Stovax Studio Air Icon XS Guide d'installation

PM1636.3.01.2021

Installation Instructions

Instructions d’installation

Istruzioni per l’Installazione

2

Covering the following models:

Couvrant les modèles suivants:

Per i seguenti modelli:

Inset Convector

Gamme d'inserts

Cassetto da incasso

Appliance Commissioning Sheet..3

Installation Instructions ................ 6

Dimensions ................................................. 6

Distance to Combustibles...........................7

Parts Identifier ............................................9

Pre-Installation..........................................10

Installing the Appliance.............................13

Technical Specification .............................14

Commissioning .........................................23

Reversing The Door .................... 44

Maintenance & Servicing ............ 48

Spare Parts List ........................................ 54

Information Requirement - Solid Fuel .....56

Service Records .......................................59

Studio Air 1 326-018

Studio Air 2 326-031

CONTENTS/ CONTENU/ CONTENUTO

Liste Des Vérifications De Mise

En Service ...................................... 4

Instructions D’installation ............ 6

Dimensions ................................................. 6

Distance Des Matériaux Combustible ........7

Identificateur De Pièces .............................9

Instructions Avant L'installation ................10

Installation D'appareil ...............................24

Liste des vérifications pour l’installation ... 25

Mise En Service .......................................33

Inversion De La Porte ................. 44

Maintenance Et Révision ............ 49

Liste Des Principales Pièces

De Rechange ...........................................54

Fiche produit - Informations à fournir pour

un appareil de chauffage localisé à

combustible solide .................................... 57

Fiches De Maintenance............................59

Elenco Di Controllo Per La Messa

A Punto Dell’apparecchio ............. 5

Istruzioni per l’Installazione .........4

Dimensioni .................................................. 6

Distanze Da Materiali Combustibili ............7

Numero Identificativo Delle Parti ................ 9

Pre-Installazione ...................................... 10

Installazione............................................. 34

Informazioni importanti ............................ 35

Messa A Punto ........................................ 43

Inversione Dello Sportello .......... 44

Manutenzione E Interventi

Di Assistenza ...............................50

Elenco Delle Parti Di Ricambio ............... 54

Scheda del prodotto: richiesta di

informazioni per riscaldatore

combustibile solido per ambienti ............. 58

Registri Degli Interventi Di Assistenza .... 59

GB FR

IT

3

Dealer appliance was purchased from:

Name:

Address:

Telephone number:

Essential information - MUST be completed:

Date Installed:

Model Description:

Serial Number:

Installation Engineer:

Company Name:

Address:

Telephone number:

Commissioning Checks - to be completed and signed:

Is flue system correct for the appliance:

YES NO

Flue swept and soundness test complete:

YES NO

Smoke test completed on installed appliance YES NO

Spillage test completed YES NO

Use of appliance and operation of controls explained YES NO

Clearance to combustible materials checked YES NO

Instruction book handed to customer YES NO

CO Alarm Fitted YES NO

Flue draught Reading (Pa) HOT COLD

Signature: ............................................................................ Print Name: ..........................................................................

To assist us in any guarantee claim please complete the following information:-

APPLIANCE COMMISSIONING SHEET

GB

4

Distributeur où l’appareil a été acheté

Nom :

Adresse :

Numéro de téléphone :

Informations essentielles – Cette section DOIT être remplie:

Date d’installation :

Description du modèle :

Numéro de série :

Technicien installateur:

Nom de la société :

Adresse :

Numéro de téléphone :

Vérifications de mise en service - à remplir et signer:

Le conduit de fumée est approprié à cet appareil OUI NO

Le conduit a été ramoné et le test de vacuité a été effectué. OUI NO

Le test de fumée de l’appareil installé a été effectué OUI NO

Le test d’étanchéité du corps de chauffe a été effectué OUI NO

L’utilisation de l’appareil et le fonctionnement des

commandes ont été expliqués

OUI NO

Les distances aux matériaux combustibles ont été vérifiées OUI NO

Le manuel d’instructions a été remis au client OUI NO

Le détecteur-avertisseur de CO a été installé

(recommandé)

OUI NO

Lecture du tirage du conduit (Pa) CHAUD FROID

Signature: ............................................................................ Nom en majuscules: .....................................................

Pour faciliter les démarches de dédommagement sous garantie, veuillez fournir les informations suivantes :-

LISTE DES VÉRIFICATIONS DE MISE EN SERVICE

FR

5

L’apparecchio è stato acquistato presso:

Nome:

Indirizzo:

Numero di telefono:

Dati obbligatori – DEVONO essere inseriti:

Data di installazione:

Descrizione del modello:

Numero di serie:

Tecnico installatore:

Nome azienda:

Indirizzo:

Numero di telefono:

Controlli di messa a punto (da compilare e firmare):

Il sistema della canna fumaria è adatto all’apparecchio:

SÌ NO

Controllo della pulizia e dello stato della canna fumaria completato:

SÌ NO

Controllo fumi sull’apparecchio installato completato: SÌ NO

Controllo versamenti completato: SÌ NO

Utilizzo dell’apparecchio e svolgimento dei controlli spiegato: SÌ NO

Spazio libero dai materiali combustibili controllato: SÌ NO

Manuale di istruzioni consegnato al cliente SÌ NO

Allarme di monossido di carbonio installato SÌ NO

Lettura del tiraggio del canale da fumo (Pa) CALDO FREDDO

Nome in stampatello: ................................................................ Firma:...........................................................................

La compilazione del modulo seguente sarà utile in caso di interventi in garanzia.

ELENCO DI CONTROLLO PER LA MESSA A PUNTO DELL’APPARECCHIO

IT

6

DIMENSIONS/ DIMENSIONI

All dimensions in mm/Toutes les dimensions sont en mm/ Tutte le dimensioni in mm

* Edge Frame/ Bord du carter/ Cornice bordo

A B C D E F G H I J K* L* M N O P

Studio Air 1

783 450 348 855 492 244 480 152 171 240 779 450 259 590 100 40

Studio Air 2 983 476 348 1055 518 244 611 152 171 240 979 476 284 790

100 40

A

G

B

J

C

L

M

E

F

K

N

I External Diameter Ø

I Diamètre extérieur Ø

I diametro esterna Ø

D

O Air Duct Diameter Ø

O Diamètre de la conduite d'air Ø

O diametro del condotto dell'aria Ø

H Internal Diameter Ø

H Diamètre intérieur Ø

H diametro interno Ø

P

A1 A2 B C D1 D2 E

Studio Air 1

389 389 311 71 389 389 160.5

Studio Air 2

489 489 311 71 489 489 160.5

A1

A2

B

100mm Ø

C

D1

D2

E

EXTERNAL AIR/D'AIR EXTÉRIEUR/VENTILAZIONE ESTERNA

7

B

A

C

B

A

C

D

Void/ Vacant/ Vuoto

No Combustible Material in this area

Pas de matériau combustible dans cette zone

Non posizionare il materiale combustibile in

quest'area

MINIMUM DISTANCE TO COMBUSTIBLE MATERIAL

DISTANCE DES MATÉRIAUX COMBUSTIBLE

DISTANZA MINIMA DAL MATERIALE FIAMMABILE

CLEARANCE TO COMBUSTIBLE MATERIAL/ DISTANCE DES MATÉRIAUX

COMBUSTIBLE/ DISTANZA MINIMA DAL MATERIALE FIAMMABILE

DIMENSIONS/DIMENSIONI (MM) A B C D

Studio Air 1 10 85 240 500

Studio Air 2 10 85 290 800

8

HEARTH DIMENSIONS/ DIMENSIONS DE L'ÂTRE / DIMENSIONI FOCOLARE

DIMENSIONS/DIMENSIONI (MM)

A

(Min)

B

Studio Air 1 500 1281

Studio Air 2 700 1581

B

*A

*Stovax recommends that the depth

of the Decorative Hearth is equal

to or greater than the height of the

appliance from the floor, OR, the

length of the door from the wall when

in the open position.

USE WHICHEVER FIGURE IS

GREATER.

*Stovax recommande une profondeur

d’âtre décoratif égale ou supérieure

à la hauteur de l’appareil à partir du

sol OU à la longueur de la porte en

position ouverte.

UTILISER LA TAILLE MA PLUS

GRANDE.

*Stovax consiglia che la profondità

del Focolare Decorativo sia uguale o

maggiore dell'altezza dell'apparecchio

dal pavimento, OPPURE, della

lunghezza dello sportello dalla parete

quando è in posizione aperta.

SCEGLIERE IL NUMERO MAGGIORE

TRA I DUE.

125mm hearth thickness

(Constructional and Decorative combined)

Épaisseur de l’âtre 125 mm

(Parties construite et décorative combinées)

Spessore del focolare 125 mm

(focolare di costruzione più focolare decorativo)

12mm thick Decorative hearth/

Âtre décoratif 12 mm d’épaisseur/

Focolare decorativo spesso 12 mm

If installed at a height above 600mm from the floor there is no need for

a constructional hearth in front of the appliance.

Si l’appareil est installé à 600 mm au-dessus du sol, il est inutile de

construire un âtre devant.

In caso di installazione a un'altezza maggiore di 600 mm dal pavimento

non è necessario il focolare di costruzione davanti all'apparecchio.

Unprotected

Combustible Material/

Matériau inflammable

non protégé/

Materiale infiammabile

non protetto

Protected Combustible

Material/

Matériau inflammable

protégé/

Materiale infiammabile

protetto

3 x D Ø

1.5 x D Ø

GB: Make sure that the connected flue system is positioned at a

reasonable distance from any combustible material

Stovax recommend the use of a flue liner when installing into a

masonry chimney. Alternative methods can be used if the chimney

is sound and correctly sized, however access may be required to

make an effective seal - ie Using a sump adapter.

Stovax recommend using an approved twin wall insulated chimney

system when installing within studwork.

FR: Veiller à ce que le système de conduit raccordé soit placé à une

distance raisonnable du matériau inflammable

Stovax recommande l'utilisation d'un boisseau pour l’installation

dans une cheminée en maçonnerie. D’autres méthodes peuvent

être utilisées si la cheminée est en bon état et bien dimensionnée.

Toutefois, un accès est nécessaire pour un scellage efficace c’est-

à-dire avec une plaque d’étanchéité.

Stovax recommande l’utilisation d'un système de cheminée à

double paroi d’isolation pour l’installation dans une ossature

murale.

CLEARANCE TO COMBUSTIBLE MATERIAL/ DISTANCE DES MATÉRIAUX

COMBUSTIBLE/ DISTANZA DAI MATERIALI COMBUSTIBILI

CLEARANCE TO COMBUSTIBLE MATERIAL/ DISTANCE DES MATÉRIAUX

COMBUSTIBLE/ DISTANZE DA MATERIALI COMBUSTIBILI

IT: Assicurarsi che il sistema del canale da fumo collegato sia

posizionato a una distanza ragionevole da eventuali materiali

infiammabili

Stovax raccomanda l'uso di un condotto interno quando si installa

una canna fumaria in muratura. Si possono utilizzare metodi

alternativi se la canna fumaria è posizionata e dimensionata

correttamente, sebbene potrebbe essere necessario un accesso

per ottenere una tenuta efficace - ad es. utilizzando un adattatore

per il canale.

Stovax raccomanda l'utilizzo di un sistema di canna fumaria isolata

a doppia parete omologata in caso di installazione all'interno di

una parete imperniata.

9

PARTS IDENTIFIER/ IDENTIFICATION DES PIECES/

NUMERO IDENTIFICATIVO DELLE PARTI

1. Inner Flue Collar

2. Top Flue Collar

3. Brick Liners and Baffle Set

4. Base Bricks

5. Dataplate

6. Log Guard

1

2

3

5

6

4

1. Buse de raccordement du conduit

2. Buse d’étanchéité

3. Briques intérieurs et déflecteurs

4. Briques de sole foyère en fonte

5. Plaque signalétique

6. Garde-bûches

1. Flangia di scarico interna

2. Flangia di scarico superiore

3. Mattoni per pareti interne e set di

lamiere

4. Mattoni per la base

5. Targhetta identificativa

6. Protezione per ceppi

GB FR

IT

10

PRE-INSTALLATION/

INSTRUCTIONS AVANT L'INSTALLATION/

PRE-INSTALLAZIONE

GB: To make the installation of the appliance easier it is best to

remove the internal components before fitting into the builders

opening/studwork.

FR: Pour faciliter l’installation de l’appareil, il est préférable

d’enlever les composants internes avant de l’installer dans

l’ouverture/ossature.

IT: Per semplificare l'installazione della stufa, rimuovere i

componenti interni prima di integrarli nella bocca del camino/

nell'intelaiatura di sostegno.

DOOR/ PORTE/ SPORTELLO

1

2

LOG GUARDS/ GARDE-BÛCHES/

PROTEZIONE PER CEPPI

GB: Do not use appliance without the log guards in position.

FR: Ne pas utiliser l’appareil sans garde-bûches.

IT: Non utilizzare l'apparecchio senza le protezioni per ceppi.

1

2

3

GB: The left and right log guards are handed. The cutouts

must be positioned to the side of the firebox facing

forward.

FR: Les garde-bûches gauche et droit ne sont pas

interchangeables. Les découpes doivent être placées

sur le côté extérieur du corps de chauffe face vers

l'avant.

IT: Sono in dotazione le protezioni per ceppi sinistra e

destra. Le fessure devono essere posizionate sul lato

della scatola di combustione rivolte in avanti.

11

FIREBRICKS & BAFFLE/

BRIQUES RÉFRACTAIRES ET

DÉFLECTEUR/

MATTONI REFRATTARI E DEFLETTORE

1

2

1

GB: Support Baffle Bar

FR: Support de la barre du déflecteur

IT: Barra della lamiera di supporto

2

Baffle Bar

Barre du déflecteur

Barra della lamiera

1

2

3

1

2

3

4

5

1

2

6

1

2

7

8

1

2

3

12

INNER COLLAR/ BUSE D'ETANCHÉITÉ/

ANELLO INTERNO

1

2

3

REMOVAL OF OUTER COLLAR/

RETRAIT DE LA BUSE DE

RACCORDEMENT/

RIMOZIONE DEL COLLARE ESTERNO

Outer Collar

Buse de raccordement

Collare Esterno

1

2

GB: The bolts locate in a bracket in top of the outer box.

This remains in place when installing the flue system.

FR: Les boulons sont situés dans les 4 cavités sur la buse de

raccordement.

La buse de raccordement reste en place pour l’installation du

conduit.

IT: I bulloni vanno inseriti in una staffa sulla sommità della scatola

esterna.

Tutto ciò resta montato quando si installa il sistema del canale

da fumo.

13

GENERAL INFORMATION

Installing the Appliance

Each installation is unique to the property so it is not possible to give

details to suit every setting.

The installation must comply with Building Regulations and be made

using "best practice" construction methods.

Take care when installing the appliance. Careless handling and

use of tools can damage the finish and/or area.

There are 2 types of installation for this appliance:

1. Studwork Installation

2. Fitting to a Masonry Chimney

Appliance Location

This appliance sits in a recess, all nearby walls that are not classed as

re walls or are considered unsuitable for exposure to heat must be

protected by non-combustible building material in accordance with the

specications below.

Seal all joins in the non-combustible material using the method

recommended by the manufacturer.

Ventilate the space between the insert and the recess as specied in

these instructions.

Refer to the manufacturer’s installation instructions when connecting

the chimney system ensuring that the distance to combustible

materials are maintained.

Ensure all combustible materials are not placed closer than 1m from

the front of this appliance.

The appliance must be installed with clearance to the building material,

not in direct contact with it, to allow for thermal expansion of the insert.

Ventilation

Do not pack the void around or above the appliance with insulation

materials such as mineral wool or vermiculite.

The void built for the cassette must be ventilated to prevent a build up

of heat. If the void is sealed then you must fit vents at both low and

high levels of approximately 20cm

2

each. These vents must take cold

air from the room and return warm air back into the room.

An access hatch must be left in the side of the chimney breast for

future servicing and inspection of the flue and appliance.

Building Materials

Stovax recommend building the enclosure from the following materials:

Metal Studwork

Non-combustible board: Calcium Silicate Board - NOT PINK BOARD

Heat Resistant Plaster: Purimacho (any spider cracks that develop

after installation will need to be rubbed down and relled with

Purimacho heat resistant ller to stablise).

Ensure all distances to combustible materials are maintained.

Registered Professional:

Before installation and/or use of this appliance please read these

instructions fully and carefully to ensure that you have fully understood

their requirements.

The appliance must be fitted by a registered installer, or approved by

your local building control officer.

Structural Support:

If installing on a wooden floor check that the floor joists are strong

enough to bear the weight of the insert, chimney and construction

parts.

Hearth:

A Constructional Hearth with a depth of 125mm and a 12mm.

Decorative Hearth Plate must be installed to protect a combustible floor

from the risk of falling embers if mounted directly on the floor.

The Decorative Hearth must extend 300mm in front of the hearth and

can be made of natural stone, concrete, metal or glass.

Final inspection of the installation:

When it has been installed, the appliance must be commissioned in

accordance with standards and practices to ensure full working order

and a correct handover given to the customer.

Flue and Chimney

The flue or chimney system must be able to withstanding flue

temperatures of up to 4000C.

The external diameter of the connection sleeve is 155mm.

In normal operating mode, draft in the chimney should be 20-25 Pa

close to the connection sleeve. The draft is affected primarily by the

length and area of the chimney and also by how well sealed it is.

The minimum recommended chimney length is 3.5m and a suitable

cross-section area is 150-200cm² (140-160 mm in diameter).

Sharp bends and horizontal lengths in a flue pipe reduce the draft in the

chimney.

It must be possible to sweep the full length of the flue, and the soot

doors must be easily accessible.

Carefully check that the chimney is sealed and that there is no leakage

of smoke from the connections.

Combustion Air Supply

When the appliance is installed, it is essential to ensure adequate air

is supplied to the room. Air can be provided indirectly via a vent in the

outer wall or via a duct from the outside that connects to the sleeve on

the underside of the insert. The required volume of combustion air is

about 20 m3/hour.

The outer diameter of the combustion air connection sleeve is 80mm.

If a pipe is longer than 1 m, its diameter must be increased to 100mm

and a larger wall vent will be required.

In heated spaces, the flue must be insulated to prevent condensation

using 30mm mineral wool covered with a vapour barrier. The hole in the

wall (or floor) at the exit point must be properly sealed with flue jointing

compound.

A flexible pipe to provide external directly into the appliance is available

and must be fitted at the time of installation.

CO Alarms

Building regulations require that whenever a new or replacement fixed

solid fuel or wood/biomass appliance is installed in a dwelling a carbon

monoxide alarm, complying with BS EN50291, must be fitted in the

same room as the appliance.

HETAS recommend the unit is permanently fixed in accordance with the

manufacturer's installation instructions or with the guidance contained in

Approved Document J where no other information is available.

Provision of an alarm must not be considered a substitute for either

installing the appliance correctly or ensuring regular servicing and

maintenance of the appliance and chimney system.

GB

14

GENERAL

Model:

Studio Air 1

Studio Air 2

Nominal Heat Output Wood kW 5.0 8.2

Efficiency Wood % 79.6 78.5

CO @ 13% O

2

Wood % 0.12 0.08

Weight Kg 109 149

Recommended Fuels

Wood

Seasoned Wood

(less than 20% moisture content)

As tested to the requirements of EN 13229 for intermittent operation

FLUES

Flue/Chimney Size

With Liner of Factory made system

(diameter)

installed in accordance with manufacturers

instructions

mm

153 153

inch

6 6

Flue/Chimney

minimum height

All products

m

4.5 4.5

feet

15 15

Flue Draught

Min

Pa

10 10

Nominal

12 12

Max

20 20

Flue Gas Mass Flow Wood g/s 4.7 6.5

Average Flue Gas

Temperature

Wood

o

C 261 304

Flue Outlet Size

(Top Option)

mm 153 153

inch 6 6

European Min Spec for Solid Fuel Chimney Flue - T400 N2 D 3 G50

VENTILATION

A) Traditionally Built Homes

• Where leakage is greater than 5m

3

/hour/m

2

.

• Ventilation normally required = 550mm

2

per kW output over 5kW

B) Modern Construction Homes

• Where leakage is less than 5m

3

/hour/m

2

.

• Ventilation normally required = 550mm

2

per kW

A

Additional Ventilation

mm2 None 1760

cm2 None 17.6

in2 None 2.84

B

Additional Ventilation

mm2 2750 4510

cm2 27.5 45.10

in2 4.44 7.28

ESSENTIAL INFORMATION

GB

15

Mandatory for smoke control areas

This appliance is supplied with a pre-tted smoke

control setting and has been independently tested

to PD6434 making it exempt from the controls that

generally apply in Smoke Control Areas.

THE SMOKE CONTROL FACILITY IS SUPPLIED

DISABLED AND MUST THEREFORE BE MODIFIED

IN ORDER FOR THE APPLIANCE TO MEET THE

REQUIREMENTS OF A SMOKE CONTROL AREA

AND MUST BE OPERATED CORRECTLY TO

MINIMISE THE AMOUNT OF SMOKE PRODUCED.

Any modifications to the setting should only be

done by a suitably qualified installer and must be

done at the time of installation.

Studio Air 2 shown

1

All Models

Undo the screw and remove the 2x nuts.

Keep the nuts in a safe place for future use.

Studio Air 2 shown

2

SMOKE CONTROL AREA SETTINGS

Studio Air 2 shown

3

To meet the requirements of a Smoke Control Area the appliance

MUST be operated correctly in order to minimise the amount of

smoke produced.

If this appliance is installed outside of a Smoke

Control Area then the Smoke Control facility can be

disabled to give more control over the lower burn

rates.

These instructions must be left with the User.

GB

16

Make provision during installation for the connection of the

following:

- Decorative Frame (if required)

- Electrical services (for fan installation) using the opening

in the side of the chimney breast for access.

- The Outside Air Kit (optional)

- Convection Ducting Kit (optional)

- The flue system (see Installation. Flue Assembly)

Important Note: If you plan to install an optional fan kit,

outdoor air kit or ducting kit preparation must be made for

the installation of wiring, sockets and exit/inlet holes before

installation.

The appliance is supplied with a frameless Edge finish as part of

the outer box and does not require any additional modifications for

this method of installation.

Build the chimney breast to support the cassette.

Ensure all clearances to combustible material are maintained, see

Clearance Section.

To prevent cracking ensure no joints above the appliance.

A

B

C

250mm minimum

if fan kit fitted

Ensure provision for a vent

of at least 200 cm

2

is made

if fan kit fitted

STUDWORK

DIMENSION (MM) A B C

Studio Air 1 460 800 350

Studio Air 2 485 1000 350

MASONRY

DIMENSION (MM) A B C

Studio Air 1 470 800 350

Studio Air 2 495 1000 350

STUDWORK INSTALLATION

In a studwork installation it is recommended that this

appliance is used in conjunction with a twin wall flue system

that is used the entire length of the flue down to the appliance.

Stovax have designed their own Professional XQ range and

details of this product are available from your Stovax retailer.

There are 2 methods of installation:

Frameless Edge Installation

Fitting with a Decorative Frame

Carefully read the relevant section for the installation method

required.

Do not pack the void around or above the appliance with

insulation materials such as mineral wool or vermiculite.

The void built for the cassette must be ventilated to prevent a

build up of heat. If the void is sealed then you must fit vents at

both low and high levels of approximately 50cm

2

each. These

vents must take cold air from the room and return warm air

back into the room.

An access hatch must be left in the side of the chimney breast

for future servicing and inspection of the flue and appliance.

FITTING TO A MASONRY CHIMNEY

In a masonry installation it is recommended the appliance is

used in conjunction with a flue liner.

There are 2 methods of installation:

Frameless Edge Installation

Fitting with a Decorative Frame

Carefully read the relevant section for the installation method

required.

Many fireplace openings have a supporting lintel. Do not remove

without supporting the remaining structure of the building. Do not

support the structure with the appliance or the flue system.

Stovax recommend the use of a flue liner when installing into

a masonry chimney. Alternative methods can be used if the

chimney is sound and correctly sized, however access may be

required to make an effective seal - ie Using a sump adapter.

INSTALLATION

GB

17

FRAMELESS EDGE INSTALLATION

The Edge Frame consists of 3 adjustable sections to ensure a

flush finish with the non combustible board and final plaster skim.

To adjust the Edge Frame loosen the screws on the outside of the

outer box flanges.

Remove to adjust

Remove

to adjust

Remove

to adjust

Slide flanges to adjust to desired depth.

Tighten screws.

Insert the appliance into the aperture and secure through the fixing

holes.

Fixing

Holes

The position of the box can now be improved within the builder's

opening by adjusting the four levelling feet to ensure it sits firm and

level at all four corners.

Adjust each

corner using

leveling feet

Wind the set screws down to the desired position in each corner.

Use M6 or M8 bolts to secure the outer case to the masonry

of the fireplace. There must be at least two bolts in the rear

and one in either side. Check the security of these fasteners

before proceeding to fit the inner box.

Fixings must be positioned within the shaded area shown to

avoid interfering with fan or Outdoor Air kit installations.

Do not over tighten and deform the firebox.

This appliance MUST be securely fixed in position to support the

door when opened.

Shaded area for fixing bolts

Right Hand Side of Outer BoxLeft Hand Side of Outer Box

Shaded area for fixing bolts

Fit non combustible board to studwork around the outer box up to

the adjustible edge frame and leave enough room for the final skim

of heat resistant plaster.

GB

18

Standard plasterboard is not suitable.

This should extend a minimum of 600mm to the sides and above

the appliance.

Non combustible zone

Plaster board

Apply a heat resistant lime plaster finish to at least 900mm above

and 400mm to the sides of the chimney breast, making sure it is

not too thin or it will crack.

Heat resistant plaster

Non combustible plasterboard

Adjustable

edge frame

Flue clamp plate

Connect the flue system, see Flue Section.

To finish this installation re-install the inner box.

After commissioning, finish the sides of the chimney breast.

50cm

2

vents

Inspection

Hatch

300mm x

300mm

FITTING WITH A DECORATIVE FRAME

The appliance can be fitted with a decorative frame after

installation. Install in conjunction with the Frame instructions

supplied.

Fit non combustible board to studwork around the aperture.

Standard plasterboard is not suitable.

This should extend a minimum of 600mm to the sides and above

the appliance.

Apply a heat resistant plaster finish to at least 900mm above and

400mm to the sides of the chimney breast, making sure it is not

too thin or it will crack.

Insert the outer box into the aperture.

The position of the box can now be improved within the builder's

opening by adjusting the four levelling feet to ensure it sits firm and

level at all four corners.

Adjust each

corner using

leveling feet

GB

19

Wind the set screws down to the desired position in each corner.

Use M6 or M8 bolts to secure the outer case to the masonry

of the fireplace. There must be at least two bolts in the rear

and one in either side. Check the security of these fasteners

before proceeding to fit the inner box.

Fixings must be positioned within the shaded area shown to

avoid interfering with fan or Outdoor Air kit installations.

Do not over tighten and deform the firebox.

This appliance MUST be securely fixed in position to support the

door when opened.

Shaded area for fixing bolts

Right Hand Side of Outer BoxLeft Hand Side of Outer Box

Shaded area for fixing bolts

Secure through the fixing holes.

Fixing

Holes

Connect the flue system, see Flue Section.

To finish this installation re-install the inner box.

After commissioning, finish the sides of the chimney breast.

Studwork Installation

50cm

2

vents

Inspection

Hatch

300mm x

300mm

GB

20

MASONRY INSTALLATION

In a masonry installation it is recommended the

appliance is used in conjunction with an insulated

flue liner

Existing chimneys must be pre swept and lined before use.

Flue liner

Fill

250mm

(minimum)

if fan is fitted

Studio Air

Outer Box

Mid

Lintel

Supporting

lintel

Ensure flue is

clear of masonry

Outer Flue Collar

Flue Liner

Adaptor

FLUE ASSEMBLY

STUDWORK INSTALLATION

In a studwork installation it is recommended that

this appliance is used in conjunction with a twin

wall flue system that is used the entire length

of the flue down to the appliance. Stovax have

designed their own Professional XQ range and

details of this product are available from your

Stovax retailer.

Twin Wall

System

Studio Air

Outer Box

Decorative

starter piece

Outer Flue Collar

Stovax Starter

Piece

250mm

(minimum)

if fan is fitted

GB

La page charge ...

Stovax Studio Air Icon XS Guide d'installation

Ce manuel convient également à

Stovax Studio Air Icon XS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents