line just above the basin cover to allow for easy

removal of the pump for cleaning or repair.

6. A check valve must be used in the discharge line to prevent backflow of liquid into the basin.

The check v

alv

e should be a free-flow valve that will easily pass solids.

Risk of severe injury or death by electrical shock.

• Always disconnect the electrical power before touching the pump or discharge.

• Check local electrical and building codes before installation. The installation must be in

accordance with their regulations as well as the most recent National Electrical Code (NEC).

Risk of property damage due to flooding.

• Do not install the check valve in a vertical position, as solids may settle in the valve and pre-

vent the valve from opening on start-up. For best performance of the check valve when

handling solids, install it in a horizontal position or at an angle of no more than 45°.

• When a check valve is used, drill a relief hole (1/8" or 3/16" in diameter) in the discharge

pipe. This hole should be located below the floor line between the pump discharge and the

check valve. Unless such a relief hole is provided, the pump could “air lock” and will not

pump water even though it will run.

INSTALLATION

Physical Installation

7. Tape the pump and switch cords to the discharge line with electrical tape. This will protect the

cord from damage.

8. Test the operation of the pump system by following the instructions in

“Operation Testing” on

page 8 of this manual. Do not attempt to operate the pump without water; this will damage

the seals and bearings and could result in permanent damage to the pump.

9. Place cover over basin. This cover will help prevent debris from entering the pit and will guard

agains

t ac

cidental injury.

Typical Installation

INSTALLATION

Electrical Connections

Check the pump label for proper voltage required. Do not connect to voltage other than that

shown.

A ground fault circuit interrupter (GFCI) is required.

The pump should be connected or wired to its own circuit, with no other outlets or equipment in

the cir

cuit line. The fuses and circuit breaker should be of ample capacity in the electrical circuit.

The 6EC-CIA-RF and 10EC-CIA-RF pumps have automatic switches with piggyback plugs on the

switch cords. For automatic operation, plug the pump cord into the float switch cord. Plug the float

switch cord (with pump cord attached) into the GFCI outlet.

Pump HP Voltage Breaker Amps

6EC 1/3 115 V 15 A

10EC 1/2 115 V 15 A

Risk of severe injury or death by electrical shock.

• Always disconnect the electrical power before touching the pump or discharge.

• Check local electrical and building codes before installation. The installation must be in

accordance with their regulations as well as the most recent National Electrical Code (NEC).

• The flexible jacketed cord assembly mounted to the pump must not be modified in any way,

with the exception of shortening the cord to fit into a control panel. Any splice between the

pump and the control panel must be made within a junction box mounted outside of the

basin and comply with the National Electrical Code. Employ a licensed electrician.

• Do not use the power cord for lifting the pump.

• Do not remove the third prong from the plug, or cut plug from cord. These actions will void

the warranty.

• Do not use an extension cord.

OPERATION TESTING

Testing Automatic Pump Operation

OPERATION TESTING

If the pump does not operate properly, consult “Troubleshooting” on page 11. If the solution still

cannot be found, please contact the place of purchase or an authorized service center.

Do not let the unit run dry (without liquid). It is designed to be cooled by pumping fluid. The seal

y be damaged and the motor ma

y fail if the pump is allowed to run dry.

If the unit is going to be idle for a period of time, follow the cleaning instructions outlined in the

xt section. Do not let the unit fr

eeze. This may cause cracking or distortion that may destroy the

unit.

Testing Automatic Pump Operation

The 6EC-CIA-SFS and 10EC-CIA-SFS automatic pumps are equipped with an integral float-oper-

ated mechanical switch. Automatic operation is achieved through the pump cord.

The 6EC-CIA-RF and 10EC-CIA-RF pumps have automatic switches with piggyback plugs on the

witch c

ords. The pump must be plugged into piggyback switch cord for automatic operation.

When these pumps are installed in a basin with a sealed cover, switch operation cannot be

observ

ed. The basin co

ver will usually have a spare hole that is plugged with a rubber plug. This

plug can be removed and switch operation can be observed.

To test system operation, follow these steps:

1. Plug the power cord into a grounded receptacle with voltage consistent with the pump volt-

age, as indicated on the pump nameplate.

2. Be sure the gate valve in the discharge line is open.

3. Run water into the basin until the pump is activated.

Do not attempt to run the pump without water; this could result in permanent damage to the

pump

4. C

onfirm that the pump and its control switch are functioning as intended.

5. Confirm that the ON/OFF levels are within specification, and c

onfirm that no potential obstruc-

tions exist that could inhibit switch operation.

6. Confirm that there are no leaks in the pump discharge plumbing and main home drain pipe

plumbing.

Note: It is normal f

or a str

eam of water to spray from the air bleed hole in the pump’s plumbing.

(Water sprays out of a hole by a bolt on the base of the unit.) Confirm that this spray is captured

within the basin.

7. Allow the pump to operate through several on/off cycles.

Risk of damage to pump or other equipment.

• Do not attempt to run the pump without water; this could result in permanent damage to

the pump.

• If pump is run dry, it may damage pump and will void the warranty.

OPERATION TESTING

Testing Manual Pump Operation

The 6EC-CIM and 10EC-CIM manual pumps do not include an automatic liquid level control. The

pump cord for these pumps can be plugged directly into a properly grounded receptacle with volt-

age consistent with the pump nameplate for continuous pump operation.

For automatic operation of a manual pump, a separate float switch or other liquid level control may

be used. If a floa

t swit

ch or level control has been added, refer to

“Testing Automatic Pump Opera-

tion” on page 8 for testing operation.

To test manual pump operation, follow these steps:

1. Connect a discharge hose to the pump’s discharge port.

2. Place pump into a basin or test reservoir.

3. Direct the opposite end of the discharge hose back into the basin or test reservoir so that the

er discharged from the hose during testing will be contained within the basin or test reser-

voir. Secure the hose to prevent the water pressure created during testing from causing the

hose t

o exit the basin or t

est reservoir.

4. If there is a valve on the discharge hose, be sure the valve is open.

5. Using a separate water source, fill the basin or test reservoir until the pump is fully submerged.

Do not attempt to run the pump without water; this could result in permanent damage to the

pump

Do not ov

erfill the basin or test reservoir.

6. Plug the pump’s power cord into a ground fault circuit interrupter (GFCI) receptacle with volt-

age consistent with the pump voltage, as indicated on the pump nameplate.

7. Confirm that the pump is functioning as intended.

Note: It is normal f

or a stream of water to spray from the air bleed hole in the pump’s plumbing.

(Water sprays out of a hole by a bolt on the base of the unit.) Confirm that this spray is captured

within the basin.

8. If pump is not functioning as intended, unplug the pump’s power cord from the receptacle and

efer to “Troubleshooting” on page 11. If the solution still cannot be found, please contact the

place of purchase or an authorized service center.

9. If the pump is functioning as intended, unplug the pump’s power cord from the receptacle

bef

ore attempting to remove it from the basin or test reservoir.

Risk of bodily injury or damage to pump or other equipment.

• Manual, continuous pump operation should be used only for emergencies, or when a large

volume of water is to be pumped. The pump must be continuously monitored during opera-

tion and disconnected from power before the pump runs dry.

• If an accessory float switch or other liquid level control is installed, refer to manufacturer’s

instructions. Failure to install control in compliance with national and local electrical and

plumbing codes and within manufacturer’s recommendations may result in electrical shock

or fire hazard, unsatisfactory performance, or equipment failure.

MAINTENANCE

Periodic Service

MAINTENANCE

Periodic Service

Inspect and test the pump system condition and operation every three months—more frequently in

heavy use applications.

Let pump cool for a minimum of 2 hours before attempting to service. Submersible pumps contain

oil tha

t becomes pr

essurized and hot under normal operating conditions.

1. Check the power cords and electrical outlet for damage or corrosion. The power cord on these

units cannot be r

eplaced. In case of damage

, the whole unit must be replaced.

2. Remove all debris (gravel, sand, floating debris, etc.) from the basin.

3. Check the pump system components (basin, pump, switch, etc.) for any build-up (sludge, sed-

iment, minerals, etc.) that would inhibit functionality of the c

omponents. If significant, remo

build-up or replace affected components.

4. Confirm that all flexible coupling hose clamps are fully engaged with plumbing and fully tight-

ened.

5. Test operation of the pump system. Refer to

“Operation Testing” on page 8.

6. While the pump is running, make sure a stream of water is escaping from the air bleed hole. If

not, clear the hole of any deposits or debris.

Cleaning Impeller and Volute

Periodic cleaning of the pump parts will prolong the life and efficiency of the pump. Refer to the

assembly and disassembly of the pumping head.

1. Remove the five screws that hold the base to the volute, then separate the base from the

olute

. Do not remove the motor housing cover.

2. Remove the base and clean the impeller and the volute passage. Do not use strong solvents on

the impeller

. Do not remo

ve the impeller.

3. Be sure the impeller turns freely after cleaning.

4. Attach the base to the volute and secure it with the five screws.

Risk of severe injury or death by electrical shock, high temperatures, or

pressurized fluids.

• Always unplug the pump power cord in addition to removing the fuse or shutting off the cir-

cuit breaker before working on the pump or switch.

• Let pump cool for a minimum of 2 hours before attempting to service. Submersible pumps

contain oil that becomes pressurized and hot under normal operating conditions.

Risk of damage to pump or other equipment.

• This unit is permanently lubricated. Oiling is not required. Do not open the sealed portion of

the unit or remove housing screws.

• Do not remove the motor housing cover.

• Do not remove the impeller

• Warranty is void if the motor housing cover, impeller, or seals have been removed. Repairs

on the motor or impeller require special tools.

MAINTENANCE

Troubleshooting

Problem Probable Causes Corrective Action

Pump does not turn on

Pump not plugged in. Plug in pump.

Circuit breaker off or fuse removed. Turn on circuit breaker or replace fuse.

Accumulation of trash on float. Clean float.

Float obstruction. Check float path and provide clearance.

Defective switch. Replace switch.

Defective motor. Replace pump.

Pump will not shut off

Float or float rod obstruction. Check float and float rod path and provide clearance.

Pump is air locked. Remove pump and clean air bleed hole.

Liquid inflow matches pump capacity. Larger pump required.

Defective switch. Replace switch.

Pump runs but does not

discharge liquid

Check valve installed backwards. Check flow indicating arrow on check valve body to ensure proper

installation.

Check valve stuck or plugged. Remove check valve and inspect for proper operation.

Lift too high for pump. Check rated pump performance.

Inlet to impeller plugged. Pull pump and clean.

Pump is air locked. Remove pump and clean air bleed hole.

Pump does not deliver

rated capacity

Lift too high for pump. Check rated pump performance.

Low voltage, speed too slow. Check that supply voltage matches the nameplate rating.

Impeller or discharge pipe is clogged. Pull pump and clean. Check pipe for scale or corrosion.

Impeller wear due to abrasives. Replace pump.

Pump cycles continuously

No check valve in long discharge pipe

allowing liquid to drain back into basin.

Install a check valve in discharge line.

Check valve leaking. Inspect check valve for correct operation.

Basin too small for inflow. Install larger basin.

Water sprays out of a hole

by a bolt on the base of the

unit.

This pump comes with a bleed hole that

allows trapped air to escape from the

pump, preventing air lock.

Water spraying out of this hole is com-

pletely normal.

No corrective action is required.

MAINTENANCE

Replacement parts

Number Part Number Description

110970101

Cover Assembly, 115 V, Automatic, with Switch, 20' Cord

1 110970102 Cover Assembly, 230 V, Automatic, with Switch, 20' Cord

1 110970103 Cover Assembly, 115 V, Manual, 20' Cord

1 110970104 Cover Assembly, 230 V, Manual, 20' Cord

2 110970201 Capacitor kit, 115 V, with Bracket, Seal Ring

2 110970202 Capacitor kit, 230 V, with Bracket, Seal Ring

3 110970301 Float Assembly with Stem Strap

4 110970401 Volute Base, Plastic, with Gasket

4 110970402 Volute Base, Cast Iron, with Gasket

5 599118 Remote Float Switch, 10' Cord, 115/230 V

5 599210 Remote Float Switch, 20' Cord, 115/230 V

SEWAGE & EFFLUENT 2 YEAR WARRANTY STATEMENT

LIMITED WARRANTY

THIS WARRANTY SETS FORTH THE COMPANY’S SOLE OBLIGATION AND PURCHASER’S EXCLUSIVE REMEDY FOR DEFECTIVE PRODUCT.

Franklin Electric Company, Inc. and its subsidiaries (hereafter “the Company”) warrants that the products accompanied by this warranty are

free from defects in materials or workmanship of the Company that exist at the time of sale by the Company and which occur or exist within the

applicable warranty period. Any distributor, sub-distributor, recipient, end-user and/or consumer agrees that by accepting the receipt of the

products, the distributor, sub-distributor, recipient, end user and/or consumer expressly agrees to be bound by the terms of the warranty set

forth herein.

I. Applicable Warranty Period

The products accompanied by this warranty shall be covered by this Limited Warranty for a period of 24 months from the date of original

purchase by the consumer. In the absence of suitable proof of purchase date, the warranty period of this product will begin to run on the

product's date of manufacture.

II. Instructions Applicable to this Limited Warranty

1. Consumers wishing to submit a warranty claim must return the products accompanied by this warranty to the point of purchase for

warranty consideration.

2. Upon discovery of a defect, any personal injury, property damage or any other type of resulting damage, if applicable, shall be reason-

ably mitigated to the extent possible.

3. At its discretion, the Company may inspect products either at its facilities or in the field, and after determination of a warranty claim,

will, at its option, repair or replace defective parts. Repaired or replaced parts will be returned freight prepaid by the Company.

4. This warranty policy does not cover any labor or shipping charges. The Company shall not be liable for any costs or charges attribut-

able to any product testing, maintenance, installation, repair or removal, or for any tools, supplies, or equipment needed to install,

repair, or remove any product.

III. Limitations Applicable to this Limited Warranty

THIS WARRANTY DOES NOT APPLY TO ANY OF THE FOLLOWING:

1. Brushes, impeller or cam on models with brush-type motors and/or flex-vane impellers.

2. Any product that is not installed, applied, maintained, and used in accordance with the Company's published instructions, applicable

codes, applicable ordinances and/or with generally accepted industry standards.

3. Any product that has been subject to misuse, misapplication, neglect, alteration, accident, abuse, tampering, acts of God (including

lightning), acts of terrorism, acts of war, fire, improper storage or installation, improper use, improper maintenance or repair, damage

or casualty, or to an excess of the recommended maximums as set forth in the product instructions.

4. Any product that is operated with any accessory, equipment, component, or part not specifically approved by the Company.

5. Use of replacement parts not sold by the Company, the unauthorized addition of non-Company products to other Company products,

and the unauthorized alteration of Company products.

6. Products damaged by normal wear and tear, normal maintenance services and the parts used in connection with such service, or any

other conditions beyond the control of the Company.

7. Any product that has been used for purposes other than those for which it was designed and manufactured.

8. Any use of the product where installation instructions and/or instructions for use were not followed.

9. Products connected to voltage other than indicated on nameplate.

10. Products where the pump was exposed to any of the following: sand, gravel, cement, grease, plaster, mud, tar, hydrocarbons, hydro-

carbon derivatives (oil, gasoline, solvents, etc.) or other abrasive or corrosive substances.

11. Products in which the pump has been used for pumping of liquids above 140 °F.

12. Products in which the pump was allowed to operate dry (fluid supply cut off).

13. Products in which the sealed motor housing has been opened or the product has been otherwise dismantled by customer.

14. Products in which the cord has been cut to a length of less than three feet.

The Company reserves the right at any time, and from time to time, to make changes in the design and/or improvements upon its product with-

out thereby imposing any obligation upon itself to make corresponding changes or improvements in or upon its products already manufactured

and/or previously sold. The Company further reserves the right to substitute parts or components of substantially equal quality in any warranty

service required by operation of this Limited Warranty.

This written Limited Warranty is the entire warranty authorized and offered by the Company. There are no warranties or representations

beyond those expressed in this document.

THIS WARRANTY AND REMEDY IS IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES INCLUDING WITHOUT LIMITATION, WARRANTIES OF

MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY SPECIFICALLY DISCLAIMED AND EXPRESSLY

EXCLUDED. CORRECTION OF NON-CONFORMITIES, IN THE MANNER AND FOR THE PERIOD OF TIME AS SET FORTH ABOVE, SHALL CONSTI-

TUTE FULFILLMENT OF ALL LIABILITY OF THE COMPANY TO THE PURCHASER WHETHER BASED ON CONTRACT, NEGLIGENCE, OR OTHERWISE.

THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES SUCH AS, BUT NOT LIMITED TO:

DAMAGE TO OR LOSS OF OTHER PROPERTY OR EQUIPMENT, LOSS OF USE OF EQUIPMENT, FACILITIES OR SERVICE, LOSS OF PROFIT OR

SALES, COST OF PURCHASES OR REPLACEMENT GOODS, CLAIMS OF CUSTOMERS OF THE PURCHASER, FAILURE TO WARN AND/OR

INSTRUCT, LOSS OF OTHER PRODUCTS, OR COSTS OF ENVIRONMENTAL REMEDIATION, OR DIMINUTION IN PROPERTY VALUE. THE REME-

DIES OF THE PURCHASER SET FORTH HEREIN ARE EXCLUSIVE, AND THE LIABILITY OF THE COMPANY SHALL NOT, EXCEPT AS EXPRESSLY

PROVIDED HEREIN, EXCEED THE PRICE OF THE PRODUCTS UPON WHICH SUCH LIABILITY IS BASED. DAMAGES AS SET FORTH IN THIS

PARAGRAPH SHALL BE REASONABLY MITIGATED TO THE EXTENT POSSIBLE. THIS PARAGRAPH SHALL ALSO APPLY TO ALL DAMAGES

RESULTING FROM CONDITIONS SET FORTH IN SECTION III ABOVE AND (1) DEFECTS IN PRODUCT PROTOTYPES OR REPLACEMENT PART

PROTOTYPES THAT HAVE NOT BEEN PUT INTO PRODUCTION, CIRCULATED AND SOLD BY THE COMPANY, AND/OR (2) DEFECTS THAT WERE

NOT FOUND AT THE TIME OF SALE DUE TO SCIENTIFIC AND TECHNOLOGICAL REASONS.

This Limited Warranty gives you specific legal rights. You may have other rights, which vary according to the applicable laws and regula-

tions. Where any term of this warranty is prohibited by such laws, it shall be null and void, but the remainder of this warranty shall remain

in full force and effect.

DISCLAIMER: Any oral statements about the product made by the seller, the Company, the representatives or any other parties, do not constitute

warranties, shall not be relied upon by the user, and are not part of the contract for sale. Seller’s and the Company’s only obligation, and buyer’s

only remedy, shall be the replacement and/or repair by the Company of the product as described above. Before using, the user shall determine

the suitability of the product for his intended use, and user assumes all risk and liability whatsoever in connection therewith.

Form 998913

Rev. 002

11-18

Franklin Electric Co., Inc.

Oklahoma City, OK 73157-2010

Phone: 1-800-701-7894

Fax: 1-405-228-1531

For technical assistance, please contact . . . . . . . . . . . . . . . . . . . 800-701-7894

www.littlegiant.com

lgnet@fele.com

6EC-CIA-SFS

6EC-CIA-RF

6EC-CIM

10EC-CIA-SFS

10EC-CIA-RF

10EC-CIM

Guide d’installation

Table des matières

CONSIGNES DE SÉCURITÉ - - - - - - - - - - - 16

INTRODUCTION - - - - - - - - - - - - - - - - 18

Description du produit - - - - - - - - - - - - 18

Spécifications - - - - - - - - - - - - - - - - 18

Courbes de rendement de la pompe - - - - - 18

INSTALLATION - - - - - - - - - - - - - - - - - 19

Installation Physique - - - - - - - - - - - - - 19

Branchements électriques - - - - - - - - - - 22

TEST DE FONCTIONNEMENT - - - - - - - - - - 23

ENTRETIEN - - - - - - - - - - - - - - - - - - - 25

Service Périodique - - - - - - - - - - - - - - 25

Dépannage - - - - - - - - - - - - - - - - - 26

Pièces de Remplacement - - - - - - - - - - - 27

GARANTIE LIMITÉE - - - - - - - - - - - - - - - 29

CONSIGNES DE SÉCURITÉ

Messages d’alertes

CONSIGNES DE SÉCURITÉ

Messages d’alertes

Ce manuel comprend des précautions de sécurité et

d’autres renseignements importants présentés dans le

format suivant:

IMPORTANT: Présente l’information qui permet un

assemblage et un fonctionnement adéquats du produit.

REMARQUE: Présente de l’inf

ormation utile ou des préci-

sions.

Ce symbole avise l’utilisateur de la présence d’une

tension dangereuse dans le produit présentant un

risque de blessures ou d’électrocution.

Ce symbole avise l’utilisateur de la présence de

surfaces chaudes présentant un risque d’incendie

ou de blessures corporelles.

Avant de Commencer

L'installation et l'entretien de l'équipement doivent être

effectués par un employé techniquement qualifié. Le non-

respect des codes électriques et codes de plomberie local

et national et des recommandations de Franklin Electric

pourrait mener à une électrocution ou un incendie, une

mauvaise performance ou une défaillance de l’équipe-

ment.

Soyez consient(e) de l’application, des limites et des ris-

ques potentiels du produit. Lire et suivre attentivement

ces instructions pour é

viter toute blessure ou tout dom-

mage matériel. Ne pas désassembler ou réparer l’unité,

sauf si c

ela est décrit dans le pr

ésent manuel.

Consulter la plaque signalétique du produit pour obtenir

des ins

tructions, précautions et des spécifications de

onctionnement supplémentaires.

Le non-respect des procédures d’installation/utilisation et

de tous les codes applicables peut entr

aîner les risques

suivants:

Indique une situation dangereuse imminente

qui, si elle n’est pas évitée, entraînera la mort

ou des blessures graves.

Indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, peut

entraîner la mort ou des blessures graves.

Indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, peut

entraîner des blessures corporelles

mineures ou modérées.

Indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, peut

entraîner des dommages à l’équipement ou

matériels.

Risque de mort, de blessure corporelle

ou de dommage

matériel en raison

d’une explosion, d’un incendie ou

d’une électrocution.

• Ne pas utiliser pour pomper des liquides inflamma-

bles ou explosifs comme l’essence, le mazout, le

kérosène, etc.

• Ne pas utiliser dans une atmosphère explosive ou

un emplacement dangereux selon le Code national

de l’électricité, ANSI/NFPA70.

• Ne pas manipuler une pompe ou un moteur de

pompe avec les mains mouillées ou debout sur une

surface humide ou mouillée, ou dans de l’eau.

• Lorsqu’une pompe est en mode de

fonctionnement, ne pas toucher le moteur, les

tuyaux ou l’eau tant que l’unité n’a pas été

débranchée ou déconnectée électriquement.

• Si le dispositif de coupure du circuit d’alimentation

se situe hors site, le verrouiller en position ouverte

et le consigner afin d’empêcher toute mise sous

tension inopinée.

• Si le panneau du disjoncteur n’est pas accessible,

contacter la compagnie d’électricité afin que le

courant soit coupé.

CONSIGNES DE SÉCURITÉ

Avant de Commencer

Cette unité contient des hautes

tensions capables de causer de graves

blessures ou la mort par électrocution.

• Pour réduire le risque de choc électrique, débran-

chez l’alimentation avant de travailler sur le sys-

tème ou autour de celui-ci. Plusieurs interrupteurs

d’isolement peuvent être nécessaires pour

décharger l’équipement avant de procéder à son

entretien.

• Ce produit est fourni avec un conducteur de mise à

la terre et une fiche munie d’une attache de mise à

la terre. Pour réduire le risque de décharge élec-

trique, assurez-vous de seulement brancher la

pompe à une prise électrique correctement mise à

la terre. Ne retirez pas la troisième branche de la

fiche. La troisième branche sert à la mise à la terre

de la pompe, afin de prévenir tout risque possible

de décharge électrique. N’utilisez pas un cordon de

rallonge.

• Vérifier les prises électriques à l’aide d’un

analyseur de circuit pour s’assurer que les fils de

phase, de neutre et de terre sont correctement

branchés. Si ce n’est pas le cas, le problème doit

être corrigé par un électricien qualifié agréé.

• Raccorder le système de pompe en respectant la

tension indiquée.

• La pompe a été évaluée pour être utilisée avec de

l’eau uniquement. La pompe doit être utilisée

uniquement avec des liquides compatibles avec les

matériaux de ses composants. Si la pompe est util-

isée avec des liquides incompatibles avec les com-

posants de la pompe, le liquide peut provoquer une

défaillance du système d'isolation électrique

entraînant un choc électrique.

Risque de dommages à la pompe ou d’autres

équipements.

• Ne pas utiliser la pompe pour pomper de l’eau de

mer, des boissons, de l’acide, des solutions

chimiques ou tout autre liquide qui favoriserait la

corrosion, ce qui pourrait endommager la pompe.

• Ne pas faire tourner la pompe à sec. Pour obtenir

un refroidissement optimal et pour prolonger la

durée de vie de la pompe, le niveau de liquide

pompé doit normalement dépasser le dessus du

boîtier de la pompe.

• Cette pompe n’est pas prévue pour être utilisée

dans un étang.

Risque de blessures corporelles

ou de dommages matériels.

• Cet équipement ne doit pas être utilisé par des

enfants ou des personnes ayant des capacités phy-

siques, sensorielles ou mentales réduites ou un

manque d’expérience, à moins qu’elles ne soient

supervisées ou dirigées. Les enfants ne doivent pas

utiliser l’équipement ni jouer avec le produit ou à

proximité de celui-ci.

• L’équipement peut démarrer automatiquement.

Toujours débrancher le cordon d’alimentation de la

pompe et couper l’alimentation électrique avant

d’entretenir la pompe ou l’interrupteur.

• Une pompe inopérante ou défectueuse pourrait

entraîner une inondation, des blessures corporelles

ou des dommages matériels.

• Dans les applications où des dommages matériels

et/ou des blessures corporelles pourraient découler

du non-fonctionnement ou d’une fuite de la pompe

en raison de pannes de courant, d’une obstruction

de la ligne d’évacuation ou de toute autre raison,

un système de sauvegarde automatique et/ou une

alarme doivent être installés.

• Ne pas faire fonctionner la pompe à sec. En cas de

fonctionnement à sec, la température à la surface

de la pompe augmentera à un niveau susceptible

de causer des brûlures cutanées en cas de contact

et entraînera de graves dommages à votre pompe.

• Ne pas graisser le moteur. Le carter moteur de la

pompe est scellé et renferme une huile diélectrique

de qualité supérieure pour la transmission de chal-

eur et la lubrification à vie. L’utilisation d’autres

huiles peut causer de graves électrocutions et/ou

des dommages permanents de la pompe.

• Le fonctionnement de cet équipement requiert les

instructions d’installation et de fonctionnement

détaillées fournies dans le présent manuel. Lire

tout le manuel avant d’installer et d’utiliser le

produit.

• L’utilisateur final doit recevoir et conserver le

manuel pour consultation ultérieure.

• Garder les étiquettes de sécurité propres et en bon

état.

• Garder la zone de travail propre, bien éclairée et

dégagée.

• Porter des lunettes de sécurité lors de l’installation

ou de l’entretien de la pompe.

• Ne pas porter de vêtements amples, de bijoux ou

tout autre accessoire qui pourrait se prendre dans

les pièces mobiles de l’équipement. Attacher les

cheveux longs et retirer les bijoux.

INTRODUCTION

Description du produit

INTRODUCTION

Description du produit

Cette pompe immergée est prévue pour être utilisée dans des bassins ou des stations de relève-

ment. Elle peut être utilisée pour pomper de l’eau claire ou des effluents eau grise contenant des

semi-solides de forme sphérique jusqu’à 12,

7mm (1/2po) de diamètre. Ne pas utiliser cette pompe

dans des applications où d’autres débris (gravier, sable, débris flottants, etc.), des abrasifs ou des

matières corrosives sont présents.

Ce produit a été soigneusement testé, inspecté et emballé pour en assurer la livraison et le

onctionnement sécuritair

es. Veuillez examiner votre ou vos articles soigneusement afin de vous

assurer qu’aucun dommage ne s’est produit pendant l’expédition. Dans le cas contraire, veuillez

communiquer avec le vendeur. Il vous aidera à obtenir un remplacement ou une réparation, le cas

échéant.

Le moteur de la pompe est muni d’un protecteur thermique à réinitialisation automatique et peut

edémarr

er subitement. Le déclenchement du protecteur est une indication que le moteur est sur-

chargé ou surchauffe, ce qui peut être causé par des problèmes d’application, comme un impulseur

de pompe obs

trué

, un interrupteur coincé en position de mise en marche, une pompe qui

fonctionne à vide, une pompe bloquée par de l’air, un cycle court de pompe, une alimentation à

tension excessivement élevée ou faible, ou possiblement la fin de la durée de vie utile d’une

pompe, d’un moteur, de paliers ou d’un joint d’étanchéité.

Spécifications

Courbes de rendement de la pompe

6EC 10EC

Gallons par minute, à la hauteur/Litres par minute, à la hauteur

La taille 5 pieds

1.5 mètres

10 pieds

3 mètres

15 pieds

4.5 mètres

20 pieds

6.1 mètres

30 pieds

9.1 mètres

Coupure

6EC

53 GPM 50 GPM 42 GPM 34 GPM

–

28 pieds

8.5 mètres

201 LPM 189 LPM 159 LPM 129 LPM

10EC

67 GPM 57 GPM 47 GPM 42 24 GPM 36 pieds

11 mètres

254 LPM 216 LPM 178 LPM 159 LPM 91 LPM

INSTALLATION

Installation Physique

INSTALLATION

Installation Physique

1. La pompe doit être installée dans un bassin étanche au gaz approprié d’au moins 18 po (45,7

cm) de diamètre et 24 po (61,0 cm) de profondeur, et ventilé conformément aux codes locaux

de plomberie.

2. Enlevez tout débris dans le bassin et placez la pompe au centre de ce dernier (se référer à

“Installation Typique” on page 21). Un fond solide empêchera la pompe d’être obstruée par du

sable et des saletés.

3. La pompe doit être placée sur une surface dure et de niveau. Ne placez jamais la pompe

dir

ect

ement sur une surface d’argile, de terre ou de gravier. Ces surfaces comportent de petites

roches, du gravier, du sable, etc., qui peuvent obstruer ou endommager la pompe et provoquer

sa défaillance.

4. N’essayez pas de restreindre le côté prise de ces pompes. La restriction de la prise peut

endommager le joint d’étanchéit

é et sous

-alimenter la pompe. S’il est nécessaire de réduire les

débits, une soupape peut être installée sur le côté refoulement de la pompe. Ou si un tuyau

flexible en vinyle est utilisé, une bride peut être utilisée sur le tuyau pour restreindre le débit.

5. Connectez la tuyauterie de refoulement. Utilisez une pâte à joint de tuyau sur toutes les con-

nexions. Le tuyau de refoulement doit être aussi court que possible et comporter le moins de

oudes possible

. Le tuyau de refoulement doit être du même diamètre que celui du

refoulement, afin de réduire les pertes par frottement. Un tuyau plus petit restreint la capacité

et réduit le rendement de la pompe. La pompe d’égout est livrée avec un refoulement à file-

tage femelle de 1.5 po (38 mm).

• Soutenez la pompe et la tuyauterie au cours de l’assemblage et de l’installation. Un

manquement pourrait entraîner la rupture des tuyaux, la défaillance de la pompe, la

défaillance des paliers du moteur, etc.

• Installez toujours un raccord union dans le conduit de refoulement, juste au-dessus du

couvercle de bassin, afin de permettre le retrait facile de la pompe à des fins de nettoyage

ou de réparation.

Risque de blessure grave ou de mort par électrocution.

• Débranchez toujours l’alimentation électrique avant de toucher à la pompe ou au

refoulement.

• Avant l’installation, vérifiez les codes locaux de l’électricité et du bâtiment. L’installation doit

respecter leur réglementation, de même que le plus récent Code national de l’électricité

(CNE).

INSTALLATION

Installation Physique

6. Un clapet anti-retour doit être utilisé dans le conduit de refoulement pour empêcher un

refoulement du liquide dans le bassin. Le clapet anti-retour doit être une vanne à débit direct

qui laisse facilement passer les solides.

7. Fixez les cordons d’interrupteur et de pompe au conduit de refoulement avec du ruban d’élec-

tricien. Cela aidera à protègera le cordon de tout dommage.

8. Testez le fonctionnement du système en suivant les instructions présentées dans

“Test de

fonctionnement” on page 23 de ce manuel. Ne tentez pas de faire fonctionner la pompe sans

eau; cela endommagerait les joints d’étanchéité et les paliers, et risquerait de provoquer des

dommages permanents à la pompe.

Placez le couvercle par-dessus le bassin. Ce couvercle aide à empêcher des débris d’entrer

dans le bassin et pr

otège c

ontre les blessures accidentelles.

Risque de dommages matériels dus aux inondations.

• N’installez pas le clapet antiretour en position verticale, car des solides peuvent se déposer

dans le clapet d'et empêcher le clapet d'ouverture au moment du démarrage. Pour un

rendement optimal du clapet anti-retour dans la gestion des solides, installez dans une

position horizontale ou à un angle d’au plus 45°.

• Lorsqu’un clapet anti-retour est utilisé, percez un orifice de sûreté (de 1/8 po ou 3/16 po [3,2

mm ou 4,8 mm] de diamètre) dans le tuyau de refoulement. Cet orifice doit être situé sous

le niveau du plancher, entre le refoulement de la pompe et le clapet anti-retour. Si un tel ori-

fice de sûreté n’est pas percé, la pompe peut être « bloquée par de l’air » et ne pas pomper

d’eau, même si elle est en marche.

La page charge ...

Little GIANT 10EC-CIA-SFS Guide d'installation

Marque: Little GIANT

Modèle: 10EC-CIA-SFS

Catégorie: Pompes à eau

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Little GIANT 10EC-CIA-SFS Installation guide
español: Little GIANT 10EC-CIA-SFS Guía de instalación

Little GIANT 10EC-CIA-SFS Guide d'installation

Ce manuel convient également à

Little GIANT 10EC-CIA-SFS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents