Sauder 409048 Mode d'emploi

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

English pg 1-26

Français pg 27-29

Español pg 30-32

Lot # 374894 06/23/15

Purchased: __________________

Be sure to give us a ring before

making any returns. 1-800-523-3987

Entertainment Credenza

Edge Water Collection | 409048

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.

Prefer the phone? Call 1-800-523-3987.

Share your journey!

sauder.com

Entertaining what

entertains you.

Table of Contents Assembly Tools Required

3

4-5

6-26

27-29

30-32

33-34

35

Part Identiﬁ cation

Hardware Identiﬁ cation

Assembly Steps

Français

Español

Safety

Warranty

Hammer

Not actual size

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or

death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.

• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!

• This Sauder unit is designed for use with televisions weighing less than 95 pounds. Never use with a TV that weighs more.

• The size of the television, front-to-back and side-to-side, must ﬁ t within the space deﬁ ned in the diagram.

• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)

• Never allow the sides of the TV to extend past the side edges of the TV support surface.

• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.

• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.

WARNING

!

95 lbs.

15 1/2"

58-3/4"

Skip the power trip.

This time.

409048 www.sauder.com/servicesPage 2

Part Identiﬁ cation

å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge

to help distinguish similar parts from each other. Use this part identiﬁ cation to help identify similar parts.

A RIGHT END (1)

B LEFT END (1)

C RIGHT UPRIGHT (1)

D LEFT UPRIGHT (1)

E2 TOP (1)

F BOTTOM (1)

G SHELF (1)

H BACK (1)

I DOOR (2)

J ADJUSTABLE SHELF (5)

K2 LEG (2)

L VALANCE (1)

M DRAWER FRONT (1)

D62 DRAWER BACK (1)

D12 RIGHT DRAWER SIDE (1)

D13 LEFT DRAWER SIDE (1)

D701 DRAWER BOTTOM (1)

R SPACER (2)

S BOTTOM MOLDING (1)

Y FOOT (2)

XX STOP MOLDING (1)

Now you know

our ABCs.

409048www.sauder.com/services

Page 3

A

B

C

D

E2

F

G

H

I

J

K2

L

R

S

K2

I

R

Y

J

M

D62 D12

D13

D701

XX

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

35DA

CABINET RIGHT -1

35DD

DRAWER LEFT - 1

35DC

DRAWER RIGHT - 1

35DB

CABINET LEFT - 1

PLASTIC FOOT - 2

X

Z

TWIST-LOCK

®

FASTENER - 16

HIDDEN CAM - 8

1F

CAM SCREW - 8

8F

GROMMET - 1

DD

GROMMET CAP - 1

EE

ANGLE BRACKET - 6

FF

KNOB - 4

GG

BACKPLATE - 2

HH

II

SLIDE CAM - 2

FELT DISC CARD - 1

JJ

METAL PIN - 20

LL

RUBBER SLEEVE - 20

MM

(Refer to Step 20 for proper

location and application)

WARNING LABEL - 1

NN

WARNING

Never use this furniture with a TV that is too

large or too heavy. Severe injury or death

can occur. The TV and furniture will be

unstable and may tip.

-The TV must less than 95 lbs.

-The base of the TV must be able to sit

completely on this shelf.

-Refer to instruction book for complete

safety information.

Note: This is a permanent label. Do not try

to remove. Surface will be damaged.

02/ 02 269227

409048 www.sauder.com/servicesPage 4

WOOD DOWEL - 5

15F

GLUE - 1

54M

CC

HINGE - 4

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

BLACK 1-7/8" FLAT HEAD SCREW - 4

OO

BLACK 1-1/8" MACHINE SCREW - 2

QQ

RR

BROWN 1" FLAT HEAD SCREW - 4

BLACK 7/8" MACHINE SCREW - 2

SS

BLACK 9/16" LARGE HEAD SCREW - 12

TT

BLACK 1/2" FLAT HEAD SCREW - 8

UU

VV

GOLD 5/16" FLAT HEAD SCREW - 8

NAIL - 42

WW

409048www.sauder.com/services

Page 5

30S

BLACK 1-9/16" FLAT HEAD SCREW - 6

Step 1

Look for this icon. It means a

video assembly tip is available at

www.sauder.com/services/tips

å

Assemble your unit on a carpeted ﬂ oor or on the empty

carton to avoid scratching your unit or the ﬂ oor.

å

To begin assembly, push a SAUDER TWIST-LOCK®

FASTENER (Z) into the large holes in the RIGHT END (A)

and LEFT END (B).

å

Repeat this step for the UPRIGHTS (C and D), BOTTOM (F),

and SHELF (G).

409048 www.sauder.com/servicesPage 6

B

A

(16 used)

Z

Do not tighten the TWIST-LOCK® FASTENERS in this step.

STOP

If you purchased

the 409049 TV

Wall with Bracket,

assemble that

unit ﬁ rst.

Scan this QR code or go to this address:

http://qr.sauder.com/?ID=1188

to watch a video on how to assemble your unit.

å

Push eight HIDDEN CAMS (1F) into the ENDS (A and B)

and TOP (E2).

Step 2

409048www.sauder.com/services

Page 7

Arrow

The arrow in the HIDDEN

CAM must point toward the

hole in the edge of the board.

Hole

Do not tighten the HIDDEN CAMS in this step.

B

A

Surface with

TWIST-LOCK®

FASTENERS

Surface with

TWIST-LOCK®

FASTENERS

1F

Arrow

1F

E2

Arrow

1F

Step 3

å

Turn eight CAM SCREWS (8F) into the LEGS (K2) and

STOP MOLDING (XX).

Remember:

Righty tighty.

Lefty loosey.

8F

K2

XX

409048 www.sauder.com/servicesPage 8

å

First, ﬁ ll the holes in the STOP MOLDING (XX) 1/4 to 1/2 full

with GLUE (54M). Then, insert ﬁ ve WOOD DOWELS (15F)

into the holes. Wipe away the excess GLUE.

å

Now, ﬁ ll the holes in the edge of the TOP (E2) 1/4 to 1/2 full

with GLUE.

å

Fasten the TOP (E2) to the STOP MOLDING (XX). Tighten

four HIDDEN CAMS.

å

NOTE: Be sure the WOOD DOWELS in the STOP MOLDING

insert into the holes in the edge of the TOP. Wipe away the

excess GLUE.

Step 4

12

409048www.sauder.com/services

Page 9

Fill the holes 1/4 to 1/2 full with GLUE.

Inspect the parts thoroughly before

assembling. Disassembly of glued

parts is extremely di cult.

Caution

!

54M

15F

(5 used)

E2

Surface with HIDDEN CAMS

XX

Seam

Step

å

Fasten the LEGS (K2) to the ENDS (A and B). Tighten four

HIDDEN CAMS.

å

Fasten the FEET (Y) to the LEGS (K2). Use two BLACK

1-9/16" FLAT HEAD SCREWS (30S).

Step 5

409048 www.sauder.com/servicesPage 10

K2

B

A

Surface with

TWIST-LOCK®

FASTENERS

Surface with

TWIST-LOCK®

FASTENERS

Y

These surfaces should be even.

BLACK 1-9/16" FLAT HEAD SCREW

(2 used in this step)

30S

Step

409048www.sauder.com/services

Page 11

Step 6

å

Fasten the CABINET RIGHT (35DA) and CABINET

LEFT (35DB) to the UPRIGHTS (C and D). Use four

GOLD 5/16" FLAT HEAD SCREWS (VV).

GOLD 5/16" FLAT HEAD SCREW

(4 used in this step)

VV

D

C

35DA

35DB

Roller end

1

3

2

1

3

2

Surface without

TWIST-LOCK®

FASTENERS

Surface without

TWIST-LOCK®

FASTENERS

Roller end

Finished edge

Step

å

Fasten the SHELF (G) to the UPRIGHTS (C and D).

Tighten four TWIST-LOCK® FASTENERS.

Step 7

409048 www.sauder.com/servicesPage 12

Finished edge

How to use the SAUDER TWIST-LOCK

®

FASTENER

1. Insert the dowel end of the FASTENER into the hole of the

adjoining part.

NOTE: The dowel end of the FASTENER must remain fully

inserted in the hole of the adjoining part while locking

the FASTENER.

2. Tighten the FASTENER with a Phillips screwdriver as tight

as possible.

Surface with

TWIST-LOCK®

FASTENERS

Surface with

TWIST-LOCK®

FASTENERS

Surface without

TWIST-LOCK®

FASTENERS

D

C

G

Dowel end

Do not stand the unit upright without the

BACK fastened. The unit may collapse.

Caution

Step

409048www.sauder.com/services

Page 13

Step 8

å

Fasten the LEFT END (B) to the TOP (E2). Tighten two

TWIST-LOCK® FASTENERS.

å

Fasten the UPRIGHTS (C and D) to the TOP (E2). Tighten

four TWIST-LOCK® FASTENERS.

K2

B

D

C

Surface with

TWIST-LOCK®

FASTENERS

E2

Finished edge

Surface with

HIDDEN CAMS

XX

Step

å

Fasten the BOTTOM (F) to the LEFT END (B). Tighten two

TWIST-LOCK® FASTENERS.

å

Fasten the BOTTOM (F) to the UPRIGHTS (C and D). Use

four BLACK 1-7/8" FLAT HEAD SCREWS (OO).

Step 9

409048 www.sauder.com/servicesPage 14

Surface with

TWIST-LOCK®

FASTENERS

B

D

C

F

These holes must be here.

BLACK 1-7/8" FLAT HEAD SCREW

(4 used in this step)

OO

Step

409048www.sauder.com/services

Page 15

Step 10

å

Fasten the RIGHT END (A) to the TOP (E2) and

BOTTOM (F). Tighten four TWIST-LOCK® FASTENERS.

A

Surface without

TWIST-LOCK®

FASTENERS

E2

F

K2

Step 11

å

Fasten two ANGLE BRACKETS (FF) to the VALANCE (L).

Use two BLACK 9/16" LARGE HEAD SCREWS (TT).

å

NOTE: Be sure the edges of the ANGLE BRACKETS are

even with the edge of the VALANCE.

å

Fasten four ANGLE BRACKETS (FF) to the BOTTOM (F).

Use four BLACK 9/16" LARGE HEAD SCREWS (TT).

å

NOTE: Be sure the edges of the ANGLE BRACKETS are

even with the edge of the BOTTOM.

å

Fasten the BOTTOM MOLDING (S) to the BOTTOM (F).

Use four BLACK 9/16" LARGE HEAD SCREWS (TT).

å

Fasten the VALANCE (L) to the TOP (E2). Use two BLACK

9/16" LARGE HEAD SCREWS (TT).

409048 www.sauder.com/servicesPage 16

BLACK 9/16" LARGE HEAD SCREW

(12 used in this step)

TT

F

L

FF

S

E2

Curved edge

Finished surface

Curved edge

L

FF

Unﬁ nished surface

å

Carefully turn your unit over onto its front edges. Unfold the

BACK (H) and lay it over your unit.

å

Make equal margins along all four edges of the BACK (H). Push

on opposite corners of your unit if needed to make it "square".

å

Fasten the BACK (H) to your unit using the NAILS (WW).

å

NOTE: Be sure to tap NAILS into the holes that line up over

the UPRIGHTS (C and D).

å

NOTE: Perforations have been provided for access through the

BACK. Carefully cut out the holes needed.

Step 12

409048www.sauder.com/services

Page 17

Unﬁ nished surface

These holes must line up over

the UPRIGHTS (C and D).

NAIL

(42 used in this step)

WW

H

Do not stand the unit upright without the

BACK fastened. The unit may collapse.

Caution

Step 13

å

Fasten the SPACERS (R) to the BOTTOM (F). Use four

BROWN 1" FLAT HEAD SCREWS (RR).

å

Push the PLASTIC FEET (X) into the holes in the SPACERS (R).

409048 www.sauder.com/servicesPage 18

F

X

R

X

BROWN 1" FLAT HEAD SCREW

(4 used in this step)

RR

å

Fasten two HINGES (CC) to each DOOR (I). Use eight

BLACK 1/2" FLAT HEAD SCREWS (UU).

Step 14

409048www.sauder.com/services

Page 19

I

BLACK 1/2" FLAT HEAD SCREW

(8 used in this step)

UU

CC

Step 15

å

Carefully stand your unit upright.

å

Before fastening the DOOR to your unit, be sure the

mounting screw is against the stops as shown in the right

diagram. If it isn't, loosen the mounting screw to slide it

against the stops. Then tighten the mounting screw.

å

Fasten a DOOR (I) to the RIGHT END (A). Use the screws

provided in the HINGES. See the next step for adjustments.

å

Fasten a KNOB (GG) and BACKPLATE (HH) to the DOOR (I).

Use a BLACK 1-1/8" MACHINE SCREW (QQ).

å

Peel the FELT DISC from the FELT DISC CARD (JJ). Stick a

FELT DISC on the DOOR where it comes in contact with the

RIGHT UPRIGHT (C).

å

Repeat this step for the other DOOR (I).

409048 www.sauder.com/servicesPage 20

BLACK 1-1/8" MACHINE SCREW

(2 used in this step)

QQ

HH

GG

Pro Tip: Lift with your

legs. And, you know,

your arms.

JJ

C

A

I

Mounting

screw

Stop

Hinge

La page charge ...

Sauder 409048 Mode d'emploi

Ce manuel convient également à

Sauder 409048 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents